STZ-P80C Intelligent Digital Pressure Switch

1, Technical Parameters
Pressure Range -1bar...0-1bar...6bar...600bar
Accuracy 1%FS
Power Supply 12VDC;24VDC;220VAC;380VAC(Optional)
Alarm Point Setting Can set any point in the full scale
Output Signal Relay output
Overload Capacity 380V 3A; 220V 5A; 24V 5A
Using Temperature -20℃~ 80℃
Measurement Medium Which is compatible with 316L stainless steel
WireConnection Portection Protection for reversed polarity and short circuit
Installation Connection M20*1.5; G1/2; G1/4;NPT1/4(Optional)
Connection Wires Power line:red and blue; output line:black and white

2, Button Description
1.(ON/OFF)Run Button:run button for system,should close this button when you
want to do the parameter setting,if not,it won't save the setting;
2.(SET)Setting Button:press SET button shortly to be into the upper and lower
limit value setting,press SET button for 3 seconds to be into the system setting;
3.(▲)Increase Value Button:press one time the value will increase into
0.01Mpa,press for 2 seconds will increase into 0.1Mpa;
4.(▼)Decrease Value Button:press one time the value will decrease into
0.01Mpa,press for 2 seconds will decrease into 0.1Mpa;

3, Using Method
1.The method for setting the controlled pressure
(1)press ON/OFF run button shortly,and then the run light and the pressure
control system will be closed;
(2)Setting for the upper and lower limit value
Press SET button shortly,then be into the lower limit value setting(right now the
light of the DOWN is open),and then through (▲)(▼) button to increase or decrease
the value,after done the setting,press SET button again to be into the upper limit value
setting(right now the light of the UP is open),and then through (▲)(▼) button to
increase or decrease the value;
(3)Done all setting,press SET button to save it(after setting some value,the system
will save it automatically if have not any button operation for 5 seconds)
(4)Press ON/OFF run button again(the run light is on),the switch will work.
2.Change the Unit: press ON/OFF run button to close the run light,you press ▲
to choose your unit(MPa; kgf/cm2; PSI), press for one time the unit will be MPa, press
for two times the unit will be kgf/ cm2, press for three times the unit will be PSI,after
setting,start the run light;
3.The function for zero clearing: press ON/OFF run button to close the run
light,and then press (▼) button for 5 seconds to change the current value into zero
point,after done the setting,press ON/OFF run button.(when you do this setting,the
pressure switch should not under any press condition)

4, System Function Mode

Press SET button for 3 seconds to be into the system setting,and press SET
button again to display the following function mode circularly;
Done all function setting,should press ON/OFF run button to save all setting.
 Function Mode Function Description Function Setting Method
Start it:the relay will close up for
Avoid the motor from After being to the system
Power-on Self-test 1 minute after open the
staring continually as the setting,press (▲) or (▼) to
R001/ R000
R001 system,during this time,the relay
pressure in the pump is start or close the
Close
Close/Start still close up if have pressure
changeable momentarily function,it's the windows
which exceeds the upper limit
when start the motor default which is underline.
setting value.
Prevent the motor from
Start it:the controller can't check running idle as the
Check pressure the pressure change within 3 measurement pressure
After being to the system
automatically minutes after the relay closes can't reach to the upper
setting,press (▲) or (▼) to
S0011/S000
S00 up,and then will cut off the relay limit setting value
start or close the function
Close
Close/Start automatically and display E--1 because of draining the
on the display and alarm. water or leaking pressure
on the pump.
Start it:when pressure is more
Remind of pressure of
than (upper limit
the controlling system
value+0.1Mpa),will cut off the
Over-pressure reaches to the figure
relay,and will alarm and display After being to the system
Checking which is more than the
E--2 on screen;when pressure is setting,press (▲) or (▼) to
N001
N001/N000 upper limit value,please
less than (upper limit start or close the function
Close
Close/Start check out whether has
value+0.1Mpa),the alarm won't
some problem with the
work,and controller will work
system or not.
again.
After being to the
system,press (▲) or (▼) to
change H001 into H000,and
Start it:when the pressure After setting the delay
press SET button shortly to
Delay time for reaches to the setting value,the time for controlling,will
display"0010",and then
Controlling controller won't work avoid the motor from
through (▲)(▼) button to
H001
H001/H000 immediately,will get the delay working continually
set the value you want,the
Close
Close/Start time and then work,and can set when the pipe has the
unit is second,the window
the delay time. unstable pressure.
default is 10 seconds,after
done the setting,press SET
button to save it.
After being to the
system,press (▲) or (▼) to
change P001 into P000,and
when display "----",through
(▲) button to input the
Start it:press any button except
Parameter password,and through SET
for ON/OFF button,the screen
Protection To protect the parameters button to move the place(for
will display “----”,right now
P001
P001/P000 from revising. the next words),if the
should input the password to do
Close
Close/Start password is“1111”,and then
any setting.
press SET button to make
sure,when system starts
again,will be into the
password protection
automatically.
definition:““*00
Note: function definition: *0011” (close the mode
mode));“*00
*0000” (start the mode
mode)),it's the
windows default which is underline.