4DLCD 35480320
4DLCD 35480320
4DLCD 35480320
4DLCD-35480320-[RTP/CTP]-[CLB]
3.5” TFT Liquid Crystal Display
DATASHEET
Document Date: 18th January 2019
Document Revision: 1.0
Revision History
REVISION DATE COMMENT REMARKS
1.0 18/01/2019 Initial Version Initial Version
4DLCD-35480320-[RTP/CTP]-[CLB]
Table of Contents
1. General Specification ................................................................................................................................................3
2. TFT LCD Display Drawing (Non Touch Version) .........................................................................................................4
3. TFT LCD Display Drawing (Resistive Touch Version) ..................................................................................................5
4. TFT LCD Display Drawing (Capacitive Touch Version) ...............................................................................................6
5. TFT LCD Display Drawing (Capacitive Touch Version with Cover Lens Bezel) ............................................................7
6. Absolute Maximum Ratings ......................................................................................................................................8
7. Electrical Characteristics ...........................................................................................................................................8
8. Electro-Optical Characteristics ..................................................................................................................................8
9. Backlight Characteristics ...........................................................................................................................................9
10. Interface Descriptions .............................................................................................................................................11
10.1. LCD Interface ................................................................................................................................................ 11
10.2 CTP Interface .................................................................................................................................................... 12
11. Initialisation Code ...................................................................................................................................................13
12. LCD Timing Details ..................................................................................................................................................15
12.1. Timing Chart ................................................................................................................................................. 15
12.2. Reset Timing ................................................................................................................................................. 16
12.3. Power On Sequence ..................................................................................................................................... 16
12.3.1. Case 1 - RES line is held High or Unstable by Host at Power ON ......................................................... 16
TFT LCD
1. General Specification
4DLCD-35480320 is a colour active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It
is composed of a colour TFT-LCD panel, driver IC, FPC and a back light unit and with/without a Resistive/Capacitive
Touch Panel (RTP or CTP), and with/without Cover Lens Bezel (CLB). The module display area contains 320 x 480
pixels. This product accords with RoHS environmental criterion.
5. TFT LCD Display Drawing (Capacitive Touch Version with Cover Lens Bezel)
4DLCD-35480320-[RTP/CTP]-[CLB]
TFT LCD
7. Electrical Characteristics
PARAMETER SYMBOL MIN TYP MAX UNIT
Power Voltage VDD/DCC 2.6 2.8 3.3 V
Input Current IVDD - - - mA
Input Voltage ‘H’ Level VIH 0.7 VDD - VDD V
Input Voltage ‘L’ Level VIL 0 - 0.3 VDD V
8. Electro-Optical Characteristics
ITEM SYM CONDITION MIN TYP MAX UNIT REMARK
Response Time Tr+Tf θ=0 - 30 - ms Figure 1 (4)
Contrast Ratio Cr ° - 250 - - Figure 2 (1)
δ
Luminance Uniformity ∅=0 75 80 - % Figure 2 (3)
WHITE
4DLCD-35480320 205 228 -
4DLCD-35480320-RTP 164 182 -
Surface Luminance Lv 4DLCD-35480320-CTP 195 216 - cd/m2 Figure 2 (2)
4DLCD-35480320-CTP-
195 216 -
CLB
∅ = 90° - 35 -
TFT LCD
∅ = 270° - 55 -
Viewing Angle Range θ deg Figure 3 (6)
∅ = 0° - 55 -
∅ = 180° - 55 -
x 0.574 0.624 0.674
Red
y 0.318 0.368 0.418
x θ=0° 0.300 0.350 0.400
Green
CIE (x,y) y ∅=0° 0.500 0.550 0.600
Figure 2 (5)
Cromacity x Ta=25 0.093 0.143 0.193
Blue
y 0.069 0.119 0.169
x 0.260 0.310 0.360
White
y 0.283 0.333 0.383
9. Backlight Characteristics
PARAMETER SYMBOL MIN TYP MAX UNIT
Voltage for LED backlight Vl - 3.2 3.4 V
Current for LED backlight Il - 120 150 mA
LED Life Time - 30000 - - Hrs
Note: The LED life time is defined as the module brightness decrease to 50% original brightness at Ta=25°C.
4DLCD-35480320-[RTP/CTP]-[CLB]
Note 1: Contrast Ratio(CR) is defined mathematically as below, for more information see Figure 1.
Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
Contrast Ratio =
Average Surface Luminance with all black pixels (P1, P2, P3, P4, P5)
Note 2: Surface luminance is the LCD surface from the surface with all pixels displaying white.
For more information, see Figure 2.
Lv = Average Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
Note 3: The uniformity in surface luminance δ WHITE is determined by measuring luminance at each test position 1
through 5, and then dividing the maximum luminance of 5 points luminance by minimum luminance of 5 points
luminance. For more information, see Figure 2.
Minimum Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
δ WHITE =
Maximum Surface Luminance with all white pixels (P1, P2, P3, P4, P5)
Note 4: Response time is the time required for the display to transition from white to black (Rise Time, Tr) and from
black to white (Decay Time, Tf). For additional information see FIG 1. The test equipment is Autronic-Melchers
ConoScope series.
Note 5: CIE (x, y) chromaticity, the x, y value is determined by measuring luminance at each test position 1 through 5,
and then make average value.
Note 6: Viewing angle is the angle at which the contrast ratio is greater than 2. For TFT module the contrast ratio is
greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis
which is normal to the LCD surface. For more information, see Figure3.
Note 7: For viewing angle and response time testing, the testing data is based on Autronic-Melchers ConoScope series.
Instruments for Contrast Ratio, Surface Luminance, Luminance Uniformity, CIE the test data is based on TOPCONs BM-5
TFT LCD
photo detector.
Figure 2. Measuring method for Contrast ratio, surface luminance, Luminance uniformity, CIE (x, y) chromaticity
5 YD/CTP_INT Note 3
CTP/No Connection (NC) for Non touch Version
The touch panel X left pin for RTP/ I2C SCL for CTP / No
6 XL/CTP_SCL Note 3
Connection (NC) for Non touch Version
7 RESET Reset input signal
Instruction Register/Data Register selection pin for MCU
8 RS/(SCL)
mode / SPI Serial Clock for SPI mode
9 CS Chip select input pin
10 RD/(VCC) Read signal for MCU mode / Tie to VCC for SPI mode
Write signal for MCU mode / Data or Command selection for
11 WR/(D/C)
SPI mode
12 VCC Power supply
13 NC/(SDO) No Connect for MCU mode / Serial Data Output for SPI mode
14 GND Ground
15 DB15/(GND) Databus DB15 for MCU mode / Tie to GND for SPI mode Note 2
16 DB14/(GND) Databus DB14 for MCU mode / Tie to GND for SPI mode Note 2
17 DB13/(GND) Databus DB13 for MCU mode / Tie to GND for SPI mode Note 2
18 DB12/(GND) Databus DB12 for MCU mode / Tie to GND for SPI mode Note 2
19 DB11/(GND) Databus DB11 for MCU mode / Tie to GND for SPI mode Note 2
20 DB10/(GND) Databus DB10 for MCU mode / Tie to GND for SPI mode Note 2
21 DB9/(GND) Databus DB9 for MCU mode / Tie to GND for SPI mode Note 2
22 DB8/(GND) Databus DB8 for MCU mode / Tie to GND for SPI mode Note 2
23 DB7/(GND) Databus DB7 for MCU mode / Tie to GND for SPI mode Note 2
24 DB6/(GND) Databus DB6 for MCU mode / Tie to GND for SPI mode Note 2
25 DB0/(GND) Databus DB0 for MCU mode / Tie to GND for SPI mode Note 2
26 DB1/(GND) Databus DB1 for MCU mode / Tie to GND for SPI mode Note 2
27 DB2/(GND) Databus DB2 for MCU mode / Tie to GND for SPI mode Note 2
28 DB3/(GND) Databus DB3 for MCU mode / Tie to GND for SPI mode Note 2
TFT LCD
29 DB4/(GND) Databus DB4 for MCU mode / Tie to GND for SPI mode Note 2
30 DB5/(GND) Databus DB5 for MCU mode / Tie to GND for SPI mode Note 2
The touch panel Y up pin for RTP / Reset pin for CTP / No
31 YU/CTP_RST Note 3
Connection (NC) for Non touch Version
The touch panel X right pin for RTP / I2C SDA Pin for CTP / No
32 XR/CTP_SDA Note 3
Connection (NC) for Non touch Version
33 LEDA Anode of LED Backlight
34 LEDK1 Cathode1 of LED Backlight
35 LEDK2 Cathode2 of LED Backlight
36 LEDK3 Cathode3 of LED Backlight
37 LEDK4 Cathode4 of LED Backlight
38 LEDK5 Cathode5 of LED Backlight
39 LEDK6 Cathode6 of LED Backlight
40 GND Ground
write_reg(0xCF);
write_dat(0x00);
write_dat(0x83);
write_dat(0x30);
write_reg(0xED);
write_dat(0x64);
write_dat(0x03);
write_dat(0X12)
write_dat(0X81)
write_reg(0xCB);
write_dat(0x39);
write_dat(0x2C);
write_dat(0x00);
write_dat(0x34);
write_dat(0x02);
write_reg(0xEA);
write_dat(0x00);
write_dat(0x00);
write_reg(0xE8);
write_dat(0x85);
write_dat(0x10);
write_dat(0x79);
write_dat(0x11); //SAP[2:0];BT[3:0]
write_reg(0xC2);
write_dat(0x11);
write_reg(0x3A);
write_dat(0x55);
write_reg(0x36); // Memory Access Control
write_dat(0x08);
write_reg(0xB1);
write_reg(0XF7);
write_dat(0x20);
4DLCD-35480320-[RTP/CTP]-[CLB]
write_reg(0XF1);
write_dat(0x01);
write_dat(0x30);
write_reg(0x26);
write_dat(0x01);
write_dat(0x2C);
write_dat(0XA2);
write_dat(0x3F);
write_dat(0x05);
write_dat(0x0E);
write_dat(0x0C);
write_dat(0x37);
write_dat(0x3C);
write_dat(0x0F);
Power off
70℃±2℃ 96H
3 High Temperature Operation
Power on
-20℃±2℃ 96H
4 Low Temperature Operation
Power on After test cosmetic and
electrical defects should not
60℃±2℃ happen.
5 High Temperature & Humidity Operation 90%RH 96H
Power on
-20℃←→25℃←→70℃
30min 5min 30min
6 Temperature Cycle
After 10 cycles, restore 2H at
25℃
Power off
7 Vibration Test 10Hz~150Hz, 100m/s2, 120min
8 Shock Test Half-sinewave, 300m/s2, 11ms
TFT LCD
Do not apply excessive force to the display surface or to the adjoining areas since this may cause the color tone
to vary. Do not touch the display with bare hands. This will stain the display area and degraded insulation
between terminals (some cosmetics are determined by the polarizer).
The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer
carefully. Do not touch, push or rub the exposed polarizer with anything harder than an HB pencil lead
(e.g., glass, tweezers, etc.). Do not put or attach anything on the display area to avoid leaving marks on it.
Condensation on the surface and contact with terminals due to cold temperature will damage, stain or
contaminate the polarizer. After products are tested at low temperature they must be warmed up in a container
before coming into contact with room temperature air.
If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If
it is heavily contaminated, moisten the cloth with one of the following solvents
o Isopropyl alcohol
o Ethyl alcohol
Solvents other than those mentioned above may damage the polarizer. Especially the following.
o Water
o Ketone
o Aromatic solvents
Wipe off saliva or water drops immediately, contact with water over a long period of time may cause
TFT LCD
o Before removing the LCM from its packing case or incorporating it into a set, be sure that the module
and your body has the same electric potential. Be sure to ground your body when handling the LCD
modules.
o To reduce the amount of static electricity generated, do not conduct assembly and other work under
dry conditions. To reduce the generation of static electricity, please ensure that the air in the work
environment is not too dry. A relative humidity of 50%-60% is recommended. As much as possible,
make the electric potential of your work clothes and that of the work bench the ground potential.
o The LCD module is coated with a film to protect the display surface. Be careful when peeling off this
4DLCD-35480320-[RTP/CTP]-[CLB]
Store them in a sealed polyethylene bag. If properly sealed, there is no need for the desiccant.
Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature between 0℃
and 35℃, and keep the relative humidity between 40%RH and 60%RH.
The polarizer surface should not come in contact with any other objects. (We advise you to store them in an
anti-static electricity container in which they were shipped. Some Liquid crystals solidify under low temperature
(below the storage temperature range) leading to defective orientation or the generation of air bubbles (black
or white). Air bubbles may also be generated if the module is subjected to low temperature.
TFT LCD
If the LCD modules have been operating for a long time showing the same display patterns, the display patterns
may remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating
status can be regained by suspending use for some time. It should be noted that this phenomenon does not
adversely affect performance reliability.
To minimize the performance degradation of the LCD modules resulting from destruction caused by static
electricity etc., please avoid holding the following sections when handling the modules’
o Exposed area of the printed circuit board
o Terminal electrode sections
The information contained in this document is the property of 4D LCD Pty. Ltd.; these may be the subject of patents
pending or granted, and must not be copied or disclosed without prior written permission.
4D LCD endeavors to ensure that the information in this document is correct and fairly stated but does not accept
liability for any error or omission. The development of 4D LCD products and services is continuous and published
information may not be up to date. It is important to check the current position with 4D LCD.
4D LCD reserves the right to modify, update or makes changes to Specifications or written material without prior notice
at any time.
4DLCD-35480320-[RTP/CTP]-[CLB]
All trademarks belong to their respective owners and are recognized and acknowledged.
4D LCD Pty Ltd makes no warranty, either expressed or implied with respect to any product, and specifically disclaims
all other warranties, including but without limitation to; warranties for merchantability, non-infringement and fitness
for any particular purpose.
Information contained in this publication regarding device applications and the like is provided only for your
convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with
your specifications.
Images and graphics used throughout this document are for illustrative purposes only. All images and graphics used are
possible to be displayed on the 4D LCD range of products, however the quality may vary.
In no event shall 4D LCD be liable to the buyer or to any third party for any indirect, incidental, special, consequential,
punitive or exemplary damages (including but without limitation to; lost profits, lost savings, or loss of business
opportunity) arising out of or relating to any product or service provided or to be provided by 4D LCD, or the use or
inability to use the same, even if 4D LCD has been advised of the possibility of such damages.
4D LCD products are not fault tolerant nor designed, manufactured or intended for use or resale as on line control
equipment in hazardous environments requiring fail – safe performance, such as in the operation of nuclear facilities,
aircraft navigation or communication systems, air traffic control, direct life support machines or weapons systems in
which the failure of the product could lead directly to death, personal injury or severe physical or environmental
damage (‘High Risk Activities’). 4D LCD and its suppliers specifically disclaim any expressed or implied warranty of
fitness for High Risk Activities.
Use of 4D LCD products and devices in 'High Risk Activities' and in any other application is entirely at the buyer’s risk,
and the buyer agrees to defend, indemnify and hold harmless 4D LCD from any and all damages, claims, suits, or
expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any 4D LCD intellectual
property rights.
TFT LCD