Ej080na 04C Cmimei

Download as pdf or txt
Download as pdf or txt
You are on page 1of 24

CHIMEI INNOLUX DISPLAY CORPORATION

LCD MODULE
S P E C I F I C AT I O N

Customer:
Model Name: EJ080NA-04C
Date: 2011/07/15
Version: 02

■ Preliminary Specification
□ Final Specification

For Customer ’s Acceptance

Approved by Comment

Approved by Review ed by Prepared by

James Yu
Hans Chen Charlie Chou David Lee

2011/07/15 2011/07/15 2011/07/15

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMEI INNOLUX
copyright 2004
All rights reserved,
Copying forbidden.

Record of Revision
Revise
Version Page Content
Date
Pre-Spec.01 2011/03/04 Initial Release.
Per-Spec.02 2011/07/15 8 Modify power sequence

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMEI INNOLUX
Contents

1. General Specifications ............................................................................................................ 1


2. Pin Assignment....................................................................................................................... 2
2.1. TFT LCD Panel Driving Section...................................................................................... 2
3. Operation Specifications ......................................................................................................... 5
3.1. Absolute Maximum Rating.............................................................................................. 5
3.1.1. Typical Operation Conditions.................................................................................. 6
3.1.2. Current Consumption ............................................................................................. 7
3.1.3. Backlight Driving Conditions ................................................................................... 7
3.2. Power Sequence ............................................................................................................ 8
3.3. Timing Characteristics .................................................................................................... 9
3.3.1. AC Electrical Characteristics .................................................................................. 9
3.3.2. Input Clock and Data Timing Diagram .................................................................... 9
3.3.3. DC Electrical Characteristics ................................................................................ 10
3.3.4. Timing................................................................................................................... 11
3.3.5. Data Input Format................................................................................................. 12
4. Optical Specifications............................................................................................................ 13
5. Reliability Test Items ............................................................................................................. 17
6. General Precautions ............................................................................................................. 18
6.1. Safety ........................................................................................................................... 18
6.2. Handling ....................................................................................................................... 18
6.3. Static Electricity ............................................................................................................ 18
6.4. Storage ......................................................................................................................... 18
6.5. Cleaning ....................................................................................................................... 18
7. Mechanical Drawing ............................................................................................................. 19
8. Package Drawing ................................................................................................................... 20
8.1 Package Material Table ................................................................................................ 20
8.2 Package Quantity ......................................................................................................... 20
8.3 Package Drawing ......................................................................................................... 21

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:1/21

1. General Specifications

No. Item Specification Remark

1 LCD size 8.0 inch(Diagonal)

2 Driver element a-Si TFT active matrix

3 Resolution 1024 × 3(RGB) × 768

4 Display mode Normally White, Transmissive

5 Dot pitch 0.05275(W) × 0.15825(H) mm

6 Active area 162.048(W) × 121.536(H) mm

7 Module size 183.0(W) × 141.0(H) × 3.4(D) mm Note 1

8 Surface treatment Hard coating

9 Color arrangement RGB-stripe

10 View Direction(Gray Inversion) 4:30 o’clock

11 Interface Digital

12 Backlight power consumption 1.674W (Typ.)

13 Panel power consumption 0.372W (Typ.)

14 Weight TBD

Note 1: Refer to Mechanical Drawing.

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:2/21

2. Pin Assignment

2.1. TFT LCD Panel Driving Section

FPC Connector is used for the module electronics interface. The recommended model is
FH12A-40S-0.5SH manufactured by Hirose.
Pin No. Symbol I/O Function Remark
1 VCOM P Common Voltage
2 VDD P Power Voltage for digital circuit
3 VDD P Power Voltage for digital circuit
4 NC --- No connection
5 Reset I Global reset pin
Standby mode, Normally pulled high
STBYB = “1”, normal operation
6 STBYB I
STBYB = “0”, timing controller, source
driver will turn off, all output are High-Z
7 GND P Ground
8 RXIN0- I - LVDS differential data input
9 RXIN0+ I + LVDS differential data input
10 GND P Ground
11 RXIN1- I - LVDS differential data input
12 RXIN1+ I + LVDS differential data input
13 GND P Ground
14 RXIN2- I - LVDS differential data input
15 RXIN2+ I + LVDS differential data input
16 GND P Ground
17 RXCLKIN- I - LVDS differential clock input
18 RXCLKIN+ I + LVDS differential clock input
19 GND P Ground
20 RXIN3- I - LVDS differential data input
21 RXIN3+ I + LVDS differential data input
22 GND P Ground
23 NC --- No connection

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:3/21
24 NC --- No connection
25 GND P Ground
26 NC --- No connection
27 DIMO O Backlight CABC controller signal output
28 SELB I 6bit/8bit mode select Note1
29 AVDD P Power for Analog Circuit
30 GND P Ground
31 LED- P LED Cathode
32 LED- P LED Cathode
33 L/R I Horizontal inversion Note3
34 U/D I Vertical inversion Note3
35 VGL P Gate OFF Voltage
36 CABCEN1 I CABC H/W enable Note2
37 CABCEN0 I CABC H/W enable Note2
38 VGH P Gate ON Voltage
39 LED+ P LED Anode
40 LED+ P LED Anode
I: input, O: output, P: Power
Note1: If LVDS input data is 6 bits ,SELB must be set to High;
If LVDS input data is 8 bits ,SELB must be set to Low.
Note2: When CABC_EN=”00”, CABC OFF.
When CABC_EN=”01”, user interface image.
When CABC_EN=”10”, still picture.
When CABC_EN=”11”, moving image.
When CABC off, don’t connect DIMO, else connect it to backlight.
Note3: When L/R=”0”, set right to left scan direction.
When L/R=”1”, set left to right scan direction.
When U/D=”0”, set top to bottom scan direction.
When U/D=”1”, set bottom to top scan direction.

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:4/21
Note: Definition of scanning direction.
Refer to the figure as below:

Up

Right
Left

Down

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:5/21

3. Operation Specifications

3.1. Absolute Maximum Rating

(GND=AVSS=0V, Note 1)
Values
Item Symbol Unit Remark
Min. Max.

VCC -0.3 5.0 V

AVDD 6.5 13.5 V

Power voltage VGH -0.3 42.0 V

VGL -20.0 0.3 V

VGH-VGL - 40.0 V

TOP -10 50 ℃
Operation Temperature
Storage Temperature
TST -20 60 ℃
each LED
LED Reverse Voltage VR - (5) V
Note 2
each
LED Forward Current IF - (35) mA
LED

Note 1: The absolute maximum rating values of this product are not allowed to be exceeded
at any times. Should a module be used with any of the absolute maximum ratings
exceeded, the characteristics of the module may not be recovered, or in an extreme
case, the module may be permanently destroyed.
Note 2: VR Conditions: Zener Diode 20mA

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:6/21
3.1.1. Typical Operation Conditions

(GND=AVSS=0V, Note 1)
Values
Item Symbol Unit Remark
Min. Typ. Max.

VCC 3.0 3.3 3.6 V Note 2

AVDD 11.3 11.5 11.7 V


Power voltage
VGH 21.7 22 22.3 V

VGL -7.3 -7 -6.7 V

Input signal voltage VCOM 2.3 (3.3) 4.3 V Note 3

Input logic high voltage VIH (0.7VCC) - (VCC) V


Note 4
Input logic low voltage VIL 0 - (0.3VCC) V

Note 1: Be sure to apply VCC and VGL to the LCD first, and then apply VGH.
Note 2: VCC setting should match the signals output voltage (refer to Note 3) of customer’s
system board .
Note 3 Typical VCOM is only a reference value. It must be optimized according to each
LCM. Please use VR and base on below application circuit..
Note 4: RESET,STBYB,SELB,L/R,U/D,CABCEN0,CABCEN1.

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:7/21
3.1.2. Current Consumption

(GND=AVSS=0V)
Values
Item Symbol Unit Remark
Min. Typ. Max.

IGH - (0.35) (1.0) mA VGH=22V

IGL - (0.35) (1.0) mA VGL=-7V


Current for Driver
ICC - (40) (60) mA VCC=3.3V

IAVDD - (20) (30) mA AVDD=11.5V

3.1.3. Backlight Driving Conditions

Values
Item Symbol Unit Remark
Min. Typ. Max.

Voltage for LED backlight VL (8.4) 9.3 (10.2) V Note 1

Current for LED backlight IL (170) 180 (190) mA

LED life time - 20,000 - - Hr Note 2

Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and
IL =180mA.

Note 2: The “LED life time” is defined as the module brightness decrease to 50% original
brightness at Ta=25℃ and IL =180mA. The LED lifetime could be decreased if
operating IL is lager than 180 mA.

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:8/21
3.2. Power Sequence

3.2.1. Power on:

<20ms

VDD <500us

STBYB >50us
>500us
RESET >35ms

LVDS
Signal Normal signal
<20ms

AVDD

VCOM >20us

VGL >40us

VGH >120ms

B/L

3.2.2. Power off:

VDD

STBYB

RESET >=0ms
LVDS
Signal Normal signal

AVDD

VCOM >100ms

VGL

>50ms
VGH >=0ms

B/L

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:9/21
3.3. Timing Characteristics

3.3.1. AC Electrical Characteristics

Values
Parameter Symbol Unit Remark
Min. Typ. Max.
Clock frequency RxFCLK 20 - 71 MHz
Input data skew margin TRSKM 500 - - ps
Clock high time TLVCH - 4/(7* RxFCLK) - ns
Clock low time TLVCL - 3/(7* RxFCLK) - ns

3.3.2. Input Clock and Data Timing Diagram

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:10/21
3.3.3. DC Electrical Characteristics

Parameter Symbol Values Unit Remark


Min. Typ. Max.
Differential input high
RxVTH - - +0.1 V
Threshold voltage
RXVCM=1.2V
Differential input low
RxVTL -0.1 - - V
Threshold voltage
Input voltage range
RxVIN 0 - 2.4 V
(singled-end)
Differential input common mode
RxVCM |VID|/2 - 2.4-|VID|/2 V
voltage
Differential voltage |VID| 0.2 - 0.6 V
Differential input leakage current RVxliz -10 - +10 uA

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:11/21
3.3.4. Timing

Values
Item Symbol Unit Remark
Min. Typ. Max.

Frame rate
Clock Frequency fclk 52 65 71 MHz
=60Hz

Horizontal display area thd 1024 DCLK

HS period time th 1114 1344 1400 DCLK

HS Blanking thb+thfp 90 320 376 DCLK

Vertical display area tvd 768 H

VS period time tv 778 806 845 H

VS Blanking tvb+tvfp 10 38 77 H

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:12/21
3.3.5. Data Input Format

6bit LVDS input

8bit LVDS input

Note: Support DE timing mode only, SYNC mode not supported.

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:13/21

4. Optical Specifications

Values
Item Symbol Condition Unit Remark
Min. Typ. Max.

θL Φ=180°(9 o’clock) 65 75 -

θR Φ=0°(3 o’clock) 65 75 -
Viewing angle
degree Note 1
(CR≥ 10)
θT Φ=90°(12 o’clock) 65 75 -

θB Φ=270°(6 o’clock) 65 75 -

TON - 6 12 msec Note 3


Response time
TOFF - 14 28 msec Note 3

Contrast ratio CR 600 700 - - Note 4

WX Normal 0.26 0.31 0.36 - Note 2


θ=Φ=0°
Color chromaticity Note 5
WY 0.28 0.33 0.38 - Note 6

Luminance L 200 250 - cd/m² Note 6


Luminance
YU 70 75 - % Note 7
uniformity

Test Conditions:
1. VCC=3.3V, IL=180mA (Backlight current), the ambient temperature is 25℃.
2. The test systems refer to Note 2.

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:14/21
Note 1: Definition of viewing angle range
Normal line
θ=Φ=0°

Φ=90°
12 o’clock direction

θL θR
θT
θB

Φ=180° Φ=0°

Active Area

Φ=270°
6 o’clock direction

Fig. 4-1 Definition of viewing angle

Note 2: Definition of optical measurement system.


The optical characteristics should be measured in dark room. After 30 minutes
operation, the optical properties are measured at the center point of the LCD screen.
(Response time is measured by Photo detector TOPCON BM-7, other items are
measured by BM-5A/Field of view: 1° /Height: 500mm.)

Photo detector Normal line


θ=Φ=0°

Φ=90°
12 o’clock direction
500mm

Φ=180° Φ=0°
Active Area

LCD Panel
Φ=270°
6 o’clock direction

Fig. 4-2 Optical measurement system setup

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:15/21
Note 3: Definition of Response time
The response time is defined as the LCD optical switching time interval between
“White” state and “Black” state. Rise time (TON) is the time between photo detector output
intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo
detector output intensity changed from 10% to 90%.
White (TFT OFF) Black (TFT ON) White (TFT OFF)
Photo detector output

100%
(Relative value)

90%

10%
0%
TON TOFF

Fig. 4-3 Definition of response time

Note 4: Definition of contrast ratio


Luminance measured when LCD on the " White" state
Contrast ratio (CR) =
Luminance measured when LCD on the " Black" state

Note 5: Definition of color chromaticity (CIE1931)


Color coordinates measured at center point of LCD.

Note 6: Definition of luminance:


Measured at the center area of the panel when LCD panel is driven at “white”
state. The LED driving condition is IL=180mA .

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:16/21

Note 7: Definition of Luminance Uniformity


Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).Every
measuring point is placed at the center of each measuring area.
B min
Luminance Uniformity (Yu) =
B max
L-------Active area length W----- Active area width

L
W/6

L/6 L/3 L/3


W/3
W

W/3

Fig. 4-4 Definition of measuring points

Bmax: The measured maximum luminance of all measurement position.


Bmin: The measured minimum luminance of all measurement position.

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:17/21

5. Reliability Test Items


(Note3)
Item Test Conditions Remark

High Temperature Storage Ta = 60℃ 240hrs Note 1,Note 4

Low Temperature Storage Ta = -20℃ 240hrs Note 1,Note 4

High Temperature Operation Ts = 50℃ 240hrs Note 2,Note 4

Low Temperature Operation Ta = -10℃ 240hrs Note 1,Note 4

Operate at High Temperature


+40℃, 90%RH 240hrs Note 4
and Humidity
-20℃/30 min ~ +60℃/30 min for a total 100
Thermal Shock cycles, Start with cold temperature and end Note 4
with high temperature.
Frequency range:10~55Hz
Stroke:1.5mm
Vibration Test Sweep:10Hz~55Hz~10Hz
2 hours for each direction of X. Y. Z.
(6 hours for total)

100G 6ms,±X, ±Y, ±Z 3 times for each


Mechanical Shock
direction
Random Vibration :
0.015G*G/Hz from 5-200HZ, -6dB/Octave
Package Vibration Test from 200-500HZ
2 hours for each direction of X. Y. Z.
(6 hours for total)
Height:60 cm
Package Drop Test
1 corner, 3 edges, 6 surfaces

Electro Static Discharge ± 2KV, Human Body Mode, 100pF/1500Ω


Note 1: Ta is the ambient temperature of samples.
Note 2: Ts is the temperature of panel’s surface.
Note 3: In the standard condition, there shall be no practical problem that may affect the
display function. After the reliability test, the product only guarantees operation,
but don’t guarantee all of the cosmetic specification.
Note 4: Before cosmetic and function test, the product must have enough recovery time,
at least 2 hours at room temperature.

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:18/21

6. General Precautions
6.1. Safety

Liquid crystal is poisonous. Do not put it in your mouth. If liquid crystal touches your
skin or clothes, wash it off immediately by using soap and water.

6.2. Handling

1. The LCD panel is plate glass. Do not subject the panel to mechanical shock or to
excessive force on its surface.
2. The polarizer attached to the display is easily damaged. Please handle it carefully
to avoid scratch or other damages.
3. To avoid contamination on the display surface, do not touch the module surface
with bare hands.
4. Keep a space so that the LCD panels do not touch other components.
5. Put cover board such as acrylic board on the surface of LCD panel to protect panel
from damages.
6. Transparent electrodes may be disconnected if you use the LCD panel under
environmental conditions where the condensation of dew occurs.
7. Do not leave module in direct sunlight to avoid malfunction of the ICs.

6.3. Static Electricity

1. Be sure to ground module before turning on power or operating module.


2. Do not apply voltage which exceeds the absolute maximum rating value.

6.4. Storage

1. Store the module in a dark room where must keep at 25±10℃ and 65%RH or less.
2. Do not store the module in surroundings containing organic solvent or corrosive
gas.
3. Store the module in an anti-electrostatic container or bag.

6.5. Cleaning

1. Do not wipe the polarizer with dry cloth. It might cause scratch.
2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals might
permanent damage to the polarizer.

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:19/21

7. Mechanical Drawing

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:20/21

8. Package Drawing

8.1 Package Material Table

Unit
Model
No. Item Dimensions(mm) Weight Quantity Remark
(Material)
(kg)
LCM
1 EJ080NA-04C 183.0 × 141.0 × 3.4 TBD 30pcs
Module
BC Corrugated
2 Partition 512 × 349 × 226 1.184 1set
paper
Corrugated B Corrugated
3 349 × 186 × 38 0.155 4pcs
Bar paper
Dust-Proof
4 PE 700 × 530 0.060 1pcs
Bag
5 A/S Bag PE 220.0 × 200.0 × 0.2 0.003 30pcs
Co rru ga t e d
6 Carton 530 × 355 × 255 1 . 1 00 1 p cs
pap e r
7 Total weight TBD

8.2 Package Quantity

Total LCM quantity in Carton: no. of Partition 2 Rows × quantity per Row 15 = 30

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.


CHIMIE INNOLUX Date :2011-07-15
Page:21/21

8.3 Package Drawing

The copyright belongs to CHIMEI INNOLUX. Any unauthorized use is prohibited.

You might also like