MA2303-EF © 2018 CASIO COMPUTER CO., LTD.

Operation Guide 5544

Using Mobile Link with a Mobile Stopwatch
Contents Phone
Measuring Elapsed Time
Connection
Basic Operations
Connecting with a Phone Timer
Watch Face Items
Canceling a Connection with a Phone
Setting the Timer Start Time
Navigating Between Modes Using the Watch in a Medical Facility or
Aircraft
Using the Timer
Mode Overview Unpairing
If you purchase another phone
Using the Crown Alarm
Configuring World Time Settings
Hand and Day Indicator Movement Configuring Alarm Settings
Adjusting Hand and Day Indicator Alignment
Solar Charging Enabling/Disabling the Alarm
Phone Finder
Connecting with a Phone Stopping an Alarm
Configuring Watch Settings

Adjusting the Time Setting Changing the Home City Summer Time Setting Illumination Light
Connecting with a Phone to Adjust the Checking the Watch Charge Level Turning On the Illumination Light
Watch’s Time

Time Adjustment Using a Time Calibration Adjusting Time Settings Adjusting Hand and Day Indicator
Signal Manually Alignment
Overview
Setting a Home City Adjusting Hand and Day Indicator Alignment
Appropriate Signal Reception Location
Adjusting the Time and Day Setting
Time Calibration Signal Reception
Ranges Moving to Another Time Zone
Configuring the Summer Time Setting (Home
Auto Time Calibration Signal Receive
City)
Manual Time Calibration Signal Receive Other Information
Signal Reception Precautions
World Time City (Time Zone) List
Checking the Last Time Adjustment Result
Specifying a World Time City Summer Time Table
Using the Watch in a Medical Facility or
Configuring the Summer Time Setting (World Supported Phone Models
Aircraft
Time)
Specifications
Swapping Your Home Time and World Time
Mobile Link Precautions

Copyrights and Registered Copyrights

Troubleshooting

1
 Operation Guide 5544
Basic Operations J Last auto time adjustment result
Mode Overview
The second hand points to [Y(YES)] or
This section provides an overview of the watch [N(NO)] to indicate the result of the last ● Timekeeping Mode
and its operations. auto time adjustment operation based on The main hour, minute, and second hands
time signal reception or connection with a indicate the current time.
phone.
Note The small hour and minute hands indicate the
[Y(YES)]: Last time adjustment operation
successful. current World Time.
● The illustrations included in this [N(NO)]: Last time adjustment operation
operation guide have been created to failed. ①

facilitate explanation. An illustration

may differ somewhat from the item it Navigating Between Modes
②
represents.
Press (C) to cycle between modes. 30

● In any mode, hold down (C) for about one Last Time
second to enter the Timekeeping Mode. ③ ④⑤ Adjustment Result
Watch Face Items
Day of week
A Current location time (24-hour time)
One revolution every 24 hours.
① ③
④ B Day of the week at current location
⑤
② ⑥ C World Time hour
Mode hand
Charge level D World Time minute

⑦ E World Time hour (24-hour time)

Timekeeping Mode The hand points to the A-side for a.m.
⑨ times, and to the P-side for p.m. times.

⑩ Checking the Last Time Adjustment

⑧ Result
30
Press (B).
l Checking the Last Time Adjustment Result
C C

A Day of week Connecting with a Phone to Adjust the

In the Timekeeping Mode, the mode hand Watch’s Time
points to the day of the week in the Home Alarm Mode Stopwatch Mode
Hold down (B) for about 0.5 seconds.
City.
Release the button as soon as the second
B Battery level hand moves from [Y/N] to e.
The current charge level is indicated by
the mode hand after you enter the Time Adjustment Using a Time Calibration
Timekeeping Mode. Signal
Hold down (B) for about 1.5 seconds.
C [ST] Release the button as soon as the second
In the Stopwatch Mode, the mode hand C
Timer Mode
C hand moves from e to [RC].
points to [ST].
Phone Finder
D [TR] Hold down (B) for about 3.5 seconds.
In the Timer Mode, the mode hand points
Release the button as soon as the second
to [TR].
hand moves from [RC] to e.
E [AL]
In the Alarm Mode, the mode hand points ● Connecting with a Phone
Swapping the Current Location Time and
to [AL]. World Time
Hold down (C) for about four seconds to
Hold down (A) for about three seconds.
F Summer time setting establish a connection with a phone.
The mode hand points to the current Checking the Charge Level
● To disconnect, press any button.
summer time setting. Immediately after you press (C) to return to the
Before connection Connected Timekeeping Mode, you can check the battery
G e charge level by noting the mode hand
The second hand points to this mark while position.
there is a connection between the watch C
and a phone. l Checking the Charge Level

H [RC] 30 30

The second hand points to [RC] while

calibration signal reception is in progress.
Any button
I Alarm on/off setting
In the Alarm Mode, the second hand
indicates if the alarm is enabled or
disabled.
[ON]: Alarm enabled
[OFF]: Alarm disabled

2
 Operation Guide 5544
● Stopwatch Mode ● Alarm Mode
Important!
The second hand, and the small hour and The small hour and minute hands indicate the
minute hands indicate the elapsed stopwatch alarm time.
time. The second hand indicates the alarm enabled/ ● To prevent loss of water resistance
disabled setting. and/or damage due to impact, be sure
● The main hour and minute hands indicate
to screw the crown in by rotating it
the current time. ● The main hour and minute hands indicate
away from you as you push it in.
the current time.
① Screw in
Start/Stop ①

④
30

30
④
Reset
②③ Enabling/
Disabling the
● When pushing the crown back in, take
②③
Alarm care not to apply too much force.
A Stopwatch seconds
A Alarm enabled/disabled ● Fast Forward/Fast Reverse
B Stopwatch hours
After pulling out the crown, rotating it quickly
B Alarm hour
C Stopwatch minutes in succession in either direction will cause the
hands to move forward or back at high speed.
C Alarm minute
D Stopwatch hours (24-hour time) While the hands are moving forward at high
The hand points to the A-side for hours 0 speed, quickly rotating the crown in
D Alarm hour (24-hour time)
through 12, and to the P-side for hours 12 succession again will increase the speed even
The hand points to the A-side for a.m.
through 24. further.
times, and to the P-side for p.m. times.
● Timer Mode ● Stopping Fast Forward/Fast Reverse
The second hand, and the small hour and Rotate the crown in the direction opposite that
minute hands indicate the current countdown Using the Crown of the ongoing operation or press any button.
time.
● The main hour and minute hands indicate The watch’s crown is a screw-in (screw lock) Note
the current time. type. To use the crown, you first need to rotate
it towards you (leftwards) to loosen it. ● If you do not perform any operation for
①
Start/Stop Crown about two minutes after pulling out the
crown, crown operations will
automatically become disabled. If that
happens, push the crown back in and
30
④ then pull it out again.

Reset
②③ Loosen

Hand and Day Indicator

● Pulling Out and Pushing In the Crown
A Timer seconds Movement
To perform a crown operation, pull it out to the
B Timer hours first or second click and then rotate it. Do not
pull the crown with too much force. Mode hand
C Timer minutes First click
D Timer hours (24-hour time)
The hand points to the A-side for hours 0
through 12, and to the P-side for hours 12
through 24.
30

Normal timekeeping

Second click
Day indicator

● Mode Hand and Day Indicator

Movement
Changing the day setting of the watch will also
cause the mode hand to move.

● Day
● It can take anywhere from about 10 to 40
seconds for the day indicator to change
after timekeeping reaches midnight. The
mode hand moves as the day indicator
changes.
● The day may not be indicated correctly
while the watch’s crown is pulled out.

3
 Operation Guide 5544
● Checking the Charge Level ● Charging Time Guidelines
Solar Charging
Immediately after you press (C) to return to the The table below shows guidelines for
This watch runs on power supplied from a Timekeeping Mode, the mode hand will approximate charging times.
rechargeable (secondary) battery that is indicate the battery charge level. After a short
while, the mode hand will indicate the current Charging Times Required for 1 Day of
charged by a solar panel. The solar panel is Operation
integrated into the face of the watch, and day of the week.
power is generated whenever the face is Approximate
Light Level (Lux)
exposed to light. Charging Time
50,000 8 minutes
● Charging the Watch
10,000 30 minutes
When you are not wearing the watch, put it in ③ 5,000 48 minutes
a location where it is exposed to bright light. ②
500 8 hours
①
Charge Recovery Times
● Sunny day, outdoors (50,000 lux)

Dead battery n Medium 2 hours

charge
30 Medium charge n High 17 hours
charge
High charge n Full charge 5 hours
While you are wearing the watch, make sure
that its face (solar panel) is not blocked from
light by the sleeve of your clothing. Power A Good (high charge) ● Sunny day, near a window (10,000 lux)
generation efficiency is reduced even when
the face of the watch is blocked only partially. B Good (medium charge) Dead battery n Medium 5 hours
charge
C Low Battery Medium charge n High
YES NO 62 hours
charge
● Remaining Charge and Dead Battery
High charge n Full charge 17 hours
You can determine if the charge level is low by
checking the hand movement. Functions
become disabled as battery power goes low.
● Overcast day, near a window (5,000 lux)

Dead battery n Medium 8 hours

Important! charge
Important! Medium charge n High 100 hours
● Should the battery go low or go dead, charge
expose the face (solar panel) to light as 27 hours
Depending on light intensity and local High charge n Full charge
●
soon as possible.
conditions, the watch may become hot
to the touch when exposed to light for ● Indoor fluorescent lighting (500 lux)
charging. Take care to avoid burn Low Battery Power
injury after charging. Also, avoid Dead battery n Medium 87 hours
The second hand jumps at two-second charge
charging the watch under high-
intervals.
temperature conditions like the ones Medium charge n High -
described below. charge
ー On the dashboard of a vehicle
High charge n Full charge -
parked in the sun
ー Near an incandescent light bulb or

other source of heat Note

ー Under direct sunlight or in other hot
30

areas for long periods ● Actual charging time depends on the

Second hand charging environment, watch settings,
and other factors.
Dead Battery
All hands and the day indicator are stopped.

Note

● Exposing the watch face to light after

the battery goes dead will cause the
second hand to revolve
counterclockwise until it stops at
second 57. This indicates charging
has started.

4
 Operation Guide 5544
● Power Saving
Connecting with a Phone Adjusting the Time
Leaving the watch in a dark location for about
one hour between the hours of 10 p.m. and To connect the watch with a phone, first install Setting
5:50 a.m. will cause the second hand to stop,
the CASIO “CASIO WATCHES” app on the Your watch can receive time signals and
and the watch to enter Level 1 power saving.
If the watch is left in this condition for six or phone and then use Bluetooth to pair the connect with a phone to obtain information
seven days, all hands will stop and the watch watch with the phone. that it uses to adjust its date and time setting.
will enter Level 2 power saving.
● A Install the app on your phone.
Level 1 : Important!
Basic timekeeping functions are operational. In Google Play or the App Store, search for the
“CASIO WATCHES” phone app and install it Disable auto time adjustment
Level 2 :
●

on your phone. whenever you are inside an aircraft or

Only the day indicator is operational.
in any other area where radio wave
● B Configure Bluetooth settings.
Note reception is prohibited or restricted.
Enable the phone’s Bluetooth.
l Using CASIO WATCHES to
● Note that the watch also may enter the Configure Settings
power saving state if its face is blocked Note
l Using Watch Operations to
from light by your sleeve while you are Configure Settings
wearing it. ● For details about setting procedures,
● The watch will enter power saving from see your phone documentation.
the Timekeeping Mode only.
Connecting with a Phone to
C Pair the watch with a phone.
● Recovering from Power Saving
●
Adjust the Watch’s Time
Operation Before you can use the watch in combination
Press any button, perform a crown operation, with a phone, you first need to pair them. You can configure watch settings to connect
or place the watch in a well-lit area to recover with a phone at preset times each day and
from power saving. 1. Move the phone to be paired with close to adjust its time settings in accordance with
(within one meter of) the watch. information obtained from an online time
server.
2. Y Tap the “CASIO WATCHES” icon.
● Using This Function
3. Y Tap the of the “My Watch” tab.
Your watch adjusts its time setting four times
a day according to a preset schedule. If you
4. Y Perform the operation shown on the
leave your watch in the Timekeeping Mode, it
phone screen to register the watch to the
will perform the adjustment operation
CASIO WATCHES phone app. automatically as you go about your daily life,
without any operation required by you.
5. X Hold down (C) for about four seconds
until the second hand points to e.
When a connection is established 12:30
between the watch and phone, the
second hand moves to e.
● If pairing fails for some reason, perform
the procedure again from step 1.

Bluetooth mark

Important!

● The watch may not be able to perform

auto time adjustment under the
conditions described below.
Note ー While the watch is too far away from

its paired phone

ー While communication is not possible
● The first time you start up CASIO
WATCHES phone app, a message will due to radio interference, etc.
ー While the phone is updating its
appear on your phone asking if you
want to enable location information system
ー While CASIO WATCHES is not
acquisition. Configure settings to allow
background use of location running on the phone
information.

5
 Operation Guide 5544
Time Adjustment Using a Appropriate Signal Reception
Note
Location
Time Calibration Signal
● The watch will connect with the phone A time calibration signal can be received while
the watch is near a window.
and perform auto time adjustment at Overview
around 12:30 a.m., 6:30 a.m., 12:30
● Keep metal objects away from the watch.
p.m. and 6:30 p.m. The connection is The watch’s time and day settings can be ● Do not move the watch.
automatically terminated after auto adjusted in accordance with a received time ● Do not perform any operation on the watch.
time adjustment is complete. signal.
6 o’clock position

Important!
● Triggering Immediate Time Adjustment
The watch will synchronize its time setting with ● In order to make it possible for the
that of an online time server whenever a current time setting to be adjusted
connection is established between it and a correctly based on time calibration
phone. Perform the operation below to signal reception, you need to specify
connect the watch with a phone whenever you the time zone where you are using the
want to have the watch’s time setting watch.
synchronized with that of an online time
● If the watch was unable to connect with Note
server.
a phone even once for time adjustment
1. Hold down (B) for about 0.5 seconds. during the previous day while ● You may experience time calibration
Release the button as soon as the second connection with a phone is being used, signal reception problems in the areas
it will automatically try to receive a time described below.
hand points to e. ー Among or near buildings
calibration signal.
When the watch connects with a phone, ー While riding in a vehicle

the second hand will move to [Y(YES)], ー Near household appliances, office

and then the watch’s time setting will be machines, mobile phones, etc.
ー On a construction site, in an airport,
synchronized with that of an online time Note
server. or any other location where radio
wave interference occurs
● The connection is terminated ● Areas where time calibration signal ー Near high-voltage lines

automatically after time adjustment is reception is supported are limited. ー In mountainous areas or behind a

complete. When the watch is in an area where mountain

time calibration signal reception is not
possible, connect with a phone to
adjust time and day settings.
l Time Calibration Signal Reception
30 Ranges
● If the watch does not indicate the
correct time even after it receives a
time calibration signal, correct the
Note hand and day indicator positions.
l Using CASIO WATCHES to
● If the watch time is adjusted by Correct Hand Positions
connection with a phone, the watch’s
l Using Watch Operations to
Home City setting will change to the
Correct Hand Positions
city that is being used for the phone’s
time setting. If summer time is in effect
in the city being used for the phone’s
time setting, the watch’s time setting
will also become summer time.
● If the watch does not indicate the
correct time even if it is able to connect
with a phone, adjust the hand and day
indicator positions.
l Adjusting Hand and Day Indicator
Alignment
● If there is a World Time City specified
with CASIO WATCHES, its time will
also be adjusted automatically.

6
 Operation Guide 5544
Time Calibration Signal Reception Auto Time Calibration Signal Manual Time Calibration Signal
Ranges Receive Receive
An automatic time calibration signal receive
● Japan (JJY) operation is performed and the time and day 1. Place the watch near a window or some
The Japan time signal radio stations are settings are adjusted between midnight and
5:00 a.m. Once a signal receive operation is other location appropriate for time signal
located on Mt. Otakadoya in Fukushima and successful, no more auto receive operations reception.
Mt. Hagane in Fukuoka/Saga. are performed that day.
The reception range of the Japanese time 2. Enter the Timekeeping Mode.
Getting Ready
signals is approximately 1,000 km from each l Navigating Between Modes
Enter the Timekeeping Mode.
transmission station.
l Navigating Between Modes 3. Hold down (B) for about 1.5 seconds until
● China (BPC) the second hand points to [RC].

The China time signal radio station is located This indicates that the receive operation
in Shangqiu, Henan Province, China. has started. After the receive operation is
The reception range of the Chinese time complete, the watch’s time and day
settings will be adjusted accordingly.
30
signal is approximately 1,500 km from the
transmission station.
Place the watch near a window or some other
● United States (WWVB)
location appropriate for signal reception.
The United States time signal radio station is ● The second hand points to [RC] while time

located in Fort Collins, Colorado. calibration reception in progress. 30

The reception range of the U.S. time signal is ● When the receive operation is successful,

approximately 3,000 km from the transmission the time and day settings will be adjusted
automatically.
station.

● U.K. (MSF)/Germany (DCF77) Note Note

The U.K. time signal radio station is located in

● Reception takes anywhere from about ● Reception takes anywhere from about
Anthorn, Cumbria.
two minutes to about 10 minutes. It can two minutes to about 10 minutes. It can
The German time signal radio station is take as long as 20 minutes. take as long as 20 minutes.
located in Mainflingen, southeast of Frankfurt. ● If the watch connects with a phone and
The reception range of the U.K. and German adjusts its time setting, the watch will
● Time calibration signal reception is
time signals is approximately 1,500 km from not perform auto receive of a time better at night than during the day.
calibration signal for the rest of that day
each transmission station. or the next day.

Note Signal Reception Precautions

● When the watch is unable to adjust its time
● Even if you are within the normal in accordance with a calibration signal for
reception range of a time calibration some reason, average timekeeping
signal, reception may be made accuracy is within ±15 seconds per month.
impossible by the following factors: ● Note that an internal decoding process the
geographic contours, weather, the
watch performs after it receives a signal
season, the time of day, wireless
may cause the time setting to be slightly off
noise.
(by less than one second).
● Time calibration signal reception is not
possible under the conditions described
below.
ー While battery power is low

ー While in the Stopwatch Mode

ー At Power Saving Level 2

ー While the crown is pulled out

ー While the Home City setting is one where

time signal reception is not possible

ー While the watch is outside the time signal

reception range
● As of January 2018, China does not
observe summer time. If China starts to
observe summer time in the future, the time
displayed by the watch for China may not be
correct.

7
 Operation Guide 5544
Checking the Last Time Using the Watch in a Medical Using Mobile Link with
Adjustment Result Facility or Aircraft a Mobile Phone
Whenever you are in a hospital, on an aircraft, While there is a Bluetooth connection
1. Enter the Timekeeping Mode.
or in any other location where auto time between the watch and phone, the watch time
l Navigating Between Modes calibration signal receive or connection with a setting is adjusted automatically. You can also
phone may cause problems, you can perform change the watch’s other settings.
the procedure below to disable such
operations. To re-enable auto time Note
adjustment, perform the same operation
again. This function is available only while
30
●

CASIO WATCHES is running on the

1. Enter the Timekeeping Mode. phone.
2. Press (B). l Navigating Between Modes ● This section describes watch and
The second hand points to the result of the phone operations.
last auto time adjustment operation. The
X : Watch operation
watch hands will return to indicating the
current time if you do not perform any
Y : Phone operation
operation for nine or ten seconds.
30

[Y(YES)]: Last time adjustment operation

successful. Connection
[N(NO)]: Last time adjustment operation 2. Press (B).
failed. The second hand will indicate the last
Connecting with a Phone
receive result for nine or ten seconds.
Second hand This section explains how to establish a
Bluetooth connection with a phone that is
paired with the watch.
● If the watch is not paired with the phone you
30 want to connect with, refer to the information
30 below and pair them.
l C Pair the watch with a phone.

Note 1. Move the phone close to (within one meter

3. Within 10 seconds after pressing (B)
of) the watch.
above, pull out the crown to the first click.
● Even if there was a successful time
calibration signal receive operation or
● If more than 10 seconds elapse before 2. X While the second hand is not pointing to
connection with a phone, the second you pull out the crown after you perform e, hold down (C) for about four seconds.
hand will point to [N(NO)] if you the operation in step 2, the second hand
This causes the second hand to move to
adjusted the time and/or date setting will return to indicating seconds. If this
happens, perform step 2 again. e and establishes a connection between
manually.
the watch and phone.
4. Rotate the crown to disable auto time
adjustment.
[Y(YES)]: Auto time adjustment enabled.
[N(NO)]: Auto time adjustment disabled.

30
Important!
Crown
● If you have problems establishing a
connection, it could mean that CASIO
5. Push the crown back in. WATCHES is not running on the
phone. On the phone’s home screen,
Note tap the “CASIO WATCHES” icon. After
the app starts up, hold down the
● If the watch is paired with a phone, watch’s (C) button for about four
CASIO WATCHES can be used to seconds.
disable auto time adjustment.
l Using CASIO WATCHES to
Disable Auto Time Adjustment

8
 Operation Guide 5544
Unpairing ● To select a World Time City
Note

1. X If the watch is connected with a phone, 1. Y Tap the “CASIO WATCHES” icon.
● The connection will be terminated if
press any button to terminate the
you do not perform any operation on 2. X Hold down (C) for about four seconds.
connection.
the watch or phone for a fixed amount This causes the second hand to move to
of time. Connected Disconnected
e and establishes a connection between
To specify the connection limit time,
the watch and phone.
perform the following operation with
CASIO WATCHES: “Watch settings”
n “Connection time with the app”.
Next, select a setting of 3 minutes, 5
30 30

minutes, or 10 minutes.

2. Y Tap the “CASIO WATCHES” icon.

Canceling a Connection with a
Phone 3. Y Perform the operation shown on the
phone screen to unpair.
3. Y Perform the operation shown on the
Pressing any button terminates the Bluetooth
phone screen. The World Time setting will
connection and returns the second hand to its If you purchase another phone be reflected on the watch.
normal operation.
You need to perform the pairing operation ● You can determine whether a World
Connected Disconnected whenever you want to establish a Bluetooth Time is a.m. or p.m. by checking the
connection with a phone for the first time. position of the small 24-hour hand.
l C Pair the watch with a phone.

30 30

Configuring World Time

Settings
30

Using the Watch in a Medical Facility

Specifying a World Time City with CASIO
or Aircraft WATCHES causes the watch’s World Time
Whenever you are in a hospital, on an aircraft, City to change accordingly. The standard
or in any other location where auto time time/summer time setting of the World Time
calibration signal receive or connection with a will be adjusted automatically without any
phone may cause problems, you can perform watch operation required by you. World Time hour and minute
the procedure below to disable such
World Time hour (24-hour)
operations. To re-enable auto time
adjustment, perform the same operation
again.

1. Y Tap the “CASIO WATCHES” icon.

2. X Hold down (C) for about four seconds. 30

This causes the second hand to move to

e and establishes a connection between
the watch and phone.

Note

● CASIO WATCHES World Time lets

you select from among approximately
300 cities as the World Time City.

3. Y Perform the operation shown on the

phone screen to enable or disable auto
time adjustment.

9
 Operation Guide 5544
● Configuring the Summer Time Setting ● Swapping Your World Time and Home
Adjusting Hand and Day
Time
1. Y Tap the “CASIO WATCHES” icon. Indicator Alignment
1. Y Tap the “CASIO WATCHES” icon.
2. X Hold down (C) for about four seconds. If the hands and/or date indicator are out of
2. X Hold down (C) for about four seconds. alignment even though auto time adjustment
This causes the second hand to move to
is being performed, use CASIO WATCHES to
e and establishes a connection between This causes the second hand to move to
adjust them.
the watch and phone. e and establishes a connection between
the watch and phone. 1. Y Tap the “CASIO WATCHES” icon.

2. X Hold down (C) for about four seconds.

This causes the second hand to move to
e and establishes a connection between
the watch and phone.

3. Y Perform the operation shown on the

phone screen to select a summer time 3. Y Perform the operation shown on the
setting. phone screen to swap your Home Time
● “Auto” with your World Time.
The watch switches between standard For example, if your Home City is Tokyo
time and summer time automatically. and the World Time City is New York, they
● “OFF” will be swapped as shown below. 3. Y Perform the operation shown on the
The watch always indicates standard phone screen to correct hand and day
time. Before swapping After swapping indicator alignment.
● “ON” Home City Home City
The watch always indicates summer
(Tokyo) (New York) Note
time.
● The movement of some hands are
Note linked with other hands. When
correcting the alignment of such a
hand, you will have to correct the
30 30
● While the summer time setting is
“Auto”, the watch will switch between alignment of the linked hand(s) at the
standard time and summer time World Time City World Time City same time.
(New York) (Tokyo)
automatically. You do not need to
switch between standard time and
summer time manually. Even if you are Note
in an area that does not observe
summer time, you can leave the ● Auto time adjustment does not work for
watch’s summer time setting as “Auto”. 24 hours after swapping of the Home
● Changing the time setting manually Time and World Time.
with a watch operation will cancel auto
standard time/summer time switching.
● CASIO WATCHES screen shows
information about summer time
periods.

10
 Operation Guide 5544
Phone Finder Configuring Watch Settings Checking the Watch Charge
Level
You can use phone finder to trigger a tone on You can use CASIO WATCHES to specify the
the phone to make it easy to find. The tone is amount of time until the Bluetooth connection Use the procedure below to check the current
forced to sound even if the phone is in vibrate is automatically terminated, and to configure charge level with CASIO WATCHES.
mode. other watch settings.
1. Y Tap the “CASIO WATCHES” icon.
Important! 1. Y Tap the “CASIO WATCHES” icon.
2. X Hold down (C) for about four seconds.
2. X Hold down (C) for about four seconds.
● Do not use this function in areas where This causes the second hand to move to
phone call tones are restricted. This causes the second hand to move to
e and establishes a connection between
● The tone sounds at a high volume. Do e and establishes a connection between the watch and phone.
not use this function when listening to the watch and phone.
phone output over earphones.

1. X If the watch is connected with a phone,

press any button to terminate the
connection.

Connected Disconnected
3. Y Use CASIO WATCHES to check the
3. Y Select the setting you want to change charge level.
and then perform the operation shown on
the phone screen.
30 30

Changing the Home City Adjusting Time

2. X Hold down (C) for about 2 seconds. Summer Time Setting Settings Manually
This will cause the watch to enter the
Timekeeping Mode. You can use the procedure below to adjust the
1. Y Tap the “CASIO WATCHES” icon.
watch’s time and day settings when time
3. X Hold down (B) for about 3.5 seconds calibration signal reception or communication
2. X Hold down (C) for about four seconds.
until the second hand points to e. with a phone is not possible for some reason.
This causes the second hand to move to
A connection will be established between
e and establishes a connection between
the watch and phone, and then the
the watch and phone.
phone’s ringtone will sound. Setting a Home City
● It will take a few seconds before the
phone tone sounds. Use the procedure in this section to select a
city (time zone) to use as your Home City.

1. Pull out the crown to the second click.

The second hand indicates the currently
selected Home City time zone, while the
mode hand indicates the current summer
3. Y Perform the operation shown on the time setting.
phone screen to change your Home City ● If the Home City setting is a city (time
summer time setting. zone) that cannot be set on the watch,
4. X Press any button to stop the tone. the second hand will point to .
● You can press any watch button to stop
the phone tone, but only during the first Summer time setting
30 seconds after it starts to sound.

30
Crown

Home City

11
 Operation Guide 5544
2. Rotate the crown to change the Home 8. Press (C).
Configuring the Summer
City. Time Setting (Home City)
This enables the year one’s digit setting
● You can also select a time zone whose operation.
If you are in an area that observes summer
name is not indicated on the face of the
9. Rotate the crown to move the second time, you can also configure a summer time
watch.
hand to the desired setting for the year setting.
● For details about time zones, refer to the one’s digit.
information below. Note
l City (Time Zone) List Year (one’s digit)
0
3. Push the crown back in to its normal
1 ● The initial factory default summer time
position.
2 setting for all cities is [AT (AUTO)]. In
9 3
many cases, the [AT (AUTO)] setting
lets you use the watch without
8 4 switching between summer time and
Adjusting the Time and Day 7 5 standard time.
Setting
6
● When performing a manual operation
10. Press (C). to select a time zone for which there is
1. Pull out the crown to the second click. no city name displayed, use [STD] or
This enables the month setting operation.
[DST] for the summer time setting.
The second hand will move to the city
code of the currently selected Home City.
12
11 1
● The mode hand will point to the summer 10 2

time setting for the currently selected

1. Pull out the crown to the second click.
9 3
Home City. The second hand will move to the city
8 4 code of the currently selected Home City.
Summer time setting 7
6
5 ● The mode hand will point to the summer
Month time setting for the currently selected
Home City.
11. Rotate the crown to change the month.
2. Hold down (A) for about one second.
12. Press (C).
30
Crown Each time you hold down (A) for about one
Home City (time zone) The mode hand will move slightly, second, the summer time setting will cycle
indicating that the day setting operation is to the next available option.
enabled.
2. Hold down (C) for about one second.
This causes the second hand to move to
12 o’clock, and enables the minute setting
operation. 30

3. Rotate the crown to change the minute 30

setting. ● [AT (AUTO)]

4. Press (C). The watch switches between standard
Day
time and summer time automatically.
The hour hand will move slightly, ● Changing the day setting will cause the [STD]
indicating that the hour setting operation
●

mode hand to rotate repeatedly. The watch always indicates standard

is enabled.
l Hand and Day Indicator Movement time.
5. Rotate the crown to change the hour
13. Rotate the crown to change the day. ● [DST]
setting.
The watch always indicates summer
14. On a time signal at the top of a minute, time.
6. Press (C).
push the crown back in.
This enables the year ten’s digit setting 3. Push the crown back in to its normal
operation. Note position.

7. Rotate the crown to move the second

hand to the desired setting for the year
● If the watch does not indicate the
ten’s digit. correct time even after you adjust it,
adjust the hand and day indicator
Year (10’s digit) positions.
00
10 l Using CASIO WATCHES to
20 Correct Hand Positions
l Using Watch Operations to
90 30
Correct Hand Positions
80 40
70 50
60

12
 Operation Guide 5544
World Time 2. Rotate the crown to change the World 2. Hold down (A) for about one second.
World Time lets you look up the current time Time City (time zone). Each time you hold down (A) for about one
in any one of 27 cities and 39 time zones The World Time hour and minute hands second, the summer time setting will cycle
around the globe. indicate the current time in the selected to the next available option.
time zone. ● [AT (AUTO)]
● You can also select a time zone whose The watch switches between standard
name is not indicated on the face of the time and summer time automatically.
watch. ● [STD]
● For details about time zones, refer to the The watch always indicates standard
information below. time.

30
l City (Time Zone) List ● [DST]
World Time hour (24-hour) The watch always indicates summer
time.

Getting Ready
Enter the Timekeeping Mode. 30

l Navigating Between Modes Crown

30

World Time hour and minute

3. Push the crown back in. 3. Push the crown back in to its normal
30
position.

Configuring the Summer

Time Setting (World Time) Swapping Your Home Time
and World Time
Specifying a World Time City If you are in an area that observes summer
time, you can also configure a summer time Holding down (A) for about three seconds will
Use the procedure below to specify the city setting. swap your Home Time with your World Time.
(time zone) whose time you want to view.
● Pressing (A) will cause illumination to turn
Note on. Keep the button depressed for about
1. Pull out the crown to the first click.
three seconds.
The second hand indicates the currently ● The initial factory default summer time
selected World Time City, while the mode setting for all cities is [AT (AUTO)]. In Before swapping After swapping
hand indicates the World Time City’s many cases, the [AT (AUTO)] setting
summer time setting. lets you use the watch without Home Time World Time
● If the World Time City setting is a city switching between summer time and
(time zone) that cannot be set on the standard time.
watch, the second hand will point to ● When performing a manual operation
. to select a time zone for which there is 30 30

no city name displayed, use [STD] or

World Time City (time zone)
[DST] for the summer time setting.
World Time Home Time
● While [UTC] is selected as the city, you
will not be able to change or check the
summer time setting.
● If a swapping operation causes a change in
30 the day indicator setting, the mode hand will
Crown rotate repeatedly.
l Hand and Day Indicator Movement
1. Pull out the crown to the first click.
Summer time setting

The second hand will point to the currently Note

selected World Time City (time zone).
● The mode hand will move to the ● This function comes in handy when
summer time setting of the currently you need to move to another time
selected World Time City (time zone). zone. For details about how to use it,
go to the section below.
l Moving to Another Time Zone

13
 Operation Guide 5544
Stopwatch Timer Using the Timer
The stopwatch measures elapsed time in units The timer counts down from a start time
of one second up to 23 hours, 59 minutes, 59 specified by you. A beeper sounds when the 1. Press (A) to start the countdown.
seconds (24 hours). end of the countdown is reached.

Getting Ready
● The beeper is muted in the cases described
below.
Enter the Stopwatch Mode. ー When battery power is low

l Navigating Between Modes

Getting Ready 30

Enter the Timer Mode.

l Navigating Between Modes

A beeper sounds for 10 seconds when the

30 end of the countdown is reached.
● To pause an ongoing countdown, press
(A). To reset a paused countdown to the
30 start time, press (B).

2. Press any button to stop the tone.

Measuring Elapsed Time 3. Press (C) twice to return to the
Timekeeping Mode.
Hours
Setting the Timer Start Time

1. Pull out the crown to the first click.

Alarm
30
2. Rotate the crown to change the
countdown start time setting. The watch will beep when the alarm time is
Seconds Hour (24-hour time)
● The countdown start time can be set in reached.
Minutes
1-minute units up to 24 hours. ● The beeper is muted in the cases described
below.
24-hour
1. Use the operations below to measure ー When battery power is low
Seconds
ー When watch is at Level 2 power saving
elapsed time.
Start l Power Saving
Getting ready
Stop
30
Enter the Alarm Mode.
Crown l Navigating Between Modes
Resume
Hours Minutes

Stop
3. Push the crown back in.
2. Press (B) to reset the elapsed time to all
Note 30
zeros.

3. Press (C) three times to return to the ● You can set a countdown start time of
Timekeeping Mode. 24 hours by aligning the small 24-hour
hand with 24.

14
 Operation Guide 5544
Configuring Alarm Settings Illumination Light Adjusting Hand and
The watch has an LED light that you can turn Day Indicator
1. Pull out the crown to the first click. on for reading in the dark. When you turn on
the LED light, it gradually becomes brighter.
Alignment
This turns on the alarm.
After about two seconds, it gradually becomes Strong magnetism or impact can cause the
2. Rotate the crown to change the alarm time dimmer until it turns off. hands and/or the day indicator to go out of
setting.
alignment. If this happens, adjust hand and
Getting ready
Alarm on day indicator alignment.
Enter the Timekeeping Mode or Alarm Mode.
● The watch performs alignment of the hour
l Navigating Between Modes
hand, minute hand, second hand, and 24-
hour hand automatically.
Timekeeping Mode Alarm Mode
30

Crown
Adjusting Hand and Day
Indicator Alignment
Hours Minutes
30 30

3. Push the crown back in.

1. Pull out the crown to the second click.
4. Press (C) once to return to the
Timekeeping Mode.
2. Hold down (B) for about five seconds, until
Turning On the Illumination the second hand moves to 12 o’clock.
Note Light Release the button when the second hand
reaches 12 o’clock.
Pressing (A) turns on illumination. This will start auto alignment of the hour
● A beeper sounds for 10 seconds when
an alarm time is reached. hand, minute hand, second hand, and 24-
hour hand.
● After auto alignment is complete, the
hands should be in the positions shown
Enabling/Disabling the Alarm 30
below.

24-hour hand
1. Press (B) to toggle the alarm between on ● Illumination will turn off automatically if an
and off. alarm starts to sound.

Alarm on
● Illumination is disabled while the hands are
moving at high speed.

Note Minute hand Hour hand

30
● You can also use CASIO WATCHES
to change the illumination duration.
Alarm off l Configuring Watch Settings 30

Crown

2. Press (C) once to return to the Second hand

Timekeeping Mode.

Stopping an Alarm
While the alarm is sounding, press any button
to stop it.

15
 Operation Guide 5544
3. Press (C). 7. Press (C).
Moving to Another Time
Confirm that the small hour and minute Confirm that the day indicator shows “1”. Zone
hands, and the small 24-hour hand are all
Use the procedure below to easily change day
stopped at 12 o’clock.
and time settings of the watch to a destination
Small 24-hour hand location.

11 ● Before Boarding

1. Configure the World Time to the current

Day
30 time at your destination.
● Changing the date setting will cause the
mode hand to rotate repeatedly. In
Small hour hand Small minute hand
some cases, the mode hand may
continue to rotate for about 5 minutes.
4. If the small hour and minute hands, and
Current time
l Hand and Day Indicator Movement
the small 24-hour hand are not at 12
o’clock, rotate the crown to align them with 8. If “1” is not shown for the day, rotate the
12 o’clock. crown until “1” is shown for the day. 30

● The mode hand moves in conjunction

5. Press (C).
with crown rotation. Move the mode Destination time
Confirm that the mode hand is stopped at hand to 12 o’clock.
12 o’clock, and check if the day is l Using CASIO WATCHES to Configure
indicated properly. 9. Push the crown back in. Settings
l Using Watch Operations to Configure
Note
Mode hand
Settings

● Leaving the crown pulled out for more

2. Disable auto time adjustment.
than approximately 30 minutes without
330
0 performing any operation will
automatically cause the adjustment
Day (Operation start day) operation to become disabled. If this
happens, push the crown back in to its 30

normal position and then pull it out

6. If the mode hand and/or the day indicator
again to restart the procedure from the
is out of alignment, rotate the crown to
beginning. Pushing the crown in to its
move the mode hand to 12 o’clock and the l Using CASIO WATCHES to Configure
normal position part way through the
day to the center of the indicator window. Settings
alignment procedure will cause the
The movement range of the mode hand l Using Watch Operations to Configure
●
hands to return to their normal position.
and day indicator is limited when you Settings
Any alignment you performed up to
rotate the crown. The maximum left- that point will be applied. ● After Arriving
right movement of the mode hand is 180
degrees in either direction. The day 1. Swap the origin time zone time with the
indicator moves only slightly. destination time zone time.
● After the mode hand and day indicator
are in the positions you want, advance Before swapping After swapping
to step 9 of this procedure. If you are Destination time
unable to make the adjustments you
want, go to step 7.

30 30

Destination time

l Using CASIO WATCHES to Configure

Settings
l Using Watch Operations to Configure
Settings

2. Enable auto time adjustment.

l Using CASIO WATCHES to Configure
Settings
l Using Watch Operations to Configure
Settings

16
 Operation Guide 5544
Other Information Summer Time Table Summer Time Summer Time
City name
Start End
This section provides non-operational When [AT (AUTO)] is selected for a city that
01:00, last 02:00, last
information you also need to know. Refer to observes summer time, switching between
London Sunday in Sunday in
this information as required. standard time and summer time will be
March October
performed automatically at the timing shown
02:00, last 03:00, last
in the table below.
Paris Sunday in Sunday in
City (Time Zone) List March October
Note
03:00, last 04:00, last
You can specify a time zone whose city code
Athens Sunday in Sunday in
is not shown on the face by aligning the ● Summer time start and end dates for
March October
second hand with the applicable UTC offset. your current location may be different
02:00, first
from those shown below. If this 03:00, first
Second Sydney Sunday in
City happens, you can have new summer Sunday in April
City name Hand Offset October
code time information for your Home City
Position 02:00, last
and World Time City sent to the watch 03:00, first
Coordinated Wellington Sunday in
UTC 0 0 by connecting the watch with a phone. Sunday in April
Universal Time September
If the watch is not connected with a
LON* London 2 0 phone, you can change the summer 02:00, second 02:00, first
PAR* Paris 4 +1 time setting manually. Anchorage Sunday in Sunday in
ATH* Athens 6 +2 March November
JED Jeddah 8 +3 02:00, second 02:00, first
Los
- - 9 +3.5 Sunday in Sunday in
Angeles
DXB Dubai 10 +4 March November
- - 11 +4.5 02:00, second 02:00, first
Denver Sunday in Sunday in
- - 12 +5
March November
DEL Delhi 13 +5.5
02:00, second 02:00, first
- - 14 +5.75
Chicago Sunday in Sunday in
DAC Dhaka 15 +6
March November
- - 16 +6.5
02:00, second 02:00, first
BKK Bangkok 17 +7 New York Sunday in Sunday in
HKG* Hong Kong 19 +8 March November
- - 20 +8.5 02:00, second 02:00, first
- - 21 +8.75 Halifax Sunday in Sunday in
TYO* Tokyo 22 +9 March November
- - 23 +9.5 00:00, third
SYD Sydney 24 +10 Sunday in
00:00, third
- - 25 +10.5 Rio de February or
Sunday in
NOU Noumea 26 +11 Janeiro 00:00, fourth
October
WLG Wellington 28 +12 Sunday in
February
- - 29 +12.75
TBU Nuku’alofa 30 +13 ● The information in the above table is current
CXI Kiritimati 32 +14 as of January 2018.
BAR Baker Island 36 -12
PPG Pago Pago 38 -11
HNL Honolulu 40 -10 Supported Phone Models
- - 41 -9.5
For information about supported phone
ANC Anchorage 42 -9
models, visit the CASIO Website.
LAX* Los Angeles 44 -8
https://world.casio.com/os_mobile/wat/
DEN* Denver 46 -7
CHI* Chicago 48 -6
NYC* New York 50 -5
YHZ* Halifax 52 -4
- - 53 -3.5
RIO Rio de Janeiro 54 -3
Fernando de
FEN 56 -2
Noronha
RAI Praia 58 -1
* Time zones where time calibration signal
reception is possible.
● The information in the above table is current
as of January 2018.

17
 Operation Guide 5544
Specifications Timer : Mobile Link Precautions
Setting unit: 1 minute
Accuracy at normal temperature : ● Legal Precautions
Countdown range: 24 hours
±15 seconds per month average when time Measuring unit: 1 second
● This watch complies with or has received
adjustment by time calibration signal 10-second beeper when the end of the approval under the radio laws of various
reception or by communication with a countdown is reached countries and geographical areas. Using
phone is not possible. this watch in an area where it does not
Alarm : comply with or has not received approval
Timekeeping :
Setting units: Hours, minutes under applicable radio laws may be a
Hour, minute, second, day (2000 to 2099 Beeper: 10 seconds criminal offense. For details, visit the CASIO
full auto calendar), day of the week Website.
Other :
World Time : https://world.casio.com/ce/BLE/
LED light, auto hand position correction,
Current time in 27 cities (39 time zones), ● Use of this watch inside of aircraft is
Power Saving, battery indicator
and UTC (Coordinated Universal Time) restricted under the aviation laws of each
time Power Supply : country. Be sure to follow the instructions of
Auto summer time setting Solar panel and one rechargeable battery airline personnel.
Home Time swapping
Approximate Battery Life : ● Precautions when using Mobile Link
Signal Receive Functions : Approximately 5 months ● When using this watch in combination with
Time calibration: Auto Receive, manual Conditions a phone, keep the watch and phone close
receive Auto adjust: 4 times/day to each other. A range of two meters is
Auto transmitter selection (for JJY, MSF/ Light: 1 operation/day recommended as a guideline, but the local
DCF77) Alarm: 1 operation/day environment (walls, furniture, etc.), the
Power Saving: 6 hours/day structure of a building, and other factors
Receivable Call Signs : may require a much closer range.
JJY (40kHz/60kHz), BPC (68.5kHz),
Specifications are subject to change without
● This watch can be affected by other devices
WWVB (60kHz), MSF (60kHz), DCF77
notice. (electrical devices, audio-visual equipment,
(77.5kHz)
office equipment, etc.) In particular, it can
Last reception result display be affected by operation of a microwave
Automatic and manual switching between oven. The watch may not be able to
standard time and summer time. communicate normally with a phone if a
Mobile Link : microwave oven is operating nearby.
Conversely, this watch may cause noise in
Auto Time Correction
radio reception and the video image of a TV.
Time setting adjusted automatically at
preset time
● Bluetooth of this watch uses the same
One-touch Time Correction frequency band (2.4 GHz) as wireless LAN
devices, and use of such devices in close
Manual connection and time adjustment
proximity of this watch may result in radio
Phone finder
interference, slower communication
Watch operation sounds the alert sound
speeds and noise for the watch and the
of the phone.
wireless LAN device, or even
Home Time swapping
communication failure.
Auto summer time setting
Automatic switching between standard
time and summer time
Hand alignment correction
Data Communication Specifications
Bluetooth®
Frequency Band: 2400MHz to 2480MHz
Maximum Transmission: 0 dBm (1 mW)
Communication range: Up to 2 meters
(depends on environment)

Stopwatch :
Measuring unit: 1 second
Measuring capacity: 23:59’59” (24 hours)
Measurement function: Elapsed time

18
 Operation Guide 5544
● Stopping Radio Wave Emission by This
Watch
Troubleshooting Q2 The signal receive operation always
fails.
The watch is emitting radio waves whenever
the second hand is pointing to e. Is the watch in a location that is appropriate
Signal Reception (Time
Even if the second hand is not pointing at e, for signal reception?
the watch will automatically attempt to Calibration Signal)
Check your surroundings and move the
connect with a phone four times a day to adjust
watch to a location where signal reception
its time settings. Q1 The watch cannot perform a receive is better.
When in a hospital, on an aircraft, or in any operation. l Appropriate Signal Reception Location
other area where the use of radio waves is not
allowed, use the operation below to stop radio Is the watch’s battery charged? Did you avoid touching the watch while the
wave generation. receive operation was in progress?
Signal reception is not possible while
● Stopping Radio Wave Generation
battery power is low. Keep the watch Minimize movement of the watch and do
Press (C) to terminate the Bluetooth
exposed to light until it recharges not perform any watch operation while a
connection.
sufficiently. receive operation is in progress.
Connected Disconnected l Solar Charging
Is there an alarm configured to sound
Is the watch in the Timekeeping Mode? during the same period that the signal
receive operation is performed?
The watch cannot receive time calibration
30 30 signals while auto adjustment is disabled Receive stops if an alarm operation starts
or while the watch is in a mode other than while it is being performed. Disable the
the Timekeeping Mode. Return to the alarm.
● Disabling Auto Time Adjustment Timekeeping Mode. l Enabling/Disabling the Alarm
Configure CASIO WATCHES settings to l Navigating Between Modes
disable synchronization between the watch Is the signal transmitter in your area
and phone. Is your Home City setting correct for your transmitting a signal?
l Using CASIO WATCHES to Disable location?
The transmitter of the time calibration may
Auto Time Adjustment not be transmitting a signal.
The watch will not indicate the correct time
if the Home City setting is wrong. Change Try again later.
your Home City setting so it correctly
Copyrights and Registered reflects your location. Q3 Signal reception should have been
Copyrights l Setting a Home City successful, but the watch’s time and/
or day is wrong.
● The Bluetooth® word mark and logos are After checking the above, the watch still
registered trademarks owned by the cannot perform a receive operation.
Is the time zone where you are using the
Bluetooth SIG, Inc. and any use of such Time calibration signal reception is not watch specified correctly?
marks by CASIO Computer Co., Ltd. is possible under the conditions described
under license. Specify the time zone where you are using
below.
● iPhone and App Store are trademarks of the watch.
● When watch is at Level 2 power saving
Apple Inc. in the United States and other l Configuring the Summer Time Setting
● When the crown is pulled out (Home City)
countries.
● Timer countdown operation in progress l Configuring the Summer Time Setting
● iOS is a trademark or registered trademark
If successful reception is not possible for (World Time)
of Cisco Systems, Inc.
some reason, you can adjust the time and
● GALAXY, GALAXY Note, and GALAXY S Is the hand and/or day indicator alignment
day settings manually.
are registered trademarks of Samsung correct?
Electronics Co., Ltd.
Adjust hand and/or day indicator
● Android and Google PlayTM are trademarks
alignment.
or registered trademarks of Google LLC.
l Adjusting Hand and Day Indicator
● Other company names and product names Alignment
used herein are trademarks or registered
trademarks of their respective companies. After checking the above, the time and/or
day settings is still wrong.

Adjust time and day settings manually.

l Adjusting Time Settings Manually

19
 Operation Guide 5544
I can’t pair the watch with a I can’t reconnect the watch Q2 I can’t connect while my phone is in
the Airplane Mode.
phone. and phone.
Connection with the watch is not possible
while the phone is in the Airplane Mode. After
Q1 I’ve never been able to establish a Q1 The watch will not re-connect with the exiting the phone’s Airplane Mode, go to the
(pairing) connection between the phone after they are disconnected.
phone’s Home Screen and tap the “CASIO
watch and phone. WATCHES” icon. Then on the watch, hold
Is CASIO WATCHES running? down the MODE button (C) for about four
Are you using a supported phone model? seconds.
The watch cannot re-connect with the
Check if the phone model and its phone unless CASIO WATCHES is
operating system are supported by the running on the phone. On the phone’s
watch. Home Screen, tap the “CASIO
For information about supported phone WATCHES” icon. Then on the watch, hold
models, visit the CASIO Website. down the MODE button (C) for about four
30

https://world.casio.com/os_mobile/wat/ seconds.

Did you install CASIO WATCHES on your

Q3 I changed the phone’s Bluetooth
phone?
from enabled to disabled, and now I
CASIO WATCHES needs to be installed 30 can’t connect anymore.
on your phone in order to connect with the
On the phone, re-enable Bluetooth, and then
watch.
go to the Home Screen and tap the “CASIO
l A Install the app on your phone. WATCHES” icon. Next, on the watch, hold
Have you tried turning your phone off and
then back on again? down the MODE button (C) for about four
Are your phone’s Bluetooth settings seconds.
configured correctly? Turn the phone off and then back on, and
then tap the “CASIO WATCHES” icon.
Configure the phone’s Bluetooth settings.
Next, on the watch, hold down the MODE
For details about setting procedures, see
button (C) for about four seconds.
your phone documentation.
iPhone Users
30

● “Settings” n “Bluetooth” n On
Android Users
Q4 I can’t connect after turning off the
30

● Enable Bluetooth.
phone.
Other than the above. Turn on the phone and tap the “CASIO
Is a timer countdown operation in WATCHES” icon. Then on the watch, hold
Some phones need to have BT Smart progress? down the MODE button (C) for about four
disabled to use CASIO WATCHES. For
Connection with a phone is not possible seconds.
details about setting procedures, see your
phone documentation. while there is 30 seconds or less
remaining on a countdown timer
On the Home Screen, tap: “Menu” n
operation. Stop the countdown operation
“Settings” n “Bluetooth” n “Menu” n before connecting with the phone.
“BT Smart settings” n “Disable”. 30

20
 Operation Guide 5544
Phone-Watch Connection Auto Time Adjustment by Alarm
Bluetooth Connection (Time
Q1 I can’t establish a connection Adjustment) Q1 The alarm does not sound.
between the phone and watch.
Is the watch’s battery charged?
Q1 When does the watch adjust its time?
Have you tried turning your phone off and
Keep the watch exposed to light until it
then back on again? The watch will connect with the phone and
recharges sufficiently.
perform auto time adjustment at around 12:30
Turn the phone off and then back on, and
a.m., 6:30 a.m., 12:30 p.m. and 6:30 p.m. The l Solar Charging
then tap the “CASIO WATCHES” icon.
connection is automatically terminated after
Next, on the watch, hold down the MODE The crown is pulled out.
auto time adjustment is complete.
button (C) for about four seconds.
The alarm will not sound while the crown
is pulled out. Push the crown back in to its
Q2 Auto time adjustment is not
normal position.
performed at a scheduled time.

Is the alarm enabled?

30
Is auto time adjustment not being
performed according to its normal Enable the alarm.
schedule? l Enabling/Disabling the Alarm
Has the watch been re-paired with the Note that auto time adjustment is not
phone? performed for 24 hours after swapping of
the Home Time and World Time, or after Hand Movement and
After deleting pairing information from
CASIO WATCHES, re-pair the watch and
the time setting is adjusted manually on Indications
the watch. Auto time adjustment will
phone.
resume 24 hours after either of the above
l Unpairing Q1 I don’t know what mode the watch is
operations is performed.
in.
If you are unable to establish a
Is auto time adjustment enabled? You can determine the current mode by
connection...
Auto time adjustment will not be checking the mode hand position. Use (C) to
Use the procedure below to delete the
performed at the scheduled times unless navigate between modes.
pairing information from the watch, and
it is enabled. Enable auto time l Navigating Between Modes
then re-pair the watch and phone.
adjustment.
A Pull out the crown to the second click. l Using CASIO WATCHES to Configure
Settings
B Hold down (B) for about 10 seconds. l Using Watch Operations to Configure
This deletes the pairing information. Settings 30

The second hand will point to e.

Q3 Time is not displayed correctly.
C Push the crown back in.
The phone’s time setting may be incorrect Q2 The second hand is jumping at two-
because it is unable to connect with its second intervals.
network due to being out of range, etc. If this
Battery power is low. Keep the watch exposed
Changing to a Different happens, connect the phone to its network
to light until it recharges sufficiently.
Phone Model and then adjust the time setting.
l Solar Charging

Q1 Connecting the current watch to Q3 All hands are stopped and buttons do
another phone. not work.

Pair the watch with the phone. The battery is dead. Keep the watch exposed
l If you purchase another phone to light until it recharges sufficiently.
l Solar Charging

21
 Operation Guide 5544
Q4 The hands suddenly start moving at Crown Operations
high speed.

This is due to the reason (or one of the Q1 Nothing happens when I rotate the
reasons) below, and does not indicate crown.
malfunction. Simply wait until normal hand
movement resumes. If you do not perform any operation for about
two minutes after pulling out the crown
● The watch is recovering from a power
(approximately 30 minutes in the case of hand
saving state.
and day indicator alignment), crown
l Power Saving
operations will automatically become
● A time calibration signal is being received disabled. Push the crown back in to its normal
and the time setting is being adjusted. position and then pull it out again to re-enable
l Adjusting the Time Setting crown operations.
● Watch is connected with a phone to adjust l Using the Crown
its time setting.
l Connecting with a Phone to Adjust the
Watch’s Time

Q5 Hands are stopped and buttons do

not work.

The watch is in the charge recovery mode.

Wait until the recovery process is complete
(for about 15 minutes). The watch will recover
more quickly if you place it in a brightly lit
location.

Q6 Why is the current time indicated by

the watch is off by a certain amount
of time (nine hours, three hours and
15 minutes, etc.)?

The city setting is not correct. Select the

correct setting.
l Setting a Home City

Q7 The current time indicated by the

watch is off by one hour or 30
minutes.

The summer time setting is not correct. Select

the correct setting.
l Setting a Home City

Q8 The hand and/or day indicator are not

aligned correctly.

Strong magnetism or impact can cause the

hands and/or the indicator to go out of
alignment. Adjust hand and/or day indicator
alignment.
l Adjusting Hand and Day Indicator
Alignment
● Check the information below to find out how
to align the hands and/or day indicator
manually.
l Adjusting Hand and Day Indicator
Alignment

22