USER MANUAL

Information in this manual is subject to change without notice and does not represent a commitment on
the part of Applied Acoustics Systems DVM Inc. The software described in this manual is furnished under a
license agreement. The software may be used only in accordance of the terms of this license agreement. It is
against the law to copy this software on any medium except as specifically allowed in the license agreement.
No part of this manual may be copied, photocopied, reproduced, translated, distributed or converted to any
electronic or machine-readable form in whole or in part without prior written approval of Applied Acoustics
Systems DVM Inc.
Copyright c 2019 Applied Acoustics Systems DVM Inc. All rights reserved. Printed in Canada.
Program Copyright c 2004-2019 Applied Acoustics Systems, Inc. All right reserved.
Ultra Analog VA is a Trademark of Applied Acoustics Systems DVM Inc. Windows and Windows Vista
are registered trademarks of Microsoft Corporation in the United States and other countries. Mac OS and
Audio Units are registered trademarks of Apple Corporation. VST Instruments and ASIO are trademarks
of Steinberg Soft Und Hardware GmbH. AAX is a registered trademarks of Avid Technology Inc. All
other product and company names are either trademarks or registered trademarks of their respective owner.
Unauthorized copying, renting or lending of the software is strictly prohibited.
Visit Applied Acoustics Systems DVM Inc. at www.applied-acoustics.com
Contents

1 Introduction 6
1.1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Installation and Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.3 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3.1 Using Ultra Analog Session in Standalone Mode . . . . . . . . . . . . . . 8
1.3.2 Exploring the Factory Sounds . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3.3 Using Ultra Analog Session as a Plug-in . . . . . . . . . . . . . . . . . . . 9
1.4 Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.5 About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 Architecture of the Ultra Analog Session 10

3 Bank and Program Management 11

3.1 Banks and Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 Saving Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.3 The Bank Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.4 Using MIDI Bank and Program Changes . . . . . . . . . . . . . . . . . . . . . . . 13
3.5 Backups of Banks and Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.6 Exchanging Banks and Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.7 Restoring the Factory Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4 Parameters 15
4.1 General Functioning of the Interface . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1.1 Knobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1.2 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1.3 Drop-down Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1.4 Modulation Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.1.5 Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.2 The Mode Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.3 Unison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.4 The Arpeggiator Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4 CONTENTS

4.5 The Oscillator Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.6 The Filter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.7 The Amp Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.8 The Effect Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.8.1 Chorus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.8.2 Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.8.3 Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.8.4 Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.8.5 Flanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.8.6 Phaser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.8.7 Reverb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.9 Pitch Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.10 Modulation Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.11 Ribbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5 Utility Section 32
5.1 The MIDI LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.2 Polyphony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.3 Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.4 History and Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.5 Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.6 Level Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.7 The About Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

6 Audio and MIDI Settings 35

6.1 Audio Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.1.1 Selecting an Audio Device . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.1.2 Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.2 MIDI Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.2.1 Selecting a MIDI Device . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.2.2 Creating MIDI Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.2.3 Creating a default MIDI Map . . . . . . . . . . . . . . . . . . . . . . . . 36
6.2.4 MIDI Program Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CONTENTS 5

6.2.5 MIDI Bank Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

6.2.6 Pitch bend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
6.2.7 Modulation wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

7 Using Ultra Analog Session as a Plug-In 38

7.1 Audio and MIDI Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.2 Automation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.3 Multiple Instances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.4 Saving Projects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.5 Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

8 License Agreement 39
6 Introduction

1 Introduction

Ultra Analog Session is a virtual analog synthesizer. This special edition is based on modules from
the well-known AAS Ultra Analog-VA synthesizer. With this instrument, we have not attempted
to emulate a specific vintage analog synthesizer but rather to combine into a modern instrument,
different features of legendary synthesizers. The design of this instrument allows one to get a wide
range of tone from vintage analog to that of modern virtual analog synthesizers. Key controls and
effects have been included resulting in a simple yet creative and versatile instrument.
Ultra Analog Session generates sound by simulating the different components of the synthe-
sizer through physical modeling. This technology uses the laws of physics to reproduce how an
object or system produces sound. In the case of Ultra Analog Session, mathematical equations
describing how analog circuits function are solved in real-time. Ultra Analog Session uses no
sampling nor wavetable, it just calculates the sound as you play in accordance with the controls
it receives. This sound synthesis method ensures unmatched sound quality, realism, warmth and
playing dynamics.
Before discussing the synthesizer in more detail, we would like to take this opportunity to thank
you for choosing an AAS product. We sincerely hope that this product will bring you inspiration,
pleasure and fulfill your creative needs.

1.1 System Requirements

The following minimum computer configuration is necessary to run Ultra Analog VA:

Mac OS

• Mac OS X 10.11 (El Capitan) or later

• Intel Core i5 (circa 2012), Apple M1 processor or later
• 64-bit DAW

Windows

• Windows 10 64-bit or later

• Intel Core i5 (circa 2015) or later
• 64-bit DAW

Keep in mind that the computational power required by Ultra Analog VA depends on the num-
ber of voices of polyphony and the sampling rate used. These computer configurations will enable
you to play the factory sounds with a reasonable number of voices but performances will vary
depending on your specific computer configuration.
1.2 Installation and Authorization 7

1.2 Installation and Authorization

Installation and authorization of Ultra Analog VA is quick and easy. For the installation of our
different products we use so-called custom installers which include both the program itself and
your licence information. Installation and authorization can therefore be carried out automatically
in a single step and from a single file when your computer is online. AAS products use a a copy
protection system based on a a proprietary challenge/response key exchange and therefore their
authorization does not rely on other third party software and/or hardware.
In order to start the installation process, simply double-click on the installer file that you have
downloaded. This will first install the program and then use the licence information included in the
custom installer file to to carry out automatically the challenge/response procedure.
Once the installation is completed, you can check your licence information by starting the
program and clicking on the chevron icon at the top of the interface. This will open a dialog box in
which you should see your serial number and the email address which you used in order to get the
installer file. Note that your serial number is also sent to you by email when your custom installer
is created.
If your computer is offline when running the installer, or if the authorization procedure could
not be completed for another reason, the dialog box will will not show your serial number and
you will be prompted to authorize the program. In that case, click on the Authorize button and
follow the on-screen instructions. Note that it is possible to use the program during 15 days before
completing the authorization process. After that period, the program will not function unless it is
authorized.

1.3 Getting Started

1.3.1 Using Ultra Analog VA in Standalone Mode

Ultra Analog VA comes with a standalone versions allowing you to play it without having to open
your sequencer. This can be convenient to explore Ultra Analog VA and its library, play it live
or do some sound design work. To start Ultra Analog VA in standalone mode, simply follow the
instructions below:

• Windows - Double-click on the Ultra Analog VA icon located on your desktop or select
Ultra Analog VA from the Start > All Programs > menu.

• Mac OS - Double-click on the Ultra Analog VA icon located in the Applications folder.

Before you start exploring the program, take a moment to set up you audio and MIDI configu-
ration as explained below.
8 Introduction

Audio and MIDI Configuration

Audio and MIDI configuration tools are available by clicking on the Audio Setup button located
in the lower left corner of the Ultra Analog VA interface. The Audio Setup dialog first allows you
to select an audio output device from those available on your computer. Multi-channel interfaces
will have their outputs listed as stereo pairs.
On Windows, the audio output list is organized by driver type. The device type is first selected
from the Audio Device Type drop-down list. If you have ASIO drivers available, these should be
selected for optimum performance. The Configure Audio Device button allows you to open the
manufacturer’s setup program for your audio interface when available.
Once the audio input has been selected, you can then select a sampling rate and a buffer size
from those offered by your audio interface.
The list of available MIDI inputs appears at the bottom of the dialog. Click on the checkbox
corresponding to any of the inputs you wish to use.

1.3.2 Exploring the Factory Sounds

Ultra Analog VA comes with a wide range of factory programs right out of the box which amounts
to a huge range of sounds before you have even turned a single knob. As you would expect, the
best way of coming to grips with the possibilities Ultra Analog VA offers is simply to go through
the programs one at a time.
Ultra Analog VA uses the notions of Banks and Programs to organize and classify sounds. A
program or preset is a stored set of parameters corresponding to a given sound. The programs are
grouped and organized in banks.
The name of the currently loaded bank and program are displayed at the top of the interface.
One navigates among the different banks and programs by using the arrows in each of the cor-
responding boxes or by opening the associated drop-down menu by clicking inside these boxes.
Banks and programs are managed using the Bank Manager which is revealed by clicking on the
Manage button appearing above the right-top corner of the Bank box. Playing programs and or-
ganizing them is pretty straightforward, please refer to Chapter 3 for a complete description of the
bank and program management operations.

1.3.3 Using Ultra Analog VA as a Plug-in

Ultra Analog VA integrates seamlessly into the industry’s most popular multi-track recording and
sequencing environments as a virtual instrument plug-in. Ultra Analog VA works as any other
plug-in in these environments so we recommend that you refer to your sequencer documentation
in case you have problems running Ultra Analog VA as a plug-in. Note that in plug-in mode the
audio and MIDI inputs, sampling rate, and buffer size are determined by the host sequencer.
1.4 Getting Help 9

1.4 Getting Help

AAS technical support representatives are on hand from Monday to Friday, 9am to 6pm EST.
Whether you have a question on Ultra Analog VA, or need a hand getting it up and running as a
plug-in in your favorite sequencer, we are here to help. Contact us by phone or email at:

• North America Toll Free: 1-888-441-8277

• Worldwide: 1-514-871-8100

• Email: [email protected]

Our online support pages contain downloads of the most recent product updates, and answers
to frequently asked questions on all AAS products. The support pages are located at:

1.5 About this Manual

Throughout this manual, the following conventions are used:

• Bold characters are used to name modules, commands and menu names.

• Italic characters are used to name controls on the interface.

• Windows and Mac OS keyboard shortcuts are written as Windows shortcut/Mac OS shortcut.
10 Bank and Program Management

2 Architecture of the Ultra Analog Session

Ultra Analog Session is a synthesizer based on the AAS modeling technology. It is a simple
synthesizer yet its clever design results in a surprisingly versatile instrument that is really fun to
play with.
The sound source is a rectangular wave VCO with hard synchronisation possibilities. This
wave generator is also modulated by a triangular waveform LFO allowing for a wind range of
sounds. This source is sent to a resonant low pass filter and an effect processor for further sound
shaping. Ultra Analog Session includes an unison mode and features an arpeggiator for the creation
of rhythmic sequences. The functioning and different parameters of these modules are discussed
in more details in the next section.

Figure 1: Graphical user interface of Ultra Analog Session Synthesizer.

3 Bank and Program Management

Ultra Analog Session comes with several factory presets, called programs, covering a wide range
of sounds. This collection of programs lets you play and familiarize yourself with this synthesizer
without having to tweak a single knob. Soon, however, you will be experimenting and creating
your own sounds and projects that you will need to archive or exchange with other users. In this
section, we review the management of programs.
3.1 Banks and Programs 11

3.1 Banks and Programs

Sounds are stored in banks contaning so-called programs. The name of the currently selected bank
is shown in the Bank drop-down display located at the top of the Ultra Analog Session interface.
The list of available banks is viewed by clicking on the Bank display. A bank can be selected by
navigating in the list of banks using the left and right-pointing arrows in the display or by clicking
on its name when the list of banks is open. Clicking on the bank display brings focus on this section
of the interface, the display is then outlined by an orange line, and one can then navigate through
the list of banks using the up, down, left, or right arrows of the computer keyboard.
The list of programs included in the currently selected bank can be viewed by clicking on the
Program display located below the Bank display. A program is selected by using the left and right-
pointing arrows or by clicking directly on its name. Once a program is selected, the value of the
different parameters of the synthesizer are updated and it can then be played. As for the bank list,
one can navigate through the program list using the computer arrows after clicking on the Program
display.

3.2 Saving Programs

Programs are saved by clicking on the Save button located on the top of the Program display. When
a program has just been loaded, this command is greyed and therefore inactive. It is activated as
soon as a parameter of the interface is modified. Clicking on this command replaces the stored
version of the program with the new one.
The Save As command is activated by clicking on the corresponding button which opens the
Save Program pop-up window. It is then possible to save the program under a new name or its
current one in any of the available program banks. Note that if the original name of the program
is used, a new program with the same name will be created at the end of the program list meaning
that the original program is not erased. This also implies that it is possible to have many programs
with the same name in the same bank.

3.3 The Bank Manager

Banks and Programs can be edited using the Bank Manager. The manager window is displayed
by clicking on the Manager button located above the Bank display. It is closed by clicking again
on the same button. On the left of the window, one finds the list of banks. Clicking on a bank name
fills the list of programs located in the center of the window with the name of these included in the
selected bank.
A new bank can be created by clicking on the + button below the bank list. This opens the
Create New Bank window in which the name of the new bank can be entered. A bank can be
deleted by first selecting it in the bank list and then clicking on the - button. Be careful, this
command erases a bank and all the programs it contains; this operation is permanent and can not
be undone. In order to rename a bank, simply click on the Rename button and enter a new name.
12 Bank and Program Management

Figure 2: Bank and program manager window.

Banks and the information corresponding to each of its programs is stored in a simple text file
on your computer hard disk. In order to view these bank files, click on the Show Files button under
the bank list. On Windows, this command will open an Explorer window at the location where the
files are stored. On Mac OSX, the command has a similar effect and opens a Finder window. All
the bank file names follow the same format and begin with the bank name. These files can be used
for backups or to exchange presets with other users.
The list of programs included in the selected bank is displayed in the program list in the center
of the manager window. Presets are selected by clicking on their name which updates the program
information appearing on the right of the preset list. Program information includes the name of the
preset, its author and comments. This information can be updated by clicking on the corresponding
box which opens an edition window. Note that multiple presets can be updated simultaneously by
selecting more than one preset at once and clicking on a preset information box.
A multiple selection consisting of adjacent programs is obtained by holding down the Shift key
on the computer keyboard and then clicking on the name of the first program to be copied and then
the last one. A non-adjacent multiple selection is obtained by holding down the Ctrl/command
computer key and clicking on the name of the different programs to be copied. It is also possible
to select all programs at once by clicking on the Select All button at the bottom of the program list.
Programs can be copied to another bank by clicking on the Copy button. A program must first
be selected by clicking on its name on the program list; it is then copied by moving the mouse to
a given bank in the Bank list on the right and clicking on the bank name. The Move command is
activated by clicking on the Move button; it copies a preset to a new bank but also erases it in the
original bank. A multiple selection of programs can be used with the Copy and Move commands
Programs can be deleted from a bank by first selecting them and then clicking on the Delete
button. This will move the programs to a special bank called Trash which is located below the
regular list of banks. This means that deleted programs can always be recuperated as long as they
are not deleted from the Trash bank. The content of the Trash bank is viewed by clicking on its
3.4 Using MIDI Bank and Program Changes 13

name; the different programs can then be moved to the other banks as explained above. The Trash
bank can be emptied by clicking on the Empty Trash button which appears below the program list
when the Trash bank is selected. Be careful as this command can not be undone.

3.4 Using MIDI Bank and Program Changes

Banks and programs can be changed using MIDI bank and program change commands. For more
information on how to use these commands, please refer to sections 6.2.4 and 6.2.5.

3.5 Backups of Banks and Programs

User banks are stored on disk as simple text files located in the following folders:
On Mac OS:
/Users/[user name]/Library/Application Support/Applied Acoustics Systems/Ultra Analog Session
2/Banks
On Windows:
%AppData%\Applied Acoustics Systems\Ultra Analog Session 2\Banks
The bank files saved by Ultra Analog Session are named using the following convention:
[name of bank].UAS2 Bank
These file contain all the information corresponding to the programs they include. These files can
be displayed directly from Ultra Analog Session by opening the Bank manager and clicking on
the Show Files button. This will open an Explorer or Finder window on Windows or Mac OS
respectively at the right location.
The simplest way to create a backup of banks and programs is to make a copy on an external
media of the above mentioned folders. Individual banks can be backed-up by making copies of
individual bank files.

3.6 Exchanging Banks and Programs

Banks and programs can easily be shared with other Ultra Analog Session users. This operation
simply involves the exchange of the above mentioned user bank files. When a new bank file is
copied to the bank folder, it is automatically available to Ultra Analog Session.
Note that individual programs can not be exported. They always appear inside a bank file. If
you only wish to share a few programs, create a new bank, copy the programs you wish to exchange
to this bank and share the corresponding bank file.
14 Parameters

3.7 Restoring the Factory Library

If necessary, it is possible to restore the original factory library of banks and programs. The original
factory bank files are located in the following folders:
On Mac OS startup disk:
/Library/Application Support/Applied Acoustics Systems/Ultra Analog Session 2/Factory Library
On Windows 64-bit:
C:\Program Files (x86)\Applied Acoustics Systems\Ultra Analog Session 2\Factory Library
On Windows 32-bit:
C:\Program Files\Applied Acoustics Systems\Ultra Analog Session 2\Factory Library
Restoring the factory library simply involves copying the files contained in these folders and
pasting them in the user bank folders listed in Section 3.5. The user bank folders can be opened
directly in an Explorer or Finder window, on Windows and Mac OS respectively, or by using the
Show Files command directly from the Ultra Analog Session bank manager.
Note that if you have bank files with the original factory bank names in your user bank folder,
they will be replaced by the original factory files. This means that you will lose programs that you
would have modified or created in these banks. This operation must therefore be done with caution
and it is recommended that you make copies or rename your user banks before proceeding with the
restore.

4 Parameters

This section can be used as a reference for the different controls appearing on the Ultra Analog
Session graphical interface. We begin by describing the behavior of the different types of controls
appearing on the interface and then describe the parameters of each module of the synthesizer.

4.1 General Functioning of the Interface

4.1.1 Knobs

Most of the synthesizer parameters are adjusted knobs and sliders. A specific control is selected
by clicking on it. A coarse adjustment is obtained by click-holding the parameter and moving the
mouse, or the finger on a track pad, either upwards and downwards or leftwards and rightwards.
The value of the parameter replaces its label while it is being adjusted.
Fine adjustment of a control is obtained by holding down a modifier key of the computer
keyboard (Shift, Ctrl, Command or Alt key) while adjusting the parameter. Double clicking on a
knob brings it back to its default value when available.
4.2 The Mode Module 15

4.1.2 Switches

Switches are turned on or off by clicking on them. They are used to activate or deactivate modules
and the sync feature of the Arpeggiator module.

4.1.3 Drop-down Menus

Clicking on black display controls reveals a drop-down menu with a set of possible settings for the
control. Adjustment of the parameter is obtained by clicking on a selection.

4.1.4 Modulation Signals

Different parameters can be modulated by the signal from the envelope generators and the LFO
modules. Modulation signals are controlled with small gain knobs located on the left of the corre-
sponding modulated parameters. The amplitude of the modulation is zero when the knob is centred.
It is increased by moving it from its middle position clockwise or anti-clockwise. When turning it
anti-clockwise, the phase of the modulating signal is inverted while it is preserved when moving it
clockwise.

4.1.5 Scaling

The size of the graphical interface can be adjusted by click-dragging the handle in its lower right
corner. While resizing the interface the zoom factor is displayed in the upper left corner of the
interface. This zoom factor can always be displayed by positioning the mouse on this corner. When
clicking on the zoom factor, a drop-down menu with specific size ratios is displayed. Selecting a
value resizes the interface automatically to that ratio. Note that this resize feature is only available
for 64-bit versions of the program.

4.2 The Mode Module

The Mode module is used to control how the synthesizer voices respond
to the events coming from an external MIDI keyboard or from a MIDI se-
quencer. When the switch is in the Mono position, the synthesizer is in
monophonic mode allowing one to play only one note at a time. In the Mono
Glide position, the synthesizer is still in monophonic mode but the pitch
slides between notes rather than changing immediately from note to note. In
the Poly position, the synthesizer is in polyphonic mode, allowing one the
play chords. In the Arp position, the Arpeggiator module is switched on and
notes are played sequentially depending on the settings of the Arpeggiator module. In the Arp
Glide, the arpeggiator is active and the pitch slides between notes as in the Mono Glide case.
16 Parameters

4.3 Unison

The unison mode allows one to play two voices for each note played on the keyboard. This mode
creates the impression that more than one instrument are playing the same note together, adding
depth to the sound.

In the Fifth and Octave positions, the second voice is one fifth or one
octave above the note played respectively. In the Subtle position, the second
voice plays the same note as the first one but it is slightly detuned resulting
in a slow beating effect. In the intense position, the second note also plays
the same note as the first one but the detuning between both voices is more
important resulting in a richer sound with a rapid beating effect.

4.4 The Arpeggiator Module

The Arpeggiator module allows one to play sequentially all the notes that
are played on the keyboard. In other words, arpeggios are played rather than chords. The modules
allows one to produce a wide range of arpeggios and rhythmic patterns and to sync the effects to
the tempo of an external sequencer.

Arpeggio Patterns

The arpeggio pattern is set by the combination of the value of the Range,
and Order controls. The Range control is used to select the number of oc-
taves across which the pattern is repeated. When the range is set to 0, there is
no transposition and only the notes currently depressed are played. If set to a
value between -2 and 2, the notes played are transposed and played sequen-
tially, over a range of one or two octaves. The direction of the transposition
depends on the sign of the Range value with downwards transposition for
negative values and upwards transposition for positive ones. The Order con-
trol sets the order in which the notes are played, therefore determining the
arpeggio pattern. When set to Forward, the notes are played from the lowest
to the highest. When set to Backward the notes are played from the highest
to the lowest. In the two last modes, RnRx (Rock and Roll exclusive) and
RnRi (Rock and Roll inclusive), the notes are played forward from the low-
est to the highest and then backward from the highest down to the lowest.
When using the RnR exclusive mode, the highest and the lowest notes are not
repeated when switching direction but in RnR inclusive mode these notes are repeated.
4.5 The Oscillator Module 17

Rhythmic Patterns

Rhythmic patterns can be added to the arpeggio pattern by using the 16-step Pattern display. Notes
are played as the step display is scanned and the corresponding step is selected (red button on).
Notes are played regularly when all the steps of the display are turned on and rhythmic patterns
are created by selecting only certain steps. The arrow button below each step is used to fix looping
points from which the rhythmic pattern starts being played again from the beginning.

Rate and Synchronization

When Ultra Analog Session is launched in standalone mode the tempo of the arpeggiator, in bpm,
is set by using the Rate knob. The tempo can also be adjusted by clicking at the desired tempo on
the Tap tempo pad of the module. Once the new tempo is detected, the value of the Rate knob is
automatically adjusted.
When using Ultra Analog Session in plugin mode, the Tap tempo pad is replaced by a Sync
switch. In its on position, the rate is synchronized with that of the host sequencer. When switched
off, the tempo is determined by the value of the Rate knob.
The rhythmic value of each step is set using the Steps parameter. Values range between a
quarter note and a thirty-second note with binary and ternary beat division options. One can then
fix the metric of the pattern by setting the loop point of the step display appropriately.

4.5 The Oscillator Module

The Oscillator module is the sound source of Ultra Analog Session. It is based on a square wave
generator with pulse width adjustment and hard sync feature allowing for a rich spectrum of sounds.
The Oscillator module is implemented using precise modeling algorithms rather than wave tables
providing alias free waveforms.
The pulse width of the rectangular wave is controlled using the PW knob. The width of the
pulse varies from 4% in its leftmost position to 50% in its rightmost position or in other words to a
perfectly square wave and therefore a spectrum containing only odd harmonics.

Synchronization

The Oscillator module features a hard synchronization mode. Synchronization involves a master
and a slave oscillator. In this mode, the signal from the slave Oscillator is reset, or in other words
18 Parameters

Figure 3: Choice of wave forms provided by the Oscillator module.

Figure 4: Synchronization of the oscillator.

restarted, at the beginning of each period of the waveform of the master oscillator which therefore
acts as a master clock as shown in Figure 4.
The perceived pitch of the final output of the oscillator module is the same as that of the master
oscillator while the frequency of the slave or synced oscillator only affects the harmonic content
4.6 The Filter Module 19

and therefore the timbre of the resulting signal. The frequency of this slave oscillator is adjusted
using the Sync knob and its value is presented as a ratio between the frequency of the slave and that
of the master oscillator. In its leftmost position, this ratio has a value of 1 which is equivalent to
deactivating the synchronization mode. The ratio, or frequency of slave oscillator is increased by
turning this knob clockwise.
The ratio value can further be modulated by an LFO with a triangular waveform. The amplitude
of the modulation is controlled using the LFO knob. When in its center position, the amplitude is
zero and there is no modulation. The depth of the modulation is increased by turning the knob
to the left or right. When turned anti-clockwise, the slope of the modulation is negative while it
is positive when turned clockwise. The frequency of the modulation is adjusted using the Rate
slider. A light modulation results in an effect similar to a vibrato or a pulse width modulation while
a deep modulation is close to an aggressive filter sweep effect. Note that the LFO waveform is
automatically re-trigged when a new note is played except when the playing mode is set to Arp or
Arp Glide. When using the Mono Glide mode, the signal from the LFO module is only re-trigged
if a note is not played legato.

4.6 The Filter Module

Ultra Analog Session is equipped with a 12dB/oct low-pass resonant fil-

ter. A low-pass filter is used to remove the higher spectral components of
the signal while leaving the lower components unchanged. The frequency at
which attenuation begins to take effect is called the cutoff frequency. In a
resonant filter, frequencies located around the cutoff frequency can also be
emphasized by an amount called the quality factor or Q-factor of the filter as
illustrated by Figure 5. The higher the Q-factor, the louder and sharper the
response of the filter around the cutoff frequency. When the Q-factor is set
to 1 (Q knob fully turned to the left), there is no emphasis around the cutoff
frequency and the attenuation is -3dB at the cutoff frequency. High values of
the of the resonance result in interesting saturation effects.
The resonance or cutoff frequency of the filters is adjusted with the Fre-
quency knob while the amount of resonance or Q-factor is controlled with
the Resonance knob. The value of the Frequency parameter corresponds to
the value of the cutoff frequency when a middle C note is played (MIDI note
number 60). The cutoff frequency is then automatically modulated depending on the note played
on the keyboard with increasing values for notes above middle C and a lower value for notes below
middle C.
The cutoff frequency of the filter can be modulated by an envelope generator creating filter
sweeps effects. The amplitude of this modulation is controlled using the Envelope parameter.
There is no modulation when this knob is centred. The depth of the effect is increased by turning
the knob to the left or to the right. When turned anti-clockwise the filter sweep starts at a frequency
below the cutoff frequency while it starts above the cutoff frequency when turned clockwise. Note
20 Parameters

Figure 5: Frequency response of the low-pass filter.

that this knob can be set to its center frequency by double-clicking on it. The Decay slider is used
to adjust the decay time of the envelope.

4.7 The Amp Module

After filtering, the signal is routed to an amplifier in order to add an amplitude envelope to the
sound. The envelope is generated through the use of a standard ADSR (attack, decay, sustain,
release) module with exponential segments.

Figure 6: Response curve of an envelope generator. Broken line: exponential, full line: linear.
4.8 The Effect Module 21

The ADSR module generates a four segment envelope: attack, decay, sustain,
release as illustrated in 6. The attack time is adjusted using the Attack knob and
controls how long the envelope takes to reach its peak amplitude. In its leftmost
position, attacks are extremely short and smoother attacks are obtained by turning
the knob clockwise. The decay time is the time taken by the envelope to go from its
peak level reached at the end of the attack phase to the sustain level. It is controlled
using the Decay knob. The sustain phase of the envelope generator lasts from
the end of the decay phase until the key is released. The level of the envelope is
controlled using the the Sustain knob. In its leftmost position, the sustain level is
zero and there is no sustain phase while fully turned to the right, the sustain level is
set to the peak value of the envelope and there is therefore no decay phase. When
the key is released, the envelope generator toggles to the release phase and the
envelope signal decreases from the value at the end of the sustain phase to zero in
a time set by the Release knob.
Note that the envelope is triggered every time a new note is played except when
notes are played legato or when the Mono Glide or Arp Glide modes are used.

4.8 The Effect Module

The Effect module allows one to process and shape the signal from the synthesizer before sending
it to the output. The active effect is selected using the Type drop-down menu and options include,
chorus, delay, distortion, equalizer, flanger, phaser and reverb. The controls appearing on the
module depend on the choice of effect. Note that the Effect module can be turned on or off by
using the green switch in the upper right corner of the module.

4.8.1 Chorus

The chorus effect is used to make a source sound like many similar sources played in unison. It
simulates the slight variations in timing and pitch of different performers executing the same part.
The effect is obtained by mixing the original signal with delayed version obtained from the output
of delay lines as shown in Figure 7. In the case of a chorus effect, the length of the delay lines must
be short in order for the delayed signals to blend with the original signal rather than be perceived as
a distinct echo. The length of the delay line can be modulated introducing a slight perceived pitch
shift between the voices.
22 Parameters

Figure 7: Chorus module.

Tuning

The amount of modulation of the length of the delay lines is adjusted

using the Depth slider. In its left position, there is no modulation and the
length of the delay lines remains constant. As the slider is moved to the
right, the length of the delay line starts to oscillate by an amount proportional
to the value of this parameter thereby increasing the amount by which the
different voices are detuned. The frequency of the modulation is fixed with
the Rate slider.
The Spread slider is used to adjust the amount of dispersion of the dif-
ferent voices in the stereo field. When in its leftmost position, there is an
equal amount of left and right output signal on each channel. In other words
the signal is the same on both channels. In its rightmost position, there is
complete separation between the channels, the left output from the chorus is
only sent to the left channel while the right output of the chorus is only sent
to the right channel. Finally, the Mix slider allows one to mix the dry and wet
signals. In its leftmost position, there is no output signal from the chorus and
one only ears the dry input signals. In its rightmost position, one only ears the wet signal from the
chorus module. In its center position, there is an equal amount of dry and wet signal in the output
signal from the module.
4.8 The Effect Module 23

4.8.2 Delay

The Delay module consists in a stereo feedback loop with a variable

delay in the feedback. It is used to produce an echo effect when the delay
time is long (greater than 100 ms) or to color the sound when the delay time
is short (smaller than 100 ms).
The Delay slider is used to adjust the amount of delay, in seconds, intro-
duced by the effect. Pushing this slider to the right increases the delay. The
Feedback parameter is a gain factor, varying in the range between 0 and 1,
applied to the signal at the end of the delay lines. It controls the amount of
signal that is re-injected in the feedback loop. In its leftmost position, the
value of this parameter is 0 and no signal is re-introduced in the delay line
which means that the signal is only delayed once. Moving this slider to the
right increases the amount of signal re-injected at the end of the feedback
loop and therefore allows one to control the duration of the echo for a given
delay time. In its rightmost position, the gain coefficient is equal to 1 which
means that all the signal is re-injected into the feedback loop and that the
echo will not stop.
The Pan slider is used to balance the input signal between the left and right channels. In its
leftmost position, signal is only fed into the left delay line and one hears clearly defined echo
first from the left channel and then from the right channel and so on. In its rightmost position,
the behavior is similar but with the first echo coming from the right channel. These two extreme
position correspond to the standard ping pong effect but a a less extreme behavior can be obtained
by choosing an intermediate position. In particular when the Pan knob is in its center position, an
equal amount of signal is sent in both channels.
The output signal from the Delay module can include a mix of input signal (dry) and delayed
signal (wet). The Wet slider is used to adjust the amplitude of the wet component in the final
output. The amplitude is increased by moving the slider to the right from no signal to an amplitude
of +6dB.

4.8.3 Distortion

The distortion effect colors the sound by the addition of overtones in the spectrum. In the time-
domain, this is obtained by limiting or clipping the amplitude of the input signal of the module.
The Drive parameter is a gain control acting on the input signal. This parameter allows one
to adjust the amount of distortion introduced in the signal by controlling how rapidly the signal
reaches the non-linear portion of the distortion curve applied on the signal. In its leftmost position,
the amplitude of the input signal is reduced by -6 dB; moving this slider to the right allows one to
increase its amplitude.
24 Parameters

The Tone slider is used to adjust the color of the signal after the distortion
algorithm has been applied. In its leftmost position, high frequencies are
attenuated in the signal while in its rightmost position low frequencies are
filtered out from the signal. In its center position, the signal is left unchanged.
The Volume parameter is a gain control acting on the amplitude of the
distorted signal, the amplitude increasing when moving the slider rightward.
Finally, the Mix slider allows one to control the amount of dry and wet (dis-
torted) signal in the final output signal from the Distortion module. In its
leftmost position, there is only dry signal in the output while in its rightmost
position one only hears the distorted signal. In its center position, there is an
equal amount of dry and wet signal in the output.

4.8.4 Equalizer

The Equalizer effects provides equalization over the low, mid, and high
frequency bands. It is composed of a low cut filter, a low shelf filter, a peak
filters, and a high shelf filter in series.
The low cut filter is a simple 12 dB/oct high pass filter. The cutoff fre-
quency of the filter is set using the Low Cut slider and can take values be-
tween 0 and 5 Hz and 2 kHz.
The functioning of the low shelf filter is depicted in Figure 8. The filter
applies a gain factor to low frequency components located below a cutoff
frequency while leaving those above unchanged. The cutoff frequency of
this filter is set to 130.81 Hz (C3) and the Low slider is used to adjust the
gain factor applied to the signal. In its center position there is no attenuation
(0 dB). Moving it to the right boosts the amplitude of low frequencies while
moving it to the left reduces it.
The high frequency content of the signal is controlled with a high shelf
filter that works in the opposite manner as the low shelf filter as illustrated in Figure 8. The filter
applies a gain factor to components located above a cutoff frequency while leaving those below
unchanged. The cutoff frequency of this filter is set to 523.25 Hz (C5) and the gain factor applied
to the signal is adjusted using High slider. In its center position there is no attenuation (0 dB).
Moving it to the right boosts the amplitude of high frequencies while moving it to the left reduces
it.
The EQ module features a peak filter allowing one to shape the signal in a frequency band as
illustrated in Figure 9. The filters apply a gain factor to frequency components in a band located
around the cutoff frequency of the filters. This cutoff frequency is set to 261.63 Hz (C4) and the
gain factor applied a this frequency is controlled by the Mid slider. When in its center position
there is no attenuation (0 dB). Moving it to the right boosts the amplitude of frequencies located
around the cutoff frequency while turning it to the left reduces it.
4.8 The Effect Module 25

Figure 8: Low and high shelf filters.

Figure 9: Peak filter.

4.8.5 Flanger

The Flanger module implements the effect known as flanging which colors the sound with a false
pitch effect caused by the addition of a signal of varying delay to the original signal.
26 Parameters

Figure 10: Flanger algorithm.

The algorithm implemented in this module is shown in Figure 10. The

input signal is sent into a variable delay line. The output of this delay is then
mixed with the dry signal and re-injected into the delay line with a feedback
coefficient.
The effect of the Flanger module is to introduce rejection in the spec-
trum of the input signal at frequencies located at odd harmonic intervals of
a fundamental frequency as shown in Figure 11. The location of the fun-
damental frequency f 0 and the spacing between the valleys and peaks of
the frequency response is determined by the length of the delay line (f 0 =
1/(2delay)), the longer the delay, the lower is f 0 and the smaller the spacing
between the harmonics while decreasing the delay increases f 0 and hence
the distance between the harmonics.
The amount of effect is determined by the ratio of wet and dry signal
mixed together as shown in Figure 12. As the amount of wet signal sent
to the output is increased, the amount of rejection increases. Finally, the shape of the frequency
response of the Flanger module is also influenced by the amount of wet signal re-injected into
the feedback loop as shown in Figure 13. Increasing the feedback enhances frequency components
least affected by the delay line and located at even harmonic intervals of the fundamental frequency.
As the feedback is increased, these peaks become sharper resulting in an apparent change in the
pitch of the signal.
The delay length, in milliseconds, is adjusted with the Delay slider. The length of this delay
can be modulated by a certain amount depending on the adjustment of the Depth slider. In the left
position, there is no modulation and the length of the delay line remains constant. As the slider is
moved towards the right, the length of the delay line starts to oscillate with increasing amplitude
and at a frequency fixed with the Rate slider. Finally, the Mix slider determines the amount of dry
4.8 The Effect Module 27

Figure 11: Frequency response of a Flanger module. Effect of the length of the delay line.

Figure 12: Effect of the mix between wet and dry signal on the frequency response of a Flanger
module

Figure 13: Effect of the amount of feedback on the frequency response of a Flanger module.
28 Parameters

and wet signal in the output signal from the module. When in its leftmost position, only dry signal
is sent to the output, in its center position, there is an equal amount of dry and wet signal in the
output signal while in its rightmost position, only wet signal is sent to the output.

4.8.6 Phaser

The Phaser module implements the effect known as phasing which colors a
signal by removing frequency bands from its spectrum. The effect is obtained by
changing the phase of the frequency components of a signal using an all-pass filter
and adding this new signal to the original one.
The algorithm implemented in this module is shown in Figure 14. The input
signal is sent into a variable all-pass filter. This wet signal is then mixed down
with the original dry signal. A feedback line allows the resulting signal to be re-
injected into the filter. The effect of the Phaser module is to introduce rejection in
the spectrum of the input signal depending on the tuning of the filter.

Figure 14: Phaser algorithm.

The all-pass filter modifies a signal by delaying its frequency components with a delay which
increases with the frequency. This phase variations introduce a certain amount of cancellation when
this wet signal is mixed down with the original dry signal as shown in Figure 15. The rejection is
maximum when the phase delay is equal to 180 degrees and a given component is out of phase with
that of the original signal. The amount of effect is determined by the ratio of wet and dry signal
mixed together as shown in Figure 15. As the amount of wet signal sent to the output is reduced, the
amount of rejection increases. The shape of the frequency of the Phaser module is also influenced
by the amount of wet signal re-injected into the feedback loop. Increasing the feedback enhances
4.8 The Effect Module 29

frequency components least affected by the all-pass filter. As the feedback is increased, these peaks
become sharper. The functioning of the Phaser is very similar to that of the Flanger module. The
filtering effect is different however, since the Phaser module only introduces rejection around a
limited number of frequencies which, in addition, are not in an harmonic relationship.

Figure 15: Frequency response of a Phaser module. Effect of the mix between wet and dry signal
on the frequency response.

The location of the first notch in the frequency response of the module can be modulated by an
amount controlled with the Depth slider. In its leftmost position, the location of the first notch is
fixed but it starts to oscillate by an amount which increases as the Depth slider is moved to the right.
The frequency of the modulation is controlled using the the Rate slider. The feedback parameter is
used to fix the amount of wet signal re-injected into the delay. Finally, the Mix slider determines
the amount of dry and wet signal sent to the output. When this slider is adjusted in the left position,
only dry signal is sent to the output, in its center position, there is an equal amount of dry and wet
signal in the output and in the right position, only wet signal is sent to the output.
30 Parameters

4.8.7 Reverb

The Reverb effect is used to recreate the effect of reflections of sound

on the walls of a room or hall. These reflections add space to the sound and
make it warmer, deeper, as well as more realistic since we always listen to
instruments in a room and thus with a room effect.

Impulse Response of a Room

The best way to evaluate the response of a room is to clap hands and to
listen to the resulting sound. Figure 16 shows the amplitude of the impulse
response of a room versus time. The first part of the response is the clap
itself, the direct sound, while the remaining of the response is the effect of
the room which can itself be divided in two parts. Following the direct sound,
one can observe a certain amount of echoes which gradually become closer
and closer until they can not be distinguished anymore and can be assimilated
to an exponentially decaying signal. The first part of the room response is
called the early reflexion while the second is called the late reverberation.
The total duration of the room response is called the reverberation time (RT).

Figure 16: Impulse response of a room.

Adjusting the room effect

The size of a room strongly affects the reverberation effect. The Size parameter is used to choose
between the Studio, Club, Hall and Large Hall settings each reproducing spaces of different vol-
umes from smaller to larger.
The duration of the reverberation time depends on both the size of the room and the absorption
of the walls, which is controlled with the Decay slider. In a real room the reverberation time is not
4.9 Pitch Wheel 31

constant over the whole frequency range. As the walls are often more absorbent in the very low
and in the high frequencies the reverberation time is shorter for these frequencies. The absorption
level of high frequencies is adjusted with the help of the High slider.
The last parameter which affects our listening experience in a room, is the distance between
the sound source and the listener. While the room response is quite constant regardless of the
position of the source and the listener, the direct sound (the sound which comes directly from the
source) depends strongly on the position of the listener. The farther we are from the sound source
the quieter is the direct sound relatively to the room response. The ratio between the direct sound
and the room response is adjusted with the Mix slider which in other words is used to adjust the
perceived distance between the source and the listener. In its leftmost position, only the direct
sound is heard while when fully turned to the right, one only hears the room response.

4.9 Pitch Wheel

The MIDI pitch wheel allows one to vary the pitch of the note played. The pitch wheel can be
moved with the mouse but it is also automatically connected to the pitch wheel signal received
from your MIDI keyboard.
The range of the pitch bend is 2 semi-tones up or down by default but can be changed. To adjust
the range of the pitch bend, open the MIDI configuration window by clicking on the MIDI button
located just below the MIDI led in the top part of the interface and use the Pitch Bend Range
drop-down menu to select the range in semi-tones.

4.10 Modulation Wheel

The modulation wheel is linked to the Amount parameter of the Vibrato module. It can be activated
on screen or from the modulation wheel of your MIDI controller (MIDI controller number 1). The
MW gain knob of the Vibrato module is used to control the sensitivity of the vibrato amplitude
to the modulation wheel. Note that other parameters can be linked to the modulation wheel using
MIDI links as explained in Section 6.2.2.

4.11 Ribbon

The lower part of this view includes a ribbon controller. The ribbon covers seven octaves and notes
are played when clicking on the ribbon. The ribbon is useful to test sounds when no MIDI keyboard
is connected to your computer.
32 Utility Section

5 Utility Section

The utility section is located at the top of the Ultra Analog Session interface and it includes im-
portant parameters and monitoring tools. For information on Banks and Programs please refer to
Chapter 3.

5.1 The MIDI LED

The MIDI LED is located on the left of the level-meter. The LED blinks when the synthesizer
receives MIDI signal. If the application is not receiving MIDI signal, make sure that the host
sequencer is sending MIDI to Ultra Analog Session. If you are running in standalone mode, make
sure that the MIDI controller you wish to use is well connected to your computer and that it is
selected as explained in Section 6.
Clicking on the MIDI button just below the MIDI led opens the MIDI configuration pop-up
window from which one can adjust parameters such as the pitch bend range, enable bank and pro-
gram changes and manage the MIDI map used by Ultra Analog Session as explained in Chapter 6

5.2 Polyphony

Ultra Analog Session always function in polyphonic mode with 16 voices of polyphony.

5.3 Tuning

The Tune control, located to the right of the MIDI LED, is used to transpose the frequency of the
keyboard. This control is composed of two numbers separated by a dot. The first number indicates
a value in semi-tones while the second one indicates a value in cents (one hundredth of a semi-
tone). The amount of transposition can be adjusted by click-dragging upward or downward on the
semi-tone and cent controls. Double clicking on these controls brings back their value to zero.
When the value of the Tune parameters is set to 0.00, the frequency of notes are calculated relative
to A4 440Hz.
An interesting feature of Ultra Analog Session is that it can be tuned using different tempera-
ments using Scala micro-tuning files. Temperament files are loaded by clicking on the Tune button
which opens the Tuning pop-up window and displays the list of available tuning temperament files
5.4 History and Compare 33

available. By default, Ultra Analog Session is set to Equal Temperament but other temperament
files can be added to the list by copying them to the following folders:
On Mac OS: /Users/[user name]/Library/Application Support/Applied Acoustics Systems/Scala
Tunings/ On Windows: %AppData%\Applied Acoustics Systems\Scala Tunings\
These folders can be displayed directly from Ultra Analog Session by clicking on the Show
Tuning Files button at the bottom of the Tuning pop-up window.
Selecting a Scala file in the list automatically triggers the loading of the corresponding temper-
ament. The reference note that will be used as the base note for the scale described in the Scala file
can be set using the Reference Note control appearing at the bottom of the Tuning window. The
frequency of this reference note is calculated relative to the settings of the Tune control.

5.4 History and Compare

The History control allows one to go back through all the modifications that were made to programs
since the application was started. In order to travel back and forth in time, use the left and right-
pointing arrows respectively. The application will switch between different program states and
indicate the time at which they were modified.
The Compare button, located above the Program display, is used to switch between Edit and
Compare mode. This button is visible only once a modification is applied to a given program. It
allows one to revert to the original version of a program in order to compare it with the current
version. When in Compare mode, edition is blocked and it is therefore not possible to modify any
parameter. The Compare mode must then be switched off by clicking on the Compare button in
order to resume edition.

5.5 Volume

The Volume knob is the master volume of the application. It is used to adjust the overall level of
the output signal from the synthesizer. General level is increased by turning the knob clockwise.

5.6 Level Meter

The level meter allows one to monitor peak and RMS (root means square) level of the left (L) and
right (R) output channels from the synthesizer. As a limiter is located at the output of Ultra Analog
Session, it is important to make sure that the amplitude of the signal remains within values that
ensure that no distortion is introduced in the signal at the output.
The 0 dB mark on the level meter has been adjusted to correspond to -20 dBFS (full scale). This
means that at that level, the signal is -20 dB below the maximum allowed value. This 0 dB level
mark should typically correspond to playing at mezzo forte (moderately loud) level. This ensures
a headroom of 20 dB which should be more than enough to cover the dynamics of most playing
situations and therefore guarantee that no additional distortion is added in the output signal.
34 Audio and MIDI Settings

A peak value mark allows one to follow the maximum level values reached by the output signal.
The limiter is triggered when this mark enters the red zone of the level meter (17 dB) and it remains
active while the side vertical bars at the top of the lever meter are switched on.

5.7 The About Box

The About box is open by clicking on the chevrons located at the very top of the interface or on
the product or company logo. The box is closed by clicking again on the chevrons or outside the
box. Useful information is displayed in this box such as the program’s version number, the serial
number that was used for the authorization and the the email address that was used for registration.
The box also includes a link to the pdf version of this manual.

6 Audio and MIDI Settings

This chapter explains how to select and configure Audio and MIDI devices used by Ultra Analog
Session. Audio and MIDI configuration tools are accessed by clicking on the Audio Setup button
located in the lower left corner of the Ultra Analog Session interface and the MIDI button located
just below the MIDI led in upper part of the interface.
Note that in plug-in mode the audio and MIDI inputs, sampling rate, and buffer size are set by
the host sequencer.

6.1 Audio Configuration

6.1.1 Selecting an Audio Device

Audio configuration tools are available by clicking on the Audio Setup button located in the lower
left corner of the Ultra Analog Session interface. The Audio Setup dialog first allows you to select
an audio output device from those available on your computer. Multi-channel interfaces will have
their outputs listed as stereo pairs.
On Windows, the audio output list is organized by driver type. The device type is first selected
from the Audio Device Type drop-down list. If you have ASIO drivers available, these should be
selected for optimum performance. The Configure Audio Device button allows you to open the
manufacturer’s setup program for your audio interface when available.
Once the audio input has been selected, you can then select a sampling rate and a buffer size
from those offered by your audio interface.

6.1.2 Latency

The latency is the time delay between the moment you send a control signal to your computer
(for example when you hit a key on your MIDI keyboard) and the moment when you hear the
6.2 MIDI Configuration 35

effect. Roughly, the latency is equal to the duration of the buffers used by the application and
the sound card to play audio and MIDI. To calculate the total time required to play a buffer, just
divide the number of samples per buffer by the sampling frequency. For example, 256 samples
played at 48 kHz represent a time of 5.3 ms. Doubling the number of samples and keeping the
sampling frequency constant doubles this time while changing the sampling frequency to 96 kHz
and keeping the buffer size constant reduces the latency to 2.7 ms.
It is of course desirable to have as little latency as possible. Ultra Analog Session however
requires a certain amount of time to be able to calculate sound samples in a continuous manner.
This time depends on the power of your computer, the preset played, the sampling rate, and the
number of voices of polyphony used. Note that it literally takes twice as much CPU power to
process audio at a sampling rate of 96 kHz as it would to process the same data at 48 kHz, simply
because you need to calculate twice as many samples in the same amount of time.
Depending on your machine you should choose, for a given sampling frequency, the smallest
buffer size that allows you to keep real-time for a reasonable number of voices of polyphony.

6.2 MIDI Configuration

6.2.1 Selecting a MIDI Device

The list of available MIDI inputs appears at the bottom of the Audio Setup dialog. Click on the
Audio Setup button located in the lower left corner of the Ultra Analog Session interface and then
click on the checkbox corresponding to any of the inputs you wish to use.

6.2.2 Creating MIDI Links

Every control on the Ultra Analog Session interface can be manipulated by an external MIDI con-
troller through MIDI control change assignments. In most cases this is much more convenient than
using the mouse, especially if you want to move many controllers at once. For example, you can
map the motion of a knob on the interface to a real knob on a knob box or to the modulation wheel
from your keyboard. As you use the specified MIDI controllers, the controls move on the Ultra
Analog Session interface just as if you had used the mouse.
In order to assign a MIDI link to a controller:

• On the Ultra Analog Session interface, right-click/Control-click on a control (knob, button)

and select the MIDI Learn command.
• Move a knob or slider on your MIDI controller (this can be a keyboard, a knob box, or
any device that sends MIDI). This links the control of Ultra Analog Session to the MIDI
controller you just moved.

To deactivate a MIDI link, simply righ-click/Control-click on the corresponding control on the

Ultra Analog Session interface and select the MIDI Forget command.
36 Audio and MIDI Settings

6.2.3 Creating a default MIDI Map

It is possible to define a a set of MIDI links, called a MIDI map, that will be loaded automatically
when Ultra Analog Session is launched. Once you have defined a set of MIDI links that you wish to
save, click on MIDI button to open the MIDI configuration window and click on the Save Current
as Default button.
If you make changes to MIDI links after opening the program and wish to revert to the default
MIDI map click on MIDI button to open the MIDI configuration window and click on the Load
Default button.
If you wish to deactivate all the MIDI links at once open the MIDI configuration window and
click on the Clear MIDI Map button.

6.2.4 MIDI Program Changes

Ultra Analog Session responds to MIDI program changes. When a program change is received, the
current program is changed to the program having the same number as that of the program change
message in the currently loaded bank.
If you do not wish Ultra Analog Session to respond to MIDI program changes, open the MIDI
configuration window by clicking on the MIDI button and uncheck the Enable Program Changes
option.

6.2.5 MIDI Bank Changes

In general, MIDI bank numbers are coded using two signals: the MSB (most significant byte) and
LSB (least significant byte) transmitted using MIDI CC (continuous controller) number 0 and 32
respectively. The way these signals are used differs with different manufacturers.
In the case of Ultra Analog Session, the value of the MSB signal is expected to be zero while
the value of the LSB signal represents the bank number. Banks are therefore numbered from 0 to
127 with this number corresponding to the position of a bank within the list of banks as displayed
by the Bank manager (see Section 3.3). For example, an LSB value of 0 corresponds to the first
bank in the bank list while an LSB value of 10 corresponds to the eleventh bank in the list. Note that
a bank change only becomes effective after the reception of a new MIDI program change signal.
If you do not wish Ultra Analog Session to respond to MIDI bank changes, open the MIDI
configuration window by clicking on the MIDI button and uncheck the Enable Bank Changes
option.

6.2.6 Pitch bend

The MIDI pitch wheel allows one to vary the pitch of Ultra Analog Session. The pitch wheel can
be moved with the mouse but it is also automatically connected to the pitch wheel signal received
Using Ultra Analog Session as a Plug-In 37

from your MIDI keyboard.

The range of the pitch bend is 2 semi-tones up or down by default but can be changed. To adjust
the range of the pitch bend, open the MIDI configuration window by clicking on the MIDI button
located just below the MIDI led in the top part of the interface and use the Pitch Bend Range
drop-down list to select the range in semi-tones.

6.2.7 Modulation wheel

Ultra Analog Session responds to MIDI modulation (MIDI controller number 1). For more details,
please refer to Section 4.10.

7 Using Ultra Analog Session as a Plug-In

Ultra Analog Session is available in VST, RTAS, AAX and Audio Units formats and integrates
seamlessly into the industry most popular multi-track recording and sequencing environments as a
virtual instrument plug-in. Ultra Analog Session works as any other plug-in in these environments
so we recommend that you refer to your sequencer documentation in case you have problems
running it as a plug-in. We review here some general points to keep in mind when using a plug-in
version of Ultra Analog Session.

7.1 Audio and MIDI Configuration

When Ultra Analog Session is used as a plug-in, the audio and MIDI ports, sampling rate, buffer
size, and audio format are determined by the host sequencer.

7.2 Automation

Ultra Analog Session supports automation functions of host sequencers. All parameters visible on
the interface can be automatized except for the Bank, Program and History commands.

7.3 Multiple Instances

Multiple instances of Ultra Analog Session can be launched simultaneously in a host sequencer.

7.4 Saving Projects

When saving a project in a host sequencer, the currently loaded program is saved with the project
in order to make sure that the instrument will be in the same state as when you saved the project
when you re-open it. Note that banks of programs are not saved with the project which implies that
38 License Agreement

if you are using MIDI program changes in your project, you must make sure that the bank you are
using in your project still exists on your disk when you reload the project. The programs must also
exist and be in the same order as when the project was saved.

7.5 Performance

Using a plug-in in a host sequencer requires CPU processing for both applications. The load on the
CPU is even higher when multiple instances of a plug-in or numerous different plug-ins are used.
To decrease CPU usage, remember that you can use the freeze or bounce to track functions of the
host sequencer in order to render to audio the part played by a plug-in instead of recalculating it
every time it is played.

8 License Agreement

IMPORTANT! CAREFULLY READ ALL THE TERMS AND CONDITIONS OF THIS AGREE-
MENT BEFORE OPENING THIS PACKAGE. OPENING THIS PACKAGE INDICATES YOUR
ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF YOU DO NOT AGREE WITH
THE TERMS AND CONDITIONS OF THIS AGREEMENT, PROMPTLY RETURN THE UN-
OPENED PACKAGE AND ALL COMPONENTS THERETO TO THE PARTY FROM WHOM
IT WAS ACQUIRED, FOR A FULL REFUND OF ANY CONSIDERATION PAID.
This software program, any printed materials, any on-line or electronic documentation, and any
and all copies of such software program and materials (the “Software”) are the copyrighted work
of Applied Acoustics Systems DVM Inc. (“AAS”), its subsidiaries, licensors and/or its suppliers.

1. LICENSE TO USE. The Licensee is granted a personal, non-exclusive and non-transferable

license to install and to use one copy of the Software on a single computer solely for the
personal use of the Licensee. Use of the Software is subject to this Agreement.

2. RESTRICTIONS ON USE. The Licensee may not nor permit third parties to (i) make copies
of any portion of the Software, other than as expressly permitted under this Agreement; (ii)
modify, translate, disassemble, decompile, reverse engineer or create derivative and/or com-
petitive products based on any portion of the Software; (iii) provide use of the Software in a
network, timesharing, interactive cable television, multiple CPU service bureau or multiple
user arrangement to users not individually licensed by AAS, other than as expressly permit-
ted by the terms of this license. The Software is licensed to you as a single product. Its
component parts may not be separated for use on more than one computer.

3. OWNERSHIP. AAS retains title to the Software, including but not limited to any titles,
computer code, themes, objects dialog concepts, artwork, animations, sounds, audio effects,
methods of operation, moral rights, any related documentation and “applets” incorporated
into the Software. AAS retains ownership of and title to all intellectual property rights in the
License Agreement 39

Software, underlying technology, related written materials, logos, names and other support
materials furnished either with the Software or as a result of this Agreement, including but
not limited to trade secrets, patents, trademarks and copyrights therein. Licensee shall not
remove or alter any copyright or other proprietary rights notices contained on or within the
Software and shall reproduce such notices on all copies thereof permitted under this Agree-
ment or associated documentation.
4. LIMITED WARRANTY. Except for the foregoing, THE SOFTWARE IS provided “AS IS”
without warranty or condition of any kind. AAS disclaims all warranties or conditions, writ-
ten or oral, statutory, express or implied, including but not limited to the implied warranties of
merchantable quality or fitness for a particular purpose, title and non-infringement of rights
of any other person. AAS does not warrant that THE SOFTWARE will meet the Licensee’s
requirements or that the operation of the software will be uninterrupted or ERROR-FREE.
5. LIMITATION OF LIABILITY. TO THE MAXIMUM EXTENT PERMITTED BY APPLI-
CABLE LAW, IN NO EVENT WILL AAS BE LIABLE TO THE LICENSEE OR ANY
THIRD PARTY FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, INCIDENTAL
OR EXEMPLARY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO
LOSS OF REVENUE OR PROFIT, LOST OR DAMAGED DATA, BUSINESS INTER-
RUPTION OR ANY OTHER PECUNIARY LOSS WHETHER BASED IN CONTRACT,
TORT OR OTHER CAUSE OF ACTION, EVEN IF AAS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, EXCEPT IN RELATION TO GROSS NEGLIGENCE
OR WILFUL BREACH OF THIS AGREEMENT BY AAS. NO AAS AGENT, REPRE-
SENTATIVE OR DEALER IS AUTHORIZED TO EXTEND, MODIFY OR ADD TO THIS
WARRANTY ON BEHALF OF AAS. THE TOTAL LIABILITY OF AAS FOR DAM-
AGES, WHETHER IN CONTRACT OR TORT, UNDER OR RELATED IN ANY WAY TO
THIS AGREEMENT SHALL BE LIMITED TO THE LICENSE FEES ACTUALLY PAID
BY LICENSEE TO AAS, OR IF NO FEES WERE PAID, AAS’ LIST PRICE FOR THE
SOFTWARE COVERED BY THIS LICENSE. THE EXCLUSION OF IMPLIED WAR-
RANTIES AND/OR THE LIMITATION OF LIABILITY IS NOT PERMITTED IN SOME
JURISDICTIONS, AND SOME OR ALL OF THESE EXCLUSIONS MAY THEREFORE
NOT APPLY.
6. TERMINATION. This License also shall extend to the Software and any updates or new
releases thereof obtained by the Licensee, if any, subject to any changes to this License made
by AAS from time to time and provided to the Licensee, provided AAS is under a separate
obligation to provide to Licensee such updates or upgrades and Licensee continues to have a
valid license which is in effect at the time of receipt of each such update or new release. This
License shall remain in effect until terminated. The Licensee may terminate this Agreement
at any time, upon notification to AAS. This Agreement will terminate immediately without
notice from AAS if the Licensee fails to comply with any provision of this License. Any
such termination by AAS shall be in addition to and without prejudice to such rights and
remedies as may be available, including injunction and other equitable remedies. Upon
receipt of notice of termination from AAS, the Licensee must (a) immediately cease to use
40 License Agreement

the Software; (b) destroy all copies of the Software, as well as copies of all documentation,
specifications and magnetic media relating thereto in Licensee’s possession or control; and
(c) return all original versions of the Software and associated documentation. The provisions
of Sections 1, 3, and 5 shall survive the termination of this Agreement.

7. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with
the laws of the Province of Quebec, without regard to the United Nations Convention On
Contracts for the International Sale of Goods and conflict of laws provisions, if applicable,
and the parties hereby irrevocably attorn to the jurisdiction of the courts of that province. Les
parties sont d’accord à ce que cette convention soit rédigée en langue anglaise. The parties
have agreed that this agreement be drafted in the English language.

8. SEVERABILITY. If any of the above provisions are held to be illegal, invalid or unenforce-
able, such provision shall be severed from this Agreement and this Agreement shall not be
rendered inoperative but the remaining provisions shall continue in full force and effect.

9. ENTIRE AGREEMENT. This Agreement is the entire agreement between AAS and the
Licensee relating to the Software and: (i) supersedes all prior or contemporaneous oral or
written communications, proposals and representations with respect to its subject matter; and
(ii) prevails over any conflicting or additional terms of any quote, order, acknowledgement,
or similar communication between the parties during the term of this Agreement except as
otherwise expressly agreed by the parties. No modification to the Agreement will be binding,
unless in writing and signed by a duly authorized representative of each party.

10. NON-WAIVER. No delay or failure to take any action or exercise any rights under this
Agreement shall constitute a waiver or consent unless expressly waived or consented to in
writing by a duly authorized representative of AAS. A waiver of any event does not apply to
any other event, even if in relation to the same subject-matter.
Index
about, 34 filter, 19
amplifier, 21 low-pass filter, 19
architecture, 10 fine tuning, 15
arpeggiator, 16 flanger, 22, 26
looping, 17
pattern, 17 hard synchronization, 18
rate, 17 help, 8, 9
rhythmic pattern, 17 history, 33
synchronization, 17
installation, 7
audio, 35
inteface
configuration, 8, 35
resize, 16
device, 35
interface, 15
latency, 35
drop-down menus, 15
auto-wah, 22
knobs, 15
backup, 13 numerical displays, 15
bank, 11 slider, 15
backup, 13 switches, 15
create, 11
knobs, 15
delete, 11
factory library, 14 latency, 35
rename, 11 level, 21
sharing, 13 level meter, 33
bank manager, 11 library
buffer size, 8, 35 restore, 14
limiter, 33
chorus, 22
low-pass filter, 19
coarse, 15
compare, 33 manual, 34
contact, 9 master volume, 33
cpu load, 32 micro-tuning, 32
MIDI, 35
default MIDI map, 36
bank change, 37
delay, 22, 23
configuration, 8, 36
distortion, 24, 33
device, 36
drop-down menus, 15
link map, 36
EQ, 24 links, 36
equalizer, 22, 24 pitch bend, 31, 37
program change, 11, 13, 37
factory library, 8 receiving, 32
42 INDEX

MIDI controller, 36 saving, 11

MIDI led, 32 sharing, 13
minimum system requirements, 6
mode, 16 resize, 16
modulation, 15 restore factory library, 14
modulation wheel, 31 reverb, 29
modules, 15 ribbon, 31
multi-effect, 22
sampling rate, 7, 8
chorus, 22
save, 11
delay, 23
save as, 11
distortion, 24
scala files, 32
equalizer, 24
scaling, 16
flanger, 26
signal flow, 10
phaser, 28 slider, 15
reverb, 29 standalone, 8
start-up, 8
notch filter, 22
switches, 15
numerical displays, 15
synchronization, 18
oscillator, 18 system requirements, 6
hard synchronization, 18
transpose, 32
parameters, 15 tremolo, 22
peak, 33 tuning, 32
phaser, 22, 28 unison, 16
physical modeling, 6 utility section, 32
pitch bend, 32, 37
pitch wheel, 31 vco, 18
plug-in, 9 voices, 32
audio configuration, 38 voltage controlled oscillator, 18
automation, 38 volume, 33
formats, 38 VU meter, 33
MIDI configuration, 38
multiple instances, 38 wah wah, 22
performance, 38
saving projects, 38
polyphony, 7, 32
programs, 8, 11
backup, 13
bank manager, 11
copy, 11
factory library, 14
move, 11