Cg-Prc002e-En 0712

Product Catalogue
CGAD Liquid Chillers

Air-Cooled
Scroll Compressor
20 to 150 Tons
Models: 50 / 60 Hz
CGAD020 CGAD040 CGAD070 CGAD100

July 2012 CG-PRC002E-EN

Introduction
CGAD
IMPORTANT:
Air-Cooled Liquid Chillers
Dimensional measuring units on this
Designed for great performance.
catalog are on milimitres (mm). (Exept
Built to last.
for those locally referencied).
For more than 40 years Trane has been
using the best resources available on
development engineering, production and
marketing to produce quality equipments.
All this tradition and know-how were
gathered to develop the new generation of
CGAD liquid chillers 20 to 150 Tons,
equipped with scroll compressors.
2 CG-PRC002E-EN
Contents
Introduction 2
Model Number 4
General Data 5
Selection Procedures 6
Application Considerations 7
Performance Adjustment Factors 9
Performance Data 12
Acustic Pressure Levels 16
Controls 17
Electrical Data 21
Dimensional Data 22
Mechanical Especifications 34
General Dimensions 36
Conversion Table 37
CG-PRC002E-EN 3
Model Number
C G A D 1 5 0 J B A 0 N 2 N N A N 0 N N N N N N N N 0 N P 0 0 0 N
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
Digits 1, 2 - Unit Model Digit 15 - Evaporator Application Digit 25 - Protection panels

CG = "Cold Generator" Scroll Chiller N = Standard Cooling (40-60°F) N = No Protection panels
Digit 3 - Unit Type Digit 16 - Coil Type Digit 26 - Installation accessories

A = Air Cooled A = Aluminium fins N = Without Installation accessories
S = Yellow Fin R = Neoprene Vibration isolators
Digit 4 - Model Series F = Adapter Kit for Flange
D = Sequence D Digit 17 - Piping Configuration G = Isolator and Flange adapter kit
N = Standard
Digits 5, 6 e 7 - Nominal Capacity A = Service valves on suction and discharge Digit 27 - Digit Reserved
020 = 20 Ton. lines 0 = Reserved
025 = 25 Ton.
030 = 30 Ton. Digit 18 - Digit Reserved Digit 28 - Digit Reserved
040 = 40 Ton. 0 = Reserved 0 = Reserved
050 = 50 Ton.
060 = 60 Ton. Digit 19 - Feed Type Digit 29 - Language - Literature/Labels
070 = 70 Ton. N = Terminal Block P = Portuguese/Spanish
080 = 80 Ton. D = Disconnector Key
090 = 90 Ton. C = Circuit Breaker Digit 30 - Digit Reserved
100 = 100 Ton. 0 = Reserved
120 = 120 Ton. Digit 20 - Remote Operation Interface
150 = 150 Ton. N = No Remote Interface Digit 31 - Digit Reserved
C = Tracer Comm3 Interface 0 = Reserved
Digit 8 - Unit Voltage L = Comm5 - LonTalk Compatible (LCI-C)
C = 220/60/3 Interface Digit 32 - Digit Reserved
J = 380/60/3 0 = Reserved
D = 380-400/50/3 Digit 21 - Input controls
4 = 440-460/60/3 N = No controls Digit 33 - Product Type
R = External Leaving Water Setpoint N = Standard
Digit 9 - Manufacturing Location Z = Special
B = Curitiba Plant - Brazil Digit 22 - Output controls
N = No controls
Digits 10,11 - Sequence of Modifi. minor of A = Alarm Relay Output
Project
A0 - Sequence A0 (Defined by factory) Digit 23 - Electrical Accessories
N = No acessories
Digit 12 - Certifying Agency
N = No certification Digit 24 - Control Panel Accessories
N = No acessories
Digit 13 - Refrigerant Type
2 = R22
4 = R407c
Digit 14 - Expansion Valve type

N = Thermostatic
The product's code describes the configuration, capacity, and optional characteristics. It is very important to
indicate the correct order of the equipment's code in order to avoid future problems when delivering them. Above
you will find the description of each digit that makes up the product code.
4 CG-PRC002E-EN
General
Data
Tab. 01 - General Data - CGAD 20-90 TR - 50 or 60 Hz

Mo del (1) CG AD 020 CGAD025 CG AD030 CG AD040 CGAD050 CGAD060 CGAD070 CG AD080 CG AD090 CGAD100 CG AD120 CGAD150
60 Hz
Capacity Tons 17,9 21,4 26,5 36,1 42, 8 52,6 65,7 76,2 82,6 95,3 116,8 144,0
(3) 20,0 27,2 30,7 41,3 53, 9 61,6 71,8 82,2 93,9 106,5 135,3 156,5
Sys tem KW
(2)
MC A A 54,0 68,0 78,0 97,0 123,0 142, 0 163,0 192, 0 210, 0 255,0 295,0 376,0
(3)
Efficiency E.E.R. 10,8 9,4 10,4 10,5 9,5 10,2 11,0 11,1 10,5 10,7 10,4 11, 0
KW /TR 1,115 1,273 1,157 1,143 1,258 1,171 1, 093 1,079 1,137 1,118 1,158 1,087
50 Hz
Capacity Tons 15,5 18,6 23,0 31,2 37, 2 45,5 56,5 65,4 71,2 85,2 104,7 128,6
(3) 16,8 23,0 25,8 34,6 45, 6 51,8 59,9 68,9 78,4 95,4 121,0 140,5
Sys tem KW
(4) A 45,0 57,0 65,0 80,0 110,0 116, 0 130,0 150, 0 170, 0 190,0 225,0 284,0
MC A
(3) E.E.R. 11,1 9,7 10,7 10,8 9,8 10,6 11,3 11,4 10,9 10,7 10,4 11, 0
Efficiency
KW /TR 1,086 1,238 1,123 1,109 1,227 1,137 1, 060 1,053 1,102 1,119 1,155 1,093
Comp ressor
(7)
Model SM125 SM185 SM125 SM185 SM125 SM185 SM125 SM185 SM185 SM125 SM185 SM125 SM185 SY300 SY240 SY300
Type Scroll Scroll Sc roll Sc roll Scroll Scroll Scroll Scrol l Scroll Scroll Sc roll Scroll
Quant ity 2 1 /1 2 4 2/2 4 2/4 4 /2 6 4 6 6
Nominal Capac ity Tons 10 15/10 15/ 15 10 15/10 15 15 / 10 15 / 10 15 25 20 25
Evap orator
Water Storage Liters 44 41 62 52 79 143 151 143 122 122 173 277
Mi n. water flow rate 3 5,5 6,8 8, 2 10,9 13, 6 16,4 21,8 27,3 27,3 32,7 40,9 49, 1
m /h
Max. water flow rate 3 16,4 20,4 24,5 32,7 40, 9 49,1 65,4 81,8 81,8 98,1 122,7 147,2
m /h
Inlet connec tion (8) 2" 2" 2 1/ 2" 2 1/ 2" 3" 4" 4" 4" 4" 4" 6" 6"
Outlet connect ion (8) 2" 2" 2 1/ 2" 2 1/ 2" 3" 4" 4" 4" 4" 4" 6" 6"
Condenser
Type Aluminum f ins , 3/8"- OD copper tubes
No. of coils 2 2 2 4 4 4 4 4 4 4 4 4
Total face area 2 4,7 4,7 4, 7 8, 5 11, 0 11,0 14,0 14,7 14,7 13,1 16,9 19, 5
m
Fins per inches 16 16 14 16 16 16 14 14 14 16 16 16
No. of rows 2 2 3 2 2 2 3 3 3 3 3 3
Fans
Quant ity 2 3 3 4 6 6 6 8 8 6 8 10
Diameter mm 762 762 762 762 762 762 762 762 762 762 762 762
3
Air f low rate m /h 32.620 45. 870 44.170 64.560 95.140 95.140 97.690 122.330 122.330 98. 118 130.824 163.530
RPM RPM 1140 1140 1140 1140 1140 1140 1140 1140 1140 1140 1140 1140
Motor power KW 1,12 1, 12 1,12 1,12 1,12 1,12 1,12 1, 12 1,12 1, 12 1, 12 1,12
Transmiss ion t ype Direct Direc t Direct Direct Direct D irect Direct Direc t Direc t Direc t Direc t Direct
General Data
Height mm 1840, 5 1840,5 1840,5 2190,5 2190,5 2190,5 2190,5 2190,5 2190,5 2376,0 2376,0 2376,0
(5)
Lengt h mm 2195, 0 2195,0 2195,0 2389,0 2989,0 2989,0 3695,0 3903,0 3903,0 3425,0 4949,0 4949,0
Width mm 1350, 0 1700,0 1700,0 1880,0 1880,0 1880,0 1880,0 1880,0 1880,0 2242,0 2242,0 2242,0
(6) 2 2,700 3,400 3,400 3,940 5,250 5,250 6, 580 6,970 6,970 7,237 10, 654 10,654
Foot print area m
Standard R-22 R-22 R-22 R-22 R-22 R -22 R-22 R-22 R-22 R-22 R -22 R-22
Ref rigerant t ype
Optional R-407C R-407C R-407C R-407C R -407C R-407C R-407C R-407C R-407C R-407C R-407C R-407C
No. of circuits 1 1 1 2 2 2 2 2 2 2 2 2
Capacity stages 50/100 40/ 100 50/100 25 / 50 20 / 40 25 / 50 29/57 31/63 33/67 25/50 17/33 17/33
75 / 100 70 / 100 75 / 100 79/100 81/ 100 83/100 75/ 100 67/ 100 67/100
Operating weight Kg 1340 1420 1480 1910 2210 2500 3000 3240 3220 3775 4135 4653
Shipping weight Kg 1300 1380 1420 1860 2130 2360 2850 3100 3100 3653 3962 4376
Notes:
(1) Rated in accordance with ARI Standard 550/590-03.
(2) MCA Ratings (Minimum Circuit Ampacity) based on 380V / 60Hz.
(3) Ratings based on global consumption (compressors and fans).
(4) MCA Ratings (Minimum Circuit Ampacity) based on 380V / 50Hz.
(5) Control panel width is included in the unit length
(6) Control panel area is not included.
(7) Compressor model refers to units with R22 (CGAD020-090). Models presented in this manual are up to the present time.
(8) The adapters to Victaulic connection are not supplied in the standard option.
(9) Operating Weight includes refrigerant and water weight.
(10) Shipping Weight includes only refrigerant weight.
CG-PRC002E-EN 5
Selection
Procedures
Liquid chiller capacity on table of Selection example: For example:

performance adjust factors, show the Corrected capacity = Capacity (not
most frequent leaving water temperatures. Data: adjusted) x Glycol Capacity Adjustment
The table reflects a temperature drop of 5,5 System load required= 70 Tons. Factor
ºC (10ºF) through the evaporator. For low Leaving chilled water temp. = 7ºC Corrected Flow = Flow (not adjusted) x
temperature selections, check the tables Chilled water temperature drop = 5,5ºC Glycol Flow Rate Adjustment Factor
for it. (10°F)
To select a CGAD Air-Cooled Liquid Chiller Project ambient temperature = 35ºC 5 The final unit selection is: CGAD 080B
Trane, the following information is Refrigerant Type: R-22
required: 1 Calculate the required chilled water flow Cooling capacity =76,2 Tons.
1 Thermal project load of project in tons of using the formula below: Entering temperatures = 12,5 °C
cooling. GPM = 70 Tons x 24 = 168 GPM Leaving chilled water temperature = 7ºC
2 Chilled water temperature project drop. 10ºF Chilled water flow =168 GPM
3Leaving chilled water project 2 Using table 03 (Performance Data - R- Evaporator pressure drop =2,74 m
temperature. 22), a CGAD 080 unit at these conditions Compressor consumption = 81,1 kW
4 Project ambient temperature and refrig- will output 76,2 Tons with a compressor
erant type. consumption of 81,1 kW.
The evaporator flow is determined through 3 Determine the evaporator pressure drop NOTE 2:
the following formulas: using the flow and the evaporator water Minimum leaving chilled water tempera-
pressure drop curves, introducing the ture setpoint
Tons X 24 curve at 168 GPM, the pressure drop for an
GPM =
Temperature drop (°F) evaporator with the nominal value of 80 The minimum leaving chilled water
Tons is 9 ft, or 2,74 m. temperature setpoint is 4ºC. For applica-
tions where a lower setpoint is required, a
kW (Capacity) X 0,239 4 For selection of low temperature units, or glycol solution must be used. Contact the
L/s = applications in which the altitude is
Temperature drop (°C) local Trane engineer for further
significantly above sea level, or the information.
temperature drop is different from 5,5 ºC,
NOTE 1: contact a local Trane engineer for further
The flow should be within the limits information.
specified in General Data table.
Note:
The selection above is an example for manual equipment selection. Please note that a more accurate data check is required for a correct selection.
6 CG-PRC002E-EN
Application
Considerations
Unit Sizing Warm air recirculation occurs when the to the condenser coil is restricted. Both
Unit capacities are listed in the airflow from the condenser fans warm air recirculation and coil starvation
Performance Data section. Intentionally discharged back at the condenser coil cause reductions in unit efficiency and
over-sizing a unit to assure adequate inlet, due to installation site restrictions. capacity, due to the associated high
capacity is not recommended. The excess Coil starvation occurs when the free airflow discharge pressures.
in the system and compressor capacity
calculation results in an over-sized liquid
chiller. In addition, an oversized unit is
usually more expensive to purchase,
A - Provide Vertical Clearance
install and operate. If over-sizing is
desired, consider using two units.
Unit Placement
1 Setting the Unit
2 Isolation and Sound Transmissions
The most effective isolation solution is to
locate the unit away from any sound
sensitive area. Structurally transmitted
sound can be reduced by vibration
eliminators. Spring isolators have proved
to be of little efficiency in CGAD Air-Cooled
Liquid Chiller installations and thus are
not recommended. An acoustical B - Provide Side Clearance
engineer should always be consulted on
applications with critical acoustic reduction
levels.
For maximum isolation, water lines and
electrical conduits should also be
isolated. Wall sleeves and rubber-isolated
piping hangers can be used to reduce the
sound transmitted through water piping.
To reduce the sound transmitted through
electrical conduits, use flexible electrical
conduits. State and local codes on sound
emissions should always be considered. C - Provide enough clearance between devices
As the environment in which a sound
source is located affects the sound
pressure, unit placement must be
carefully evaluated.
3 Unit Location
A General
Unobstructed airflow for the condenser is D - Installations in locations surrounded by walls
essential to assure efficient operation and
the liquid chiller capacity. When
determining unit placement, careful
considerations must be given to assure
enough air flow across the condenser
heat-transfer surface.
Two conditions should be avoided in order
to achieve optimum performance: warm
air recirculation and coil starvation.
CG-PRC002E-EN 7
Application
Considerations
Evaporator hydraulic piping components The manometer with connection should Flow-Switch
The figure below shows how to proceed be installed at water inlet and outlet Verify that safety interlockings, particularly
with the installation of the water piping. An according to item 9 in the figure below in the flow-switch, are installed in straight and
air purge is placed on the evaporator and order to avoid reading mistakes. horizontal runs, with vanes adequate to the
at the water outlet. Provide additional air Manometers and thermometers must be pipe diameter, and the distance from cur-
purges at high piping points to release it installed at the appropriate height to avoid ves and valves must be at least 5 times its
from the chilled water system. parallax errors*. Thermometers must be of diameter, on each side.
glass or mercury-scale type, with colored
Evaporator Drain contrasting fluid, and provide easy reading. Water treatment
The evaporator drain connection must be The use of untreated or improperly treated
piped to an available strainer in order to - Manometers must be equipped with water may result in scaling, erosion,
drain the evaporator even during siphons; corrosion, algae and slime. The services
operation. Install a gate valve in the drain - Install gate valves to isolate the of a qualified water treatment specialist
line. manometers when they are not being should be engaged to determine what
used. treatment, if any, is advisable. Trane do
Thermometers and Manometers Brasil assumes no responsibility for
It is essential to install thermometers Use piping joints to facilitate assembly equipment failures resulting from the use
(items 5 and 12 in the figure) and and disassembly services. of untreated or improperly treated water.
manometers (item 9) at the chilled water Inlet and outlet must be equipped with
inlet and outlet. These instruments must gate valves to isolate the evaporator during
be installed close to the unit, with a service, and a globe valve must be
maximum scale of 1°C for thermometers installed at the outlet to adjust the water
and 0,1 kgf/cm2 for manometers. flow.
Important: In order to avoid evaporator
damages, do not exceed a 150-psig
water pressure.
Fig. 01 - Evaporator hydraulic piping components
* Parallax error: Apparent displacement of an object, when the observation point changes. It is especially said of the apparent deviation of a measure instrument needle, when it is
not observed from a vertical point of view (parallax error).
8 CG-PRC002E-EN
Performance
Adjustment Factors
Fig. 02 - Evaporator Pressure Drop - 20 to 60 Tons Units
Load loss (Ft. of water)
Unit Conversion
From: To: Multiplier:
Gallons/min (GPM) L/s 0,06308

Feet of water (Ft Water) Pa 2990
Evaporator Water Flow (GPM)

Evaporator Water Flow ( L/s )
Load loss (Ft. of water)
Load loss (kPa)
Evaporator Water Flow (GPM)
CG-PRC002E-EN 9
Performance
Adjustment Factors
Conversão de Unidades
De: Para: Multiplicador:
Galões/min (GPM) L/s 0,06308

Pés de Água (Ft Água) Pa 2990
Fig. 05 - Evaporator Pressure Drop - 150 Tons Units
10 CG-PRC002E-EN
Performance
Adjustment Factors
Fig. 06 - Ethylene Glycol Performance Factors Fig. 07 - Propylene Glycol Performance Factors
Flow GPM Flow GPM

Capacity Capacity
Compressor Power Compressor Power
Adjustment Factor
Adjustment Factor
% of Ethylene Glycol in Weight % de Propylene Glycol in Weight
Tab. 02 - Altitude Correction Factors Fig. 08 - Ethylene and Propylene Freezing Points
Ethylene Glycol
Propylene Glycol
Altitude Capacity Consum ption Water Flow

0 1,000 1,000 1,000
500 0,997 1,012 0,997
1000 0,994 1,024 0,994
1500 0,991 1,037 0,991
2000 0,987 1,052 0,987
Temperature °F
Temperature°C
2500 0,983 1,067 0,983

3000 0,978 1,084 0,978
% of Antifreezing in Weight
CG-PRC002E-EN 11
Performance
Data 60 HZ
Tab. 03a -Performance Data - R- 22 (TSA = 4ºC) Tab. 03e -Performance Data - R- 22 (TSA = 8ºC)
Water Leaving Water Leaving
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
Temperature = 4ºC Temperature = 8ºC
Capacity(Tons) 17,5 22,1 25,5 35,3 44,1 50,7 63,7 72,6 79,5 91,6 112,4 138,6 Capacity(Tons) 19,5 24,8 28,7 39,4 49,7 56,9 71,6 81,9 89,5 103,2 126,7 155,8
Condenser entering Air Temperature (ºC)
30 (kW) 16,8 21,7 25,8 34,9 42,9 51,7 63,5 71,8 79,7 95,4 120,6 141,0 30 (kW) 17,3 22,4 26,7 36,0 44,2 53,4 65,9 74,6 82,6 99,7 126,1 147,2
Temp. de entrada ar condensador (ºC)

Flow (m³/h) 9,5 12,0 13,9 19,2 24,1 27,6 34,7 39,6 43,4 50,0 61,0 76,0 Flow (m³/h) 10,6 13,5 15,6 21,5 27,1 31,0 39,0 44,6 48,8 56,0 69,0 85,0
35 (kW) 18,8 24,0 28,3 38,9 47,4 56,8 70,2 78,9 87,5 103,5 131,5 152,2 35 (kW) 19,3 24,8 29,3 40,1 48,8 58,7 72,7 81,8 90,6 108,0 137,3 158,7
Flow (m³/h) 9,1 11,5 13,3 18,4 23,1 26,5 33,3 37,9 41,5 48,0 59,0 72,0 Flow (m³/h) 10,2 13,0 15,0 20,6 26,0 29,8 37,4 42,8 46,7 54,0 66,0 82,0
40 (kW) 20,9 26,6 31,2 43,4 52,5 62,6 77,7 86,8 96,2 112,5 143,8 164,9 40 (kW) 21,4 27,4 32,2 44,6 54,0 64,6 80,3 89,9 99,6 117,4 149,9 171,8
Flow (m³/h) 8,7 11,0 12,7 17,6 22,0 25,2 31,7 36,2 39,6 46,0 56,0 69,0 Flow (m³/h) 9,7 12,4 14,3 19,7 24,8 28,4 35,7 40,9 44,6 52,0 63,0 78,0
45 (kW) 23,3 29,4 34,3 48,4 58,1 69,0 85,9 95,6 105,8 123,7 159,2 180,7 45 (kW) 23,9 30,3 35,4 49,6 59,7 71,1 88,7 98,8 109,3 129,2 165,5 188,3
Flow (m³/h) 8,2 10,4 12,1 16,7 20,9 23,9 30,1 34,3 37,6 43,0 53,0 66,0 Flow (m³/h) 9,3 11,7 13,6 18,7 23,6 27,0 34,0 38,8 42,4 49,0 60,0 74,0
Tab. 03b -Performance Data - R- 22 (TSA = 5ºC) Tab. 03f -Performance Data - R- 22 (TSA = 9ºC)
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
30 (kW) 16,9 21,9 26,0 35,2 43,2 52,1 64,1 72,5 80,4 96,4 121,9 142,5 30 (kW) 17,4 22,6 26,9 36,2 44,5 53,8 66,5 75,3 83,4 100,8 126,1 148,8
Flow (m³/h) 9,8 12,4 14,3 19,8 24,8 28,5 35,8 40,8 44,7 52,0 63,0 78,0 Flow (m³/h) 10,9 13,9 16,1 22,1 27,8 31,9 40,1 45,9 50,2 58,0 69,0 88,0
35 (kW) 18,9 24,2 28,6 39,2 47,8 57,3 70,9 79,6 88,3 104,6 132,9 153,8 35 (kW) 19,4 25,0 29,5 40,3 49,2 59,2 73,4 82,6 91,5 109,2 137,3 160,4
Flow (m³/h) 9,4 11,9 13,7 19,0 23,8 27,3 34,3 39,1 42,8 49,0 61,0 75,0 Flow (m³/h) 10,5 13,4 15,4 21,2 26,7 30,6 38,5 44,1 48,1 56,0 66,0 84,0
40 (kW) 21,1 26,8 31,4 43,7 52,9 63,1 78,3 87,6 97,0 113,7 145,3 166,6 40 (kW) 21,6 27,6 32,5 44,9 54,4 65,1 81,0 90,7 100,4 118,7 149,9 173,6
Flow (m³/h) 9,0 11,3 13,1 18,1 22,7 26,0 32,7 37,3 40,8 47,0 58,0 71,0 Flow (m³/h) 10,0 12,7 14,7 20,3 25,6 29,2 36,8 42,1 45,9 53,0 63,0 80,0
45 (kW) 23,5 29,6 34,6 48,7 58,5 69,5 86,6 96,4 106,7 125,1 160,7 68,0 45 (kW) 24,0 30,5 35,7 49,9 60,2 71,6 89,4 99,6 110,3 130,6 165,5 190,3
Flow (m³/h) 8,5 10,7 12,4 17,2 21,6 24,7 31,0 35,5 38,7 45,0 54,0 182,6 Flow (m³/h) 9,5 12,1 14,0 19,3 24,3 27,7 35,0 40,0 43,6 50,0 60,0 76,0
Tab. 03c -Performance Data - R- 22 (TSA = 6ºC) Tab. 03g -Performance Data - R- 22 (TSA = 10ºC)
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
30 (kW) 17,1 22,1 26,2 35,4 43,5 52,5 67,7 73,2 81,1 97,5 123,3 144,0 30 (kW) 17,5 22,8 27,1 36,5 44,8 54,3 67,1 76,0 84,2 101,9 129,0 150,4
Flow (m³/h) 10,1 12,8 14,8 20,4 25,5 29,3 36,8 42,1 46,0 53,0 65,0 80,0 Flow (m³/h) 11,2 14,3 16,6 22,7 28,6 32,8 41,3 47,3 51,6 60,0 73,0 90,0
35 (kW) 19,0 24,4 28,8 39,5 48,1 57,8 71,5 80,4 89,0 105,7 134,4 155,4 35 (kW) 19,5 25,2 29,8 40,6 49,6 59,7 74,0 83,4 92,3 110,4 140,3 162,1
Flow (m³/h) 9,7 12,2 14,1 19,5 24,5 28,1 35,3 40,3 44,1 51,0 62,0 77,0 Flow (m³/h) 10,8 13,7 15,9 21,8 27,5 31,5 39,6 45,4 49,7 57,0 70,0 86,0
40 (kW) 21,2 27,0 31,7 44,0 53,3 63,6 79,0 88,4 97,9 115,0 146,8 168,3 40 (kW) 21,7 27,8 32,7 45,2 54,8 65,6 81,7 91,5 101,3 120,0 153,1 175,4
Flow (m³/h) 9,2 11,7 13,5 18,6 23,4 26,8 33,7 38,5 42,1 49,0 59,0 74,0 Flow (m³/h) 10,3 13,1 15,2 20,8 26,3 30,0 37,8 43,3 47,2 55,0 67,0 83,0
45 (kW) 23,6 29,8 34,9 49,0 58,9 70,0 87,3 97,2 107,6 126,4 162,3 184,5 45 (kW) 24,1 30,7 36,0 50,3 60,6 72,2 90,1 100,5 111,2 132,0 168,9 192,2
Flow (m³/h) 8,7 11,1 12,8 17,7 22,2 25,4 32,0 36,5 40,0 46,0 56,0 70,0 Flow (m³/h) 9,8 12,4 14,4 19,8 25,0 28,5 36,0 41,2 44,9 52,0 63,0 79,0
Tab. 03d -Performance Data - R- 22 (TSA = 7ºC)

Water Leaving
020
025
030
040
050
060
070
080
090
100
120
150
Temperature = 7ºC
Capacity(Tons) 19,0 24,1 27,9 38,4 48,2 55,3 69,6 79,5 86,9 100,2 123,0 151,5
30 (kW) 17,2 22,2 26,4 35,7 43,8 53,0 65,3 73,9 81,9 98,6 124,7 145,6
Flow (m³/h) 10,4 13,2 15,2 20,9 26,3 30,2 37,9 43,3 47,4 55,0 67,0 83,0
Capacity(Tons) 18,2 23,1 26,7 36,8 46,3 53,0 66,7 76,2 83,3 95,9 117,7 145,2
35 (kW) 19,1 24,6 29,1 39,8 48,5 58,2 72,1 81,1 89,8 106,9 135,8 157,1
Flow (m³/h) 9,9 12,6 14,6 20,1 25,2 28,9 36,4 41,6 45,4 52,0 64,0 79,0
Capacity(Tons) 17,4 22,1 25,5 35,2 44,2 50,6 63,7 72,8 79,5 91,6 112,4 138,9
40 (kW) 21,3 27,2 32,0 44,3 53,6 64,1 79,7 89,1 98,7 116,2 148,3 170,1 Notes:
Flow (m³/h) 9,5 12,0 13,9 19,2 24,1 27,6 34,7 39,7 43,3 50,0 61,0 76,0 (1) The values shown are in accordance with the operating conditions for the
Capacity(Tons) 16,5 20,9 24,3 33,4 42,0 48,0 60,5 69,1 75,5 87,0 105,8 131,9 ARI-590-92.
45 (kW) 23,7 30,1 35,2 49,3 59,3 70,6 88,0 98,0 108,5 127,8 163,9 186,4 (2) The Consumption (KW) column is the nominal consumption of the
Flow (m³/h) 9,0 11,4 13,2 18,2 22,9 26,2 33,0 37,7 41,2 47,0 58,0 72,0 compressors in that condition.
12 CG-PRC002E-EN
Performance
Data 60 HZ
Tab. 04a - Performance Data - R- 407C (TSA = 4ºC) Tab. 04e - Performance Data - R- 407C (TSA = 8ºC)
Water Leaving
Water Leaving
020
025
030
040
050
060
070
080
090
100
120
150
Temperature = 4ºC
020
025
030
040
050
060
070
080
090
100
120
150
Temperature = 8ºC
Capacity(Tons) 16,9 21,3 24,6 34,0 42,6 48,9 61,4 70,1 76,7 88,3 109,5 133,6
Capacity(Tons) 18,8 24,0 27,7 38,0 47,9 54,9 69,1 79,0 86,3 100,2 123,7 151,5
30 (kW) 17,4 22,5 26,7 36,1 44,4 53,5 65,7 74,3 82,5 93,2 116,1 137,4

30 (kW) 17,9 23,2 27,6 37,3 45,7 55,3 68,2 77,2 85,5 97,9 121,8 144,0
Flow (m³/h) 9,5 12,0 13,9 19,2 24,1 27,6 34,7 39,6 43,4 48,0 60,0 73,0
Flow (m³/h) 10,6 13,5 15,6 21,5 27,1 31,0 39,0 44,6 48,8 55,0 68,0 83,0
Capacity(Tons) 16,2 20,4 23,6 32,6 40,8 46,9 58,9 67,1 73,5 83,7 103,5 126,7
Capacity(Tons) 18,1 23,0 26,6 36,5 46,0 52,7 66,3 75,8 82,8 94,9 117,4 143,8
35 (kW) 19,5 24,8 29,3 40,3 49,1 58,8 72,7 81,7 90,6 102,4 128,5 150,2 35 (kW) 20,0 25,7 30,3 41,5 50,5 60,8 75,2 84,7 93,8 107,2 134,6 157,1
Flow (m³/h) 9,1 11,5 13,3 18,4 23,1 26,5 33,3 37,9 41,5 46,0 57,0 69,0
Flow (m³/h) 10,2 13,0 15,0 20,6 26,0 29,8 37,4 42,8 46,7 52,0 64,0 79,0
Capacity(Tons) 16,5 20,9 24,1 33,4 41,8 47,9 60,2 68,7 75,2 78,7 97,6 119,4
Capacity(Tons) 18,5 23,5 27,2 37,5 47,1 53,9 67,9 77,6 84,7 89,3 110,8 135,9
40 (kW) 21,6 27,5 32,3 44,9 54,3 64,8 80,4 89,8 99,6 112,6 142,9 164,6 40 (kW) 22,1 28,4 33,3 46,2 55,9 66,9 83,1 93,0 103,1 117,5 149,2 171,6
Flow (m³/h) 8,7 11,0 12,7 17,6 22,0 25,2 31,7 36,2 39,6 43,0 53,0 65,0
Flow (m³/h) 9,7 12,4 14,3 19,7 24,8 28,4 35,7 40,9 44,6 49,0 60,0 74,0
Capacity(Tons) 14,6 18,5 21,4 29,5 37,0 42,4 53,3 60,8 66,5 72,8 90,3 110,8
Capacity(Tons) 16,4 20,8 24,1 33,2 41,8 47,7 60,1 68,7 75,0 82,7 102,8 126,3
45 (kW) 24,1 30,4 35,5 50,1 60,1 71,4 88,9 98,9 109,5 125,1 161,2 182,5 45 (kW) 24,7 31,4 36,6 51,3 61,8 73,6 91,8 102,3 113,1 129,8 167,5 189,2
Flow (m³/h) 8,2 10,4 12,1 16,7 20,9 23,9 30,1 34,3 37,6 40,0 49,0 60,0
Flow (m³/h) 9,3 11,7 13,6 18,7 23,6 27,0 34,0 38,8 42,4 45,0 56,0 69,0
Tab. 04b - Performance Data - R- 407C (TSA = 5ºC) Tab. 04f - Performance Data - R- 407C (TSA = 9ºC)
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
30 (kW) 17,5 22,7 26,9 36,4 44,7 53,9 66,3 75,0 83,2 94,4 117,5 138,9 30 (kW) 18,0 23,4 27,8 37,5 46,1 55,7 68,8 77,9 86,3 97,9 123,3 145,8
Flow (m³/h) 9,8 12,4 14,3 19,8 24,8 28,5 35,8 40,8 44,7 50,0 62,0 75,0 Flow (m³/h) 10,9 13,9 16,1 22,1 27,8 31,9 40,1 45,9 50,2 55,0 70,0 85,0
35 (kW) 19,6 25,0 29,6 40,6 49,5 59,3 73,4 82,4 91,4 103,6 130,0 151,9 35 (kW) 20,1 25,9 30,5 41,7 50,9 61,3 76,0 85,5 94,7 107,2 136,2 158,9
Flow (m³/h) 9,4 11,9 13,7 19,0 23,8 27,3 34,3 39,1 42,8 47,0 58,0 71,0 Flow (m³/h) 10,5 13,4 15,4 21,2 26,7 30,6 38,5 44,1 48,1 52,0 66,0 81,0
40 (kW) 21,8 27,7 32,5 45,2 54,8 65,3 81,0 90,7 100,4 113,8 144,4 166,3 40 (kW) 22,4 28,6 33,6 46,5 56,3 67,4 83,8 93,9 103,9 117,5 150,9 173,4
Flow (m³/h) 9,0 11,3 13,1 18,1 22,7 26,0 32,7 37,3 40,8 44,0 55,0 67,0 Flow (m³/h) 10,0 12,7 14,7 20,3 25,6 29,2 36,8 42,1 45,9 49,0 62,0 76,0
45 (kW) 24,3 30,6 35,8 50,4 60,5 71,9 89,6 99,8 110,4 126,2 162,7 184,1 45 (kW) 24,8 31,6 36,9 51,6 62,3 74,1 92,5 103,1 114,2 129,8 169,2 191,0
Flow (m³/h) 8,5 10,7 12,4 17,2 21,6 24,7 31,0 35,5 38,7 41,0 51,0 63,0 Flow (m³/h) 9,5 12,1 14,0 19,3 24,3 27,7 35,0 40,0 43,6 45,0 58,0 71,0
Tab. 04c - Performance Data - R- 407C (TSA = 6ºC) Tab. 04g - Performance Data - R- 407C (TSA = 10ºC)
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
30 (kW) 17,7 22,9 27,1 36,6 45,0 54,3 70,1 75,8 83,9 95,5 118,8 140,6 30 (kW) 18,1 23,6 28,0 37,8 46,4 56,2 69,4 78,7 87,1 100,3 124,9 147,6
Flow (m³/h) 10,1 12,8 14,8 20,4 25,5 29,3 36,8 42,1 46,0 51,0 64,0 78,0 Flow (m³/h) 11,2 14,3 16,6 22,7 28,6 32,8 41,3 47,3 51,6 58,0 72,0 88,0
35 (kW) 19,7 25,3 29,8 40,9 49,8 59,8 74,0 83,2 92,1 104,8 131,5 153,6 35 (kW) 20,2 26,1 30,8 42,0 51,3 61,8 76,6 86,3 95,5 109,8 137,9 160,8
Flow (m³/h) 9,7 12,2 14,1 19,5 24,5 28,1 35,3 40,3 44,1 49,0 60,0 74,0 Flow (m³/h) 10,8 13,7 15,9 21,8 27,5 31,5 39,6 45,4 49,7 55,0 68,0 83,0
40 (kW) 21,9 27,9 32,8 45,5 55,2 65,8 81,8 91,5 101,3 115,0 146,0 168,0 40 (kW) 22,5 28,8 33,8 46,8 56,7 67,9 84,6 94,7 104,8 120,0 152,6 175,3
Flow (m³/h) 9,2 11,7 13,5 18,6 23,4 26,8 33,7 38,5 42,1 46,0 57,0 70,0 Flow (m³/h) 10,3 13,1 15,2 20,8 26,3 30,0 37,8 43,3 47,2 52,0 64,0 79,0
45 (kW) 24,4 30,8 36,1 50,7 61,0 72,5 90,4 100,6 111,4 127,4 164,3 185,8 45 (kW) 24,9 31,8 37,3 52,1 62,7 74,7 93,3 104,0 115,1 132,3 170,9 192,8
Flow (m³/h) 8,7 11,1 12,8 17,7 22,2 25,4 32,0 36,5 40,0 42,0 53,0 65,0 Flow (m³/h) 9,8 12,4 14,4 19,8 25,0 28,5 36,0 41,2 44,9 48,0 60,0 73,0
Tab. 04d - Performance Data - R- 407C (TSA = 7ºC)

Water Leaving
020
025
030
040
050
060
070
080
090
100
120
150
Temperature = 7ºC
Capacity(Tons) 18,3 23,3 26,9 37,0 46,6 53,4 67,1 76,7 83,9 97,2 120,0 147,2
30 (kW) 17,8 23,0 27,3 36,9 45,3 54,9 67,6 76,5 84,8 96,7 120,3 142,3
Flow (m³/h) 10,4 13,2 15,2 20,9 26,3 30,2 37,9 43,3 47,4 53,0 66,0 80,0
Capacity(Tons) 17,6 22,3 25,8 35,6 44,7 51,2 64,4 73,6 80,4 91,9 113,8 139,6
35 (kW) 19,8 25,5 30,1 41,2 50,2 60,2 74,6 83,9 92,9 106,0 133,0 155,3
Flow (m³/h) 9,9 12,6 14,6 20,1 25,2 28,9 36,4 41,6 45,4 50,0 62,0 76,0
Capacity(Tons) 18,0 22,8 26,4 36,4 45,8 52,4 65,9 75,3 82,3 86,6 107,7 131,6
40 (kW) 22,0 28,2 33,1 45,9 55,5 66,3 82,5 92,2 102,2 116,2 147,6 169,8
Flow (m³/h) 9,5 12,0 13,9 19,2 24,1 27,6 34,7 39,7 43,3 47,0 59,0 72,0
Notes:
Capacity(Tons) 15,9 20,2 23,4 32,2 40,6 46,4 58,4 66,7 72,9 80,0 99,5 122,4 (1) These values comply with operation conditions from ARI-590-92.
45 (kW) 24,5 31,2 36,4 51,0 61,4 73,1 91,1 101,4 112,3 128,6 165,9 187,5 (2) The column Consumption (kW) represents the nominal compressor
Flow (m³/h) 9,0 11,4 13,2 18,2 22,9 26,2 33,0 37,7 41,2 44,0 54,0 67,0 consumption in that condition.
CG-PRC002E-EN 13
Performance
Data 50 HZ
Tab. 05a -Performance Data - R- 22 (TSA = 4ºC) Tab. 05e -Performance Data - R- 22 (TSA = 8ºC)
Water Leaving Water Leaving Temperature
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
Temperature = 4ºC = 8ºC
30 (kW) 14,8 19,1 22,7 30,7 37,8 45,5 55,9 63,2 70,1 84,0 106,1 124,1 30 (kW) 15,2 19,7 23,5 31,7 38,9 47,0 58,0 65,6 72,7 87,7 111,0 129,5

Flow (m³/h) 8,4 10,6 12,3 16,9 21,2 24,3 30,5 34,8 38,2 44,0 53,7 66,9 Flow (m³/h) 9,4 11,9 13,8 18,9 23,8 27,3 34,3 39,3 42,9 49,3 60,7 74,8
35 (kW) 16,5 21,1 24,9 34,2 41,7 50,0 61,8 69,4 77,0 91,1 115,7 133,9 35 (kW) 17,0 21,8 25,8 35,3 42,9 51,7 64,0 72,0 79,7 95,0 120,8 139,7
Flow (m³/h) 8,0 10,2 11,7 16,2 20,3 23,3 29,3 33,4 36,5 42,2 51,9 63,4 Flow (m³/h) 9,0 11,4 13,2 18,2 22,9 26,2 32,9 37,7 41,1 47,5 58,1 72,2
40 (kW) 18,4 23,4 27,5 38,2 46,2 55,1 68,4 76,4 84,7 99,0 126,5 145,1 40 (kW) 18,8 24,1 28,3 39,2 47,5 56,8 70,7 79,1 87,6 103,3 131,9 151,2
Flow (m³/h) 7,7 9,7 11,2 15,5 19,4 22,2 27,9 31,8 34,8 40,5 49,3 60,7 Flow (m³/h) 8,6 10,9 12,6 17,4 21,8 25,0 31,5 36,0 39,3 45,8 55,4 68,6
45 (kW) 20,5 25,9 30,2 42,6 51,1 60,7 75,6 84,1 93,1 108,9 140,1 159,0 45 (kW) 21,0 26,7 31,2 43,6 52,5 62,6 78,1 86,9 96,2 113,7 145,6 165,7
Flow (m³/h) 7,3 9,2 10,6 14,7 18,4 21,1 26,5 30,2 33,1 37,8 46,6 58,1 Flow (m³/h) 8,2 10,3 12,0 16,5 20,8 23,7 29,9 34,2 37,3 43,1 52,8 65,1
Tab. 05b -Performance Data - R- 22 (TSA = 5ºC) Tab. 05f -Performance Data - R- 22 (TSA = 9ºC)
020
025
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
30
30 (kW) 14,9 19,3 22,9 31,0 38,0 45,8 56,4 63,8 70,8 84,8 107,3 125,4 30 (kW) 15,3 19,9 23,7 31,9 39,2 47,3 58,5 66,3 73,4 88,7 111,0 130,9
Flow (m³/h) 8,6 10,9 12,6 17,4 21,8 25,0 31,5 35,9 39,3 45,8 55,4 68,6 Flow (m³/h) 9,6 12,3 14,2 19,4 24,5 28,1 35,3 40,4 44,2 51,0 60,7 77,4
35 (kW) 16,6 21,3 25,2 34,5 42,1 50,4 62,4 70,0 77,7 92,0 117,0 135,3 35 (kW) 17,1 22,0 26,0 35,5 43,3 52,1 64,6 72,7 80,5 96,1 120,8 141,2
Flow (m³/h) 8,3 10,5 12,1 16,7 20,9 24,0 30,2 34,4 37,7 43,1 53,7 66,0 Flow (m³/h) 9,2 11,8 13,6 18,7 23,5 26,9 33,9 38,8 42,3 49,3 58,1 73,9
40 (kW) 18,6 23,6 27,6 38,5 46,6 55,5 68,9 77,1 85,4 100,1 127,9 146,6 40 (kW) 19,0 24,3 28,6 39,5 47,9 57,3 71,3 79,8 88,4 104,5 131,9 152,8
Flow (m³/h) 7,9 10,0 11,5 15,9 20,0 22,9 28,8 32,8 35,9 41,4 51,0 62,5 Flow (m³/h) 8,8 11,2 13,0 17,8 22,5 25,7 32,4 37,0 40,4 46,6 55,4 70,4
45 (kW) 20,7 26,0 30,4 42,9 51,5 61,2 76,2 84,8 93,9 110,1 141,4 59,8 45 (kW) 21,1 26,8 31,4 43,9 53,0 63,0 78,7 87,6 97,1 114,9 145,6 167,5
Flow (m³/h) 7,5 9,5 11,0 15,1 19,0 21,7 27,3 31,2 34,1 39,6 47,5 160,7 Flow (m³/h) 8,4 10,7 12,3 17,0 21,4 24,4 30,8 35,2 38,4 44,0 52,8 66,9
Tab. 05c -Performance Data - R- 22 (TSA = 6ºC) Tab. 05g -Performance Data - R- 22 (TSA = 10ºC)
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
30 (kW) 14,9 19,3 22,9 31,0 38,0 45,8 56,4 63,8 70,8 84,8 107,3 125,4 30 (kW) 15,4 20,1 23,8 32,1 39,4 47,8 59,0 66,9 74,1 89,7 113,5 132,4
Flow (m³/h) 8,6 10,9 12,6 17,4 21,8 25,0 31,5 35,9 39,3 45,8 55,4 68,6 Flow (m³/h) 9,9 12,6 14,6 19,9 25,2 28,9 36,3 41,6 45,4 52,8 64,2 79,2
35 (kW) 16,6 21,3 25,2 34,5 42,1 50,4 62,4 70,0 77,7 92,0 117,0 135,3 35 (kW) 17,2 22,2 26,2 35,7 43,6 52,5 65,1 73,4 81,2 97,2 123,5 142,6
Flow (m³/h) 8,3 10,5 12,1 16,7 20,9 24,0 30,2 34,4 37,7 43,1 53,7 66,0 Flow (m³/h) 9,5 12,1 14,0 19,2 24,2 27,7 34,9 39,9 43,7 50,2 61,6 75,7
40 (kW) 18,6 23,6 27,6 38,5 46,6 55,5 68,9 77,1 85,4 100,1 127,9 146,6 40 (kW) 19,1 24,5 28,8 39,8 48,2 57,7 71,9 80,5 89,1 105,6 134,7 154,4
Flow (m³/h) 7,9 10,0 11,5 15,9 20,0 22,9 28,8 32,8 35,9 41,4 51,0 62,5 Flow (m³/h) 9,1 11,5 13,4 18,3 23,1 26,4 33,3 38,1 41,6 48,4 59,0 73,0
45 (kW) 20,7 26,0 30,4 42,9 51,5 61,2 76,2 84,8 93,9 110,1 141,4 59,8 45 (kW) 21,2 27,0 31,7 44,3 53,3 63,5 79,3 88,4 97,9 116,2 148,6 169,1
Flow (m³/h) 7,5 9,5 11,0 15,1 19,0 21,7 27,3 31,2 34,1 39,6 47,5 160,7 Flow (m³/h) 8,6 11,0 12,7 17,4 22,0 25,1 31,7 36,2 39,5 45,8 55,4 69,5
Tab. 05d -Performance Data - R- 22 (TSA = 7ºC)

Water Leaving
020
025
030
040
050
060
070
080
090
100
120
Temperature = 7ºC
Capacity(Tons) 16,7 21,2 24,6 33,8 42,5 48,7 61,2 70,0 76,5 88,2 108,2
30 (kW) 15,1 19,5 23,2 31,4 38,5 46,6 57,5 65,0 72,1 86,8 109,7
Flow (m³/h) 9,1 11,6 13,4 18,4 23,1 26,5 33,4 38,1 41,7 48,4 59,0
Capacity(Tons) 16,0 20,3 23,5 32,4 40,7 46,7 58,7 67,1 73,3 84,4 103,6
35 (kW) 16,8 21,6 25,6 35,0 42,7 51,2 63,4 71,4 79,0 94,1 119,5
Flow (m³/h) 8,7 11,1 12,8 17,7 22,2 25,4 32,0 36,6 40,0 45,8 56,3
Capacity(Tons) 15,3 19,4 22,5 31,0 38,9 44,5 56,0 64,0 70,0 80,6 98,9
40 (kW) 18,7 23,9 28,2 39,0 47,2 56,4 70,1 78,4 86,9 102,3 130,5
Notes:
Flow (m³/h) 8,4 10,6 12,3 16,9 21,2 24,3 30,5 34,9 38,1 44,0 53,7
(1) These values comply with operation conditions from ARI-590-92.
Capacity(Tons) 14,5 18,4 21,3 29,4 37,0 42,3 53,2 60,8 66,4 76,5 93,1
45 (kW)
(2) The column Consumption (kW) represents the nominal compressor
20,9 26,5 31,0 43,4 52,2 62,1 77,4 86,2 95,5 112,5 144,2
Flow (m³/h)
consumption in that condition.
7,9 10,0 11,6 16,0 20,2 23,0 29,0 33,2 36,2 41,4 51,0
14 CG-PRC002E-EN
Performance
Data 50 HZ
Tab. 06a - Performance Data - R- 407C (TSA = 4ºC) Tab. 06e - Performance Data - R- 407C (TSA = 8ºC)
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
30 (kW) 15,3 19,8 23,5 31,8 39,1 47,1 57,8 65,4 72,6 82,0 102,2 120,9 30 (kW) 15,8 20,4 24,3 32,8 40,3 48,6 60,0 67,9 75,2 86,2 107,2 126,7

Flow (m³/h) 8,4 10,6 12,3 16,9 21,2 24,3 30,5 34,8 38,2 42,2 52,8 64,2 Flow (m³/h) 9,4 11,9 13,8 18,9 23,8 27,3 34,3 39,3 42,9 48,4 59,8 73,0
35 (kW) 17,1 21,9 25,8 35,4 43,2 51,7 63,9 71,9 79,7 90,1 113,1 132,2 35 (kW) 17,6 22,6 26,7 36,5 44,4 53,5 66,2 74,5 82,5 94,3 118,4 138,2
Flow (m³/h) 8,0 10,2 11,7 16,2 20,3 23,3 29,3 33,4 36,5 40,5 50,2 60,7 Flow (m³/h) 9,0 11,4 13,2 18,2 22,9 26,2 32,9 37,7 41,1 45,8 56,3 69,5
40 (kW) 19,0 24,2 28,4 39,5 47,8 57,0 70,8 79,1 87,6 99,1 125,8 144,8 40 (kW) 19,5 25,0 29,3 40,6 49,2 58,8 73,1 81,9 90,7 103,4 131,3 151,0
Flow (m³/h) 7,7 9,7 11,2 15,5 19,4 22,2 27,9 31,8 34,8 37,8 46,6 57,2 Flow (m³/h) 8,6 10,9 12,6 17,4 21,8 25,0 31,5 36,0 39,3 43,1 52,8 65,1
45 (kW) 21,2 26,8 31,2 44,1 52,9 62,8 78,2 87,1 96,4 110,1 141,9 160,6 45 (kW) 21,8 27,6 32,2 45,2 54,4 64,8 80,8 90,0 99,6 114,2 147,4 166,5
Flow (m³/h) 7,3 9,2 10,6 14,7 18,4 21,1 26,5 30,2 33,1 35,2 43,1 52,8 Flow (m³/h) 8,2 10,3 12,0 16,5 20,8 23,7 29,9 34,2 37,3 39,6 49,3 60,7
Tab. 06b - Performance Data - R- 407C (TSA = 5ºC) Tab. 06f - Performance Data - R- 407C (TSA = 9ºC)
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
30 (kW) 15,4 19,9 23,7 32,1 39,3 47,5 58,4 66,0 73,2 83,1 103,4 122,2 30 (kW) 15,8 20,6 24,5 33,0 40,5 49,0 60,6 68,6 76,0 86,2 108,5 128,3
Flow (m³/h) 8,6 10,9 12,6 17,4 21,8 25,0 31,5 35,9 39,3 44,0 54,6 66,0 Flow (m³/h) 9,6 12,3 14,2 19,4 24,5 28,1 35,3 40,4 44,2 48,4 61,6 74,8
35 (kW) 17,2 22,0 26,0 35,7 43,5 52,2 64,6 72,5 80,4 91,2 114,4 133,7 35 (kW) 17,7 22,8 26,9 36,7 44,8 53,9 66,9 75,2 83,3 94,3 119,9 139,8
Flow (m³/h) 8,3 10,5 12,1 16,7 20,9 24,0 30,2 34,4 37,7 41,4 51,0 62,5 Flow (m³/h) 9,2 11,8 13,6 18,7 23,5 26,9 33,9 38,8 42,3 45,8 58,1 71,3
40 (kW) 19,2 24,4 28,6 39,8 48,2 57,5 71,3 79,8 88,3 100,1 127,1 146,3 40 (kW) 19,7 25,1 29,6 40,9 49,5 59,3 73,8 82,6 91,4 103,4 132,8 152,6
Flow (m³/h) 7,9 10,0 11,5 15,9 20,0 22,9 28,8 32,8 35,9 38,7 48,4 59,0 Flow (m³/h) 8,8 11,2 13,0 17,8 22,5 25,7 32,4 37,0 40,4 43,1 54,6 66,9
45 (kW) 21,4 27,0 31,5 44,4 53,3 63,3 78,9 87,8 97,2 111,1 143,2 162,0 45 (kW) 21,9 27,8 32,5 45,4 54,8 65,2 81,4 90,7 100,5 114,2 148,9 168,1
Flow (m³/h) 7,5 9,5 11,0 15,1 19,0 21,7 27,3 31,2 34,1 36,1 44,9 55,4 Flow (m³/h) 8,4 10,7 12,3 17,0 21,4 24,4 30,8 35,2 38,4 39,6 51,0 62,5
Tab. 06c - Performance Data - R- 407C (TSA = 6ºC) Tab. 06g - Performance Data - R- 407C (TSA = 10ºC)
Temp. de Saída da Água Water Leaving Temperature
020
025
030
040
050
060
070
080
090
100
120
150
020
025
030
040
050
060
070
080
090
100
120
150
= 6ºC = 10ºC
30 (kW) 15,6 20,1 23,9 32,2 39,6 47,8 61,7 66,7 73,9 84,0 104,5 123,7 30 (kW) 15,9 20,8 24,7 33,2 40,8 49,5 61,1 69,2 76,7 88,3 109,9 129,9
Flow (m³/h) 8,9 11,3 13,0 17,9 22,5 25,8 32,4 37,0 40,5 44,9 56,3 68,6 Flow (m³/h) 9,9 12,6 14,6 19,9 25,2 28,9 36,3 41,6 45,4 51,0 63,4 77,4
35 (kW) 17,3 22,2 26,2 36,0 43,8 52,6 65,1 73,2 81,1 92,2 115,7 135,2 35 (kW) 17,8 23,0 27,1 37,0 45,2 54,4 67,4 76,0 84,1 96,6 121,4 141,5
Flow (m³/h) 8,5 10,8 12,5 17,2 21,6 24,7 31,1 35,5 38,8 43,1 52,8 65,1 Flow (m³/h) 9,5 12,1 14,0 19,2 24,2 27,7 34,9 39,9 43,7 48,4 59,8 73,0
40 (kW) 19,3 24,6 28,9 40,1 48,5 57,9 72,0 80,5 89,2 101,2 128,5 147,8 40 (kW) 19,8 25,3 29,8 41,2 49,9 59,7 74,4 83,3 92,3 105,6 134,3 154,3
Flow (m³/h) 8,1 10,3 11,9 16,4 20,6 23,6 29,7 33,9 37,0 40,5 50,2 61,6 Flow (m³/h) 9,1 11,5 13,4 18,3 23,1 26,4 33,3 38,1 41,6 45,8 56,3 69,5
45 (kW) 21,5 27,1 31,8 44,6 53,6 63,8 79,5 88,5 98,0 112,1 144,6 163,5 45 (kW) 22,0 28,0 32,8 45,8 55,2 65,8 82,1 91,5 101,3 116,4 150,4 169,7
Flow (m³/h) 7,7 9,8 11,3 15,6 19,6 22,4 28,2 32,2 35,2 37,0 46,6 57,2 Flow (m³/h) 8,6 11,0 12,7 17,4 22,0 25,1 31,7 36,2 39,5 42,2 52,8 64,2
Tab. 06d - Performance Data - R- 407C (TSA = 7ºC)

Water Leaving
020
025
030
040
050
060
070
080
090
100
120
150
Temperature = 7ºC
Capacity(Tons) 16,1 20,5 23,7 32,6 41,0 47,0 59,1 67,5 73,8 85,5 105,6 129,5
30 (kW) 15,7 20,2 24,0 32,5 39,9 48,3 59,5 67,3 74,6 85,1 105,9 125,2
Flow (m³/h) 9,1 11,6 13,4 18,4 23,1 26,5 33,4 38,1 41,7 46,6 58,1 70,4
Capacity(Tons) 15,5 19,6 22,7 31,3 39,3 45,0 56,7 64,7 70,7 80,9 101,8 122,8
35 (kW) 17,4 22,4 26,5 36,2 44,2 53,0 65,7 73,9 81,8 93,3 117,0 136,7
Flow (m³/h) 8,7 11,1 12,8 17,7 22,2 25,4 32,0 36,6 40,0 44,0 54,6 66,9
Capacity(Tons) 15,9 20,1 23,3 32,1 40,3 46,1 58,0 66,3 72,4 76,3 94,3 115,8
40 (kW) 19,4 24,8 29,1 40,3 48,8 58,4 72,6 81,2 89,9 102,3 129,9 149,4 Notes:
Flow (m³/h) 8,4 10,6 12,3 16,9 21,2 24,3 30,5 34,9 38,1 41,4 51,9 63,4 (1) These values comply with operation conditions from ARI-590-92.
Capacity(Tons) 14,0 17,8 20,6 28,4 35,7 40,8 51,4 58,7 64,1 70,4 87,6 107,7
(2) The column Consumption (kW) represents the nominal compressor
45 (kW) 21,6 27,4 32,1 44,9 54,0 64,3 80,2 89,3 98,8 113,2 146,0 165,0
consumption in that condition.
Flow (m³/h) 7,9 10,0 11,6 16,0 20,2 23,0 29,0 33,2 36,2 38,7 47,5 59,0
CG-PRC002E-EN 15
Acustic Pressure
Levels
Tab. 07 - Cooled liquid CGAD series.
Equipment Acustic Pressure (dbA) of 10 meters

CGAD020C 64
CGAD025C 65
CGAD030C 65
CGAD040C 67
CGAD050C 68
CGAD060C 68
CGAD070C 70
CGAD080C 72
CGAD090C 72
CGAD100C 72
CGAD120C 74
CGAD150C 74
Notes: Measurements are made on the side of equipment at distance of 10 meters. Measurements
smaller than 10 meters may provide diferents results because the large size of equipment and different
sources of noise located in defferent positions.
16 CG-PRC002E-EN
Independent
Controls Controls
Control Module
Emergency Stop - An NC contact or
Trane do Brasil makes the latest
external switch can be used to switch the
microprocessor control technology
unit off in emergencies. The unit must then
available to its clients. The CH530
be restarted manually using the DynaView.
controller with the DynaView control
This facility allows the unit to be switched
module. The DynaView has a touch
off by a fire alarm system, for example.
sensitive liquid crystal display which gives
the user access to all information about
Optional Controls
configuration, operating mode,
Trane also offers an extremely wide range
temperatures, electrical data, pressures
of controls which are intended for
and diagnostics.
applications specific to individual
installations.
Safety Controls
The controller also provides a high level of
Remote Adjustment of the Chilled Water
protection for the equipment, by constantly
Setpoint
monitoring the evaporator and condenser
The chilled water setpoint can be
pressure, current, voltage and temperature
Remote On/ Off - The unit can be switched controlled remotely by means of an analog
variables. When one of these variables
on or off remotely by means of an NC input, using a 0-10VDC or 4-20mA signal.
approaches a limit which could cause the
(normally closed) contact or switch..
unit to switch off, the controller starts a
Signalling Relays
number of actions, such as stepping the
Water Pump Interlock -The equipment A set of 4 programmable relays can be
compressors and fans, in order to keep
will be notified if there is water flow in the used for remote signaling of the unit's
the equipment working before taking the
evaporator by means of an auxiliary operational status, such as maximum
final decision to take it out of service. In
contact in the water pump contactor and a capacity, operation at the limit,
normal operation, the controller will always
flow switch. compressors in operation and alarm
optimize the unit's operation by stepping
signaling.
the compressors and fans so as to ensure
Water Pump Control -The controller has
the best energy efficiency level for the
an output to activate the evaporator water Ice Making and Demand Control
equipment operating conditions.
pump contactor; an external control is The equipment can be put into ice making
therefore not required to activate it. mode externally by means of an NO
External Controls
(normally open) contact. Unit demand
The controller provides a number of
Hot Gas Bypass Valve Control- When the control can be carried out by means of an
different controls using external signals,
Hot Gas Bypass valve option is requested, NC (normally closed) contact in another of
thus making equipment operation more
the controller has an output for operating this module inputs.
flexible.
the valve based on the operational
information which the user sets in the COMM3 Interface- This interface will
DynaView controller. enable the equipment to be
interconnected to the Trane Tracer Summit
control and management system.
CG-PRC002E-EN 17
Protections and
Controls Operational Functions
Operational Protection Measures and High Pressure Protection Starting in Cold Areas
Functions - The main operational The controller constantly monitors the When the equipment is installed in a
protection measures and functions pressure regulator installed in the location where the ambient or outdoor
available are described below: equipment discharge line and shuts the temperature is low, there is a possibility
circuit down when pressure greater than that the equipment will be switched off
Compressor Internal Thermostats - the set maximum is detected. because of low pressure before there is
Trane compressors have internal enough condensing pressure to send the
thermostats to protect the motor windings, . refrigerant back to the evaporator.
which are constantly monitored by the Low Pressure Limit Therefore, cutout due to low pressure will
controller. The controller will restrict the operation of be ignored for a period; this period will vary
the compressors, by switching them off or according to the outdoor temperature at
Inversion and No Phase not allowing other compressors to start, the location.
The controller monitors the phase when the suction pressure approaches
sequence and the presence of current in the set cutout pressure. Operational Recovery and Service
each phase by means of current sensors Recovery
installed in each of the supply phases. External Temperature Cutout - Operation In equipment with reciprocating
of the equipment can be controlled by the compressors, recovery ensures that, when
Overload Relay temperature of the outdoor air, i.e. the started again, the liquid left in the
The supply for each compressor is via an equipment will only go into operation when evaporator is not sucked in by the com-
overload relay, which is constantly the outdoor air temperature is above the pressor, thus damaging it.
monitored by the controller, which turns the temperature set in the controller. If the Unlike reciprocating ones, scroll
compressor off when an overload is equipment is working, it will be switched compressors tolerate flood back. However,
detected. off when the outdoor air temperature when required, operational recovery of the
reaches the set temperature. refrigerant after the equipment or circuit in
Balancing Starts / Operating Hours operation has stopped can be undertaken.
The controller optimizes the start Automatic Adjustment of the Chilled In order to be able to use this function the
sequence for the compressors by Water Setpoint - The controller can equipment must be equipped with
balancing the number of starts and the provide automatic adjustment of the chilled solenoid valves in the liquid line. The
number of hours for each compressor, and water temperature setpoint based on the purpose of service recovery is to recover
does not allow one compressor to have a outdoor air temperature or on the return the refrigerant into the condenser so that
greater operating regime than the others. temperature of the water. maintenance work can be carried out. This
This kind of adjustment offers better recovery can only be done manually from
Evaporator Water Flow ambient temperature comfort control, as the controller. Optional valves in the
A suitable flow switch must be installed well as providing energy savings and compressors suction and discharge can
and electrically connected to the controller allowing the customer to find the best be requested.
in order to report water flow in the system control point.
evaporator. This ensures that the
equipment either does not go into Capacity Limiting during Starting - When
operation or is shut down if there is no the equipment goes into operation and the
water flow. leaving water temperature is above 19ºC,
the controller will not allow the second
Anti-freeze Protection compressor to go into operation until the
The controller monitors the leaving water leaving water temperature drops below
temperature and will disable the 19ºC. This prevents the equipment from
compressors when the water temperature being switched off due to high discharge
reaches the set cutout temperature. pressure because of compressor
overload.
18 CG-PRC002E-EN
Integrated Comfort
Controls System
The owner of an establishment or building

can monitor the chiller fully from the Tracer
Modem
system, as all the monitoring information
shown on the unit controller can be read
Remote Workstation Workstation Workstation
PC PC (Notebook)
from the Tracer system display.
Furthermore, all the diagnostic information
LAN
can be read in the tracer system. Best of
all, these powerful features are achieved
with only one twisted pair of wires. The
chillers can interface to a range of external
control systems, from simple independent
Building Building units to ice making systems.
Control Unit Control Unit
A single twisted pair of wires connected
VariTrane® directly between the chiller and a Tracer
Variable Air Volume
Summit system provides control,
monitoring and diagnostic capabilities.
Control functions include switch on/ switch
off, adjustment of the leaving water
temperature setpoint, blocking compres-
sor operation for demand limiting and
Air Handler Unit control of ice making mode. The Tracer
system reads the monitoring information,
Room Temperature
Sensor Diffuser
such as entering and leaving evaporator
water temperatures and outdoor
®
VariTrane temperature. The Tracer system can read
Variable Air Volume
Terminal a large number of individual diagnostics
on equipment being controlled/ monitored.
In addition to this, it can provide
Exhaust Fan
sequencing control for up to 25 units on
the same system.
Required Options
COMM3 Communications Interface
Room Temperatura
Sensor Liquid Chiller
Diffuser
CGAD Trane Required Devices
Building Control Unit (BCU) and Tracer
Tracer Summit - Trane Integrated . Operating and maintenance time Summit management software.
Comfort System (ICS) . Trend log
The Tracer Summit Building Management . PID control loop
System with Chiller Control provides
building automation and energy Of course, Trane Chiller Control can also
management functions using independent be used independently or in conjunction
control. The Chiller Control is able to with a complete building automation
monitor and control the complete installed system.
chiller system. When one or more chillers are used with a
Available applications: Tracer Summit system from Trane, the
. Time programmer; units can be monitored and controlled
. Demand limiter from a remote location.
. Chiller sequencing The chillers can fit into a global building
. Process control language. automation strategy by using scheduling,
. Boolean processing. programmed changes, demand limiting
. Ambient controllers and chiller sequencing.
. Reports and logs
. Personalized messages
CG-PRC002E-EN 19
Integrated Comfort
Controls System
Ice Making System Controls chillers in order to ensure equal operating chiller's tubing is not detected, the start
The ice making option can be requested time and wear between chillers. sequence is interrupted in order to protect
with the chiller. The unit will have two
Trane chiller automation allows unique the chiller and the next chiller within the
operating modes, ice making and normal strategies for energy saving. An example is sequence is immediately started up to
chilling. In ice making mode the chiller will the control of pumps and chillers based on maintain chilling. Should a problem occur,
operate at total compressor capacity until
a view of the total energy consumption of the operator receives an alarm warning
the return solution temperature matches the system. The software intelligently and a diagnostic message to help solve
the setpoint for ice making. The chiller evaluates and selects the option with least the problem quickly and accurately. An
needs two input signals. The first is an on/
energy consumption. instant report showing the system status
off signal for scheduling and the second is
immediately before it was switched off
required to switch the unit between ice Keeping Operators Informed helps operators identify the cause. If the
making mode and normal operation. The
It is vital for efficient chiller operation to emergency conditions warrant an
signals are supplied by a remote building ensure that operational personnel have immediate manual shutdown the operator
automation device, such as, for example, a instant information on what is happening can ignore the automatic control.
timer or a manual switch. The signals can
in the equipment. By clearly describing the
also be supplied by the Tracer System. chiller system, drawings with schematic
layouts of chillers, tubing, pumps and Documentation
Additional Options which Can Also Be
towers allow building operational staff to The comprehensive documentation
Used monitor all the conditions efficiently. Status covering chiller management practices is
- Signalling Relays screens show the current conditions and now a fact of life. Trane chiller system
control actions which have to be taken in automation generates the reports defined
Further Tracer Summit Characteristics- order to increase or decrease chiller in the ASHRAE Guidelines.
Trane Chiller Systems Automation capacity.
Trane's experience in chillers and controls
Chillers can be monitored and controlled ICS or Integrated Comfort System
makes us the preferred choice for chiller from a remote location. The Tracer Summit Capabilities
automation. The Tracer Summit building provides standardized report templates When it is integrated with a tracer Summit
automation system from Trane has chiller
which list key operational data for problem management system, Trane chiller
control capabilities which are unparalleled solving and performance checking. The automation manages the coordination
in the industry. Our chiller automation reports for each type of chiller and for chiller with the Tracer Summit applications in
software is fully developed and tested by
sequencing systems are also order to optimize global building operation.
Trane. standardized. Detailed reports with chiller With this system option, a large part of
operating times help in planning preventive Trane's HVAC* and control experience is
Energy Efficiency
maintenance. used to provide solutions for different parts
Trane chiller automation manages chiller
of the installation. If your project requires
starts so as to optimize the total energy Rapid Response in Emergencies an interface to other systems the Tracer
efficiency of the equipment. Sophisticated
We appreciate the importance of Summit system can share data using
software automatically determines which maintaining chilled water production and at BACNet, the ASHRAE open systems
chiller should be operating in response to the same time protecting your chillers from protocol, MODBUS and other protocols
the current conditions. The software also
expensive damage. If water flow into a (subject to confirmation).
switches automatically between individual *HVAC = Heating, Ventilation and Air Conditioning.
20 CG-PRC002E-EN
Electrical
Data
Tab. 08 - Electrical Data - 60 Hz

60 H z
220V 380V 440V
M o d elo s C o m p o n e n te s N o m in a l S ta rt MCA F use N o m in a l S ta rt MCA F use N o m in a l S ta rt MCA F use
C u rr e n t ( A ) C u r re n t(A ) C u rr e n t ( A ) C u r re n t(A ) C u rr e n t ( A ) C u r re n t(A )
C o m p re s s o r e s 6 5 ,2 3 8 ,4 3 0 ,3
C G AD 020 Fans 8 ,2 3 1 0 ,0 8 8 ,0 1 2 5 ,0 4 ,7 1 8 3 ,0 5 4 ,0 7 0 ,0 4 ,2 1 4 3 ,0 4 5 ,0 6 0,0
T o ta l 7 3 ,4 4 3 ,1 3 4 ,5
C o m p re s s o r e s 7 8 ,9 4 7 ,8 3 7 ,7
C G AD 025 Fans 1 2 ,3 3 2 8 ,0 1 1 0 ,0 1 5 0 ,0 7 ,1 1 9 5 ,0 6 8 ,0 1 0 0 ,0 6 ,3 1 5 3 ,0 5 7 ,0 8 0,0
T o ta l 9 1 ,2 5 4 ,8 4 4 ,0
C o m p re s s o r e s 9 2 ,5 5 7 ,2 4 5 ,1
C G AD 030 Fans 1 2 ,3 4 4 3 ,0 1 3 5 ,0 1 7 5 ,0 7 ,1 2 7 5 ,0 7 8 ,0 1 0 0 ,0 6 ,3 2 0 8 ,0 6 5 ,0 8 0,0
T o ta l 1 0 4 ,8 6 4 ,2 5 1 ,4
C o m p re s s o r e s 1 3 0 ,4 7 6 ,7 6 0 ,5
C G AD 040 Fans 1 6 ,4 3 8 3 ,0 1 6 3 ,0 2 0 0 ,0 9 ,4 2 2 6 ,0 9 7 ,0 1 1 0 ,0 8 ,4 1 7 8 ,0 8 0 ,0 9 0,0
T o ta l 1 4 6 ,8 8 6 ,1 6 8 ,9
C o m p re s s o r e s 1 5 7 ,7 9 5 ,5 7 5 ,4
C G AD 050 Fans 2 4 ,6 4 1 9 ,0 2 0 9 ,0 2 5 0 ,0 1 4 ,1 2 5 0 ,0 1 2 3 ,0 1 5 0 ,0 1 2 ,6 1 9 7 ,0 1 1 0 ,0 1 2 5 ,0
T o ta l 1 8 2 ,3 1 0 9,6 8 8 ,0
C o m p re s s o r e s 1 8 5 ,0 1 1 4,4 9 0 ,2
C G AD 060 Fans 2 4 ,6 5 4 7 ,0 2 3 0 ,0 3 0 0 ,0 1 4 ,1 3 3 9 ,0 1 4 2 ,0 1 7 5 ,0 1 2 ,6 2 5 9 ,0 1 1 6 ,0 1 5 0 ,0
T o ta l 2 0 9 ,6 1 2 8,5 1 0 2,8
C o m p re s s o r e s 2 2 2 ,9 1 3 3,9 1 0 5,6
C G AD 070 Fans 2 4 ,6 6 2 4 ,0 2 7 0 ,0 3 0 0 ,0 1 4 ,1 3 6 7 ,0 1 6 3 ,0 2 0 0 ,0 1 2 ,6 2 8 7 ,0 1 3 0 ,0 1 5 0 ,0
T o ta l 2 4 7 ,5 1 4 8,0 1 1 8,2
C o m p re s s o r e s 2 5 0 ,2 1 5 2,7 1 2 0,5
C G AD 080 Fans 3 2 ,8 7 6 1 ,0 3 1 0 ,0 3 5 0 ,0 1 8 ,8 4 6 1 ,0 1 9 2 ,0 2 0 0 ,0 1 6 ,8 3 5 4 ,0 1 5 0 ,0 1 7 5 ,0
T o ta l 2 8 3 ,0 1 7 1,5 1 3 7,3
C o m p re s s o r e s 2 7 7 ,6 1 7 1,5 1 3 5,3
C G AD 090 Fans 3 2 ,8 8 8 9 ,0 3 3 0 ,0 4 0 0 ,0 1 8 ,8 5 5 0 ,0 2 1 0 ,0 2 2 5 ,0 1 6 ,8 4 1 6 ,0 1 7 0 ,0 2 0 0 ,0
T o ta l 3 1 0 ,4 1 9 0,3 1 5 2,1
C o m p re s s o r e s 3 5 9 ,0 2 1 3,2 1 5 7,4
C G AD 100 Fans 3 6 ,3 8 7 0 ,0 4 2 5 ,0 5 0 0 ,0 2 1 ,0 4 9 0 ,0 2 5 5 ,0 3 0 0 ,0 1 6 ,5 4 0 9 ,0 1 9 0 ,0 2 2 5 ,0
T o ta l 3 9 5 ,3 2 3 4,2 1 7 3,9
C o m p re s s o r e s 4 2 6 ,4 2 5 1,7 1 8 7,3
C G AD 120 Fans 4 8 ,4 1 2 5 7 ,0 5 0 0 ,0 5 0 0 ,0 2 8 ,0 7 2 0 ,0 2 9 5 ,0 3 0 0 ,0 2 2 ,0 5 8 1 ,0 2 2 5 ,0 2 5 0 ,0
T o ta l 4 7 4 ,8 2 7 9,7 2 0 9,3
C o m p re s s o r e s 5 3 8 ,6 3 1 9,7 2 3 6,7
C G AD 150 Fans 6 0 ,5 1 5 4 5 ,0 6 3 0 ,0 7 0 0 ,0 3 5 ,0 8 6 3 ,0 3 7 6 ,0 4 0 0 ,0 2 7 ,5 7 3 0 ,0 2 8 4 ,0 3 0 0 ,0
T o ta l 5 9 9 ,1 3 5 4,7 2 6 4,2
Tab. 09 - Electrical Data - 50 Hz

50 H z
380V
M o d e lo s C o m p o n e n te s N o m in a l S ta rt M CA Fuse
C u rre n t (A ) C u rre n t(A )
C om p re s s o re s 2 9 ,7
C G AD 020 F ans 4 ,4 1 4 3 ,0 4 5 ,0 6 0 ,0
T o ta l 3 4 ,1
C G AD 025 F ans 6 ,6 1 5 4 ,0 5 7 ,0 8 0 ,0
T o ta l 4 4 ,4
C G AD 030 F ans 6 ,6 2 0 9 ,0 6 5 ,0 8 0 ,0
T o ta l 5 2 ,5
C G AD 040 F ans 8 ,8 1 7 7 ,0 8 0 ,0 9 0 ,0
T o ta l 6 8 ,1
C G AD 050 F ans 1 3 ,2 1 9 8 ,0 1 1 0 ,0 1 2 5 ,0
T o ta l 8 8 ,8
C G AD 060 F ans 1 3 ,2 2 6 1 ,0 1 1 6 ,0 1 5 0 ,0
T o ta l 1 0 5 ,1
C om p re s s o re s 1 0 5 ,3
C G AD 070 F ans 1 3 ,2 2 8 7 ,0 1 3 0 ,0 1 5 0 ,0
T o ta l 1 1 8 ,5
C G AD 080 F ans 1 7 ,6 3 5 5 ,0 1 5 0 ,0 1 7 5 ,0
T o ta l 1 3 9 ,1
C G AD 090 F ans 1 7 ,6 4 1 8 ,0 1 7 0 ,0 2 0 0 ,0
T o ta l 1 5 5 ,4
C G AD 100 F ans 1 4 ,7 4 0 6 ,0 1 9 0 ,0 2 2 5 ,0
T o ta l 1 7 1 ,4
C G AD 120 F ans 1 9 ,6 5 7 7 ,0 2 2 5 ,0 2 5 0 ,0
T o ta l 2 0 4 ,9
NOTES: C om p re s s o re s 2 3 5 ,0
(1)Values of operation conditions are based on ARI 590-92 C G AD 150 F ans 2 4 ,5 7 2 6 ,0 2 8 4 ,0 3 0 0 ,0
(2)MCA: Minimum Circuit Ampacity T o ta l 2 5 9 ,5
CG-PRC002E-EN 21
Dimensional
Data CGAD020
Fig. 09 - Unit Dimensions - CGAD 020

DIMENSÕES DA UNIDADE CGAD 020
FREE
2200 DESCARGA LIVRE
DISCHARGE
CONTROLE MICROPROCESSADO
AIR FLOW
CONTROL
CH530 SYSTEM
120
200
CH530
AIR FLOW QUADRO ELÉTRICO AIR FLOW

ELETRIC FRAME
1840
1720
ENTRADA
POWER
74.5 DE FORÇA
343
SUPPLY
(SEE(NOTA
NOTE3)3)
198.5 (NOTE
1603.5 (NOTA 1) 1) 198.5 70.5 (NOTE1)1)
1208.5 (NOTA 70.5 204 1509 287
2000 1350
SAÍDA DECHILLED WATER
ÁGUA GELADA CHILLED
ENTRADA WATER
DE ÁGUA GELADA
OUTLET (VICTAULIC
ACOPLAMENTO VICTAULIC 2" 2”) INTLET (VICTAULIC
ACOPLAMENTO VICTAULIC2”)
2"
NOTAS:
Notas:
NOTES: 1 - Pontos de fixação para isoladores de vibração ( 4 furos c/ diâmetro 13 mm)
1 - Pontos de fixação para isoladores de vibração (4 furos c/ diâmetro 13mm)
1 - FIXING2POINTS
- Os isoladores
FOR VIBRATION
de vibraçãoINSULATORS
são opcionais. (4 X.13mm DIAM HOLES)
32-- AOs
2 - VIBRATION isoladores
INSULATORS
furação de vibração
ARE
para entrada NOT são
SUPPLIED
dos cabos opcionais
WITH
elétricos THE
deverá serEQUIPMENT.
realizada em campo pelo instalador.
3 - THE ORIFICE
43--Unidade:
FORmm
A furaçãoENTRY
para OF ELECTRICAL
entrada dos cabos CABLES SHOULD
elétricos deverá BEser realizada em campo pelo instalador 3 1
CARRIED OUT IN THE FIELD BY THE INSTALLER.
4 - Unidade: mm
4 - UNITS : mm
Fig. 10 - Maintenance and air circulation clearances
4 2
OPENING OF
ELECTRIC FRAME
22 CG-PRC002E-EN
Dimensional
Data CGAD025
Fig.11 - Unit Dimensions - CGAD 025

DESCARGA
FREE
2200 DISCHARGE
LIVRE
DESCARGA LIVRE CONTROL
CONTROL
AIR FLOW
MICROPROCESADO
200 CONTROL SYSTEM
120
CH530
MICROPROCESADO
CH530
CONTROL
CH530SYSTEM
CH530
CH530
AIR FLOW
ELETRIC FRAME
QUADRO ELÉTRICO AIR FLOW
1840
1720
155
ENTRADA
POWER
DE FORÇA
353
SUPPLY
(NOTA 3)
(SEE NOTE 3)
200 (NOTE
1600 (NOTA 1) 1) 200 70.5 (NOTE
1558.5 (NOTA 1) 1) 70.5 207 1465.5 327.5
2000 1700 CHILLED WATER INTLET

SAÍDA DE ÁGUA
CHILLED GELADA
WATER OUTLET ENTRADA DE ÁGUA GELADA
ACOPLAMENTO VICTAULIC
(VICTAULIC 2.1/2"
2.1/2”) (VICTAULIC
ACOPLAMENTO 2.1/2”)2.1/2"
VICTAULIC
NOTAS:
NOTES:
1 - FIXING POINTS FOR VIBRATION INSULATORS (4 X.13mm DIAM HOLES)
2 - VIBRATION INSULATORS ARE NOT SUPPLIED WITH THE EQUIPMENT.
2 - Os isoladores
3 - THE ORIFICE FOR ENTRY deOF
vibração são opcionais
ELECTRICAL CABLES SHOULD BE
CARRIED3OUT IN THE FIELD
- A furação BY THE INSTALLER.
para entrada dos cabos elétricos deverá ser realizada em campo pelo instalador 3 1
4 - UNITS : mm
4 - Unidade: mm
4 2
OPENING OF
ELECTRIC FRAME
CG-PRC002E-EN 23
Dimensional
Data CGAD030
Fig.13 - Unit Dimensions - CGAD 030

2200
DESCARGA LIVRE
FREE
200 DISCHARGE
120
CH530
AIR FLOW
CONTROL SYSTEM
CH530
QUADRO ELÉTRICO
1840
1720
155
AIR FLOW AIR FLOW
ELETRIC FRAME
ENTRADA
402
DE FORÇA
(NOTA 3)
POWER
200 1600 (NOTA 1) 200 70.5 1558.5 (NOTA 1) 70.5 207 1465.5 327.5 SUPPLY
(SEE NOTE 3)
2000 1700 SAÍDA DE ÁGUA GELADA ENTRADA DE ÁGUA GELADA
ACOPLAMENTO VICTAULIC 2.1/2" ACOPLAMENTO VICTAULIC 2.1/2"
(NOTE 1)
NOTAS:
CHILLED WATER OUTLET CHILLED WATER INTLET
(VICTAULIC 2.1/2”) (VICTAULIC 2.1/2”)
2 - Os isoladores de vibração são opcionais
3 - A furação para entrada dos cabos elétricos deverá ser realizada em campo pelo instalador 3 1
NOTES: 4 - Unidade: mm
3 - THE ORIFICE FOR ENTRY OF ELECTRICAL CABLES SHOULD BE
4 - UNITS : mm
4 2
OPENING OF
ELECTRIC FRAME
24 CG-PRC002E-EN
Dimensional
Data CGAD 040

2394 FREE
DISCHARGE
DESCARGA LIVRE
CONTROL
AIR FLOW
200 CONTROLE MICROPROCESSADO
MICROPROCESADO
120
CH530
CH530
AIR FLOW
ELETRIC FRAME AIR FLOW
QUADRO ELÉTRICO
2190
2070
ENTRADA
POWER
SUPPLY
DE FORÇA
COMPRESORES
(SEE NOTE
(NOTA 3) 3)
432
230 (NOTE
1734 (NOTA 1) 1) 230 700.5 251.5 1485 458
2194 78.5 (NOTE

1723.5 (NOTA 1) 1) 78.5 SAÍDA DE ÁGUAWATER
GELADAOUTLET ENTRADA DE ÁGUAINTLET
GELADA
CHILLED CHILLED WATER
ACOPLAMENTO VICTAULIC
(VICTAULIC 2.1/2"
2.1/2”) (VICTAULIC VICTAULIC
ACOPLAMENTO 2.1/2”) 2.1/2"
1880
NOTES:
1 - FIXING POINTS FOR VIBRATION INSULATORS (4 X.13mm DIAM HOLES) 3 1
2 - Notas:
VIBRATION INSULATORS ARE NOT SUPPLIED WITH THE EQUIPMENT.
3-1 - Pontos
THE de fixação
NOTAS:
ORIFICE para isoladores
FOR ENTRY de vibração CABLES
OF ELECTRICAL ( 4 furos c/SHOULD
diâmetro 13
BEmm)
2 - Os isoladores
CARRIED OUT IN THEde vibração
FIELD BYsãoTHE
opcionais.
INSTALLER.
3 - A furação
4 - UNITS : mm para entrada dos cabos elétricos deverá ser realizada em campo pelo instalador.
4 - Unidade: mm
3 - A furação para entrada dos cabos elétricos deverá ser realizada em campo pelo instalador
Fig. 164 -- Unidade: mm
Maintenance and air circulation clearances
4 2
OPENING OF
ELECTRIC FRAME
CG-PRC002E-EN 25
Dimensional
Data CGAD 050

FREE
2992.5 DISCHARGE
DESCARGA LIVRE
AIR FLOW
200 CONTROLE MICROPROCESSADO
120
CONTROL
CH530 SYSTEM
CH530
AIR FLOW AIR FLOW

ELETRIC
QUADRO ELÉTRICO
FRAME
2190
2070
ENTRADA
POWER
COMPRESSORS
COMPRESSORES COMPRESSORS
COMPRESSORES
DE FORÇA
SUPPLY
(NOTA
(SEE 3) 3)
NOTE
414
230 2332.5 (NOTA
(NOTE1) 1) 230 685 306 1978.5 508
2792.5 81 1718 (NOTA

(NOTE1) 1) 81 CHILLED
SAÍDA DE ÁGUA GELADAWATER CHILLED
ENTRADA WATER
DE ÁGUA GELADA
OUTLET
ACOPLAMENTO (VICTAULIC
VICTAULIC 3" 3”) INTLET (VICTAULIC
ACOPLAMENTO 3”) 3"
VICTAULIC
1880
NOTAS:
NOTES:
1 -Notas:
FIXING POINTS FOR VIBRATION INSULATORS (4 X.13mm DIAM HOLES) 3 1
- Pontos1de- fixação
2 -1VIBRATION Pontos de fixação
para
INSULATORS ARE para
isoladores isoladores
de vibração
NOT SUPPLIED de vibração
( 4 furos
WITH c/ THE (413
diâmetro furos
mm)c/ diâmetro 13mm)
EQUIPMENT.
3 -2THE
- Os ORIFICE
isoladores de
2 - OsFOR vibração
ENTRYsão
isoladores de opcionais.
OFvibração são opcionais
ELECTRICAL CABLES SHOULD BE
3 - A furação
CARRIED OUT paraTHE
entrada dos cabos
THEelétricos deverá ser realizada em campo pelo instalador.
3 - AINfuração FIELD
paraBYentrada INSTALLER.
dos cabos elétricos deverá ser realizada em campo pelo instalador
4 -4UNITS
- Unidade:
: mmmm
4 - Unidade: mm
4 2
OPENING OF
ELECTRIC FRAME
26 CG-PRC002E-EN
Dimensional
Data CGAD 060

2992.5 FREE
DISCHARGE
DESCARGA LIVRE
AIR FLOW
200 120 CONTROL
CH530 SYSTEM
CH530
AIR FLOW
ELETRIC AIR FLOW
FRAME
QUADRO ELÉTRICO
2190
2070
POWER
ENTRADA
COMPRESSORES COMPRESSORES
DESUPPLY
FORÇA
COMPRESSORS COMPRESSORS
(SEE
(NOTANOTE
3) 3)
401
230 2332.5 (NOTA
(NOTE1) 1) 230 679 307 1978.5 507.5
2792.5 81 1718 (NOTA

(NOTE1) 1) 81
SAÍDA DE ÁGUA GELADA
CHILLED WATER ENTRADA DE ÁGUA
CHILLED WATERGELADA
1880 ACOPLAMENTO
OUTLETVICTAULIC 4"
(VICTAULIC 4”) ACOPLAMENTO
INTLET VICTAULIC
(VICTAULIC 4”) 4"
NOTAS:
NOTES: 1 - Pontos de fixação para isoladores de vibração (4 furos c/ diâmetro 13mm) 3 1

2 - VIBRATION2 - INSULATORS
Os isoladoresARE
de vibração são opcionais
NOT SUPPLIED WITH THE EQUIPMENT.
3 - A FOR
3 - THE ORIFICE furação para OF
ENTRY entrada dos cabos
ELECTRICAL elétricos
CABLES deverá BE
SHOULD ser realizada em campo pelo instalador
CARRIED OUT IN THE FIELD
4 - Unidade: mm BY THE INSTALLER.
4 - UNITS : mm

4 2
OPENING OF
ELECTRIC FRAME
CG-PRC002E-EN 27
Dimensional
Data CGAD 070

FREE
3700 DISCHARGE
DESCARGA LIVRE
AIR FLOW
120
199.5 CONTROL SYSTEM

CH530
CH530
AIR FLOW ELETRIC AIR FLOW

QUADRO ELÉTRICO
FRAME
714.5
2190
2070
POWER
ENTRADA
CCOMPRESSORES
OMPRESORES COMPRESSORS
COMPRESSORES DESUPPLY
FORÇA
(SEE NOTE
(NOTA 3) 3)
495
230 1520 (NOTA
(NOTE1) 1) 1520 (NOTE
(NOTA 1)
1) 230 81 1718 (NOTA
(NOTE1)1) 81 1644 928
3500 1880
CHILLED
SAÍDA DE ÁGUA GELADA WATER CHILLED
ENTRADA DE ÁGUAWATER
GELADA
OUTLET
ACOPLAMENTO 4”)
VICTAULIC 4"
NOTES:
Notas: NOTAS:
11- -FIXING
PontosPOINTS
de fixaçãoFOR
paraVIBRATION INSULATORS
isoladores de (6 X.13mm
vibração ( 6 furos DIAM
c/ diâmetro 13 HOLES)
mm)
22- -VIBRATION
Os isoladoresINSULATORS
de vibração ARE
são NOT SUPPLIED WITH THE EQUIPMENT.
opcionais. 1 2 3
33- -THE 1 - Pontos
ORIFICE de fixação para isoladores de vibração (6
BEfuros c/ diâmetro 13mm)
A furação paraFOR ENTRY
entrada OF ELECTRICAL
dos cabos CABLES
elétricos deverá SHOULD
ser realizada em campo pelo instalador.
CARRIED
4 - Unidade:2OUT
-mm
Os INisoladores
THE FIELD de vibração
BY THE são opcionais
INSTALLER.
4 - UNITS :3mm - A furação para entrada dos cabos elétricos deverá ser realizada em campo pelo instalador
4 - Unidade: mm
VENTILADORES
4 5 6
OPENING OF
ELECTRIC FRAME
28 CG-PRC002E-EN
Dimensional
Data CGAD 080
Fig. 23 - Dimensiones de la Unidad CGAD 080

FREE
3908 DISCHARGE
DESCARGA LIVRE
AIR FLOW
199.5 120 CONTROL
CH530 SYSTEM
CH530
AIR FLOW
ELETRIC
AIR FLOW
FRAME
QUADRO ELÉTRICO
713.5
2190
2070
EVAPORADOR
EVAPORADOR
ENTRADA
POWER
DE FORÇA
COMPRESSORS COMPRESSORS SUPPLY
(NOTA 3)
(SEE NOTE 3)
495
230 1624 (NOTA
(NOTE1) 1) 1624 (NOTA
(NOTE1) 1) 230 81 1718.5 (NOTA
(NOTE1)1) 81 1644 1032
3708 1880
SAÍDA DE ÁGUACHILLED
GELADA WATER ENTRADACHILLED WATER
DE ÁGUA GELADA
OUTLET
VICTAULIC 4" INTLET (VICTAULIC
4”) ACOPLAMENTO VICTAULIC 4" 4”)
NOTAS:
Notas:
NOTES:1 - Pontos de fixação para isoladores de vibração ( 6 furos c/ diâmetro 13 mm)
21-POINTS
1 - FIXING -Os
Pontos de fixação
isoladores
FOR de para
vibração
VIBRATION isoladores
são opcionais. de(6mm
INSULATORS vibração
DIAM(6 furos c/ diâmetro 13mm)
HOLES) 1 2 3
32- -AOs
2 - VIBRATION furação para entrada
INSULATORS
isoladores deARE dos
NOT cabos
vibração elétricos
SUPPLIED
são deveráTHE
WITH
opcionais ser realizada em campo pelo instalador.
EQUIPMENT.
4 - Unidade:
3 - THE ORIFICE mm
FOR ENTRY OF ELECTRICAL
3 - A furação para entrada dos cabosCABLES
elétricosBE CARRIED
deverá ser realizada em campo pelo instalador
OUT IN THE FIELD BY THE INSTALLER.
4 - UNITS4: -mmUnidade: mm

4 5 6
OPENING OF
ELECTRIC FRAME
CG-PRC002E-EN 29
Dimensional
Data CGAD 090

FREE
DISCHARGE
DESCARGA LIVRE
3908
AIR FLOW
120
199.5 CONTROL
CH530 SYSTEM
CH530
AIR FLOW
ELETRIC
AIR FLOW
FRAME
QUADRO ELÉTRICO
713.5
2190
2070
EVAPORADOR
EVAPORATOR
ENTRADA
POWER
COMPRESSORS COMPRESSORS
DESUPPLY
FORÇA
(NOTA 3)
(SEE NOTE 3)
495
230 (NOTE
1624 (NOTA 1) 1) 1624 (NOTA
(NOTE1) 1) 230 81 1718.5 (NOTA
(NOTE1)1) 81 1644 1032
3708 1880
CHILLED
SAÍDA DE ÁGUA GELADA WATER CHILLED
ENTRADA WATER
DE ÁGUA GELADA
OUTLET
ACOPLAMENTO VICTAULIC 4”)
4"
NOTAS:
Notas: 1 2 3
NOTES: 1 - Pontos de fixação para isoladores de vibração ( 6 furos c/ diâmetro 13 mm)

1 - FIXING2 --Os
1POINTS isoladores
Pontos FOR de vibração
deVIBRATION
fixação parasão opcionais.de
isoladores
INSULATORS vibração
(6 X.13mm (6 furos
DIAM c/ diâmetro 13mm)
HOLES)
3 - A INSULATORS
2 - VIBRATION furação para entrada
ARE dos cabos
NOT elétricos
SUPPLIED deverá
WITH THEserEQUIPMENT.
realizada em campo pelo instalador.
4 - Unidade:
3 - THE ORIFICE FORmmENTRY OF ELECTRICAL CABLES SHOULD BE
CARRIED3OUT - A IN
furação para BY
THE FIELD entrada dos cabos elétricos deverá ser realizada em campo pelo instalador
THE INSTALLER.
4 - UNITS :4mm
- Unidade: mm
4 5 6
OPENING OF
ELECTRIC FRAME
30 CG-PRC002E-EN
Dimensional
Data CGAD 100
NOTES: Notas:
1 - FIXING1POINTS
- PontosFOR
de fixação para isoladores
VIBRATION de vibração
INSULATORS (6 X.(17,5
6 furos
mmc/DIAM
diâmetro 13 mm)
HOLES) 2 - Os isoladores de vibração são opcionais.
3 - A furação para entrada dos cabos elétricos deverá
2 - VIBRATION INSULATORS ARE NOT SUPPLIED WITH THE EQUIPMENT. ser realizada em campo pelo instalador.
4 - Unidade:
3 - THE ORIFICE FORmmENTRY OF ELECTRICAL CABLES SHOULD BE
4 - UNITS : mm
OPENING OF
ELECTRIC FRAME
OPENING OF
ELECTRIC FRAME
OPENING OF
ELECTRIC FRAME
CG-PRC002E-EN 31
Dimensional
Data CGAD 120
NOTES:
1 - FIXING POINTS FOR VIBRATION INSULATORS (8 X1 7,5mm DIAM HOLES)
4 - UNITS : mm
OPENING OF
OPENING OF
OPENING OF
32 CG-PRC002E-EN
Dimensional
Data CGAD 150
NOTES:
1 - FIXING POINTS FOR VIBRATION INSULATORS (8 X 17,5mm DIAM HOLES)
4 - UNITS : mm
OPENING OF
OPENING OF
OPENING OF
CG-PRC002E-EN 33
Mechanical
Especifications
Evaporators The copper tubes are internally-rifled, Refrigerating lines

Shell & Tube evaporators are designed seamless tubes, mounted and Trane CGAD Air-Cooled Liquid Chillers are
according to the ASME standard for mechanically expanded in carbon steel equipped with the following refrigerating
pressure vessels, without internal mirrors to avoid refrigerant leaks. In order lines:
combustion, and are factory tested with to avoid tube vibration problems and
225 psig at refrigerant side (tubes) and maintain the crossed drainage of Model Suction Discharge Liquid
150 psig at water side (casing). The evaporator water, traverse baffle plates are
evaporator casing is made of carbon steel mounted along the evaporator. 020 1 5/8" 1 3/8" 7/8"
and the covers are made of cast iron. Thermal insulation of the assembly is 025 2 1/8" 1 3/8" 7/8"
provided by 16-mm rubber sheets.
030 2 1/8" 1 3/8" 7/8"
040 2 x 1 5/8" 2 x 1 3/8" 2 x 7/8"

Internally-Rifled
Copper Tube 050 2 x 2 5/8" 2 x 1 3/8" 2 x 7/8"
Plastic Baffle Plates
060 2 x 2 5/8" 2 x 1 3/8" 2 x 7/8"
Carbon Steel
Mirror 070 2 x 2 5/8" 2 x 1 3/8" 2 x 1 1/8"
080 2 x 2 5/8" 2 x 1 3/8" 2 x 1 1/8"
090 2 x 2 5/8" 2 x 1 3/8" 2 x 1 1/8"
100 2 5/8" 1 5/8" 1 1/8"
120 3 1/8" 1 5/8" 1 1/8"
150 3 1/8" 1 5/8" 1 1/8"

Water Flow
Fig. 33 - Shell & Tube Evaporator
Condensers Global Connector

Coil-type condensers are built with The Global Connectors facilitate the
aluminum fins model Wavy-3B, 3/8"-OD connection of terminals and decrease the
internally-rifled copper tubes, mechanically interference.
expanded in the fins, and galvanized steel They have aesthetically pleasing;
structure, and are equipped with an inte- automotive industry grade; sealed
gral sub-cooler. After manufacturing, connector system; easier connection for
condensers are tested with a pressure factory and field; repeated manual
of 30 kgf/cm2 (425 psig).30 kgf/cm2 disconnection and re-connection allowed.
(425 psig).
Air Flow
Evaporator
Fan Coils
Fig. 34 - Condenser Air Flow Fig. 35 - Global Connector
34 CG-PRC002E-EN
Mechanical
Especifications
Cooling Components Compressor Scroll Compression Cycle

Trane 20, 25 and 30Tons CGAD Air- Compressors Scroll provide more Figure above shows a Scroll compressor
Cooled Liquid Chillers have only one benefits to the air conditioning system user in detail, presenting its main components
cooling circuit, and the 40, 50, 60, 70 , 80 when compared to reciprocating and the operational principle, according to
and 90 Tons units have two independent compressors. the items below:
cooling circuits. Each cooling circuit is
supplied with the following components: - They have a 5 to 10% higher efficiency, in A. The refrigerant, in gaseous state , is
average; suctioned into its interior though the
- Thermostatic expansion valve; - They do have no valves, being extremely suction connection.
- Tank valve at condenser outlet, with a resistant to slugging; B. The refrigerant passes through a
pressure intake point of 1/4" SAE; - They have 64% fewer moving parts; cavidaty between the rotor and the stator,
- Liquid sightglass with humidity indicator; - Extremely smooth and silent operation, cooling the motor .
- Dryer filter; comparable to a centrifugal compressor; C. The refrigerant speed decreases when
- Low torque variation, which provides it leaves the motor cavity and the oil is
vibration and noise reduction and separated. The oil returns to the
increases motor life. crankcase..
D. The refrigerant goes into the suction
chamber and fills out the compression
scroll.
E. After compression, the refrigerant is
dischraged in the compressor hood
through a hole in the center of the fixed
Fig. 36 - Liquid Sightglass Scroll. The hood function is to amortize the
refrigerant flow, reducing vibrations. Then
the refrigerant leaves the compressor
through the discharge connection.
Check Valve
Fixed Scroll
Fig. 37 - Expansion
Valve D
E
Discharge
Moving
C
Fig. 38 - Comparison Scroll x Reciprocal Scroll
B
Filtering Element Motor
Motor
Shaft A
Suction
Oil Pump
Fig. 39 - Drier Filter FIg. 40 - Compressor Scroll
CG-PRC002E-EN 35
General
Dimensions
Tab.10 - General dimensional data

(1) (2)
Height Width Depth Floor Area Operational Weight Shipping Weight
Modelo
2
mm mm mm m kg kg
CGAD020C 1840,5 2195,0 1350,0 2,700 1340 1300
CGAD025C 1840,5 2195,0 1700,0 3,400 1420 1380
CGAD030C 1840,5 2195,0 1700,0 3,400 1480 1420
CGAD040C 2190,5 2389,0 1880,0 3,940 1910 1860
CGAD050C 2190,5 2989,0 1880,0 5,250 2210 2130
CGAD060C 2190,5 2989,0 1880,0 5,250 2500 2360
CGAD070C 2190,5 3695,0 1880,0 6,580 3000 2850
CGAD080C 2190,5 3903,0 1880,0 6,970 3240 3100
CGAD090C 2190,5 3903,0 1880,0 6,970 3220 3100
CGAD100C 2376,0 3425,0 2442,0 7,237 3775 3653
CGAD120C 2376,0 4949,0 2442,0 10,654 4135 3962
CGAD1500C 2376,0 4949,0 2442,0 10,654 4653 4376
ELECTRICAL
PA N E L
HEIGHT
HEIGHT
(1)
WIDHT
(1)
HT
WID
DEPTH
DEPTH
Fig. 41 -- Dimensional drawing
Notas:
(1) The length measurements take into account the depth of the electrical frame coupled to the equipment.
(2) The floor area measurements do not take into account the base of the electrical frame coupled to the equipment.
36 CG-PRC002E-EN
Conversion Table
To convert from: To: Multiply By: To convert from: To: Multiply By:
Length Velocity
Feet (ft) meters (m) 0,30481 Feet per minute (ft/min) meters per second (m/s) 0,00508
Inche (in) milimeters (mm) 25,4 Feet per second (ft/s) meters per second (m/s) 0,3048
Area Energy, Power and Capacity

2 2
Square feet (ft ) square meters(m ) 0,93 British Termal Units (BTU) Kilowatt (kW) 0,000293
2 2
Square inche(in ) square milimeters(mm ) 645,2 British Termal Units (BTU) Kilocalorie (kcal) 0,252
Tons (refrig. Effect) Kilowatt (kW) 3,516
Volume Tons (refrig. Effect) Kilocalorie per hour (kcal/h 3024
3 3
Cubic feet (ft ) cubic meters(m ) 0,0283 Horsepower (HP) Kilowatt (kW) 0,7457
3 3
Cubic Inches (in ) cubic milimeters (mm ) 16387
Gallons (gal) litres (L) 3,785
3
Gallons (gal) cubic meters (m ) 0,003785 Pressão
Feet of water (ft.H2O) Pascal (Pa) 2990
Flow Inches os water (in.H2O) Pascal (Pa) 249
3
Cubic feet / min (cfm) cubic meters / second (m /s) 0,000472 Pounds per square inch (PSI) Pascal (Pa) 6895
3 2 -2
Cubic feet / min (cfm) cubic meters / hour (m /h) 1,69884 Pounds per square inch (PSI) Bar ou kg/cm 6,895 x 10
3
Gallons / min (GPM) cubic meters / hour (m /h) 0,2271
Gallons / min (GPM) litres / second (L/s) 0,06308 Peso
Ounces (oz) Kilograms (kg) 0,02835
Pounds (lbs) Kilograms (kg) 0,4536
Te m p e r at ur e Te m p e r at u r e Te m p e r at u r e Te m p e r at u r e Te m p e r at u r e
°C C ou F °F °C C ou F °F °C C ou F °F °C C ou F °F °C C ou F °F
-40,0 -40 -40 -15,0 5 41 10,0 50 122 35,0 95 203 60,0 1 40 284
-39,4 -39 -38,2 -14,4 6 42,8 10,6 51 123,8 35,6 96 204,8 60,6 1 41 285,8
-38,9 -38 -36,4 -13,9 7 44,6 11,1 52 125,6 36,1 97 206,6 61,1 1 42 287,6
-38,3 -37 -34,6 -13,3 8 46,4 11,7 53 127,4 36,7 98 208,4 61,7 1 43 289,4
-37,8 -36 -32,8 -12,8 9 48,2 12,2 54 129,2 37,2 99 210,2 62,2 1 44 291,2
-37,2 -35 -31 -12,2 10 50 12,8 55 131 37,8 10 0 212 62,8 1 45 293
-36,7 -34 -29,2 -11,7 11 51,8 13,3 56 132,8 38,3 10 1 213,8 63,3 1 46 294,8
-36,1 -33 -27,4 -11,1 12 53,6 13,9 57 134,6 38,9 10 2 215,6 63,9 1 47 296,6
-35,6 -32 -25,6 -10,6 13 55,4 14,4 58 136,4 39,4 10 3 217,4 64,4 1 48 298,4
-35,0 -31 -23,8 -10,0 14 57,2 15,0 59 138,2 40,0 10 4 219,2 65,0 1 49 300,2
-34,4 -30 -22 -9,4 15 59 15,6 60 140 40,6 10 5 221 65,6 1 50 302
-33,9 -29 -20,2 -8,9 16 60,8 16,1 61 141,8 41,1 10 6 222,8 66,1 1 51 303,8
-33,3 -28 -18,4 -8,3 17 62,6 16,7 62 143,6 41,7 10 7 224,6 66,7 1 52 305,6
-32,8 -27 -16,6 -7,8 18 64,4 17,2 63 145,4 42,2 10 8 226,4 67,2 1 53 307,4
-32,2 -26 -14,8 -7,2 19 66,2 17,8 64 147,2 42,8 10 9 228,2 67,8 1 54 309,2
-31,7 -25 -13 -6,7 20 68 18,3 65 149 43,3 11 0 230 68,3 1 55 311
-31,1 -24 -11,2 -6,1 21 69,8 18,9 66 150,8 43,9 11 1 231,8 68,9 1 56 312,8
-30,6 -23 -9,4 -5,6 22 71,6 19,4 67 152,6 44,4 11 2 233,6 69,4 1 57 314,6
-30,0 -22 -7,6 -5,0 23 73,4 20,0 68 154,4 45,0 11 3 235,4 70,0 1 58 316,4
-29,4 -21 -5,8 -4,4 24 75,2 20,6 69 156,2 45,6 11 4 237,2 70,6 1 59 318,2
-28,9 -20 -4 -3,9 25 77 21,1 70 158 46,1 11 5 239 71,1 1 60 320
-28,3 -19 -2,2 -3,3 26 78,8 21,7 71 159,8 46,7 11 6 240,8 71,7 1 61 321,8
-27,8 -18 -0,4 -2,8 27 80,6 22,2 72 161,6 47,2 11 7 242,6 72,2 1 62 323,6
-27,2 -17 1,4 -2,2 28 82,4 22,8 73 163,4 47,8 11 8 244,4 72,8 1 63 325,4
-26,7 -16 3,2 -1,7 29 84,2 23,3 74 165,2 48,3 11 9 246,2 73,3 1 64 327,2
-26,1 -15 5 -1,1 30 86 23,9 75 167 48,9 12 0 248 73,9 1 65 329
-25,6 -14 6,8 -0,6 31 87,8 24,4 76 168,8 49,4 12 1 249,8 74,4 1 66 330,8
-25,0 -13 8,6 0,0 32 89,6 25,0 77 170,6 50,0 12 2 251,6 75,0 1 67 332,6
-24,4 -12 10,4 0,6 33 91,4 25,6 78 172,4 50,6 12 3 253,4 75,6 1 68 334,4
-23,9 -11 12,2 1,1 34 93,2 26,1 79 174,2 51,1 12 4 255,2 76,1 1 69 336,2
-23,3 -10 14 1,7 35 95 26,7 80 176 51,7 12 5 257 76,7 1 70 338
-22,8 -9 15,8 2,2 36 96,8 27,2 81 177,8 52,2 12 6 258,8 77,2 1 71 339,8
-22,2 -8 17,6 2,8 37 98,6 27,8 82 179,6 52,8 12 7 260,6 77,8 1 72 341,6
-21,7 -7 19,4 3,3 38 100,4 28,3 83 181,4 53,3 12 8 262,4 78,3 1 73 343,4
-21,1 -6 21,2 3,9 39 102,2 28,9 84 183,2 53,9 12 9 264,2 78,9 1 74 345,2
-20,6 -5 23 4,4 40 104 29,4 85 185 54,4 13 0 266 79,4 1 75 347
-20,0 -4 24,8 5,0 41 105,8 30,0 86 186,8 55,0 13 1 267,8 80,0 1 76 348,8
-19,4 -3 26,6 5,6 42 107,6 30,6 87 188,6 55,6 13 2 269,6 80,6 1 77 350,6
-18,9 -2 28,4 6,1 43 109,4 31,1 88 190,4 56,1 13 3 271,4 81,1 1 78 352,4
-18,3 -1 30,2 6,7 44 111,2 31,7 89 192,2 56,7 13 4 273,2 81,7 1 79 354,2
-17,8 0 32 7,2 45 113 32,2 90 194 57,2 13 5 275 82,2 1 80 356
-17,2 1 33,8 7,8 46 114,8 32,8 91 195,8 57,8 13 6 276,8 82,8 1 81 357,8
-16,7 2 35,6 8,3 47 116,6 33,3 92 197,6 58,3 13 7 278,6 83,3 1 82 359,6
-16,1 3 37,4 8,9 48 118,4 33,9 93 199,4 58,9 13 8 280,4 83,9 1 83 361,4
-15,6 4 39,2 9,4 49 120,2 34,4 94 201,2 59,4 13 9 282,2 84,4 1 84 363,2
CG-PRC002E-EN 37
Trane optimizes the performance of homes and buildings around the world. A business of Ingersoll Rand, the leader in creating and
sustaining safe, comfortable and energy efficient environments, Trane offers a broad portfolio of advanced controls and HVAC
systems, comprehensive building services, and parts. For more information, visit www.trane.com.br
Trane has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.
© 2012 Trane Produced with paper that uses fewer

All rights reserved trees and chemicals, less energy, and
CG-PRC002E-EN July 2012 environmentally friendly print practices that
Supersedes CG-PRC002D-EN September 2009 reduce waste.

Cg-Prc002e-En 0712

Uploaded by

Copyright:

Available Formats

Cg-Prc002e-En 0712

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cg-Prc002e-En 0712

Uploaded by

Copyright:

Available Formats

Product Catalogue

CGAD Liquid Chillers

CGAD020 CGAD040 CGAD070 CGAD100

July 2012 CG-PRC002E-EN

Performance Adjustment Factors 9

Acustic Pressure Levels 16

Digits 1, 2 - Unit Model Digit 15 - Evaporator Application Digit 25 - Protection panels

Digit 3 - Unit Type Digit 16 - Coil Type Digit 26 - Installation accessories

Digit 14 - Expansion Valve type

Tab. 01 - General Data - CGAD 20-90 TR - 50 or 60 Hz

Liquid chiller capacity on table of Selection example: For example:

Fig. 01 - Evaporator hydraulic piping components

Fig. 02 - Evaporator Pressure Drop - 20 to 60 Tons Units

Load loss (Ft. of water)

From: To: Multiplier:

Gallons/min (GPM) L/s 0,06308

Evaporator Water Flow (GPM)

Fig. 03 - Evaporator Pressure Drop - 70 to 90 Tons Units

Load loss (kPa)

Evaporator Water Flow (GPM)

Fig. 04 - Evaporator Pressure Drop - 100 to 120 Tons Units

De: Para: Multiplicador:

Galões/min (GPM) L/s 0,06308

Fig. 05 - Evaporator Pressure Drop - 150 Tons Units

Flow GPM Flow GPM

% of Ethylene Glycol in Weight % de Propylene Glycol in Weight

Altitude Capacity Consum ption Water Flow

2500 0,983 1,067 0,983

Temp. de entrada ar condensador (ºC)

Condenser entering Air Temperature (ºC)

Condenser entering Air Temperature (ºC)

Tab. 03d -Performance Data - R- 22 (TSA = 7ºC)

Condenser entering Air Temperature (ºC)

Condenser entering Air Temperature (ºC)

Condenser entering Air Temperature (ºC)

Tab. 04d - Performance Data - R- 407C (TSA = 7ºC)

Condenser entering Air Temperature (ºC)

Condenser entering Air Temperature (ºC)

Condenser entering Air Temperature (ºC)

Tab. 05d -Performance Data - R- 22 (TSA = 7ºC)

Condenser entering Air Temperature (ºC)

Condenser entering Air Temperature (ºC)

Condenser entering Air Temperature (ºC)

Tab. 06d - Performance Data - R- 407C (TSA = 7ºC)

Tab. 07 - Cooled liquid CGAD series.

Equipment Acustic Pressure (dbA) of 10 meters

The owner of an establishment or building

Tab. 08 - Electrical Data - 60 Hz

Tab. 09 - Electrical Data - 50 Hz

Fig. 09 - Unit Dimensions - CGAD 020

AIR FLOW QUADRO ELÉTRICO AIR FLOW

Fig. 10 - Maintenance and air circulation clearances

Fig.11 - Unit Dimensions - CGAD 025

DIMENSÕES DA UNIDADE CGAD 025

2000 1700 CHILLED WATER INTLET

Fig. 12 - Maintenance and air circulation clearances

Fig.13 - Unit Dimensions - CGAD 030

Fig. 14 - Maintenance and air circulation clearances

Fig. 15 - Unit Dimensions - CGAD 040