14A7A3ZW099

Operator’s Manual
Turn Tight® Extreme Rider

26 HP, 54” MOWER DECK
Model No. 247.204450
• Espanol, P. 35
THIS product has a low emission engine which operates differently from
previously built engines. Before you start the engine, read and understand
this Operator’s Manual.
CAUTION For answers to your questions about

this product, call:
Before using this equipment,
read this manual and follow 1-888-331-4569
all safety rules and operating Customer Care Hot Line
instructions.
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

Visit our website: www.craftsman.com Form No. 769-10493
(January 8, 2015)
TABLE OF CONTENTS
Warranty Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Service and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Off-Season Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Slope Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Español. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Service Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARRANTY STATEMENT
CRAFTSMAN LIMITED WARRANTY
FOR TWO YEARS from the date of purchase, all non-expendable parts of this riding equipment are warranted against defects in material or workmanship. With proof of purchase, a defective
non-expendable part will receive free repair or replacement at option of seller.
BATTERY LIMITED WARRANTY
FOR 90 DAYS from the date of purchase, the battery (an expendable part) of this riding equipment is warranted against defects in material or workmanship. With proof of purchase, you will
receive a new battery at no charge. You are responsible for the labor cost of battery installation.
ADDITIONAL LIMITED WARRANTIES
In the following additional warranties, you are responsible for the labor cost of part installation after the second year from the date of purchase.
FOR FIVE YEARS from the date of purchase, the frame of this riding equipment is warranted against any defects in material or workmanship. With proof of purchase, you will receive a new
frame at no charge.
FOR TEN YEARS from the date of purchase, the front axle of this riding equipment is warranted against any defects in material or workmanship. With proof of purchase, you will receive a new
axle at no charge.
FOR AS LONG AS IT IS USED by the original owner after the tenth year from the date of purchase, the cast iron front axle (if equipped) of this riding equipment is warranted against any defects
in material or workmanship. With proof of purchase, you will receive a new cast iron front axle at no charge.
WARRANTY SERVICE
For warranty coverage details to obtain free repair or replacement, visit the web page: www.craftsman.com/warranty
Product Replacement
If part repair or replacement is impossible, you will receive a new riding equipment unit of the same or equivalent model.
Warranty Restriction
All warranty coverage is void if this riding equipment is ever used while providing commercial services or if rented to another person.
This warranty covers ONLY defects in material and workmanship. Warranty coverage does NOT include:
• Expendable parts (except battery) that can wear out from normal use within the warranty period, including but not limited to blades, spark plugs, belts and air, oil or gas filters.
• Standard maintenance servicing, oil changes or tune-ups.
• Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass.
• Tire or wheel replacement or repair resulting from normal wear, accident, or improper operation or maintenance.
• Repairs necessary because of operator abuse, including but not limited to damage caused by towing objects beyond the capability of the riding equipment, impacting objects that
bend the frame, axle assembly or crankshaft, or over-speeding the engine.
• Repairs necessary because of operator negligence, including but not limited to, electrical and mechanical damage caused by improper storage, failure to use the proper grade and
amount of engine oil, failure to keep the deck clear of flammable debris, or failure to maintain the riding equipment according to the instructions contained in the operator's manual.
• Engine (fuel system) cleaning or repairs caused by fuel determined to be contaminated or oxidized (stale). In general, fuel should be used within 30 days of its purchase date.
• Normal deterioration and wear of the exterior finishes, or product label replacement.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
PRODUCT SPECIFICATIONS MODEL NUMBER

Model Number _________________________________
Engine Oil: SAE 30
Serial Number __________________________________
Fuel: Unleaded Gasoline
Date of Purchase ________________________________
Record the model number, serial number,
and date of purchase above.
© Sears Brands, LLC 2
SAFETY INSTRUCTIONS
WARNING DANGER
This symbol points out important safety instructions which, if not This machine was built to be operated according to the safe operation
followed, could endanger the personal safety and/or property of practices in this manual. As with any type of power equipment,
yourself and others. Read and follow all instructions in this manual carelessness or error on the part of the operator can result in serious injury.
before attempting to operate this machine. Failure to comply with these This machine is capable of amputating fingers, hands, toes and feet and
instructions may result in personal injury. When you see this symbol, HEED throwing debris. Failure to observe the following safety instructions could
ITS WARNING! result in serious injury or death.
WARNING WARNING
CALIFORNIA PROPOSITION 65 Your Responsibility—Restrict the use of this power machine to
persons who read, understand and follow the warnings and instructions in
Engine Exhaust, some of its constituents, and certain vehicle components
this manual and on the machine.
contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm. SAVE THESE INSTRUCTIONS!
Battery posts, terminals, and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and
reproductive harm. Wash hands after handling.
GENERAL OPERATION • Be aware of the mower and attachment discharge direction and do not point
• Read, understand, and follow all instructions on the machine and in the it at anyone. Do not operate the mower without the discharge cover or entire
manual(s) before attempting to assemble and operate. Keep this manual in grass catcher in its proper place.
a safe place for future and regular reference and for ordering replacement • Do not put hands or feet near rotating parts or under the cutting deck.
parts. Contact with the blade(s) can amputate hands and feet.
• Be familiar with all controls and their proper operation. Know how to stop • A missing or damaged discharge cover can cause blade contact or thrown
the machine and disengage them quickly. object injuries.
• Never allow children under 14 years old to operate this machine. Children 14 • Stop the blade(s) when crossing gravel drives, walks, or roads and while not
years old and over should read and understand the operation instructions cutting grass.
and safety rules in this manual and should be trained and supervised by a
• Watch for traffic when operating near or crossing roadways. This machine is
parent.
not intended for use on any public roadway.
• Never allow adults to operate this machine without proper instruction.
• Do not operate the machine while under the influence of alcohol or drugs.
• To help avoid blade contact or a thrown object injury, keep bystanders,
• Mow only in daylight or good artificial light.
helpers, children and pets at least 75 feet from the machine while it is in
operation. Stop machine if anyone enters the area. • Never carry passengers.
• Thoroughly inspect the area where the equipment is to be used. Remove • Disengage blade(s) before shifting into reverse. Back up slowly. Always look
all stones, sticks, wire, bones, toys, and other foreign objects which could down and behind before and while backing to avoid a back-over accident.
be picked up and thrown by the blade(s). Thrown objects can cause serious • Slow down before turning. Operate the machine smoothly. Avoid erratic
personal injury. operation and excessive speed.
• Plan your mowing pattern to avoid discharge of material toward roads, • Disengage blade(s), set parking brake, stop engine and wait until the
sidewalks, bystanders and the like. Also, avoid discharging material against blade(s) come to a complete stop before removing grass catcher, emptying
a wall or obstruction which may cause discharged material to ricochet back grass, unclogging chute, removing any grass or debris, or making any
toward the operator. adjustments.
• Always wear safety glasses or safety goggles during operation and while • Never leave a running machine unattended. Always turn off blade(s), set
performing an adjustment or repair to protect your eyes. Thrown objects parking brake, stop engine and remove key before dismounting.
which ricochet can cause serious injury to the eyes.
• Use extra care when loading or unloading the machine into a trailer or truck.
• Wear sturdy, rough-soled work shoes and close-fitting slacks and shirts. This machine should not be driven up or down ramp(s), because the machine
Loose fitting clothes and jewelry can be caught in movable parts. Never could tip over, causing serious personal injury. The machine must be pushed
operate this machine in bare feet or sandals. manually on ramp(s) to load or unload properly.
• Muffler and engine become hot and can cause a burn. Do not touch.
3
SAFETY INSTRUCTIONS
• Check overhead clearances carefully before driving under low hanging tree Do Not:
branches, wires, door openings etc., where the operator may be struck or • Do not turn on slopes unless necessary; then, turn slowly and gradually
pulled from the machine, which could result in serious injury. downhill, if possible.
• Disengage all attachment clutches and depress the brake pedal completely • Do not mow near drop-offs, ditches or embankments. The mower could
before attempting to start engine. suddenly turn over if a wheel is over the edge of a cliff, ditch, or if an edge
• Your machine is designed to cut normal residential grass of a height no more caves in.
than 10”. Do not attempt to mow through unusually tall, dry grass (e.g., • Do not try to stabilize the machine by putting your foot on the ground.
pasture) or piles of dry leaves. Dry grass or leaves may contact the engine
• Do not use a grass catcher on steep slopes.
exhaust and/or build up on the mower deck presenting a potential fire
hazard. • Do not mow on wet grass. Reduced traction could cause sliding.
• Use only accessories and attachments approved for this machine by the • Do not attempt to coast downhill. Over-speeding may cause the operator to
machine manufacturer. Read, understand and follow all instructions lose control of the machine resulting in serious injury or death.
provided with the approved accessory or attachment. For a list of approved • Do not tow heavy pull behind attachments (e.g. loaded dump cart, lawn
accessories and attachments, call 1-888-331-4569. roller, etc.) on slopes greater than 5 degrees. When going down hill, the
• Data indicates that operators, age 60 years and above, are involved in a extra weight tends to push the tractor and may cause you to loose control
large percentage of riding mower-related injuries. These operators should (e.g. tractor may speed up, braking and steering ability are reduced,
evaluate their ability to operate the riding mower safely enough to protect attachment may jack-knife and cause tractor to overturn).
themselves and others from serious injury. CHILDREN
• If situations occur which are not covered in this manual, use care and good Tragic accidents can occur if the operator is not alert to the presence of children.
judgment. Children are often attracted to the machine and the mowing activity. They do not
understand the dangers. Never assume that children will remain where you last saw
SLOPE OPERATION
them.
Slopes are a major factor related to loss of control and tip-over accidents which can
result in severe injury or death. All slopes require extra caution. If you cannot back • Keep children out of the mowing area and in watchful care of a responsible
up the slope or if you feel uneasy on it, do not mow it. adult other than the operator.
For your safety, use the Slope Guide included as part of this manual to measure • Be alert and turn machine off if a child enters the area.
slopes before operating this machine on a sloped or hilly area. If the slope is greater • Before and while backing, look behind and down for small children.
than 15 degrees as shown on the Slope Guide, do not operate this machine on that
• Never carry children, even with the blade(s) shut off. They may fall off and be
area or serious injury could result.
seriously injured or interfere with safe machine operation.
Do: • Use extreme care when approaching blind corners, doorways, shrubs, trees
• Mow up and down slopes, not across. Exercise extreme caution when or other objects that may block your vision of a child who may run into the
changing direction on slopes. machine.
• Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain • To avoid back-over accidents, always disengage the cutting blade(s) before
could overturn the machine. Tall grass can hide obstacles. shifting into Reverse. If equipped, the “Reverse Caution Mode” (blades
• Use slow speed. Choose a low enough speed setting so that you will not have operate while machine rides in reverse) should not be used when children or
to stop or shift while on the slope. Tires may lose traction on slopes even others are around.
though the brakes are functioning properly. Always keep machine in gear • Keep children away from hot or running engines. They can suffer burns from
when going down slopes to take advantage of engine braking action. a hot muffler.
• Follow the manufacturer’s recommendations for wheel weights or • Remove key when machine is unattended to prevent unauthorized
counterweights to improve stability. operation.
• Use extra care with grass catchers or other attachments. These can change Never allow children under 14 years of age to operate this machine. Children 14 and
the stability of the machine. over should read and understand the instructions and safe operation practices in
• Keep all movement on the slopes slow and gradual. Do not make sudden this manual and on the machine and should be trained and supervised by an adult.
changes in speed or direction. Rapid engagement or braking could cause
TOWING
the front of the machine to lift and rapidly flip over backwards which could
cause serious injury. • Tow only with a machine that has a hitch designed for towing. Do not attach
towed equipment except at the hitch point.
• Avoid starting or stopping on a slope. If tires lose traction, disengage the
blade(s) and proceed slowly straight down the slope. • Follow the manufacturers recommendation for weight limits for towed
equipment and towing on slopes.
• Never allow children or others in or on towed equipment.
4
SAFETY INSTRUCTIONS
• On slopes, the weight of the towed equipment may cause loss of traction and • Periodically check to make sure the blades come to complete stop within
loss of control. approximately (5) five seconds after operating the blade disengagement
• Always use extra caution when towing with a machine capable of making control. If the blades do not stop within the this time frame, your machine
tight turns (e.g. “zero-turn” ride-on mower). Make wide turns to avoid should be serviced professionally by a Sears or other qualified service dealer .
jack-knifing. • Check brake operation frequently as it is subjected to wear during normal
• Travel slowly and allow extra distance to stop. operation. Adjust and service as required.
• Do not coast downhill. • Check the blade(s) and engine mounting bolts at frequent intervals for
proper tightness. Also, visually inspect blade(s) for damage (e.g., excessive
SERVICE wear, bent, cracked). Replace the blade(s) with the original equipment
Safe Handling of Gasoline: manufacturer’s (O.E.M.) blade(s) only, listed in this manual. Use of parts
To avoid personal injury or property damage use extreme care in handling which do not meet the original equipment specifications may lead to
gasoline. Gasoline is extremely flammable and the vapors are explosive. improper performance and compromise safety!
Serious personal injury can occur when gasoline is spilled on yourself or your • Mower blades are sharp. Wrap the blade or wear gloves, and use extra
clothes which can ignite. Wash your skin and change clothes immediately. caution when servicing them.
• Use only an approved gasoline container. • Keep all nuts, bolts, and screws tight to be sure the equipment is in safe
• Never fill containers inside a vehicle or on a truck or trailer bed with a plastic working condition.
liner. Always place containers on the ground away from your vehicle before • Never tamper with the safety interlock system or other safety devices. Check
filling. their proper operation regularly.
• When practical, remove gas-powered equipment from the truck or • After striking a foreign object, stop the engine, disconnect the spark plug
trailer and refuel it on the ground. If this is not possible, then refuel such wire(s) and ground against the engine. Thoroughly inspect the machine for
equipment on a trailer with a portable container, rather than from a gasoline any damage. Repair the damage before starting and operating.
dispenser nozzle.
• Never attempt to make adjustments or repairs to the machine while the
• Keep the nozzle in contact with the rim of the fuel tank or container opening engine is running.
at all times until fueling is complete. Do not use a nozzle lock-open device.
• Grass catcher components and the discharge cover are subject to wear
• Extinguish all cigarettes, cigars, pipes and other sources of ignition. and damage which could expose moving parts or allow objects to be
• Never fuel machine indoors. thrown. For safety protection, frequently check components and replace
immediately with original equipment manufacturer’s (O.E.M.) parts only,
• Never remove gas cap or add fuel while the engine is hot or running. Allow
listed in this manual. Use of parts which do not meet the original equipment
engine to cool at least two minutes before refueling.
specifications may lead to improper performance and compromise safety!
• Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of
• Do not change the engine governor settings or over-speed the engine. The
filler neck to allow space for fuel expansion.
governor controls the maximum safe operating speed of the engine.
• Replace gasoline cap and tighten securely.
• Maintain or replace safety and instruction labels, as necessary.
• If gasoline is spilled, wipe it off the engine and equipment. Move machine to
• Observe proper disposal laws and regulations for gas, oil, etc. to protect the
another area. Wait 5 minutes before starting the engine.
environment.
• To reduce fire hazards, keep machine free of grass, leaves, or other debris
• According to the Consumer Products Safety Commission (CPSC) and the U.S.
build-up. Clean up oil or fuel spillage and remove any fuel soaked debris.
Environmental Protection Agency (EPA), this product has an Average Useful
• Never store the machine or fuel container inside where there is an open Life of seven (7) years, or 270 hours of operation. At the end of the Average
flame, spark or pilot light as on a water heater, space heater, furnace, clothes Useful Life, buy a new machine or have the machine inspected annually by
dryer or other gas appliances. a Sears or other qualified service dealer to ensure that all mechanical and
• Allow a machine to cool at least five minutes before storing. safety systems are working properly and not worn excessively. Failure to do
so can result in accidents, injuries or death.
General Service
• Never run an engine indoors or in a poorly ventilated area. Engine exhaust
contains carbon monoxide, an odorless, and deadly gas.
• Before cleaning, repairing, or inspecting, make certain the blade(s) and all
moving parts have stopped. Disconnect the spark plug wire and ground
against the engine to prevent unintended starting.
5
SAFETY INSTRUCTIONS
DO NOT MODIFY ENGINE SPARK ARRESTOR

To avoid serious injury or death, do not modify engine in any way. Tampering
with the governor setting can lead to a runaway engine and cause it to WARNING
operate at unsafe speeds. Never tamper with factory setting of engine This machine is equipped with an internal combustion engine and should
governor. not be used on or near any unimproved forest-covered, brushcovered or
grass-covered land unless the engine’s exhaust system is equipped with a
NOTICE REGARDING EMISSIONS spark arrestor meeting applicable local or state laws (if any).
Engines which are certified to comply with California and federal EPA
emission regulations for SORE (Small Off Road Equipment) are certified If a spark arrestor is used, it should be maintained in effective working
to operate on regular unleaded gasoline, and may include the following order by the operator. In the State of California the above is required by law
emission control systems: Engine Modification (EM), Oxidizing Catalyst (OC), (Section 4442 of the California Public Resources Code). Other states may have
Secondary Air Injection (SAI) and Three Way Catalyst (TWC) if so equipped. similar laws. Federal laws apply on federal lands.
A spark arrestor for the muffler is available through your nearest Sears Parts
and Repair Service Center.
WARNING: Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow
the warnings and instructions in this manual and on the machine.
SAVE THESE INSTRUCTIONS!
SAFETY SYMBOLS
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before
attempting to assemble and operate.
Symbol Description
READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to assemble and
operate
DANGER— ROTATING BLADES

Never carry passengers. Never carry children, even with the blades off.

Mowing in reverse is not recommended.
WARNING— ROTATING BLADES

Do not put hands or feet near rotating parts or under the cutting deck. Contact with the blade(s)
can amputate hands and feet.

Always look down and behind before and while backing to avoid a back-over accident.
WARNING—THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious personal injury.
6
SAFETY INSTRUCTIONS
Symbol Description
DANGER — SAFETY DEVICES

Keep safety devices (guards, shields, switches, etc.) in place and working.
BYSTANDERS
Keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in
operation.
WARNING— SLOPE OPERATION

Do not operate this machine on a slope greater than 15 degrees. Do not mow across slopes. Mow
up and down slopes no greater than 15 degrees. Avoid sudden turns. Use low speed. If machine
stops going uphill, stop blades and back down slowly.
WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during operation. Allow engine and
muffler to cool before touching.
DANGER — ROTATING BLADES

To reduce the risk of injury, keep hands and feet away. Do not operate unless discharge cover or grass
catcher is in its proper place. If damaged, replace immediately.
WARNING — FIRE HAZARD

Allow machine to cool before fueling or storing.

max10" Do not drive through piles of dry leaves or tall grass. Keep machine free of debris.

Operation of this equipment may create sparks that can start fires around dry vegetation. A spark
arrestor may be required. The operator should contact local fire agencies for laws or regulations
relating to fire prevention requirements. Do not allow debris to accumulate. The build up of debris
can lead to a fire.
7
15° Slope
15° Slope
(OK) (TOO STEEP)
Figure 1 Figure 2
8
SLOPE GAUGE
15° d
ashed
line
USE THIS SLOPE GAUGE TO DETERMINE
IF A SLOPE IS TOO STEEP FOR SAFE OPERATION!
To check the slope, proceed as follows:
1. Remove this page and fold along the dashed line.
2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.)
3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ).
4. Adjust gauge up or down until the left corner touches the slope (See Figure 1 and Figure 2).
5. If there is a gap below the gauge, the slope is too steep for safe operation (See Figure 2 above).
WARNING
Slopes are a major factor related to tip-over and roll-over accidents which can result in severe injury or death. Do not operate machine
on slopes in excess of 15 degrees. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not
mow it. Always mow up and down the face of slopes, never mow across the face of slopes.
ASSEMBLY
NOTE: All references in this manual to the left or right side and front or back of the Install Operator’s Seat (If necessary)
tractor are from the operating position only. Exceptions, if any, will be specified.
To install the seat proceed as follows:
Tractor Preparation NOTE: The seat is shipped with the seat switch and seat pan attached.
Manually Moving the Tractor 1. Cut any straps securing the seat assembly to the tractor. Remove any packing
material.
1. Engage the transmission bypass rod to move the tractor manually without
starting it. The transmission bypass rod is located on the rear of the tractor, NOTE: Be careful not to cut the wiring harness connecting the seat and the
on the frame. Engage the bypass rod by pulling out. See Figure 1. seat switch.
2. Remove the two shoulder screws and flange lock nuts in the seat pan as
shown in Figure 2.
Figure 1
NOTE: If the tractor will not move or does not move freely when pushing
check if the bypass lever is fully open or the brake is engaged. Figure 2
NOTE: The transmission will NOT engage when the hydrostatic bypass rod NOTE: Be sure that the nylon flange bearings (if equipped) remain in place
is pulled out. Return the rod to its normal position prior to operating the on the seat bracket mounting holes. If they come out during the removal of
tractor. If the tractor will not move when pushing on the forward/reverse the shoulders screws and flange lock nuts make sure to replace them before
pedals, or moves slowly, check to see of the bypass valve is on. installing the seat.
CAUTION
Never tow your tractor. Towing the tractor with the rear wheels on the
ground may cause severe damage to the transmissions.
2. Disengage the bypass rod by pushing the rod back in after moving the
tractor. See Figure 1.
9
ASSEMBLY
3. Rotate the seat into position and secure the seat into place with the Lower Deck Discharge Chute Deflector
previously removed shoulder screws and flange lock nuts. Be careful not to
crimp or damage the wire harness while installing the seat. See Figure 3. WARNING
Never operate the mower deck without the chute deflector installed and in
the down position.
Check the mower deck for a shipping brace that may be holding the chute deflector
upward for shipment. If the brace is present, it must be removed before operating
the tractor. Holding the chute deflector fully upward, remove the shipping brace.
Lower the chute deflector. See Figure 5.
Figure 3
4. Using the harness clip attached to the harness, secure the excess wire to the
fender by snapping the harness clip in place as shown in Figure 4.
Figure 5
Installing the Front Bumper

The hardware for attaching the front bumper is shipped installed into the bumper.
1. Remove the four hex screws from the bumper.
2. Position the bumper brackets to the inside of the tractor’s frame and secure
it in place with the four hex flange screws. See Figure 6.
Figure 4
Figure 6
10
ASSEMBLY
Adjusting the Seat 1. Remove the plastic cover, if present, from the positive battery terminal and
attach the red cable to the positive battery terminal (+) with the bolt and
WARNING hex nut. See Figure 8.
Before operating the tractor, make sure the seat is engaged in the seat-
stop. Engage the parking brake. Stand behind the machine and pull back
on seat until it clicks into place.
To adjust the position of the seat, lift the seat adjustment lever up. Slide the seat
forward or rearward to the desired position; then release the adjustment lever.
Make sure seat is locked into position before operating the tractor. See Figure 7.
Figure 8
2. Remove the plastic cover, if present, from the negative battery terminal and
attach the black cable to the negative battery terminal (–) with the bolt and
hex nut. See Figure 8.
3. Position the red rubber boot over the positive battery terminal to help
protect it from corrosion.
Figure 7
NOTE: If the battery is put into service after the date shown on top/side
Checking Tire Pressure of battery, charge the battery as instructed in the Service section your
Operator’s Manual prior to operating the tractor.
WARNING Setting the Deck Wheels
Equal tire pressure should be maintained at all times. Refer to the tire
sidewall for proper pressure. WARNING
The tires on your tractor may be over-inflated for shipping purposes. Reduce the tire Keep hands and feet away from the discharge opening of the cutting deck.
pressure before operating the tractor. Check the sidewall of tire for maximum p.s.i.
NOTE: The deck wheels are an anti-scalp feature of the deck and are not designed to
NOTE: Equal tire pressure is critical for level cutting deck performance. support the weight of the cutting deck.
Connecting the Battery Cables Move the tractor on a firm and level surface, preferably pavement, and proceed as follows:
1. Check the tire pressure, make sure the pressure is correct and equal on all tires.
WARNING
2. Make sure the deck is level, both front-to-back and side-to-side. See the
California Proposition 65 Warning: Battery posts, terminals, and related Maintenance & Adjustments section for deck leveling information and instructions.
accessories contain lead and lead compounds, chemicals known to the State of
California to cause cancer and reproductive harm. Wash hands after handling. 3. Select the height position of the cutting deck by placing the deck lift lever in
the normally desired mowing height setting.
CAUTION 4. Check the wheels for contact or excessive clearance with the surface below.
The deck wheels should have between ¼” and ½” clearance above the
When attaching battery cables, always connect the POSITIVE (Red) wire to ground. Proceed as follows to adjust the wheels:
its terminal first, followed by the NEGATIVE (Black) wire.
a. Raise the deck lift handle to its highest setting.
For shipping reasons, both battery cables on your equipment may have been left
disconnected from the terminals at the factory. To connect the battery cables,
proceed as follows:
NOTE: The positive battery terminal is marked Pos. (+). The negative battery
terminal is marked Neg. (–).
NOTE: If the positive battery cable is already attached, skip ahead to step 2. 11
ASSEMBLY
b. Remove the front and rear deck wheels by removing the flange lock Gas & Oil
nuts and shoulder bolts that secure them to the deck. See Figure 9.
The fuel tank is located at the outer/left of the dash and holds 3 gallons of gas.
Remove the fuel cap by turning it counter-clockwise. Use only clean, fresh (no more
than 30 days old), unleaded gasoline. Fill the tank no higher the bottom of the fill
neck to allow space for fuel expansion.
WARNING
Use extreme care when handling gasoline. Gasoline is extremely flammable and
the vapors are explosive. Never fuel the machine indoors or while the engine is
hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition.
NOTE: Your tractor is shipped with oil in the engine. However, you MUST
check the oil level before operating. See the Engine Operator’s Manual for
instructions on checking and adding oil. See the Service and Maintenance
section of this manual for oil changing procedures.
CAUTION
Always check the engine oil level before each use as instructed in the engine
operator’s manual. Add oil as necessary. Failure to do so may result in serious
damage to your engine.
Figure 9
c. Place the deck lift lever in the desired mowing height setting.
d. Reinsert the shoulder bolt (with each deck wheel) into the index
hole that leaves approximately ½-inch between the bottom of the
wheel and the pavement. Tighten the flange lock nut and shoulder
bolt to between 25-30 ft-lbs using a torque wrench.
NOTE: Refer to Adjusting the Deck in the Maintenance & Adjustments section of
this manual for more detailed instructions regarding various deck adjustments.
12
OPERATION
Fuel Tank Cap
Throttle/Choke Hour Meter

Control Lever Ignition Module
Forward Drive Pedal

PTO Switch
Reverse Drive Pedal
Brake Pedal
Park Brake/Cruise
Control Lever
Storage Tray
Deck Lift Lever
Cup Holder
Seat Adjustment Lever
Transmission
Bypass Rod
Figure 10
Now that you have set up your riding mower, it’s important to become acquainted Reverse Drive Pedal
with its controls and features. Refer to Figure 10.
The reverse drive pedal is located on the right side of the tractor along the running
NOTE: This Operator’s Manual covers several models. Tractor features may vary by board. Ground speed is also controlled with the reverse drive pedal. The further
model. Not all features in this manual are applicable to all tractor models and the downward the pedal is pivoted, the faster the tractor will travel. The pedal will
tractor depicted may differ from yours. return to its original/neutral position when it’s not pressed.
NOTE: References to LEFT, RIGHT, FRONT, and REAR indicate that position on the
tractor when facing forward while seated in the operator’s seat. Brake Pedal
The brake pedal is located on the left side of the tractor, along the running board.
WARNING The brake pedal can be used for stopping the tractor or setting the parking brake.
Read and follow all safety rules and instructions in this manual, including NOTE: The brake pedal must be fully depressed to activate the safety
the entire Operation section, before attempting to operate this machine. interlock switch when starting the tractor.
Failure to comply with all safety rules and instructions may result in
personal injury. Seat Adjustment Lever
Forward Drive Pedal The seat adjustment lever is located below the left of the seat. The lever allows for
adjustment forward or backward of the operator’s seat. Refer to the Assembly &
The forward drive pedal is located on the right side of the machine, along the Set-Up section for instructions on adjusting the seat position.
running board. Press the forward drive pedal forward to cause the tractor to travel
forward. Ground speed is also controlled with the forward drive pedal. The further
forward the pedal is pivoted, the faster the tractor will travel. The pedal will return
to its original/neutral position when it’s not pressed.
13
OPERATION
Throttle/Choke Control Lever Transmission Bypass Rod
The throttle/choke control lever is located on the left side of the The transmission bypass rod is located at the rear of the tractor on the lower right
tractor’s dash panel. This lever controls the speed of the engine and, section of the frame.
when pushed all the way forward, past the detent position closes the When engaged, the rod opens a bypass within the hydrostatic transmissions, which
choke for cold starting. When set in a given position, the throttle will allows the tractor to be pushed short distances by hand. Refer to the Assembly &
maintain a uniform engine speed. Set-Up section for instructions on using the bypass feature.
NOTE: When operating the tractor with the cutting deck
engaged, be certain that the throttle/choke control is always in Park Brake/Cruise Control Lever
the FAST position.
Deck Lift Lever

Located in the center of the tractor’s dash panel below the steering wheel, the park brake/
cruise control lever is used to engage the parking brake and the cruise control. Refer to the
Operation section of this manual for detailed instructions regarding the parking brake.
The lift lever is located in the right fender and is used to raise and lower the deck. NOTE: The parking brake must be set if the operator leaves the seat with the
Pull the handle to the left out of the index notch and push downward to lower the engine running or the engine will automatically shut off.
deck, or pull upward to raise the deck. When the desired height is attained, move NOTE: Cruise control can NOT be engaged at the tractor’s fastest ground
the lift handle to the right until fully in the index notch. speed.
Ignition Module
WARNING
WARNING Never leave a running machine unattended. Always disengage the PTO,
set the parking brake, stop the engine and remove the key to prevent
Never leave a running machine
unintended starting.
unattended. Always disengage PTO, set
parking brake, stop engine and remove LCD Service Minder & Hour Meter
key to prevent unintended starting.
When the ignition key is rotated out of the STOP position
To start the engine, insert the key into the but not into the START position, the LCD Service Minder
ignition switch and turn clockwise to the and Hour Meter will briefly display the battery voltage,
START position. Release the key into the followed by the tractor’s accumulated hours.
NORMAL MOWING MODE position once NOTE: Hours of tractor operation are recorded
the engine has fired. any time the ignition key is rotated out of the
To stop the engine, turn the ignition key counterclockwise to the STOP position. STOP position, regardless of whether the engine is started.
The LCD Service Minder will remind the operator of maintenance intervals for
CAUTION changing the engine oil, air filter service, low engine oil and low battery warnings.
Prior to operating the tractor, refer to both Safety Interlock Switches and
Starting The Engine in the Operation section of this manual for detailed Change Oil
instructions regarding the Ignition Switch Module and operating the The LCD will display the letters “CHG”, followed by the letters “OIL”, followed by the
tractor in REVERSE CAUTION MODE letters “SOON”, then finally followed by the meter’s accumulated time. “CHG/OIL/SOON/
TIME” will alternate on the display for 7 minutes after the meter reaches 50 hours. This oil
Power Take-Off (PTO) Switch service minder interval will occur every 50 hours. Before the interval expires, change the
The PTO switch is located on the dash panel to the right of the engine oil as instructed in the Maintenance section of the Engine Operator’s Manual
LCD Service Minder & Hour Meter. Low Oil (If so equipped)
Activating the PTO engages power to the cutting deck or other The letters “LO” followed by the letters “OIL”, then followed by the meter’s accumulated
(separately available) attachments. time will indicate the tractor is low on oil. When an engine is not running and
immediately after the engine is started the oil pressure may be low. This can trigger
the “LO” “OIL” text. This is normal. If the low oil indication persists stop the tractor
immediately and check the engine oil level as instructed in the Engine Operator’s Manual.
NOTE: The “LOW OIL” function only works if the engine is equipped with an
oil pressure switch.
14
OPERATION
Low Battery Starting the Engine
At startup, the battery voltage is briefly displayed then changes to accumulated
hours. The letters “LO” will display followed by the letters “BATT” and then followed WARNING
by the meter’s accumulated time. “LO/BATT/TIME” is displayed on the LCD when the Do not operate the tractor if the interlock system is malfunctioning. This
voltage drops below 11.5 volts. When this occurs, the battery is in need of a charge system was designed for your safety and protection.
or the engine’s charging system is not generating sufficient amperage. Charge the NOTE: Refer to the Assembly & Set-up section of this manual for Gasoline and Oil
battery as instructed in the Service section of this manual or have the charging fill-up instructions.
system checked by your local service dealer.
1. Insert the tractor key into the ignition switch module.
Air Filter Service 2. Place the PTO in the disengaged (OFF) position.
The letters “CLN” will display, followed by the letters “AIR”, followed by “FILT”, then
3. Fully engage the tractor’s brake.
followed by the meter’s accumulated time. “CLN/AIR/FILT/TIME” will alternate on
the display for 7 minutes after the meter reaches 50 hours. This air filter service 4. Move the throttle/choke control into the CHOKE position.
minder time interval will be every 50 hours. On intervals that are common with oil NOTE: If the engine is warmed up, it may not be necessary to choke the engine.
service, the oil message will be displayed first followed by the air filter message.
5. Turn the ignition key clockwise to the START position. After the engine
Operation starts, release the key. It will return to the NORMAL MOWING
position.
WARNING
CAUTION
Avoid serious injury or death. Go up and down slopes, not across. Avoid
sudden turns. Do not operate the tractor where it could slip or tip. If machine Do NOT hold the key in the START position for longer than ten seconds at a
stops going uphill, stop the PTO and back down the hill safely. Keep safety time. Doing so may cause damage to your engine’s electric starter.
devices (guards, shields and switches) in place and working. Remove objects 6. After the engine starts, move the throttle/choke control (if so equipped)
that could be thrown by the blades. Know the location and function of all down into the FAST position or push the choke control (if so equipped)
controls. Be sure the blades and the engine are stopped before placing hands down/in the OFF position.
or feet near blades. Before leaving the operator’s position, disengage the
NOTE: Do NOT leave the choke control on while operating the tractor. Doing
PTO, engage parking brake, shut off the engine and remove the key.
so will result in a “rich” fuel mixture and cause the engine to run poorly and
Safety Interlock Switches can damage the engine.
This tractor is equipped with a safety interlock system for the protection of the NOTE: When operating the tractor be certain that the throttle lever is always
operator. If the interlock system should ever malfunction, do not operate tractor. in the FAST position. Operating with the throttle at less than full throttle
Contact your authorized service dealer. may lead to shortened battery life.
• The safety interlock system prevents the engine from cranking or starting Stopping the Engine
unless the parking brake is engaged, and the PTO is in the DISENGAGED (OFF)
position. WARNING
• The engine will automatically shut off if the operator leaves the seat before If you strike a foreign object, stop the engine and disconnect the spark
engaging the parking brake. plug wire(s). Thoroughly inspect the machine for any damage. Repair the
• The PTO clutch will automatically shut off if the operator leaves the tractor’s damage before restarting and operating.
seat with the PTO in the ENGAGED (ON) position, regardless of whether the 1. If the blades are ENGAGED (ON), place the PTO in the DISENGAGED (OFF)
parking brake is engaged. position.
• With the ignition key in the NORMAL MOWING position, the PTO 2. Place the throttle near the SLOW position.
clutch will automatically shut off if the PTO is moved into the ENGAGED (ON) 3. Engage the parking brake.
position with the drive pedal in position for reverse travel.
4. Turn the ignition key counterclockwise to the STOP position.
WARNING 5. Remove the key from the ignition switch to prevent unintended starting.
Do not operate the tractor if the interlock system is malfunctioning. This system
was designed for your safety and protection.
15
OPERATION
Reverse Caution Mode Driving The Tractor
The REVERSE CAUTION MODE position of the ignition module allows the WARNING
tractor to be operated in reverse with the blades (PTO) engaged.
Avoid sudden starts, excessive speed and sudden stops.
NOTE: Mowing in reverse is not recommended.
1. Lightly press the brake pedal to release the parking brake. Move the throttle
WARNING into the FAST position.
Use extreme caution while operating the tractor in the REVERSE CAUTION 2. To travel FORWARD, slowly press the forward drive pedal forward until the
desired speed is achieved. See Figure 12.
MODE . Always look down and behind before and while backing.
Do not operate the tractor when children or others are around. Stop the
tractor immediately if someone enters the area.
Forward
To use the REVERSE CAUTION MODE :
NOTE: The operator MUST be seated in the tractor seat.
1. Start the engine as previously instructed on the previous page.
2. Turn the key from the NORMAL MOWING (Green) position to the
REVERSE CAUTION MODE (Yellow) position of the ignition module.
See Figure 11.
Reverse
Reverse
Indicator Push
Light Button
Reverse
Caution
Mode Normal Figure 12
Position Driving
Mode 3. To travel in REVERSE, check that the area behind is clear then slowly depress
the reverse drive pedal until the desired speed is achieved. See Figure 12.
Stop
position
CAUTION
Start Do NOT attempt to change the direction of travel when the tractor is in
position motion. Always bring the tractor to a complete stop before changing from
forward to reverse or vice versa.
WARNING
Figure 11 Do not leave the seat of the tractor without first placing the PTO in the
3. Press the REVERSE PUSH BUTTON at the top, right corner of the ignition DISENGAGED (OFF) position and engaging the parking brake. If leaving the
module. The red indicator light at the top, left corner of the ignition module tractor unattended, also turn the engine off and remove the ignition key.
will be ON while activated. See Figure 11.
4. Once activated (indicator light ON), the tractor can be driven in reverse with
the cutting blades (PTO) engaged.
5. Always look down and behind before and while backing to make sure no
children are around. After resuming forward motion, return key to the
NORMAL MOWING position.
6. The REVERSE CAUTION MODE will remain activated until:
a. The key is placed in either the NORMAL MOWING position or

STOP position or
b. The operator leaves the seat (electric PTO)/the parking brake is set
(manual PTO).
16
OPERATION
Driving On Slopes To disengage the cruise control, lightly press the forward drive pedal or the brake
pedal.
Refer to the SLOPE GAUGE on page 8 to help determine slopes where you may
operate the tractor safely. NOTE: Cruise control can not be set at the tractor’s fastest ground speed.
If the operator should attempt to do so, the tractor will automatically
WARNING decelerate to the fastest optimal mowing ground speed.
Do not mow on inclines with a slope in excess of 15 degrees (a rise of To change the direction of travel from forward to reverse when cruise control is
approximately 2-1⁄2 feet every 10 feet). The tractor could overturn and engaged, press the brake pedal to disengage and bring the tractor to a complete stop.
cause serious injury. Mow up and down slopes, NEVER across. Exercise Then slowly press the reverse drive pedal with the ball of your foot to travel in reverse.
extreme caution when changing direction on slopes. Watch for holes, ruts,
Using the Deck Lift Lever
bumps, rocks, or other hidden objects. Uneven terrain could overturn the
machine. Tall grass can hide obstacles. Avoid turns when driving on a slope. To raise or lower the cutting deck, move the lift lever to the left, then place it in the
If a turn must be made, turn down the slope. Turning up a slope greatly notch best suited for your application.
increases the chance of a roll over. Avoid stopping when driving up a slope. Operating the Headlights
If it is necessary to stop while driving up a slope, start up smoothly and
carefully to reduce the possibility of flipping the tractor over backward. The lamps are ON whenever the ignition key is rotated out of the STOP position.
The lamps turn OFF when the ignition key is moved to the STOP position.
Engaging the Parking Brake
Engaging the PTO (Electric PTO tractors)
NOTE: The parking brake must be set if the operator leaves the seat with the engine
running or the engine will automatically shut off. Engaging the PTO transfers power to the cutting deck or other (separately available)
attachments. To engage the PTO:
To set the parking brake:
1. Move the throttle to the FAST position.
1. Press the brake pedal completely down with your left foot and hold it in that
position. 2. Pull the PTO switch up/out into the engaged (ON) position. See Figure 13.
2. Press down on the parking brake/cruise control lever and hold it in that
position.
3. Remove your foot from the brake pedal.
4.
5.
Release pressure from the parking brake/cruise control lever.
After completing step 3, the brake pedal should remain in the down position. OFF
If it doesn’t, the parking brake is not engaged. Repeat steps 1-4 to engage.
To disengage the parking brake, lightly press the brake pedal.
WARNING
Never leave a running machine unattended. Always disengage the PTO,
unintended starting. ON
Setting The Cruise Control
WARNING
Never engage the cruise control lever while traveling in reverse.
Figure 13
To set the cruise control:
NOTE: When operating the tractor be certain that the throttle is always in
1. Slowly press the forward drive pedal with your right foot until the desired
the FAST position. Operating with the throttle at less than full throttle
speed is achieved.
may lead to premature battery wear and a poor quality cut.
2. Press down on the parking brake/cruise control lever and hold it in that
3. To disengage the PTO, push the PTO switch down/in to the disengaged (OFF)
position.
position.
3. Remove your foot from the forward drive pedal.
4. Release pressure from the parking brake/cruise control lever.
5. After completing step 3, the forward drive pedal should remain in the down
position and the tractor will maintain the same forward speed. If it doesn’t, the
cruise control is not engaged. Repeat steps 1-4 to engage the cruise control.
17
OPERATION
Mowing
WARNING
Make certain the area to be mowed is free of debris, sticks, stones, wire or
other objects that can be thrown by the rotating blades.
NOTE: Do not engage the mower deck when lowered in grass. Premature wear and
possible failure of the belt and PTO clutch will result. Fully raise the deck or move to
a non-grassy area before engaging the mower deck.
1. Mow up and down slopes, not across.
2. Avoid turns when driving on a slope. If a turn must be made, turn down the
slope. Turning up a slope greatly increases the chance of a roll over.
3. Avoid stopping when driving up a slope. If it is necessary to stop while
driving up a slope, start up the slope smoothly and carefully to reduce the
possibility of flipping the tractor over backward
4. Place the throttle into the FAST position and engage the PTO.
5. Lower the mower deck to the desired height setting using the deck lift handle.
6. Slowly press the forward drive pedal with your right foot until the desired
speed is achieved.
NOTE: The speed of the tractor will affect the quality of the mower cut.
Mowing at full speed will adversely affect the cut quality. Control the ground
speed with forward drive pedal.
7. When approaching the other end of the strip, slow down or stop before turning.
8. Align the mower with an edge of the mowed strip and overlap approximately 3”.
9. Direct the tractor on each subsequent strip to align with a previously cut strip.
10. To prevent rutting or grooving of the turf, if possible, change the direction
that the strips are mowed by approximately 45° for the next and each
subsequent mowing.
WARNING
Be careful when crossing gravel paths or driveways. Disengage the PTO and
raise the deck to the highest position before crossing.
NOTE: When stopping the tractor for any reason while on a grass surface,
always:
• Make sure the drive pedal is in neutral.
• Engage the parking brake.
• Shut the engine off and remove the key.
• Doing so will minimize the possibility of having your lawn
‘‘browned’’ by hot exhaust from your tractor’s running engine.
18
SERVICE AND MAINTENANCE
MAINTENANCE SCHEDULE
Follow the maintenance schedule given below. This chart describes service guidelines
WARNING only. Use the Service Log column to keep track of completed maintenance tasks. To
Before performing any type of maintenance/service, disengage all controls schedule service from Sears Parts & Repair, call 1-888-331-4569.
and stop the engine. Wait until all moving parts have come to a complete
stop. Disconnect spark plug wire and ground it against the engine to
prevent unintended starting. Always wear safety glasses during operation
or while performing any adjustments or repairs.
Interval Item Service Service Log

Each use 1. Engine Cooling Fans 1. Check/Clean
2. Engine Oil 2. Check
3. Air Filter 3. Check
After first 5 hours 1. Engine Oil 1. Change (break-in period). See engine manual
Every 10 hours 1. Battery terminals 1. Clean
2. Hood/Dash panel louvers 2. Clean
3. Intake screen 3. Check/Clean
4. Blades 4. Check/Sharpen/Replace as needed
5. Tires 5. Check
6. Front wheels 6. Lube
7. Deck 7. Check/Clean
Every 25 hours 1. Deck wheels 1. Inspect and lube
2. Deck level/pitch 2. Check
3. Lubrication points 3. Grease
Every 50 hours 1. Belts and pulleys 1. Check for damage and wear
2. Engine Oil 2. Change (See engine manual)
3. Oil Filter 3. Replace (See engine manual)
4. Air Filter 4. Clean or change (See engine manual)
5. Fuel Filter 5. Replace (See engine manual)
Every 100 hours 1. Hardware 1. Check and secure
2. Spark plug condition/gap 2. Check (See engine manual)
Every season/Before storage 1. Engine Cooling Fans 1. Check/Clean
2. Battery terminals 2. Clean
3. Lubrication points 3. Grease
4. Hood/Dash panel louvers 4. Clean
5. Intake screen 5. Check/Clean
6. Blades 6. Check/Sharpen/Replace as needed
7. Tires 7. Check
8. Deck 8. Check/Clean
9. Deck wheels 9. Inspect and lube
10. Deck level/pitch\ 10. Check
11. Spark plug condition/gap 11. Check (See engine manual)
12. Engine Oil 12. Change (See engine manual)
13. Oil Filter 13. Replace (See engine manual)
Miscellaneous 1. Valve lashing (camshaft/valve 2. Check and adjust *
clearance) *
* -- Have this item performed by a qualified service dealer
19
NOTE: This Operator’s Manual covers several models. Tractor features may vary by 3. Place an appropriate oil collection container with at least a 2.5 quart capacity
model. Not all features in this manual are applicable to all tractor models and the below the opening of the oil drain tube, to collect the used oil. Remove the
tractor depicted may differ from yours. oil fill cap/dipstick from the oil fill tube.
4. Remove the oil drain hose from the clip on the left side of the frame. See
WARNING Figure 14.
Before performing any maintenance or repairs, disengage the PTO, set the
parking brake, stop the engine and remove the key to prevent unintended
starting.
Battery
WARNING
California Proposition 65 Warning! Battery posts, terminals, and related
accessories contain lead and lead compounds, chemicals known to the
State of California to cause cancer and reproductive harm. Wash hands
after handling.
The battery is sealed and is maintenance-free. Acid levels cannot be checked and
fluid can not be added.
• Always keep the battery cables and terminals clean and free of corrosive build-up.
• After cleaning the battery and terminals, apply a light coat of petroleum jelly
or grease to both terminals.
CAUTION
Figure 14
If removing the battery for cleaning, disconnect the NEGATIVE (Black) wire
from it’s terminal first, followed by the POSITIVE (Red) wire. When re- 5. Remove the oil drain hose plug from the end of the hose. See Figure 14. Drain
installing the battery, always connect the POSITIVE (Red) wire its terminal the engine oil into the collection container.
first, followed by the NEGATIVE (Black) wire. Be certain that the wires are 6. After draining the oil, wipe any residual oil from the oil drain hose. Replace
connected to the correct terminals; reversing them could result in serious the plug on the drain hose and fully tighten. Replace the oil drain hose into
damage to your engine’s alternating system. the clip and snap the clip to secure.
Engine 7. Replace the oil filter, and refill the engine with new oil as instructed in the
engine operator’s manual.
Refer to the Engine Operator’s Manual for all engine maintenance procedures and
8. To refill the oil, re-install the plug at the end of the tube and refer to the
instructions for checking and adding oil. See the Changing the Engine Oil section
engine operator’s manual for refilling instructions, oil type and amount.
below for oil changing procedures and instructions.
NOTE : Maintenance, repair, or replacement of the emission control devices
NOTE: If the “LOW OIL” text appears immediately after the engine is started
and systems which are being done at owner’s expense may be performed
the oil pressure may be low. This is normal. If the low oil indication persists
by any engine repair establishment or individual. Warranty repairs must be
stop the tractor immediately and check the engine oil level as instructed in
performed by an authorized dealer.
the Engine Operator’s Manual.
NOTE: The “Low Oil” function only works if the engine is equipped with an Hydrostatic Transmission
oil pressure switch.
The hydrostatic transmission is sealed at the factory and is maintenance-free. The
Changing the Engine Oil fluid level cannot be checked and the fluid cannot be changed.
WARNING Hydrostatic Neutral Adjustment

If the engine has been recently run, the engine, muffler and surrounding If the tractor creeps forward or rearward when neither the forward nor reverse
metal surfaces will be hot and can cause burns to the skin. Exercise caution pedal is depressed, contact your authorized dealer to have the neutral setting
to avoid burns. properly adjusted.
To complete an oil change, proceed as follows:
1. Run the engine for a short time to warm the engine oil. The oil will flow more
freely and carry away more impurities. Use care to avoid burns from hot oil.
2. Locate the oil drain hose on the left side of the engine.
20
Cleaning the Tractor 13. After cleaning your deck with the Smart Jet system, return to the operator’s
position and engage the PTO. Keep the cutting deck running for a minimum of
Any fuel or oil spilled on the machine should be wiped off promptly. Do NOT allow two minutes, allowing the underside of the cutting deck to thoroughly dry.
debris to accumulate around the cooling fins of the engine, the transmission’s
cooling fan or on any other part of the machine. Lubrication
Smart Jet
WARNING
Your tractor’s deck is equipped with two water ports on its surface as part of its
deck wash system. Before lubricating, repairing, or inspecting, always disengage the PTO,
Use the Smart Jet to rinse grass clippings from the deck’s underside and prevent the unintended starting.
buildup of corrosive chemicals. Complete the following steps AFTER EACH MOWING:
1. Drive the tractor to a level, clear spot on your lawn, near enough for your
Front Wheels
garden hose to reach. Each of the front wheel axles and rims is equipped with a grease fitting. See Figure
16 for the location of the grease fitting on the axles and Figure 17 for the location of
CAUTION the grease fitting on the rims. Lubricate with a No. 2 multi-purpose grease applied
with a grease gun after every 25 hours of tractor operation.
Make certain the tractor’s discharge chute is directed AWAY from people,
your house, garage, parked cars, etc.
2. Disengage the PTO, set the parking brake and stop the engine.
3. Thread the hose coupler (packaged with your tractor’s Operator’s Manual)
onto the end of your garden hose.
4. Attach the hose coupler to the water port on your decks surface. See Figure 15.
Figure 16
Figure 15
5. Turn the water on.
6. While sitting in the operator’s position on the tractor, start the engine and
place the throttle lever in the FAST position.
7. Move the tractor’s PTO into the engaged (ON) position.
8. Remain in the operator’s position with the cutting deck engaged for a minimum
of two minutes, allowing the underside of the cutting deck to thoroughly rinse.
9. Move the tractor’s PTO into the disengaged (OFF) position.
10. Turn the ignition key to the STOP position to turn the tractor’s engine off.
11. Turn the water off and detach the hose coupler from the water port on your
deck’s surface.
12. Repeat the steps on the other port. Figure 17
21
Deck Wheels 5. To lower the front of the deck, loosen the outer nut then loosen (thread
outward) the nut, away from the front hanger bracket. See Figure 18. When
The wheels on the deck are equipped with a grease fitting. Lubricate with a No.
proper adjustment is achieved, re-tighten the outer nut.
2 multi-purpose grease applied with a grease gun after every 25 hours of tractor
operation. Leveling the Deck (Side-to-Side)
Pivot Points & Linkage If the cutting deck appears to be mowing unevenly, a side to side adjustment can be
performed. Adjust if necessary as follows:
Lubricate all the pivot points on the drive system, parking brake and lift linkage at
least once a season with light oil. 1. With the tractor parked on a firm, level surface, place the deck lift lever in
the middle position and rotate both blades so that they are perpendicular
Adjustments with the tractor.
2. Measure the distance from the outside of the left blade tip to the ground
WARNING and the distance from the outside of the right blade tip to the ground. Both
Shut the engine off, remove the ignition key and engage the parking brake measurements taken should be equal. If they’re not, proceed to the next
before making adjustments. Protect your hands by using heavy gloves step.
when handling the blades. 3. Under the rear fenders inside the wheels there is a lift adjustment rod for
NOTE : Check the tractor’s tire pressure before performing any deck leveling each side of the deck. See Figure 19.
adjustments. Refer to Tires on page 11 for information regarding tire pressure.
Adjusting the Deck
Leveling the Deck (Front-To-Rear)
The front of the cutting deck is supported by a stabilizer bar that can be adjusted to
level the deck from front to rear. The front of the deck should be between 1⁄4-3⁄8”
lower than the rear of the deck. Adjust if necessary as follows:
1. Park the tractor on a firm, level surface and place the deck lift lever in the
middle position and rotate the blade nearest the discharge chute so that it is
parallel with the tractor.
2. Measure the distance from the front of the blade tip to the ground and the
rear of the blade tip to the ground. The front of the deck should be between
1⁄4-3⁄8” less than the rear of deck.
3. Determine the approximate distance necessary for proper adjustment and
proceed, if necessary.
4. To raise the front of the deck, loosen the outer nut then tighten (thread
inward) the nut against the front hanger bracket. See Figure 18. When
proper adjustment is achieved, re-tighten the outer nut to 25-30 ft.-lbs. Figure 19
4. Minor side-to-side adjustments should be made using primarily the left
adjustment rod.
5. To raise the left side of the deck, loosen the upper nut on the end of the
lift rod, then turn the lower nut clockwise. When the proper adjustment is
achieved, tighten the upper nut to secure in place. To lower the left side of
the deck, loosen the upper nut on the end of the lift rod, then turn the lower
nut counterclockwise. When the proper adjustment is achieved, tighten the
upper nut to 25-30 ft-lbs. to secure in place.
6. The deck is properly leveled when both blade tip measurements taken earlier
are equal.
Adjusting the Deck Height
The height of the deck can be adjusted to ensure that the setting on your deck
height lever is accurate. To adjust the deck height proceed as follows:
1. Park the tractor on a firm, level surface and place the deck lift lever in the
highest position(4”) and rotate the blade nearest the discharge chute so that
it is perpendicular with the tractor.
Figure 18
22
2. Measure the distance from the outside of the left blade tip to the ground Jump Starting
and the distance from the outside of the right blade tip to the ground. Both
measurements taken should be 4”. If they’re not, proceed to the next step. WARNING
3. Using the right and left lift rods, raise or lower the necessary side of the deck Never jump start a damaged or frozen battery. Be certain the vehicles do
until both sides are measured at 4” from the pavement. not touch, and ignitions are off. Do not allow cable clamps to touch.
Adjusting the Deck Wheels 1. Connect positive (+) cable to positive (+)post of your tractor’s discharged
battery.
WARNING 2. Connect the other end of the cable to the positive (+) post of the jumper
Keep hands and feet away from the discharge opening of the cutting deck. battery.
NOTE: The deck wheels are an anti-scalp feature of the deck and are not designed to 3. Connect the second cable negative (–) to the other post of the jumper
support the weight of the cutting deck. battery.
The deck wheels should be approximately 1⁄4-1⁄2” above the ground when the deck 4. Make the final connection on the engine block of the tractor, away from the
is set in the desired height setting. To adjust the deck wheels see the Assembly & battery. Attach to an unpainted part to assure a good connection.
Set-Up section for instructions.
CAUTION
Seat Adjustment
If the jumper battery is installed on a vehicle (i.e. car, truck), do NOT start
Refer to the Assembly & Set-Up section of this manual for seat adjustment instructions.
the vehicle’s engine when jump starting your tractor.
WARNING 5. Start the tractor (as instructed in the Operation section of this manual).
Before operating the tractor, make sure the seat is engaged in the seat- 6. Remove the jumper cables in reverse order of connection.
stop. Engage the parking brake. Stand behind the machine and pull back Charging
on seat until it clicks into place.
Parking Brake Adjustment WARNING
Batteries give off an explosive gas while charging. Charge the battery in a
If the tractor does not come to a complete stop when the brake pedal is completely
well ventilated area and keep away from an open flame or pilot light as on a
depressed, or if the tractor’s rear wheels can roll with the parking brake applied
water heater, space heater, furnace, clothes dryer or other gas appliances.
(and the hydrostatic relief valve open), the brake is in need of adjustment. See your
authorized service dealer to have the brake adjusted.
CAUTION
Wheel Alignment
When charging your tractor’s battery, use only a charger designed for 12V lead-
If your tractor pulls to one side or is out of alignment, a wheel alignment might acid batteries. Read your battery charger’s Owner’s Manual prior to charging
be necessary. Take your tractor to an authorized service dealer to have the wheels your tractor’s battery. Always follow its instructions and heed its warnings.
properly aligned.
If your tractor has not been put into use for an extended period of time, charge the
Service battery as follows:
Battery 1. Set your battery charger to deliver a max of 10 amperes.
2. If your battery charger is automatic, charge the battery until the charger
WARNING indicates that charging is complete. If the charger is not automatic, charge
California Proposition 65 Warning: Battery posts, terminals, and related for no fewer than eight hours.
accessories contain lead and lead compounds, chemicals known to the State of
California to cause cancer and reproductive harm. Wash hands after handling.
CAUTION
If removing the battery, disconnect the NEGATIVE (Black) wire from it’s
terminal first, followed by the POSITIVE (Red) wire. When reinstalling the
battery, always connect the POSITIVE (Red) wire its terminal first, followed
by the NEGATIVE (Black) wire.
23
Fuse 6. Looking at the cutting deck from the left side of the tractor, locate the bow-
tie pin on the rear left side of the deck. See Figure 21.
WARNING
Before servicing, repairing, or inspecting, always disengage PTO, set parking
brake, stop engine and remove key to prevent unintended starting.
A 20 AMP fuse is installed in your tractor’s wiring harness to protect the tractor’s
electrical system from damage caused by excessive amperage.
If the electrical system does not function, or your tractor’s engine will not crank,
check to be certain that the fuse has not blown. It is located under the seat,
attached to the POSITIVE (Red) wire leading to the battery.
CAUTION
Always use a replacement fuse with the same amperage capacity as the
blown fuse.
Relays and Switches
There are several safety switches in the electrical system. If a function of the safety
interlock system described earlier is not functioning properly, have the electrical
system checked by your authorized service dealer.
Cutting Deck Removal Figure 21
To remove the cutting deck, proceed as follows: 7. Remove the bow pin and slide the deck pin out of the deck lift arm. See Figure 21.
1. Place the PTO in the disengaged (OFF) position and engage the parking brake. 8. Repeat the above steps on the tractor’s right side.
2. Lower the deck by moving the deck lift lever into the bottom notch on the 9. Pull the bow-tie pin out of the front deck lift rod securing it to the deck. See
right fender. Figure 22. Slide the deck lift rod out of the front hanger bracket.
3. Working on the right side of the tractor, insert a 3⁄8” drive ratchet wrench, set
to tighten, into square hole found on the idler bracket. See Figure 20.
Insert Wrench Here

Figure 22
10. Move the deck lift lever into the top notch to raise the deck lift up and out of
Figure 20 the way.
4. Use the wrench to pivot the deck drive pulley forward. See Figure 20.
CAUTION
WARNING There is a certain amount of spring tension due to the weight of the deck. When
Avoid pinching injuries. Never place your fingers on the idler spring or removing the lift linkage from the deck the tension of the springs will go from the
between the belt and a pulley while installing the belt. deck to the deck lift handle and snap back.
5. Carefully remove the belt from around the PTO pulley. 11. Gently slide the cutting deck out from underneath the tractor.
24
Cutting Blades 4. To properly sharpen the cutting blades, remove equal amounts of metal
from both ends of the blades along the cutting edges, parallel to the trailing
edge, at a 25°- to 30° angle. Always grind each cutting blade edge equally to
WARNING
maintain proper blade balance. See Figure 24.
Shut the engine off and remove ignition key before removing the cutting
blade(s) for sharpening or replacement. Protect your hands by using heavy
gloves when grasping the blade.
WARNING
Periodically inspect the blade and/or spindle for cracks or damage,
especially after you’ve struck a foreign object. Do not operate the machine
until damaged components are replaced.
To remove the blades, proceed as follows.
1. Remove the deck from beneath the tractor, (refer to Cutting Deck Removal
earlier in this section) then gently flip the deck over to expose its underside.
2. Place a block of wood between the deck housing baffle and the cutting
blade to act as a stabilizer. See Figure 23.
Figure 24
CAUTION
If the cutting edge of the blade has previously been sharpened, or if any
metal separation is present, replace the blades with new ones.
WARNING
A poorly balanced blade will cause excessive vibration, may damage the
tractor and/or result in personal injury.
5. Test the blade’s balance using a blade balancer. Grind metal from the heavy
side until it balances evenly.
NOTE: When replacing the blade, be sure to install the blade with the side of
the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the
Figure 23 ground when the mower is in the operating position.
3. Remove the hex flange nut that secures the blade to the spindle assembly.
See Figure 23. CAUTION
Use a torque wrench to tighten the blade spindle hex flange nut to between
70 ft-lbs and 90 ft-lbs.
Changing the Deck Belt
WARNING
The V-belts found on your tractor are specially designed to engage and
disengage safely. A substitute (non-OEM) V-belt can be dangerous by
not disengaging completely. For a proper working machine, use factory
approved belts.
All belts on your tractor are subject to wear and should be replaced if any signs of wear
are present . To change or replace the deck belt on your tractor, proceed as follows:
1. Remove the deck as instructed earlier in this section under Cutting Deck Removal.
NOTE: On some decks it may be necessary to remove the spindle covers to
remove and/or install the new belt. To remove the spindle covers, remove
the screws securing them to the deck.
25
2. Loosen, but do not remove the flange lock nut on the left idler pulley. See 5. Retighten idler pulleys.
Figure 25. 6. Remount the spindle covers if removed after step 1.
7. Re-install the deck making sure the belt remains routed around the pulleys
as instructed.
8. Pull the right side of the belt and place the narrow V side of the belt into the
PTO pulley. See Figure 27.
Flange Lock Nut
Figure 25
3. Carefully remove the belt from around the idler pulleys and the spindle pulleys.
WARNING
Avoid pinching injuries. Never place your fingers on the idler spring or Figure 27
between the belt and a pulley while removing the belt.
9. While holding the belt and pulley together, rotate the pulley to the left.
4. Route the new belt as shown in Figure 26. Continue holding and rotating the pulley and belt until the belt is fully rolled
into the PTO pulley.
Changing the Transmission Drive Belt
Several components must be removed and special tools used in order to change
the tractor’s transmission drive belt. See a qualified service dealer to have the
transmission drive belt replaced.
Figure 26
NOTE: Use a 3⁄8” drive ratchet wrench as instructed in earlier steps when
routing the new belt.
26
OFF-SEASON STORAGE
WARNING
Never store garden riding mower with fuel in tank indoors or in poorly
ventilated areas where fuel fumes may reach an open flame, spark, or pilot
light as on a furnace, water heater, clothes dryer, or gas appliance.
Off-Season Storage 9. Lubricate all lubrication points.

10. Jack the mower up and store it on blocks to take the weight off of the tires.
Riding Mower Storage
If your riding mower is not going to be operated for an extended period of time Removing the Riding Mower from Storage
(thirty days to approximately six months), the riding mower should be prepared for 1. Check the engine oil.
storage. Store the riding mower in a dry and protected location. If stored outside, 2. Fully charge the battery, lower riding mower off blocks, and inflate the tires
cover the riding mower (including the tires) to protect it from the elements. The to the recommended pressure.
procedures outlined below should be performed whenever the riding mower is
3. Remove the spark plugs and wipe them off. Using the starter, crank the
placed in storage.
engine to pump the excess oil out of the spark plug holes. Replace the spark
1. Change the engine oil and filter following the instructions provided in the plugs and the ignition leads.
Engine Manual.
4. If drained before storing, fill the fuel tank with clean, fresh gasoline.
WARNING 5. Start the engine and allow to idle for a few minutes to ensure engine is
Never store the riding mower with fuel in the tank indoors or in poorly operating properly.
ventilated enclosures, where fuel fumes may reach an open flame, spark or 6. Drive the riding mower without a load to make certain all the riding mower
pilot light as on a furnace, water heater, clothes dryer, etc. systems are functioning properly.
2. Service the engine as instructed in the separate engine manual.
3. Engines stored between 30 and 90 days need to be treated with a gasoline
stabilizer such as STA-BIL® and engines stored over 90 days need to be
run empty of fuel to prevent deterioration and gum from forming in fuel system
or on essential carburetor parts. If the gasoline in your engine deteriorates
during storage, you may need to have the carburetor, and other fuel system
components, serviced or replaced.
WARNING
Drain fuel only into an approved container outdoors, away from an open
flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes, and other
sources of ignition prior to draining fuel.
4. Remove the spark plugs and pour approximately one ounce of oil into each
cylinder. Crank the engine one or two turns to spread the oil evenly on the
cylinder walls. Replace the spark plugs.
5. Clean the engine and the entire riding mower thoroughly.
NOTE: Use of a pressure washer or garden hose is not recommended to
clean your riding mower. They may cause damage to electrical components,
spindles, pulleys, bearings or the engine. The use of water will result in
shortened life and reduce serviceability.
6. Sharpen the blades so that the mower will be ready to use when needed.
7. Protect the metal surfaces. Repair scratches with the appropriate touch-up
spray paint. Brush a rust preventive oil on any unpainted surfaces including
the pulleys and blades. (Be careful not to get any oil on the drive belts.)
8. Clean and fully charge the battery, then disconnect the negative cable at
the battery to prevent possible discharge. Recharge the battery periodically
when in storage.
NOTE: Remove the battery if exposed to prolonged periods of sub-freezing
temperatures. Store in a cool, dry location where temperatures are above
freezing.
27
TROUBLESHOOTING
WARNING
Before performing any type of maintenance/service, disengage all
controls and stop the engine. Wait until all moving parts have come to
a complete stop. Disconnect spark plug wire and ground it against the
engine to prevent unintended starting. Always wear safety glasses during
operation or while performing any adjustments or repairs.
This section addresses minor service issues. To locate the nearest Sears Service Center or to schedule service, simply contact Sears
at 1-800-4-MY-HOME®.
Problem Cause Remedy

Engine fails to start 1. PTO/Blade Engage knob engaged. 1. Place knob in disengaged (OFF) position.
2. Parking brake not engaged. 2. Engage parking brake.
3. Spark plug wire disconnected. 3. Connect wire to spark plug.
4. Throttle control lever not in correct starting 4. Place Throttle lever to FAST position.
position.
5. Fuel tank empty, or stale fuel. 5. Fill tank with clean, fresh (less than 30 days old) gas.
6. Blocked fuel line. 6. Replace fuel line. See a Sears or other qualified
service dealer. Replace fuel filter. See the Service
and Maintenance section.
7. Faulty spark plug. 7. Clean, adjust gap or replace plug.
8. Engine flooded. 8. Crank engine with throttle in FAST position.
9. Fuse(s) blown. 9. Replace fuse.
Engine runs erratically 1. Tractor running with Choke activated. 1. Check that the electric choke is working. See a
Sears or other qualified service dealer.
2. Spark plug wires loose. 2. Connect and tighten spark plug wires.
3. Blocked fuel line or stale fuel. 3. Replace fuel line. See a Sears or other qualified
service dealer. Fill tank with clean, fresh gasoline
and replace fuel filter. See the Service and Mainte-
nance section.
4. Vent in gas cap plugged. 4. Clear vent or replace cap if damaged.
5. Water or dirt in fuel system. 5. Drain fuel tank. Refill with clean, fresh gasoline. See
the Service and Maintenance section.
6. Dirty air cleaner. 6. Clean or replace air cleaner paper element or clean
foam pre-cleaner.
28
TROUBLESHOOTING
Engine overheats 1. Engine oil level low 1. Fill engine with proper amount and type of oil.
2. Air flow restricted 2. Clean grass clippings and debris from around the
engine’s cooling fins and blower housing.
Engine hesitates at high RPMs 1. Spark plug gap set too close 1. Remove spark plug and adjust gap.
Engine idles poorly 1. Fouled spark plug 1. Replace spark plug and adjust gap.
2. Dirty air cleaner 2. Clean or replace air cleaner element and/or clean
pre-cleaner.
Excessive vibration 1. Cutting blades loose or unbalanced 1. Tighten blade and spindle. Balance blade.
2. Damaged, dull, or bent cutting blade 2. Replace blade.
Mower will not mulch grass 1. Engine speed too low. 1. Place Throttle control in FAST (rabbit) position.
2. Wet grass. 2. Do not mulch when grass is wet.
3. Excessively high grass. 3. Mow once at a high cutting height, then mow again
at desired height or make a narrower cutting swath.
4. Dull blade. 4. Sharpen or replace blade.
Uneven cut 1. Deck not leveled properly. 1. Perform side-to-side deck adjustment.
2. Dull blade. 2. Sharpen or replace blade.
3. Uneven tire pressure. 3. Check tire pressure in all four tires.
29
NOTES
30
(This page applicable in the U.S.A. and Canada only.)
Sears Brands Management Corporation (Sears), the California Air Resources Board (CARB)
and the United States Environmental Protection Agency (U.S. EPA)
Emission Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations)
EMISSION CONTROL WARRANTY COVERAGE IS APPLICABLE TO CERTIFIED ENGINES AND TO CERTIFIED MODEL YEAR 1997 AND LATER ENGINES WHICH ARE PURCHASED AND
PURCHASED IN CALIFORNIA IN 1995 AND THEREAFTER, WHICH ARE USED IN CALIFORNIA, USED ELSEWHERE IN THE UNITED STATES (AND AFTER JANUARY 1, 2001 IN CANADA).
California and United States Emission Control Defects Warranty Statement
The California Air Resources Board (CARB), U.S. EPA and Sears are pleased to explain the control system on your engine for the periods of time listed below, provided there has
Emission Control System Warranty on your model year 2000 and later small off-road been no abuse, neglect or improper maintenance of your small off-road engine. Your
engine (SORE). In California, new small off-road engines must be designed, built and emission control system includes parts such as the carburetor, air cleaner, ignition
equipped to meet the State’s stringent anti-smog standards. Elsewhere in the United system, muffler and catalytic converter. Also included may be connectors and other
States, new non-road, spark-ignition engines certified for model year 1997 and later emission related assemblies. Where a warrantable condition exists, Sears will repair
must meet similar standards set forth by the U.S. EPA. Sears must warrant the emission your small off-road engine at no cost to you including diagnosis, parts and labor.
Sears Emission Control Defects Warranty Coverage
Small off-road engines are warranted relative to emission control parts defects for a engine is defective, the part will be repaired or replaced by Sears.
period of one year, subject to provisions set forth below. If any covered part on your
Owner’s Warranty Responsibilities
As the small off-road engine owner, you are responsible for the performance of the improper maintenance or unapproved modifications. You are responsible for presenting
required maintenance listed in your Operating and Maintenance Instructions. Sears your small off-road engine to an Authorized Sears Service Dealer as soon as a problem
recommends that you retain all your receipts covering maintenance on your small exists. The undisputed warranty repairs should be completed in a reasonable amount
off-road engine, but Sears cannot deny warranty solely for the lack of receipts or for of time, not to exceed 30 days. If you have any questions regarding your warranty rights
your failure to ensure the performance of all scheduled maintenance. As the small and responsibilities, you should contact a Sears Service Representative at 1-800-469-
off-road engine owner, you should however be aware that Sears may deny you warranty 4663. The emission warranty is a defects warranty. Defects are judged on normal engine
coverage if your small off-road engine or a part has failed due to abuse, neglect, performance. The warranty is not related to an in-use emission test.
Sears Emission Control Defects Warranty Provisions
The following are specific provisions relative to your Emission Control Defects Warranty 3. No Charge
Coverage. It is in addition to the Sears engine warranty for non-regulated engines found Repair or replacement of any Warranted Part will be performed at no charge to
in the Operating and Maintenance Instructions. the owner, including diagnostic labor which leads to the determination that a
1. Warranted Parts Warranted Part is defective, if the diagnostic work is performed at an Authorized
Coverage under this warranty extends only to the parts listed below (the Sears Service Dealer. For emissions warranty service contact your nearest
emission control systems parts) to the extent these parts were present on the Authorized Sears Service Dealer as listed in the “Yellow Pages” under “Engines,
engine purchased. Gasoline,” “Gasoline Engines,” “Lawn Mowers,” or similar category.
a. Fuel Metering System 4. Claims and Coverage Exclusions

• Cold start enrichment system Warranty claims shall be filed in accordance with the provisions of the Sears
• Carburetor and internal parts Engine Warranty Policy. Warranty coverage shall be excluded for failures of
• Fuel Pump Warranted Parts which are not original Sears parts or because of abuse, neglect
b. Air Induction System or improper maintenance as set forth in the Sears Engine Warranty Policy. Sears
• Air cleaner is not liable to cover failures of Warranted Parts caused by the use of add-on,
• Intake manifold non-original, or modified parts.
c. Ignition System 5. Maintenance
• Spark plug(s) Any Warranted Part which is not scheduled for replacement as required
• Magneto ignition system maintenance or which is scheduled only for regular inspection to the effect of
d. Catalyst System “repair or replace as necessary” shall be warranted as to defects for the warranty
• Catalytic converter period. Any Warranted Part which is scheduled for replacement as required
• Exhaust manifold maintenance shall be warranted as to defects only for the period of time up
• Air injection system or pulse valve to the first scheduled replacement for that part. Any replacement part that is
e. Miscellaneous Items Used in Above Systems equivalent in performance and durability may be used in the performance of
• Vacuum, temperature, position, time sensitive valves and switches any maintenance or repairs. The owner is responsible for the performance of
• Connectors and assemblies all required maintenance, as defined in the Sears Operating and Maintenance
2. Length of Coverage Instructions.
Sears warrants to the initial owner and each subsequent purchaser that the 6. Consequential Coverage
Warranted Parts shall be free from defects in materials and workmanship which Coverage hereunder shall extend to the failure of any engine components caused
caused the failure of the Warranted Parts for a period of one year from the date by the failure of any Warranted Part still under warranty.
the engine is delivered to a retail purchaser.
In the USA and Canada, a 24 hour hot line, 1-800-469-4663, has a menu of pre-recorded messages offering you engine maintenance information.
073808 Rev. A
32
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
MTD Consumer Group Inc, the United States Environmental Protection Agency (EPA), and for those products certified for sale in the state of
California, the California Air Resources Board (CARB) are pleased to explain the evaporative emission control system (ECS) warranty on your
2014-2015 small off-road equipment (outdoor equipment). In California, new outdoor equipment must be designed, built and equipped to
meet the State’s stringent anti-smog standards (in other states, outdoor equipment must be designed, built, and equipped to meet the U.S. EPA
small off-road spark ignition engine regulations). MTD Consumer Group Inc must warrant the ECS on your outdoor equipment for the period of
time listed below, provided there has been no abuse, neglect, or improper maintenance of the outdoor equipment.
Your ECS may include parts such as fuel tanks, fuel lines, fuel caps, valves, canisters, filters, vapor hoses, clamps, connectors, and other
associated emission-related components.
Where a warrantable condition exists, MTD Consumer Group Inc will repair your outdoor equipment at no cost to you including diagnosis,
parts, and labor.
MANUFACTURER’S WARRANTY COVERAGE:

This emission control system is warranted for two years. If any emission-related part on your outdoor equipment is defective, the part will be
repaired or replaced by MTD Consumer Group Inc.
OWNER’S WARRANTY RESPONSIBILITIES:

As the outdoor equipment owner, you are responsible for performance of the required maintenance listed in your owner’s manual. MTD
Consumer Group Inc recommends that you retain all receipts covering maintenance on your outdoor equipment, but MTD Consumer Group Inc
cannot deny warranty solely for the lack of receipts.
As the outdoor equipment owner, you should however be aware that MTD Consumer Group Inc may deny you warranty coverage if your
outdoor equipment or a part has failed due to abuse, neglect, improper maintenance, or unapproved modifications.
You are responsible for presenting your outdoor equipment to MTD Consumer Group Inc’s distribution center or service center as soon as
the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question
regarding your warranty coverage, you should contact the MTD Consumer Group Inc Service Department at 1-800-800-7310 or at
http://support.mtdproducts.com.
GENERAL EMISSIONS WARRANTY COVERAGE:

MTD Consumer Group Inc warrants to the ultimate purchaser and each subsequent purchaser that the outdoor equipment is: (1) designed,
built, and equipped so as to conform with all applicable regulations; and (2) free from defects in materials and workmanship that cause the
failure of a warranted part for a period of two years.
The warranty period begins on the date the outdoor equipment is delivered to an ultimate purchaser or first placed into service.
Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:
1. Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied is warranted for
the warranty period stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by MTD
Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the
remainder of the period.
2. Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period
stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.
3. Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the
period of time before the first scheduled replacement date for that part. If the part fails before the first scheduled replacement, the part
will be repaired or replaced by MTD Consumer Group Inc according to subsection (4) below. Any such part repaired or replaced under
warranty will be warranted for the remainder of the period prior to the first scheduled replacement point for the part.
4. Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge
to the owner.
5. Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to
service the subject engines or equipment.
6. The outdoor equipment owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective, emission-
related warranted part, provided that such diagnostic work is performed at a warranty station.
7. MTD Consumer Group Inc is liable for damages to other engine or equipment components proximately caused by a failure under
warranty of any warranted part.
8. Throughout the off-road engine and equipment warranty period stated above, MTD Consumer Group Inc will maintain a supply of
warranted parts sufficient to meet the expected demand for such parts.
9. Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to
the owner. Such use will not reduce the warranty obligations of MTD Consumer Group Inc.
10. Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or
modified parts by the ultimate purchaser will be grounds for disallowing a warranty claim. MTD Consumer Group Inc will not be liable to
warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
WARRANTED PARTS:
The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage
if MTD Consumer Group Inc demonstrates that the outdoor equipment has been abused, neglected, or improperly maintained, and that
such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part. That notwithstanding,
any adjustment of a component that has a factory installed, and properly operating, adjustment limiting device is still eligible for warranty
coverage. Further, the coverage under this warranty extends only to parts that were present on the off-road equipment purchased.
The following emission warranty parts are covered (if applicable):
1. Fuel Metering System
• Fuel pump
• Fuel tank
2. Evaporative Control
• Fuel hose
• Fuel hose clamps
• Tethered fuel cap
• Carbon canister
• Vapor lines
063015 Rev. B
REPAIR PROTECTION AGREEMENT
Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of
dependable operation. But like all products, it may require repair from time to time. That’s when having a Repair Protection
Agreement can save you money and aggravation.
Here’s what the Repair Protection Agreement* includes:
 Expert service by our 10,000 professional repair specialists
 Unlimited service and no charge for parts and labor on all covered repairs
 Product replacement up to $1500 if your covered product can’t be fixed
 Discount of 25% from regular price of service and related installed parts not covered by the agreement; also, 25% off
regular price of preventive maintenance check
 Fast help by phone – we call it Rapid Resolution – phone support from a Sears representative. Think of us as a “talking
owner’s manual.”
Once you purchase the Repair Protection Agreement, a simple phone call is all that it takes for you to schedule service. You
can call anytime day or night, or schedule a service appointment online.
The Repair Protection Agreement is a risk-free purchase. If you cancel for any reason during the product warranty period,
we will provide a full refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Repair
Protection Agreement today!
Some limitations and exclusions apply. For prices and additional information in the U.S.A. call 1-800-827-6655.
*Coverage in Canada varies on some items. For full details call Sears Canada at 1-800-361-6665.
Sears Installation Service
For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in
the U.S.A. or Canada call 1-800-4-MY-HOME®.
35

14A7A3ZW099

Uploaded by

Copyright:

Available Formats

14A7A3ZW099

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

14A7A3ZW099

Uploaded by

Copyright:

Available Formats

Operator’s Manual

Turn Tight® Extreme Rider

CAUTION For answers to your questions about

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

PRODUCT SPECIFICATIONS MODEL NUMBER

DO NOT MODIFY ENGINE SPARK ARRESTOR

SAVE THESE INSTRUCTIONS!

READ THE OPERATOR’S MANUAL(S)

DANGER— ROTATING BLADES

DANGER— ROTATING BLADES

WARNING— ROTATING BLADES

DANGER— ROTATING BLADES

DANGER — SAFETY DEVICES

WARNING— SLOPE OPERATION

WARNING— HOT SURFACE

DANGER — ROTATING BLADES

WARNING — FIRE HAZARD

WARNING — FIRE HAZARD

WARNING — FIRE HAZARD

Installing the Front Bumper

Fuel Tank Cap

Throttle/Choke Hour Meter

Forward Drive Pedal

Seat Adjustment Lever

Deck Lift Lever

6. The REVERSE CAUTION MODE will remain activated until:

a. The key is placed in either the NORMAL MOWING position or

Interval Item Service Service Log

WARNING Hydrostatic Neutral Adjustment

Insert Wrench Here

Flange Lock Nut

Off-Season Storage 9. Lubricate all lubrication points.

Problem Cause Remedy

a. Fuel Metering System 4. Claims and Coverage Exclusions

MANUFACTURER’S WARRANTY COVERAGE:

OWNER’S WARRANTY RESPONSIBILITIES:

GENERAL EMISSIONS WARRANTY COVERAGE:

You might also like