Manual GSM SIM5320
Manual GSM SIM5320
Manual GSM SIM5320
GSM-Q2403
Features
• Dual Band 900 / 1800 MHz for UK Use
Description
The GSM-Q2403 Modem is ideal for a wide range of applications. The modem can be used to make circuit
switched data calls (CSD), making the unit suitable for remote dial-up systems where a fixed phone line
is not available. The SMS functionality enables the sending and receipt of text messages. A common use
for this functionality is an SMS server for the automated sending and receipt of bulk text messages.
The modem implements the Wavecom 2403 GSM Engine. This ensures high quality and reliable operation
along with compatibility with all standard GSM networks.
The modem is supplied in a rugged extruded aluminium enclosure making it suitable for use in a wide
range of industrial and demanding environments. The unit connects directly to a PC or terminal device via
the DB-9 RS232 Cable interface. The integral SIM card holder accepts standard SIM cards . The only
other connections required are to dc power supply and Antenna .
Key Features
Features Implementation
Transmission Data, SMS, Fax
Standby ~55mA
Current Consumption
Working Current 100-140mA
GSM class Small MS. (GSM07.07 and 07.05)
GPRS Class 8
Interface description
The GSM Terminal provides the following connectors for power supply, interfacing and antenna:
• 2.1mm DC power connector (centre/inner pin is positive)
• 9-pin (female) D-SUB plug for RS-232 serial interface
• SMA connector for antenna (radio interface)
• SIM card holder
Power Supply
The power supply of the GSM Terminal should be a single voltage source of Vin=6-36V providing a peak
current of up to 500mA during transmission.
The terminal can be turned on by connecting power. The terminal power supply circuit automatically gen-
erates a low pulse signal not less than 100ms in order to wake up the GSM engine.
Each time the terminal is shut down, data will be written from the volatile memory to flash memory. The
guaranteed maximum number of write cycles is limited to 100,000.
RS232 Interface
Via RS-232 interface, the host controller controls the TMAS GSM/GPRS Terminal and transports data.
The table below shows the pin assignment of RS-232 (D-SUB 9-pin female).
The GSM/GPRS Terminal is designed for use as DCE. Based on the conventions for DCE-DTE connection,
it communicates with the user application (DTE) using the following signals:
Pin TxD @ application sends data to TxD of GSM/GPRS Terminal
Pin RxD @ application receives data from RxD of GSM/GPRS Terminal
Start the HyperTerminal program and assign any name for a new session.
Choose the Com port connected to the modem. The unit features auto bauding so any baud
rate from 1.2 to 115.2 Kbps can be used, 8bits, no parity bit, 1 stop bit)
On the terminal screen, type “AT” to check the “OK” response from the modem
Status LED
Reader Response
It is our intention to provide you with the best documentation possible to ensure successful use of your
QuasarUK product.
If you wish to provide your comments on organization, clarity, subject matter, and ways in which our
documentation can better serve you, please email us your comments to the Technical Publications Man-
ager
The following is a few suggestions to comments you may have….
Application:
Would you like a reply? Y/N
Datasheet: DS-GSM-Q2403-1
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
QuasarUK is an internet based company. All Sales / support and interface is via our website at
www.quasaruk.co.uk
Disclaimer:
Whilst the information in this document is believed to be correct at the time of issue, QuasarUK Ltd does not accept any liability
liability
whatsoever for its accuracy, adequacy or completeness. No express or implied warranty or representation is given relating to the
information contained in this document. QuasarUK Ltd reserves the right to make changes and improvements to the product(s)
described herein without notice. Buyers and other users should determine for themselves the suitability of any such information
or products for their own particular requirements or specification(s). QuasarUK Ltd shall not be liable for any loss or damage
caused as a result of user’s own determination of how to deploy or use R F Solutions Ltd’s products. Use of QuasarUK Ltd prod-
ucts or components in life support and/or safety applications is not authorised except with express written approval. No licences
licences
are created, implicitly or otherwise, under any of QuasarUK Ltd’s intellectual property rights. Liability for loss or damage result-
result-
ing or caused by reliance on the information contained herein or from the use of the product (including liability resulting from neg-
ligence or where QuasarUK Ltd was aware of the possibility of such loss or damage arising) is excluded. This will not operate to
limit or restrict QuasarUK Ltd’s liability for death or personal injury resulting from its negligence.