www.DataSheet.co.

kr

Approval

To :
Date : 2005-02-17

SAMSUNG TFT-LCD

MODEL NO. : LTM170E8-L01

Approved by :

Any Modification of Spec is not allowed without SEC's permission.

Senior Manager : Y.D. Jo

PREPARED BY : LCD Business Technical Customer Service Team

Samsung Electronics Co . , LTD.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 2 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
Contents

Revision History -------------------------- (3)

General Description -------------------------- (4)
1. Absolute Maximum Ratings -------------------------- (5)
1.1 Absolute ratings of environment
1.2 Electrical Absolute Ratings
2. Optical Characteristics -------------------------- (7)
3. Electrical Characteristics -------------------------- (12)
3.1 TFT LCD Module
3.2 Back-light Unit
4. Block Diagram -------------------------- (16)
4.1 TFT LCD Module
4.2 Back-light Unit
5. Input Terminal Pin Assignment -------------------------- (17)
5.1 Input Signal & Power
5.2 LVDS Interface (1)
5.3 LVDS Interface (2)
5.4 Back-light Unit
5.5 Input Signals, Basic Display Colors and Gray Scale of Each Color
6. Interface Timing -------------------------- (24)
6.1 Timing Parameters (DE only mode)
6.2 Timing Diagrams of Interface Signal (DE only mode)
6.3 Power ON/OFF Sequence
6.4 VDD Power Dip Condition
6.5 LVDS Input Characteristics
7. Outline Dimension -------------------------- (30)
8. Reliability Test -------------------------- (32)
9. Packing -------------------------- (33)
10. Marking & Others -------------------------- (34)
11. Inspection Criteria -------------------------- (36)
12. General Precaution -------------------------- (37)
12.1 Handling
12.2 Storage
12.3 Operation
12.4 Others

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 2 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

* Revision History Approval

Date Rev. No Page Summary
Feb. 17, E00 All Approval specification of LTM170E8-L01 model was issued first.
2005

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 3 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

General Description Approval

* Description

LTM170E8-L01 is a color active matrix TFT (Thin Film Transistor) liquid crystal display
(LCD) that uses amorphous silicon TFTs as switching devices. This model is composed of
a TFT LCD panel, a driver circuit and a back-light system. The resolution of a 17.0" contains
1280 x 1024 pixels and can display up to 16.7 millions colors with wide viewing angles of
89° in all directions. (Vertical viewing angle : 178° , Horizontal viewing angle : 178° )

* Features

- High contrast ratio, high aperture structure

- PVA(Plus Viewing Angle) mode
- Wide viewing angle & High speed response
- SXGA(1280 x 1024 pixels) resolution
- Low power consumption
- 2 dual CCFTs(Cold Cathode Fluorescent Tube)
- DE (Data Enable) mode
- LVDS (Low Voltage Differential Signaling) interface (2pixel/clock)
- Compact Size Design
- Pb-free configuration

* Applications

Workstation & desktop monitors

Display terminals for AV application products
Monitors for industrial machine
* If the module is used to other applications besides the above, please contact SEC
in advance.

* General information
Items Specification Unit Note
Display area 337.92(H) x 270.336(V) mm
Driver element a-Si TFT active matrix
Display colors 16.7M colors
Number of pixels 1280 x 1024 pixel
Pixel arrangement RGB vertical stripe
Pixel pitch 0.264(H) x 0.264(W) mm
Display mode Normally Black
Surface treatment Haze 44% , Hard-coating (3H)

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 4 / 38

Datasheet pdf - http://www.DataSheet4U.net/
w w w . D a t a S h e e t . c o . k r

Approval
* Mechanical information
Item Min. Typ. Max. Note
Horizontal(H) 354.5 354.9 355.4 mm
Module
Vertical(V) 289.8 290.3 290.8 mm
size
Depth(D) - - 13.3 mm
Weight - - 1,700 g

1. Absolute Maximum Ratings

1.1 Absolute ratings of environment

Item Symbol Min. Max. Unit Note
Storage temperature TSTG -20 65 ℃ (1)
Operating temperature
TOPR 0 50 ℃ (1)
(Glass surface temperature)
Shock ( non - operating ) Snop - 50 G (2),(4)
Vibration ( non - operating ) Vnop - 1.5 G (3),(4)

Note (1) Temperature and relative humidity range are shown in the figure below.
90 % RH Max. ( 40 ° C ≥ Ta )
Maximum wet-bulb temperature at 39 ° C or less. (Ta > 40 ° C) No condensation.
(2) 11ms, sine wave, one time for ±X, ±Y, ±Z axis
(3) 10-300 Hz, Sweep rate 10min, 30min for X,Y,Z axis
(4) At vibration and shock test, the fixture which holds the module to be tested
has to be hard and rigid enough so that the module would not be twisted or
bent by the fixture.

Relative Humidity ( %RH)

100
90
(40℃, 90%)
80

60
Operating Range (50℃, 50.4%)
40

(65℃, 27.7%)
20
(-20℃, 5%) 5
Storage Range
0
-40 -20 0 20 40 60 80

Temperature (OC)

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 5 / 38

D a t a s h e e t p d f - h t t p : / / w w w . D a t a S h e e t
www.DataSheet.co.kr

Approval
1.2 ELECTRICAL ABSOLUTE RATINGS
(1) TFT LCD Module (Vss = GND = 0 V)
Item Symbol Min. Max. Unit Note
Power Supply Voltage VDD Vss-0.5 6.5 V (1)

Note (1) Within Ta ( 25 ± 2 ° C)

(2) BACK-LIGHT UNIT (Ta = 25 ± 2° C)

Item Symbol Min. Max. Unit. Note

Lamp Current IL 3.0 7.0 mArms (1),(2)
Lamp Frequency fL 40 80 kHz (1)

Note (1) Permanent damage to the device may occur if maximum values are exceeded.
Functional operation should be restricted to the conditions described
under Normal Operating Conditions.
(2) Specified values are for a single lamp.
(Refer to the Note (1) in the page 14 for further information).

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 6 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

2. Optical Characteristics Approval

The following items are measured under stable conditions. The optical characteristics should be
measured in a dark room or equivalent state with the methods shown in Note (1).

Measuring equipment : TOPCON BM-5A, BM-7, PHOTO RESEARCH PR650

Eldim EZ-Contrast
(Inverter Freq. : 50kHz) * Ta = 25 ± 2° C, VDD=5V, fv= 60Hz, fDCLK=54MHz, IL = 6.5mArms

Item Symbol Condition Min. Typ. Max. Unit Note

Contrast Ratio (3)
C/R 800 1500 -
(Center of screen) BM-5A
Response Rising Tr - 15 20 (5)
msec
Time Falling Tf - 10 15 BM-7
Luminance of White (6)
YL 240 280 - cd/m2
(Center of screen) BM-5A
Rx 0.610 0.640 0.670
Red
Ry 0.300 0.330 0.360
Gx 0.270 0.300 0.330
Color Green
Gy Normal 0.570 0.600 0.630
Chromaticity
Bx φ= 0 0.120 0.150 0.180
(CIE 1931) Blue
By θ = 0 0.030 0.060 0.090
Wx 0.283 0.313 0.343
White
Wy Viewing 0.299 0.329 0.359 (7)
Ru' Angle - 0.451 - PR650
Red
Rv' - 0.523 -
Gu' - 0.125 -
Color Green
Chromaticity Gv' - 0.563 -
(CIE 1976) Bu' - 0.175 -
Blue
Bv' - 0.158 -
Wu' - 0.198 -
White
Wv' - 0.468 -
Color
(9)
Grayscale White ∆u'v' - - 0.02
PR650
Linearity
θ L 80 89 -
Hor.
θ R 80 89 -
CR≥ 10
φH 80 89 -
Ver.
Viewing φL 80 89 - (8)
Degrees
Angle θ L - 75 - BM-5A
Hor.
θ R CR≥ 100 - 75 -
φH - 65 -
Ver.
φL - 65 -
Brightness Uniformity (4)
Buni - - 25 %
(9 Points) BM-5A

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 7 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
Note (1) Test Equipment Setup

The measurement should be executed in a stable, windless and dark room between
30min and 40min after lighting the back-light at the given temperature for stabilization
of the back-light. This should be measured in the center of screen.

Single lamp current : 6.5mA (Refer to the note(1) in the page 14 for more information.)
Environment condition : Ta = 25 ± 2 ° C

Photodetector

Photodetector Field

BM-5A 2° Field
BM-7 2°
PR650 1°
BM-5A : 40㎝
BM-7 : 50㎝
PR650 : 50㎝
TFT - LCD Module

LCD Panel

The center of the screen

Optical Measuring Equipment Setup

Note (2) Definition of test point

128 640 1152
Active AREA
9 8 7 102

6 5 4 512

3 2 1 922 : test point

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 8 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
Note (3) Definition of Contrast Ratio (C/R)
: Ratio of gray max (Gmax) & gray min (Gmin) at the center point⑤ of the panel
G max
CR =
G min
Gmax : Luminance with all pixels white
Gmin : Luminance with all pixels black

Note (4) Definition of 9 points brightness uniformity

( B max − B min)
Buni = 100∗
B max

Bmax : Maximum brightness

Bmin : Minimum brightness

Note (5) Definition of Response time : Sum of Tr, Tf

Display data Black(TFT OFF) White(TFT ON) Black(TFT OFF)

TR TF
100%
Optical
90%
Response

10%
0%
Time

Note (6) Definition of Luminance of White : Luminance of white at center point⑤

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 9 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
Note (7) Definition of Color Chromaticity (CIE 1931, CIE 1976)
Color coordinate of Red, Green, Blue & White at center point⑤

Note (8) Definition of Viewing Angle : Viewing angle range (CR ≥10, CR ≥100)

N o rm a l L in e
φ = 0o, θ = 0o
θL
θR
φL φH 1 2 O ’c lo c k
θ L = 9 0o x y d ire c tio n
φ H = 9 0o

6 O ’c lo c k y ’ x’
d ire c tio n
θR = 9 0o
φ L= 9 0o

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 10 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Note (9) Color Grayscale Linearity

Approval
① test image : 100% full white pattern with a test pattern as below
② test pattern : Squares, 40mm by 40mm in size, filled with 255, 225, 195, 165, 135
and 105 grays steps should be arranged at the center⑤ of the screen.
40mm

40mm

③ test method
. 1st gray step : move a square of 255 gray level should be moved
into the center of the screen and measure luminance and
u' and v' coordinates.
. next gray step : move a 225 gray square into the center and measure both
luminance and coordinates, too.
. Then, repeat the same procedure for gray steps 195, 165- 135 and 105.
④ test evaluation

where A, B : 2 gray levels found to have the largest color differences

between them
i.e. get the largest Δu' and Δv' of each 6 pairs of u' and v' and
calculate the Δu'v'.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 11 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

3. Electrical Characteristics Approval

3.1 TFT LCD MODULE
Ta = 25° C
Item Symbol Min. Typ. Max. Unit Note
Voltage of Power Supply VDD 4.5 5.0 5.5 V (1)
Interface type LVDS DS90C383/385/387 DS90C386 Pair
Current of (a) Black - 700 - mA
Power (b) White IDD - 800 - mA (2),(3)
Supply (c) Dot - 1000 1250 mA
Vsync Frequency fV 55 60 76 Hz
Hsync Frequency fH 56.7 64 81.1 kHz
Main Frequency fDCLK 38.1 54 68.4 MHz
Rush Current IRUSH - - 4.0 A (4)

Note (1) The connector for display data & timing signal should be connected.(Vss=0V)
(2) fV=75Hz, fDCLK = 67.5MHz, VDD = 5.0V, DC Current.
(3) Power dissipation check pattern(LCD Module only)

a) Black Pattern b) White Pattern

c) Dot Pattern

RGBRGB RGBR

RGBRGB RGB RGB RGBR

B RGBRGBRGB RGB RGBRGR

GBRGBRGB RGBRGBRGB RG

RGBRGBRGB RGB RGBR

RGB RGBRGBRG

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 12 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
(4) Measurement Conditions

5V M1
2SK1059
VDD ( LCD INPUT)
FUSE
R1 C1
47K 1uF

R2
CONTROL SIGNAL
M2
(HIGH to LOW)
1K 2SK1399

12V
R3 C2

C3 47K
10000pF
1uF

Control Signal : High(+5V) → Low(Ground)

All Signal lines to panel, except for power 5V : Ground
The rising time of supplied voltage is controlled to 470us by R3 and C2 value.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 13 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
3.2 BACK-LIGHT UNIT
The back-light system is an edge - lighting type with 2 dual CCFTs ( Cold Cathode
Fluorescent Tube ) The characteristics of two dual lamps are shown in the following tables.
Ta=25 ± 2°C
Item Symbol Min. Typ. Max. Unit Note
Lamp Current IL 3.0 6.5 7.0 mArms (1)
Lamp Voltage VL - 630 - Vrms
Lamp Frequency fL 40 - 60 kHz (2)
Operating Life Time Hr 50,000 - - Hour (3)
asymmetry
Wasy - - 10 %
inverter rate
(6)
waveform distortion
Wdis - - √2 ±10 %
rate
0℃ : 1,580
Startup Voltage Vs - - Vrms (4)
25℃ : 1,210

Note) The wave form of the inverter output voltage must be area symmetric and the design
of the inverter must have specifications for the modularized lamp.
The performance of the back-light, for example life time or brightness, is much influenced by the
characteristics of the DC-AC inverter for the lamp. So all the parameters of an inverter should be
carefully designed so as not to produce too much leakage current from high-voltage output of the
inverter. When you design or order the inverter, please make sure that a poor lighting caused by the
mismatch of the back-light and the inverter(poor lighting, flicker, etc.) never occur. When you confirm
it, the module should be operated in the same condition as it is installed in your instrument.

Note (1) Lamp current is measured with current meter for high frequency as shown below.
Refer to the block diagram of the back-light unit in the next page for more information.
Specified values are for a single lamp.
Hot (Pink)
Cold (White)
Hot (Blue)
Cold (Black)
A Inverter
LCD Module
(SK1700A)
Hot (Pink)
Cold (White)
Hot (Blue)
Cold (Black)

(2) Lamp frequency which may produce interference with horizontal synchronous frequency may
cause line flow on the display. Therefore lamp frequency should be detached from the horizontal
synchronous frequency and its harmonics as far as possible in order to avoid interference.
(3) Life time (Hr) of a lamp is defined as the time in which it continues to operate under the
condition of Ta = 25±2°C and IL = 6.5mArms for a lamp until the brightness becomes 50%
or lower than its original value. Operating condition is lamp unit itself, not module assembly at
operating current 6.5mA.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 14 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
(4) If an inverter has shutdown function, it should keep its output for over 1 second even if the
lamp connector is open. Otherwise the lamps may not be turned on.
(5) Because the inverter uses high voltage, please disconnect it from the power before
assembling or disassembling.
(6) The output of the inverter must have symmetrical(negative and positive) voltage waveform
and current waveform.
Please do not use the inverter which has unsymmetrical voltage and current and spike wave.
Designing a system inverter intended to have better display performance,
power efficiency and lamp reliability, please follow the requirements the below.
They would help increase the lamp lifetime and reduce leakage current.

a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion rate of the waveform should be within √2 ±10%.
* Inverter output waveform had better be more similar to ideal sine wave.

* Asymmetry rate:
Ip | I p – I –p | / Irms x 100%

* Distortion rate
I -p
I p (or I –p) / Irms

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 15 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

4. Block Diagram Approval

4.1 TFT LCD MODULE

LVDS Odd Data Driver(Column)

signals
LVDS Timing
DS90C
Controller
INPUT CONNECTOR

386
Even

Gate
TFT-LCD
Driver
(Row)
DC Power
supply LCD
Drive
Analog
Circuit

4.2 BACK-LIGHT UNIT

Connector : YEONHO 35001HS-02L or equivalent

LAMP(CCFL) HOT(PINK)
1
COLD(WHITE)
2

LAMP(CCFL) 3
HOT(BLUE)
4
COLD(BLACK)

HOT(PINK)
LAMP(CCFL) 1
COLD(WHITE)
2

LAMP(CCFL) 3
HOT(BLUE)
4
COLD(BLACK)

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 16 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

5. Input Terminal Pin Assignment Approval

5.1. Input Signal & Power ( Connector : Uju IN-30-OB100 or equivalent )

PIN NO SYMBOL FUNCTION

1 RXO0- Negative Transmission Data of Pixel 0 (ODD data)
2 RXO0+ Positive Transmission Data of Pixel 0 (ODD data)
3 RXO1- Negative Transmission Data of Pixel 1 (ODD data)
4 RXO1+ Positive Transmission Data of Pixel 1 (ODD data)
5 RXO2- Negative Transmission Data of Pixel 2 (ODD data)
6 RXO2+ Positive Transmission Data of Pixel 2 (ODD data)
7 GND Power Ground
8 RXOC- Negative Sampling Clock (ODD data)
9 RXOC+ Positive Sampling Clock (ODD data)
10 RXO3- Negative Transmission Data of Pixel 3 (ODD data)
11 RXO3+ Positive Transmission Data of Pixel 3 (ODD data)
12 RXE0- Negative Transmission Data of Pixel 0 (EVEN data)
13 RXE0+ Positive Transmission Data of Pixel 0 (EVEN data)
14 GND Power Ground
15 RXE1- Negative Transmission Data of Pixel 1 (EVEN data)
16 RXE1+ Positive Transmission Data of Pixel 1 (EVEN data)
17 GND Power Ground
18 RXE2- Negative Transmission Data of Pixel 2 (EVEN data)
19 RXE2+ Positive Transmission Data of Pixel 2 (EVEN data)
20 RXEC- Negative Sampling Clock (EVEN data)
21 RXEC+ Positive Sampling Clock (EVEN data)
22 RXE3- Negative Transmission Data of Pixel 3 (EVEN data)
23 RXE3+ Positive Transmission Data of Pixel 3 (EVEN data)
24 GND Power Ground
25 *CE For LCD internal use only. Do not connect
26 *CTL For LCD internal use only. Do not connect
27 NC No connection.
28
29 VDD Power Supply : +5V
30

Note ) Refer to page 30 for the 1st pin of interface connector marked with ▼.
* If the system already uses the 25, 26pins, it should keep under GND level.
The voltage applied to those pins should not exceed -200mV.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 17 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
5.2 LVDS Interface(1)

5.2.1 Odd pixel data (1st pixel data)

1st LVDS Transmitter ( DS90C383, DS90C385 ) Signal Interface

To LTM170E8
Device Input Pin Device Input Signal Output
Interface ( CN101 )
Signal
No Symbol Symbol Function Terminal Symbol
51 TXIN0 RO0 Red Odd Pixel Data (LSB)
52 TXIN1 RO1 Red Odd Pixel Data
TXOUT0- No. 1 RXO0-
54 TXIN2 RO2 Red Odd Pixel Data
TXOUT0+ No. 2 RXO0+
55 TXIN3 RO3 Red Odd Pixel Data
56 TXIN4 RO4 Red Odd Pixel Data
TXOUT3- No. 10 RXO3-
2 TXIN5 RO7 Red Odd Pixel Data (MSB)
TXOUT3+ No. 11 RXO3+
3 TXIN6 RO5 Red Odd Pixel Data TXOUT0- No. 1 RXO0-
4 TXIN7 GO0 Green Odd Pixel Data (LSB) TXOUT0+ No. 2 RXO0+

6 TXIN8 GO1 Green Odd Pixel Data TXOUT1- No. 3 RXO1-

7 TXIN9 GO2 Green Odd Pixel Data TXOUT1+ No. 4 RXO1+

8 TXIN10 GO6 Green Odd Pixel Data TXOUT3- No. 10 RXO3-

10 TXIN11 GO7 Green Odd Pixel Data (MSB) TXOUT3+ No. 11 RXO3+

11 TXIN12 GO3 Green Odd Pixel Data

12 TXIN13 GO4 Green Odd Pixel Data TXOUT1- No. 3 RXO1-
14 TXIN14 GO5 Green Odd Pixel Data TXOUT1+ No. 4 RXO1+

15 TXIN15 BO0 Blue Odd Pixel Data (LSB)

16 TXIN16 BO6 Blue Odd Pixel Data TXOUT3- No. 10 RXO3-
18 TXIN17 BO7 Blue Odd Pixel Data (MSB) TXOUT3+ No. 11 RXO3+
TXOUT1- No. 3 RXO1-
19 TXIN18 BO1 Blue Odd Pixel Data
TXOUT1+ No. 4 RXO1+
20 TXIN19 BO2 Blue Odd Pixel Data
22 TXIN20 BO3 Blue Odd Pixel Data TXOUT2- No. 5 RXO2-
23 TXIN21 BO4 Blue Odd Pixel Data TXOUT2+ No. 6 RXO2+

24 TXIN22 BO5 Blue Odd Pixel Data

TXOUT3- No. 10 RXO3-
50 TXIN27 RO6 Red Odd Pixel Data
TXOUT3+ No. 11 RXO3+

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 18 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
5.2.2 Even pixel data (2nd pixel data)
2nd LVDS Transmitter ( DS90C383, DS90C385 ) Signal Interface

To LTM170E8
Device Input Pin Device Input Signal Output
Interface ( CN101 )
Signal
No Symbol Symbol Function Terminal Symbol
51 TXIN0 RE0 Red Even Pixel Data (LSB)
52 TXIN1 RE1 Red Even Pixel Data
TXOUT0- No. 12 RXE0-
54 TXIN2 RE2 Red Even Pixel Data
TXOUT0+ No. 13 RXE0+
55 TXIN3 RE3 Red Even Pixel Data
56 TXIN4 RE4 Red Even Pixel Data
TXOUT3- No. 22 RXE3-
2 TXIN5 RE7 Red Even Pixel Data (MSB)
TXOUT3+ No. 23 RXE3+
3 TXIN6 RE5 Red Even Pixel Data TXOUT0- No. 12 RXE0-
4 TXIN7 GE0 Green Even Pixel Data (LSB) TXOUT0+ No. 13 RXE0+

6 TXIN8 GE1 Green Even Pixel Data TXOUT1- No. 15 RXE1-

7 TXIN9 GE2 Green Even Pixel Data TXOUT1+ No. 16 RXE1+

8 TXIN10 GE6 Green Even Pixel Data TXOUT3- No. 22 RXE3-

10 TXIN11 GE7 Green Even Pixel Data (MSB) TXOUT3+ No. 23 RXE3+

11 TXIN12 GE3 Green Even Pixel Data

12 TXIN13 GE4 Green Even Pixel Data TXOUT1- No. 15 RXE1-
14 TXIN14 GE5 Green Even Pixel Data TXOUT1+ No. 16 RXE1+

15 TXIN15 BE0 Blue Even Pixel Data (LSB)

16 TXIN16 BE6 Blue Even Pixel Data TXOUT3- No. 22 RXE3-
18 TXIN17 BE7 Blue Even Pixel Data (MSB) TXOUT3+ No. 23 RXE3+
TXOUT1- No. 15 RXE1-
19 TXIN18 BE1 Blue Even Pixel Data
TXOUT1+ No. 16 RXE1+
20 TXIN19 BE2 Blue Even Pixel Data
22 TXIN20 BE3 Blue Even Pixel Data TXOUT2- No. 18 RXE2-
23 TXIN21 BE4 Blue Even Pixel Data TXOUT2+ No. 19 RXE2+

24 TXIN22 BE5 Blue Even Pixel Data

TXOUT3- No. 22 RXE3-
50 TXIN27 RE6 Red Even Pixel Data
TXOUT3+ No. 23 RXE3+

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 19 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
5.3 LVDS Interface (2)

5.3.1 Odd pixel data (1st pixel data)

LVDS Transmitter ( DS90C387 ) Signal Interface

To LTM170E8
Device Input Pin Device Input Signal Output
Interface ( CN101 )
Signal
No Symbol Symbol Function Terminal Symbol
10 R10 RO0 Red Odd Pixel Data (LSB)
9 R11 RO1 Red Odd Pixel Data
A0M No. 1 RXO0-
8 R12 RO2 Red Odd Pixel Data
A0P No. 2 RXO0+
7 R13 RO3 Red Odd Pixel Data
6 R14 RO4 Red Odd Pixel Data
A3M No. 10 RXO3-
3 R17 RO7 Red Odd Pixel Data (MSB)
A3P No. 11 RXO3+
5 R15 RO5 Red Odd Pixel Data A0M No. 1 RXO0-
2 G10 GO0 Green Odd Pixel Data (LSB) A0P No. 2 RXO0+

1 G11 GO1 Green Odd Pixel Data A1M No. 3 RXO1-

100 G12 GO2 Green Odd Pixel Data A1P No. 4 RXO1+

94 G16 GO6 Green Odd Pixel Data A3M No. 10 RXO3-

93 G17 GO7 Green Odd Pixel Data (MSB) A3P No. 11 RXO3+

99 G13 GO3 Green Odd Pixel Data

96 G14 GO4 Green Odd Pixel Data A1M No. 3 RXO1-
95 G15 GO5 Green Odd Pixel Data A1P No. 4 RXO1+

92 B10 BO0 Blue Odd Pixel Data (LSB)

86 B16 BO6 Blue Odd Pixel Data A3M No. 10 RXO3-
85 B17 BO7 Blue Odd Pixel Data (MSB) A3P No. 11 RXO3+
A1M No. 3 RXO1-
91 B11 BO1 Blue Odd Pixel Data
A1P No. 4 RXO1+
90 B12 BO2 Blue Odd Pixel Data
89 B13 BO3 Blue Odd Pixel Data A2M No. 5 RXO2-
88 B14 BO4 Blue Odd Pixel Data A2P No. 6 RXO2+

87 B15 BO5 Blue Odd Pixel Data

A3M No. 10 RXO3-
4 R16 RO6 Red Odd Pixel Data
A3P No. 11 RXO3+

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 20 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
5.3.2 Even pixel data (2nd pixel data)
LVDS Transmitter ( DS90C387 ) Signal Interface

To LTM170E8
Device Input Pin Device Input Signal Output
Interface ( CN101 )
Signal
No Symbol Symbol Function Terminal Symbol
84 R20 RE0 Red Even Pixel Data (LSB)
81 R21 RE1 Red Even Pixel Data
A4M No. 12 RXE0-
80 R22 RE2 Red Even Pixel Data
A4P No. 13 RXE0+
79 R23 RE3 Red Even Pixel Data
78 R24 RE4 Red Even Pixel Data
A7M No. 22 RXE3-
75 R27 RE7 Red Even Pixel Data (MSB)
A7P No. 23 RXE3+
77 R25 RE5 Red Even Pixel Data A4M No. 12 RXE0-
74 G20 GE0 Green Even Pixel Data (LSB) A4P No. 13 RXE0+

73 G21 GE1 Green Even Pixel Data A5M No. 15 RXE1-

72 G22 GE2 Green Even Pixel Data A5P No. 16 RXE1+

66 G26 GE6 Green Even Pixel Data A7M No. 22 RXE3-

65 G27 GE7 Green Even Pixel Data (MSB) A7P No. 23 RXE3+

71 G23 GE3 Green Even Pixel Data

70 G24 GE4 Green Even Pixel Data A5M No. 15 RXE1-
69 G25 GE5 Green Even Pixel Data A5P No. 16 RXE1+

64 B20 BE0 Blue Even Pixel Data (LSB)

58 B26 BE6 Blue Even Pixel Data A7M No. 22 RXE3-
57 B27 BE7 Blue Even Pixel Data (MSB) A7P No. 23 RXE3+
A5M No. 15 RXE1-
63 B21 BE1 Blue Even Pixel Data
A5P No. 16 RXE1+
62 B22 BE2 Blue Even Pixel Data
61 B23 BE3 Blue Even Pixel Data A6M No. 18 RXE2-
60 B24 BE4 Blue Even Pixel Data A6P No. 19 RXE2+

59 B25 BE5 Blue Even Pixel Data

A7M No. 22 RXE3-
76 R26 RE6 Red Even Pixel Data
A7P No. 23 RXE3+

NOTE)
Must be connected 24th BAL pin with low and 23th DUAL pin with high in DS90C387 LVDS
Transmitter

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 21 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
5.4 BACK-LIGHT UNIT

Pin No. Input Color Function

1 Hot1 Pink High Voltage

2 Cold1 White Ground
Upper
3 Hot2 Blue High Voltage
4 Cold2 Black Ground
1 Hot1 Pink High Voltage
2 Cold1 White Ground
Lower
3 Hot2 Blue High Voltage
4 Cold2 Black Ground

Connector
YEONHO 35001HS-02L or equivalent
Part No.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 22 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
5.5 Input Signals, Basic Display Colors and Gray Scale of Each Color
DATA SIGNAL GRAY
COLOR DISPLAY RED GREEN BLUE SCALE
LEVEL
R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7
BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -

BLUE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -

GREEN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -

BASIC CYAN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
COLOR RED 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -
MAGENTA 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -

YELLOW 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -

WHITE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R0

1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R1
DARK
↑ 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R2
GRAY
: : : : : : : : : : : : : : : : : : : : : : : : R3~
SCALE
: : : : : : : : : : : : : : : : : : : : : : : : R252
OF RED
↓ 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R253
LIGHT
0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R254
RED 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R255

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G0
0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G1
DARK
GRAY ↑ 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G2

SCALE : : : : : : : : : : : : : : : : : : : : : : : : G3~
OF : : : : : : : : : : : : : : : : : : : : : : : : G252
GREEN ↓ 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G253
LIGHT
0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G254

GREEN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G255

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 B1
DARK
GRAY ↑ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 B2

SCALE : : : : : : : : : : : : : : : : : : : : : : : : B3~
OF : : : : : : : : : : : : : : : : : : : : : : : : B252
BLUE ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 B253
LIGHT
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 B254

BLUE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 B255

Note) Definition of Gray :

Rn : Red Gray, Gn : Green Gray, Bn : Blue Gray (n = Gray level)
Input Signal : 0 = Low level voltage, 1 = High level voltage

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 23 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

6. Interface Timing Approval

6.1 Timing Parameters ( DE only mode )

SIGNAL ITEM SYMBOL MIN. TYP. MAX. UNIT NOTE

Frequency 1/TC 38.1 54 68.4 MHz

Clock High Time TCH 4 - - nsec

Low Time TCL 4 - - nsec

(1), (2)
Setup Time TDS 4 - - nsec
Data
Hold Time TDH 4 - - nsec

Data Enable Setup Time TES 4 - - nsec

18.2 16.7 13.1 msec

Cycle Tv
Frame Frequency 1032 1066 1066 lines

Frequency 1/Tv 55 60 76 Hz (3)

Display Period TVD 1024 1024 1024 lines

Vertical Active
Display Term Vertical Blank
TVB 8 - - lines
Period
One Line
Cycle TH 672 - 844 clocks
Scanning Time
Horizontal Active
Display Period THD 640 640 640 clocks
Display Term

Note (1) Test Point : TTL control signal and CLK at LVDS Tx input terminal in system
(2) Internal Vcc = 3.3V
(3) At low Vsync frequency, under 60Hz, flicker level can increase at specific pattern.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 24 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
6.2 Timing diagrams of interface signal ( DE only mode )
TV

TVD TVB

DE

TH

THD

DE

DCLK
TC
DATA
SIGNALS

TC
TCH TCL

DCLK 0.5 VCC

TDS TDH

DISPLAY
0.5 VCC
DATA

TES

DE 0.5 VCC

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 25 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
6.3 Power ON/OFF Sequence

To prevent a latch-up or DC operation of the LCD module, the power on/off sequence
should be as the diagram below.

0.9 VDD 0.9 VDD

Power Supply
VDD 0.1 VDD 0.1 VDD
0V

300㎲≤ T1 ≤ 10msec
0 ≤ T2 ≤ 50 msec T1 T3
0 ≤ T3 ≤ 50 msec T2
1sec ≤ T 4 T4

VALID
Signals
0V

Power On Power Off

Back-light(Recommended) 50% 50%

500 msec ≤ T5
100 msec ≤ T 6

T5 T6

Power ON/OFF Sequence

Note. (1) The supply voltage of the external system for the module input should be the
same as the definition of VDD.
(2) Apply the lamp voltage within the LCD operation range. When the back-light
turns on before the LCD operation or the LCD turns off before the back-light
turns off, the display may momentarily show abnormal screen.
(3) In case of VDD = off level,
please keep the level of input signals low or keep a high impedance.
(4) T4 should be measured after the module has been fully discharged between
power off and on period.
(5) Interface signal should not be kept at high impedance when the power is on.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 26 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

6.4 VDD Power Dip Condition

Approval

VDD

Vcc

Td

GND

4.5V ≤ VDD ≤5.5V

if VDD(typ) x 20% ≤ Vcc ≤ VDD(typ) x 10%,
then, 0<Td≤20msec

NOTE
(1) The above conditions are for the glitch of the input voltage.
(2) For stable operation of an LCD module power, please follow them.
i.e., if typ VDD x 20% ≤ Vcc ≤ typ VDD x 10%,
then Td should be less than 20ms.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 27 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

6.5 LVDS Input Characteristics

Approval
6.5.1 LVDS Receiver input
Symbol Parameter Conditions Min Typ Max unit Note

VTH LVDS input high threshold +100 mV

VCMLVDS = 1.25V
VTL LVDS input low threshold -100 mV
LVDS input common mode
VCMLVDS 1.125 1.25 1.375 V
voltage
VIN=2.4V/0V
IIN Input current -10 +10 ㎂
VDD=3.6V
skew between
tskew -200 0 200 psec (1)
LVDS clock & LVDS data

Note (1) LVDS skew

LVDS Clk Vdiff = 0V Vdiff = 0V Differential

LVDS data
Differential
RX+/-
tskew1

where tskew : skew between LVDS clock & LVDS data,

T : 1 period time of LVDS clock
cf) (-/+) of 200psec means LVDS data goes before or after LVDS clock.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 28 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
6.5.2 RSDS Output
Symbol Parameter Conditions Min Typ Max unit
Output differential
VOHDIF 150 170 200 mV
high voltage
Output differential RL = 100Ω
VOLDIF -200 170 150 mV
low voltage PII = 13KΩ
RSDS output
VCM 1.0 1.2 1.4 V
common voltage
RSDS output
RL 50 100 110 Ω
load impedance

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 29 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

7. Outline Dimension Approval

[ Refer to the next page ]

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 30 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

8. Reliability Test Approval

Test Items Conditions Time/Cycle Sample
HTOL* 50°C , Bias 500 hrs 12
LTOL* 0°C , Bias 500 hrs 5
THB** 40°C / 95% , Bias 500 hrs 5
HTS*** 70°C , No Bias 500 hrs 5
LTS*** -30°C , No Bias 500 hrs 5
Thermal Cycle -20°C/30min ~ +60°C/30min , No bias 100 cycle 5
Box Drop 1 angle , 3 edge , 6 side , 66 cm 5
Shock 50G , 11msec
1 time/axis 3
(Non-operating) Sine wave , ± x/y/z axis
Vibration 1.5G , 10~300 Hz
30min/axis 3
(Non-operating) ±x/y/z axis , sweep rate : 10 min
contact : 150pF, 330Ω, 100points, once/point ± 8kV 3
Operating
ESD Air(non-contact) : 150pF, 330Ω, 100points, once/point ± 15kV 3
Non-
CDM : 150pF , 330Ω, 9points, 3times/point ± 10kV 3
operating

[ Result Evaluation Criteria]

Under the display quality test conditions with normal operation state, these should
be no change which may affect practical display functions.

* HTOL/ LTOL : High/Low Temperature Operating Life,

** THB : Temperature Humidity Bias
*** HTS/LTS : High/Low Temperature Storage

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 32 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

9. PACKING Approval
9.1 CARTON (Internal Package)
(1) Packing Form
Corrugated fiberboard box and EPS cushion as shock absorber
(2) Packing Method
a) Without Inverter

Both sided
tape

SHIELDING-BAG

CUSHION-PAD

PANEL-PROTECTOR

TAPE-PAPER(4 Point)

PACKING-CASE

LABEL-SAFETY

Box LABEL

OPP-TAPE

NOTE) 1) TOTAL : Approx. 10㎏

2) Acceptance number of piling : 5sets
3) Carton size : 390(W) X 320(D) X 470(H)
4) MAX accumulation quantity : 5 cartons

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 33 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
(3) Packing Material

No Part name Quality

1 Static electric protective sack 5
Packing case(Inner box)
2 1 set
included shock absorber
3 Pictorial marking 2 pics
4 Carton 1 set

10. MARKING & OTHERS

A nameplate bearing followed by is affixed to a shipped product at the specified

location on each product.

(1) Parts number : LTM170E8-L01-XXX

(2) Revision code : Two letters
(3) Customer code : One letter
X XX

Revision Code
Customer Code
(4) Lot number : 6 Q 4 D 00111C

Lot Number
Month
Year
Device
Line

(5) Nameplate Indication

Week Code : 0452

LTM170E8-L01
Week
Year
6Q4D00111C XXX
40mm
PPID added

80mm

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 34 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

Approval
(6) Packing box attach

40mm
LTM170E8-L01 Parts Number
XXX Revision Code

Box Serial Number

80mm

(7) Others
1. After service part : None
(Lamps cannot be replaced because of the narrow bezel structure.)

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 35 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

11. Inspection Criteria Approval

When products are shipped, incoming inspection should be carried out with a sampling
inspection based on MIL-STD-105E level II by AQL 1.0%.

CHANGE CONTROL

Design of the product may be changed regarding the specifications, appearance, parts used,
circuits, etc. for product improvement.
If a design change is judged to affect the specifications of this product, supplier should
inform customer of the change in advance.

QUALITY CONTROL

In the event of a product failure under normal operating conditions, a product trouble
or a functional disorder that can be deemed to be the responsibility of supplier, supplier
should repair the fault or replace the product free of charge within one year from the
product delivery date. However, supplier does not take responsibility for the product quality
in the case of modifications not specified by supplier.

MAINTENANCE

The specifications of the functions of maintenance parts may be partially changed

within the range which provides equivalent or better quality.
In principle, maintenance parts should be product units.
When stopping manufacturing this product, supplier should notify customer in advance.

HANDLING OF DOUBTFUL POINTS

Any doubt not stipulated in this specification is to be resolved by mutual agreement

between customer and supplier, and supplier should make efforts for improvement in good
faith.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 36 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

12. General Precautions Approval

12.1 Handling

(a) When the module is assembled, it should be attached to the system firmly
using all mounting holes. Be careful not to twist and bend the module.

(b) Because the inverter use high voltage, it should be disconnected from power
before it is assembled or disassembled.

(c) Refrain from strong mechanical shock and / or any force to the module. In
addition to damage, this may cause improper operation or damage to the module
and CCFT back-light.

(d) Note that polarizers are very fragile and could be damage deasily.
Do not press or scratch the surface harder than a HB pencil lead.

(e) Wipe off water droplets or oil immediately. If you leave the droplets for a long
time, staining or discoloration may occur.

(f) If the surface of the polarizer is dirty, clean it using some absorbent cotton or
soft cloth.

(g) Desirable cleaners are water, IPA(Isopropyl Alcohol) or Hexane.

Do not use Ketone type materials(ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid
or Methyl chloride. It might permanent damage to the polarizer due to chemical
reaction.

(h) If the liquid crystal material leaks from the panel, it should be kept away
from the eyes or mouth . In case of contact with hands, legs or clothes, it must
be washed away with soap thoroughly.

(i) Protect the module from static, or the CMOS Gate Array IC would be damaged.

(j) Use finger-stalls with soft gloves in order to keep display clean during the
incoming inspection and assembly process.

(k) Do not disassemble the module.

(l) Do not pull or fold the lamp wire.

(m) Do not adjust the variable resistor located on the module.

(n) Protection film for polarizer on the module should be slowly peeled off just before use
so that the electrostatic charge can be minimized.

(o) Pins of I/F connector should not be touched directly with bare hands.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 37 / 38

Datasheet pdf - http://www.DataSheet4U.net/
www.DataSheet.co.kr

12.2 Storage Approval

(a) Do not leave the module in high temperature, and high humidity for a long time.
It is highly recommended to store the module with temperature from 0 to 35℃
and relative humidity of less than 70%.

(b) Do not store the TFT-LCD module in direct sunlight.

(c) The module should be stored in a dark place. It is prohibited to apply sunlight or
fluorescent light in storing.

12.3 Operation

(a) Do not connect or disconnect the module in the "Power On" condition.

(b) Power supply should always be turned on/off by the item 6.3
"Power on/off sequence"

(c) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference should be done by system manufacturers. Grounding and shielding methods
may be important to minimize the interference.

(d) The cable between the back-light connector and its inverter power supply should
be connected directly with a minimized length. A longer cable between
the back-light and the inverter may cause lower luminance of lamp(CCFT) and
may require higher startup voltage(Vs).

12.4 Others

(a) Ultra-violet ray filter is necessary for outdoor operation.

(b) Avoid condensation of water. It may result in improper operation or disconnection

of electrode.

(c) Do not exceed the absolute maximum rating value. ( supply voltage variation,
input voltage variation, variation in part contents and environmental temperature,
and so on)
Otherwise the module may be damaged.

(d) If the module keeps displaying the same pattern for a long period of time,
the image may be "sticked" to the screen.
To avoid image sticking, it is recommended to use a screen saver.

(e) This module has its circuitry PCB's on the rear side and should be handled
carefully in order not to be stressed.

(f) Please contact SEC in advance when you display the same pattern for a long time.

Doc . No LTM170E8-L01 Rev.No 04-E00-G-050217 Page 38 / 38

Datasheet pdf - http://www.DataSheet4U.net/