Setup Guide

WARNING:
Drum key can be pinched when adjusting clamps with drum key. Operate carefully.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. May injure your fingers.

1 Check the include items

CYMBAL PADS BOX EXTENDED PADS BOX HI-HAT PEDAL BOX
Cymbal Pad for Hi-Hat Cymbal Pad for Crash1 Cymbal Pad for Ride Cymbal Pad for Crash2
(with Choke) (with Choke)

DRUM PADS BOX DRUM MODULE BOX

1~3 4

ACCESSORIES BOX KICK PEDAL BOX

Hi-Hat Holder Drum Key Pad Mount X 5 Drumsticks

Handscrews X 2 Hexagon Key Connection Cable X 11 AC Adaptor

Owner’s Manual Setup Guide

STAND AND CYMBAL HOLDER BOX

Center Pipe (1)

Center Pipe (2)

Side Arm (R)

Side Arm (L1)

Side Arm (L2)

Pillar (L1) Pillar (R1) Pillar (L2) Pillar (R2) Cymbal Holder(L) Cymbal Holder (R) X 2
 2 Set Up the Stand

Center Pipe (1) Side Arm (L1)

Pillar (L1)
Pillar (R1)
Center Pipe (2)

Pillar (L2)

1 2 3 4 5

Side Arm (R)

Pillar (R2)
Side Arm (L2)

6 7 8

1. Attach the Center Pipe (1) to the clamp on the Pillar (L1).
2. Attach the Center Pipe (2) to the clamp on the Pillar (L1).
3. Attach the Center Pipe (1) & (2) to the clamps on the Pillar (R1).
4. Attach the Side Arm (L1) to the clamp on the Pillar (L2).
5. Attach the Side Arm (L1) to the clamp on the Pillar (L1).
6. Attach the Side Arm (R) to the clamp on the Pillar (R2).
7. Attach the Side Arm (R) to the clamp on the Pillar (R1).
8. Attach the Side Arm (L2) to the clamp on the Pillar (L1).

Note:
Loosen or tighten the screws on the clamp with drum key as shown partial enlargement.
Adjust the height of the Side Arms with drum key as needed.

Wing Nut 1

Wing Nut 2

9 10

9. Attach the pad mounts to the mount holders on 10. Insert the two cymbal holders into the holders on
the Center Pipe (1), Side Arm (L2), Side Arm (R ), the Pillars, attach the hi-hat holder to mount
and firmly tighten the respective wing nuts 1. holders on the Side Arm (L1), and firmly tighten
the respective wing nuts .
Note:
Loosen or tighten the wing nuts on the mount Note:
holder as shown partial enlargement. Loosen or tighten the wing nuts on the mount
Move the mount holders as needed, and firmly holder as shown partial enlargement.
tighten the respective wing nuts 2.
3 Attach the Parts
Attach the Pads

1. Loosen the wing nuts on the drum pads. Wing Nut Tom 1 Tom 2

2. Attach the drum pads to the pad mounts,

and firmly tighten the wing nuts on the 1 Tom 3
drum pads. Tom 4
Snare

Attach the Cymbal Pads

Slot
Tap
Crash 1
1. Remove the wing nut and felt Ride
washer from the cymbal tilter.
Wing Nut 3
2. Place the cymbal pad, felt Hi-Hat Crash 2
washer, wing nut 3 assembly as
Felt Washer
shown, and tighten the wing nut
3 to obtain an appropriate
amount of sway.
Wing Nut 4
3. Adjust the cymbal pad position Hexagon
with the wing nut 4. Key

Note: Cymbal Tilter

Put the cymbal on the cymbal

adapter and locate the tap of 2 3
the adapter in the slot ofthe
cymbalbottom 1

Tightentheboltwiththe
hexagonkey asshown
partial enlargement

Assemble the Kick

1. Insert the beater to the beater holder on

the foot pedal.
1 2 3
2. Adjust the beater position and tighten
the beater with the drum key.

3. Attach the foot pedal to the kick pad.

4. Adjust the beat position and tighten the

wing nut.

Note:
Position the one beater in the center
of the kick pad or the two beaters
equally apart from the center of the kick
4
pad as shown.

Wing Nut
4 Connect the Pads to the Drum Module

Attach the Drum Module

1. Connect the cable to the drum module as shown with

handscrews.

2. Attach the drum module to the mount holders on Side

Arm (L1), and firmly tighten the relevant wing nut. 2

Note: 1
Adjust the drum module position by moving the mount
holders as needed, and firmly tighten the relevant wing
nut.

Connection Procedure

Make connections as shown in the illustration.

Crash 1 Ride

Crash 2
Hi-Hat
Tom1 Tom2
Tom 4

Drum
Tom3
Module
Snare Tom4

Kick

Hi-Hat Crash 1 Ride

Pedal

Hi-Hat
Tom 1 Tom 2
Crash 2

Drum Module

Tom 3

Tom 4
Snare

1. Place the kick on the floor in the center of the rack as

shown.

2. Place the hi-hat pedal on the floor on your left side.

3. Connect the pads to the drum module with the marked

cables.

Are you ready? Let's enjoy playing it.

Hi-Hat Control
Kick

DD514_G05