Scribd
Upload
109 views5 pages

Analog Style VU Meter On OLED Display - Arduino Compatible

This document describes an analog-style VU meter project using a 0.96" OLED display and Arduino-compatible microcontroller. The project includes an audio input, potentiometer to adjust signal level, and OLED display driven by Arduino code. A parts list and PCB layout diagrams are provided. Instructions explain how to flash the bootloader before programming the microcontroller board from the Arduino IDE.

Uploaded by

Siam_Square
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
109 views5 pages

Analog Style VU Meter On OLED Display - Arduino Compatible

This document describes an analog-style VU meter project using a 0.96" OLED display and Arduino-compatible microcontroller. The project includes an audio input, potentiometer to adjust signal level, and OLED display driven by Arduino code. A parts list and PCB layout diagrams are provided. Instructions explain how to flash the bootloader before programming the microcontroller board from the Arduino IDE.

Uploaded by

Siam_Square
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Analog Style Mono VU Meter On OLED - Arduino Compatible

This is an analog-style VU meter on a 0.96ʺ OLED Display. The project has a 0.96ʺ OLED display, Atmega328 Microcontroller, 3.5 mm audio EP socket for
audio signal input. This Arduino compatible hardware can be program using Arduino IDE. Operating Supply 5V DC.

· CN4 or CN3: Audio Signal Input (From Headphone or Audio Signal)


· PR1 Trimmer Potentiometer: Audio Signal Level Adjust
· CN2: Programming Connector
· CN1: OLED Disapply 0.96 Inch – 4 Pin

Arduino code is available as a download to test the project. A new ATMEGA328 chip is required to bootloader flashing before programming the
microcontroller with Arduino IDE. For more info check the link below:

https://www.arduino.cc/en/Tutorial/BuiltInExamples/ArduinoToBreadboard

Credits: Arduino Code Author Mirko Pavleski


https://create.arduino.cc/projecthub/mircemk/diy-analog-style-stereo-vu-meter-on-i2c-oled-00aca7

www.rajkumarsharma.com
www.electronics-lab.com Author Rajkumar Sharma 0 7 0 0 5
www.electronics-lab.com Author Rajkumar Sharma www.twovolt.com
0 7 0 0 5
0.96INCH OLED
D13
D12
D11
VCC
GND
RESET
RX
TX

AUDIO INPUT
LEVEL ADJUST

MONO AUDIO IN

BOM
NO. QNTY. REF. DESC. MANUFACTURER SUPPLIER SUPPLIER PART NO
1 1 CN1 4 PIN MALE HEADER PITCH 2.54MM WURTH DIGIKEY 732-5317-ND
2 1 CN2 8 PIN MALE HEADER PITCH 2.54MM WURTH DIGIKEY 732-5321-ND
3 1 CN3 OPTIONAL
4 1 CN4 3.5MM FEMALE EP SOCKET CLIFF Element14 2518188
5 2 C1,C3 0.1uF/50V SMD SIZE 0805 MURATA/YAGEO DIGIKEY
6 1 C2 10uF/10V SMD SIZE 0805 MURATA/YAGEO DIGIKEY
7 2 C5,C6 22PF/50V SMD SIZE 0805 MURATA/YAGEO DIGIKEY
8 1 C7 10uF/16V SMD SIZE 1210 OR 1206 MURATA/YAGEO DIGIKEY
9 1 D1 1N4148 MICROCHIP TECH DIGIKEY 1086-15170-ND
10 1 PR1 10K TRIMMER POT NIDEC COPAL DIGIKEY CT6EP103-ND
11 1 R2 0E SMD SIZE 0805 MURATA/YAGEO DIGIKEY
12 1 R3 1M 5% SMD SIZE 0805 MURATA/YAGEO DIGIKEY
13 2 R4,C4 DNI DIGIKEY DO NOT INSTALL
14 1 U1 ATMEGA328TQPF-32 MICROCHIP DIGIKEY ATMEGA328PB-AURCT-ND
15 1 X1 16Mhz ECS INC DIGIKEY X1103-ND
16 1 R1 10K 5% SMD SIZE 0805 MURATA/YAGEO DIGIKEY
17 1 OLED BLUE 0.96" OLED Display I²C 4-PIN ALIEXPRESS

www.electronics-lab.com Author Rajkumar Sharma www.twovolt.com


0 7 0 0 5
SILK SCREEN TOP SILK SCREEN BOTTOM BOTTOM LAYER TOP LAYER

PCB DIMENSIONS 40.48MM X 27.31MM

www.electronics-lab.com Author Rajkumar Sharma www.twovolt.com


0 7 0 0 5
Boot-Loader Connections

D13
D12
D11
VCC
GND
ATMEGA328
RESET
RX
TX

Arduino Programming Connections

D13
D12
NO-ATMEGA328

D11
VCC
GND
RESET
RX
TX

www.electronics-lab.com Author Rajkumar Sharma www.twovolt.com


0 7 0 0 5

You might also like