This document provides instructions for safely setting up and starting a battery charger:
1) Place the charger in a well-ventilated area at least 6 inches from any surface.
2) Disconnect and lock out all AC and DC power sources before making any electrical connections.
3) Connect the AC power input and DC battery or bus output, checking that voltages and currents match the nameplate ratings.
Recheck all wiring before turning on any power breakers or switches to start the charger.
This document provides instructions for safely setting up and starting a battery charger:
1) Place the charger in a well-ventilated area at least 6 inches from any surface.
2) Disconnect and lock out all AC and DC power sources before making any electrical connections.
3) Connect the AC power input and DC battery or bus output, checking that voltages and currents match the nameplate ratings.
Recheck all wiring before turning on any power breakers or switches to start the charger.
This document provides instructions for safely setting up and starting a battery charger:
1) Place the charger in a well-ventilated area at least 6 inches from any surface.
2) Disconnect and lock out all AC and DC power sources before making any electrical connections.
3) Connect the AC power input and DC battery or bus output, checking that voltages and currents match the nameplate ratings.
Recheck all wiring before turning on any power breakers or switches to start the charger.
This document provides instructions for safely setting up and starting a battery charger:
1) Place the charger in a well-ventilated area at least 6 inches from any surface.
2) Disconnect and lock out all AC and DC power sources before making any electrical connections.
3) Connect the AC power input and DC battery or bus output, checking that voltages and currents match the nameplate ratings.
Recheck all wiring before turning on any power breakers or switches to start the charger.
p place the charger - u in a well ventilated S ET area C K T U I E E Q SH COOL AIR 6in/153mm
2) safety first disconnect and lock-out all ac sources and dc battery voltages
dc source ac source off and off and or battery disconnect locked LOCKED disconnect switch switch
3) electrical connections a) connect ac power to the charger ac source ac volts Ac input VOLTAGE and phase voltage
EVO WARNING BATTERY CHARGER / RECTIFIER
This Unit Has Been Connected
For An Output Of INPUT OUTPUT Volts
Phase V
Do Not Connect To Other Voltage Without Reconnecting Input Transformer - See Instruction Manual
battery charger JC0011-00
tag on warning tag data nameplate ac breaker all these parameters must match !
b) connect the battery or dc bus
FACTORY PRESET BATTERY OR
VOLTAGES DC BUS NOTICE At The Factory As Follows DC Output Charging Voltages Have Been Preset At The Factory As Follows Float Mode: Volts Float Mode: Volts
Equalize Mode: Volts
Equalize Mode: Volts These Voltages Are Adjustable Please Consult Operating Manual These Voltages Are Output Current Limit Has Been Set At DC Amps
JC0016-00 please check the operating instructions provided with your battery tag on dc breaker for proper charging voltages
4) starting the charger
recheck your wiring! if it is correct, follow the start sequence below Turn TURN ON ON
1 3 ac source distribution panel Turn ac breaker on 2 4 Turn dc breaker on
5) setting THE parameters
adjustable parameters (in selection order):
1) float voltage 4) high dc voltage alarm
Float Eqlz Mthd: Man 2) equalize voltage 5) low dc voltage alarm 3) equalize timer hours 6) current limit 131.0 Amps Volts
press the enter key once to begin the adjustment process.
5.0 the first value (float voltage) will be displayed. adjust this value by pressing the up or down arrow keys. press “enter” again to save and advance to the next parameter For adjustment. repeat this process to adjust the rest of The parameters listed above.
if no keys are pressed for 25 seconds, the charger will
return to normal operation.
For further instructions be sure to read the operating and
service instructions or visit online at ... atseries.net d o n e ! JC5020-51 please check the operating instructions provided with your battery for proper charging voltages
5-1) SETTING THE - PRESS EDIT/ENTER KEY
FLOAT VOLTAGE LCD Screen WILL Display THE FLOAT VOLTAGE see Manual Float Voltage (V)
131.0 section 3.3 Menu Back Enter Accept - PRESS THE ARROW KEYS UP ARROW KEY WILL INCREASE Float Voltage (V) DOWN ARROW WILL DECREASE - PRESS EDIT/ENTER KEY 131.0 WILL SAVE YOUR CHANGES AND GO TO THE NEXT PARAMETER Menu Back Enter Accept
5-2) SETTING THE - PRESS EDIT/ENTER KEY
EQUALIZE VOLTAGE LCD Screen WILL Display THE EQUALIZE VOLTAGE see Manual Equalize Voltage (V)
139.0 section 3.3 Menu Back Enter Accept - PRESS THE ARROW KEYS UP ARROW KEY WILL INCREASE Equalize Voltage (V) DOWN ARROW WILL DECREASE
139.0 - PRESS EDIT/ENTER KEY WILL SAVE YOUR CHANGES AND GO TO THE NEXT PARAMETER Menu Back Enter Accept
5-3) SETTING THE
- PRESS EDIT/ENTER KEY EQUALIZE TIMER Equalize Time(hours) LCD Screen WILL Display THE EQUALIZE TIMER 24 see Manual Menu Back Enter Accept - PRESS THE ARROW KEYS section 3.3 UP ARROW KEY WILL INCREASE Equalize Time(hours) DOWN ARROW WILL DECREASE
24 - PRESS EDIT/ENTER KEY
WILL SAVE YOUR CHANGES AND GO TO THE NEXT PARAMETER Menu Back Enter Accept
5-4) SETTING THE
HIGH DC VOLTAGE - PRESS EDIT/ENTER KEY ALARM High DC Alarm (V) LCD Screen WILL Display THE HIGH DC ALARM (V) 144.0 see Manual Menu Back Enter Accept - PRESS THE ARROW KEYS section 3.3 UP ARROW KEY WILL INCREASE High DC Alarm (V) DOWN ARROW WILL DECREASE
144.0 - PRESS EDIT/ENTER KEY
WILL SAVE YOUR CHANGES AND GO TO THE NEXT PARAMETER Menu Back Enter Accept
5-5) SETTING the
- PRESS EDIT/ENTER KEY LOW DC VOLTAGE ALARM Low DC Alarm (V) LCD Screen WILL Display THE Low dc alarm (V) see Manual 120.0 Menu Back Enter Accept - PRESS THE ARROW KEYS section 3.3 UP ARROW KEY WILL INCREASE Low DC Alarm (V) DOWN ARROW WILL DECREASE
120.0 - PRESS EDIT/ENTER KEY
WILL SAVE YOUR CHANGES AND GO TO THE NEXT PARAMETER Menu Back Enter Accept
5-6) SETTING the
- PRESS EDIT/ENTER KEY CURRENT LIMIT see Manual Current Limit (A) LCD Screen WILL Display THE Current limit 120.0 section 3.3 Menu Back Enter Accept - PRESS THE ARROW KEYS UP ARROW KEY WILL INCREASE Current Limit (A) DOWN ARROW WILL DECREASE
120.0 - PRESS EDIT/ENTER KEY
WILL SAVE YOUR CHANGES AND GO TO THE NEXT PARAMETER Menu Back Enter Accept
