Scribd
Upload
15 views5 pages

EDC Lab 01 Fall 2023

This document is a laboratory manual for an Electronic Devices and Circuits course containing instructions for two laboratory experiments using Proteus simulation software. The first experiment involves constructing a circuit with four diodes and an AC voltage source to analyze the output waveform. The second experiment constructs a circuit with a diode, DC voltage source, voltmeter, ammeter and resistor to measure voltage and current values across the diode at varying input voltages and record the results.

Uploaded by

i222200 Muhammad Ahmed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
15 views5 pages

EDC Lab 01 Fall 2023

This document is a laboratory manual for an Electronic Devices and Circuits course containing instructions for two laboratory experiments using Proteus simulation software. The first experiment involves constructing a circuit with four diodes and an AC voltage source to analyze the output waveform. The second experiment constructs a circuit with a diode, DC voltage source, voltmeter, ammeter and resistor to measure voltage and current values across the diode at varying input voltages and record the results.

Uploaded by

i222200 Muhammad Ahmed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Electronic Devices and Circuits

(EL-1004)
LABORATORY MANUAL
FALL 2023

LAB 01 (LAB # 01)


Familiarization to Proteus and Lab Equpiment
:
Familiarization to Proteus and Lab Equipment
Engr. Kashif Ullah Khattak

Student Name: __Muhammad _Ahmed_Khan

Roll No: __22I-2200____ Section: ______A____

Date performed: __________________________

Manual Submission Date: __________________

_______________________________
LAB ENGINEER SIGNATURE & DATE

MARKS AWARDED: /10

______________________________________________________________________________________________________________________________________________________

NATIONAL UNIVERSITY OF COMPUTER AND EMERGING SCIENCES, ISLAMABAD


Prepared by: Engr. Naveed Iqbal Version: 2.14
Last Edited by: Engr. Maria Nasir Updated: Fall 2023
Verified by: Dr. Rashad Ramzan
Electronic Devices National University Roll No: __________
01

Lab #
& Circuits of Computer and Emerging Sciences
(EL-1004) Islamabad
_________________________________________________________________________________

TASK # 1:

INTRODUCTION:
Performing task 1 of lab manual 1, in which we have to design the following circuit on
proteus:

PROCEDURE:
1. To begin, I developed a circuit simulation.
2. This circuit incorporates four diodes, an AC voltage source, and an oscilloscope for
waveform analysis.
3. Once the circuit was constructed, I adjusted the AC source's amplitude to 12V and its
frequency to 50Hz.

EDC LAB NUCES, ISLAMABAD Page 2 of 5


Electronic Devices National University Roll No: __________
01

Lab #
& Circuits of Computer and Emerging Sciences
(EL-1004) Islamabad
_________________________________________________________________________________

4. Employing this setup resulted in the generation of the following waveform.


CIRCUIT DIAGRAM:

TASK # 2:

INTRODUCTION:

EDC LAB NUCES, ISLAMABAD Page 3 of 5


Electronic Devices National University Roll No: __________
01

Lab #
& Circuits of Computer and Emerging Sciences
(EL-1004) Islamabad
_________________________________________________________________________________

We are constructing a circuit as shown below, on proteus and simulate.We will vary the input
voltage Vin according the values given in the table and by using ampere meter and volt meter
record the values of Id and Vd.

PROCEDURE:
The primary objective within this circuit was the determination of voltage and current values.
2. Initially, I formulated a circuit simulation.
3. The circuit configuration encompassed a DC voltage source, a diode, a DC voltmeter, a
DC ammeter, and a 1k-ohm resistor.
4. To achieve this, the voltmeter was connected in parallel to exploit uniform voltage across
parallel elements, while the ammeter was situated in series to capitalize on consistent current
flow within the series arrangement.
CIRCUIT DIAGRAM:

EDC LAB NUCES, ISLAMABAD Page 4 of 5


Electronic Devices National University Roll No: __________
01

Lab #
& Circuits of Computer and Emerging Sciences
(EL-1004) Islamabad
_________________________________________________________________________________

Vin Simulated Results


(V) Vd (V) Id (mA) Slope (Id/Vd)
0.0 0 0 0
0.2 0.2 0 0
0.4 0.4 0 0
0.6 0.57 0.03 0.052
0.8 0.611 0.19 0.31
1.0 0.63 0.37 0.587
1.2 0.64 0.56 0.875
1.4 0.65 0.75 1.15
1.6 0.63 0.95 1.50

1.8 0.66 1.14 1.72


2.0 0.66 1.34 2.03
3.0 0.68 2.32 3.41
4.0 0.69 3.31 4.79

5.0 0.69 4.31 6.24


6.0 0.70 5.30 7.5
7.0 0.70 6.30 9
8.0 0.71 7.29 10.26
9.0 0.71 8.29 11.6
10.0 0.72 9 12.5

EDC LAB NUCES, ISLAMABAD Page 5 of 5

You might also like