Scribd
Upload
57 views1 page

(Preview) Paradox Security Systems - Spectra 1728 & 1728EX Programming Guide

This document provides programming instructions for security system models 1728, 1728EX, 1738, and 1738EX. It outlines how to enter programming mode by entering the installer code and section number. A decimal and hexadecimal programming table shows what numbers and letters to press to enter values. The guide also describes how to view trouble conditions by pressing the TBL or TRBL key and lists different types of troubles that can occur, identified by numbers on the keypad.

Uploaded by

iulian.avram
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
57 views1 page

(Preview) Paradox Security Systems - Spectra 1728 & 1728EX Programming Guide

This document provides programming instructions for security system models 1728, 1728EX, 1738, and 1738EX. It outlines how to enter programming mode by entering the installer code and section number. A decimal and hexadecimal programming table shows what numbers and letters to press to enter values. The guide also describes how to view trouble conditions by pressing the TBL or TRBL key and lists different types of troubles that can occur, identified by numbers on the keypad.

Uploaded by

iulian.avram
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

1728, 1728EX, 1738 AND 1738EX

SYSTEM PROGRAMMING GUIDE


Software Version 2.0

DEFAULT INSTALLER CODE


000000 (see section [281] on page 15)
DEFAULT SYSTEM MASTER CODE
123456 (see section [301] on page 15)
HOW DO I ENTER PROGRAMMING MODE?
STEP 1: Press [ENTER ]
STEP 2: Enter your [INSTALLER CODE]
STEP 3: Enter 3-digit [SECTION] you wish to program
STEP 4: Enter required [DATA]

DECIMAL AND HEXADECIMAL PROGRAMMING TABLE

What Do I What Do I See?


Value or Action
Press? 10-Zone LED 16-Zone LED LCD
Values 1 to 9 [1] to [9] [1] to [9] [1] to [9] [1] to [9]
A (hexa only) [0] [0 (10)] [10] 0
B (hexa only) [STAY ] [STAY ] [11] B
C (hexa only) [BYP ] [BYP ] [12] C
D (hexa only) [MEM ] [MEM ] [13] D
E (hexa only) [TBL] / [TRBL] [TBL] [14] E
F (hexa only) [PG ] / [FNC 1] [PG ] [15] F
Exit Without Saving [CLEAR] [ENTER ] flashes [ARM1] & [STAY1] flash “SECTION [ ]”
Erase Current Digit [FORCE ] Displays next digit or next section
Save Data (hexa only) [ENTER ] Advances to the next section

TROUBLE DISPLAY
Press the [TBL ] or [TRBL] key to view the Trouble Display. Please note that the keypad can be programmed to emit a BEEP
every 5 seconds whenever a new trouble condition has occurred. Press the [TBL ] or [TRBL ] key to stop the beeping.

[1] - No Battery or Low Battery [8] - Timer Loss***


[2] - Wireless Transmitter Low Battery** [9] - Tamper or Zone Wiring Failure*
[3] - Power Failure [10] - Telephone Line Monitoring Failure
[4] - Bell Output Disconnected [11]/[STAY] - Fire Loop Trouble*
[5] - Maximum Bell Current [12]/[BYP ] - Module Loss
[6] - Maximum Auxiliary Current [13]/[MEM] - Wireless Transmitter Supervision Loss*
[7] - Communicator Report Failure [16]/[FORCE ] and [TBL ]/[TRBL ] flashes - Keypad Fault

* press the illuminated key ([9], [STAY ] or [M EM ]) to view which zones are causing the trouble. Enter the Installer Code to clear
Tamper troubles.
** press [2] to view which zones are causing the trouble (on SPC-319 versions higher than 1.0).
*** press [8] to re-program the time.
Spectra 1728/EX & 1738/EX -1- Programming Guide
www.PDF-Zoo.com

You might also like