501 SE Columbia Shores Boulevard, Suite 500

Vancouver, Washington 98661 USA

+1 360 859 1780 / smartrg.com

/ Gateway User Manual

Model:SR616ac

Release 1.1 April 2018

 Table of Contents
Welcome! 4 IP Filtering - Incoming 74
Purpose & Scope 4 MAC Filtering 75
Intended Audience 4 Parental Control 77
Getting Assistance 4 Time Restriction 77
Copyright and Trademarks 4 Url Filter 79
Disclaimer 4 Quality of Service 80
Quality of Service 80
Getting Familiar with your Gateway 5 QoS Queue 81
LED Status Indicators 5 QoS Classification 83
Connections 5 QoS Port Shaping 85
External Buttons 6 Routing 86
2.4GHz and 5GHz Buttons 6 Default Gateway 86
Reset Button 6 Static Route 87
Installing your Gateway 6 Policy Routing 88
Logging in to your Gateway's UI 7 RIP 89
Device Info 7 DNS 90
Summary 7 DNS Server 90
WAN 8 Dynamic DNS 92
Statistics 9 DNS Config 92
LAN 9 DSL 93
WAN Service 10 UPnP 96
xTM 11 DNS Proxy 97
xDSL 12 Interface Grouping 98
Route 16 IP Tunnel 99
ARP 17 IPv6inIPv4 100
DHCP 18 IPv4inIPv6 100
CPU & Memory 19 Certificate 101
Local 101
Advanced Setup 19 Trusted CA 104
Layer2 Interface 19 Power Management 105
ATM Interface 19 Multicast 105
PTM Interface 22 Managing group exception lists 107
ETH Interface 23
WAN Service 24 Wireless 108
Basic 108
PPP over Ethernet WAN Service 25
IP over Ethernet WAN Service 34 Security 110
Bridging 43 Open and Shared Authentication 112
VPN 46 802.1X Authentication 113
L2TP Client Configuration 46 WPA2 and Mixed WPA2/WPA Authentication 114
PPTP Client 49 WPA2-PSK and Mixed WPA2/WPA-PSK
Ethernet Config 53 Authentication 116
LAN 54 MAC Filter 117
IPv4 Autoconfig 58 Wireless Bridge 118
IPv6 Autoconfig 61 Advanced 119
Local VLAN Setting 63 Station Info 123
NAT 64 Wifi Insight 123
Virtual Servers 64 Site Survey 125
Port Triggering 67 Channel Statistics 126
DMZ Host 70 Metrics 126
ALG 71 Voice 128
Multi NAT 71 VoIP Status 128
Security 72 SIP Basic Setting 128
IP Filtering - Outgoing 72 SIP Advanced Setting 131

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 2
 Table of Contents
SIP Star Code Setting 136
SIP Extra Setting 136
SIP Debug Setting 138
SIP Black Filter 140
Diagnostics 141
Diagnostics 141
Ethernet OAM 142
Diagnostic Tools 145
Ping 145
Traceroute 147
Start / Stop DSL 148
Management 149
Settings 149
Backup 149
Update 150
Restore Default 151
System Log 151
Security Log 154
SNMP Agent 155
Management Server 156
TR-069 156
STUN Config 158
XMPP Connection 160
Internet Time 161
Access Control 162
Passwords 162
Access List 163
Services Control 164
User Profile 165
Logout Timer 165
Update Software 166
Reboot 167
Logout 168
Appendix: FCC Statements 169
FCC Interference Statement 169
FCC Radiation Exposure Statement 169
FCC - PART 68 169
Ringer Equivalency Number Statement 170
IC CS-03 statement 170
Canada Statement 170
5GHz 171
Revision History 172

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 3
Welcome!
Thank you for purchasing this SmartRG product.
SmartRG offers solutions that simplify the complex Internet ecosystem. Our solutions include hardware, software, applications,
enhanced network insights, and security delivered via a future-proof operating system. Based in the USA, SmartRG provides local,
proactive software development and customer support. We proudly offer the best, most innovative broadband gateways available.
Learn more at www.SmartRG.com.

Purpose & Scope

This Gateway User Manual provides SmartRG customers with installation, configuration and monitoring information for the
SR516acSR616ac gateway.

Intended Audience
The information in this document is intended for Network Architects, NOC Administrators, Field Service Technicians and other
networking professionals responsible for deploying and managing broadband access networks. Readers of this manual are assumed to
have a basic understanding of computer operating systems, networking concepts and telecommunications.

Getting Assistance
Frequently asked questions are provided at the bottom of the Subscribers page of the SmartRG Web site.

Subscribers: If you require further help with this product, please contact your service provider.
Service providers: if you require further help with this product, please open a support request.

Copyright and Trademarks

Copyright © 2017 by SmartRG, Inc. Published by SmartRG, Inc. All rights reserved.
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system,
translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
photocopying, manual, or otherwise, without the prior written permission of SmartRG, Inc.

Disclaimer
SmartRG does not assume any liability arising out of the application or use of any products, or software described herein. Neither
does it convey any license under its patent rights nor patent rights of others. SmartRG further reserves the right to make changes to
any products described herein without notice. This publication is subject to change without notice.
Any trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective
owners.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 4
Getting Familiar with your Gateway
This section contains a quick description of the gateway's lights, ports, and buttons to help you get familiar with the model.

LED Status Indicators

The indicator lights (LEDs) on the front of the SR616ac gateway
can help you understand the state of your gateway.

Legend: Green Green Blinking Red

LED Action Explanation
All LEDs except those Feature enabled &/or working correctly
listed below
Data being transferred

POWER Unit is booting up & preparing for use. When the unit is ready, the light changes to green.
Device powered on and ready for use

DSL DSL connected

INTERNET DSL sync acquired and gateway on line
Data being transferred
Internet authentication / connection has failed

Connections
The ports located on the back of the gateway and the buttons and ports located on the left side of the gateway, are described
below.

Feature Description
Rear panel
DSL This grey RJ11 port is used to connect your gateway to an Internet provider via a DSL service.
Phone 1 - 2 These grey RJ11 ports can be used to connect your gateway to an Internet provider via a telephone line.
LAN 1 - 4 The yellow RJ45 ports can be used to connect client devices such as computers and printers to your gateway.
WAN The blue RJ45 port is used to hard-wire your gateway to another network device.
For models with both WAN and DSL ports, when your Internet connection is via DSL, you can configure the WAN port to
function as an additional LAN port. For detailed instructions, see the Ethernet Mode section of this manual.
USB 1 Can transfer data, act as a printer interface, and handle a 3G accessory.
Power Use only the power supply included with your gateway. Intended for indoor use only.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 5
Feature Description
Left side
On/Off Power switch.
5GHz Enables or disables the 5GHZ wireless function.
2.4GHz Enables or disables the 5GHZ wireless function.

External Buttons
Smart RG gateways provide push-button controls on the exterior for critical features. These buttons provide a convenient way to
toggle the Wi-Fi radio on and off or reset the gateway. These controls are described below.

2.4GHz and 5GHz Buttons

These buttons are located on the left side of the gateway and control the Wi-Fi radio functions.
To turn a wireless radio on or off, press the related button for 3-5 seconds. For example, to turn the 2.4 GHz radio on or off, press
the 2.4GHz button for3-5 seconds.
To enable WPS, press the related button and hold it for 8-10 seconds.

Reset Button
The Reset button is a small hole in the back of the gateway with the actual button mounted beneath the surface. This style of push-
button prevents the gateway from being inadvertently reset during handling.
Warning: Do not press the Reset button unless you are sure that you want to clear the current settings.

Reboot your Gateway

Press the Reset button briefly with a paper clip or similar tool to reboot the device.
Perform FRESET
Press the Reset button for 10 seconds to factory reset your gateway.
Set your Gateway to CFE Mode
Press the Reset button for 15 seconds to put your gateway into CFE mode.

Installing your Gateway

1. Connect one end of the included phone cable to the DSL port on the gateway and connect the other end to the wall
jack.
2. Connect one end of an Ethernet cable to a LAN port of the gateway and connect the other end to your PC.
3. Plug the power adapter to the wall outlet and then connect the other end of it to the Power port of the gateway.
4. Turn on the unit by pressing the On/Off button on the left side of the gateway.

Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to complete before
you can begin using your Internet applications (browser, email, etc.).
If you are unable to connect to the Internet, confirm that all cable connections are in place and the router’s power is turned on.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 6
Logging in to your Gateway's UI
To configure the SmartRG gateway's settings, access the gateway's embedded UI.

1. Open a Web browser on your computer.

2. In the address field, enter http://192.168.1.1 (the default IP address of the DSL gateway). The authentication dialog
box appears.

3. Enter the user name and password. The default user name and password of the super user are admin and admin. The
username and password of the common user are user and user. It is recommended that you change these default
values after logging in to the DSL gateway for the first time.
4. Click OK. The Network Status page appears.
5. To view the log for this gateway, click View log at the bottom of the page. The log appears in a separate window.
6. To log into the GUI, click Manage gateway (advanced). The gateway interface appears, showing the Device Info
summary page.

Device Info
In this section, you can view data about your gateway and network, and configure DHCP, ARP, and WAN interfaces.

Summary
On this page, you can view device information such as the board ID, software and voice service version, and information about your
WAN connection such as the upstream rate and the LAN address.
When you log into the gateway GUI, the Device Info summary page appears.
You can also reach this page by clicking Device Info > Summary in the left menu.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 7
WAN
The WAN status screen provides a high level overview of the connection between your Internet Service Provider and your gateway
device. The WAN interface can physically be DSL or Ethernet and supports a number of Layer 2 and later configuration options
covered later in this document.
In the left navigation bar, click Device Info > WAN. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 8
The fields on this page are defined below.

Field Name Description

Interface The connection interface (Layer 2 interface) through which the gateway handles the traffic.
Description The service identifier such as pppoe_0_1_1.35.
Type The service type. Options are PPPoE, IPoE, and Bridge.
VlanMuxId The VLAN ID. Options are Disabled or 0 - 4094.
IPv6 The state of IPv6. Options are Enabled, Disabled, and N/A .
Igmp Pxy The state of the IGMP proxy. Options are Enabled, Disabled, and N/A .
Igmp Src Enbl The state of the IGMP source. Options are Enabled and Disabled.
MLD Pxy The state of the MLD proxy. Options are Enabled, Disabled, and N/A .
MLD Src Enable The state of the MLD source. Options are Enabled, Disabled, and N/A .
NAT The state of NAT. Options are Enabled and Disabled.
Firewall The state of the Firewall. Options are Enabled and Disabled.
Status The status of the WAN connection. Options are Disconnected, Unconfigured, Connecting, and Connected.
IPv4 Address The obtained IPv4 address.
IPv6 Address The obtained IPv6 address.

Statistics
In this section, you can view network interface information for LAN, WAN Service, xTM and DSL. Data is updated at 15-minute
intervals.

LAN
On this page, you can view the received and transmitted bytes, packets, errors and drops for each LAN interface configured on your
gateway. All local LAN Ethernet ports, Ethernet WAN ports and wireless interfaces are included.
In the left navigation bar, click Device Info > Statistics. The Statistics - LAN page appears.
To reset these counters, click Reset Statistics near the bottom of the page.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 9
The fields on this page are defined below.

Field Name Description

Interface Available LAN interfaces. Options are LAN1 - LAN4, ETHWAN, 5GHz Band, and 2.4 GHz Band.
Received & Transmitted columns
Bytes The total number of packets in bytes.
Pkts The total quantity of packets.
Errs The total quantity of error packets.
Drops The total quantity of dropped packets.

WAN Service
On this page, you can view the received and transmitted bytes, packets, errors and drops for each WAN interface for your gateway.
All WAN interfaces configured for your gateway are included.
In the left menu, click Device Info > Statistics > WAN Service. The Statistics - WAN page appears where you can view detailed
information about the status of your WAN.
To reset the counters, click Reset Statistics near the bottom of the page.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 10
The fields on this page are defined below.

Field Name Description

Interface Available WAN interfaces.
Description The service description. Options are pppoe, ipoe, and b, followed by the identifier for each service.
Received & Transmitted columns
Bytes The total number of packets in bytes.
Pkts The total quantity of packets.
Errs The total quantity of error packets.
Drops The total quantity of dropped packets.

xTM
On this page, you can view the ATM/PTM statistics for your gateway. All WAN interfaces configured for your gateway are included.
In the left navigation bar, click Device Info > Statistics > xTM. The Interface Statistics page appears.
To reset these counters, click Reset near the bottom of the page.

The fields on this page are defined below.

Field Name Description

Port Number Statistics for Port 1, or both ports if bonded.
In Octets Total quantity of received octets.
Out Octets Total quantity of transmitted octets.
In Packets Total quantity of received packets.
Out Packets Total quantity of transmitted packets.
In OAM Cells Total quantity of received OAM Cells.
Out OAM Cells Total quantity of transmitted OAM Cells.
In ASM Cells Total quantity of received ASM Cells.
Out ASM Cells Total quantity of transmitted ASM Cells.
In Packet Errors Total quantity of received packet errors.
In Cell Errors Total quantity of received cell errors.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 11
xDSL
On this page, you can view the DSL statistics for your gateway. All xDSL (VDSL or ADSL) interfaces configured for your gateway are
included. The terms and their explanations are derived from the relevant ITU­-T standards and referenced accordingly.

1. In the left navigation menu, click Device Info > Statistics > xDSL. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 12
 2. To run an xDSL (BER) test, follow the instructions in "Running xDSL (BER) tests".
3. To reset the counters, click Reset Statistics near the bottom of the page.

The fields on this page are defined below.

Field Name Description

Synchronized Time Time when the last synchronization was performed.
Number of Number of synchronizations performed.
Synchronizations
Mode xDSL mode that the modem has trained under, such as VDSL2+, G.DMT, etc.
Traffic Type Connection type. Options are ATM, PTM and ETH.
Status Status of the connection. Options are Up, Disabled, NoSignal , and Initializing.
Link Power State Current link power management state (e.g., L0, L2, L3).
Downstream and Upstream columns
Line Coding (Trellis) State of the Trellis Coded Modulation. Options are On and Off.
SNR Margin (0.1 db) Signal-to-noise ration (SNR) margin is the maximum increase (in dB) of the received noise power, such that
the modem can still meet all of the target BERs over all the frame bearers. [2]
Attenuation (0.1 db) Signal attenuation is defined as the difference in dB between the power received at the near-end and
that transmitted from the far-end. [2]
Output Power (0.1 dBm) Transmit power from the gateway to the DSL loop relative to one Milliwatt (dBm).
Attainable Rate (Kbps) Typical obtainable sync rate, i.e., the attainable net data rate that the receive PMS-TC and PMD
functions are designed to support under the following conditions:
l Single frame bearer and single latency operation.
l Signal-to-Noise Ratio Margin (SNRM) to be equal or above the SNR Target Margin.
l BER not to exceed the highest BER configured for one (or more) latency paths.
l Latency not to exceed the highest latency configured for one (or more) latency paths.
l Accounting for all coding gains available (e.g., trellis coding, RS FEC) with latency bound.
l Accounting for the loop characteristics at the instant of measurement. [2]
Rate (Kbps) Current net data rate of the xDSL link. Net data rate is defined as the sum of all frame bearer data rates
over all latency paths. [2]
Downstream and Upstream columns for DSL-specific fields only
B (# of bytes in Mux Data Nominal number of bytes from frame bearer #n per Mux Data Frame at Reference Point A in the current
Frame) latency path.
M (# of Mux Data Frames Number of Mux Data Frames per FEC Data Frame in the current latency path.
in FEC Data Frame
T (# of Mux Data Frames Ratio of the number of Mux Data Frames to the number of sync bytes in the current latency path.
over sync bytes)
R (# of redundancy Number of Reed Solomon redundancy bytes per codeword in the current latency path. This is also the
bytes in RS codeword) number of redundancy bytes per FEC Data Frame in the current latency path.
S (# of data symbols over Number of data symbols included within the RS code word.
which the RS code word
spans)

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 13
Field Name Description
L (# of bits in each data Number of bits included within each data symbol.
symbol)
D (interleaver depth) Interleaving depth in the current latency path.
I (interleaver block size Interleaving block size in the current latency path.
in bytes)
N (RS codeword size) The number of bits per codeword.
Delay (msec) PMS-TC delay in milliseconds of the current latency path (or the lowest latency path when running dual-
latency paths).
INP (DMT symbol) Input level for DMT-managed DSL environments.
OH Frames Number of xDSL OH Frames transmitted/received.
OH Frame Errors Number of xDSL OH Frames transmitted/received with errors.
(End of DSL-specific field group)
Super Frames The number of xDSL Super Frames transmitted/received.
Super Frame Errors The number of xDSL Super Frames transmitted/received with errors.
RS Words Number of Reed-Solomon-based Forward Error Correction (FEC) codewords transmitted/received.
RS Correctable Errors Number of Reed-Solomon-based FEC codewords received with errors that have been corrected.
RS Uncorrectable Errors Number of Reed-Solomon-based FEC codewords received with errors that were not correctable.
HEC Errors Count of ATM HEC errors detected. As per ITU-T G.992.1 and G.992.3, a1-byte HEC is generated for each
ATM cell header. Error detection is implemented as defined in ITU-T I.432.1 with the exception that any
HEC error shall be considered as a multiple bit error, and therefore, HEC Error Correction is not
performed. [1],[2]
OCD Errors Total number of Out-of-Cell Delineation errors. ATM Cell delineation is the process which allows
identification of the cell boundaries. The HEC field is used to achieve cell delineation. [4] An OCD Error is
counted when the cell delineation process transitions from the SYNC state to the HUNT state. [2]
LCD Errors Total number of Loss of Cell Delineation errors. An LCD Error is counted when at least one OCD error is
present in each of four consecutive overhead channel periods and SEF (Severely Errored Frame) defect is
present. [2]
Total Cells Total number of cells (OAM and Data cells) transmitted/received.
Data Cells Total number of data cells transmitted/received.
Bit Errors Total number of Idle Cell Bit Errors in the ATM Data Path. [3]
Total ES Total number of Errored Seconds. This parameter is a count of 1-second intervals with one or more CRC-8
anomalies. [4]
Total SES Total number of Severely Errored Seconds. An SES is declared if, during a 1-second interval, there are 18
or more CRC-8 anomalies in one or more of the received bearer channels, LOS (Loss of Signal) defects, SEF
(Severely Errored Frame) defects, or LPR (Loss of Power) defects. [4]
Total UAS Total number of Un-Aavailable Seconds.
This is a count of 1-second intervals for which the xDSL line is unavailable. The xDSL line becomes
unavailable at the onset of 10 contiguous SESs (included in the unavailable time).
Once unavailable, the xDSL line becomes available at the onset of 10 contiguous seconds with no SESs
(excluded from unavailable time). [4]

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 14
References
[1] ITU-T Recommendation G.992.1 (1999), Asymmetric digital subscriber line (ADSL) transceivers
[2] ITU-T Recommendation G.992.3 (2005), Asymmetric digital subscriber line transceivers 2 (ADSL2)
[3] ITU-T Recommendation G.997.1 (2006), Physical layer management for digital subscriber line (DSL) transceivers
[4] ITU-T Recommendation I.432.1 (1999), B-ISDN user-network interface – Physical layer specification: General characteristics

Running xDSL (BER) tests

1. Scroll to the bottom of the page and click xDSL BER Test. The ADSL BER Test dialog box appears.

2. In the Tested Time field, select the duration in seconds and click Start. Options range from 1 second to 360 seconds.
The default is 20 seconds.
The test transfers idle cells containing a known pattern and compares the received data with this known pattern.
Comparison errors are tabulated and displayed. To stop the test, click Stop.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 15
 3. When the test completes, a success dialog box appears.
Note: If the Error Ratio reaches e-5, you cannot access the Internet.

Route
On this page, you can view the LAN and WAN route table information configured in your gateway for both IPv4 and IPv6
implementation.
In the left navigation bar, click Device Info > Route. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 16
The fields on this page are defined below.

Field Name Description

Destination Destination IP addresses.
Gateway (For IPv4 only) Gateway IP address.
Subnet Mask (For IPv4 only) Subnet Mask.
Next Hop (For IPv6 only) Identifies the next server in the IPv6 path, if any.
Flag Status of the flags.
Metric Number of hops to reach the default gateway.
Service Service type.
Interface WAN/LAN interface.

ARP
On this page, you can view the MAC address and IP address information for the devices connected to the gateway.
In the left navigation bar, click Device Info > ARP. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 17
The fields on this page are defined below.

Field Name Description

IP address IP address of the host.
Flags Each entry in the ARP cache is marked with a status flag. Options are Complete, Permanent, and Published.
MAC Address MAC address of the host.
Device System level interface by which the host is connected. Options are: br(#), atm(#), eth(#), and ptm(#).

DHCP
On this page, you can view the host name, the IP address assigned by the DHCP server, the MAC address corresponding to the IP
address, and the DHCP lease time.

In the left navigation bar, select Device Info > DHCP. The following screen appears.

The fields on this page are defined below.

Field Name Description

Hostname Host name of each connected LAN device.
MAC Address MAC address for each connected LAN device.
IP Address IP address for each connected LAN device.
Connection Type Type of connection for each LAN devices, such as Ethernet.
IP Address Assignment Type of IP address assignment, such as DHCP.
Status Status of the connection. Options are Active and Inactive.
Expires In Time until the DHCP lease expires for each LAN device.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 18
CPU & Memory
On this page, you can view the CPU and memory data for the gateway.
In the left navigation bar, click Device Info > CPU & Memory. The following page appears, showing the current usage and history.
The information refreshes automatically.

Advanced Setup
In this section, you can configure network interfaces, UPnP, quality of service, and other features.

Layer2 Interface
In this section, you can configure the network interfaces for your gateway.

ATM Interface
On this page, you can configure Asynchronous Transfer Mode / Permanent Virtual Circuit (ATM/PVC) settings for your gateway. You
can customize latency options, link type, encapsulation mode and more.
Note: Devices (gateways) on both ends of the connection must support ATM / PVC.

1. In the left navigation bar, click Advanced Setup > Layer2 Interface > ATM Interface and then click Add. The following
page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 19
 2. Modify the settings as needed, using the information in the table below.
3. Click Apply/Save to commit your changes. The new interface appears on the DSL ATM Interface Configuration page.
4. To remove an interface, click the Remove checkbox next to it and then click the Remove button.

The fields on this page are defined below.

Field Name Description

VPI Enter a Virtual Path Identifier. A VPI is an 8-bit identifier that uniquely identifies a network path for ATM cell
packets to reach its destination. A unique VPI number is required for each ATM path. This setting works with
the VCI. Each individual DSL circuit must have a unique VPI/VCI combination. Options are 0-255. The default is
zero (0).
VCI Enter a Virtual Channel Identifier. A VCI is a 16-bit identifier for a unique channel. Options are 32-65535. The
default is 35.
Note: 1-31 are reserved for known protocols.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 20
Field Name Description
Select DSL Latency Select the level of DSL latency. Options are:
l Path0 (Fast): No error correction and can provide lower latency on error-free lines. This is the default.
l Path1 (Interleaved): Error checking that provides error-free data which increases latency.
Select DSL Link Select the linking protocol. Options are:
Type l EoA: Ethernet over ATM, used for PPPoE, IPoE, and Bridge. This is the default.
l PPPoA: Point-to-Point Protocol over ATM.
l IPoA: Internet Protocol over ATM.
Encapsulation Mode Select whether multiple protocols or only one protocol is carried per PVC (Permanent Virtual Circuit). Options
are:
l LLC/ENCAPSULATION: (Available for PPPoA only) Logical Link Control (LLC) encapsulation protocols
used with multiple PVCs
l LLC/SNAP-BRIDGING: (Available for EoA only) LLC used to carry multiple protocols in a single PVC.
l LLC/SNAP-ROUTING: (Available for IPoA only) LLC used to carry one protocol per PVC.
l VC/MUX: Virtual Circuit/Multiplexer creates a virtual connection used to carry one protocol per PVC.
Service Category Select the bit rate protocol. Options are:
l UBR without PCR: Unspecified Bit Rate with no Peak Cell Rate, flow control or time synchronization
between the traffic source and destination. Commonly used with applications that can tolerate data /
packet loss. This is the default.
l UBR with PCR: Same as above but with a Peak Cell Rate.
l CBR: Constant Bit Rate relies on timing synchronization to make the network traffic predictable. Used
commonly in Video and Audio traffic network applications.
l Non Realtime VBR: Non Realtime Variable Bit Rate used for connections that transport traffic at a
variable rate. This category requires a guaranteed bandwidth and latency. It does not rely on timing
synchronization between the destination and source.
l Realtime VBR: Realtime Variable Bit Rate. Same as the above option but relies on timing and
synchronization between the destination and source. This category is commonly used in networks with
compressed video traffic.
Select Scheduler Select the algorithm used to schedule queue behavior. VC scheduling is different than scheduling done for
for Queues of Equal default queues. Options are:
Precedence l Round Robin (weight=1): Packets are accessed in a round robin style. Classes can be assigned. Time
slices are assigned to each process in equal portions and in circular order, handling all processes
without priority (also known as cyclic executive). This is the default.
l Weighted Fair Queuing: Packets are assigned in a specific queue. This data packet scheduling
technique allows different scheduling priorities to be assigned to statistically multiplexed data flows.
Since each data flow has its own queue, an ill-behaved flow (that sent larger packets or more packets
per second than the others since it became active) will only affect itself and not other sessions.
Default Queue Enter the default weight of the specified queue. Options are 1-63. The default is 1.
Weight
Default Queue Enter the precedence of the specified group. The lower the value, the higher the priority. Options are 1-8.
Precedence The default is 8.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 21
PTM Interface
SmartRG gateway follow VDSL2 standards to support Packet Transfer Mode (PTM). An alternative to ATM mode, PTM transports
packets (IP, PPP, Ethernet, MPLS, and others) over DSL links. For more information, refer to the IEEE802.3ah standard for Ethernet in
the First Mile (EFM).
On this page, you can configure PTM WAN interfaces.

1. In the left navigation bar, click Advanced Setup > Layer2 Interface > PTM Interface, and then click Add. The
following page appears.

2. Modify the settings as desired, using the information in the table below.
3. Click Apply/Save to commit your changes. The new interface appears on the PTM Configuration page.
4. To remove an interface, click the Remove checkbox next to it and then click the Remove button.

Field Name Description

Select DSL Latency Select the level of DSL latency. Options are:
l Path0 (Fast): No error correction and can provide lower latency on error-free lines. This is
the default.
l Path1 (Interleaved): Error checking that provides error-free data which increases latency.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 22
Field Name Description
Select Scheduler for Queues Select the algorithm used to schedule queue behavior. VC scheduling is different than scheduling
of Equal Precedence done for default queues. Options are:
l Round Robin (weight=1): Packets are accessed in a round robin style and classes can be
assigned. Time slices are assigned to each process in equal portions and in circular order,
handling all processes without priority (also known as cyclic executive). This is the default.
l Weighted Fair Queuing: Packets are assigned in a specific queue. This data packet
scheduling technique allows different scheduling priorities to be assigned to statistically
multiplexed data flows. Since each data flow has its own queue, an ill-behaved flow (that
sent larger packets or more packets per second than the others since it became active) will
only affect itself and not other sessions.
Default Queue Weight Enter the default weight of the specified queue. Options are 1-63. The default is 1.
Default Queue Precedence Enter the precedence of the specified group. The lower the value, the higher the priority. Options
are 1-8. The default is 8.

ETH Interface
On this page, you can configure ETH WAN interfaces. One of the four LAN ports on your gateway can be re-purposed to become an
RJ45 WAN port when needed.
Notes:
l Only one Ethernet WAN interface is allowed. If a WAN port it is already configured, you must remove it before you can define
a new one. Click the Remove checkbox and then click the Remove button. The Add button appears when the existing port is
removed.
l If a WAN port is already configured and associated with a WAN service, you must remove the WAN service configuration before
you can remove the port on this page.

1. In the left navigation bar, click Advanced Setup > Layer2 Interface > ETH Interface. The following page appears.

2. To remove an entry, click the Remove checkbox next to the entry and then click the Remove button.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 23
 3. To add an entry, click Add. The following page appears.

4. Select the LAN port you want to use as a WAN port.

5. Click Apply/Save to commit your changes. The interface is added to the ETH WAN Interface Configuration page.

WAN Service
On this page, you can add, remove, or edit a WAN service. You must configure the related interface (ATM, ETH or PTM) first. You can
configure services for PPPoE, IPoE, and Bridging. A sample configuration scenario is provided for each variation.

1. In the left navigation, click Advanced Setup > WAN Service. The following page appears, showing any services
already configured.

2. To edit an interface:
a. Click the Edit button at the far right.
b. Modify the settings as needed and then click through to click Apply/Save.
3. To remove an interface, click the Remove checkbox next to it and then click the Remove button.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 24
 4. To add a service, click Add. The following page appears.

5. Configure the settings as desired, using the information in the topics listed below:
l "PPP over Ethernet WAN Service"
l "IP over Ethernet WAN Service"
l "Bridging"

PPP over Ethernet WAN Service

There are several parts to configuring a PPP over Ethernet (PPPoE) WAN service. You will progress through several pages to
complete the configuration.
Note: You can configure 7 services. If 7 services are configured, you must remove 1 of the services before configuring a new one.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 25
 1. In the left navigation bar, click Advanced Setup > WAN Service and then click Add. The following page appears.

2. Select the Layer 2 interface to use for the WAN service.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 26
 3. Click Next. The following page appears.

4. In the WAN Service Type field, accept the default of PPP over Ethernet (PPPoE).
5. (Optional) Modify the other fields, using the information in the following table.

Field Name Description

Enter Service Description (Optional) Enter a name to describe this configuration.
Enter 802.1P Priority Enter the priority for this service. Options are -1 and 0 - 7. The default is 0.
For tagged service, enter values in this field and the 802.1Q VLAN ID field.
For untagged service, accept the defaults of -1 (disabled) in this field and the 802.1Q
VLAN ID field.
Enter 802.1Q VLAN ID Enter the VLAN ID for this service. Options are 0 - 4094. The default is -1 (disabled).
For tagged service, enter values in this field and the 802.1P Priority field.
For untagged service, accept the defaults of-1 (disabled) in this field and the 802.1P
Priority field.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 27
 Field Name Description
Network Protocol Different scheduling priorities can be applied to statistically multiplexed data flows.
Selection Since each data flow has its own queue, an ill-behaved flow (which has sent larger
packets or more packets per second than the others) will only punish itself and not other
sessions. Options are IPv4 Only, IPv4&IPv6 (Dual Stack), and IPv6 Only.
Note: When you select IPV4&IPV6 or IPV6, the options presented on later pages change
accordingly.

6. Click Next. The following page appears where you will configure the PPP Username, Password and related
information.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 28
SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 29
 7. Modify the fields as needed, using the information in the table provided below.

Field Name Description

PPP Username and Password section
PPP Username Enter the username required for authentication to the PPP server.
Use base MAC address as Click this checkbox to use the base MAC address of the gateway as the PPP user name.
username
PPP Password Enter the password required for authentication to the PPP server.
PPPoE Service Name (Optional) Enter a description for this service.
Authentication Method Select a means for authentication. Options are:
l AUTO: Attempt to automatically detect the handshake protocol. This is the
default.
l PAP: Password Authentication Protocol (plaintext passwords).
l CHAP: Challenge Handshake Authentication Protocol. (MD5 hashing scheme on
passwords).
l MSCHAP: Microsoft Challenge Handshake Authentication Protocol. (Microsoft
encrypted password authentication protocol).
MTU [576-1492] Enter the MTU (Maximum Transmission Unit) size. Options are 576 - 1492 bytes. The
default is 1492 bytes.
Enable KeepAlive This option is enabled by default. Enter values in the following fields:
l LCP Echo Interval [1-60]: Enter the interval for sending echos in seconds. The
default is 30 seconds.
l LCP Echo Failure [1-100]: Enter the number of times that echos should be sent
before reporting echo failure. The default is 5 times.
To disable keepalive packets, clear the checkbox.
Enable NAT This option is enabled by default. To disable NAT (Network Address Translation), clear the
checkbox.
Enable Fullcone NAT Click to enable "one-to-one" NAT. All requests from the same internal IP address and port
are mapped to the same external IP address and port. In addition, any external host can
send a packet to the internal host by sending a packet to the mapped external address.
Warning: Enabling this option will disable network acceleration and some security
settings.
Enable Base MAC Click to allow the base MAC address to be ignored and another MAC address to be used.
Address Override

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 30
 Field Name Description
Enable MAC Clone Click to enable MAC cloning. Additional fields appear. Options are:
l To use a specific MAC address, enter the MAC address that you want to clone.
l To use the MAC address of the connected PC, click Clone this PC's MAC Address.
Enable Firewall This option is enabled by default. To disable the firewall, clear the checkbox.
Dial on Demand (with Click to enable dialing on-demand. The Inactivity Timeout (minutes) field appears. Enter
idle timeout timer) the number of minutes before a session is timed out. Options are 1 - 4320. The default is
zero (0).
When this option is enabled, connection automatically starts when there is outbound
traffic to the Internet. It automatically terminates if the connection is idle, based on the
value in the Idle Timeout setting.
PPP IP extension Click to forward all traffic to the specified DMZ IP.
Use Static IPv4 Address Click to use the IPv4 Address associated with this WAN service. The IPv4 Address field
appears. Enter the static IPv4 address for this WAN service.
Retry PPP password on This option is enabled by default. In the Max PPP authentication retries (1-65536) field,
authentication error enter the number of tries allowed. The default is 65536 (unlimited tries).
To prevent retrying the PPP password after authentication errors, clear the checkbox.
Enable IPv6 (Available only for IPv6 environments) Click to enable IP processing on a serial interface
Unnumbered Model without assigning it an explicit IP address. The IP address of another interface can
"borrow" the IP address of another interface already configured on the router, which
conserves network and address space.
Launch Dhcp6c for (Available only for IPv6 environments) Click to enable the gateway to receive the WAN IP
Address Assignment from the ISP.
(IANA)
Launch Dhcp6c for Prefix (Available only for IPv6 environments) This option is enabled by default and enables the
Delegation (IAPD) gateway to generate the WAN IP's prefix from the server's REST by MAC address. To disable
this options, clear the checkbox.
Enable PPP Debug Mode Click to have the system put more PPP connection information into the system log of the
device. This is for debugging errors and not for normal usage.
Bridge PPPoE Frames Select to enable PPPoE passthrough to relay PPPoE connections from behind the modem.
Between WAN and Local Also known as Half-Bridged mode.
Ports
IGMP Multicast section
Enable IGMP Multicast Click to enable Internet Group Membership Protocol (IGMP) multicast. Used by IPv4 hosts
Proxy to report multicast group memberships to any neighboring multicast routers.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 31
 Field Name Description
Enable IGMP Multicast Click to enable this service to act as an IGMP multicast source.
Source
MLD Multicast section
Enable MLD Multicast (Available only for IPv6 environments) Click to enable MLD multicast. Used by IPv4 hosts
Proxy to report multicast group memberships to any neighboring multicast routers.
Enable MLD Multicast (Available only for IPv6 environments) Click to enable this service to act as an MLD
Source multicast source.

8. Click Next. The following page appears where you will select the interface used as a default gateway used for the
PPP service being created.

9. Click the arrows to move your selections from left to right or from right to left.
10. (Optional) For IPv6 environments, in the Selected WAN Interface field, select the preferred WAN interface for the
default IPv6 gateway.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 32
 11. Click Next. The following page appears where you will select DNS Server settings.

12. Do one of the following to configure the DNS:

l Select the DNS server interface: Select interface entries and click the arrows to move the entries right or
left.
l Define a static DNS IP address: Click Use the following Static DNS IP address and enter the DNS server IP
addresses.
l Obtain IPv6 DNS info from a WAN interface: In the Obtain IPv6 DNS info from a WAN interface field, select
a WAN interface.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 33
 l Define a static IPv6 DNS IP address: Click Use the following Static IPv6 DNS address and enter the DNS
server IP addresses.
13. Click Next. The summary page appears indicating that your PPPoE WAN setup is complete.

14. Review the summary and either click Apply/Save to commit your changes or click Back to step through the pages in
reverse order to make any necessary alterations.

IP over Ethernet WAN Service

There are several parts to configuring an IP over Ethernet (IPoE) WAN service. You will progress through several pages to complete
the configuration.
Before you can configure a WAN service, make sure that the related Layer2 Interface has been configured.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 34
 1. In the left navigation bar, click Advanced Setup > WAN Service and then click Add. The following page appears.

2. Select an ATM interface to use for the WAN service and click Next. The following page appears.

3. Select IP over Ethernet.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 35
 4. Modify the other fields as needed, using the information in the following table.

Field Name Description

Enter Service (Optional) Enter a name to describe this configuration.
Description
Enter 802.1P Options are 0 - 7. The default is -1 (disabled).
Priority
For tagged service, enter values in this field and the 802.1Q VLAN ID field.
For untagged service, accept the defaults of -1 (disabled) in this field and the 802.1Q VLAN ID
field.
Enter 802.1Q VLAN Options are 0 - 4094. The default is -1 (disabled).
ID
For tagged service, enter values in this field and the 802.1P Priority field.

For untagged service, accept the defaults of -1 (disabled) in this field and the 802.1P Priority
field.
Network Protocol Different scheduling priorities can be applied to statistically multiplexed data flows. Since
Selection each data flow has its own queue, an ill-behaved flow (which has sent larger packets or more
packets per second than the others) will only punish itself and not other sessions. Options are
IPv4 Only, IPv4&IPv6 (Dual Stack), and IPv6 Only. The default is IPv4 Only.
Note: When you select IPV4&IPV6 or IPV6, the options presented on later pages change
accordingly.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 36
 5. Click Next. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 37
 6. Enter the relevant WAN IP Settings, using the information provided in the table below.

Field Name Description

Obtain an IP address This option is selected by default. DHCP is enabled in MER mode. Click to prevent
automatically the ISP automatically assigning the WAN IP to the gateway.
Option 50 Request IP Address Enter the IP address to be used when sending messages. If the specified address is
not available, the DHCP server assigns the next allowed IP address.
Option 51 Request Leased Time Enter the maximum lease time defined for the client. The default is 3600.
Option 54 Request Server Enter the IP address of the source server.
Address
Option 55 Request List Enter the DHCP parameters that you want the DHCP client to request. Enter them
in the order of preference, separated by commas. The minimum length is 1
character.
Option 60 Vendor ID (Optional) Enter the vendor ID to broadcast so the DHCP server can accept the
device.
Option 61 IAID (Optional) Enter the Interface Association Identifier (IAID). This is a unique
identifier for an IA, chosen by the client.
Option 61 DUID (Optional) Enter the DHCP Unique Identifier (DUID) is used by the client to get an IP
address from the DHCP server.
Option 77 User ID (Optional) Enter the user class ID that should be used to filter traffic.
Option 125 (Optional) Select whether local devices can automatically receive DHCP options
from the server. The default is Disable.
Use the following Static IP Click to manually declare the static IP information provided by your ISP. When you
address select this option, you must enter the WAN IP address, subnet mask and gateway IP
address.
WAN IP Address (Available only when Static IP address is selected) Enter the static WAN IPV4
address.
WAN Subnet Mask (Available only when Static IP address is selected) Enter the static subnet mask.
WAN gateway IP Address (Available only when Static IP address is selected) Enter the static gateway IP
address.
IPv6 settings section
The following fields appear when either IPv6 Only or IPv4&IPv6 (Dual Stack) is selected in the Network Protocol
Selection field on the WAN Service Configuration page.
Obtain an IPv6 address This option is set to enabled by default and allows the ISP to automatically assign
automatically the WAN IP address to the gateway. To disable the DHCPv6 Client on this WAN
interface, click the radio button.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 38
 Field Name Description
Dhcpv6 Address Assignment Select this option for the CPE to receive the WAN IP from the ISP.
(IANA)
Dhcpv6 Prefix Delegation (IAPD) This option is selected by default. The CPE generates the WAN IP's prefix from the
server's REST by MAC address. To disable this option, clear the checkbox.
Use the following Static IPv6 Select this option to enter the v6 Static IP information provided by your ISP.
address
WAN IPv6 Address/Prefix (Available only when Static IPv6 address is selected) If entering a static IP
Length address, enter the IP address / prefix length. If you do not specify a prefix length,
the default of /64 is used.
Prefix Delegation/Prefix Length (Available only when Static IPv6 address is selected) (Optional) Enter the prefix
delegation ID and prefix length for WAN.
WAN Next-Hop IPv6 address (Available only when Static IPv6 address is selected) Enter the IP address of the
next WAN in the group. This address can be either a local link or a global unicast
IPv6 address.

7. Click Next. The following page appears.

8. Modify the settings as needed for your environment.

Network Address Translation (NAT) allows you to share one Wide Area Network (WAN) IP address for multiple
computers on your Local Area Network (LAN). If you do not want to enable NAT (atypical) and wish the user of this

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 39
 gateway to access the Internet normally, you need to add a route on the uplink equipment. Failure to do so will cause
access to the Internet to fail.
The fields on this page are defined below.

FIELD NAME DESCRIPTION

Enable NAT This option is selected by default. Click to disable sharing the WAN interface across multiple
devices on the LAN. This setting also enables the functions in the NAT sub-menu and addition
PPPoE NAT features to select.
Enable Fullcone NAT Click to enable one-to-one NAT. All requests from the same internal IP address and port are
mapped to the same external IP address and port. In addition, any external host can send a
packet to the internal host by sending a packet to the mapped external address.

Warning: Enabling this option will disable network acceleration and some security settings.
Enable Firewall This option is selected by default. Click to disable functions in the Security sub-menu.
Enable IGMP Select to enable Internet Group Membership Protocol (IGMP) multicast. Used by IPv4 hosts to
Multicast Proxy report multicast group memberships to any neighboring multicast routers.
Enable IGMP Select to enable this service to act as an IGMP multicast source.
Multicast Source
Enable MLD (Available only for IPv6 environments) Click to enable multicast filtering. Used by IPv4 hosts
Multicast Proxy to report multicast group memberships to any neighboring multicast routers.
Enable MLD (Available only for IPv6 environments) Select to enable this service to act as a multicast
Multicast Source source.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 40
 9. Click Next. The following page appears.

10. Select a WAN interface to act as the system default gateway or accept the default interface.
11. (Optional) For IPv6 environments, in the Selected WAN Interface field, select the preferred WAN interface for the
default IPv6 gateway.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 41
 12. Click Next. The following page appears.

13. Modify the settings as needed.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 42
 14. Click Next. The following page appears.

15. Review the IPoE settings. You can modify the settings by clicking the Back button.
16. Click Apply/Save to save and apply the settings.

Bridging
Before you can configure a bridge WAN service, you must create the related Layer2 ATM interface.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 43
 1. In the left navigation bar, click Advanced Setup > WAN Service and then click Add. The following page appears.

2. Select the interface for the WAN service and then click Next. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 44
 3. Select Bridging. Multicast source fields appear.
4. Modify the other fields as needed, using the information in the following table.

Field Name Description

Allow as IGMP Multicast Select to enable this service to act as an IGMP multicast source.
Source
Allow as MLD Multicast Source Select to enable this service to act as an MLD multicast source.
Enter Service Description (Optional) Enter a different name to describe this configuration.
Enter 802.1P Priority Options are 0 - 7. The default is -1 (disabled).
For tagged service, enter values in this field and the 802.1Q VLAN ID field.

For untagged service, accept the default of -1 (disabled) in this field and in the
802.1Q VLAN ID field.
Enter 802.1Q VLAN ID Options are 0 - 4094. The default is -1 (disabled).
For tagged service, enter values in this field and the 802.1P Priority field.
For untagged service, accept the default of -1 (disabled) in this field and in the
802.1P Priority field.

5. Click Next. The summary page appears indicating that your Bridging WAN setup is complete.

6. Review the summary and either click Apply/Save to commit your changes or click Back to step through the pages in
reverse order to make any necessary alterations.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 45
VPN
In this section, you can configure tunneling protocols (L2TP or PPTP clients) for your network.

L2TP Client Configuration

On this page, you can configure the L2TP (Layer 2 Tunneling Protocol) client.

1. In the left navigation menu, click Advanced Setup > VPN and then click Add. The following page appears.

2. Fill in the fields, using the information in the table below.

Field Name Description

Description Enter a useful description of this configuration.
WAN Interface Select the WAN interface for this client.
L2TP Server IP/Domain Enter the IP address of the L2TP server.
L2TP Username Enter the user name for the server.
L2TP Password Enter the password for the server.
Authentication Select the authentication method. Options are NOAUTH, AUTO, PAP, CHAP, MS-CHAP_V1,
and MS-CHAP_V2. The default is AUTO.
Enable MPPE (Optional) Click to enable Microsoft Point-to-Point Encryption.
MTU (Optional) Enter the maximum number of transmission units allowed for this client. Options
are 576 - 1454. The default is 1454.
Enable NAT (Optional) Click to enable Network Address Translation features.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 46
 Field Name Description
Enable Firewall (SPI) (Optional) Click to enable the firewall.
Enable Click to enable this L2TP client configuration.

3. Click Next. The following page appears.

4. Select the default gateway by selecting interface entries and clicking the arrows to move the entries right or left.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 47
 5. Click Next. The following page appears.

6. Do one of the following to configure the DNS server:

l Select the DNS server interface: Select interface entries and clicking the arrows to move the entries right or
left.
l Define a static DNS IP address: Click Use the following Static DNS IP address and enter the DNS server IP
addresses.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 48
 7. Click Next. The summary page appears.

8. Click Apply / Save to implement your settings.

PPTP Client
On this page, you can configure the PPTP (Point-to-Point Tunneling Protocol) client.

1. In the left navigation menu, click Advanced Setup > VPN > PPTP Client and then click Add. The following page
appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 49
 2. Fill in the fields, using the information in the table below. The Description, WAN Interface, and PPTP Server
IP/Domain fields are required.

Field Name Description

Description Enter a useful description of this configuration.
WAN Interface Select the WAN interface for this client.
PPTP Server IP/Domain Enter the IP address of the PPTP server.
PPTP Username If not using the default of "admin", enter the user name for the server.
PPTP Password If not using the default of "admin", enter the password for the server.
Authentication Select the authentication method. Options are NOAUTH, AUTO, PAP, CHAP, MS-CHAP_V1,
and MS-CHAP_V2.
Enable MPPE (Optional) Select to enable Microsoft Point-to-Point Encryption.
MTU (Optional) Enter the maximum number of transmission units allowed for this client. Options
are 576-1454. The default is 1454.
Enable NAT (Optional) Select to enable Network Address Translation features.
Enable Firewall (SPI) (Optional) Select to enable the firewall.
Enable Click to enable this PPTP client configuration.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 50
 3. Click Next. The following page appears.

4. Select the default gateway by selecting interface entries and clicking the arrows to move the entries right or left.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 51
 5. Click Next. The following page appears.

6. Do one of the following to configure the DNS server:

l Select the DNS server interface: Select interface entries and clicking the arrows to move the entries right or
left.
l Define a static IP address: Click Use the following Static DNS IP address and enter the DNS server
IP addresses.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 52
 7. Click Next. The summary page appears.

8. Click Apply / Save to implement your settings.

Ethernet Config
On this page, you can configure the Ethernet speed for your gateway.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 53
 1. In the left navigation menu, click Advanced Setup > Ethernet Mode. The following page appears.

2. To set a specific speed, select it in the Configure field.

Options are Auto, 100 Full, 100 Half, 10 Full, and 10 Half. The default is Auto.
3. Click Apply/Save to apply your changes.

LAN
In this section, you can configure an IP address for the DSL gateway, enable IGMP snooping, enable or disable the DHCP server, edit
the DHCP options, configure the DHCP advanced setup, and set the binding between a MAC address and an IP address.
IGMP snooping enables the gateway to forward multicast traffic intelligently, instead of flooding all ports in the VLAN. With IGMP
snooping, the gateway listens to IGMP membership reports, queries and leave messages to identify the switch ports that are
members of multicast groups. Multicast traffic will only be forwarded to ports identified as members of the specific multicast group
or groups.
If you enable the DHCP server, the clients will automatically acquire the IP address from the DHCP server. If the DHCP server is
disabled, you need to manually set the start IP address, end IP address and the lease time for the clients in the LAN.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 54
 1. In the left navigation menu, click Advanced Setup > LAN. The following page appears.

2. (Optional) In the GroupName field, select the interface group for this configuration. If no groups are defined, the only
option is Default.
3. Modify the other fields using the information in the following table. The default configuration settings work for most
scenarios.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 55
 Field Description
IP Address / (Optional) Modify the IP address and subnet mask of the device. The default IP address is
Subnet Mask that of the gateway and the subnet mask is 255.255.255.0.
Enable IGMP Snooping This option is enabled by default. To disable this option, click the checkbox to clear it.
Options are Standard Mode and Blocking Mode. The default is Blocking Mode.
To disable this option, clear the check box.
Enable IGMP LAN to LAN This option is disabled by default. To enable this option, select Enable.
Multicast
Enable LAN side firewall Click to enable the LAN-side firewall.
Disable DHCP Server / This option is enabled by default. You can modify the address, server and leased time
Enable DHCP Server fields as needed.
To disable the DHCP server, click Disable DHCP Server. Then, if needed, enter different
server information for the LAN.
Edit DHCP Option 60 To modify the vendor class information, click Edit DHCP Option 60, modify the entries,
and click the appropriate action button. Then click Return.
Edit DHCP Option To add information about other DHCP options, click Edit DHCP Option, enter the
information for the desired options, and click the appropriate action button. Then click
Return.

4. To enable or disable DHCP for individual LAN interfaces:

a. Click DHCP Advanced setup. The DHCP Advance Setup page appears.

b. Click the State checkboxes as needed to manage DHCP for each LAN interface in the table, and then
click Advanced Setup > LAN > IPv4 Autoconfig in the left menu.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 56
 5. To add addresses to the Static IP Lease List:
a. Click Add Entries below the MAC Address table. The DHCP Static IP Lease page appears.

b. Enter the MAC address of the LAN host.

c. Enter the static IP address that is reserved for the host.
d. Click Apply/Save to apply the settings. You are returned to the LAN Setup page.
6. To remove entries from the Static IP Lease List, click the Remove check box next to the entry and then click
Remove Entries.
7. To add OUIs:
a. Click Add OUI below the OUI table. The DHCP OUI page appears.

b. Enter the OUI for the DHCP and click Apply/Save.

8. To remove entries from the OUI list, click the Remove check box next to the entry and then click Remove OUI.
9. To configure other DHCP options, in the Configure DHCP Options section, enter the required information for the
options (66, 150 and 43) that you want to configure. Instructions are displayed next to each field.
10. To define a second IP address and subnet mask for a LAN interface:
a. Click Configure the second IP Address and Subnet Mask for LAN interface. Additional fields appear.
b. Enter an IP address and a subnet mask for the LAN interface.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 57
 11. Click Apply/Save to apply your settings.

IPv4 Autoconfig
1. In the left navigation menu, click Advanced Setup > LAN. The following page appears. You can also reach this page by
clicking Advanced Setup > LAN > IPv4 Autoconfig in the left menu.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 58
 2. (Optional) In the GroupName field, select the interface group for this configuration. If there are no groupings
defined, the only option is Default.
3. Modify the other fields using the information in the following table. The default configuration settings work for most
scenarios.

Field Description
IP Address / (Optional) Modify the IP address and subnet mask of the device. The default IP address is
Subnet Mask that of the gateway and the subnet mask is 255.255.255.0.
Enable IGMP Snooping This option is enabled by default. Options are Standard Mode and Blocking Mode. The
default is Blocking Mode.
To disable this option, clear the check box.
Enable IGMP LAN to LAN This option is disabled by default. To enable this option, select Enable.
Multicast
Enable LAN side firewall Click to enable the LAN-side firewall.
Disable DHCP Server / This option is enabled by default. You can modify the address, server and leased time
Enable DHCP Server fields as needed.
To disable the DHCP server, click Disable DHCP Server. Then, if needed, enter different
server information for the LAN.
Edit DHCP Option 60 To modify the vendor class information, click Edit DHCP Option 60, modify the entries,
and click the appropriate action button. Then click Return.
Edit DHCP Option To add information about other DHCP options, click Edit DHCP Option, enter the
information for the desired options, and click the appropriate action button. Then click
Return.

4. To enable or disable DHCP for individual LAN interfaces:

a. Click DHCP Advanced setup. The DHCP Advance Setup page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 59
 b. Click the State checkboxes as needed to manage DHCP for each LAN interface in the table, and then
click Advanced Setup > LAN > IPv4 Autoconfig in the left menu.
5. To add addresses to the Static IP Lease List:
a. Click Add Entries below the MAC Address field. The DHCP Static IP Lease page appears.

b. Enter the MAC address of the LAN host.

c. Enter the static IP address that is reserved for the host.
d. Click Apply/Save to apply the settings. You are returned to the LAN Setup page.
6. To remove entries from the Static IP Lease List, click the Remove check box next to the entry and then click
Remove Entries.
7. To add OUIs:
a. Click Add OUI. The DHCP OUI page appears.

b. Enter the OUI for the DHCP and click Apply/Save.

8. To remove entries from the OUI list, click the Remove check box next to the entry and then click Remove OUI.
9. To define a second IP address and subnet mask for a LAN interface:
a. Click Configure the second IP Address and Subnet Mask for LAN interface. Additional fields appear.
b. Enter an IP address and a subnet mask for the LAN interface.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 60
 10. Click Apply/Save to apply your settings.

IPv6 Autoconfig
On this page, you can configure your gateway's IPv6 environment.

1. In the left navigation bar, click Advanced Setup > LAN > IPv6 Autoconfig. The following page appears.

2. To enable advertisement of the ULA prefix, click Enable ULA Prefix Advertisement. Additional fields appear.
3. Modify these and the other fields as needed, using the information in the table below.
4. Click Save/Apply to commit your changes.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 61
Field Name Description
Static LAN IPv6 Address Enter the interface address in IPv6 format (including the prefix length). This address must begin
Configuration with "fd". The prefix length must be "64". The address and prefix must reside on the same
network.
Enable ULA Prefix Check this option to enable unique local address (ULA) advertisement on the LAN. Options are
Advertisement Randomly Generate and Statically Configure. The default is Randomly Generate which enables
the gateway to generate a random IPv6 prefix.
If you select Statically Configure, additional fields become available. Modify these fields as
needed:
l Prefix: Enter the prefix, e.g., fd80::/64.
l Preferred Life Time: The default is -1 (no limit). The value in this field must be less than
or equal to the value in the Valid Life Time field.
l Valid Life Time: The value in this field must be greater than or equal to the value in the
Preferred Life Time field. The default is -1 (no limit).
IPv6 LAN Applications section
Enable DHCPv6 Server This option is selected by default. To disable the DHCP v6 feature on the LAN, click this checkbox
to clear it. Options are:
l Stateless: (Available only when Enable DHCPv6 Server is selected) This option is
selected by default. Click to stop inheriting IPV6 address assignments from the WAN IPV6
interface.
l Stateful: (Available only when Enable DHCPv6 Server is selected) Identifies the DHCPv6
server given by the LAN IPV6 network as configured with additional options.
Note: Zero compression is not supported. Make sure to enter zeros between the colons;
that is, do not use shorthand notation (enter "0:0:0:2", not ":::2").
Enter values in the following fields:
l Start interface ID: Enter the beginning IPv6 available addresses for DHCP to assign
to LAN devices.
l End interface ID: Enter the ending IPv6 available addresses for DHCP to assign to
LAN devices.
l Leased Time (hour): Enter the length of time before a new IPv6 lease is requested
by the LAN client.
Enable RADVD This option is enabled by default. It enables Router Advertisement Daemon (RADVD) service that
sends router advertisements to LAN clients. To disable RADVD, clear the check box .
Enable MLD Snooping This option is enabled by default. It enables Multicast Listener Discovery (MLD) snooping to
manage IPV6 multicast traffic. If you clear the check box to disable this feature, the MLD-related
fields are hidden. Options are:
l Standard Mode: Multicast traffic will flood to all bridge ports when no client subscribes to
a multicast group even if IGMP snooping is enabled.
l Blocking Mode: The multicast data traffic will be blocked and not flood to all bridge ports
when there are no client subscriptions to any multicast group. This is the default.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 62
Field Name Description
Enable MLD LAN to LAN (Optional) This option enables LAN-to-LAN Multicast until the first WAN service is connected.
Multicast Options are Disable and Enable. The default is Disable.
Enable Relay Click to enable the relay function. Additional fields appear. Do the following:

1. Enter the DHCPv6 Server IP Address.

2. Select a WAN interface. The default is Default.
3. Enter a Hop limit.The default is zero (0).

Local VLAN Setting

On this page, you can select a LAN port and enable VLAN mode on it.

1. In the left navigation menu, click Advanced Setup > LAN > Local VLAN Setting. The following page appears.

2. Select the LAN port on which you want to enable VLAN mode.
3. Click Enable VLAN Mode.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 63
 4. To add a VLAN:
a. Click Add. A table appears where you can enter the details.

b. Enter the VLAN ID. Options are 1 - 4094.

c. In the Pbits field, enter the type of bits being passed. Options are 1 - 7.
5. Click Apply/Save to apply your settings.
6. To remove a VLAN entry, click the Remove checkbox next to it and then click the Remove button.

NAT
In this section, you can configure the NAT (Network Address Translation) settings.

Virtual Servers
Firewall can prevent unexpected traffic on the Internet from your host on the LAN. The virtual server can create a channel that can
pass through the firewall. In that case, the host on the Internet can communicate with a host on your LAN within certain port range.
On this page, you can add or remove virtual server entries.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 64
 1. In the left navigation bar, click Advanced Setup > NAT. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 65
 2. To add a virtual server:
a. Click Add. The following page appears.

b. Modify the fields as needed, using the information in the table below.

Field Description
Use Interface Select the interface that you want to configure.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 66
 Field Description
Service Name Select or enter the service for which you want to forward IP packets. Options
are:
l Select a Service: Select from services defined for your network. The
port table at the bottom of the page is updated with the default port ID
defined for the service.
l Custom Service: Enter a new service name to establish a user service
type. You must enter the ports and select a protocol in the table at the
bottom of the page.
Server IP Address Enter the final octet of the IP address for this virtual server.
External Port Start When you select a service, the external port start and end numbers display
External Port End automatically. Modify them if necessary.
Protocol (Optional) Select the protocol for this service. Options are TCP/UDP, TCP, and
UDP. The default is TCP.
Internal Port Start When you select a service, the internal port start and end numbers display
Internal Port End automatically. Modify them if necessary.

3. Click Apply/Save to save the settings. The server or servers for the selected service appear on the NAT -- Virtual
Servers Setup page.
4. To remove an application from the list, click the checkbox in the Remove column and then click the Remove button.
The list is refreshed.

Port Triggering
Some applications need some ports to be opened in the firewall for the remote access. When an application initializes a TCP/UDP to
connect to a remote user, port triggering dynamically opens the open ports of the firewall.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 67
 1. In the left navigation bar, click Advanced Setup > NAT > Port Triggering. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 68
 2. To add a port trigger, click Add. The following page appears.

3. Modify the fields as needed, using the information in the following table.
4. To remove a trigger, click the Remove check box next to it and then click the Remove button. The list is refreshed.
5. Click Apply /Save to implement the settings.

Field Name Description

Use Interface Select the interface for which the port triggering rule will apply.
Application Name Select or enter the application that requires a port trigger. Options are:
l Select an Application: Select an available application. The Port and Protocol table is
populated with the related values.
l Custom Application: Enter a unique name for the application for which you are creating a
port trigger entry. You must enter the ports and select a protocol in the table at the bottom
of the page.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 69
Field Name Description
Trigger Port Start Enter the starting and ending numbers of the range of available outgoing trigger ports. Options are 1 -
Trigger Port End 65535.
Note: You can use a single port number, several port numbers separated by commas, port blocks consisting
of two port numbers separated by a dash, or any combination of these, for example 80, 90-140, 180.
Trigger Protocol Select the protocol required by the application that will be using the ports in the specified range. Options
are TCP, UDP, and TCP/UDP. The default is TCP.
Open Port Start Enter the starting and ending numbers of the range of available incoming ports. Options are 1 - 65535.
Open Port End
Open Protocol Select the protocol for the open port. Options are TCP, UDP, and TCP/UDP.

DMZ Host
DMZ allows all the ports of a PC on your LAN to be exposed to the Internet. On this page, you can set the IP address of a PC to be the
DMZ host, so that the DMZ host will not be blocked by your firewall.

1. In the left navigation bar, click Advanced Setup > NAT > DMZ Host. The following page appears.

2. Enter the DMZ Host IP Address.

3. (Optional) To enable on-demand link diagnostics, click Enable LAN Loopback.
4. Click Apply to commit the new or changed address.
5. To deactivate a DMZ host, delete the IP address from the DMZ Host IP Address field, and then click Apply.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 70
ALG
On this page, you can enable Session Initiation Protocol (SIP) for your NAT. SIP is a communications protocol for signaling and
controlling multimedia communication sessions.

1. In the left navigation bar, click Advanced Setup > NAT > ALG. The following page appears.

2. To disable SIP for your NAT, clear the SIP Enabled checkbox.
3. Click Save/Apply to commit the new or changed address.

Multi NAT
On this page, you can define rules for managing access to your NAT. You can create multiple rules and apply them to as many as
eight address ranges.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 71
 1. In the left navigation bar, click Advanced Setup > NAT > Multi NAT and then click Add. The following page appears.

2. Modify the fields as needed, using the information in the table below.

Field Description
Rule Type Select the type of rule. Options are One to One, One to Many, Many to One, and Many to
Many.
Use Interface Select the interface to which this rule will apply.
internalAddrStart Enter the starting address for the internal server.
internalAddrEnd Enter the ending address for the internal server.
externalAddrStart Enter the starting address for the external server.
externalAddrEnd Enter the ending address for the external server.

3. Click Apply/Save to save and apply the settings. The server or servers for the selected service appear on the
MultiNat table page.

Security
In this section, you can configure the incoming and outgoing IP filtering and MAC filtering.

IP Filtering - Outgoing
On this page, you can add an outgoing filter and prevent certain data being transferred from the LAN to the WAN.
You can define up to 32 outgoing IP filters.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 72
 1. In the left navigation bar, click Advanced Setup > Security and then click Add. The following page appears. You can
also reach the Outgoing IP Filtering Setup page by clicking Advanced Setup > Security > IP Filtering > Outgoing.

2. Fill in the fields, using the information in the table below.

3. Click Apply/Save to commit the completed entry.

The fields on this page are defined below.

Field Name Description

Filter Name Enter a descriptive name for this filter. No special characters or spaces are allowed.
IP Version For the filter to be configured and effective for IPV6, the gateway must be installed on a network that is either
a pure IPV6 network (with that protocol enabled) or is both IPV4 and IPV6 dual protocol enabled/configured.
Options are IPv4 and IPv6. The default is IPv4.
If you select IPV6, Source IP address and Destination IP address must be specified in IPV6 format, i.e., an IPV6-
compliant, hexadecimal address such as: 2001:0DB8:AC10:FE01:0000:0000:0000:0001.
Protocol Select the protocol profile for the filter you are defining. TCP/UDP is most commonly used. Options are
TCP/UDP, TCP, UDP, and ICMP.
Source IP address Enter the source IP address of a LAN side host for which you wish to block outgoing traffic using the specified
[/prefix length] protocol(s).
Note: The address specified here can be a particular address or a block of IP addresses on a given network
subnet. This is done by appending the associated routing "prefix" length decimal value (preceded with the
slash) to the addresses.
Source Port (port Set the source host port (or range of ports) for the above host (or range of hosts) to define the ports profile for
or port:port) which egress traffic will be blocked from reaching the specified destination(s).

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 73
Field Name Description
Destination IP Enter the destination IP address of a LAN side host for which you wish to filter (block) outgoing traffic using the
address [/prefix specified protocol(s).
length]
Note: The address specified here can be a particular address or a block of IP address on a given network
subnet. This is done through appending the address with the associated routing "/prefix" length decimal value
(preceded with the slash).
Destination Port Set the destination host port (or range of ports) for the above host (or range of hosts) to define the destination
(port or port:port) port profile for which egress traffic will be blocked, e.g., for a computer external to the local network.

IP Filtering - Incoming
On this page, you can add an incoming filter and prevent certain data being transferred from the WAN to the LAN.

1. In the left navigation bar, click Advanced Setup > Security > IP Filtering > Incoming and then click Add. The following
page appears.

2. Fill in the fields, using the information in the table below. The Filter Name and Protocol fields are required.
3. Click Apply/Save to commit your changes.

The fields on this page are defined below.

Field Name Description

Filter Name Enter a descriptive name for this filter. No special characters or spaces are allowed.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 74
Field Name Description
IP Version For the filter to be configured and effective for IPV6, the gateway must be installed on a network that is
either a pure IPV6 network (with that protocol enabled) or is both IPV4 and IPV6 dual protocol
enabled/configured. Options are IPv4 and IPv6. The default is IPv4.
If you select IPV6, Source IP address and Destination IP address must be specified in IPV6 format, i.e.,
an IPV6-compliant, hexadecimal address such as: 2001:0DB8:AC10:FE01:0000:0000:0000:0001.
Protocol Select the protocol to be associated with this incoming filter. Options are TCP/UDP, TCP, UDP, or ICMP.
Source IP address Enter the source IP address for this filter. For IPv6, enter the prefix as well.
[/prefix length]
Source Port (port or Enter a source port number or range (xxxxx:yyyyy).
port:port)
Destination IP address Enter the destination IP address for this filter. For IPv6, enter the prefix as well.
[/prefix length]
Destination Port (port or Enter destination port number or range (xxxxx:yyyyy).
port:port)
DROP Click to create a filter that will drop packets that meet the conditions of this filter.
WAN Interfaces Click to apply this rule to all WAN interfaces or only certain types. Options are Select All or select any of
the types defined for your network. The default is Select All .

MAC Filtering
On this page, you can manage MAC filtering for your gateway.

Your gateway can block or forward packets based on the originating device. This MAC filtering feature is available only in Bridge
mode. For other modes, similar functionality is available via IP Filtering.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 75
 1. In the left navigation bar, click Advanced Setup > Security > MAC Filtering. The following page appears.

2. To modify settings for an existing policy, click the Change checkbox next to it, and then click Change Policy. Options
are BLOCKED and FORWARD. The page refreshes, showing that the action has changed. The Change Policy button
acts like a toggle switch, clicking it switches the policy from BLOCKED to FORWARD and back again.
3. To add a MAC filtering rule, click Add and follow the instructions in Adding a MAC Filter.
4. To remove a rule, click the Remove checkbox next to the rule and click the Remove button.
5. When your changes are completed, click Apply/Save to commit your changes.

Adding a MAC Filter

You cannot edit rules but you can add new ones and then remove the obsolete ones.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 76
 1. On the MAC Filtering Setup page, click Add. The following page appears.

2. Fill in the fields, using the information provided in the following table. The Protocol Type field is required.
3. Click Apply/Save to commit your changes.

Field Name Description

Protocol Type Select the protocol associated with the device at the destination MAC address. Options are PPPoE, IPv4,
IPv6, AppleTalk , IPX, NetBEUI, and IGMP.
Destination MAC Enter the MAC address of the device that you want to associate with this filter.
Address
Source MAC Address Enter the MAC address of the device that originates the requests intended for the device associated with
the Destination MAC Address.
Frame Direction Select the incoming/outgoing packet interface. Options are LAN<=>WAN, WAN=>LAN, and LAN=>WAN.
The default is LAN<=>WAN (both directions).
WAN Interfaces Select the WAN interface(s) for which the filter should apply. Only interfaces configured for Bridge mode
are available.

Parental Control
In this section, you can manage time restrictions and block or allow specific URLs.

Time Restriction
On this page, you can control time restriction settings for a LAN device that connects to the gateway.
Note: Before you can create a time restriction rule, the gateway's time must be set. You can do this on the Management > Internet
Time page.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 77
 1. In the left navigation menu, click Advanced Setup > Parental Control and then click Add. The following page
appears.

2. Enter the user name for which this rule applies.

3. (Optional) Enter an additional MAC address by clicking Other MAC Address and entering the address in the adjacent
field.
4. Select the days of the week when this rule should apply.
5. Enter the starting and ending times for the periods that you want blocked. Use 24-hour format.
6. Click Apply/Save to implement the settings. You are returned to the Parental Control > Access Time Restriction page.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 78
Url Filter
On this page, you can prevent the LAN users from accessing some Web sites.

1. Click Advanced Setup > Parental Control > Url Filter. The following page appears.

2. Select whether to exclude or include the URLs in the list you are going to create. If you select Exclude, users cannot
access the URLs in the list. If you select Include, users can access the URLs in the list.
3. To create the list of URLs, click Add. The following page appears.

4. Enter the URL address and its corresponding port number. For example, enter http://www.google.com as the URL
address and 80 as the port number. If you leave the Port Number field blank, the default port number of 80 is used.
5. Select the days of the week when this rule will apply.
6. Enter the starting and ending time periods when this rule should be active. Use 24-hour format.
7. Click Apply/Save to save your changes. You are returned to the Parental Control > URL Filter page.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 79
Quality of Service
Quality of Service (QoS) enables prioritization of Internet content to help ensure the best possible performance. This is particularly
useful for streaming video and audio content with minimized potential for drop-outs. QoS becomes significant when the sum of all
traffic (audio, video, data) exceeds the capacity of the line.
In this section, you can disable/enable QoS and configure queues and classification rules.

Quality of Service
On this page, you can enable or disable QoS and set the DSCP Mark classification.
The maximum number of queues that can be configured vary by mode, as shown below.

Mode Maximum # of queues

ATM 16
Ethernet & Ethernet WAN 8 per interface
PTM 8

Note: Queues for wireless connections (e.g., WMM Voice Priority) are shown only when wireless is enabled. If the WMM Advertise
option on the Wireless > Basic Setup page is disabled, assigning classifications to wireless traffic has no effect.

1. In the left navigation bar, click Advanced Setup > Quality Of Service. The following page appears. The Quality of
Service feature is enabled by default.

2. To disable QoS for ALL interfaces, click the Enable QoS check box to clear it.
3. (Optional) Select the default DSCP Mark (Differentiated Services Code Point) classification value to be used. The
default is No Change(-1).
4. Click Apply/Save to save your settings.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 80
QoS Queue
On this page, you can configure a queue and add it to a selected Layer2 interface. You can also edit and delete queues. A number of
standard queues are already defined. You may have to remove queues that you don't need in order to create the desired queues.

1. In the left navigation bar, click Advanced Setup > Quality Of Service > QoS Queue. The following page appears.

2. To add a queue:
a. Click Add at the bottom of the table. The following page appears.

b. Fill in the fields, using the information in the following table. The visible fields vary by interface and

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 81
 queue precedence selections. In most cases, you can use the default values.
c. Click Apply/Save. You are returned to the Qos Queue Setup page.
3. To remove a queue, click the Remove checkbox to the right of the entry and then click the Remove button at the
bottom of the page.
4. Click Apply/Save to save your settings.

The applicable fields are explained below.

Field Name Description

Name Enter a descriptive name for this configuration.
Enable Select to enable or disable this QoS queue for the interface that you select. Options are Enable and Disable.
The default is Enable.
Interface Select the Layer 2 interface to be associated with the defined QoS queue, e.g., eth0 or ptm01.
Queue Precedence (Appears when atm, eth or ptm interfaces are selected in the Interface field) Select the priority value to
be associated with the defined QoS queue. Options vary by interface and can include 1(SP), 1(WRR|WFQ), 2
(SP), 3(WRR), 4(SP|WRR|WFQ), and so on.
Note: The lower the precedence value, the higher priority the queue is given. Traffic is given priority based
on the combined values from this field and Queue Weight field.
The following fields become visible based on your selections in the Interface and Queue Precedence fields. Which fields appear
vary by your selections. The fields are listed below in alphabetical order.
DSL Latency This option is set to Path0 by default and cannot be changed. No error correction is performed. This can
reduce latency on error-free lines.
Minimum Rate Enter the minimum shaping rate defined for packets in QoS queues. Options are 1 - 100000 Kbps. The default
is -1 (no minimum shaping rate).
PTM Priority Select the priority for this queue. Options are Low and High. The default is Low.
Queue Weight Enter the weighting value to associate with this queue. Options are 1 - 63. The default is 1.
Note: The higher the weighting value, the more frames that are sent proportionately given the WRR
algorithm employed. Traffic is given priority based on the combined values from this field and the Queue
Precedence field.
Scheduler Algorithm Select an algorithm for data priority in queues. Options are:
l Weighted Round Robin: Applies a fair round robin scheme weighting that is effective for networks
with fixed packet sizes, e.g., ATM networks.
l Weighted Fair Queuing: Applies a fair queuing weighting scheme via allowing different sessions to
have different service shares for improved data packets flow in networks with variable packet size,
e.g., PTM/IP networks.
Shaping Burst Size Enter the shaping burst size to be applied to packets in the defined queue. Options are 1600 bytes or
greater.
Shaping Rate Enter the shaping rate for packets in QoS queues. Options are 1 - 100000 Kbps. The default is -1 (no minimum
shaping).

WLAN Queue
On this page, you can view the WLAN queues defined for your network.
Note: Make sure that wireless connection is active by going to Wireless and clicking Apply/Save.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 82
In the left navigation bar, click Advanced Setup > Quality Of Service > QoS Queue > Wlan Queue. The following page appears.

QoS Classification
On this page, you can create classifications (traffic class rules) for assigning ingress traffic to a priority queue.

1. In the left navigation bar, click Advanced Setup > Quality Of Service > QoS Classification and then click Add. The
following page appears. A maximum of 32 entries can be configured.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 83
 2. Fill in the fields, using the information in the table below.
3. Click Apply/Save to commit your changes.

The fields on this page are defined below.

Field Name Description

Add Network Traffic Class Rule section
Traffic Class Name Enter a descriptive name for this rule.
Rule Order This option is set to Last and cannot be changed. Every rule is set as the very last classification rule
to be processed.
Rule Status Select whether this rule is active or inactive. Options are Enable and Disable. The default is Enable.
Specify Classification Criteria section
All fields in this section are optional. A blank field identifies a criterion that is not used.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 84
Field Name Description
Ingress Interface Select an interface for incoming traffic. Options are LAN, WAN, Local , 2.4GHz, 5GHz, and any
interface defined for your network. The default is LAN.
Ether Type Select the Ethernet interface type for this classification. Options include IP, ARP, IPV6, PPPoE, and
any other Ethernet interface defined for your network.
Source MAC Address / Mask (Available for LAN, ATM, ETH, PPP-Routed and wireless interfaces only) Enter the source MAC
address and source MAC mask for this classification.
Destination MAC Address / (Available for LAN, ETH and wireless interfaces only) Enter the destination MAC address and
Mask destination MAC mask for this classification.
Source IP Address [/ Mask] or (Available for WAN, ATM and PPP-Routed interfaces only) Select the source for this classification.
Vendor Class ID or User Class Options are:
ID l Source IP Address[/Mask]: Enter the source IP address and source IP mask.
l Vendor Class ID (DHCP Option 60): Enter the vendor class ID.
l User Class ID (DHCP Option 77): Enter the user class ID.
Destination IP Address (Available for WAN and ATM interfaces only) Enter the destination IP address and source IP mask for
[/ Mask] this classification.
IP Length Check (Min/Max) (Available for Local, ATM interfaces only) Enter the minimum and maximum number of digits
required for IP addresses.
Protocol (Available for WAN, Local, and ATM interfaces only)Select the protocol specified for this
classification. Options are TCP, UDP, ICMP, and IGMP.
UDP/TCP Source Port (Appears when TCP or UDP is selected in the Protocol field) Enter the source port to be used for
this classification. You can enter a range (port:port) or a single port.
UDP/TCP Destination Port (Appears when TCP or UDP is selected in the Protocol field) Enter the destination port to be used
for this classification. You can enter a range (port:port) or a single port.
Specify Classification Results section
Specify Egress Interface Select an interface for outgoing traffic. Options include any interface defined for your network.
Specify Egress Queue Select from the available queues.
Note: Make sure to select a queue that is defined for the interface that you selected. If you select a
queue that is not defined for the selected interface, any packets classified into that queue are
processed by the default queue for the interface.
Mark Applied Differentiated Select the desired DSCP code.
Service Code Point
Mark 802.1p priority (Available for LAN, bridged and wireless interfaces only) This value is inserted into the Ethernet
frame and used to differentiate traffic. Lower values assign higher priorities. Options are 0 - 7.
Set Rate Limit (Kbps) Enter the data traffic rate limit for this classification in kilobits per second.

QoS Port Shaping

On this page, you can configure a fixed rate (Kbps) for each of the Ethernet ports.

1. In the left navigation bar, click Advanced Setup > Quality Of Service > QoS Port Shaping. The following page
appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 85
 2. (Optional) For each interface in the table, enter a Shaping Rate (in Kbps) and a Burst Size (in bytes). The default
settings work for most scenarios.
3. Click Apply/Save to commit your changes.

Routing
In this section, you can configure default gateway, static routing, policy routing and RIP settings.

Default Gateway
On this page, you can select the WAN interface for the default gateway.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 86
 1. In the left navigation bar, click Advanced Setup > Routing. The following page appears.

2. (Optional) Select entries in the lists and click the arrows to move your selections from left to right or right to left.
3. (Optional) In the Selected WAN Interface field, select the appropriate interface.
4. Click Apply/Save to implement the settings.

Static Route
On this page, you can configure static routes for your network. Static route is a form of manually configured, fixed route for IP data.
You can enter a maximum of 32 entries.

1. In the left navigation bar, click Advanced Setup > Routing > Static Route and then click Add. The following page
appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 87
 2. Fill in the fields, using the information in the table below.
3. Click Apply/Save to commit your changes.

Field Name Description

IP Version Select the IP version associated with the static route you wish to create. Options are IPv4 and IPv6. The
default is IPv4.
Destination IP address/ Enter the destination network address / subnet mask for this route.
prefix length
Interface Select the WAN Interface for this route. This list is filtered by the selected IP version.
Gateway IP Address Enter the next-hop IP address. If needed, include the /prefix length.
Metric (Optional) Enter a number that is zero or higher.

Policy Routing
Policy routing makes somewhat automated routing choices based on policies defined by a network administrator. For example, a
network administrator might want to deviate from standard routing based on destination markers in the packet and, instead,
forward a packet based on the source address. Use this feature to establish similar policies.

1. In the left navigation bar, click Advanced Setup > Routing > Policy Routing and then click Add. The following page
appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 88
 2. Fill in the fields, using the information in the table below.
3. Click Apply/Save to commit your changes. You are returned to the Policy Routing Setting page.
4. To remove a route, click the Remove check box next to it and then click the Remove button. The list is refreshed.

Field Name Description

Policy Name Enter a descriptive name for this entry to the policy routing table. The maximum is 8 characters. Special
characters are not allowed.
Physical LAN Port Select a physical LAN interface for the policy route. Options include Ethernet (LAN) ports 1-4 and both
wireless bands.
Source IP Enter the IP address for the source of the policy route.
Use Interface Select the WAN Interface for this policy route.
Default Gateway IP Enter the IP address for the default gateway associated with the selected interface. If you select an IPoE
interface, the IP address is required.

RIP
RIP (Routing Information Protocol) is a type of distance-vector routing protocol, which leverages hop count as a metric for routing. RIP
puts a limit on the number of hops (maximum of 15) allowed in order to prevent routing loops. This can sometimes limit the size of
networks where RIP can be successfully employed.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 89
 1. In the left navigation bar, click Advanced Setup > Routing > RIP. The following page appears.

2. For the interface that you want to modify, select values using the information in the table below.
3. To enable a configuration, click the Enabled checkbox next to the interface.
4. Click Apply/Save to commit your changes.

Field Name Description

Interface Displays a list of available WAN interfaces.
Version Select the applicable version of the Routing Interface Protocol. For detailed information about versions, refer to
RFC 1058 and RFC 1453. Options are 1, 2, and Both. The default is 2.
Operation This option is set to Passive and cannot be changed. This mode listens only. It does not advertise routes.

DNS
In this section, you can configure a DNS server, dynamic DNS and static DNS.

DNS Server
On this page, you can select a DNS server interface from the available interfaces, manually enter the DNS server addresses, or
obtain the DNS address from a WAN interface.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 90
 1. In the left navigation bar, click Advanced Setup > DNS. The following page appears.

2. Do one of the following to configure the DNS server:

l Select the DNS server interface from available WAN interfaces: Select interface entries in the lists and
click the arrows to move the entries right or left.
l Define a static DNS IP address: Click Use the following Static DNS IP address and enter the DNS server IP
addresses.
l Obtain IPv6 DNS information from a WAN interface: Select the interface in the WAN Interface Selected
field. If no WAN interface is configured for your gateway, this field is disabled.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 91
 l Define a static IPv6 DNS IP address: Click Use the following Static IPv6 DNS address and enter the DNS
server IP addresses.
3. Click Apply/Save to apply your settings.

Dynamic DNS
Dynamic DNS (DDNS) automatically updates a name server in the DNS with the active DNS configuration of its configured hostnames,
addresses or other data. Often this update occurs in real time. You can configure the settings for this feature on this page.

1. In the left navigation bar, click Advanced Setup > DNS > Dynamic DNS and then click Add. The following page
appears.

2. Modify the fields as needed, using the information in the table below.
3. Click Apply/Save to commit your changes.

Field Name Description

D-DNS provider Select a dynamic Domain Name Server provider. Options are DynDNS.org, TZO or no-ip.com. The default is
DynDNS.org.
Hostname Enter the host name of the dynamic DNS server.
Interface Select the WAN interface whose traffic will be pointed at the specified Dynamic DNS provider.
DynDNS Settings section
Username Enter the username for accessing the dynamic DNS server.
Password Enter the password for accessing the dynamic DNS server.

DNS Config
On this page, you can configure static host names for your DNS domains.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 92
 1. In the left navigation bar, click Advanced Setup > DNS > DNS Config. The following page appears.

2. To add a DNS domain, click Add. The following page appears.

3. Enter a domain name and IP address for the domain. Only letters, numbers, dashes, and periods are allowed.
4. Click Apply/Save to apply your settings.

DSL
On this page, you can set the DSL settings. The modem negotiates the modulation mode with the DSLAM; you usually do not need to
modify the factory default settings.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 93
 1. In the left navigation menu, select Advanced Setup > DSL. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 94
SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 95
 2. Modify the settings as needed.
3. (Optional) To modify additional parameters, click Advanced Settings. The following page appears.

4. Select the test mode that you want to run.

5. To view the tone selection table, click Tone Selection. Changing these settings arbitrarily is not recommended.
Close the window to return to the DSL Advanced Settings page.
6. Click Apply and then click DSL in the left menu to return to the DSL page.
7. Click Apply/Save to save your changes.

UPnP
On this page, you can enable or disable the UPnP function.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 96
 1. In the left navigation menu, click Advanced Setup > UPnP. The following page appears.

2. To disable UPnP, click the Enable UPnP check box to clear it.
3. Click Apply/Save to save and apply the settings.

DNS Proxy
On this page, you can enable or disable the DNS proxy function. This function is enabled by default.

1. In the left navigation menu, click Advanced Setup > DNS Proxy. The following page appears.

2. To disable the DNS Proxy, click the Enable DNS Proxy checkbox to clear it.
3. To modify the host and domain, enter the host name of the new broadband gateway and the domain name of the LAN
network.
4. Click Apply/Save to implement the settings.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 97
Interface Grouping
On this page, you can configure interface groupings. Interface grouping supports multiple ports to PVC and bridging groups. Each
group performs as an independent network. Only the default group has an IP interface. To support this feature, you must create
mapping groups with the appropriate LAN and WAN interfaces.

1. In the left navigation menu, click Advanced Setup > Interface Grouping. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 98
 2. To add a new grouping, click Add. The following page appears.

3. Follow the on-screen instructions and then click Apply/Save.

4. To remove a grouping from the list, click the Remove checkbox next to the group name and then click the Remove
button. You can only remove groupings that you create.

IP Tunnel
IP Tunneling is typically used as a means to establish a path between two independent networks.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 99
In this section, you can configure connections of IPv6 networks across the IPv4 internet or IPv4 in IPv6.

IPv6inIPv4
On this page, you can configure a tunnel for IPv6inIPv4.

1. In the left navigation bar, click Advanced Setup > IP Tunnel and then click Add. The following page appears.

2. Enter a Tunnel Name. In the Mechanism field, the only option is 6RD.
3. Select the WAN and LAN interfaces associated with the tunnel you wish to establish.
4. Do one of the following:
l To configure the LAN interface settings manually, enter values in the fields located below the Manual button:
l IPv4 Mask Length: Options are 0 - 32.
l 6rd Prefix with Prefix Length: Prefix/length, such as: 2002::/64.
l Border Relay IPv4 Address: IP address for the IPv4 relay server.
l To configure these settings automatically, click Automatic.
5. Click Apply/Save to commit your changes.

IPv4inIPv6
On this page, you can configure a tunnel for IPv4inIPv6.

1. In the left navigation bar, click Advanced Setup > IP Tunnel > IPv4inIPv6 and then click Add. The following page
appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 100
 2. Enter a Tunnel Name. In the Mechanism field, the only option is DS-Lite.
3. Select the LAN and WAN interfaces associated with the tunnel you wish to establish.
4. In the AFTR (Address Family Transition Router) field, do either of the following:
l To configure manually, enter the remote address in the AFTR field.
l To configure automatically, select Automatic above the AFTR field.
5. Click Apply/Save to commit your changes.

Certificate
In this section, you can configure certificates (local and Trusted CA) for the gateway. For more information about certificates, refer
to the ITU X.509 standard.

Local
On this page, you can manage local certificates used to identify the gateway to other users. You can create a new certificate
request locally and have it signed by a certificate authority, or you can import an existing certificate. For additional info regarding
Public Key Infrastructure (PKI), refer to ITU-T X.509.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 101
Creating certificate requests

1. In the left navigation bar, click Advanced Setup > Certificate. The following page appears.

2. Click Create Certificate Request. The following page appears.

3. Enter your connection details, using the information provided in the table below.
4. Click Apply to complete the request.
5. Submit your certificate request to a certificate authority for signature.

Field Name Description

Certificate Name Enter a certificate name that describes the intended use of the certificate.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 102
Field Name Description
Common Name Enter the IP address (in dotted decimal notation), domain name, or email address. Browsers use this
information to verify your certificate is valid.
Organization Name Enter the name or the company or organization creating the request.
State/Province Enter the full name of the state or province where your organization's head office is located.
Name
Country/Region Select the country or region in which this certificate will be employed.

Importing a local certificate and private key

1. In the left navigation bar, click Advanced Setup > Certificate > Local. Then click Import Certificate. The following
page appears.

2. In the Certificate Name field, type "cpecert".

3. Paste the Certificate details between the BEGIN and END markers.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 103
 4. Paste the Private Key information between the BEGIN and END markers.
5. Click Apply to commit this certificate.

Trusted CA
On this page, you can import Trusted Certificates to identity other gateways to your gateway as a trusted source.

1. In the left navigation bar, click Advanced Setup > Certificate > Trusted CA. The following page appears.

2. To import a certificate, click Import Certificate. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 104
 3. In the Certificate Name field, type a descriptive name for this certificate. If you are using this certificate with TR-069,
the name must be "acscert".
4. Paste the certificate details between the BEGIN and END markers.
5. Click Apply to commit this certificate.

After you add one certificate, a Remove button appears on the Trusted CA landing page. Click this button to remove the current
certificate and replace it with a new one.

Power Management
Note: This feature is not currently supported.

Multicast
On this page, you can configure the multicast parameters.

1. In the left navigation menu, click Advanced Setup > Multicast. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 105
 2. Fill in the fields, using the information in the table below. The fields provided for the IGMP and MLD configurations
are largely the same.
3. To create or remove exceptions in the Group Exception List table, follow the instructions in "Managing group
exception lists".
4. Click Apply/Save to save and apply the settings.

Field Name Description

Source Specific Select whether a specific multicast source is used. Options are Disable and Enable. The default is
Multicast Disable.
Multicast Precedence Select whether IGMP packets are given priority handling and at what level. Options are:
l Enable: IGMP packets are prioritized using the multicast precedence value. The lower the
multicast precedence value, the higher that IGMP packets will be placed in the queue.
l Disable: IGMP packets are not prioritized. This is the default.
Multicast Strict Select whether to enforce strict key management rules. Options are Enable and Disable. The default is
Grouping Enforcement Disable.
IGMP Configuration and MLD Configuration sections
Default Version Enter the supported IGMP version. Options are 1 - 3.
Query Interval Enter the interval at which the multicast router sends a query messages to hosts, expressed in seconds.
If you enter a number below 128, the value is used directly. If you enter a number above 128, it is
interpreted as an exponent and mantissa.
Query Response Interval Upon receiving a query packet, a host begins counting down seconds, from a random number. When the
timer expires, the host sends its report.
Enter the maximum number of seconds that a host can pick to count down from.
Robustness Interval (Applies to IGMP configuration only) Enter the maximum response time within which the host must
respond to the Out of Sequence query from the router. The default is 10 seconds.
Last Member Query (Applies to MLD configuration only) Enter the maximum response time within which the host must
Interval respond to the Out of Sequence query from the router. The default is 10s.
IGMP uses this value when the router receives an IGMPv2 Leave report indicating at least one host wants
to leave the group. Upon receiving the Leave report, the router verifies whether the interface is
configured for IGMP Immediate Leave. If not, the router sends the out-of-sequence query.
Robustness Value Enter the value representing the complexity of the query. The greater the value, the more robust the
query. Options are 2 - 7.
Maximum Multicast Enter the maximum number of groups allowed. The default is 25 for IGMP and 10 for MLD.
Groups
Maximum Multicast Data Enter the maximum number of data sources allowed. Options are 1 - 24.
Sources (for IGMPv3)
Maximum Multicast Enter the maximum number of multicast groups that can be joined on a port or group of ports.
Group Members
Fast Leave Enable Select whether the IGMP proxy removes group members immediately without sending a query. Options
are:
l Enabled: Group members are removed immediately. This is the default.
l Disabled: Group members are removed after a query is sent and a response received.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 106
Managing group exception lists
You can manage exceptions for multicast groups using the IGMP Group Exception List or MLD Group Exception List tables. The
first two entries are created by default; you cannot change these entries.
To add an exception, type the IP address in the Group Address field, enter the mask information in the Mask / Mask bits field, and
then click Add.
To remove an exception, click the Remove check box next to it and then click the Remove Checked Entries button. The list
refreshes.
Click Apply / Save to implement your changes.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 107
Wireless
In this section, you can configure the wireless interface settings for your gateway, including basic and advanced settings, MAC
filtering, and wireless bridging.

Basic
On this page, you can configure basic features of the WiFi LAN interface. You can enable or disable the WiFi LAN interface, hide the
network from active scans, set the WiFi network name (also known as SSID) and restrict the channel set based on country
requirements.

1. In the left navigation bar, click Wireless. The following page appears, showing the information for the 5 GHz band.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 108
 2. If you want to view or configure the 2.4GHz band settings, click 2.4 GHZ Band in the left menu.
3. Modify the settings as desired, using the information provided in the table below.
4. (Optional) Define up to three virtual access points for guest access using the information from the Wireless -
Guest/Virtual Access Points section of the table below.
5. Click Apply/Save to commit your settings.

Field Name Description

Enable WiFi Button This option is selected by default. To disable the gateway's 2.4GHz button, clear the checkbox.
Enable Wireless This option is selected by default. To disable the wireless feature, clear the checkbox. All other fields on
the page are hidden.
Enable Wireless This option is disabled.
Hotspot 2.0
Hide Access Point Click to hide the access point SSID from end users and passive scanning.
Clients Isolation Click to prevent LAN client devices from communicating with one another on the wireless network.
Disable WMM Advertise Click to stop the wireless from advertising Wireless Multimedia (WMM) functionality. Selecting this option
can improve transmission performance for voice and video data.
Enable Wireless This option is enabled by default allowing multicast traffic to be forwarded across wireless clients. This
Multicast Forwarding option can improve the quality of video services such as IPTV. To disable Wireless Multicast Forwarding
(WMF), clear the checkbox.
SSID (Optional) Enter the WiFi SSID. For security purposes, this identifier should be unique for your system. If
your gateway is connected to an ACS, it is recommended that SSID names be be 1 - 32 characters long.
Special characters are accepted.
BSSID Displays the Basic Service Set Identifier (BSSID), the MAC address assigned to the wireless router.
Country This option is set by default and cannot be changed. The wireless channel adjusts to the frequency
provision for the selected country.
Country RegRev Enter the revision number of the regulations being followed for the selected country. The default is 0.
Max Clients Enter the maximum number of clients that can access the route wirelessly. Options are 1 through the
value set in the Global Max Clients field on the Wireless > Advanced page. The default is 20.
Note: Before you can change this setting, you must change the Global Max Clients setting.
Wireless - Guest/Virtual Access Points section
Enabled Click to enable a virtual wireless access point for guest access.
SSID Enter the wireless SSID for guests to use.
Hidden Click to prevent the SSID from being broadcast publicly.
Isolate Clients Click to prevent client PCs from communicating with one another.
Enable WMM Advertise Click to stop the wireless from advertising Wireless Multimedia (WMM) functionality.
Enable WMF Click to disable Wireless Multicast Forwarding (WMF).
Enable HSPOT This option is disabled.
Max Clients Enter the maximum number of clients that can connect to this access point.
BSSID Displays the Basic Service Set Identifier or N/A .

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 109
Security
On this page, you can configure network security settings of a wireless LAN interface, either by using the WiFi Protected Setup (WPS)
method or by setting the network authentication mode. For WiFi Protected Setup, the following methods are supported:
l PIN entry: Mandatory method of setup for all WPS-certified devices. Options are:
l Enter STA PIN: You must enter the (input) station PIN from the client.
l Use AP PIN: The access point (AP) generates the device PIN.
l PBC (Push Button Configuration): Uses a simulated push button in the software. (This is an optional method on
wireless clients.)
Note: To use the PIN method, you need a Registrar (access point/wireless gateway) to initiate the registration between a new
device and an active access point/wireless gateway. The PBC method may also need a Registrar when used in a special case where
the PIN is all zeros.
Seven types of network authentication modes are supported: Open, Shared, 802.1X, WPA2, WPA2-PSK, Mixed WPA2/WPA, and Mixed
WPA2/WPA-PSK.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 110
 1. In the left navigation bar, click Wireless > 5 GHz Band or 2.4 GHz Band > Security. The following page appears.

2. Modify the settings as needed, using the information provided in the field description table below and in the sections
that explain each authentication method.
The fields in the WPS Setup section are described in the following table.

Field Name Description

Enable WPS This option is enabled by default. To disable WiFi Protected Setup, select Disabled. When you
select Enabled, additional fields appear.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 111
 Field Name Description
Add Client (Available for WPA-PSK, WPA2-PSK and Open Network Authentication methods) Select the
method for generating the WPS PIN. Options are:
l Enter STA PIN: Type the input station PIN for the client in the field below the radio
button. Click Add Enrollee. The PIN is verified.
l Use AP PIN: The entry field and the Set Authorized Station MAC field disappear.
Note: If the PIN and Set Authorized Station MAC fields are left blank, the PBC (push-button)
mode is automatically made active.
Set Authorized (Available only when Enter STA PIN is selected) Enter the MAC address of the authorized (input)
Station MAC station in format: xx:xx:xx:xx:xx:xx.
Set WPS AP Select how security is assigned to clients.
Mode l Configured: The gateway assigns security settings to clients. This is the default.
l Unconfigured: An external client assigns security settings to the gateway.
Device PIN This value is generated by the access point.

3. In the Manual Setup AP section, select the SSID for the device that you want to configure. The default is the 5 GHz
wireless band defined for your gateway.
4. Select the Network Authentication method and then fill in the fields that appear. The default method is Mixed
WPA2 / WPA-PSK. Detailed instructions are provided for each method in the following sections:
l "Open and Shared Authentication"
l "802.1X Authentication"
l "WPA2 and Mixed WPA2/WPA Authentication"
l "WPA2-PSK and Mixed WPA2/WPA-PSK Authentication"
5. Click Apply/Save to commit your changes.

Open and Shared Authentication

The same configuration fields apply for both Shared and Open authentication types except that WEP Encryption is enabled by
default for the Shared method.
The following fields appear when you select Open or Shared in the Network Authentication field and WEP Encryption is enabled.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 112
Modify the fields as needed and then click Apply/Save.

Field Name Description

WEP Encryption Select the Wired Equivalent Privacy (WEP) mode. Options are Enabled and Disabled. The default is
Disabled for Open authentication and Enabled for Shared authentication.
Encryption Strength Select the length of the encryption method. Options are 128-bit and 64-bit. 128-bit is the default and is
the more robust option for security.
Current Network Key Select which of the defined keys is presently in effect.
Network Key 1-4 Enter up to four encryption keys using the on-screen instructions to achieve the desired security
strength.

802.1X Authentication
The following fields appear when you select 802.1X in the Network Authentication field. WPS is disabled for this method.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 113
Modify the fields as needed, using the information provided in the table below, and then click Apply/Save.

Field Name Description

RADIUS Server IP Enter the IP address of the RADIUS (Remote Authentication Dial In User Service) server associated with
address your network. RADIUS server is used to authenticate the hosts on the wireless network.
RADIUS Port Enter the port number for the RADIUS server. Port 1812 is the default and the current standard for RADIUS
authentication per the IETF RFC 2865. Older servers may use port 1645. Options are 1 - 65535.
RADIUS Key (Optional) Enter the encryption key if needed to authenticate to the specified RADIUS server.
WEP Encryption This option is set to Enabled and cannot be changed. It enables WEP (Wired Equivalent Privacy) mode.
Encryption Strength Select the length of the encryption method. Options are 128-bit and 64-bit. 128-bit is the default and is
the more robust option for security.
Current Network Key Select which of the defined keys is presently in effect. The default is 2.
Network Key 1-4 Enter up to two encryption keys using the on-screen instructions to achieve the desired security strength.
Network Keys 1 & 4 are set automatically and cannot be changed.

WPA2 and Mixed WPA2/WPA Authentication

The following fields appear when you select WPA2 or Mixed WPA2/WPA in the Network Authentication field.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 114
Modify the fields as needed, using the information provided in the table below, and then click Apply/Save.

Field Name Description

Protected Management Select whether management frames are protected. Options are Disabled, Capable, and Required. The
Frames default is Disabled.
WPA2 Preauthentication Select whether clients can pre-authenticate with the gateway while still connected to another AP.
Options are Enabled and Disabled. The default is Disabled.
Network Re-Auth Interval Enter the interval at which the client must re-authenticate with the gateway. The default is 36000
seconds (10 hours).
WPA Group Rekey Interval Enter the frequency at which the gateway automatically updates the group key and sends it to
connected LAN client devices. Options are 0 - 65535 seconds. The default is 0.
RADIUS Server IP address Enter the IP address of the RADIUS (Remote Authentication Dial In User Service) server associated with
your network.
RADIUS Port Enter the port number for the RADIUS server. Options are 1 - 65535. Port 1812 is the default and is
the current standard for RADIUS authentication per the IETF RFC 2865. Older servers may use port
1645.
RADIUS Key (Optional) Enter the encryption key needed to authenticate to the specified RADIUS Server.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 115
Field Name Description
WPA/WAPI Encryption Select the encryption standard. This field is displays the option most compatible with the selected
network authentication method. Options are:
l AES: Advanced Encryption Standard. This is the default.
l TKIP+AES: AES combined with TKIP (Temporary Key Integrity Protocol) allows access by
either standard.
WEP Encryption This option is set to Disabled and cannot be changed.

WPA2-PSK and Mixed WPA2/WPA-PSK Authentication

The following fields appear when you select WPA2-PSK or Mixed WPA2/WPA-PSK in the Network Authentication field.

Modify the fields as needed, using the information provided in the table below, and then click Apply/Save.

Field Name Description

Protected Management Select whether management frames are protected. Options are Disabled, Capable, and Required. The
Frames default is Disabled.
WPA/WAPI passphrase Enter the security password to be used by this security configuration. When you click Click here to
display, the passphrase appears in a separate window.
WPA Group Rekey Enter the frequency at which the gateway automatically updates the group key and sends it to
Interval connected LAN client devices. The default is 0.
WPA/WAPI Encryption Select the encryption standard. This field is displays the option most compatible with the selected
network authentication method. Options are:
l AES: Advanced Encryption Standard.
l TKIP+AES: AES combined with TKIP (Temporary Key Integrity Protocol).
WEP Encryption This option is set to Disabled and cannot be changed. It disables WEP (Wired Equivalent Privacy) mode.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 116
MAC Filter
On this page, you can configure whether wireless clients are allowed to access the wireless network of the wireless gateway.

1. In the left navigation bar, click Wireless > MAC Filter. The following page appears.

2. In the Select SSID field, select the access point that you want to configure.
3. Select the MAC Restrict Mode. Options are:
l Disabled: Disable wireless MAC address filtering. This is the default.
l Allow: Allow the wireless clients in the MAC Address list to access the wireless network.
Note: For this option to work, you must add at least one MAC address to this page.
l Deny: Reject requests from the wireless clients in the MAC Address list to access the wireless network.
4. To add a MAC Address to the filter list:
a. Click Add. The following page appears.

b. Enter the MAC address of the wireless client.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 117
 c. Click Apply/Save to save the address to the list. You are returned to the Wireless - MAC Filter landing
page.
5. To remove a MAC address from the list, click the Remove check box next to it and then click the Remove button. The
list refreshes.

Wireless Bridge
On this page, you can configure the wireless bridge features of the wireless LAN interface.

1. In the left navigation menu, click Wireless > Wireless Bridge. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 118
 2. Modify the fields as needed, using the information provided in the table below.

Field Name Description

AP Mode Select whether to enable or disable access point (AP) functionality. Options are:
l Wireless Bridge: Disables AP functionality.
l Access Point: Enables AP functionality. Wireless bridge functionality is still
available and wireless stations can associate to the AP. Thisi s the default.
Bridge Restrict Enable or disable the bridge restrict function for MAC addresses in the Remote Bridges MAC
Address field. Options are:
l Enabled: Allow only those bridges selected in the Remote Bridges MAC Address table to
access the wireless LAN. This is the default.

l Enabled (Scan): Allow only those bridges selected in the Remote Bridges MAC Address
table to access the wireless LAN but the scanning feature is active.
l Disabled: Disable the wireless MAC address filtering function. Any wireless bridge can
access the wireless LAN.
Remote Bridges Enter up to four MAC addresses for the remote bridges that are allowed to access the wireless
MAC Address LAN.

3. Click Apply/Save to save your settings.

Advanced
On this page, you can configure the advanced features of the wireless LAN interface. You can select a particular channel on which to
operate, force the transmission rate to a desired speed, set the fragmentation threshold, the RTS threshold, the wakeup interval
for clients in power-save mode, and more.
Note: The default settings work for most environments. It is recommended that only experienced users change settings on this
page.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 119
 1. In the left navigation bar, click Wireless > Advanced. The following page appears.

2. Modify the fields as needed, using the information in the following table.
3. Click Apply/Save to commit your changes.

Field Name Description

Band The only option for this field is the band selected in the left menu.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 120
Field Name Description
Channel Select the Wi-Fi channel you want to use. The current channel number displays to the right of the field.
For the 5GHz band, options are Auto and 36 through 157. For the 2.4GHz band, options are Auto and 1 -
7. The default is Auto.
All devices in your wireless network must use the same channel in order to work correctly.
Auto Channel Timer (min) Enter the frequency (in minutes) at which the gateway scans channels for interference. If a threshold of
inference is detected, a new channel will be selected automatically. Options are 0 - 65535 minutes.
The default is 15 minutes.
MIMO-OFDM This option is set to On and cannot be changed.
Bandwidth Select the operating bandwidth. Options are 20 MHz, 40 MHz, and, for the 5 GHz band, 80 MHz. The
default is 20MHz. The current bandwidth setting displays to the right of the field.
Control Sideband This option is not available. The value is set by the system and cannot be changed.
802.11n Rate Select the desired physical transmission rate. This option is set to Auto (the Auto-Fallback feature is
enabled) and cannot be changed. This enables the Auto-Fallback feature which allows the gateway to
automatically use the fastest possible data rate. Auto-Fallback will negotiate the best possible
connection speed between the gateway and a wireless client.
802.11n Protection Select whether to enable 802.11n and legacy clients to both work effectively on the network. Options
are:
l Auto: Provides maximum security but produces a noticeable impact on throughput. With
this option, RTS/CTS behavior permits legacy clients to become aware of 802.11n transmit
times, but decreases overall throughput. This is the default.
l Off: Provides better throughput.
Support MIMO client only Select whether to restrict MIMO clients from accessing the gateway. Options are On and Off. The
default is Off.
RIFS Advertisement RIFS (Reduced InterFrame Speed) is the time in micro seconds by which the multiple transmissions from
a single station is separated. This option Improves performance by reducing dead time required
between OFDM transmission. Options are Auto and Off. The default is Auto.
OBSS Co-Existence Coexistence of Overlapping Basic Service Sets (OBSS) prevents overlapping in the 20 MHz and 40 MHz
frequencies. Options are:
l Enable: The gateway automatically reverts to 20 MHz channel bandwidth when another
WiFi network within 2 channels of its own channel is detected or when a client device
with its 40 MHz Intolerant bit set is detected.
l Disable: The gateway advertises and operates in 40 MHz mode regardless of how other
nearby networks are configured. This is the default.
RX Chain Power Save Select whether power-save mode is enabled. Options are Disable and Enable. The default is Enable.
Note: Before setting this parameter, make sure that 802.11n/EWC is set to Auto.
RX Chain Power Save Enter the number of minutes that will elapse before quiet time begins. The default is 10 minutes.
Quiet Time
RX Chain Power Save PPS Enter the throughput threshold (in seconds) for when the router engages power save mode after the
quiet time period has elapsed. The default is 10 seconds.
54g Rate This option is set to 6 Mbps and cannot be changed.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 121
Field Name Description
Multicast rate Select the multicast transmission rate for the network according to the speed of your wireless network.
Select from a range of transmission speeds or select Auto to have the gateway automatically use the
fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback will negotiate the best
possible connection speed between the gateway and a wireless client.
Options are Auto and 6 - 54 Mbps. The default value is Auto.
Basic Rate Select the basic transmission rate ability for the AP. Options are Default, All ,1 & 2 Mbps, and 1 & 2 &
5.5 & 6 & 11 & 12 &24 Mbps. The default is Default.
Fragmentation Threshold Enter the size at which packets will be fragmented into smaller units. The primary consideration for this
setting is the size/capability of the circuit. Options are 256 - 2346 bytes. The default is 2346 bytes.
Note: A high packet error rate is an indication that a slightly increased fragmentation threshold is
needed. When possible, the default value of 2346 bytes should be maintained. Poor throughput is a
likely result of setting this threshold too low.
RTS Threshold The gateway sends Request to Send (RTS) frames to a particular receiving station and negotiates the
sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS)
frame to acknowledge the right to begin transmission.
If a packet is smaller than this setting, the WLAN client hardware does not invoke its RTS/CTS
mechanism. Options are 256 - 2347 bytes.
The default value of 2347 (disabled) should be left in place unless you encounter inconsistent data
flow. In that case, make small reductions to this value until the issue is resolved.
DTIM Interval Enter the Delivery Traffic Indication Message (DTIM or Beacon rate) countdown variable used to indicate
when the next window is available to client devices for listening to buffered broadcast and multicast
messages. Options are 1 - 255. The default is 1.
Beacon Interval Beacon information packets are sent from a connected device to all other devices where it announces
its availability and readiness. A beacon interval is the period of time (sent with the beacon) that the
device waits before sending the beacon again.
Enter the time interval (in milliseconds) between beacon transmissions. Options are 1 - 65535 ms. The
default is 100 ms, which is recommended.
Global Max Clients Enter the maximum number of clients that can assess this wireless network at one time. The maximum
for 5 GHz is 80; the maximum for 2.4 GHz is 128. The default is the maximum for each band.
Note: You must change this field before you can change the Max Clients on the Wireless > Basic. page.
Xpress™ Technology Select whether to enable Xpress Technology, a special accelerating technology for IEEE802.11g. Options
are Enable and Disable. The default is Enable.
Transmit Power Level Select the level of power used for transmittals. Options range from 4 dBm (2mw) to 26 dBm (400 mw).
The default is 26 dBm (400 mw).
WMM (WiFi Multimedia) This technology allows multimedia services (audio, video and voice packets) to get higher priority for
transmission. Options are Auto, Enabled, and Disabled. The default is Enabled.
Warning: If you disable this option, all QoS queues and classifications defined for the wireless network
are also disabled.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 122
Field Name Description
WMM No The acknowledge policy used at the MAC level. Enabling this option allows better throughput but, in a
Acknowledgment noisy RF environment, higher -963 error rates may result. The default is Disabled, meaning that an
acknowledgment packet is returned for every packet received. This provides a more reliable
transmission but increases traffic load, which decreases performance. Disabling the acknowledgment
can be useful for Voice, for example, where speed of transmission is important and packet loss is
tolerable to a certain degree. Options are Enabled and Disabled. The default is Disabled.
WMM APSD APSD (Automatic Power Save Delivery) is an automatic power saving feature. Enabling ensures very low
power consumption. WMM Power Save is an improvement to the 802.11e amendment, adding advanced
power management functionality to WMM. Options are Enabled and Disabled. The default is Enabled.
Beamforming Select to concentrate the transmission signal at the gateway location. This results in a better signal and
Transmission (BFR) potentially better throughput. Options are Disabled, SU BFR, and MU BFR. The default is Disabled.
Beamforming Reception Select to concentrate the transmission signal at the gateway location. Options are Disabled, SU BFE,
(BFE) and MU BFE. The default is Disabled.
Band Steering Select whether to detect if the client has the ability to use two bands. When enabled, the less-
congested 5GHz network is selected (by blocking the client's 2.4GHz network). Options are Disabled and
Enabled. The default is Disabled.
Enable Traffic Scheduler Select whether to enable scheduling of traffic to improve efficiency and increase usable bandwidth for
some types of packets by delaying other types. Options are Disable and Enable. The default is Disable.
Airtime Fairness Select how the gateway will manage the receiving signal with other devices. Options are Disable and
Enable. The default is Enable.

Station Info
On this page, you can view the authenticated wireless stations and their status.
In the left navigation menu, click Wireless > Station Info. The following page appears.

To update the data, click Refresh.

Wifi Insight
On this page, you can configure the WiFi Insight system.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 123
 1. In the left navigation menu, click Wireless > Wifi Insight. The following page appears. You can also reach this page by
clicking Wireless > Wifi Insight > Configure.

2. In the Sample Interval section, select the number of seconds for sampling to occur. Options are 5, 10, 15, and 20
seconds. The default is 5 seconds.
3. In the Start/Stop Data Collection section, configure the data sample:
a. Click Start collecting data every.
b. Select the days of the week when the data should be collected.
c. In the From and To fields, enter the start and end times for collection.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 124
 4. In the Database Size section, configure the database size limits:
a. In the Database Size field, enter the maximum size for the database file where the collected data will
be stored. The default is 2 MB.
b. (Optional) Select whether to stop data collection when the maximum size is reached. Options are
Overwrite Older Data and Stop Datacollection. The default is Overwrite Older Data.
5. (Optional) In the Counters section, clear any counter options that you do not need. The default is to collect all
counters.
6. Click Submit to save the configuration.
7. To export a database, in the Export Database section:
1. Click Save Database to File. The open/save dialog box appears.
2. Click OK to save or click Open and OK to view.

Site Survey
On this page, you can view signal strength and other details for your wireless networks.

1. In the left navigation menu, click Wireless > Wifi Insight > Site Survey. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 125
 2. In the first field above the chart, select the wireless network that you want to review.
3. In the Select Channel field, select the channel that you want to review.
4. In the Select Bandwidth field, select the bandwidth.
5. Click Scan. The page refreshes to show the requested information.

Channel Statistics
On this page, you can view signal strength, channel capacity, interference, and other details for specific channels.
In the left navigation menu, click Wireless > Wifi Insight > Channel Statistics. The following page appears.

Metrics
On this page, you can view glitch counter, chanim, associated stations, and packet queue statistics for your wireless networks.
In the left navigation menu, click Wireless > Wifi Insight > Metrics. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 126
SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 127
Voice
In this section, you can view status, enable features, and configure settings for VoIP.

VoIP Status
On this page, you can view status data for your SIP accounts.
In the left navigation menu, click Voice. The following page appears.

In the Registration Status field, Up means registered successfully, Down means unregistered, Disabled means the account is not
enabled.

SIP Basic Setting

On this page, you can configure basic SIP settings including proxies and registrars.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 128
 1. In the left navigation menu, click Voice > SIP Basic Setting. The following page appears.

2. Modify the fields as needed, using the information in the following table.
3. Click Apply to implement your changes.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 129
The fields on this page are defined below.

FIELD NAME DESCRIPTION

Bound Interface Name Select the bound interface name. Options are LAN, Any_WAN, and any other interfaces configured for
your network. The default is Any_WAN.
Country Select the country or region for this voice configuration.
SIP local port Enter the local port of the gateway which is the SIP UA (user agent) port. Options are 1 - 65535. The
default value is 5060.
Use SIP Proxy for Select this option if your DSL gateway uses a SIP proxy. SIP proxy allows other parties to call DSL gateway
Account 1/2 through it. When you select this option, the following fields appear:
l SIP Proxy: Enter the IP address of the proxy.
l SIP Proxy port: Enter the port that this proxy is listening on. The default port value is 5060.
Use SIP Outbound Proxy Some network service providers require the use of an outbound proxy. This is an additional proxy, through
for Account 1/2 which all outgoing calls are directed. In some cases, the outbound proxy is placed alongside the firewall
and it is the only way to let SIP traffic pass from the internal network to the Internet. When you select
this option, the following fields appear:
l SIP Outbound Proxy: Enter the IP address of the outbound proxy.
l SIP Outbound Proxy port: Enter the port that the outbound proxy is listening on. By default, the
port value is 5060.
Use SIP Registrar For Select this option to register your user ID on the SIP registrar of the proxy. SIP registrar works with SIP
Account 1/2 proxy, allowing other parties to call DSL gateway through it. When you select this option, the following
fields appear:
l SIP Registrar: Enter the IP address of the SIP registrar.
l SIP Registrar port: Enter the port that SIP registrar is listening on. By default, the port value is
5060.
Use Backup SIP Proxy Select this option if your DSL gateway uses a backup SIP proxy. When you select this option, the following
For Account 1/2 fields appear:
l SIP Proxy: Enter the IP address of the backup proxy.
l SIP Proxy port: Enter the port that this backup proxy is listening on. The default port value is
5060.
Use Backup SIP Select this option if your DSL gateway uses a backup SIP outbound proxy. When you select this option, the
Outbound Proxy For following fields appear:
Account 1/2 l SIP Outbound Proxy: Enter the IP address of the backup outbound proxy.
l SIP Outbound Proxy port: Enter the port that the backup outbound proxy is listening on. By
default, the port value is 5060.
Use Backup SIP Select this option to register your user ID on the backup SIP registrar of the proxy. When you select this
Registrar For Account option, the following fields appear:
1/2 l SIP Registrar: Enter the IP address of the backup SIP registrar.
l SIP Registrar port: Enter the port that backup SIP registrar is listening on. By default, the port
value is 5060.
SIP Account table
Account Enabled If this option is not selected, the corresponding account is disabled and you cannot use it to initiate or
accept calls.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 130
FIELD NAME DESCRIPTION
Polarity Reverse Enable Enable or disable this function by selecting and clearing the check boxes.
Authentication name Enter the user name.
Password Enter the password.
Cid Name Enter the user name that should display as the caller ID name.
Cid Number Enter the number that should display as the caller ID number.
Note: In some cases, this number must be the SIP authentication user ID.
Codec line settings table
Codec -line 1 / 2 The 1st and 5th columns identify the codec. The most common codec IDs display by default.
ptime [ms] The 2nd and 6th columns identify the packetization time (ptime) which is the length of the digital voice
segment that each packet holds. Enter the ptime in milliseconds. The default is 20 millisecond packets.
Note: Selecting 10 millisecond packets improves voice quality; less information is lost, but there is more
load on the network traffic.
Priority The 3rd and 7th columns identify the priority of each codec. The priority of the codec is defined from up
to down. Codecs define the method of relaying voice data. Different codecs have different
characteristics, such as data compression and voice quality. For example, G723 is a codec that uses
compression, therefore, it is good for use where the bandwidth is limited. However, its voice quality is not
as good as other codecs, such as the G711. If you do not select a codec (accepting the default value), the
gateway chooses the codec automatically.
Enable The 4th and 8th columns contain the Enable check boxes. Click to enable a particular codec.

SIP Advanced Setting

On this page, you can configure the advanced VoIP features.

1. In the left navigation menu, click Voice > SIP Advanced Setting. The following page appears. Detailed information
about each VoIP line is shown in the top table.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 131
 In the bottom section are settings for Fax, QoS, caller ID, service offer models and so on.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 132
 2. Modify the fields as needed, using the information provided in the table below.
3. Click Apply to implement the settings.

The fields on this page are defined below.

FIELD NAME DESCRIPTION

Line The VoIP line you want to configure.
Call waiting Select to enable call waiting notification. When users hear the call waiting tone during a call, they press
FLASH to put the first call on hold and to answer the second call. Pressing FLASH again switches back to
the previous call.
Note: Call forward feature settings (Busy or All) take priority over the call waiting feature. The Call
waiting feature is ignored on new incoming calls if there is already a call on hold or in conference.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 133
FIELD NAME DESCRIPTION
Unconditionally Call Enter the number to which you want all incoming calls to be forwarded.
forwarding number
Busy Call forwarding Enter the number to which you want all incoming calls to be forwarded when the line is busy.
number
No Answer Call Enter the number to which you want all incoming calls to be forwarded when the calls are not answered.
forwarding number
Options Time Enter the time interval for sending the Options message.
Forward unconditionally Select to enable unconditional forwarding.
Forward on "busy" Select to enable forwarding when the line is engaged.
Forward on "no answer" Select to enable forwarding when a call is not answered.
Anonymous call blocking Select to block anonymous calls. Users can dial *77 to enable this feature and dial *87 to disable it.
Anonymous calling Select to enable using an anonymous name as a call number when calling out. Users can dial *68 to
enable this feature and dial *82 to disable it.
Anonymous calling mode Select the anonymous calling mode. Options are Display anonymous or All anonymous.
DND Select to reject all incoming calls. Users can dial *78 to enable this feature.
Enable Call Return Select to enable this function.
Call Transfer Select to enable transferring calls either manually or automatically.
Call conference Select to enable multiple extensions to join a single call.
Warm Line Select to enable the warm line feature which configures a line to dial a specific number after a short
delay (entered in seconds).
Warm Line URI If using the warm line feature, enter the URI to which the line should connect.
Warm Line Delay Timer Enter the number of seconds before an incoming call to the warm line is transferred.
Fax Setting section
Fax Negotiate Mode Select the negotiation mode. Options are Auto_switch, Negotiate, and V.152. The default is Auto_
switch.
Bypass Codec Select the bypass codec. Options are G711_A , G711_MU, and T.38. The default is Auto_switch.
Enable T38 redundancy Select to enable this function.
support
Enable vbd redundancy Select to enable this function.
support
Settings section
Enable VAD support This option is enabled by default. To disable VAD support, clear the checkbox. Select the VAD mode in
signal value. Options are None, Silencsupp, and annexa/annexb/vad. The default is None.
Enable RTCP Flow Ctrol Select to enable RTCP flow control for improved quality of service.
Enable Echo Cancellation This option is enabled by default. To disable echo cancellation for improved quality of service, clear the
checkbox..
Enable # to ASCII Select to enable conversion of numbers to their ASCII equivalents.
Enable call waiting calid. Select to display the caller ID for a waiting call.
SIP Timer Setting section

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 134
FIELD NAME DESCRIPTION
Registration Expire Enter the registration expire timeout. The default is 172800 (48 hours).
Timeout
Session Expire Time Enter the time interval for closing a conversation. The default is 86400 (24 hours).
Min Session Expire Time Enter the minimum interval for closing a conversation. This value must be 90 seconds or greater.
Digitmap Setting section
VoIP DialPlan Setting Enter the VoIP dial plan parameters. If a user-dialed number matches it, the number is processed by the
gateway immediately.
QoS Setting section
DSCP for SIP Select the DSCP mark for SIP. The default is DEFAULT (000000).
DSCP for RTP Select the DSCP mark for RTP. The default is DEFAULT (000000).
Payload Setting section
RFC2198 Payload Value Enter the RFC2198 payload value. Options are 97 - 127.
(range 96~127)
DTMF Relay Setting Select the DTMF transmit method. Options are:
l InBand: DTMF events are mixed with user voice in RTP packet.
l RFC2833: Use RTP packet to encapsulate DTMF events, as specified in RFC 2833.
l SIP Info: Use SIP INFO message to transmit DTMF digits.
Call ID Setting section
Caller ID send Delay time Enter the number of milliseconds that the system will delay before sending the caller ID. Options are
500 - 1500 ms. The default is 600 milliseconds.
Caller ID Message Type Select the message format for the caller ID. Options are FSK-MDMF, FSK-SDMF, and DTMF. The default is
FSK_MDMF.
FSK modulation Mode (Appears when an FSK value is selected in the Caller ID Message Type field) Select the modulation
mode for FSK message types. Options are BellcoreGen, V23Gen, and V23UK.
Transport Setting section
SIP Transport Protocol Select the transport protocol to use for SIP signaling. Note that the SIP proxy and registrar need to
support the protocol you select. Options are UDP and TCP. The default is UDP.
SIP Extends section
PRACK (100rel) Select to enable provisional responses. Options are DISABLE, SUPPORTED, and REQUIRED. The default is
SUPPORTED.
Agent Header Enter the agent name that you want displayed to users in the response header.
Service Offer Setting section
Complementary business Options are Local model , Server model , IMS model , and Undefined. The default is Local model .
models
If you select IMS model, the ETSI Malicious call tracing field appears. To enable malicious call tracing
option, click the checkbox.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 135
SIP Star Code Setting
On this page, you can set the numbers that are used with the * key to enable and disable various features.

1. In the left navigation menu, click Voice > SIP Star Code Setting. The following page appears.

2. Enter the numbers that you want assigned to various features. Users press the star (*) key and then enter these
numbers to enable or disable the various calling features.
3. Click Apply to implement your settings.

SIP Extra Setting

On this page, you can set the ring tones and their durations.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 136
 1. In the left navigation menu, click Voice > SIP Extra Setting. The following page appears.

2. Modify the fields as needed, using the information in the table below.
3. Click Apply to implement the settings.

The fields on this page are defined below.

Field Description
Line The VoIP line that you want to configure.
Dial tone time Enter the number of seconds that the dial tone will persist. Options are 10 - 20 seconds. The default is 15
seconds.
Busy tone time Enter the number of seconds that the busy tone will persist. Options are 30 - 180 seconds. The default is 40
seconds.
Inter digit time Enter the number of seconds allowed between dialing individual digits. The valid range is 1 - 5 seconds. The
default is 5 seconds.
Offhook warning Enter the number of seconds that the off-the-hook warning tone will persist. Options are 30 - 180 seconds. The
tone time default is 60 seconds.
Ringback tone Enter the number of seconds that the ringback tone will persist. Options are 30 - 180 seconds. The default is 80
time seconds.
T digit timer Enter the maximum number of seconds that the system waits to dial after the last digit has been entered. The
default is 4 seconds.
Short digit timer Enter the maximum number of seconds allowed between dialed digits. The default is 4 seconds.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 137
SIP Debug Setting
On this page, you can configure the debugging settings.

1. In the left navigation menu, click Voice > SIP Debug Setting. The following page appears.

2. Modify the fields as needed, using the information in the table below.
3. Click Apply to implement the settings.

The fields on this page are defined below.

Field Description
Vodsl Console Log (Optional) Select the level of detail stored in the VODSL Console log. Options are Error, Notice, and Debug.
Level

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 138
Field Description
System Log Level (Optional) Select the level of detail stored in the System log. Options are SPY_GEN_INFO, SPY_FNENTER,
SPY_EVENT, SPY_MINOR_ERR, SPY_MAJOR_ERR, SPY_FATAL_ERR, and SPY_LEVEL_OFF. The default is
SPY_EVENT.
Protocol Stack Log (Optional) Select the level of detail stored in these logs. Options are SPY_GEN_INFO, SPY_FNENTER, SPY_
Level EVENT, SPY_MINOR_ERR, SPY_MAJOR_ERR, SPY_FATAL_ERR, and SPY_LEVEL_OFF. The default is SPY_
Call Control Log Level MAJOR_ERR.
Register Log Level
DSP Log Level
Tele Log Level
Dialplan Log Level
Restart Log Level
Master Level Control settings section
Master Level (Optional) Select the lowest level of log entries for VoIP. When debugging, this level must be lower than
the levels selected in the other fields in this section. Options are Emerg, Alert, Crit, Error, Warn, Notice,
Info, and Debug. The default is Crit.
LOGIC (Optional) Select the level of logging for these modules. Options are Emerg, Alert, Crit, Error, Warn,
PROVISION Notice, Info, and Debug. The default is Error.
VOICE
AGENT
SIP log server IP Enter the IP address of the server where the SIP logs should be stored.
address
SIP log server port Enter the port number for the same server.
Gain Settings table (Optional) Select the gain levels for incoming and outgoing transmissions for each line. Options are -14 to 6.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 139
SIP Black Filter
On this page, you can configure the black filtering settings.

1. In the left navigation menu, click Voice > SIP Black Filter. The following page appears.

2. In the black list column, enter the phone number that you want to block.
3. To activate the new entry, click the enable checkbox next to it.
4. Click Apply to implement the settings.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 140
Diagnostics
Line performance diagnostic tools are supported by your SmartRG gateway. Three legs of the data path are included in the available
tests: LAN connectivity, DSL connectivity, and Internet connectivity tests.

Diagnostics
On this page, you can test the connection to your local network, the connection to your DSL service provider, and the connection to
your Internet service provider.

1. In the left navigation bar, click Diagnostics. The following page appears, showing information about the connection
encountered by the gateway.

2. To run a test (and refresh the data), click the appropriate Test button.
The table is updated with fresh diagnostic information regarding connection integrity.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 141
 3. To test another connection, click Next Connection. The data refreshes and the Previous Connection button
appears.
4. If a test fails, click the Help link located in the last column to learn more about what is being tested and what actions
you can take.

Ethernet OAM
On this page, you can view diagnostics regarding your VDSL PTM or Ethernet WAN connection. Fault Management is compliant with
IEEE 802.1ag for Connectivity Fault Management.

1. In the left navigation bar, click Diagnostics > Ethernet OAM. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 142
 2. To enable Ethernet Link OAM (802.3ah):
a. Click the Enabled checkbox. Additional fields appear.

b. Modify the fields as needed, using the information in the Ethernet Link OAM (802.3ah) section of the
table below.
3. To enable Ethernet Service OAM (802.1ag/Y.1731):
a. Click the Enabled checkbox. Additional fields appear showing values for 802.1ag. To configure Y.1731,
click the Y.1731 radio button. The page refreshes.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 143
 b. Modify the fields, using the information provided in the Ethernet Service OAM (802.1ag/Y.1731)
section of the table below.
4. Click Apply/Save to commit your changes.
5. To run a loopback test, enter a MAC address in the Target MAC field and click Send Loopback at the bottom of the
page. The results appear in the Loopback Result row of the table.
6. To run a linktrace test, enter a MAC address in the Target MAC field and click Send Linktrace at the bottom of the
page. The results appear in the Linktrace Result row of the table.

Field Name Description

Ethernet Link OAM (802.3ah) section
WAN Interface Select the WAN interface that you want to test.
OAM ID Enter the ID of this OAM configuration. Only positive numbers are allowed.
Auto Event Click to enable automatic reporting of events.
Variable Retrieval Click to enable on-demand link diagnostics, including bit-error-rate approximation.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 144
Field Name Description
Link Events Click to enable reporting of critical conditions that may cause link failure.
Remote Loopback Click to enable on-demand link diagnostics, including bit-error-rate approximation.
Active Mode Click to enable this feature.
Ethernet Service OAM (802.1ag/Y.1731) section
WAN Interface Select the WAN interface that you want to test.
MD Level (Appears for the 802.1ag option only) Select the domain level for this maintenance domain. Options are 0 -
7. The larger the domain, the higher the value you should select.
MD Name (Appears for the 802.1ag option only) Enter the name of the maintenance domain, e.g., Broadcom.
MA ID (Appears for the 802.1ag option only) Enter the maintenance association ID, e.g., BRCM.
MEG Level (Appears for the Y.1731 option only) Enter the level of the maintenance entity group.
MEG ID (Appears for the Y.1731 option only) Enter the ID of the MEG.
Local MEP ID Enter the ID of the local maintenance entity group end point.. Options are 1 - 8191. The default is 1.
Local MEP VLAN ID Enter the VLAN ID of the local MEP. Options are 1 - 4094. The default is -1 (no VLAN tag).
CCM Transmission Click to enable continuity check message transmission.
Remote MEP ID Enter the ID of the remote MEP. Options are 1 - 8191. The default is -1 (no remote MEP).
Loopback and Linktrace Test section
Target MAC Enter the MAC address for the test, e.g., 02:10:18:aa:bb:cc.
Linktrace TTL Enter the maximum number of hops allowed. Optinons are 1- 233. The default is -1 (no limit).
Loopback Result Displays the results of the loopback test.
Linktrace Result Displays the results of the linktrace test.

Diagnostic Tools
In this section, you can ping or trace the communication route, and start or stop your DSL connection.

Ping
On this page you can ping a server by host name or IP address.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 145
 1. In the left navigation menu, click Diagnostics Tools > Ping. The following page appears.

2. Enter the host name or IP address.

3. Click Submit. The details of the ping appear on the page.

4. To return to the Ping Diagnostic page, click Back.

5. To stop a test, click Stop.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 146
Traceroute
On this page, you can use the Traceroute utility to trace a connection.

1. In the left navigation menu, click Diagnostics Tools > Traceroute. The following page appears.

2. Enter the host name or IP address.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 147
 3. Click Submit. The details of the trace appear on the page.

4. To return to the Traceroute Diagnostic page, click Back.

5. To stop a test, click Stop.

Start / Stop DSL

On this page, you can start or stop your DSL connection.

1. In the left navigation menu, click Diagnostics Tools > Start/Stop DSL. The following page appears.

2. To connect to your DSL, click Start. A message appears, with instructions for refreshing the page. When the
connection is ready, the "DSL connection is up" message appears.
3. To stop your connection, click Stop. A message appears, stating that your DSL connection is down.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 148
Management
In this section, you can configure server and system log settings, control access, and configure clients.

Settings
In this section, you can back up the current settings, restore saved settings, or reset the gateway to default settings.

Backup
On this page, you can back up the current settings for your gateway in a file stored on your computer.

1. In the left navigation bar, click Management > Settings. The following page appears.

2. To back up the current running settings:

a. Click Backup Running Settings. The Opening file dialog box appears.
b. Click OK. The file is saved to your default download location and is named "backupsettings.conf".
3. To back up the current default settings:
a. Click Backup Default Settings. The Opening file dialog box appears.
b. Click OK. The file is saved to your default download location and is named
"backupdefaultsettings.conf".

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 149
Update
On this page, you can restore previously backed-up gateway settings.

1. In the left navigation bar, click Management > Settings > Update. The following page appears.

2. To update settings from a file that you saved previously:

a. Click the appropriate Browse button to locate either a customized setting file or the default setting
file (.conf file) on your local system and click Open.
b. Click the associated Update Settings button. The gateway reboots when the update has completed.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 150
Restore Default
On this page, you can restore the gateway to the factory default settings. If you think you might need to reload the current settings,
create a backup (on the Management > Settings > Backup page) before proceeding.

1. In the left navigation menu, click Management > Settings > Restore Default. The following page appears.

2. Click Restore Default Settings. The system returns to the default settings and reboots.

System Log
The System Log page displays a history of error conditions and other events encountered by your gateway. You can configure the
system log and view the security log.

1. In the left navigation bar, click Management > Settings > System Log. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 151
 2. To view the system log details:
a. Click View System Log. The log appears in a separate window.

b. To update the data, click Refresh.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 152
 3. To configure the log settings:
a. Click Configure System Log. The following page appears.

b. Modify the fields as needed, using the information in the table below.
c. Click Apply/Save to save and apply your changes. You are returned to the System Log page.

The fields on this page are defined below.

Action Description
Log Level Select the type of information that you want logged. Options are Emergency, Alert, Critical , Error, Warning,
Notice, Informational , and Debugging. The options are listed in order from least detailed to most detailed. The
default is Debugging.
Display Level Select the level of information that should be displayed. Options are Emergency, Alert, Critical , Error, Warning,
Notice, Informational , and Debugging. The options are listed in order from least detailed to most detailed. The
default is Error. This level is recommended (least verbose) unless you are actively troubleshooting a situation with
a subscriber for which increased detail is required.
Mode Select where log events will be sent. Options are Local, Remote, and Both. Select Remote or Both to send to the
specified IP address and UDP port of a remote syslog server. Select Local or Both to record events in the local
memory of your gateway. The default is Local.
When you select Remote or Both, additional fields appear. Enter the IP address and port number for the remote
syslog server.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 153
Security Log
The security log contains a history of events related to sensitive access to the gateway. Logged events include:
l Password change success / failure
l Authorized login success / failure
l Authorized user logged out
l Security lockout added / removed
l Authorized / unauthorized resource access
l Software update

1. In the left navigation bar, click Management > Security Log. The following page appears.

2. Do any of the following:

l To view the log, click View. The log appears in a separate window.

l To purge the log entries and start fresh, click Reset. A confirming message appears. Click Close.
l To export the log to a local drive, right-click the here link in the last line of the instructions on the page. The
log appears in the browser window. You can save the page or select all of the log text, paste into a text file
and save the file.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 154
SNMP Agent
On this page, you can configure the SNMP (Simple Network Management Protocol) settings to retrieve statistics from the SNMP agent
for the gateway. You can enable or disable the SNMP agent and set parameters such as the read community, system name and trap
manager IP.

1. In the left navigation bar, click Management > SNMP Agent. The following page appears.

2. Modify the fields as needed, using the information provided in the table below.
3. Click Save/Apply to commit your changes.

The fields on this page are defined below.

Field Name Description

SNMP Agent This option is disabled by default. To enable the SNMP agent, click Enable.
Read Community Select whether access to the network community is restricted. Options are public and private. The default is
public.
Set Community Select whether access to the write (set) community is restricted. Options are public and private. The default is
private.
System Name Enter the name of the system.
System Location (Optional) Enter the location of the system.
System Contact (Optional) Enter the contact for the system.
Trap Manager IP (Optional) Enter the IP address where the trap manager is installed.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 155
Management Server
SmartRG gateways support TR-069 based standards for remote management, including STUN server configuration. In this section, you
can configure the gateway with details about the management ACS (Auto Configuration Server) to which this gateway will be linked.

TR-069
The TR-069 client screen contains default connection parameters and generally only needs to be enabled, pointed to the ACS URL,
and any required ACS Username and ACS Password entered. This manual does not cover the setup of your ACS. If you need to modify
the default settings, consult the materials provided by your ACS vendor to determine the appropriate parameters and server
settings.
SmartRG products can accommodate several ACS products, including:
l Calix Consumer ACS
l Cisco Prime Home
l ClearVision
l Device Manager by SmartRG

1. In the left navigation bar, click Management > Management Server. The following page appears.

2. Complete the necessary fields per the instructions from your ACS platform vendor.

Field Name Description

TR-069 Client This option is enabled by default. To disable this feature, click Disable.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 156
 Field Name Description
ACS URL from DHCP Click to enable the gateway to obtain the ACS URL from the DHCP server.
OUI-Serial Select whether to use the MAC address or the device serial number as the identifier. The
default is MAC.
Inform Select whether to disable or enable the inform feature. The default is Enable.
Inform Interval Enter the frequency (in seconds) at which the CPE (gateway) checks in with the ACS to sync
and exchange data. A typical production environment has CPEs informing to the ACS once a
day or every 86,400 seconds. The default is 3600 seconds (1 hour).
ACS URL Enter the URL for the CPE to connect to the ACS using the CPE WAN Management Protocol.
This parameter MUST be in the form of a valid HTTP or HTTPS URL. An HTTPS URL indicates
that the ACS supports SSL. The "host" portion of this URL is used by the CPE for validating the
certificate from the ACS when using certificate-based authentication.
You can include a port specification suffix if your ACS platform requires it, e.g.,
http://customer1.acs.smartrg.com:30005 where 30005 is the port number. The default port
is 30005.
ACS User Name Enter the user name by which this gateway logs in to the ACS.
ACS Password Enter the password to authenticate the above user name.
TR-069 Client Port Enter the port number to be used by the TR-069 client, e.g.,
"http://xxx.xxx.xxx.xxx:30005/" where the xxx values are specific WAN IP octet numbers.
The default port value is 30005.
WAN Interface used by Select any_WAN, LAN, Loopback or any configured connection to identify how this gateway
TR-069 client will connect to the ACS.
Display SOAP messages Select whether to disable or enable the display of SOAP messages on the console. The
on serial console default is Disable.

3. (Optional) To configure the modem client Connection Request mechanism used by your ACS for communication with
subscriber gateways, click Connection Request Authentication. Additional fields appear.
Note: Consult with your ACS vendor for any specific connection request requirement impacted by the following
settings.

Field Name Description

Connection Request Enter the user name by which this gateway authenticates the ACS. For example,
Username many ACS platforms use “admin” or “tr069”.
Connection Request Password Enter the password by which this gateway will authenticate to the ACS.
Connection Request Port Enter the port number assigned for connection requests. The default is 30005.
Connection Request URL This URL is set automatically and cannot be changed. It includes the port number,
e.g., http://10.101.40.115:30005/.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 157
 4. To force the gateway to attempt to sync with the ACS, click the GetRPCMethods button. This will assist you in
verifying the TR-069 parameters entered above.
5. Click Apply/Save to commit your changes.

STUN Config
STUN stands for “Simple Traversal of UDP through NATs”. STUN enables a device to find out its public IP address and the type of NAT
service it is sitting behind.
STUN is most commonly used with older modems under ACS management connected via a NAT gateway. NAT accommodates a LAN-
side device that has been allocated a Private IP address such as a CPE device on a private network behind an ONT. In this instance,
the regular CWMP Connection Request mechanism to talk to the modem gateway cannot be used to initiate a session with that ACS.
A STUN server receives STUN requests and sends STUN responses. STUN servers are generally attached to the public Internet.

On this page, when a STUN server is present within the infrastructure of the Service Provider, you can configure this gateway with
the connectivity specifics for that server.

1. In the left navigation bar, click Management > Management Server > STUN Config. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 158
 2. To view the required STUN settings, click STUN Server Support. Additional fields appear.

3. Modify the fields using the information provided in the following table.
4. Click Save/Apply to commit your changes.

Field Name Description

STUN Server Address Enter the physical STUN server’s assigned network address. An invalid address will produce an immediate
on-page error message from the gateway. You can enter a maximum of 256 characters
An ACS server may also have STUN functionality running on the same physical box. Consult your ACS
vendor for implementation options and also TR-069 protocol documentation, if necessary.
STUN Server Port Enter the port number associated with your STUN server infrastructure. Options are 0 - 64435. The
default is 3478.
STUN Server User Name Enter the username by which the gateway accesses the STUN infrastructure. Maximum length is 256
characters. Special characters are accepted.
STUN Server Password Enter the password by which the modem authenticates the above username to the STUN infrastructure.
Maximum length is 256 characters. Special characters are accepted. The value will be hidden.
STUN Server Maximum Enter the maximum time( in seconds) that the keepalive function should be active. Options are 0-
Keep Alive Period * Unlimited. The default is -1 (no maximum limit).
STUN Server Minimum Enter the minimum time( in seconds) that the keepalive function should be active. Options are 0-
Keep Alive Period * Unlimited. The default is 0 seconds.

* This mechanism is used for refreshing NAT bindings with using Restricted Cone NAT or Port Restricted Cone NAT. A device’s
internal address / port mappings (which the STUN protocol can use) can have keep alive values attributed. These minimum and
maximum keep alive times define the minimum time to retain the mapping information that STUN has discovered, and the maximum
time to retain that information, before refreshing it through forced re-discovery.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 159
With these NAT schemes, the initial network address translation may not be used after a specified elapsed time. Internal mapping is
dropped. The gateway then assigns a different address mapping. This mechanism allows for coordinated refresh on the bindings for
mappings used by the STUN protocol. For further information, review STUN-related RFCs.
Selecting appropriate values for these two fields is influenced by a various environmental factors including device types deployed,
services employed and NAT configuration options enabled within the topology.

XMPP Connection
On this page, you can configure a connection between the gateway and an XMPP server.

1. In the left navigation bar, click Management > XMPP Connection. The following page appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 160
 2. To add a connection, click Add. The following page appears.

3. In the XMPP Connection field, select whether to use TLS and then click Enable.
4. Modify the fields as needed, using the information provided in the table below.

Field Description
Username Enter the username for accessing the XMPP server.
Password Enter the password for accessing the XMPP server.
Domain (Optional) Enter the domain for this connection.
Resource (Optional) Enter a descriptive name for this connection.
XMPP Server Address Enter the IP address for the server.
XMPP Server Port Enter the port for the IP address entered above.

5. Click Apply/Save to save and apply the settings.

6. To remove a connection, click the Remove checkbox to the right of the entry and then click the Remove button.

Internet Time
On this page, you can configure the gateway to synchronize its time with the Internet time servers. This feature is enabled by
default.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 161
 1. In the left navigation bar, click Management > Internet Time. The following page appears.

2. Click Automatically synchronzie with Internet time servers. Additional fields appear.
3. Select the desired time servers.
4. Select the Time zone offset.
5. (Optional) Click Enable Daylight Savings Time.
6. Click Apply/Save to save and apply the settings.
7. To disable this feature, click the Automatically synchronize with Internet time servers check box to clear it and
then click Apply/Save to save your changes.

Access Control
In this section, you can manage user passwords and the services that are available for users.
The following user names are assigned specific rights:
l "admin" has unrestricted access
l "support" has general access rights plus additional rights to perform maintenance tasks and run diagnostics.
l "user" can view settings and statistics and update the firmware.

Passwords
On this page, you can modify the username and password of your users.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 162
 1. In the left navigation bar, click Management > Access Control. The following page appears.

2. Enter the user name in the User Name field.

3. Enter the current password in the Old Password field.
4. Enter the new password in the New Password and Confirm Password fields. Passwords cannot contain spaces.
5. Click Apply/Save to implement your changes.

Access List
On this page, you can create list of IP addresses that are allowed to access local management services (defined in the Services
Control list). When Access Control mode is disabled, IP addresses for incoming packets are not validated.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 163
 1. In the left navigation bar, click Management > Access Control > Access List. The following page appears.

2. To enable the listed IP addresses to access local management services, in the Access Control Mode field, click
Enable.
3. To add an access list:
a. Click Add. The following page appears.

b. Enter the IP address and mask of the station allowed to access local management services.
c. Click Apply/Save. You are returned to the Access List page.
4. To remove a connection, click the Remove checkbox to the right of the entry and then click the Remove button. If
you remove the only entry, Access Control Mode is set to Disable.
5. Click Apply/Save to save and apply the settings.

Services Control
On this page, you can enable or disable the different types of services that your gateway can access.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 164
 1. In the left navigation bar, click Management > Access Control > Services Control. The following page appears.

2. Select or clear the enable checkbox next to each service and interface that you want to change.
3. (Optional) In the WAN Port Number field, modify the port numbers for the services.
4. Click Apply/Save to save and apply the settings.

User Profile
On this page, you can enable or disable access to different features for each user profile defined for your gateway.

1. In the left navigation bar, click Management > Access Control > User Profile. The following page appears.
2. Select or clear the enable checkbox next to each feature to configure access for the selected user profile.
3. Click Apply/Save to save and apply the settings.

Logout Timer
On this page, you can define the maximum time that a session can remain open before the gateway logs out.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 165
 1. In the left navigation bar, click Management > Access Control > Logout Timer. The following page appears.

2. In the Logout Timer Period field, type the number of minutes after which a session will be ended. Options are 0 - 60
minutes. The default is 15 minutes. To disable this feature, enter a zero (0) in the field.

Update Software
On this page, you can update the firmware of your gateway. Software updates for SmartRG product are available for download by
direct customers of SmartRG via the SmartRG Customer Portal.
Note: Make sure that you have downloaded the correct software file as instructed by your ISP.

1. In the left navigation bar, click Management > Update Software. The following screen appears.

2. Click Browse to locate and select the correct software file.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 166
 3. Click Update Software.
Note: When software update is in progress, do not shut down the gateway. After the software update completes, the
gateway automatically reboots.

Reboot
On this page, you can reboot your gateway without needing physical access to the unit.

1. In the left navigation, click Management > Reboot. The following page appears.

2. Click Reboot. The gateway reboots and, after a few minutes, the Login dialog box appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 167
Logout
1. To log out of your gateway, click Logout in the left navigation menu. The Logout page appears.

2. Click the Logout button. A success message appears.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 168
Appendix: FCC Statements
FCC Interference Statement
This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two
conditions:
l This device may not cause harmful interference.
l This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and receiver.

l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
l Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numrique de la classe B est conforme à la norme NMB-003 du Canada.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.

l This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
l This equipment should be installed an operated with a minimum distance of 20cm between the radiator and your body.
l This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.

FCC - PART 68
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom case of this equipment is a label
that contains, among other information, a product identifier in the format US: VW7DL01BSR616A.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 169
This equipment uses the following USOC jacks: RJ-11/RJ45/USB/Power Jacks.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for details.

Ringer Equivalency Number Statement

REN=0.1
Notice: The Ringer Equivalency Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed
to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service
may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised
of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If
this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact SmartRG,Inc. If the equipment is causing harm to
the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation
commission for information.

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this device does not disable your alarm
equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

IC CS-03 statement
This product meets the applicable Industry Canada technical specifications. / Le présent matériel est conforme aux specifications techniques
applicables d’Industrie Canada

The Ringer Equivalence Number (REN) is an indication of the maximum number of devices allowed to be connected to a telephone interface. The
termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not
exceed five. / L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés à une
interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la
somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas cinq.

Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can
obtain Canadian information on RF exposure and compliance.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 170
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf,
utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and
operated with a minimum distance of 20 centimeters between the radiator and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être
installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.

This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate
with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I)
a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et
l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

5GHz
5150-5250 MHz band is restricted to indoor operations only.

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 171
Revision History
Revision Date LAN ports
1.1 Apr 2018 Updated to match release 2.6.1.5.
1.0 Mar 2018 Updated to match release 2.6.1

SMARTRG INC. PROPRIETARY AND CONFIDENTIAL. ALL RIGHTS RESERVED. COPYRIGHT © 2018 172