J A PA N E S E

INDUSTRIAL
STANDARD
Translated and Published by
Japanese Standards Association

JIS G 3193 : 2019

(JISF)
Dimensions, shape, mass and
permissible variations of hot rolled
steel plates, sheets and strips

ICS 77.140.70;77.140.50
Reference number : JIS G 3193 : 2019 (E)

PROTECTED BY COPYRIGHT 11 S
G 3193 : 2019

Date of Establishment: 1954-07-30

Date of Revision: 2019-06-20
Date of Public Notice in Official Gazette: 2019-06-20
Investigated by: Japanese Industrial Standards Committee
Standards Board for ISO area
Technical Committee on Metal and Inorganic
Materials

JIS G 3193 : 2019, First English edition published in 2020-02

Translated and published by: Japanese Standards Association

Mita MT Building, 3-13-12, Mita, Minato-ku, Tokyo, 108-0073 JAPAN

In the event of any doubts arising as to the contents,

the original JIS is to be the final authority.

© JSA 2020
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or
utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.

Printed in Japan
AT

PROTECTED BY COPYRIGHT
 G 3193 : 2019

Contents

Page

Introduction ························································································································· 1
1 Scope ···························································································································· 1
2 Normative reference ·································································································· 1
3 Expression of dimensions ·························································································· 1
4 Standard dimensions ································································································· 2
5 Shape and dimensional tolerances ··········································································· 2
6 Mass··························································································································· 11
6.1 Mass of steel plates and sheets ·············································································· 11
6.2 Mass of steel strips ·································································································· 12
7 Appearance ··············································································································· 13
Annex JA (informative) Comparison table between JIS and corresponding
International Standard ························································· 14

(i)

PROTECTED BY COPYRIGHT
G 3193 : 2019

This Japanese Industrial Standard has been revised by the Minister of Economy, Trade
and Industry, through deliberations at the Japanese Industrial Standards Committee as
the result of proposal for revision of Japanese Industrial Standard submitted by The
Japan Iron and Steel Federation (JISF) with the draft being attached, based on the
provision of Article 12 Clause 1 of the Industrial Standardization Law applicable to the
case of revision by the provision of Article 14.
Consequently JIS G 3193 :2008 is replaced with this Standard.
This JIS document is protected by the Copyright Law.
Attention is drawn to the possibility that some parts of this Standard may conflict with
patent rights, applications for a patent after opening to the public or utility model rights.
The relevant Minister and the Japanese Industrial Standards Committee are not
responsible for identifying any of such patent rights, applications for a patent after
opening to the public or utility model rights.

(ii)

PROTECTED BY COPYRIGHT
JAPANESE INDUSTRIAL STANDARD JIS G 3193 : 2019

Dimensions, shape, mass and permissible

variations of hot rolled steel plates,
sheets and strips

Introduction
This Japanese Industrial Standard has been prepared based on ISO 7452:2013, Edi-
tion 3, with some modifications of the technical contents to reflect transactional prac-
tices.
The vertical lines on both sides and dotted underlines indicate changes from the cor-
responding International Standard. A list of modifications with the explanations is
given in Annex JA.

1 Scope
This Standard specifies requirements for the appearance and shapes of the hot rolled
steel plates, steel sheets (including cut lengths from steel strips), steel strips and their
permissible variations as well as the dimensions, mass and their tolerances. This Stan-
dard is not applicable to flat bars.
The application of this Standard is specified in the relevant product standards.
NOTE The International Standard corresponding to this Standard and the sym-
bol of degree of correspondence are as follows.
ISO 7452:2013 Hot-rolled steel plates—Tolerances on dimensions and shape
(MOD)
In addition, symbols which denote the degree of correspondence in the
contents between the relevant International Standards and JIS are IDT
(identical), MOD (modified), and NEQ (not equivalent) according to ISO/
IEC Guide 21-1.

2 Normative reference
The following standard contains provisions which, through reference in this text, con-
stitute provisions of this Standard. The most recent edition of the standard (including
amendments) indicated below shall be applied.
JIS Z 8401 Guide to the rounding of numbers
-------------------------------------------------------------------------------------

3 Expression of dimensions
The dimensions of steel plates, sheets and strips shall be expressed as follows.
a) The dimensions of steel plates and sheets shall be expressed by thickness, width and
----------------------------------------------------------------------------------------------------------------------------------------------------
length in millimetres.
----------------------------------------

b) The dimensions of steel strips shall be expressed by thickness and width in

----------------------------------------------------------------------------------------------------------------------------------------------------
millimetres.
----------------------

PROTECTED BY COPYRIGHT