A 45

FILE NO.
050-200505 (MFRS VERSION A)
SERVICE MANUAL
COLOR TELEVISION
27A45 27A45C
DOCUMENT CREATED IN JAPAN, February, 2005
SERVICING NOTICES ON CHECKING

1. KEEP THE NOTICES
As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual.
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
2. AVOID AN ELECTRIC SHOCK

There is a high voltage part inside. Avoid an electric shock while the electric current is flowing.
3. USE THE DESIGNATED PARTS

The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used.
7. PERFORM A SAFETY CHECK AFTER SERVICING

Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE

In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal Headphone jack
HOW TO ORDER PARTS

Please include the following informations when you order parts. (Particularly the VERSION LETTER.) 1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. 2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL.
IMPORTANT
When you exchange IC and Transistor with a heat sink, apply silicon grease on the contact section of the heat sink. Befor applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.)
A1-1
27A45/27A45C
ABOUT LEAD FREE SOLDER (PbF)

Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a PbF printing on the PCB. (Please refer to figures.)
Caution: Pb free solder has a higher melting point than standard solder;
Typically the melting point is 50F~70F(30C~40C) higher. Please use a soldering iron with temperature control and adjust it to 650F 20F (350C 10C).
In case of using high temperature soldering iron, please be carefull not to heat too long. Pb free solder will tend to splash when heated too high (about 1100F/ 600C). All products with the printed circuit board with PbF printing must be serviced with lead free solder. When soldering or unsoldering, completely remove all of the solder from the pins or solder area, and be sure to heat the soldering points with the lead free solder until it melts sufficiently.
Recommendations
Recommended lead free solder composition is Sn-3.0Ag-0.5Cu.
A1-2
27A45/27A45C
TABLE OF CONTENTS
SERVICING NOTICES ON CHECKING ..................................................................................... HOW TO ORDER PARTS .......................................................................................................... IMPORTANT ............................................................................................................................... ABOUT LEAD FREE SOLDER (PbF) ......................................................................................... TABLE OF CONTENTS .............................................................................................................. GENERAL SPECIFICATIONS ................................................................................................... DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ............................................................................................... 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................ SERVICE MODE LIST ................................................................................................................ CONFIRMATION OF HOURS USED ......................................................................................... WHEN REPLACING EEPROM (MEMORY) IC .......................................................................... ELECTRICAL ADJUSTMENTS .................................................................................................. BLOCK DIAGRAMS ................................................................................................................... PRINTED CIRCUIT BOARDS MAIN/CRT ................................................................................................................................ SCHEMATIC DIAGRAMS MICON ..................................................................................................................................... CHROMA ................................................................................................................................. DEFLECTION .......................................................................................................................... POWER ................................................................................................................................... SOUND .................................................................................................................................... TUNER/STEREO ..................................................................................................................... AV ............................................................................................................................................ CRT .......................................................................................................................................... COMB/FILTER ......................................................................................................................... WAVEFORMS ............................................................................................................................. MECHANICAL EXPLODED VIEWS ........................................................................................... MECHANICAL REPLACEMENT PARTS LIST ......................................................................... ELECTRICAL REPLACEMENT PARTS LIST ........................................................................... A1-1 A1-1 A1-1 A1-2 A2-1 A3-1~A3-10 B1-1 B2-1, B2-2 C1-1 C1-1 C1-1 D-1~D-6 E-1, E-2 F-1~F-4 G-1, G-2 G-3, G-4 G-5, G-6 G-7, G-8 G-9, G-10 G-11, G-12 G-13, G-14 G-15, G-16 G-17, G-18 H-1, H-2 I-1~I-4 J1-1, J1-2 J2-1~J2-8
A2-1
27A45/27A45C
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Magnetic Field BV/BH 27 inch / 676mmV Normal +0.45G/0.18G NTSC 2Speaker Front 2.0 x 3.5 Inch 8 ohm 2.5 + 2.5 W W No US System M 1Tuner USA(W/ CATV) 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz at AC Stand by (at AC) Per Year Power Fuse Safety Circuit IC Protector(Micro Fuse) Safety Radiation X-Radiation Operation Storage 125 W at AC 120 V 60 Hz 3 W at AC 120 V 60 Hz -kWh/Year Yes Yes No UL FCC DHHS +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH
Color System Speaker Position Size Impedance MAX 10%(Typical)
Sound Output NTSC3.58+4.43 /PAL60Hz Broadcasting System Tuner and Receive CH
G-2
Tuning System
System Destination CH Coverage Picture(FP) Sound(FS) FP-FS
Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Power Consumption
G-3
Power
AC DC
Protector
G-4
Regulation
G-5 G-6
Temperature Operating Humidity
A3-1
27A45
G-7 On Screen Display Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off Surround On/Off Set Up TV/CABLE(CATV) CH Program Add/Erase Option Language V-chip CH Label Favorite CH Lock On/Off Timer Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Game Timer Sleep Timer Sound Mute V-chip Rating 16: 9 G-8 G-9 OSD Language Clock and Timer Sleep Timer Max Time Step Program(On Timer / Off Timer / Clock) more than Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes English No French Spanish
On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode)
120 Min 10 Min Yes -No Min Sec
A3-2
27A45
G-10 Remote Control Unit Glow in Dark Remocon Format Remocon Format Custom Code Power Source Total Keys Keys RC-GW Yes Toshiba Toshiba TV:40-BF h 3V UM-4 x 2 pcs 49 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
Voltage(D.C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down TV/Caption/Text CH1/CH2 TV/Video(TV/AV) CH RTN/CH ENT(Quick View) Sleep RE Call(Call) Reset Menu/Enter Mute Exit MTS(Audio Select) Fav.Up Fav.Down 16: 9 CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) FF Rew Rec Play Stop TV VCR Cable DVD CODE Volume Up(DVD) Volume Down(DVD) DVD CLEAR TOP MENU DVD MENU DISPLAY
Multi Brand Keys
A3-3
27A45
G-11 Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search CH Allocation SAP Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect CH Lock Video Lock Game Timer (Max Time:120 Min) Energy Star Favorite CH Surround 16:9 Mode 2 Tuner P-in-P Owner's Manual Language W/ Warranty Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) ESP Card PTB Sheet 300 ohm to 75 ohm Antenna Adapter Yes Yes No Yes No No Yes Yes Yes USA,Toshiba Type No No No Yes No Yes No No No Yes 3 Lines Yes No Yes Yes Yes Yes Yes Yes No Yes Yes No No English / Spanish Yes Yes No
G-12
Accessories
No No No No No No No No No No No No Yes UM4 size x 2 No No No Yes No No No
A3-4
27A45
G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down AC/DC TV/CATV Selector Degauss Main Power SW Power Stand-by On Timer Video Input Audio Input Other Terminal Video Input(Rear1) Video Input(Rear2) Audio Input(Rear1) Audio Input(Rear2) Video Output Audio Output S- Input Euro Scart Color Stream Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Content Material Dimensions W x D x H(mm) Description of Origin Material Dimensions W x D x H(mm) Design Description of Origin Yes No No No Yes Yes Yes Yes No No No No Yes(RED) No No RCA RCA x 2 No RCA RCA RCA x 2 RCA x 2 RCA RCA x 2 Yes No RCA x 3 No No No F Type No 740 x 491.5 x 571.5 37.0kg ( 81.6 lbs) 41.0Kg ( 90.4 lbs) No ---Sets -/--- x -- x -No Double/Brown 850 x 575 x 665 As per Buyer's Yes Natural Dropping At 1 Corner / 2 Edges / 4 Surfaces 60 (ORION SPEC:31) 168 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No Yes Yes Yes
Rear
Indicator
Terminals
Front
Rear
G-14 G-15 G-16
Set Size Weight Carton Master Carton
Gift Box
Drop Test Height (cm) Container Stuffing Cabinet Cabinet Front Cabinet Rear PCB Non-Halogen Demand Eyelet Demand Pb-free Soldering Parts Specificat
G-17
Cabinet Material
G-18
Environment
A3-5
27A45
G-1 TV System CRT CRT Size / Visual Size CRT Type Magnetic Field BV/BH 27 inch / 676mmV Normal +0.45G/0.18G NTSC 2Speaker Front 2.0 x 3.5 Inch 8 ohm 2.5 + 2.5 W W No US System M 1Tuner USA(W/ CATV) 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz at AC Stand by (at AC) Per Year Power Fuse Safety Circuit IC Protector(Micro Fuse) Safety Radiation X-Radiation Operation Storage 125 W at AC 120 V 60 Hz 3 W at AC 120 V 60 Hz -kWh/Year Yes Yes No CSA IC HWC +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH
Color System Speaker Position Size Impedance MAX 10%(Typical)
Sound Output NTSC3.58+4.43 /PAL60Hz Broadcasting System Tuner and Receive CH
G-2
Tuning System
System Destination CH Coverage Picture(FP) Sound(FS) FP-FS
Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Power Consumption
G-3
Power
AC DC
Protector
G-4
Regulation
G-5 G-6
Temperature Operating Humidity
A3-6
27A45C
G-7 On Screen Display Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off Surround On/Off Set Up TV/CABLE(CATV) CH Program Add/Erase Option Language V-chip CH Label Favorite CH Lock On/Off Timer Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Game Timer Sleep Timer Sound Mute V-chip Rating 16: 9 G-8 G-9 OSD Language Clock and Timer Sleep Timer Max Time Step Program(On Timer / Off Timer / Clock) more than Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes No No French
English
Spanish
On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode)
120 Min 10 Min Yes -No Min Sec
A3-7
27A45C
G-10 Remote Control Unit Glow in Dark Remocon Format Remocon Format Custom Code Power Source Total Keys Keys RC-GW Yes Toshiba Toshiba TV:40-BF h 3V UM-4 x 2 pcs 49 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
Voltage(D.C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down TV/Caption/Text CH1/CH2 TV/Video(TV/AV) CH RTN/CH ENT(Quick View) Sleep RE Call(Call) Reset Menu/Enter Mute Exit MTS(Audio Select) Fav.Up Fav.Down 16: 9 CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) FF Rew Rec Play Stop TV VCR Cable DVD CODE Volume Up(DVD) Volume Down(DVD) DVD CLEAR TOP MENU DVD MENU DISPLAY
Multi Brand Keys
A3-8
27A45C
G-11 Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search CH Allocation SAP Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect CH Lock Video Lock Game Timer (Max Time:120 Min) Energy Star Favorite CH Surround 16:9 Mode 2 Tuner P-in-P Owner's Manual Language W/ Warranty Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) ESP Card PTB Sheet 300 ohm to 75 ohm Antenna Adapter Yes Yes No Yes No No Yes Yes No - Type No No No Yes No Yes No No No Yes 3 Lines Yes No Yes Yes Yes Yes Yes Yes No Yes Yes No No English /French Yes Yes No
G-12
Accessories
No No No No No No No No No No No No Yes UM4 size x 2 No No No No No No No
A3-9
27A45C
G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down AC/DC TV/CATV Selector Degauss Main Power SW Power Stand-by On Timer Video Input Audio Input Other Terminal Video Input(Rear1) Video Input(Rear2) Audio Input(Rear1) Audio Input(Rear2) Video Output Audio Output S- Input Euro Scart Color Stream Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Content Material Dimensions W x D x H(mm) Description of Origin Material Dimensions W x D x H(mm) Design Description of Origin Yes No No No Yes Yes Yes Yes No No No No Yes(RED) No No RCA RCA x 2 No RCA RCA RCA x 2 RCA x 2 RCA RCA x 2 Yes No RCA x 3 No No No F Type No 740 x 491.5 x 571.5 37.0kg ( 81.6 lbs) 41.0Kg ( 90.4 lbs) No ---Sets -/--- x -- x -No Double/Brown 850 x 575 x 665 As per Buyer's Yes Natural Dropping At 1 Corner / 2 Edges / 4 Surfaces 60 (ORION SPEC:31) 168 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No Yes Yes Yes
Rear
Indicator
Terminals
Front
Rear
G-14 G-15 G-16
Set Size Weight Carton Master Carton
Gift Box
Drop Test Height (cm) Container Stuffing Cabinet Cabinet Front Cabinet Rear PCB Non-Halogen Demand Eyelet Demand Pb-free Soldering Parts Specificat
G-17
Cabinet Material
G-18
Environment
A3-10
27A45C
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)
Fig. 1-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver
CRT Support Alligator Clip Fig. 1-4
GND on the CRT
Fig. 1-1 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap
CRT CRT Support Fig. 1-2
Support Fig. 1-5
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts. B1-1 27A45/27A45C
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
Masking Tape (Cotton Tape)
IC
Tweezers
Fig. 2-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) NOTE Do not rotate or move the IC back and forth , until IC can move back and forth easily after desoldering the leads completely. 4. Peel off the Masking Tape.
Fig. 2-3
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Blower type IC desoldering machine
Braided Shield Wire
Soldering Iron
IC
Fig. 2-2
IC pattern
Fig. 2-4
B2-1
27A45/27A45C
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Soldering Iron. (Refer to Fig. 2-8.)
Thin-tip Soldering Iron
IC
Soldering Iron
Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, always be sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
Solder
Soldering Iron
IC
Supply soldering from upper position to lower position
Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Braided Shield Wire
Fig. 2-7 B2-2 27A45/27A45C
SERVICE MODE LIST

This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 2 seconds. Set Key VOL. (-) MIN Remocon Key 0 Releasing of V-CHIP PASSWORD. Initialization of factory data. NOTE: Do not use this for normal servicing. If you set factory initialization, the memories are reset such as the channel setting, and the POWER ON total hours. POWER ON total hours is displayed on the screen. Refer to the "CONFIRMATION OF HOURS USED". VOL. (-) MIN 6 Can be checked of the INITIAL DATA of MEMORY IC. Refer to the "WHEN REPLACING EEPROM (MEMORY) IC". VOL. (-) MIN 9 Display of the Adjustment MENU on the screen. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment). Operations
VOL. (-) MIN
CONFIRMATION OF HOURS USED

POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set factory initialization, the total hours is reset to "0". ADDRESS DATA 1. Set the VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds. Initial setting content of MEMORY IC. INIT 00 90 3. After the confirmation of using hours, turn off the power. POWER ON total hours. CRT ON 0010
= (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
FIG. 1
WHEN REPLACING EEPROM (MEMORY) IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: No need to set data after position INI 1F due to the adjustment value. INI 00 10 +0 90 50 +1 E8 00 +2 02 00 +3 65 00 +4 5E 01 +5 B3 00 +6 24 00 +7 37 99 +8 *1 3F +9 AC 0F +A 0B 0D +B 04 E6 +C 40 A8 +D 40 21 +E 40 42 +F 7F 00 *1 INI 08 USA 39 CANADA 38
Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using VOL. +/- button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn POWER on. 10. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds. 11. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC.
C-1
27A45/27A45C
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION Use an isolation transformer when performing any service on this chassis. Before removing the anode cap, discharge electricity because it contains high voltage. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. When you exchange IC and Transistor with a heat sink, apply silicon grease on the contact section of the heat sink. Befor applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.)
2. BASIC ADJUSTMENTS
2-1: CONSTANT VOLTAGE 1. Place the set in AV MODE without signal. 2. Connect the digital voltmeter to the TP003. 3. Adjust the VR502 until the digital voltmeter is 123 0.5V. 2-2: CUT OFF 1. Place the set in Aging Test for more than 15 minutes. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select CUT OFF. 4. Adjust the Screen Volume until a dim raster is obtained. 2-3: WHITE BALANCE, WHITE BALANCE CS NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set in Aging Test for more than 15 minutes. 2. Receive the gray scale pattern from the Pattern Generator with Brust On. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (12) on the remote control to select R. BIAS. 5. Press the CH. UP/DOWN button on the remote control to select the R. BIAS, G. BIAS, B. BIAS, B. DRIVE or R. DRIVE. 6. Adjust the VOL. UP/DOWN button on the remote control to whiten the R. BIAS, G. BIAS, B. BIAS, B. DRIVE and R. DRIVE at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is achieved. 8. Press the TV/VIDEO button on the remote control to set to the CS mode. 9. Receive the gray scale pattern from the Pattern Generator with Brust On. 10. If the picture is too much green.Activate the adjustment mode display of Fig. 1-1 and press the channel button (28) on the remote control to select CB PED. 11. Adjust the VOL. UP/DOWN button on the remote control to select the step up. 12. If the picture is too much red.Activate the adjustment mode display of Fig. 1-1 and press the channel button (29) on the remote control to select CR PED. 13. Adjust the VOL. UP/DOWN button on the remote control to select the step down. 2-4: FOCUS 1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct.
Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. Multi-sound Generator 4. Pattern Generator On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 2 second to appear the adjustment mode on the screen as shown in Fig. 1-1.
TV
00 OSD
35 Fig. 1-1
2. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 3. Press the MENU button on the remote control to end the adjustments.
NO. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 FUNCTION OSD H CUT OFF H. VCO H. PHASE AFC GAIN V. SHIFT H. SIZE V. SIZE V. LINERITY VS CORRECTION R DRIVE B DRIVE R CUT OFF G CUT OFF B CUT OFF BRIGHT MAX BRIGHT CENT BRIGHT MIN CONTRAST MAX NO. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 88 FUNCTION CONTRAST CENT CONTRAST MIN COLOR MAX COLOR CENTER COLOR MIN TINT SHARPNESS Cb DELAY FINE Cr DELAY FINE Cb PEDESTAL ADJ Cr PEDESTAL ADJ PARABOLA CORNER TRAPWZIUM LEVEL SEPARATION1 SEPARATION2 READ DATA
Fig. 1-2 D-1 27A45/27A45C
2-5: HORIZONTAL SIZE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select H. SIZE. 4. Press the VOL. UP/DOWN button on the remote control adjust the H.SIZE becomes 10 4%. 2-6: VERTICAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Adjust the VR401 until the horizontal line becomes fit to the notch of the shadow mask. horizontal line 2-10: PARABOLA CORR 1. Receive the cross hatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (30) on the remote control to select PARABOLA. 4. Press the VOL. UP/DOWN button on the remote control until the right and left vertical lines are straight. 2-11: LEVEL 1. Connect the AC voltmeter to pin 6 of CP101. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (33) on the remote control to select LEVEL. 3. Press the VOL. UP/DOWN button on the remote control until the AC voltmeter is 75 2mV. 2-12: SEPARATION 1, 2 Please do the method (1) or method (2) adjustment. Method (1) 1. Set the multi-sound signal generator for each different Lch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz) and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select SEP 1. 4. Press the VOL. UP/DOWN button on the remote control to adjust it until the audio output wave becomes a fine sine wave. 5. Press the CH UP button once the set to SEP 2 mode. Then perform the above adjustment 4. 2-9: TRAPEZIUM 1. Receive the cross hatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (32) on the remote control to select TRAPEZIUM. 4. Press the VOL. UP/DOWN button on the remote control until the both vertical lines of the screen become paralled.
;; ;; ;; ; ;; ;; ;; ;;
Notch
Shadow mask Fig. 2-1 2-7: VERTICAL SIZE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select V. SIZE. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 9 2%. 2-8: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-7. After the adjustment of Vertical Linearity, reconfirm the Vertical Position and Vertical Size adjustments. 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness, contrast, to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (08) on the remote control to select V. LIN. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum.
D-2
27A45/27A45C
Method (2) 1. Set the multi-sound signal generator L-ch=1KHz, R-ch =Non input and receive the RF. 2. Connect the oscilloscope to the Audio Out Jack (R-ch). 3. Press the AUDIO SELECT button on the remote control to set to the stereo mode. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select SEP 1. 5. Press the VOL. UP/DOWN button on the remote control to adjust it until the R-ch output becomes minimum. 6. Set the multi-sound signal generator L-ch=Non input, R-ch=1KHz and receive the RF. 7. Connect the oscilloscope to the Audio Out Jack (L-ch). 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (35) on the remote control to select SEP 2. 9. Press the VOL. UP/DOWN button on the remote control to adjust it until the L-ch output becomes minimum. The output difference of the between with Filter and without Filter should be more than 25db for both L and R. 2-13: OSD POSITION 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-2) 2-15: COLOR CENT 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP022. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "COLOR CENT". 5. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales on the screen of the oscilloscope. 6. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 120 10% of the white level. (Refer to Fig. 2-3) 7. Receive the video color bar pattern. (Audio Video Input) 8. Set to the AV mode. Then perform the above adjustments 2~6. 9. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 2~4. 10.Press the VOL. UP/DOWN button on the remote control until the color step No. becomes "65".
100% 120%
TV
Fig. 2-3 00 OSD A 2-14: BRIGHT CENT 1. Receive the monoscope pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI CENT". 4. Press the VOL. UP/DOWN button on the remote control until the white 0% is starting to be visible. 5. Receive the monoscope pattern. (Audio Video Input) 6. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. 7. Press the TV/VIDEO button on the remote control to set to the CS mode. 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI CENT". 9. Press the VOL. UP/DOWN button on the remote control until the brightness step No. becomes "65". D-3 27A45/27A45C 35 B
Fig. 2-2
2-16: TINT 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP024. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (24) on the remote control to select "TINT". 5. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes as straight line. (Refer to Fig. 2-4) 6. Receive the video color bar pattern. (Audio Video Input) 7. Set to the AV mode. Then perform the above adjustments 2~5. 8. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 2~4. 9. Press the VOL. UP/DOWN button on the remote control until the tint step No. becomes "55". 2-19: Confirmation of Fixed Value (Step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 02 04 05 09 15 17 19 20 21 23 25 26 27 28 29 31 FUNCTION H.VCO AFC GAIN V.SHIFT VS.CORRECTION BRI.MAX BRI.MIN CONT.CENT CONT.MIN COL.MAX COL.MIN SHARPNESS CB DL CR DL CB PED CR PED CORNER RF AV 03 03 04 04 02 02 38 38 140 140 45 45 64 64 20 20 90 90 00 00 40 40 00 00 00 00 08 08 08 08 35 35 CS 03 04 02 38 140 45 64 20 90 00 40 00 00 08 08 35
"A"
Fig. 2-4 2-17: CONTRAST MAX 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select CONT. MAX. 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes 85. 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 5. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 1~3. 2-18: HORIZONTAL PHASE 1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select H.PHASE. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum.
D-4
27A45/27A45C
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar genera2. tor. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends 3. are equally wide. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen 4. is green. 5. Confirm red and blue color. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB
R G B UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT Fig. 3-2-a
R G B
WEDGE
WEDGE
WEDGE WEDGE POSITION Fig. 3-2-b
PURITY MAGNETS 6 POLE MAGNETS 4 POLE MAGNETS Fig. 3-1
D-5
27A45/27A45C
4. ELECTRCAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CRT PCB
CP806
TP024 TP022 R805 R803
J801
CP803
CP802B
CP801B
CD801 CRT CD802
CP801A CP101
FB401 CP401 TP003 W003 TU001 VR502 VR401
CRT AC IN
CP501 CP1001
CD501
SPEAKER CP802A L503 CP502 CRT
MAIN PCB
D-6
27A45/27A45C
BLOCK DIAGRAM
A/V OUT J708

6
4 2
COMB FILTER IC IC1501 LA76605M-TLM

18 C OUT 16 Y OUT Y IN 3 AMP
Q603, Q614, Q605
CHROMA IC IC601 M61283FP R70T

60 VIDEO LINE OUT
Q802, Q806
FB401
J801
1 F
7
VIDEO SW(Y) IC IC1502 MM1501XNRE S-JACK J702 LINE1(REAR) J701

6 3 2 3 4 6 Vin1 V.OUT 4 Vin2 2
B OUT 16
BLUE OUT
Q803, Q805
11
F S
HV
51 Y IN(Y/C)
G OUT 15
GREEN/RED OUT
Q801, Q804
VIDEO SW(C) IC IC1503 MM1501XNRE

6 Vin1 V.OUT 4 Vin2 2
R OUT 14
RED/GREEN OUT
CRT V801
V-OUT IC IC401 LA78041
1
49 C IN(Y/C)
V OUT
63
Q402 Q405 H.OUT
DY
FRONT -VIDEO J705
46 42
CVBS1 CVBS2 CVBS3
H OUT
H.DRIVER
6 3 2
5
38
MICON IC101 OEC7090B
OS101
1 D109
53 CVBS4 48 Y IN(YUV) 44 U IN(YUV) 40 V IN(YUV)
R IN 23 G IN 22 B IN 21
FAST BLK 24
34 RED R 35 GREEN G 36 BLUE B 33 BLANK
REMOCON 9
LINE2(REAR) J703
ON_TIMER 10 X.IN 19 X.OUT 20 KEY1 6 KEY2 7

X101 8MHz
3 2
POWER VOL DOWN CH DOWN VOL UP CH UP
TU001 YUV_IN(REAR) J704

11 10 26 SDA
XTAL 3.58 34
X602 3.97545MHz
30 SCL1 31 SDA1
27 SCL SOUND DECORDER IC IC902 AN5829S 14 24 5 SDA 6 SCL
AUDIO SW(L) IC IC702 MM1501XNRE

6 Vin1 4 Vin2 V.OUT 2
17 13
FRONT-AUDIO.R J707
2
MEMORY IC IC199 BR24L16FJ-WE2
FRONT-AUDIO.L J706
2 3 18
19
AUDIO SW(R) IC IC701 MM1501XNRE

6 Vin1 V.OUT 2 4 Vin2 Q901 BUFFER Q902 BUFFER 23
21 22
3 30
16 19
2 5
12 7 SPEAKER SP1001
TONE CONTROL IC IC302 AN5891SA-E1V
SOUND AMP IC IC1001 AN17808B
E-1
27A45/27A45C
E-2
TP003
TP004
W002
D404 D501 HS501 C503_1 CP501 R542 D504 C513_1 F501 C502_1 TH501_1 CP507 FH501
R500
C5
08
_1
R430 W001 C415 W003 D503 CP502 CP508 R541_1 Q514 D507 R432 R501
R544 C507 RY501 C506_1 R502 D523 W801 L501 B501 T501 R540 R539 C505_1 C512 W004 R520 FH502
Q502
FB401
W005
D502
R443
R438
R543_1
C519
R508 W802 Q806 R807 D509 D506 D525 Q802 R547 R803 OS101 R805 D803
_1
IC504
C524
CP801B D810 D812
C509
D508
W007 D528 VR502 Q507 R506 Q801 D802 D520 Q805 R120 W016 CP806_1 R102 R806 D801 W009 W010
D4 09
Q804
R510
R802 C108 D109
W013
W011
D407
_1 12 C4
W817 R554 R553 D408_1 W863 D517 D512 C520 D511 C802 Q504 R824 W015 Q803 B504 CP802B W825 W012 D811
C426
W006
C421_1
D405
C521_1
B403
CP803
D505
CCD010A
C801
D514
R507_1
CP801A
PRINTED CIRCUIT BOARDS MAIN/CRT (INSERTED PARTS)
Q405
D411
R546
C413_1
Q503
R505
C425_1
C517
D510
R524
R434
C527 C501 W042 W043 C523 SW101
R536 C504 R512 R503 W806 W056 Q509 C539 Q512 W033 W039 D406 C139 W035 W032 W037 W038 W040 R132 W029 R001 Q402 R002 C401 W024 W044 W041 W030 W097 W103 W048 W094 W091 W046 W045 W805 W106 W107 W108 W112 W114 W099 W111 W080 C645 S810Y W098 W083 C630 C621 W186 W074 W070 W073 W072 W183 W068 W067 W187 W090 W089 W088 C627 W087 C618 C642 Q607 C605 W115 D602 C622 R702 R709_1 W130 R616 Q604 C609_1 Q602 W139 W082 D104 W811 R130 R124 C110 C122 W028 S810X C109 Q508 CP401 HS402 C409 D410
SOLDER SIDE
C427_1
W055
L40
R515
R133
W021
W827
W019 R537 D403 IC401 W828 L402_1 R459_2 C442 W020 R433 T401 R437 C422_2 C430 C417_1 R413 C407 D402 C406 R410_1 R455_2 W836 C408 D415 D419 Q408 D416 D417 W027 R429 R421 R441 R422 R427 W018 D608 HS401 W185 W071 TP006 R436 W084 W026 W025 Q409 W022 W081 TP005 Q410 VR401_1 R418 W017 C402 R406 R414 W823 B405 D414 W023
R428
R535
R527 C550 R426
W052 W054 W822 D106
C403
D113 X101_1 W053 C113 R146
CMD016A
W861
CP101
R118
R140
W065
R139 W128 R119 W129 W126
W123 W120 W121 W118
R419 R457 R517_1 D513 W086 W085 W844
R456
J708
C728 R710
W078
W057
W064 D701 D703 C711 C707 J704
W075
D702
W058
W077 W076
C919 W829 W830
W061 W060
W079
W069
W096 C611 C629 C646 W184 D606 D605 W110 W170 Q606 D601 C615 Q601 R603 C603 C608 C606 W169 R626 CP802A W157 W167 R623 R902 R901 W092 R904 C902 W095 C901
C914 C910 C903
W119
X602
W104 W113 W109 W101 C638 W102 W100 D607
W125
L901
C907 C916 C905 C904
J703
W063 R701 C710 C708 W059 W062 C705 D705
C156_1
W093
D105 W116
SW103
SW104
W174 W176 W180
W117 W175 R905 R302
J701
D704
C306 R1009 W155 W150 W803 W151 C1008_1 R1014 W154 C610 R648 W144 W140 W173 Q611 C602 C304 D604 W172 C333 W815 W189 W142
1 1_ 60 R
C302 L301 R301 C305 C317 L1512 W141 W165 C308
C733 W135 J702 C701 W819 W820 W134
W132
W131
C1003
C1004
D709 C702 C001_1 W812 D001
C1009 IC1001 C1005 HS1001 C1002 W858 C1011_1 W136 W137 W835 C1001 S809X
W147 W148 W149
W143
C321 W168
R649
C318 W164 W163 W166 C1518 C1520 L1501 L1508 C1532 W146 W145 C1535 C1528 W848 C1510 C1530_1 W162 W831 W160 W177 W178 C1501 L1503 L1502 W834 S809Y C314
R6
W181
02
C1502 C319
R304 R303 CP1001 J707
TU001
W133
L1510
W138
W156
L1511 L1505
W161 C1525
W832
C316
W179 W833
J706
J705
D706
F-1
R4 52
W008
C114
W049
SW102
J8
C418
01
_1
C420_1
Q505
R804
SW105
D524 R545
D516
27A45/27A45C
- REPLACE AS MARKED . RISK OF FIRE
C5 35
F-2
R4 39
R907
C737 R734
C640 R1523 IC702 R609 R1013 R705 Q709
C706 C724 C727 R726 C722 C736
C719
IC701
Q1001
R729 R733 C725 C738 R739
R706
R605 C607 R1015
C734 R735 R1004 C005
C1010 R1010 R1011 C1012 R1003
Q1504
IC1501
C1523 IC1502
C1515 R1509
R1506 C1513 C1517 R1530 C1531 R1505 C1509 IC1503 Q1503 R1507 C002 R006 C1519
Q1508
C1521
1 60 IC
F-3
R404 R810 C541 R532 R533 R801 C554 C511
CCD010A
R811 R815 C809 R819 R813 R821 R809 R812 R817 C811 R820 R814
R808
Q101
R818 C810 R816 C805_1
R513 R516 R103 R106 R525 C510 R511 R114 C416 C405 R407 R453 R403 R417 R415 Q411 R448 R461 R462 IC101 R409_1 C131 C146 C120 R126 R150 R519 C106 R137 C119 C111 R131 C121 C117 R125 R109 C115 R138 C102 C104 R110 R112 R113
SOLDER SIDE
R101
CMD016A
R128
C411 R449 R458 C439
Q103
R401
R135 C141 R136 R127 C643 C644 C637
PRINTED CIRCUIT BOARDS MAIN/CRT (CHIP MOUNTED PARTS)
IC199_1
C136 C137
Q711 R721
R711
R141 R627 R628 C138
R142 R143 R704 R129 C135 R618 R632 R145
R134 C128 C140 C142
R730
R708 R725 C619_1 R736 R728 R727 C735
Q712 R703 R617 C624 49 R610 R607 C614 C641 R1529 R1508
C143 C632 C631 33 17 C647 R612 1 R641 R608 R606 R604 C635 R613 Q603 Q605 Q614 R1510 C1516 C1512 R1528 R1504C1514 R1512 R1503 C616 R654 C612 C628 R636 R635 R611 C303 C301 R314 R620 C307 C309 C310 C313 R1522 C315 C322 C1507 Q1507 C1506 R746 C1503 R1520 C1508 C1533 C1504 R1502 C1505 R1516 R1518 C1526 R1519 C320 C741 C639 R625 R622 C913 C917 R634 R629 R912 IC902 R903 Q901 Q902 R906 IC302 C334 C311 C312 C915 C918 C912 C908 C911
R745
C720 C742
R724
27A45/27A45C F-4
A
ACCESSORY
MICON SCHEMATIC DIAGRAM

(MAIN PCB)
8
270 1/4W R120 OS101 RPM7138-WH5 B+ 3 GND 2 D109 SLR-342VCT32 POWER ON LED SW Q101 KTC3875S_Y_RTK 2.7 0 0 R109 1K Vout 1 5.0 0 4.9 25V 10 KA C108 TEST POINT CP101 173979-7 GND I2C_SCL I2C_SDA I2C_OFF GND R103 2.7K SW101 EVQ21505R SW103 EVQ21505R SW102 EVQ21505R VOL DOWN CH DOWN VOL UP CH UP 1 2 3 4 5 6 7 47 1/4W
BT001 GR03X-SP2
7
R101
560
R102
BT002 GR03X-SP2
TM101 R25-1939
R106
560 SW104 EVQ21505R SW105 EVQ21505R 1K 1/4W POWER R124
AUDIO L AUDIO R
R130 47K 1/4W
R150 1K
1.8 0 0 CLAMP SW Q103 KTC3875S_Y_RTK
FROM/TO CHROMA
100 1/4W
C142
R146
MICON IC IC101 1 5.0 4.0 0 NC AUDIO MUTE EXT MUTE VOLUME BBE SW AFT KEY 1 KEY 2 X RAY REMOCON ON_TIMER S_IN Y/C_SW AUDIO_SW OEC7090B 42 H_CTL PROTECT 12C_OFF SYNC H SYNC V SYNC BLUE B GREEN G RED R BLANK CLOCK_CNT SDA1 SCL1 0 R126 0 5.0 2.1 C137 C136 B B 4.0 4.8 0 C131 0 0 0 R141 R142 R143 820 820 820 5.0 NC 5.0 R135 5.0 R136 5.0 5.0 5.0 2.4 C113 2.0 2.0 1.0 5.0 R125 10 VCC C109 0.1 B 22 C117 47P CH R133 1K 1/4W C156_1 1 TF C128 0.1 MTZJ5.6B F 5 SDA 5.0 6 SCL 5.0 7 0 8 VCC 5.0 MEMORY IC IC199_1 BR24L16FJ-WE2 C111 0.001 19 B 0.1 B R131 1K 2 3.3K 3.3K 150P CH R127 C138 B 3.9K R128 3.9K R129 3.9K 10 33 0 W811 D105 10P CH R145 2.2K C135 1SS133 0.1 100 C120 0.001 B C146 33P CH
AT+5V PROTECT CLAMP_OFF SYNC_OUT HD VD OSD_B OSD_G OSD_R 0.1 D104 OSD_BLK 1SS133 SW_Y_OUT RESET POWER SDA SCL
6
TO SOUND
220P
CH R118 2.2K 1/4W
C143 220P CH
TV_MUTE
R110 10K
38
FROM TUNER/STEREO R112 5.0 5.0 2.2 25V 10 KA R114 47K R119 22K 1/4W C140 220P CH C141 220P CH 0 5.0 0 NC 3.5 H_CTL 5.0 MTZJ5.1B 3.2 NC 0 C102 C104 27P CH 27P CH X101_1 100CT8R005 8MHz 1 TO COMB FILTER Y/C_SW 2.3 1.7 0 0 5.0
AFT
2.2K R113 2.2K
37
0.1
3.2
39
40
41
FROM/TO AV
C139
34
35
36
EXT_MUTE S_IN AUDIO_SW
FROM/TO TUNER/STEREO
11
32
R139 100 1/4W R140 100 1/4W 4 3
J_AUDIO_OUT_R J_AUDIO_OUT_L SDA SCL FROM/TO SOUND
12
13
14
FROM/TO DEFLECTION
NC P FAIL DEGAUSS H X-RAY TEST CNVSS X.IN
POWER MCU_CLOCK RESET CVIN VHOLD HLF FILT
29
30
31
15
28
R134
10K
SDA SCL
16
27
X-RAY D106
C115 820P CH R132 R138 1M
0.1 B
17
C106
26
FROM/TO POWER
X-RAY P.FAIL
DEGAUSS_H GND POWER
24
100 1/4W C122 C119 50V 1 KA 220P CH C121 0.01 B
18
25
20
X.OUT VSS
21
23
YK
C114
R137
10K
D113
VSS
MODE
6.3V 2200
50V 0.47
C110
KA
E2
W822
E1 0 2 0
E0 1 0
PCB010 CMD016
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
G-1
27A45/27A45C
G-2
CHROMA SCHEMATIC DIAGRAM

8
(MAIN PCB)
FROM/TO AV VIDEO_IN2
V_IN[YUV] VIDEO_IN1 U_IN[YUV] Y_IN[YUV] VIDEO_IN3 R618
R616 120 1/2W R617 100 C631 8.2K 50V 0.47 KA 0.015 B X602 100CT3R505 C632 18P CH
8.8 5.5
4.9 AT+5V REG Q607 KTC3203_Y
VIDEO_OUT R603 330 1/2W D602 MTZJ8.2B
16V 47 YK
R634 R622 5.6K
16V 47 YK
50V 1 KA
1SS133
0.1
50V
0.1
FROM/TO COMB FILTER
6
C_V_OUT_SW P.CON+5V Y_V_OUT_SW VIDEO_OUT P.CON+8V[A] FSC_OUT 12 3W 12 7 R602 R649
50V
50V
0.1
3.579545MHz
C605
16V 47 YK
KA
KA
C614
C619_1
C610
C607
C611
C618
C621
C627
1 KA
D601
0.01
C624
C630
C622
1K
6
FROM/TO MICON 0 33 32 3.6 SW_Y_OUT 0 NC 5.0 3.5 NC 5.0 3.5 3.5 4.9 NC 4.2 2.9 C637 2.9 C643 2.9 C644 4.6 4.9 4.9 2.1 11 SYNC_OUT R629 6.8K D608 CLAMP_OFF 11E1-EIC W805 33P CH 33P CH 33P CH R627 SCL 100 R628 SDA 100 AT+5V RESET
2.7 P.CON+5V REG Q606 KTC3209_Y 5.0 7.2 3W 5.0 P.CON 5V REG Q602 KTC3209_Y 5.0 7.2 5.5 7.2 5.5 P.CON 5V REG Q604 KTC3209_Y 5.5 50V 1 KA 48 C641 0.1 B 2.2 49
0 3.0 47 46 CVBS1
0 1.2 45 44 NC(GND) U IN(YUV)
0 1.9 5.0 1.2 43 42 41 40 NC(GND) CVBS2 V/C VCC V IN(YUV)
0 1.9 5.6 2.8 39 38 37 36 NC(GND) CVBS3 MCU 5.7 VREG OUT C_APC
0 3.2 35 34 NC(GND)
12
PROTECT
C IN(Y/C) NC(GND) Y IN(Y/C) VREG VCC CVBS4
Y SW OUT NC MCU RESET
50
C642
51
52
MCU CLOCK OUT 47 NC(GND) 48 Y IN(YUV) 33 V/C GND 34 XTAL 3.58 SCL SDA CHROMA IC IC601 M61283FP R70T CLK CONT FAST BLK R IN 1 HVCO F/B 15 G OUT 2 AFC FILTER 16 B OUT G IN B IN V PULSE OUT HVCO F/BDEF GND1 INV.FBP OUT DEF GND2 DEF VCC MONITOR OUT HI VCC R OUT ACL 15 4.0 4.0 14 13 16 P_CON CONT
53
28
1.9 R610 100 C640 0.01 F 5.7 3.2 0 NC 0 2.8 NC 3.0 3.0 8.7 4.0
29
8.7
30
3.0
31
POWER
5
54
5.7V VREG OUT fsc OUT NC FAST YUV DELAYDE Y OUT EW OUT VIDEO LINE OUT 8.7 VREG OUT VRAMP AGC CAP LOGIC GND V OUT VRAMP CAP 1 2 4.0 0
55
C603
TUNER_VIDEO TUNER+5V P.CON+8V[B] P.CON+5V
16V 47 YK
56
57
24
25
26
27
OSD_BLK OSD_R OSD_G OSD_B VD HD
10 1/2W
58
60
61
P.CON+8V[B]
2.2
R613 390 22P CH R604 C635 R606 330 R608 3.9K
62
63
1K
NC(Vcc)
64
NC
3 0
4 0
5 5.5
6 0
7 NC 3.8
8 8.0
9 8.0
10 0
11 8.0 NC
NC
FROM POWER R601_1 15 1W
12 8.0
13 4.0
14
UNREG+12V GND
MMTS
P.CON 8V REG Q611 KTC3209_Y 11.3 8.5 7.9 TF C606 0.33
W815
3.2
17
4.0
NC(Vcc)
FBP IN
H OUT
18
4.0
19
20
3.8
1.7
2.3
16V 47 YK
21
TO SOUND
6dB AMP Q603 KTC3875S_Y_RTK
6dBAMP Q614 7.9 7.8 KTA1504S_Y_RTK 7.3 3.8
7.3
6dB AMP Q605 KTC3875S_Y_RTK C608
R605
R648
330 R607
10K
59
22
23
15
R654 C609_1 R641 10K 56K 50V 1 KA C615
16V 10
R632
0.1
6.8K
CH
C647
11.3 8.5 R609
16V 100 YK
C612
0.01
C616
0.012
100P CH D605
C639
1SS133
MTZJ12B
C629
16V 47 YK
C602
0.1
100
D604
D606
C628
D607
FROM/TO DEFLECTION P.CON+5V P.CON+8V[A] GND V_OUT EW_OUT H.OUT H_SYNC
1SS133
1SS133
1.5K B R612
16V 1000 YK
C645
100P
10
R636
C646
7.9
120K B
100P CH
33K
R635
R625
C638
P.CON 8V REG Q601 KTC3209_Y
KANP
TO CRT/SVM CP802A (CP802B) B2013H02-7P P.CON+8V R620 100 R623 100 1/4W R626 100 1/4W NC GND R.OUT G.OUT B.OUT CLAMP_OFF 1 2 3 4 5 6 7
R611
6.8K
10K
ABCL
PCB010 CMD016
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES

DESCRIBED IN PARTS LIST ONLY
ARE
G-3
27A45/27A45C
G-4
DEFLECTION SCHEMATIC DIAGRAM

(MAIN PCB)
8
FROM/TO DY V.OUTPUT IC IC401 LA78041 R401 4.7K + 560 1/2W 560 1/2W 560 1/2W 100P CH PUMP UP VCC GND 1 2 3 4 4.0 25.0 2.0 0 C422_2 R421 R429 R433 C416 THERMAL PROTECTION MKT AMP 18 CP401 B06B-DVS-L (LF) 6 5 L402_1 ELH5L4132N NC NC 4 3 2 1 R439 C407 35V 100 YK 820 1/2W 1K 1W C425_1 2KV 0.001 RR 6 5 4 3 2 1 V801 M68LWF088X50
R407 1.2K 1SS133 1SS133 1SS133 D419
16
12.0
25.0 17
4.0
100V
9 10 8 6 11
R G B 5 7 1
0.1
7
1 2
TO CRT/SVM
220 1/4W +-1%
W836
R455_2
11E1-EIC
D416
D402
R427
25V 1000 MHE
R462
R415
R418
10K
8.2K +-1% 820 12K +-1% 560P CH R413 R458
100V 0.22 MKT
820 1/2W
2.9 2.9 0
BUFFER Q409 KTA1266 2.3 R456 5.6K 1/2W
4.7K 1/4W
CD803 (CP803) C3823005
D417
R457
R414
R417 FB401 115 1 V.POSI ADJ VR401_1 2.2K METAL 180 6 108.0 2 105.0 9 0 10 0 C417_1 COL E180 B+ AFC HEA TER F S GND 0 11 ABL 8.1 FJN27A003_M HV 39K C408
C405
1.0 0.4
C409
R448
2.5
0.7
R459_2 1 1/2W UHT
50V 10 YK
BUFFER Q408 KTA1266 0.7
50V 1 YK
C406
D403
BUFFER Q411 KTC3875S_Y_RTK
1K
2.5
R419
FROM/TO CHROMA R449 27K R461 1.5K V_OUT EW_OUT GND P.CON+8V[A] P.CON+5V H.OUT H_SYNC ABCL C401 HS401 763WAAA063
W827
W828
W823
50V
DRIVE Q410 2SC4159
C442
6.8
680 1/2W
R437
6.5
1 1/2W
D410
MTZJ30B
1W
MTZJ30B
68K
R422
1.2
GND 8 0.2 E12 4 NC E27 2.0 3 21 ERD07-15L50 02DK000058 8 630V 0.022 CPP 1.25KV 0.015 CMPP GND
C411 0.001 CH 19 R406 C402 470 1/2W 100V 0.01 MMTS T401 ETH19Y203AY 0 5 1 0.1 20 4 CMPP H.OUT Q405 2SD2499(LBOEC1) 115 B405 0.1 100 1/4W B403 0 W4BRH3.5X6X1.0
0.1 E8 NC 5 L403 PMS
D408_1
C412_1
250V 0.43
500V 27P SL R409_1 1K R453 10K R403 FROM/TO POWER H.DRIVE Q402 KTC3227_Y 17.3 0.4 1K 0
0 26.3
1.25KV 0.0027
C418
C420_1
17.3
5
TP004 PROTECTOR TEST TP003 ANORD
W4BRH3.5X6X1.0 22 YK R428
FE201-6L49
C403
HS402 763WAAA050
GND R434 +B 1.8 10W W863 R452 390 2W D414 11E1-EIC
50V
C421_1
D409
FORCUS FROM/TO CRT SCREEN
FBT+B
D415 11E1-EIC
R410_1 47 2W
D405 AU02A-EIC
H+B
R443 150K 1/2W
W861
R404 MTZJ5.1B 100 D404
R432 68K 1/2W 8.2K 1/2W R430 C415 500V 150P B
C427_1 100V 0.1 MKT
3
AU02A-EIC D407
FROM/TO MICON 1.2 2W R438 R436 18K 1/4W +-1% TP005 TP006 R441 15K +-1% 100V 22 YK C430
H_CTL W844 4.7K 1/4W +-1% MTZJ5.6B 0.01 B D411 AU02A-EIC
35V 1000 YK
X-RAY D406 R426
C413_1
TO CRT/SVM MHE CP801A (CP801B) B2013H02-5P 180V NC NC NC NC GND HEATER 1 2 3 4 5
C439
C426
250V 22
X-RAY TEST
PCB010 CMD016 PCB010 CMD016
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.

ARE
G-5
27A45/27A45C
G-6
POWER SCHEMATIC DIAGRAM

8
(MAIN PCB)
D516 1SS133 10.9
RELAY DRIVE Q504 KTC3198 0
R515 10K 1/4W
250V 0.001
250V 0.001
C513_1
C519_1
7
RY501 G5PA-1-SA(WEC) DEGAUSS COIL L503 8R270010 1 2 TH501_1 CP507 003P-2100 1 1 2 3 CP502 A1561WV2-2P 1 2.7M 1/2W +-10%
7
KX TO SOUND D505 25V 2200 YK 30PRA60-FC C501 R501 RM11C-EIC RM11C-EIC 1 7W R541_1 0.22 1W 1.2M 1/4W R539 W806 R517_1 SOUND+B 0.39 3W 1SS133 P.CON+12V GND SOUND_GND D517 R503 1SS133 10K 1/4W CURRENT DET. Q512 2SA1624 D514 38 R537 100K 1/4W 115.4 115.7 C539 C510 0.01 B 115.5 R505 10K 1/4W YK 3.9K 1/4W R535 82K 1/2W 115.1 114.7 +B SW. Q503 2SA1371 1SS133 FROM/TO DEFLECTION H+B +B FBT+B GND
R500
KX
D501
R540
C502_1 275V 0.1 ECQUL
C503_1 200V 470 UP C507
6
BLADE WIDE CP501 A3963WV2-3PD 2 2 WHITE 1 1 BLACK WHITE
275V 0.22 ECQUL
ZPB45BL3R0A 1.5M 1/2W 1 R520 CP508 003P-2100 C505_1
1.2M 1/4W
COIL,LINE FILTER L501 2R2A752F28Y
D502
D513
RM11C-EIC
C506_1
AC120V_60Hz CD501_1 09615904
D504
D503
RM11C-EIC
MTZJ18B
2KV 2KV 0.001 RR 0.001 RR
D523
F501 BLACK 6.3A125V FH501 FH502 EYF-52BCY EYF-52BCY 6.3A125Vor51MS063L 8
T501
8140066S
50.0
9 P1 7 10 NC
141.6 0
6
25.0 0
11
W825 B504 220P CH
2KV 0.0015 R D510 160V 220 ED
47K 1/4W R527 0.68 2W
R507_1
C517
50V 2.2 R536
115.2 STAND BY SW. Q505 2SC2909 0 0 R513 10K
R516 10K TO TUNER/STEREO P.CON+B GND
BL02RN1-R62 159.4 SWITCHING Q502 159.4 D 2SK3326(2) G 5.3 5.3 0 S SWITCHING Q514 KTC3203_Y R544 270 1/4W D507 1SS133 0
13 R502 330 2W 1.5 C524 C512 100V 0.047 MMTS 500V 0.001 B 2 HS501 763WAAA064 1 16
138.9
3 14
2KV 0.0022 R
C535
26.0 15
C511
C521_1
6.3A 125V
W801
B501
40.0
5
P2
W5RH3.5X5X1.0 FE201-6L49
240.0 12 NC
TO CHROMA UNREG+12V GND
R542
4
10.7 1 C554 2 0.022 B 6.3 W817 5.7 1/2W R553 9.7 FEED BACK SWITCHING Q507 KTC3198 R532 1.5K R510 100 1/4W R533 270 9.7
0.15 1W
FROM/TO MICON 50V 2.2 YK R545 150 1/4W D524 1SS133 D511 1N4937 R546 100 1/4W C504 R524 P.FAIL R525 3.3K 1/4W 15K X-RAY DEGAUSS_H POWER GND C520 500V 0.001 B
16.3 4 D509 3 1.5 FEED BACK IC504 LTV-817M-VB MTZJ18B R508 D506
100 1/4W 1N4937
25V 47 YK
0.056 B
1K 1/2W
R543_1
C541
C509
D512 GND1 21DQ09N R511
12.9
12.9
C550 35V 220 YK
3
1/4W R506 R554
15K
12.8
100K 1/2W
MTZJ15B
D525
22K 16V 2200 YK R512
MTZJ5.6B
CAUTION:
MTZJ6.2B D508 250V 0.0022 KX C508_1
IS THE LIVE CONNECTION

C523 0.001 CH
D528
1K 1/2W
P.CON+12V SW. Q508 KTA1271_Y
6.8K
100 1/4W
1SS133
TO AV 0.7 R519 10K P.CON+12V GND FROM/TO COMB FILTER GND
D520
+B ADJ
VR502 22K
C527
R547
0.8 STAND BY SW. Q509 KTC3198
2
PCB010 CMD016
6.3A 125V
CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, 6.3A 125V(F501)

REPLACE ONLY WITH THE SAME TYPE FUSE DINCEIE ATTENTION:POUR UNE PROTECTION CONTINUE LES RISQUES 6.3A 125V(F501) NUTILISER QUE DES FUSIBLE DE MEME TYPE
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.

ARE
G-7
27A45/27A45C
G-8
SOUND SCHEMATIC DIAGRAM

8
(MAIN PCB)
50V 10 YK
220K C333
R314
C315
C307
0.1
C319
0.015
FROM TUNER/STEREO
0.033
C301
50V 10 YK
C304
C309 0.039 B 3.9 3.9 6 7 PF2 PF3
3.9 1 PF1 TONE CONTROL IC IC302 AN5891SA-E1V
1.7 2 AGC
3.0 3 L IN
NC 4 NC
NC 5 NC
3.9 8 PF4
0 9 GND
4.0 10 LT
4.0 11 LB
NC 12 NC
NC 13 NC
C317
2.0 14 BD
2.9 15
4.0 16 VD L ONT
AGC
SURR
Tone Control
Volume 2.2K Control
+ + NC 21 0 NC 0 NC C318 NC 20
Balance /MUTE
MODE control VCC 32 2.3 7.9 31
C321
2.7K 1/4W
50V 10 YK
50V 10 YK
SW_AUDIO_R
0.033 B
SW_AUDIO_L 22
23 R301
R302 2.7K 1/4W
0.01
50V 10
C310
C313
YK
R IN 30 4.5 C305
Vref 29 4.0 50V 10 YK 0
NC 28 0 NC
NC 27 4.0 NC
BB 26
RB RT BLD TD 25 24 23 22 4.0 4.4 3.0 2.0
R OUT SDA SCL 19 18 17 4.0 3.5 3.5 50V 10 YK
W832
50V 10 YK
50V 10 YK
C334
C312
C316
50V 10 YK
C302
C308
0.01
R303 100 1/4W W831 R304 100 1/4W
FROM CHROMA
L301 P.CON+8V[B] 16V 100 YK AT+5V C306 100uH 0305
50V 10 YK
C311
0.1
C314
FROM/TO COMBI FILTER
GND FROM/TO MICON SDA SCL
4
TV_MUTE S810X SOUND AMP IC IC1001 AN17808B + + ATT. + VOL CH2 VOL MUTE OUT 6 7 8 0 0.7 3.7 STAND CH1 GND VCC -BY OUT 9 10 11 12 0.7 0 16.5 12.7 RIPPLE FILTER CH1 CH2 NC GND RF IN IN 1 2 3 4 5 0 NC 0.2 16.0 0 0.2 + ATT.CONT. 25 24 CP1001 A2502WV2-4P 4 3 2 1 W803 R1003 15K R1004 25V 2200 YK 0.0047 B R1011 0.0047 B C1012 15K 25V 1000 YK 25V 1000 YK R1010 12K C1001 50V 0.1 YK C1002 50V 0.1 YK 4 3 2 1 (R) (L) W/CONECTOR.2SPEAKER SPEAKER SP1001_1 S0509F12A-F 8 OHM 2.5W
47P CH C322
47P CH
C303
0.01
C320
FROM POWER
SOUND+B
GND P.CON+12V SOUND_GND
S810Y
12K C1010
C1009
C1004
W858
C1003
R1013 R1014 35V 220 YK (5MM) 10K R1009
S809Y
W835
220P B
C1005
C1008_1
3.6 0
KA
6.8K
10K 1/4W
R1015
C1011_1
820
1/4W
26
W833
50V 10
27 HS1001 763WAAA062
W834
MUTE Q1001 KRC111SRTK
S809X PCB010 CMD016

ARE
CAUTION: DIGITAL TRANSISTOR
G-9
27A45/27A45C
G-10
TUNER/STEREO SCHEMATIC DIAGRAM

8
(MAIN PCB)
TU001
19
115-V-KA35ARB 9 (ADRESS) 14 SIF OUT 8 (XTAL) 16 IF OUT AUDIO OUT VIDEO OUT
20
11 SDA
10 SCL
12 AFT
MB
MB
15 BT
FROM/TO CHROMA
21
13
18
17
7
W812
NC
NC
NC
NC
NC
NC NC
NC
NC
NC
TUNER+5V TUNER_VIDEO P.CON+8V[B]
C002
P.CON+5V
0.1
10V 100 YK
C001_1
R006
6
W819 W820
100
MTZJ33B
F 0.1
D001
C005
FROM POWER R001 P.CON+B 68K 1/2W R002 68K 1/2W TO MICON GND
AFT
220 1/4W
56K 1/4W
FROM/TO MICON R901 SCL SDA J_AUDIO_OUT_L
220 1/4W
R902
3.2 2.3 BUFFER Q901 KTA1504S_Y_RTK 0 50V C901 1 KA
J_AUDIO_OUT_R
4
3.2 2.3 BUFFER Q902 0 KTA1504S_Y_RTK R906 R903 39K 39K 50V 50V 10 YK C902 W829 W830 C919 330 1 KA R912
56K 1/4W
R904
R905
TO SOUND L901 SW_AUDIO_L 0.047 B C913 B 0.1 B SW_AUDIO_R C911 100uH C917 0305
3
24 SOUND DECORDER IC IC902 AN5829S 2.3 23 2.3 22 2.3 21 2.3
DAC
0.1
NC 20
19
5.0
18
5.0
GND
17
16
3.7
15
3.6
14
2.6
13
Det SAP
3.7
AGC Matrix
OUT SW
ZAP IIC Decoder L-R Filter L+R Filter L-R Demod L+R Demod
St.PLL Cancel Pilot Filter Stereo
Det Pilot Filter Noise Filter Spectral
VCA Input
FROM/TO AV
J_AUDIO_OUT_L J_AUDIO_OUT_R AUDIO_IN1/2[R] AUDIO_IN1/2[L] AUDIO_IN3[R]
Switch De-Emph (L-R)/SAP 75us Filter Cancel SAPout Offset Expand Cancel Wide Band Offset
Filter SAP Demod SAP Det Noise
fH.2fH Trap Filter RMS Det Wide Band dbx De-Emph
Filter Wide Band Expand Spectral
2.3 1 0 2 2.3 3 2.3 4 2.2 50V 4.7 KA 5
RMS Det Spectral
6 2.2 0.4 50V 10 YK
Vcc
8 2.4 50V 0.33 KA
9 2.4
10 0.4 50V 3.3 KA
11 2.3 C918
12 3.4 0.1 B
5.1
C907
C904
50V 4.7 KA
50V 4.7 KA
C910
AUDIO_IN3[L]
C914
10V 100 YK
39K C903
R907
0.022 B
0.022 B
C912
C905
C908
C915
0.1
C916
PCB010 CMD016

ARE
G-11
27A45/27A45C
G-12
AV SCHEMATIC DIAGRAM
8
FROM/TO CHROMA 28 V_IN[YUV] U_IN[YUV] Y_IN[YUV] VIDEO_OUT R725 D701 VIDEO_IN2 VIDEO_IN1 VIDEO_IN3 75 29 MTZJ12B MTZJ12B R730 MTZJ12B D702 75 D703 R736
(MAIN PCB)
H1 YUV_IN(REAR) J704 MSP-213V1-652_NI 2 1 E
H2
7
C707 270 1/4W R702 R709_1 16V 100 YK 220 1/4W C708 25V 10 KA R704 1K
75 H1
A/V_OUT(REAR) J708 MSP-213V2-432_NI

H1 NC H1 H2
C711 25V 10 KA
R708 1K C728 MUTE Q711 KTC3875S_Y_RTK R710 1K 1/4W 0 0.1 R721
16V 470 YK 68
R705
3.3K
R703 4.6 5.2 BUFFER Q709 KTA1504S_Y_RTK 2.2K
R711 1K
0.2 0.1 0
C710 16V 47 KANP
0.2 MUTE Q712 KTC3875S_Y_RTK
R706
3.3K
6
LINE2(REAR) J703 MSP-213V2-432_NI
H1 NC H1 H2
C727 1 B C724 1 B
R734 1K R728 1K MTZJ12B 0.0056 B 0.0056 B
D705
C737
R727
C735
75
AUDIO SW(R) IC IC701 MM1501XNRE Vin1 GND Vin2 6 4.5 0 4.5 C725 1 5 B C722 1 B R733 1K R726 1K MTZJ12B
LINE1(REAR) J701 MSP-213V2-432_NI

H1 NC H1 H2
J_AUDIO_OUT_R J_AUDIO_OUT_L C702 AUDIO_IN1/2[R] C701 AUDIO_IN1/2[L] AUDIO_IN3[L] AUDIO_IN3[R] 25V 10 KA 25V 10 KA R701 16V 220 YK 560 1/4W C705 F
3.7 12.7
V.OUT Vcc
C706
C733 16V 22 KA R739 75
S-JACK J702 YKF51-5503N 1
4
FROM/TO MICON AUDIO SW(L) IC IC702 MM1501XNRE EXT_MUTE AUDIO_SW S_IN 1 6 0 3.7 12.7 SW1 V.OUT Vcc Vin1 GND Vin2 4.5 0 4.5
0.1
0.0056 B
0.0056 B C736
R729
D704
C738
75
SW1
C734 0.1 B
R735
75
2 D709
3
TO COMB FILTER
FRONT-VIDEO J705 MTJ-032-03A-30FE

NC
MTZJ6.2B
S_VIDEO_IN[Y] S_VIDEO_IN[C] MTZJ12B R724 D706 75
FRONT-AUDIO.L J706 MTJ-032-03A-32FE

NC
C719 1 B
R745 1K
2
FROM POWER P.CON+12V GND C720 1 B R746 1K
0.0056
FRONT-AUDIO.R J707 MTJ-032-03A-31FE

NC
C741
LINE3_A_IN_L
0.0056 B
C742
LINE3_A_IN_R
PCB010 CMD016
G-13
27A45/27A45C
G-14
CRT SCHEMATIC DIAGRAM

8
(CRT PCB)
FROM DEFLECTION FROM DEFLECTION CP806_1 2KV 0.001 B CP801B (CP801A) B2013H02-5P SCREEN W802 C802 NC NC
1 2 3 4 5
180V NC NC GND HEATER FROM CHROMA CP802B (CP802A) B2013H02-7P RED/GREEN OUT Q804 KTC4217 220 123.0 7.4 D801 1SS133 37 R808 GREEN/RED OUT Q805 KTC4217 125.0 7.4 D802 1SS133 39 4.7K BLUE OUT Q802 KTC3199_Y 390 BLUE OUT Q806 KTC4217 7.4 R810 220 128.0 7.0 D803 1SS133 7.0 14F:RED OUT 27":GREEN OUT 6.9 14F:GREEN OUT 27":RED OUT 38
R802 R803 12K 2W 2.7K 1/4W
FOCUS
C805_1
0.1 F
2 3 4 5 6 7
GND R.OUT G.OUT B.OUT CLAMP OFF NC
R812 100 (27"RED) D810 1SS133
3.2 2.7
R809 4.7K GREEN/RED OUT Q803 98.4 KTC3199_Y C811 390P B R813 390 220 R817 68
R801
CLAMP
RED/GREEN OUT Q801 100.6 KTC3199_Y
R806
R807 12K 2W
2.7K 1/4W
R820 100 (27"GREEN) D811 1SS133
2.7
96.4
3.2
R814
96.4 8
C810 390P B R816
R818 68
0 9 6.4 10 11 12 NC 1 CP803 2 A2361WV2-2P 96.4 FROM BRAIDED WIRE
99.6 0 0 6 5 4
R804
R805 12K 2W
2.7K 1/4W
R821
95.4 2.7
C809 390P B R815 390 R819 68
1
0
100 D812 1SS133
3.2
F CRT SOCKET J801_1 ISHS53S 27"NORMAL NECK
R811 4.7K
C801 500V 100P B R824 100 1/2W
CCD010 PCB110

ARE
G-1
27A45/27A45C
G-16
COMB/FILTER SCHEMATIC DIAGRAM

8
(MAIN PCB)
L1511 15uH 0305
7.9 2.5 2.0
C1535 L1505 R1530 15uH 0305 R1503 R1505 6.8K 270 25V 10 470 KA FROM AV S_VIDEO_IN[C] R1512 W848 470 C1513 0.1 B 1.0 1.0 100P CH 5.0 BUFFER Q1503 KTC3875S_Y_RTK S_VIDEO_IN[Y]
6
10V 100 YK 0.01 B C1509 C1510
0.01 B
C1528
C1531
16V 100 YK
C1519 0.1 B 4.5 0 4.5
VIDEO SW(Y) IC IC1502 MM1501XNRE Vin1 GND Vin2 SW1 V.OUT Vcc 6 1 0 4.4 7.9
FROM MICON Y/C_SW
C1517
R1506
R1507
3.3K
1K
VIDEO SW(C) IC IC1503 MM1501XNRE COMB FILTER IC IC1501 LA76605M-TLM 2.6 2.4 CIN COUT 18 1 4.9 INSEL YIN2 GND AVCC DVCC SAND CASTLE OUTSEL YOUT GND YIN1 AFC RD 2 4.2 3 0 4 4.9 5 4.9 6 C1502 10V 100 YK C1503 0.1 B C1506 4.0 0.1 B C1507 2.1 PHASE DET FSC_IN GND GND 8 0.1 B 0 9 7 0 17 3.4 C1523 C1532 16 F 0.1 0 15 C1514 R1528 0.1 B L1508 R1529 C1521 0.1 B R1509 10V 100 YK 2.9 14 3.6 13 6 1 4.5 0 4.5 0 Vin1 GND Vin2 SW1 V.OUT Vcc
FROM/TO CHROMA Y_V_OUT_SW
C1504 0.1 B R1502
4.4 7.9 16V 100 YK L1501
C_V_OUT_SW P.CON+8V[A] 100uH 0305
100
C1505 1 B
4
10V 100 YK C1501 L1502 220uH 0305 L1503 220uH 0305
C1508
0.1 B
P.CON+5V 15uH 0305 100uH 47K C1520 0305 L1510 R1523 100 R1510 47K R1518
12
82K C1516 2.7K R1504 C1518 0.1 B 9.5 C1512 8.2K 50V 1 KA 0.9 0.1 B C1515 0.1 B
5.0 BUFFER 2.4 Q1504 KTC3875S_Y_RTK 2.0 R1508 3.9K
FSC_OUT
11
10V 100 YK
0 10
0.01 B
C1525
C1526
5.0 2.2 1.6 R1519 24K 1K
27K C1530_1 16V 47 KA R1520 C1533 22P CH 1.2K
L1512 22uH
R1522 VIDEO_OUT 1K
R1516
FROM/TO POWER
GND
FROM/TO SOUND GND
PCB010 CMD016
G-17
27A45/27A45C
G-18
MICON
WAVEFORMS
1 1V 0.1s/div
0.5V 10ms/div
13 1V 20s/div
2 1V 1s/div
9 1V 50s/div
14 2V 20s/div
3 1V 50s/div
10 2V 20s/div
15 2V 20s/div
DEFLECTION
4 1V 0.1ms/div
11 0.5V 20s/div
16 2V 5ms/div
CHROMA
7 1V 20s/div
12 1V 2s/div
NOTE:
17 20V 5ms/div
The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-1
27A45/27A45C
WAVEFORMS
18 10V 10ms/div
38 50V 20s/div
25 2V 5ms/div
19 20V 20s/div
39 50V 20s/div
26 5V 2ms/div
SOUND
20 2V 20s/div
22 2V 5ms/div
27 5V 2ms/div
AV
21 200V 50s/div
23 2V 5ms/div
28 200mV 20s/div
CRT
37 50V 20s/div
24 2V 5ms/div
29 200mV 20s/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-2
27A45/27A45C
MECHANICAL EXPLODED VIEW

201 107 102C 201 201 201 203 201 109 102B 202 201 109 111 102A 102B
106
202 PCB110 (CRT PCB ASS'Y)
102
201
202 112 109
202 110 204 112 109 206 103 206
203 207
105
207
203
104 101G 205 101G
203
101G 101F 203 101D
PCB010 (MAIN PCB ASS'Y)
101B 101E 101C 101A
101
I-1
27A45
MECHANICAL EXPLODED VIEW

201 107 102C 201 201 201 203 201 109 102B 202 201 109 124 111 102A 102B
106
202 PCB110 (CRT PCB ASS'Y)
102
201
202 124 109
124
202 110 204 206 103 206
124
109
203 207
105
207
203
104 101G 205 101G
203 108
101G 101F 203 101D
PCB010 (MAIN PCB ASS'Y)
101B 101E 101C 101A
101 I-2 27A45C
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM)
121,122, 123, TM101
115
115
114
119
117
118
116 113
I-3
27A45/27A45C
MECHANICAL REPLACEMENT PARTS LIST

Location No. TSB P/N
101 101A 101B 101C 101D 101E 101F 101G 102 102A 102B 102C 103 104 105 106 107 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 201 202 203 204 205 206 207 AE006022 AE006136 AD301618 AE006137 AD301620 AE006138 AE006139 AE003071 AE006926 AE006927 AE006141 AE004107 AD301616 AE004293 AE003190 BZ710660 AE006928 AD300768 BZ710260 AE006143 AD302158 AE006929 AE006145 AD301626 AD301627 AE006930 AE000232 AE006147 AE006931 AE005582 AE006932 AE004983 AE003522 AE006150 AE003528 AE003524 AE005917 AE003531 AE005659
Reference No.
7A701A361A 701WPJC970 711WPAA088 712WPBA126 713WPAA090 723549A042 735WPBB362 800WQ0A041 7A702A108A 702WPAA831 800WQ0A105 800WQ0A076 761WPA0263 800WQ0A066 800WQ0A067 741WUA0021 722549A444 762WPA0009 899HV3T000 726000A094 800WR0A002 723000C861 791WHAA116 792WHA0416 792WHA0417 793WCDC667 795WCA0665 795WCDA014 A3S2022975 JA4KD200 J3S20221A J2D60117A 8117540B0U 8141J50D5U 8110630A0U 8109I30A0U 810963080Q 810763080U 8109I3080U FRONT CABI ASS'Y CABINET,FRONT PLATE,FRONT DOOR GLASS,LED AV LABEL BUTTON ASS'Y FELT SHEET BACK CABI ASS'Y CABINET,BACK FELT SHEET FELT SHEET HOLDER,JACK FELT SHEET FELT SHEET SPRING,EARTH SHEET,RATING HOLDER,CRT WIRE
Description
HOLDER,ANODE WIRE SHEET,CRT SERVICEMAN SHEET,CRT SUPPORT SHEET,BAR CODE FILM BAG PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX PAD PAD
378x1114
INSTRUCTION BOOK KIT POLYBAG,INSTRUCTION(RED CAUTION) INSTRUCTION BOOK(E/S) REGISTRATION CARD SCREW,TAP TITE(B0) TRUSS SCREW,TAP TITE(P) GW20 SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(B) WH7 SCREW,TAP TITE(B) BRAZIER SCREW,TAP TITE(S) BRAZIER SCREW,TAP TITE(B) WH7 4x20 5x45 3x10 3x10 3x8 3x8 3x8
J1-1
27A45
MECHANICAL REPLACEMENT PARTS LIST

Location No. TSB P/N
101 101A 101B 101C 101D 101E 101F 101G 102 102A 102B 102C 103 104 105 106 107 108 109 110 111 113 114 115 116 117 118 119 120 121 122 124 201 202 203 204 205 206 207 AE006022 AE006136 AD301618 AE006137 AD301620 AE006138 AE006139 AE003071 AE006926 AE006927 AE006141 AE004107 AD301616 AE004293 AE003190 BZ710660 AE006142 AE006088 AD300768 BZ710260 AE006143 AE006144 AE006145 AD301626 AD301627 AE006146 AE000232 AE006147 AE006148 AE006098 AE006149 AE005971 AE003522 AE006150 AE003528 AE003524 AE005917 AE003531 AE005659
Reference No.
7A701A361A 701WPJC970 711WPAA088 712WPBA126 713WPAA090 723549A042 735WPBB362 800WQ0A041 7A702A108A 702WPAA831 800WQ0A105 800WQ0A076 761WPA0263 800WQ0A066 800WQ0A067 741WUA0021 722549A420 724000A006 762WPA0009 899HV3T000 726000A094 723000C811 791WHAA116 792WHA0416 792WHA0417 793WCDC594 795WCA0665 795WCDA014 A3S2012975 JA4KD100 J3S20121A 769WSAA012 8117540B0U 8141J50D5U 8110630A0U 8109I30A0U 810963080Q 810763080U 8109I3080U FRONT CABI ASS'Y CABINET,FRONT PLATE,FRONT DOOR GLASS,LED AV LABEL BUTTON ASS'Y FELT SHEET BACK CABI ASS'Y CABINET,BACK FELT SHEET FELT SHEET HOLDER,JACK FELT SHEET FELT SHEET SPRING,EARTH SHEET,RATING SHEET,CSA HOLDER,CRT WIRE
Description
HOLDER,ANODE WIRE SHEET,CRT SERVICEMAN SHEET,BAR CODE FILM BAG PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX PAD PAD
378x1114
INSTRUCTION BOOK KIT POLYBAG,INSTRUCTION(RED CAUTION) INSTRUCTION BOOK WASHER CRT T=0.5 SCREW,TAP TITE(B0) TRUSS SCREW,TAP TITE(P) GW20 SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(B) WH7 SCREW,TAP TITE(B) BRAZIER SCREW,TAP TITE(S) BRAZIER SCREW,TAP TITE(B) WH7 4x20 5x45 3x10 3x10 3x8 3x8 3x8
J1-2
27A45C
ELECTRICAL REPLACEMENT PARTS LIST

Location No.
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! R409 R410 R419 R426 R429 R434 R436 R438 R439 R441 R452 R457 R459 R461 R500 R501 R502 R506 R507 R517 R520 R527 R533 R541 R542 R543 R601 R602 R629 R649 R803 R805 R807 R1014 C156 C408 C412 C413 C418 C420 C421 C425 C426 C430 C442 C501 C502 C503 C504 C505 C506 C507 C508 C513 C517 C519 C521 C527 C535 C802 C1003 C1004 C1009 D001 D104 D105 D106 D109 D113
TSB P/N
AE001783 AD302107 AD300784 BZ210030 AE000145 AD300421 BZ210023 BZ210022 BZ210003 BZ210231 AD301385 BZ210122 AD301595 AE000849 BZ210080 AD301596 BZ210249 BZ210162 AE002597 AD302108 BZ210206 BZ210149 AE002872 AE005735 BZ210248 BZ210180 AE006340 AD301975 AE001801 AD301975 BZ210050 BZ210050 BZ210050 AE006741 AE004040 BZ110032 AD301599 AD301977 AE001019 AD300723 AD301600 BZ110202 BZ110225 BZ110195 AE006084 BZ210176 BZ110202 BZ110202 AD301729 BZ110025 BZ110035 BZ110012 BZ110222 AD301026 BZ110191 AD301026 AE006083 BZ110119 BZ110201 BZ110247 BZ210176 BZ110053 BZ110053 BZ410037 BZ410006 BZ410006 BZ410020 BZ410054 BZ410021
Reference No. RESISTORS

R803R9102J R3X18A470J R3X1811R2J R4X5T4472F R002T2561J R5X2CF1R8J R4X5T4183F R6558A1R2J R3K181102J R4X5T6153F R3X18A391J R002T4472J R65582010J R803R9152J R0G3K2275K R5X2AE010J R3X28A331J R002T4682J R00202823J R3X28BR39J R002T2155J R3X18AR68J R803R9271J R63881R22J R3X181R15J R002T2102J R3X181150J R3X28B120J R803R9682J R3X28B120J R3X18A123J R3X18A123J R3X18A123J R00204821J P6M900105J E5EZF3102M P4N8FJ272H E0ELF4102M P4J7F3434J P4N8FJ153H P3N1F5223J C0PLRR713K E5EZFD220M E02LU8220M E736F56R8M E02LF3222M C0PLRR713K C0PLRR713K E02LU52R2M P2122B224M P2122B104M E51CGC471M CD39E0MH3M CD39E0M13M C03L0R7E3K CD39E0M13M E61DFB221M E02LF2222M C0PLRR7H3K C0JBB0713K E02LF3222M E02LF3102M E02LF3102M D97U03301B D1VT001330 D1VT001330 D97U05R11B 0021721150 D97U05R61B RC R,METAL OXIDE R,METAL OXIDE R,METAL RC R,CEMENT R,METAL R,FUSE R,METAL OXIDE R,METAL R,METAL OXIDE RC R,FUSE RC RC R,CEMENT R,METAL OXIDE RC RC R,METAL OXIDE RC R,METAL OXIDE RC R,FUSE R,METAL OXIDE RC R,METAL OXIDE R,METAL OXIDE RC R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE RC CMPL CE CMPP CE CMPP CMPP CPP CC CE CE CE CE CC CC CE CMP CMP CE CC CC CC CC CE CE CC CC CE CE CE
Description
1K OHM 1/16W 47 OHM 2W 1.2 OHM 1W 4.7K OHM 1/4W 560 OHM 1/2W 1.8 OHM 10W 18K OHM 1/4W 1.2 OHM 2W 1K OHM 1W 15K OHM 1/6W 390 OHM 2W 4.7K OHM 1/4W 1 OHM 1/2W 1.5K OHM 1/16W 2.7M OHM 1/2W 1 OHM 7W 330 OHM 2W 6.8K OHM 1/4W 82K OHM 1/2W 0.39 OHM 3W 1.5M OHM 1/2W 0.68 OHM 2W 270 OHM 1/16W 0.22 OHM 1W 0.15 OHM 1W 1K OHM 1/2W 15 OHM 1W 12 OHM 3W 6.8K OHM 1/16W 12 OHM 3W 12K OHM 2W 12K OHM 2W 12K OHM 2W 820 OHM 1/4W 1 UF 50V TF 1000 UF 25V 0.0027UF 1.25KV 1000 UF 35V 0.43 UF 250V PMS 0.015 UF 1.25KV 0.022 UF 630V 0.001 UF 2KV R 22 UF 250V 22 UF 100V 6.8 UF 50V 2200 UF 25V 0.001 UF 2KV R 0.001 UF 2KV R 2.2 UF 50V 0.22 UF 275V ECQUL 0.1 UF 275V ECQUL 470 UF 200V 0.0022UF 250V 0.001 UF 250V 0.0015UF 2KV R 0.001 UF 250V 220 UF 160V 2200 UF 16V 0.0022 UF 2KV R 0.001 UF 2KV B 2200 UF 25V 1000 UF 25V 1000 UF 25V MTZJ33B T-77 1SS133T-77 1SS133T-77 MTZJ5.1B T-77 SLR-342VCT32 MTZJ5.6B T-77
CAPACITORS
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
DIODES
DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,ZENER LED DIODE,ZENER
J2-1
27A45

Location No.
D402 D403 D404 D405 D406 D407 D408 D409 D410 D411 D414 D415 D416 D417 D419 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D514 D516 D517 D520 D523 D524 D525 D528 D601 D602 D604 D605 D606 D607 D608 D701 D702 D703 D704 D705 D706 D709 D801 D802 D803 D810 D811 D812
TSB P/N
BZ410043 BZ410019 BZ410020 BZ410063 BZ410021 BZ410063 AD302110 AD301980 BZ410019 BZ410063 BZ410043 BZ410043 BZ410006 BZ410006 BZ410006 BZ410062 BZ410062 BZ410062 BZ410062 AE006082 AD300731 BZ410006 BZ410066 AD300671 AD301980 AD300731 BZ410010 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 AD300671 BZ410006 BZ410094 BZ410021 BZ410006 BZ410058 AD300070 BZ410006 BZ410006 BZ410006 BZ410043 AD300070 AD300070 AD300070 AD300070 AD300070 AD300070 BZ410066 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 AE006067 AE006894 AD301983 BZ611117 BZ410088 AE002803 AD301988 AD301988 BZ611068 AE003081 AE003002 AD301988 AD301988
Reference No. DIODES

D2WT011E10 D97U03001B D97U05R11B D2WTAU02A0 D97U05R61B D2WTAU02A0 D2CF0715L0 D2CF2016L0 D97U03001B D2WTAU02A0 D2WT011E10 D2WT011E10 D1VT001330 D1VT001330 D1VT001330 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D28F0PRA60 D2WXN49370 D1VT001330 D97U06R21B D97U01801B D2CF2016L0 D2WXN49370 D28T21DQN9 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D97U01801B D1VT001330 D97U01501B D97U05R61B D1VT001330 D97U08R21B D97U01201B D1VT001330 D1VT001330 D1VT001330 D2WT011E10 D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U06R21B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 I56F07090B A3S2022015 I01FF58910 I03TD80410 0002E00610 I06FC1283A I0UF015010 I0UF015010 I01FF58290 I0FSP7808B I03FE76605 I0UF015010 I0UF015010 DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,RECTIFIER DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON
Description
11E1-EIC MTZJ30B T-77 MTZJ5.1B T-77 AU02A-EIC MTZJ5.6B T-77 AU02A-EIC ERD07-15L50 FE201-6L49 MTZJ30B T-77 AU02A-EIC 11E1-EIC 11E1-EIC 1SS133T-77 1SS133T-77 1SS133T-77 RM11C-EIC RM11C-EIC RM11C-EIC RM11C-EIC 30PRA60-FC 1N4937 1SS133T-77 MTZJ6.2B T-77 MTZJ18B T-77 FE201-6L49 1N4937 21DQ09N-TA2B1 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ18B T-77 1SS133T-77 MTZJ15B T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ8.2B T-77 MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 11E1-EIC MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ6.2B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 OEC7090B BR24L16FJ-WE2 AN5891SA-E1V LA78041 LTV-817M-VB M61283FP R70T MM1501XNRE MM1501XNRE AN5829S AN17808B LA76605M-TLM MM1501XNRE MM1501XNRE
! ! !
! ! ! ! ! !
! !
ICS
IC101 IC199 IC302 ! IC401 ! IC504 IC601 IC701 IC702 IC902 ! IC1001 IC1501 IC1502 IC1503 IC INIT DATA IC IC PHOTO COUPLER IC IC IC IC IC IC IC IC
J2-2
27A45

Location No.
Q101 Q103 Q402 Q405 Q408 Q409 Q410 Q411 Q502 Q503 Q504 Q505 Q507 Q508 Q509 Q512 Q514 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q611 Q614 Q709 Q711 Q712 Q801 Q802 Q803 Q804 Q805 Q806 Q901 Q902 Q1001 Q1503 Q1504 Q1507 Q1508
TSB P/N
BZ510109 BZ510109 BZ510097 BZ510040 BZ510073 BZ510073 BZ510110 BZ510109 BZ510098 BZ510005 BZ510069 BZ510011 BZ510069 BZ510077 BZ510069 BZ510004 BZ510070 BZ510105 BZ510105 BZ510109 BZ510105 BZ510109 BZ510105 BZ510070 BZ510105 BZ510108 BZ510108 BZ510109 BZ510109 BZ510100 BZ510100 BZ510100 BZ510091 BZ510091 BZ510091 BZ510108 BZ510108 BZ510068 BZ510109 BZ510109 BZ510109 BZ510109 BZ310041 BZ310187 AD301606 AD301124 AD301607 BZ310041 BZ310041 AD301417 AD301417 AD300613 BZ310041 AD300613 AD300613 BZ310183 BZ310189 AD301034 AE002759 AE006074 AE002759 AE002761 AE004756 AE004758 AE004757 AE002759 AD301356
Reference No. TRANSISTORS

TCAA3875SY TCAA3875SY TCAT03227Y TDUU024990 TAATA12660 TAATA12660 TC30041590 TCAA3875SY T220033260 TA3T1371A0 TCATC31980 TC3T029090 TCATC31980 TAAT012714 TCATC31980 TA3T016240 TCAT032034 TCAT03209Y TCAT03209Y TCAA3875SY TCAT03209Y TCAA3875SY TCAT03209Y TCAT032034 TCAT03209Y TAAA1504SY TAAA1504SY TCAA3875SY TCAA3875SY TCATC3199Y TCATC3199Y TCATC3199Y TCA0042170 TCA0042170 TCA0042170 TAAA1504SY TAAA1504SY TNAAJ05003 TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY 02167F101J 022100034A 02DK000058 029T000101 028R270010 02167F101J 02167F101J 02167F221J 02167F221J 02167F150J 02167F101J 02167F150J 02167F150J 021LA6220J 0450190161 048140066S 060J431020 063Q700011 060J431020 060J411032 060J401104 060J401106 060J401105 060J431020 066F130020
Description
KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3227_Y-AT 2SD2499(LB0EC1) KTA1266-AT(Y,GR) KTA1266-AT(Y,GR) 2SC4159(D,E) KTC3875S_Y_RTK 2SK3326(2) 2SA1371(D,E)-AE KTC3198-AT(Y,GR) 2SC2909(S,T)-AA KTC3198-AT(Y,GR) KTA1271_Y-AT KTC3198-AT(Y,GR) 2SA1624-AA KTC3203_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3203_Y-AT KTC3209_Y-AT KTA1504S_Y_RTK KTA1504S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3199_Y-AT KTC3199_Y-AT KTC3199_Y-AT KTC4217(O,Y) KTC4217(O,Y) KTC4217(O,Y) KTA1504S_Y_RTK KTA1504S_Y_RTK KRC111SRTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK 100 UH ELH5L4132N 02DK000058 2R2A752F28Y 8R270010 100 UH 100 UH 220 UH 220 UH 15 UH 100 UH 15 UH 15 UH 22 UH ETH19Y203AY 8140066S MSP-213V2-432_NI_LF YKF51-5503N MSP-213V2-432_NI_LF MSP-213V1-652_NI_LF MTJ-032-03A-30FE MTJ-032-03A-32FE MTJ-032-03A-31FE MSP-213V2-432_NI_LF ISHS53S
! !
! ! ! ! ! ! !
! ! ! ! ! !
TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON FET TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COIL COIL,LINEARITY COIL,CHOKE COIL,LINE FILTER COIL,DEGAUSS COIL COIL COIL COIL COIL COIL COIL COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
COILS &TRANSFORMERS
L301 L402 L403 ! L501 ! L503 L901 L1501 L1502 L1503 L1505 L1508 L1510 L1511 L1512 T401 ! T501 J701 J702 J703 J704 J705 J706 J707 J708 ! J801
JACKS
RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY,TUBE
J2-3
27A45

Location No.
SW101 SW102 SW103 SW104 SW105 VR401 VR502 PCB010 PCB110 B403 B405 B501 B504 BT001 BT002 CD501 CD801 CD802 CD803 CP101 CP401 CP501 CP502 CP507 CP508 CP803 CP1001 CP801A CP801B CP802A CP802B EL001 EL002 F501 FB401 FH501 FH502 OS101 RY501 SP1001 TH501 TM101 TU001 V801 X101 X602 RESISTOR RC................... CAPACITORS CC................... CE................... CP................... CPP.................. CPL.................. CMP................... CMPL................ CMPP................ CERAMIC CAPACITOR ALUMI ELECTROLYTIC CAPACITOR POLYESTER CAPACITOR POLYPROPYLENE CAPACITOR PLASTIC CAPACITOR METAL POLYESTER CAPACITOR METAL PLASTIC CAPACITOR METAL POLYPROPYLENE CAPACITOR CARBON RESISTOR
TSB P/N
BZ612010 BZ612010 BZ612010 BZ612010 BZ612010 BZ210218 BZ210101 AE006895 AE006118 BZ310129 BZ310129 BZ310045 BZ310121 AE005640 AE005640 AE006077 BZ614385 AD302116 AE005894 BZ614102 AE006075 BZ614176 BZ614283 BZ614016 BZ614016 BZ614269 AD301045 BZ614276 BZ614276 AD301997 AD301997 BZ614044 BZ614043 BZ614422 AE003347 AE002634 AE002634 AD301048 AE006070 AE006119 BZ410079 AE000622 AE006069 AD301614 AD302002 BZ613004
Reference No. SWITCHES

0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 V1K63H3BTE V1163H4BTC A3S2022010 A3S2012110 024HT03564 024HT03564 024AT03481 024HT03553 141R004016 141R004016 1209615904 WCL6838038 WEL6852038 06C3823005 0694270139 069X460109 069S320419 069S420110 069W01001A 069W01001A 069S320010 069S140419 067U005049 067U005049 067U007029 067U007029 124120301A 124116281A 081PC6R305 043227016F 06710T0009 06710T0009 0773071001 0560X20118 070Y435017 DF5EL3R0A0 076R0GW010 0163300018 0981270B01 100CT8R005 100CT3R505 SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT VOLUME,SEMI FIXED VOLUME,SEMI FIXED PCB ASS'Y PCB ASS'Y
Description
EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R NVG6TLTAB222 EVNCYAA03BE4 CMD016A CCD010A W4BRH3.5X6X1.0 W4BRH3.5X6X1.0 BL02RN1-R62T2 W5RH3.5X5X1.0 GR03X-SP2 GR03X-SP2 9615904 WG26 5C GRAY 380MM WG26 7C GRAY 520MM C3823005 173979-7 B06B-DVS-L (LF) A3963WV2-3PD A1561WV2-2P 003P-2100 003P-2100 A2361WV2-2P A2502WV2-4P B2013H02-5P B2013H02-5P B2013H02-7P B2013H02-7P XRY20X30BD XRY16X28BD 51MS063L FJN27A003_M EYF-52BCY EYF-52BCY RPM7138-WH5 G5PA-1-SA(WEC) S0509F12A-F ZPB45BL3R0A R25-1939 115-V-KA35ARB M68LWF088X50 HC-49/U-S HC-49/U
VARIABLE RESISTORS P.C.BOARD ASSEMBLIES MISCELLANEOUS

CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS BATTERY,MANGAN BATTERY,MANGAN CORD,AC BUSH FLAT CABLE AWM2468 A FLAT CABLE AWM2468 A CORD,CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER WIRE HOLDER WIRE HOLDER EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER DEGAUSS ELEMENT TRANSMITTER RF UNIT CRT W/DY CRYSTAL CRYSTAL
! ! !
! !
! ! ! ! !
J2-4
27A45

Location No.
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! R409 R410 R419 R426 R429 R434 R436 R438 R439 R441 R452 R457 R459 R461 R500 R501 R502 R506 R507 R517 R520 R527 R533 R541 R542 R543 R601 R602 R629 R649 R803 R805 R807 R1014 C156 C408 C412 C413 C418 C420 C421 C425 C426 C430 C442 C501 C502 C503 C504 C505 C506 C507 C508 C513 C517 C519 C521 C527 C535 C802 C1003 C1004 C1009 D001 D104 D105 D106 D109 D113
TSB P/N
AE001783 AD302107 AD300784 BZ210030 AE000145 AD300421 BZ210023 BZ210022 BZ210003 BZ210231 AD301385 BZ210122 AD301595 AE000849 BZ210080 AD301596 BZ210249 BZ210162 AE002597 AD302108 BZ210206 BZ210149 AE002872 AE005735 BZ210248 BZ210180 AE006340 AD301975 AE001801 AD301975 BZ210050 BZ210050 BZ210050 AE006741 AE004040 BZ110032 AD301599 AD301977 AE001019 AD300723 AD301600 BZ110202 BZ110225 BZ110195 AE006084 BZ210176 BZ110202 BZ110202 AD301729 BZ110025 BZ110035 BZ110012 BZ110222 AD301026 BZ110191 AD301026 AE006083 BZ110119 BZ110201 BZ110247 BZ210176 BZ110053 BZ110053 BZ410037 BZ410006 BZ410006 BZ410020 BZ410054 BZ410021
Reference No. RESISTORS

R803R9102J R3X18A470J R3X1811R2J R4X5T4472F R002T2561J R5X2CF1R8J R4X5T4183F R6558A1R2J R3K181102J R4X5T6153F R3X18A391J R002T4472J R65582010J R803R9152J R0G3K2275K R5X2AE010J R3X28A331J R002T4682J R00202823J R3X28BR39J R002T2155J R3X18AR68J R803R9271J R63881R22J R3X181R15J R002T2102J R3X181150J R3X28B120J R803R9682J R3X28B120J R3X18A123J R3X18A123J R3X18A123J R00204821J P6M900105J E5EZF3102M P4N8FJ272H E0ELF4102M P4J7F3434J P4N8FJ153H P3N1F5223J C0PLRR713K E5EZFD220M E02LU8220M E736F56R8M E02LF3222M C0PLRR713K C0PLRR713K E02LU52R2M P2122B224M P2122B104M E51CGC471M CD39E0MH3M CD39E0M13M C03L0R7E3K CD39E0M13M E61DFB221M E02LF2222M C0PLRR7H3K C0JBB0713K E02LF3222M E02LF3102M E02LF3102M D97U03301B D1VT001330 D1VT001330 D97U05R11B 0021721150 D97U05R61B RC R,METAL OXIDE R,METAL OXIDE R,METAL RC R,CEMENT R,METAL R,FUSE R,METAL OXIDE R,METAL R,METAL OXIDE RC R,FUSE RC RC R,CEMENT R,METAL OXIDE RC RC R,METAL OXIDE RC R,METAL OXIDE RC R,FUSE R,METAL OXIDE RC R,METAL OXIDE R,METAL OXIDE RC R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE RC
Description
1K OHM 1/16W 47 OHM 2W 1.2 OHM 1W 4.7K OHM 1/4W 560 OHM 1/2W 1.8 OHM 10W 18K OHM 1/4W 1.2 OHM 2W 1K OHM 1W 15K OHM 1/6W 390 OHM 2W 4.7K OHM 1/4W 1 OHM 1/2W 1.5K OHM 1/16W 2.7M OHM 1/2W 1 OHM 7W 330 OHM 2W 6.8K OHM 1/4W 82K OHM 1/2W 0.39 OHM 3W 1.5M OHM 1/2W 0.68 OHM 2W 270 OHM 1/16W 0.22 OHM 1W 0.15 OHM 1W 1K OHM 1/2W 15 OHM 1W 12 OHM 3W 6.8K OHM 1/16W 12 OHM 3W 12K OHM 2W 12K OHM 2W 12K OHM 2W 820 OHM 1/4W 1 UF 50V TF 1000 UF 25V 0.0027UF 1.25KV 1000 UF 35V 0.43 UF 250V PMS 0.015 UF 1.25KV 0.022 UF 630V 0.001 UF 2KV R 22 UF 250V 22 UF 100V 6.8 UF 50V 2200 UF 25V 0.001 UF 2KV R 0.001 UF 2KV R 2.2 UF 50V 0.22 UF 275V ECQUL 0.1 UF 275V ECQUL 470 UF 200V 0.0022UF 250V 0.001 UF 250V 0.0015UF 2KV R 0.001 UF 250V 220 UF 160V 2200 UF 16V 0.0022 UF 2KV R 0.001 UF 2KV B 2200 UF 25V 1000 UF 25V 1000 UF 25V MTZJ33B T-77 1SS133T-77 1SS133T-77 MTZJ5.1B T-77 SLR-342VCT32 MTZJ5.6B T-77
CAPACITORS
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! CMPL CE CMPP CE CMPP CMPP CPP CC CE CE CE CE CC CC CE CMP CMP CE CC CC CC CC CE CE CC CC CE CE CE
DIODES
DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,ZENER LED DIODE,ZENER
J2-5
27A45C

D402 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EIC
Location No.
D403 D404 D405 D406 D407 D408 D409 D410 D411 D414 D415 D416 D417 D419 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D514 D516 D517 D520 D523 D524 D525 D528 D601 D602 D604 D605 D606 D607 D608 D701 D702 D703 D704 D705 D706 D709 D801 D802 D803 D810 D811 D812
TSB P/N
BZ410019 BZ410020 BZ410063 BZ410021 BZ410063 AD302110 AD301980 BZ410019 BZ410063 BZ410043 BZ410043 BZ410006 BZ410006 BZ410006 BZ410062 BZ410062 BZ410062 BZ410062 AE006082 AD300731 BZ410006 BZ410066 AD300671 AD301980 AD300731 BZ410010 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 AD300671 BZ410006 BZ410094 BZ410021 BZ410006 BZ410058 AD300070 BZ410006 BZ410006 BZ410006 BZ410043 AD300070 AD300070 AD300070 AD300070 AD300070 AD300070 BZ410066 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 AE006067 AE006116 AD301983 BZ611117 BZ410088 AE002803 AD301988 AD301988 BZ611068 AE003081 AE003002 AD301988 AD301988
Reference No. DIODES

D97U03001B D97U05R11B D2WTAU02A0 D97U05R61B D2WTAU02A0 D2CF0715L0 D2CF2016L0 D97U03001B D2WTAU02A0 D2WT011E10 D2WT011E10 D1VT001330 D1VT001330 D1VT001330 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D28F0PRA60 D2WXN49370 D1VT001330 D97U06R21B D97U01801B D2CF2016L0 D2WXN49370 D28T21DQN9 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D97U01801B D1VT001330 D97U01501B D97U05R61B D1VT001330 D97U08R21B D97U01201B D1VT001330 D1VT001330 D1VT001330 D2WT011E10 D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U06R21B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 I56F07090B A3S2012015 I01FF58910 I03TD80410 0002E00610 I06FC1283A I0UF015010 I0UF015010 I01FF58290 I0FSP7808B I03FE76605 I0UF015010 I0UF015010 DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,RECTIFIER DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON
Description
MTZJ30B T-77 MTZJ5.1B T-77 AU02A-EIC MTZJ5.6B T-77 AU02A-EIC ERD07-15L50 FE201-6L49 MTZJ30B T-77 AU02A-EIC 11E1-EIC 11E1-EIC 1SS133T-77 1SS133T-77 1SS133T-77 RM11C-EIC RM11C-EIC RM11C-EIC RM11C-EIC 30PRA60-FC 1N4937 1SS133T-77 MTZJ6.2B T-77 MTZJ18B T-77 FE201-6L49 1N4937 21DQ09N-TA2B1 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ18B T-77 1SS133T-77 MTZJ15B T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ8.2B T-77 MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 11E1-EIC MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ6.2B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 OEC7090B BR24L16FJ-WE2 AN5891SA-E1V LA78041 LTV-817M-VB M61283FP R70T MM1501XNRE MM1501XNRE AN5829S AN17808B LA76605M-TLM MM1501XNRE MM1501XNRE
! !
! ! ! ! ! !
! !
ICS
IC101 IC199 IC302 ! IC401 ! IC504 IC601 IC701 IC702 IC902 ! IC1001 IC1501 IC1502 IC1503 IC INIT DATA IC IC PHOTO COUPLER IC IC IC IC IC IC IC IC
J2-6
27A45C

Location No.
Q101 Q103 Q402 Q405 Q408 Q409 Q410 Q411 Q502 Q503 Q504 Q505 Q507 Q508 Q509 Q512 Q514 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q611 Q614 Q709 Q711 Q712 Q801 Q802 Q803 Q804 Q805 Q806 Q901 Q902 Q1001 Q1503 Q1504 Q1507 Q1508
TSB P/N
BZ510109 BZ510109 BZ510097 BZ510040 BZ510073 BZ510073 BZ510110 BZ510109 BZ510098 BZ510005 BZ510069 BZ510011 BZ510069 BZ510077 BZ510069 BZ510004 BZ510070 BZ510105 BZ510105 BZ510109 BZ510105 BZ510109 BZ510105 BZ510070 BZ510105 BZ510108 BZ510108 BZ510109 BZ510109 BZ510100 BZ510100 BZ510100 BZ510091 BZ510091 BZ510091 BZ510108 BZ510108 BZ510068 BZ510109 BZ510109 BZ510109 BZ510109 BZ310041 BZ310187 AD301606 AD301124 AD301607 BZ310041 BZ310041 AD301417 AD301417 AD300613 BZ310041 AD300613 AD300613 BZ310183 BZ310189 AD301034 AE002759 AE006074 AE002759 AE002761 AE004756 AE004758 AE004757 AE002759 AD301356
Reference No. TRANSISTORS

TCAA3875SY TCAA3875SY TCAT03227Y TDUU024990 TAATA12660 TAATA12660 TC30041590 TCAA3875SY T220033260 TA3T1371A0 TCATC31980 TC3T029090 TCATC31980 TAAT012714 TCATC31980 TA3T016240 TCAT032034 TCAT03209Y TCAT03209Y TCAA3875SY TCAT03209Y TCAA3875SY TCAT03209Y TCAT032034 TCAT03209Y TAAA1504SY TAAA1504SY TCAA3875SY TCAA3875SY TCATC3199Y TCATC3199Y TCATC3199Y TCA0042170 TCA0042170 TCA0042170 TAAA1504SY TAAA1504SY TNAAJ05003 TCAA3875SY TCAA3875SY TCAA3875SY TCAA3875SY 02167F101J 022100034A 02DK000058 029T000101 028R270010 02167F101J 02167F101J 02167F221J 02167F221J 02167F150J 02167F101J 02167F150J 02167F150J 021LA6220J 0450190161 048140066S 060J431020 063Q700011 060J431020 060J411032 060J401104 060J401106 060J401105 060J431020 066F130020
Description
KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3227_Y-AT 2SD2499(LB0EC1) KTA1266-AT(Y,GR) KTA1266-AT(Y,GR) 2SC4159(D,E) KTC3875S_Y_RTK 2SK3326(2) 2SA1371(D,E)-AE KTC3198-AT(Y,GR) 2SC2909(S,T)-AA KTC3198-AT(Y,GR) KTA1271_Y-AT KTC3198-AT(Y,GR) 2SA1624-AA KTC3203_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3875S_Y_RTK KTC3209_Y-AT KTC3203_Y-AT KTC3209_Y-AT KTA1504S_Y_RTK KTA1504S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3199_Y-AT KTC3199_Y-AT KTC3199_Y-AT KTC4217(O,Y) KTC4217(O,Y) KTC4217(O,Y) KTA1504S_Y_RTK KTA1504S_Y_RTK KRC111SRTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK 100 UH ELH5L4132N 02DK000058 2R2A752F28Y 8R270010 100 UH 100 UH 220 UH 220 UH 15 UH 100 UH 15 UH 15 UH 22 UH ETH19Y203AY 8140066S MSP-213V2-432_NI_LF YKF51-5503N MSP-213V2-432_NI_LF MSP-213V1-652_NI_LF MTJ-032-03A-30FE MTJ-032-03A-32FE MTJ-032-03A-31FE MSP-213V2-432_NI_LF ISHS53S
! !
! ! ! ! ! ! !
! ! ! ! ! !
TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON FET TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COIL COIL,LINEARITY COIL,CHOKE COIL,LINE FILTER COIL,DEGAUSS COIL COIL COIL COIL COIL COIL COIL COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
COILS &TRANSFORMERS
L301 L402 L403 ! L501 ! L503 L901 L1501 L1502 L1503 L1505 L1508 L1510 L1511 L1512 T401 ! T501 J701 J702 J703 J704 J705 J706 J707 J708 ! J801
JACKS
RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY,TUBE
J2-7
27A45C

Location No.
SW101 SW102 SW103 SW104 SW105 VR401 VR502 PCB010 PCB110 B403 B405 B501 B504 BT001 BT002 CD501 CD801 CD802 CD803 CP101 CP401 CP501 CP502 CP507 CP508 CP803 CP1001 CP801A CP801B CP802A CP802B EL001 EL002 F501 FB401 FH501 FH502 OS101 RY501 SP1001 TH501 TM101 TU001 V801 X101 X602 RESISTOR RC................... CAPACITORS CC................... CE................... CP................... CPP.................. CPL.................. CMP................... CMPL................ CMPP................ CERAMIC CAPACITOR ALUMI ELECTROLYTIC CAPACITOR POLYESTER CAPACITOR POLYPROPYLENE CAPACITOR PLASTIC CAPACITOR METAL POLYESTER CAPACITOR METAL PLASTIC CAPACITOR METAL POLYPROPYLENE CAPACITOR CARBON RESISTOR
TSB P/N
BZ612010 BZ612010 BZ612010 BZ612010 BZ612010 BZ210218 BZ210101 AE006117 AE006118 BZ310129 BZ310129 BZ310045 BZ310121 AE005640 AE005640 AE006077 BZ614385 AD302116 AE005894 BZ614102 AE006075 BZ614176 BZ614283 BZ614016 BZ614016 BZ614269 AD301045 BZ614276 BZ614276 AD301997 AD301997 BZ614044 BZ614043 BZ614422 AE003347 AE002634 AE002634 AD301048 AE006070 AE006119 BZ410079 AE000622 AE006069 AD301614 AD302002 BZ613004
Reference No. SWITCHES

0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 V1K63H3BTE V1163H4BTC A3S2012010 A3S2012110 024HT03564 024HT03564 024AT03481 024HT03553 141R004016 141R004016 1209615904 WCL6838038 WEL6852038 06C3823005 0694270139 069X460109 069S320419 069S420110 069W01001A 069W01001A 069S320010 069S140419 067U005049 067U005049 067U007029 067U007029 124120301A 124116281A 081PC6R305 043227016F 06710T0009 06710T0009 0773071001 0560X20118 070Y435017 DF5EL3R0A0 076R0GW010 0163300018 0981270B01 100CT8R005 100CT3R505 SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT VOLUME,SEMI FIXED VOLUME,SEMI FIXED PCB ASS'Y PCB ASS'Y
Description
EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R NVG6TLTAB222 EVNCYAA03BE4 CMD016A CCD010A W4BRH3.5X6X1.0 W4BRH3.5X6X1.0 BL02RN1-R62T2 W5RH3.5X5X1.0 GR03X-SP2 GR03X-SP2 9615904 WG26 5C GRAY 380MM WG26 7C GRAY 520MM C3823005 173979-7 B06B-DVS-L (LF) A3963WV2-3PD A1561WV2-2P 003P-2100 003P-2100 A2361WV2-2P A2502WV2-4P B2013H02-5P B2013H02-5P B2013H02-7P B2013H02-7P XRY20X30BD XRY16X28BD 51MS063L FJN27A003_M EYF-52BCY EYF-52BCY RPM7138-WH5 G5PA-1-SA(WEC) S0509F12A-F ZPB45BL3R0A R25-1939 115-V-KA35ARB M68LWF088X50 HC-49/U-S HC-49/U
VARIABLE RESISTORS P.C.BOARD ASSEMBLIES MISCELLANEOUS

CORE,BEADS CORE,BEADS CORE,BEADS CORE,BEADS BATTERY,MANGAN BATTERY,MANGAN CORD,AC BUSH FLAT CABLE AWM2468 A FLAT CABLE AWM2468 A CORD,CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER WIRE HOLDER WIRE HOLDER EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER DEGAUSS ELEMENT TRANSMITTER RF UNIT CRT W/DY CRYSTAL CRYSTAL
! ! !
! !
! ! ! ! !
J2-8
27A45C
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN

A 45

Uploaded by

Copyright:

Available Formats

A 45

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

A 45

Uploaded by

Copyright:

Available Formats

FILE NO.

050-200505 (MFRS VERSION A)

DOCUMENT CREATED IN JAPAN, February, 2005

SERVICING NOTICES ON CHECKING

2. AVOID AN ELECTRIC SHOCK

3. USE THE DESIGNATED PARTS

7. PERFORM A SAFETY CHECK AFTER SERVICING

5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE

External exposure metal: Antenna terminal Headphone jack

HOW TO ORDER PARTS

ABOUT LEAD FREE SOLDER (PbF)

Color System Speaker Position Size Impedance MAX 10%(Typical)

Sound Output NTSC3.58+4.43 /PAL60Hz Broadcasting System Tuner and Receive CH

System Destination CH Coverage Picture(FP) Sound(FS) FP-FS

Temperature Operating Humidity

120 Min 10 Min Yes -No Min Sec

Multi Brand Keys

No No No No No No No No No No No No Yes UM4 size x 2 No No No Yes No No No

G-14 G-15 G-16

Set Size Weight Carton Master Carton

Color System Speaker Position Size Impedance MAX 10%(Typical)

Sound Output NTSC3.58+4.43 /PAL60Hz Broadcasting System Tuner and Receive CH

System Destination CH Coverage Picture(FP) Sound(FS) FP-FS

Temperature Operating Humidity

120 Min 10 Min Yes -No Min Sec

Multi Brand Keys

No No No No No No No No No No No No Yes UM4 size x 2 No No No No No No No

G-14 G-15 G-16

Set Size Weight Carton Master Carton

CRT Support Alligator Clip Fig. 1-4

GND on the CRT

CRT CRT Support Fig. 1-2

Support Fig. 1-5

Masking Tape (Cotton Tape)

Blower type IC desoldering machine

Braided Shield Wire

Thin-tip Soldering Iron

Supply soldering from upper position to lower position

Braided Shield Wire

Fig. 2-7 B2-2 27A45/27A45C

SERVICE MODE LIST

VOL. (-) MIN

CONFIRMATION OF HOURS USED

WHEN REPLACING EEPROM (MEMORY) IC

Fig. 1-2 D-1 27A45/27A45C

R G B UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT Fig. 3-2-a

WEDGE WEDGE POSITION Fig. 3-2-b

PURITY MAGNETS 6 POLE MAGNETS 4 POLE MAGNETS Fig. 3-1

CD801 CRT CD802

FB401 CP401 TP003 W003 TU001 VR502 VR401

SPEAKER CP802A L503 CP502 CRT

A/V OUT J708

COMB FILTER IC IC1501 LA76605M-TLM

CHROMA IC IC601 M61283FP R70T

VIDEO SW(Y) IC IC1502 MM1501XNRE S-JACK J702 LINE1(REAR) J701

VIDEO SW(C) IC IC1503 MM1501XNRE

FRONT -VIDEO J705

CVBS1 CVBS2 CVBS3

MICON IC101 OEC7090B

53 CVBS4 48 Y IN(YUV) 44 U IN(YUV) 40 V IN(YUV)