pmxteh .

Int_RadioRecInterferencePwr$|Int_RadioRecInterferencePucchPwr$
invrx(For inventry fiber loss)
get Router=LTE_CP_UP,Routetableipv4static=1,dst=1,nexthop=1 address > $trafficgw
(for getting traffic gateway baseband)

10.140.186.108
vlan 3653
mcc router=vr_OAM ping --count NTP system timming sync fault
(Reload cv with element manager )
get next hopaddress( to get IP address) inter-PIU Fault (due to 2nd duw
not installed or check F to F cable also sync cable if there is only one carrier
then delete second one)
get rilink (for link failure) PTP sync alarm (due to
transmission and also due to integrator)
get transport=1,ethernetpot=TN_A (FOR TNA PORT)
Ist sync(for sync) acl brmbackup=1 acc (restore)To clear Synchronization
alarm :2010-07-08 16:15:24 M Synch Reference Path HW Fault
clock_synchronisation_problem Synchronization=1
2010-07-08 16:51:07 M TimDevice_RadioClockIsNotStable loss_of_synchronisation
Subrack=1,Slot=1,PlugInUnit=1,Cbu=1,TimDeviceSet=1,TimDevice=1
2010-07-08 16:51:07 M Loss of Tracking replaceable_unit_problem Synchronization=1
>>> Total: 3 Alarms (0 Critical, 3 Major)
Use this:
get sync
acl sync
acc 10 resetLossOfTracking
y
Equipment=1,Subrack=1,Slot=1,PlugInUnit=1,Cbu=1,ExchangeTerminal=1,E1PhysPathTerm=p
p3
To Set Electrical Tilt (RET
1.pr retdevice
get proxy
set proxy electricaltilt value
get ret electrical
1.get IpSyncRef=1 ntpServerIpAddress
2.get IpSyncRef=1
3.get GigaBitEthernet=1
4.get IpInterface=1
5.lst sctp
6.pr rrus
7.pr RfBranch
8.pr AntennaUnitGroup
9.get SectorEquipmentFunction=S1
10.get RfBranch
11.get RbsConfiguration=1
12.get RfPort vswrSupervisionActive
13.get TermPointToMme=1 (Check details of MME Termination Point:)
14.get TermPointToMme ipAddress
15.get IpInterface defaultRouter (Get default router of IP Interface:)
16.acc RbsConfiguration=1 setUniqueLogicalName (Set Unique Logical Name of RBS:)
17.set RfPort=A vswrSupervisionActive True (Enable / Disable the status of
vswrSupervisionActive:)
18.set IpInterface=1 vid 110 (Change value of VID of an IP Interface:)
19.lset IpInterface=1 defaultRouter0 100.100.100.1 (Change Default Router IP of IP
Interface:)
20.acc IpHostLink=1 assignIpAddress (Change O&M IP Address:)
21.get Synchronization=1 (Check the property of ENodeB synchronization:)
22.cr IpSystem=1,IpAccessHostEt=1,IpSyncRef=1 (Process to create IpSyncRef:)
23.acc Synchronization=1 addSyncRefResource (Add Sync Reference Resource for ENodeB
Synchronization:)
24.acc Synchronization=1 removeSyncRefResource (100.) Process to remove Sync
Reference Resource from ENodeB synchronization:
25.del IpSyncRef=1 (Process to delete IpSyncRef=1)
26.cab (Check the board status:)
27.acc 0 manualrestart (Restart the RBS:)
28.to reset/add sync
get sync � to get syn ldn
acl sync � to get cmd on sync
acc 899 resetLossOfTracking � to reset sync
-
put ldn sync ref :-
Equipment=1,Subrack=1,Slot=1,PlugInUnit=1,Cbu=1,ExchangeTerminal=1,E1PhysPathTerm=p
p1
acc 899 addSyncRefResource
-
put ldn sync ref :-
Equipment=1,Subrack=1,Slot=1,PlugInUnit=1,Cbu=1,ExchangeTerminal=1,E1PhysPathTerm=p
p2

29.check radio
get radio
lst carrier , get fach,rach,pch
30.to check site
lst .354 � site id
ldeb .354 � to deblock all
bl .354 � to block all
lh ru fui get devstat � to check vswr - RBS 3116
lhsh 001200/port_1_dev_11 asc vswr - RBS 3206
kget . � tuk dpt kget file
31.To read MCPA temp
To check cell state
Cabx (to check RBS status)

lhsh 010200/port_0_dev_13 mcpaBoard temp

lhsh 010200/port_0_dev_13 help

lhsh 010200/port_0_dev_13 restart (if need to restart)

32.To set Electrical Tilt (RET)

pr retdevice

get <proxy>

set <proxy> electricalAntennaTilt <value>

get ret electrical

33.To check cell state
get radiolinks (to see how many line/s being used)
lst cell
34.To check RBS info
In RBS
??
Get 0
??
Get 1 (check ntpServerAddressPrimary)
35.To check network clock synchronisation
In RNC & RBS
??
Read clock (GMT +8)
??
ntpconfig info
??
Check which OMNIFSERVER the node is connected to (i.e ntpServerAddressPrimary) �
from get 1
36. to check interference
pmr
choose 1, restart java if rssi no value
pr java
acc pr restart
37.

1.get . linkrate
2.get .rfportref (for port )
3.get ipoam=1 ip=1
4.GTAC#L1
rbs

cabx

st carr

st ret

st sec

alt

lhru sfp 0 ___________(outdoor k SFP module check kerny k liye)

cpridump ___________(indoor k SFP module check kerny k liye)

get . sfp 0

hget . iuantennamodelnumber|electri|maxtilt|mintilt

h
get retdevice=1 userlabel|operationalstate|electricalantennatilt (ret label
check)

get . uniqueid

get . electricalantennatilt

get iphost
st gps

get ret cali (for ret calibration check)

lst near ( for ret related check the enabels or disables)

lst iub ( for site check lock or not lock on 3G )

get . radiobuildingblock (to check RBB in w900)

Get. radio noof (check traffic in 3G)
st rilink

log in nice format

1.lgevsm

Get 1 (check ,ntpserver address

to view delay and attenaution

Get jumper
get feeder
get rbs xdl

0534728003 14580692
60 Equipment=1,ExternalAntenna=1-1-
1,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1
61 Equipment=1,ExternalAntenna=1-1-
1,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 FOR Y3
64 Equipment=1,ExternalAntenna=1-1-
1,AuxPlugInUnit=2_LTE,RetuDeviceGroup=1,RetDeviceSet=1
65 Equipment=1,ExternalAntenna=1-1-
1,AuxPlugInUnit=2_LTE,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice FOR LTE 2300 FOR
Y4

74 Equipment=1,ExternalAntenna=1-1-
3,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1
75 Equipment=1,ExternalAntenna=1-1-
3,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 FOR u900 R1

398 Equipment=1,SectorAntenna=3-
1,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1
399 Equipment=1,SectorAntenna=3-
1,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 FOR 3G 2100 FOY Y1

To clear Synchronization alarm :2010-07-08 16:15:24 M Synch Reference Path HW Fault

clock_synchronisation_problem Synchronization=1
2010-07-08 16:51:07 M TimDevice_RadioClockIsNotStable loss_of_synchronisation
Subrack=1,Slot=1,PlugInUnit=1,Cbu=1,TimDeviceSet=1,TimDevice=1
2010-07-08 16:51:07 M Loss of Tracking replaceable_unit_problem Synchronization=1
>>> Total: 3 Alarms (0 Critical, 3 Major)
Use this:
get sync
acl sync
acc 10 resetLossOfTracking
y
Equipment=1,Subrack=1,Slot=1,PlugInUnit=1,Cbu=1,ExchangeTerminal=1,E1PhysPathTerm=p
p3