Scribd Logo
Upload

Welcome to Scribd!

  • 9 views

    Is 10719 (Iso 1302) - 8

    Uploaded by

    Svapnesh Parikh
    This document provides guidance on indicating machining allowances and surface texture specifications on technical drawings. It states that machining allowances should be indicated to the left of the surface texture symbol in millimeters or inches. Surface texture specifications such as roughness values or grades should be placed relative to the symbol. The symbol and any inscriptions must be oriented to be read from the bottom or right side of the drawing and point to the surface, either with an arrow or by touching the surface line.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Is 10719 (Iso 1302) - 8

    Uploaded by

    Svapnesh Parikh
    9 views1 page
    This document provides guidance on indicating machining allowances and surface texture specifications on technical drawings. It states that machining allowances should be indicated to the left of the surface texture symbol in millimeters or inches. Surface texture specifications such as roughness values or grades should be placed relative to the symbol. The symbol and any inscriptions must be oriented to be read from the bottom or right side of the drawing and point to the surface, either with an arrow or by touching the surface line.

    Original Title

    IS 10719 (ISO 1302)_8

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides guidance on indicating machining allowances and surface texture specifications on technical drawings. It states that machining allowances should be indicated to the left of the surface texture symbol in millimeters or inches. Surface texture specifications such as roughness values or grades should be placed relative to the symbol. The symbol and any inscriptions must be oriented to be read from the bottom or right side of the drawing and point to the surface, either with an arrow or by touching the surface line.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    9 views1 page

    Is 10719 (Iso 1302) - 8

    Uploaded by

    Svapnesh Parikh
    This document provides guidance on indicating machining allowances and surface texture specifications on technical drawings. It states that machining allowances should be indicated to the left of the surface texture symbol in millimeters or inches. Surface texture specifications such as roughness values or grades should be placed relative to the symbol. The symbol and any inscriptions must be oriented to be read from the bottom or right side of the drawing and point to the surface, either with an arrow or by touching the surface line.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    IS: 10719-l 983

    IS0 1302-l 978

    4.4 Indication of machining allowance

    Where it is necessary to specify the value of the machining allowance, this.shall be indicated on the left of the symbol as
    shown in figure 13. This value shall be expressed in millimetres or inches, according to the general system used for
    dimensioning the drawing.

    FIGURE 13

    4.5 Position of the specifications of surface texture in the symbol

    The specifications of surface texture shall be placed relative to the symbol as shown in figure 14.

    a = Roughness value R, in micrometres

    or

    Roughness grade number Nl to N12


    b
    a / c(f) Production method, treatment or coating

    C = Sampling length

    d= Direction of lay

    e = Machining allowance

    FIGURE 14 f = Other roughness values (in brackets)

    5 INDICATIONS ON DRAWINGS

    5.1 In conformity with ISO/R 129, the symbol, as well as the inscriptions, shall be orientated so they may be read from the
    bottom or the right-hand side of the drawing (see figure 1.5).

    If it is not practicable to adopt this general rule, the symbol may be drawn in any position, but only provided that it does not
    carry any indications of special surface texture characteristics or of.machining allowances (as given in 4.2 to 4.4).
    Nevertheless, in such cases the inscription defining the value of the principal criterion of roughness (if present) must always
    be written in conformity with the general rule (see figure 16).

    If necessary, the symbol may be connected to the surface by a leader line terminating in an arrow.

    The.symbol or the arrow shall point from outside the material of the piece, either to the line representing the surface, or to
    an extension of it~(see figure 15).

    FIGURE 15
    1 a

    FIGURE 16
    a

    You might also like