User Quick Reference Guide

RINS2061-1

Arming the Panel

By Code By Proximity Tag By Remote Key Fob

Enter a valid code. Present a valid proximity tag. Select the area/s you wish to set by
pressing either the , I or II button
Select the area/s you wish to set, Select the area/s you wish to set, on the key fob.
‘Please wait arming wireless’ may be ‘Please wait arming wireless’ may be
displayed. displayed. ‘Please wait arming wireless’ will be
displayed.
Leave via the designated exit route Leave via the designated exit route
agreed with your engineer. agreed with your engineer. Leave via the designated exit route
agreed with your engineer.
Leave the area in the allotted time Leave the area in the allotted time
and make sure the exit door is and make sure the exit door is Leave the area in the allotted time
closed correctly behind you. closed correctly behind you. and make sure the exit door is
closed correctly behind you.

Dis-Arming the Panel

By Code By Proximity Tag By Remote Key Fob

Enter the premises, the entry time Enter the premises, the entry time Enter the premises, the entry time
should begin. should begin. should begin.

Go to a keypad and enter a valid Present a valid proximity tag to a Press the  button on the key fob.
code. proximity reader.
The panel is now disarmed.
The panel is now disarmed. The panel is now disarmed.
PLEASE NOTE: The panel may be set up so
that an entry time is not required to disarm the
system.

Viewing and Clearing a Fault

Any faults that occur on the system will cause the Alert LED (furthest left) to flash on the panel.

Enter a valid code or present a valid proximity tag and the panel should display the fault.

If the fault no longer exists you can clear the fault from the LCD screen by pressing h.

If at this point the panel displays ‘Restore Required’, you should call your engineer as soon as possible.

Anti-Code Restore
After the fault has been cleared the panel may display ‘Anti-Code Restore Required’.

If this occurs, note down the number displayed (including the G) and call the ARC.

Quote the number and record the six digit number received.

Press h so that the home screen is displayed and enter the six digit number.

The Alert LED should extinguish and the panel should return to normal.

Installer Name....................................... Company....................................... Tel number.......................................

 Entering & Exiting Manager Menu
Press d then enter the Manager code (default 2222).

Press h to scroll through the menu and f to select options.

To exit the menu scroll to ‘EXIT MANAGER MENU’ and press f.

Adding a New User

Enter Manager menu and press h until the screen displays ‘EDIT USERS?’ then press f.

‘Add New User’ will be displayed then press f and the screen will switch to the next available user.

Press f and the LCD will display ‘Enter User Code [ ]’.

Enter the new code or present a new proximity fob and press f. If it is a remote key fob to be learnt to the panel,
at this point press and hold thefor 3 seconds then release.

A user name can now be entered to identify the code/tag/fob then press f.

At this point the privileges of the user can be set up, for more information please refer to the User Manual.

Changing/Deleting a User
Enter Manager menu and press h until the screen displays ‘EDIT USERS?’ then press f.

“Add New User” will be displayed, press h and ‘Delete/Change User’ will be displayed. Press f.

Scroll using d to the user you wish to change/delete and press f.

If this user is to be deleted, at this point press f if not press h so the LCD now displays ‘Change User’.

Press f to edit the user privileges.

Changing your Limited User Code

Press d then enter your user code.

The screen will display ‘CHANGE CODE?,’ press f then c to delete the old user code.

The LCD will display ‘CHANGE CODE?’ again. Press f, enter your new user code and press f.

Reviewing the Logs

Enter Manager menu and press h to scroll to ‘REVIEW LOGS’ then press f.

Press f and the most recent event will be displayed. Press b or d to scroll backwards and forwards through
the log.

If there is any more information on a log event, press c and the panel will show the information.

PLEASE NOTE: This is a generic user reference manual for the EURO, PCX and Enforcer range
of control panels. The menu option displayed on each panel type may differ slightly but still follow
the same programming path as the instructions above. If you require further clarity please refer to
the user manual provided with the control panel or contact a registered alarm engineer.

Installer Name....................................... Company....................................... Tel number.......................................