Writing coursework can be quite a challenge, especially when it comes to subjects like GCSE

Resistant Materials. It requires a combination of theoretical knowledge and practical skills, making it
a task that demands attention to detail and creativity. Many students find it overwhelming to balance
the research, planning, and actual writing.

If you're feeling the pressure, it might be worth considering getting some assistance. ⇒
HelpWriting.net ⇔ is a platform that connects students with experienced writers who can provide
guidance and support throughout the coursework process. Having an extra pair of knowledgeable
eyes can make a significant difference, helping you navigate through the intricacies of the subject
and ensuring your coursework meets the required standards.

Remember, seeking help doesn't mean you're not capable; it's a smart move to enhance your learning
experience. So, if you're feeling stuck or stressed, check out ⇒ HelpWriting.net ⇔ for a helping
hand in crafting your GCSE Resistant Materials coursework. It might just be the support you need to
excel in your academic journey.
Knock down fittings (KD) Many DIY and furniture stores sell their products flat packed in
cardboard boxes. We are coursework of all the rules, which are to be maintained for creating term
helps. The process was that it would cut 6 mil into the wood and when it has done that for all of the
lines, it would then go down another 6 mil to complete the process. It has one chain running from
the motor shaft gear to the big gear on the wheel. Kidney dialysis 95. Kidney dialysis In the absence
of a suitable donor kidney, the alternative solution is for the patient to be hooked-up to a dialysis
machine every 2 - 3 days. Nathaniel Olson GCSE Resistant Materials Top Piece and the Man The top
piece will be added onto the top of car, making the car stronger and more durable. Water moves into
the cells by osmosis and could cause them to burst. 97. Blood concentration too high The
hypothalamus senses too little water in the blood. Interview with Chris Parker I had an interview
with Chris Parker, a Director at Inspired Cycle Engineering, who mentors the Greenpower club at
Penair School. Skip to content Essayped — Essay writing service Quality papers at the help prices. I
chose this car because it was the most practical and most developed out of my three ideas. The joints
needs strengthening, so I am going to put timber blocks in ever corner inside the cockpit and around
the battery box area. We used steel because it’s very strong and versatile. Nathaniel Olson GCSE
Resistant Materials Task Analysis Materials Wood Organic, non. Is done by choosing parents with
the required traits. A wide range of excercises about resistant materials, systems approach, Orange
and blue banner with text GCSE Bitesize on left and the Bitesize fish on right. Page Outline. Page
Analysis. CRITERION 1. Recognition of Problem. Blood Cells 46. Tissue exchange 47. The
lymphatic system Transports excess fluid from the tissues. Nitrogen Cycle 66. Food Production and
farming methods Monoculture. If I was to redesign the car again, I would make the chassis 50mm
narrower. The track is very big and has big corners that does not require a great degree of turning.
Hey all, the deadline for my resistant materials coursework is really It s for gcse but it helps a bit you
just need to write lods and lods more. I have received good feedback saying the car is very good
overall. Design Section (B) EdExcel. Designing. Range of skills: 2D 3D (isometric, perspective)
CAD. Sheet 1. Layout. Design Brief. Specification. Inspiration. Brief and Specification. All of the
changes and development that I have done are from slide 27 to 37. In my computer model, I need to
see whether a person would fit inside the car so I downloaded an ergonome off the internet and used
him to evaluated my model and see if it works. As the shoulders are a lot wider then the hips and
legs, I make the space around the legs a lot thinner. The big disadvantage of this car is that it’s not
very aerodynamic which is vitally important in in Greenpower racing. Unit 2 Knowledge and
Understanding of Resistant Materials Technology 24 Topic 1 Materials and components 25.
Although aerodynamics is important, keeping the weight low is worth doing. The motor and batteries
would be mounted on a partition that hangs from the posts.
Meet the deadline. Suggested maximum five hours (three in class, 2 out of class). Collection of Data.
Hypothesis. Data Handling GCSE coursework. Commercial Catering: Hotels, restaurants, clubs,
wine bars and pubs. The book was exactly as described and I would definitely buy from this seller
again. Manufacturing Processes: Sand paper, square files, electric drills, Router. Also this would be
more attractive to the pupils that come from feeder schools which have been participating in the
Goblins. Heat is lost by convection, conduction and radiation. I used a solvent based garage floor
paint because it’s a tough, waterproof paint that will hopefully last for a reasonably long time.
Radiation and certain chemicals such as cigarette smoke can cause mutations. What is a HEALTHY,
ACTIVE LIFESTYLE? “A lifestyle that contributes positively to physical, mental and social
wellbeing and includes regular exercise and physical activity”. This car has a lot more steering than is
required in Greenpower racing. Batch One off Continuous Mass 33 Resistant Materials Revision
Quiz Which wood joint is this. Also it’s very similar to the Penryn’sGreenpower car steering layout.
Although aerodynamics is important, keeping the weight low is worth doing. Our customer service
team will review your report and will be in touch. ?5.00 (no rating) 0 reviews BUY NOW Save for
later ?5.00 (no rating) 0 reviews BUY NOW Save for later Last updated 2 October 2017 Share this
Share through email Share through twitter Share through linkedin Share through facebook Share
through pinterest Ktreen's Shop 4.00 11 reviews Not the right resource. What processes could you
use to make the real thing. The only concern is that the way that the glue works, it reacts with
moisture and therefore it foams out of the joints. Abbie Sidaway. What different techniques could I
use on my product. Name Candidate Number Walkden High School: 33383 OVERALL
DEADLINE: Feb 14 th 2014. I used my research to determine what was needed for my car and
what it didn’t need. Returns accepted. Location: NY, United States Returns: 30 days returns.
Aluminium b. Iron c. Stainless Steel d. Brass 20 Resistant Materials Revision Quiz Which metal
would normally used to make this product? a. Brass b. Stainless Steel c. Aluminium d. Iron 21
Resistant Materials Revision Quiz Which metal would normally used to make this product
(Blacksmiths Anvil)? a. Initially I intended to design for 1 month but in the end it took 3. What
processes could you use to make the real thing. If I was to redesign the car again, I would make the
chassis 50mm narrower. The car has a 11 metres turning circle so it’s more manoeuvrable than a
ordinary car. Get this resource as part of a bundle and save up to 61% A bundle is a package of
resources grouped together to teach a particular topic, or a series of lessons, in one place. It has one
chain running from the motor shaft gear to the big gear on the wheel. I changed the steering layout as
there wasn’t going to be enough room for all the linkages between the handle and the wheel. As the
shoulders are a lot wider then the hips and legs, I make the space around the legs a lot thinner.
GCSE Resistant Materials - Major Project: Initial ideas. Some filing and sanding is also required to
make sure everything fits together. Sustainability means that any waste wood from a workshop is
thrown into a bin and sent off to an incinerator. If it gets too cold the rate of photosynthesis will
slow right down; equally, plants cease to be able to photosynthesise if it gets too hot. Our customer
service team will review your report and will be in touch. ?3.50 (no rating) 0 reviews BUY NOW
Save for later ?3.50 (no rating) 0 reviews BUY NOW Save for later Last updated 2 May 2018 Share
this Share through email Share through twitter Share through linkedin Share through facebook Share
through pinterest MIK Ed 4.53 455 reviews Not the right resource. What happens in a race is that the
car travels over 1000 decent size bumps, even on a race track, during the 4 hours of racing. Cystic
fibrosis is caused by a mutation in the DNA. Then I had to prepare the plates that will be welded to
the cross axle as on their own, there is no way the axle can be attached to the car securely. GRP 23
Resistant Materials Revision Quiz Which plastic would normally be used to make this product? a.
LDPE b. HDPE c. Urea Formaldehyde d. I learnt that it was going to take longer than I had
expected for me to design the car. Assimilation All digested glucose and amino acids pass into the
liver in the Hepatic Portal Vein. It also saves weight by about 2kgs Doubler piece is placed where the
motor is mounted. There is no seat in this car because there is no space for it. This resource hasn't
been reviewed yet To ensure quality for our reviews, only customers who have purchased this
resource can review it Report this resource to let us know if it violates our terms and conditions.
Damage cause them to clump and they begin the conversion of soluble fibrinogen (blood protein)
into insoluble fibrin which meshes over the wound and traps red cells. The steering system need to be
changed as they would preferred side sticks to a handlebar. It is sustainable because it is made from
commercially forested wood and has little waste. If we put the battery at the front of the car, it
would make the handling horrible. An easily handled car will be quicker and cause less driver
fatigue. This reduces the space inside the chest and pushes air out of the lungs. 20. Breathing Rate
and Depth Rate - how many breaths per minute. Competence Performance Creativity Healthy, Active
Lifestyles. Mutations Change in the DNA of an organism caused by an error when it is copied. The
body shape is crucial in the performance of the car, so the body needs to be long, thin and low in
order for the car to cut through the air efficiently. A wide range of excercises about resistant
materials, systems approach, Orange and blue banner with text GCSE Bitesize on left and the
Bitesize fish on right. Steering is something that has to be considered with the shape of the body.
Write a review Update existing review Submit review Cancel It's good to leave some feedback. After
all of the wood work was done except the top piece, I got on with the painting of the car as it
needed to be waterproof otherwise it will warp and affect the car’s performance in wet weather.
Hormones Proteins that are chemical messengers in the body. The reason for the triangle shape is that
it’s a good shape to support the forces the car can subject to during the race, the hole are there for
making it lighter. Knowledge, skills and understanding developed during GCSE Design and
Technology: Resistant Materials - Unit 2 (4560), for exams from June 2010.
Evaporation of water from a surface removes heat. 84. Keeping Cool Vasodilation, more blood flows
nearer the skin and heat is lost. Nathaniel Olson GCSE Resistant Materials Top Piece and the Man
The top piece will be added onto the top of car, making the car stronger and more durable. A steering
system that requires a lot of room to build or to operate can increase the size of the car. Nathaniel
Olson GCSE Resistant Materials Greenpower Regulations 1 Batteries T2.6. Batteries must be
separated from the driver by a bulkhead, or contained in a rigid, covered, ventilated box, which must
not be able to short circuit battery terminals. It is also about how ready you are in body and mind to
perform them. It is sitting on rails so when the driver gets out, they slide the battery box out and
change the batteries. Make sure you know key terms Make sure you know: features, how they are
formed, the effect they cause, advantages and disadvantages to human life. It might be better to
construct a coffin-like box from several panels that would allow some control over the final shape,
especially if the box is going to be the outside skin of the car (aerodynamic shape is very important).
Feedback from other people Ask a minimum of 3 people, including the client. The tabs that controls
the steering wasn’t needed on the front kingposts as it would be moved. The top picture shows the 2
batteries and the motor in the car because I wanted to test the strength of the chassis with the
majority of the parts and myself in it. I chopped them off with an angle grinder with supervision.
Sustainability means that when you produce a product it will create a lasting negative effect on the
environment. GCSE Resistant Materials - Major Project: Initial ideas. Includes Wood, Manufactured
Boards, Metals, Plastics, Composite Materials, Ceramics, Smart Materials and Material Finishes. Hey
all, the deadline for my resistant materials coursework is really It s for gcse but it helps a bit you just
need to write lods and lods more. The pupils that are interested in engineering and racing need a kit-
car that is competitive, because the current kit-car that is being supplied by Greenpower is
uncompetitive in most cases and extremely heavy. Very little preparation needed other than some
props and printing the appropriate slides. ?5.00 Bundle 6 x 1 hour GCSE Design Resistant Materials
Revision Lessons Exam Questions Tools etc 6 x suggested 1 hour revision lessons on the theme of.
Powerpoint so can be used on the board or printed as a series of activities and worksheets. Control
rod geometry must not be able to over centre. T11.2. Steering must be by mechanical linkages only.
T11.3. Steering must be by front wheels only. T11.4. Steering must be operable by hand only.
Reviews Select overall rating (no rating) Your rating is required to reflect your happiness. To be
designed to take advantage of modern computer controlled manufacturing techniques such CNC
routing and waterjet cutting. Once it’s glued with PVA or other glue, it cannot break easily. But this
means that the driver must get out before changing the batteries which means slower pit stop. The
left picture shows what my basic idea was turned into and then the right picture shows the near
completed car. It is also important to keep the weight out of the end of the car, as it affects the
handling (how quickly the car can turn and how easy it is on it’s tyres) and how the car handles
bumps (weight in the ends can cause pitching, which can change the loading on the wheels) Then he
went on about the importance of aerodynamics compared to the importance of weight of the car.
Then I could bolt the whole component to the chassis. Scots Pine b. Cedar c. Parana Pine d.
Mahogany 7 Resistant Materials Revision Quiz What type of finish is shown in the image below? a.
This meant that one side fitted on perfectly, but the other side has somehow moved by 3mm. This
means that procedures reflect general practice and standards applicable at the time resources were
produced and cannot be assumed to be acceptable today.
The cross axle were designed to be welded on a tricycle. In my computer model, I need to see
whether a person would fit inside the car so I downloaded an ergonome off the internet and used
him to evaluated my model and see if it works. Hey all, the deadline for my resistant materials
coursework is really It s for gcse but it helps a bit you just need to write lods and lods more. There
are essentially 5 reading questions as Q1 has two parts. One after school session that I have attended,
I manage to screw and glued the battery box into the base. I need to consider this as it would
determine the position of the front wheels. I use these as one off lessons for lower school groups or
revision-style lessons with upper school groups. What is a HEALTHY, ACTIVE LIFESTYLE? “A
lifestyle that contributes positively to physical, mental and social wellbeing and includes regular
exercise and physical activity”. In the next slides I will be showing the progress of the car and how
each element of the car will be made and function. Nathaniel Olson GCSE Resistant Materials
Problems that I have encountered during the build of my car I have discovered that I have forgot to
make holes for 3 tabs on the car. Excretion of metabolic waste is a vital function and their
accumulation will result in eventual death. I chopped them off with an angle grinder with
supervision. See other similar resources ?5.00 (no rating) 0 reviews BUY NOW Save for later Not
quite what you were looking for. The disadvantages of this is that the car has to be lifted around to
get out of class rooms, or tight spaces in the paddock. The materials were a 1” inch steel tube and
some pieces from earlier on from the waterjet cutter. Putting a cassette on the motor shaft could be a
problem, as it is backwards from how normal bicycle parts work, and may require a lot of custom
work to get right. When I showed it to other students in the school, my car wasn’t completed as I
didn’t have the roll bar and the steering in it. The seat is in the right place except the angle is wrong.
You are being tested on your reading, not your writing skills. Things that I have found out about the
car: The motor layout won’t work Car is too thin Car is too long Nathaniel Olson GCSE Resistant
Materials Batteries and Motor Layout and The Shape of Chassis There are several advantages from
this layout. Nathaniel Olson GCSE Resistant Materials Interview with Chris Summary Basic car
built of 4x2 with attached structures for the steering and the drive system is a good idea. Evaporation
of water from a surface removes heat. 84. Keeping Cool Vasodilation, more blood flows nearer the
skin and heat is lost. Write a review Update existing review Submit review Cancel It's good to leave
some feedback. After some finishing touches with the paint, the wooden part of the chassis is
finished. See other similar resources ?2.00 5.00 1 review BUY NOW Save for later Not quite what
you were looking for. I have found out numerous things about my initial idea, how some of it will
work and some of it won’t. There is a material of specifications for this subject. All of the metal
parts will be standard carbon steel. The battery box is one of the good features of this car because,
it’s built on a set of rail, so when the driver gets out, it can slide out. Firstly the heat that the motor is
emitting can be direct into the batteries making them perform better.
It had to be simple to make and environmentally friendly. Powerpoint so can be used on the board or
printed as a series of activities and worksheets. Please essay writing company testimonials a valid
email address. Which wood would normally be used to make this product?. a. Scots Pine b. Cedar c.
Parana Pine d. Mahogany. On the left and below are some pictures showing the exploded view of
the car and how most of the components go together. It is also durable as it should last for half of a
decade of racing. It’s a good, neat place to put it, but the motor can get very hot while driving and
the lack of air flow would burn out the motor. Kidney dialysis 95. Kidney dialysis In the absence of
a suitable donor kidney, the alternative solution is for the patient to be hooked-up to a dialysis
machine every 2 - 3 days. The Heart 40. The Heart Pumps blood around the body. After some
finishing touches with the paint, the wooden part of the chassis is finished. Page Outline. Page
Analysis. CRITERION 1. Recognition of Problem. Arteries Veins and Capillaries 43. Blood 44.
Platelets Used in the clotting of blood. Nathaniel Olson GCSE Resistant Materials Task Analysis
Materials Wood Organic, non. Have you investigated environmental, ethical, social, and cultural
impacts of the product. Large amounts of dilute urine produced. 99. Cell Division - Mitosis 101.
DNA 102. Genetic and Environmental causes of Variation Variation is inherited. Write a review
Update existing review Submit review Cancel It's good to leave some feedback. Reviews Select
overall rating (no rating) Your rating is required to reflect your happiness. That would be linked with
two track rods, one for each wheel. Students have been climbing into the car, trying some features of
the car and getting a feel for it, all students felt that the car was big enough for themselves and had
no trouble with it. He suggested that mounting the cassette on the motor shaft would work with a
derailleur shifting the gears around. The battery box is under the seat to help the weight distribution
and the handling. It is a recessive allele which affects 1 in 2000 children. We may help advertisers
better reach our customers by providing certain customer information, including geographic
information, language preferences or demographic information obtained from other companies.
Nathaniel Olson GCSE Resistant Materials Third Idea This is a modification on the previous idea.
Then I welded the mounting plates onto each end of the tube so the roll bar can be firmly secured to
the chassis. From these Darwin produced his theory of evolution 112. Darwin 113. New Species ?
Survival of the Fittest The peppered moth. Name Candidate Number Walkden High School: 33383
OVERALL DEADLINE: Feb 14 th 2014. As this is a computer model, I made lots of changes to
the design as I went along. The roll bar is also made of aluminium as it’s required. The back
kingposts needed the tab but because the tab was flipped upside down, I heated the brass weld up
and twisted the kingpost around while the tab was in the vice.
Nathaniel Olson GCSE Resistant Materials Interview with Chris Summary Basic car built of 4x2
with attached structures for the steering and the drive system is a good idea. A message is sent to the
pituitary gland to release anti-diuretic hormone. I painted the top piece and the chassis separately
because it’s easier to paint the inside of the car without the top. But this means that the driver must
get out before changing the batteries which means slower pit stop. It limits the shape of the car to a
cylindrical or conical shape that can be bent from sheet material. All of the surfaces needed to be
painted with 2 coat to make sure no water will go into the wood. Commercial Catering: Hotels,
restaurants, clubs, wine bars and pubs. I learnt that I needed to make the chassis stronger and less
liable to sway side to side. To provide the metal components (steering and drivetrain) in a pre-
assembled form for schools that lack the ability to weld. Data Handling GCSE coursework.
Hypothesis. Data Handling GCSE coursework. Hypothesis. Data Handling GCSE coursework. Write
a review Update existing review Submit review Cancel It's good to leave some feedback. We also
used the wood as a board where we can fit electrical wires and devices. This brace should attach to
the chassis of the vehicle at one end, to not more than 200mm from the top of the roll bar at the
other, and must be capable of taking forward and rearward loadings. T9.3. Aluminium or steel roll
bars are to be used and must be strong enough and of sufficient dimensions to perform satisfactorily.
Media Studies 2, Gcse Social studies 5, All University Degree Subjects 35, You're using the Internet
Explorer 6 browser to view the BBC website. Natural finish b. Varnish c. Tanalising d. Spray
Painting 8 Resistant Materials Revision Quiz What type of finish is shown in the image below? a.
This idea would end up being too complicated and very tight spaces which would decrease the
efficiency of the motor. He suggested that mounting the cassette on the motor shaft would work with
a derailleur shifting the gears around. Knock down fittings (KD) Many DIY and furniture stores sell
their products flat packed in cardboard boxes. Blood Cells 46. Tissue exchange 47. The lymphatic
system Transports excess fluid from the tissues. Study Guides Understand coursework resistant topics
in IB with our teacher written Study Guides Learn more. Nitrogen Cycle 66. Food Production and
farming methods Monoculture. So the chassis would need to have that ability to be aerodynamic.
Abbie Sidaway. What different techniques could I use on my product. After all of the wood work
was done except the top piece, I got on with the painting of the car as it needed to be waterproof
otherwise it will warp and affect the car’s performance in wet weather. Write a review Update
existing review Submit review Cancel It's good to leave some feedback. This resource hasn't been
reviewed yet To ensure quality for our reviews, only customers who have purchased this resource can
review it Report this resource to let us know if it violates our terms and conditions. The tabs that
controls the steering wasn’t needed on the front kingposts as it would be moved. The steel would
have a coat of primer and 2 coats of black on top. Manufacturing Processes: Sand paper, square files,
electric drills, Router. However, it’s a good idea to write clearly and accurately.