DOP 110WS - Cleaned

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

DOP-107WV / DOP-110WS COM2 Port DOP-107WV (Rear view)

MODE1 MODE2 MODE3


COM Port Pin COM2 COM3 COM2 COM3 COM2 COM3
RS-232 RS-485 RS-485 RS-485 RS-232 RS-422
1 D+ TXD+

DOP-103WQ High Color ‧Widescreen‧


User-Friendly HMI Products
2
3
RXD
TXD
RXD
TXD

DOP-107WV Delta Electronics Inc,


No.18, Xinglong Rd., Taoyuan City
4
5 GND
D+
GND
D+
GND
RXD+

DOP-110WS
6 D- TXD-
33068, Taiwan 7 RTS RTS
8 CTS CTS
Instruction Sheet 9 D- D- RXD-
Note 1: Blank means connection is not required.
(1) Preface
Thank you for purchasing DOP-107WV. This instruction sheet provides information about DOP-107WV.
Before using the product, please read through this manual carefully in order to ensure the correct use of (3) Part names
the product. In addition, please place this manual safely for quick reference whenever is needed. Please Power Input
A B COM2/ COM3
follow the rules below if you have not finished reading this manual yet. DOP-103WQ (Front view) (24AWG wire min.)

 Install the product in a clean and dry location free from corrosive and inflammable gases or liquids, C COM1 D Network Port (LAN)
indoor use only.
E USB Slave F USB Host
 Ensure that all wiring instructions and recommendations are followed.
 Ensure that HMI is correctly connected to the ground. The grounding method must comply with
the national electrical standard (Please refer to NFPA 70: National Electrical Code, 2005 Ed.
DOP-110WS (Front view)
 Do not modify the wiring or disassemble HMI interface when HMI is connected to the power.
 Do not touch the power supply during operation. Otherwise, it may cause electric shock.
 When HMI displays low power notification and requires battery changes, please contact local
distributors or DELTA customer service center for the replacement. Do not change batteries by
yourself.
 DOP-100 series can be used for industrial automation equipment. Please read through this
manual carefully and install the product according to the instructions in order to avoid danger.
 Cleaning method: Please use dry cloth to clean the product.
 The product should be used at an altitude below 2000 m.
 If the equipment is used in a manner not specified by the manufacturer, the protection provided by
the equipment may be impaired.
 For repairing and maintenance, please contact DELTA Electronics, Inc. Address: No.18, Xinglong
Rd., Taoyuan City, Taiwan. TEL: +886-3-3626301. A Touch Screen/Display
If you have any enquiry during operation, please contact our local distributors or Delta sales
representatives. The content of this instruction sheet may be revised without prior notice. Please consult
our distributors or download the latest version at http://www.delta.com.tw/ia. DOP-103WQ (Rear view)

A Touch Screen/Display
(2) Communication Port Pin Assignment
DOP-103WQ COM Port
DOP-110WS (Rear view)
MODE1 MODE2 MODE3
COM Port Pin
COM1 COM2 COM1 COM2 COM1 COM2
RS-232 RS-485 RS-485 RS-485 RS-232 RS-422
1 D+ TXD+
2 RXD RXD
3 TXD TXD
4 D+ D+ RXD+
5 GND GND GND
6 D- TXD-
7 RTS RTS A Power Input (24AWG wire min.) B COM1 C
8 CTS CTS C USB Slave D USB Host
9 D- D- RXD-
E Network Port(LAN)
DOP-107WV / DOP-110WS COM1 Port DOP-107WV (Front view)

MODE1
COM Port Pin Power Input
A B COM2/ COM3
RS-232 (24AWG wire min.)

1 C COM1 D Network Port (LAN)


2 RXD E USB Slave F USB Host
3 TXD
G SD Card
4
5 GND
6
7 RTS
8 CTS
9
A Touch Screen/Display
(4) Dimensions for Installation Installation Method: Model DOP-103WQ DOP-107WV DOP-110WS

DOP-103WQ Step 1: Step 2: Flash ROM 256 Mbytes


Put the waterproof gasket into HMI and then Place the fasteners into slots and tighten the
insert the HMI into the panel cutout. screws till reaching the panel cutouts. RAM 512 Mbytes
4-wire resistive touch screen
Touch Screen
> 10,000,000 operated
Buzzer Multi-Tone Frequency (2 K ~ 4 K Hz)/80 dB

(Note 2)
Ethernet Interface 10/100 Mbps Auto sensing (with built-in isolated power circuit )

1 USB Slave Ver 2.0


USB
1 USB Host Ver 2.0
SD N/A SD * 1
RS-232 (supports flow
COM1 RS-232 (supports flow control) (Note 2))
control) / RS-485(Note 2))
Serial
Communication
COM2 RS-422 / RS-485(Note 2) RS-232 (supports flow control) / RS-485(Note 2))
Port

COM3 N/A RS-422 / RS-485(Note 2))


Step 3: Step 4:
Function Keys N/A
Tighten the screws with torque less than 0.5N-M / For heat dissipation, please keep a minimum
0.7N-M to avoid damage to the plastic case. clearance of 60 mm on the rear of the HMI. Perpetual Calendar Built-in
DOP-107/DOP-110 Torque: 6.17 lb-inch (0.7N-M)
Cooling Method Natural cooling
o o o
Operation Temperature is 0 C to 50 C and Storage Temperature is -20 C to +60 C
o DOP-103 Torque: 4.41 lb-inch(0.5N-M)
CE / UL (Please use shielding Ethernet cable and the magnetic ring with filter of
Safety Approval
300 ohm/100 MHz)
DOP-107WV Waterproof Level of
IP65(Not be evaluated by UL)/NEMA4/ Type 4X indoor use only
Panel Display
+24 VDC (-15% ~ +15%) (with built-in isolated power supply unit)
Operation Voltage (Note2)
Supplied by Class 2 or SELV circuit (isolated from MAINS by double insulation)
Voltage Endurance 500 VAC for 1 minute (between charging (DC24V terminal) and FG terminals)
(Note
Power Consumption
2) 5.8W (Max) (Note 3) 8.4W (Max) (Note 3) 11W (Max) (Note 3)

Backup Battery 3V lithium battery CR2032 × 1


About 3 years or more at 25oC but subjects to the temperature and the conditions
Backup Battery Life
during usage.
o o
Operation Temperature 0 C ~ 50 C
o o
Storage Temperature -20 C ~ +60 C
o o
Operating Environment 10% ~ 90% RH [0 ~ 40 C], 10% ~ 55% RH [41 ~ 50 C]; Pollution degree: 2
Recommended wiring is as follows:
Vibration Resistance Conforms to IEC61131-2; Continuous: 5 Hz ~ 8.3 Hz 3.5 mm, 8.3 Hz ~ 150 Hz 1 G
Type Wire Gauge (AWG) Stripped length Torque
Solid 24 ~ 12 7 ~ 8 mm 5 kg-cm (4.3 lb-in) Shock Resistance Conforms to IEC60068-2-27: 11 ms, 15 G Peak , X, Y, Z direction for 6 times
Stranded 24 ~ 12 7 ~ 8 mm 5 kg-cm (4.3 lb-in)
Dimension
137 x 103 x 37.1 196 x 136 x 39 270 x 180.9 x 47.25
o o o o (W) x (H) x (D) mm
Operation Temperature is 0 C to 50 C and Storage Temperature is -20 C to +60 C
Be sure to perform wiring by referring to the following figure (power supply connector), wiring must Dimension for
be rated 75℃ min. Installation 118.8 x 92.8 186.8 x 126.8 255 x 170
DOP-110WS
(W) x (H) mm
Weight Approx.280g Approx. 560 g Approx. 1.1 Kgs

Note:
1. The half-life of backlight is defined as original luminance being reduced by 50% when the maximum
driving current is supplied to HMI. The life of LED backlight shown here is an estimated value under 25oC
normal temperature and humidity conditions.
2. The withstand voltage of the isolated power circuit is 1500 V peak for 1 minute.
3. Power consumption of HMI is the power consumed when not connecting to any peripheral devices. To
ensure normal operation of HMI, the recommended power supply is: power consumption x 1.5 ~ 2.
4. Isolated power supply is recommended.
5. DOPSoft, the program editor for DOP-100 series products and user manuals can be downloaded at
our website. In addition, the content of this instruction sheet may be revised without prior notice.
Please consult our distributors or download the latest version at http://www.delta.com.tw/ia.
6. DOP-100 series can be used for industrial automation equipment. Please read through this manual
carefully and install the product according to the instructions to avoid danger.

o o o o
Operation Temperature is 0 C to 50 C and Storage Temperature is -20 C to +60 C
(6) Specifications
Model DOP-103WQ DOP-107WV DOP-110WS
(5) Installation and Wiring
4.3" TFT LCD 7" TFT LCD 10.1" TFT LCD
Installation Notes: Display Type
(65535 colors) (65535 colors) (65535 colors)
 Improper installation will result in malfunction and greatly reduce the life of the HMI. Be sure to Resolution 480 x 272 pixels 800 x 480 pixels 1024 x 600 pixels
follow the guidelines in this quick start when installing the HMI.
 In order to ensure the HMI being well ventilated, make sure that the ventilation holes are not LCD LED Back Light (less than LED Back Light (less than LED Back Light (less than
Module Backlight 10,000 hours half-life at 20,000 hours half-life at 30,000 hours half-life at 25
obstructed and provide sufficient clearance for the HMI.
 To protect the panel, be sure to install a waterproof gasket into HMI. 25oC) (Note 1) 25oC) (Note 1) o
C) (Note 1)
 For use on a flat surface of a Type 4X "Indoor Use Only" enclosure or equivalent. If Enclosure with Display Size 95.04 x 53.856 mm 154.08 x 85.92 mm 225.52 x 128.10 mm
lower type rating will cause de-rating.
Brightness 400 cd/m² (Typ.) 450 cd/m² (Typ.) 450 cd/m² (Typ.)
 The allowable thickness of the panel for mounting should be less than 5 mm.
CPU ARM Cortex-A8 (800MHz)

You might also like