Scribd Logo
Upload

Welcome to Scribd!

  • 24 views

    H2 02 P2 GRS E.3 PRO 24003 Factory Acceptance Test Procedure (FAT) - Reply

    Uploaded by

    Rangga Seta
    The document is a factory acceptance test procedure for a generator set from Mitsubishi. It outlines tests to be conducted at various loads from 0% to 100% to check output, voltage, current, power factor, frequency, temperatures, speeds, flows, and pressures. Protective devices will also be tested, including emergency stop, low oil pressure, high temperature, and overspeed alarms and trip signals. Load tests will be performed from 10:00 to 10:55 in 5 to 20 minute intervals.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    H2 02 P2 GRS E.3 PRO 24003 Factory Acceptance Test Procedure (FAT) - Reply

    Uploaded by

    Rangga Seta
    24 views20 pages
    The document is a factory acceptance test procedure for a generator set from Mitsubishi. It outlines tests to be conducted at various loads from 0% to 100% to check output, voltage, current, power factor, frequency, temperatures, speeds, flows, and pressures. Protective devices will also be tested, including emergency stop, low oil pressure, high temperature, and overspeed alarms and trip signals. Load tests will be performed from 10:00 to 10:55 in 5 to 20 minute intervals.

    Original Title

    H2 02 P2 GRS E.3 PRO 24003 Factory Acceptance Test Procedure (FAT)_Reply

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document is a factory acceptance test procedure for a generator set from Mitsubishi. It outlines tests to be conducted at various loads from 0% to 100% to check output, voltage, current, power factor, frequency, temperatures, speeds, flows, and pressures. Protective devices will also be tested, including emergency stop, low oil pressure, high temperature, and overspeed alarms and trip signals. Load tests will be performed from 10:00 to 10:55 in 5 to 20 minute intervals.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    24 views20 pages

    H2 02 P2 GRS E.3 PRO 24003 Factory Acceptance Test Procedure (FAT) - Reply

    Uploaded by

    Rangga Seta
    The document is a factory acceptance test procedure for a generator set from Mitsubishi. It outlines tests to be conducted at various loads from 0% to 100% to check output, voltage, current, power factor, frequency, temperatures, speeds, flows, and pressures. Protective devices will also be tested, including emergency stop, low oil pressure, high temperature, and overspeed alarms and trip signals. Load tests will be performed from 10:00 to 10:55 in 5 to 20 minute intervals.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 20

    PUBLIC RESTRICTED CONFIDENTIAL SECRET

    H2-02 DATACENTER - PHASE 2


    PROJECT

    Project Name H2-02 DATACENTER PHASE 2


    Vendor Name PT. BERKAT MANUNGGAL ENERGI
    Purchase Order No #PO/DISM/24/01/0007
    Equipment Tag No

    Project Document No H2-02-P2-GRS-E3-PRO-24003

    DOCUMENT TITLE FACTORY ACCEPTANCE TEST PROCEDURE (FAT)

    DOCUMENT REVIEW STATUS

    CODE A Approved - With No Comments. Document is accepted as Final. Supplier shall proceed with manufacture. Any changes to
    the document shall require resubmission to Purchaser.

    CODE B Approved with Comment Incorporated . Work may proceed subject to incorporation of comments. Supplier may
    continue for puchase of material & manufacture pending full acceptance. A revised copy shall be returned for final acceptance.

    CODE C Rejected. Revise and Resubmit. WORK MAY NOT PROCEED.

    CODE D For Information Only. No further action required at time of submission.

    Clarify generator 12 hrs burn in test with DISM BOQ.

    Submission Record

    0 1-Feb-24 APPROVAL DD RS HT

    Rev.
    Date Purposes for Submission Prepared Checked Approved
    No

    DISM - H2-02-P2
    4
    4
    4
    4
    4
    4
    4
    4
    4

    2000
    4
    4
    4
    4
    4
    TEST RECORD OF MITSUBISHI GENERATOR SET
    Messrs

    MODEL :
    CUSTOMER : PROJECT No. :

    BAROMETRIC FUEL OIL SPECIFIC


    DIVISION TEST DATE WEATHER FUEL OIL LUB. OIL
    PRESS. GRAVITY
    FINE CLOUDY LIGHT OIL SAE 30
    MFR'S TEST
    RAINY SNOWY HEAVY OIL SAE 40

    FINE CLOUDY LIGHT OIL SAE 30


    WITNESS
    RAINY SNOWY HEAVY OIL SAE 40

    ENGINE SPECIFICATION GENERATOR SPECIFICATION


    MAKER : MAKER :

    MODEL & SERIAL No. : MODEL & SERIAL No. :

    RATED OUTPUT : RATED OUTPUT :


    kW rpm kVA kW
    CLY.No. X BORE X STROKE VOLTAGE : CURRENT :
    Cyl. X mm V A
    TOTAL DISPLACEMENT : FREQUENCY : POWER FACTOR :
    L Hz ø
    INJECTION TIMING : PHASE : POLES :
    BTDC
    HEAT DIRECT
    COOLING METHOD : RADIATOR RULE : MFG DATE :
    EXCHANGER COOLING
    IP23
    STARTING METHOD : RADIATOR SPECIFICATION
    ELECTRIC MODEL/PART NUMBER &
    GOV. TYPE MECHANICAL HYDRAULIC ELECTRIC SERIAL NO:
    STATUS
    TURBO MODEL :
    OK NOT OK
    INJ. PUMP MODEL OR PART No. :

    ENG, MFG. DATE GOVERNOR


    TRIMMER SETTING
    SETTING
    CON-ROD RANK DR Rated Speed: -
    GAIN
    I Low idle:
    D Rated Volt: 4-80

    APPROVED BY

    CHECKED BY

    TESTED BY
    ENGINE NUMBER
    V Confirmation at WITNESS TES

    PROTECTIVE DEVICE TEST @ Confirmation working by means of


    making contact
    ENGINE TRIP
    No ITEM SETTING WORKING INDICATION
    STOP SIGNAL
    1 EMERGENCY STOP Press Button CLOSE OPEN
    2 L/O LOW OIL PRESS BAR PRESSURE NORMAL 6 - 7 BAR 3,91 ALARM 1,5
    3 C/W HIGH TEMP CELCIUS NORMAL 69 -92 96 ALARM 101
    4 OVERSPEED RPM 1499 - 1501 1650 1750
    ENGINE NUMBER
    LOAD TEST STANDARD TEST
    START 10:00 10:05 10:15 10:25 10:35
    TIME
    FINISH 10:05 10:15 10:25 10:35 10:55 REMARKS
    Minutes 5 10 10 10 20
    LOAD % 0 25 50 75 100
    OUTPUT KW
    VOLTAGE V
    L1 A
    LOAD CURRENT L2 A
    L3 A
    GENERATOR

    POWER FACTOR
    FREQUENCY Hz
    o
    INLET C
    COOLING AIR TEMP o
    OUTLET C
    o
    AMBIENT TEMP C

    SPEED Rpm
    Flow Meter
    Consumption
    FLOW METER
    Liter/hours

    o
    COOLING WATER TEMP C
    LUBE OIL PRESS Bar
    ENGINE

    o
    INLET AIR TEMP C
    o
    EXHAUST GAS TEMP C
    o
    RADIATOR INLET C
    DC VOLTAGE ALTERNATOR VDC

    You might also like