QUICK START GUIDE

Running OcNOS® VMs

in GNS3 Quick Start Guide
June 2023

Contents
About the OcNOS VM............................................................................................................................................... 2
Benefits of the OcNOS VM................................................................................................................................................... 2

Feature List................................................................................................................................................................................ 2

Running OcNOS in GNS3.......................................................................................................................................... 3

System Requirements for Running OcNOS VMs in GNS3................................................................................ 3
Files Provided for Running OcNOS VMSs in GNS3............................................................................................ 4
Setup the GNS3 Environment for Testing BGP and L3 VPN............................................................................. 4
1. Install the Remote GNS3 Server VM in the VMware Hypervisor............................................................................ 4

2. Install and Configure GNS3 Client in your MacOS or Windows Laptop................................................................ 6

3. Import an Example GNS3 Project called BGP and L3 VPN on the Remote GNS3 VM........................................ 7

4. Verify BGP and L3 VPN Project.......................................................................................................................................10

References................................................................................................................................................................... 14
OcNOS.....................................................................................................................................................................................14

GNS3........................................................................................................................................................................................14

Appendix-A - Example BGP and L3 VPN Configuration Used in the GNS3 Environment....................... 15
CSR-1 Switch Configuration................................................................................................................................................15

AGGR-1 Switch Configuration............................................................................................................................................17

AGGR-2 Switch Configuration............................................................................................................................................19

CORE-1 Switch Configuration............................................................................................................................................21

AGGR-3 Switch Configuration............................................................................................................................................23

About the OcNOS VM
The OcNOS Virtual Machine (VM) from IP Infusion helps you get familiar with OcNOS. The OcNOS
VM runs on a standard x86 environment. The OcNOS VM is used to validate configurations and test
L2, L3, and MPLS features at your own pace, with no costs associated. Without bare metal switches,
OcNOS VM can be run on popular environments like GNS3 and hypervisors including KVM, VirtualBox,
and VMware. This document provides information on how to run OcNOS VM in the GNS3 environment.

All basic Layer 2, Layer 3, and multicast functionality are available. MPLS support is also available,
including limited support of MPLS forwarding. The OcNOS VM comes with a 365 days valid license.

The data plane forwarding functions have limited support. OcNOS VM is designed for feature testing,
and not for data plane performance testing or full bandwidth traffic testing.

Benefits of the OcNOS VM

Following are benefits of OcNOS VM:
• Free
• No need to wait for the hardware
• Get familiar with OcNOS software
• Validate configurations
• Test L2, L3, and MPLS features without any risk
• Prototype network operations

Feature List
CLIs for the following features are available. The complete feature set of OcNOS is supported on
Commercial off-the-shelf (COTS) hardware platforms switches from Dell, Delta Agema, Edgecore,
and UFISpace. For the complete feature list, please contact IP Infusion Sales.

SYSTEM FEATURES • VLAN Interface

• ARP support • QinQ
• SSH/Telnet • 802.1x
• SNMP
LAYER-3 FEATURES
• Debugging and logging
• IPv4 Routing
• AAA
• VRF Support
• DHCP, DNS
• RIP v2, RIP NG
LAYER-2 FEATURES • BFD with BGP, OSPF, ISIS
• STP/RSTP/MSTP • BGP
• BPDU Guard and Root Guard • OSPF v2, OSPF v3
• VLAN, Private VLAN • ISIS
• LACP • VRRP
• LLDP

2 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

MPLS FEATURES • BGP MPLS L3VPN
• MPLS Label Switching • MPLS DCI using ICCP and VPLS redundancy
• LDP and RSVP Support
MULTICAST FEATURES
• RSVP FRR
• IGMP
• VPLS with LDP Signaling
• PIM-SM/SSM/DM
• VPWS with 1:1 backup support
• MSDP Support

Running OcNOS in GNS3

This section describes how to install GNS3 in VMware hypervisor and run OcNOS VM switches
and test servers in GNS3 environment. We will create following switch topology shown below to
test OcNOS L2 and L3 software features. In this example, we will test the BGP and L3 VPN feature.
The following is a test topology in a GNS3 environment.

core
Aggregation
PE

One Cell Site Router (CSR), three Aggregation Routers (AGGR) and a core router are used in this GNS3
test topology. Two Debian Linux servers are used in GNS3 for generating the test traffic.

System Requirements for Running OcNOS VMs in GNS3

Following system requirements are used for running OcNOS VMs in GNS3. We will run GNS3 as a
remote server VM in the VMware hypervisor. Following are requirements for running a remote GNS3
server VM:
• VMware vSphere Hypervisor (ESXi) 6.5.0 or later
• VM requirements:
– CPU: 2 vCPUs. CPU need to support the nested VM in the ESXi server for running GNS3.
Please refer to the next section for details
– Memory: 16 GB
– Hard Disk: 40 GB
– NICs: 1. Make sure there is a DHCP server on the network this NIC card is connected to

• We will be using GNS3 project image that contains the following VMs: five OcNOS VMs (version
6.3.0 Build 126) with BGP and L3 VPN configuration, and 2 Debian Linux Servers.

3 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

Files Provided for Running OcNOS VMs in GNS3
Following files are provided for running OcNOS VMs in GNS3:
1. BGP-L3VPN-Proj.gns3project file includes OcNOS VM image, OcNOS VM GNS3 Template and
includes configuration for all switches and servers for BGP and L3 VPN test case. Use this file to
populate BGP and L3 VPN topology and test in the GNS3 environment. It will get you up and
running quickly. This is the only file you need for the above purpose.
2. Alternatively, if you want to create your own topology in GNS3 and test, use the following two files:
a. OcNOS-SP-MPLS-x86-6.3.0-126-GA.vmdk.xz: This is OcNOS VM image for the GNS3
environment. OcNOS VM image file is archive compressed using XZ compression. Use Mac OS
Archive Utility or 7-zip tools to uncompress the file. To uncompress the file in Linux, use the
command xz -d <file_name>.xz
b. OCNOS.gns3a: This is OcNOS QEMU VM Template. You can import this template to create
OcNOS VMs in GNS3.

Setup the GNS3 Environment for Validating BGP and L3 VPN

Setting up above topology in GNS3 for validating BGP and L3 VPN requires the following four steps:
1. Install the remote GNS3 server VM in the VMware hypervisor
2. Install and configure GNS3 client in your MacOS or Windows laptop
3. Import an example GNS3 Project called BGP and L3 VPN Project on the remote GNS3 VM
4. Verify BGP and L3 VPN Project

1. Install the Remote GNS3 Server VM in the VMware vSphere Hypervisor

The following are steps to install a GNS3 VM in a VMware vSphere hypervisor:
a. Download GNS3 VM to run in VMware vSphere ESXi hypervisor. In this example GSN3 VM
version 2.2.35.1 and VMware ESXi version 7.0.3 are used for testing.
b. Install the GNS3 VM on the ESXi server: Follow the documentation given in this link to install GNS3.
After you install the GNS3 VM, turn off the VM power, select edit settings and expand CPU to
check the nested VM support in the ESXi server. Hardware Virtualization needs to be enabled
in this case as shown below. Set the CPU to 2.

4 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

 In addition set the Memory of the VM to 16 GB and click Save. VM takes up 18Gb of hard disk space.
c. Power up the VM and click OK on the VM console as shown below.

The GNS3 VM gets its IP address 10.10.25.127 and TCP port 80 in this example from the DHCP
server and the IP address is displayed on the console. The credentials for login are also given in
the console: username is gns3 and password is gns3. The Web URL to access the GNS
environment is given as http://10.10.25.127.

5 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

2. Install and Configure GNS3 Client
Following are steps to install and configure GNS3 client on your laptop and setup a GNS3 environment
for testing OcNOS features:
To install GNS3 client on your laptop, follow the instructions provided below:
a. Install GNS3 client on the laptop: Use the following link for MacOS: Install GNS3 client on a
Mac OS X laptop. In this example GNS3 client version 2.2.35.1 is used. Please note GNS3
server version need to match with GNS3 client version. Use the following link for Windows:
Install GNS3 client on a Windows laptop.
b. Run GNS3 client application on your laptop.
c. Configure the GNS3 server in the GNS3 Application as follows. Select GNS3->Preferences and select
Main server tab enter GNS server parameters as shown below (use GNS3 VM info) and click Apply
and OK. Please note: Enable local server should not be selected.
d.

Verify the Main server configuration.

Select Server Summary tab, you will see the Main Server running with green color status.

6 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

3. Import an Example GNS3 Project Called BGP and L3 VPN on the Remote GNS3 VM
BGP-L3 VPN project file BGP-L3VPN-Proj.gns3project includes OcNOS VM image, OcNOS VM GNS3
Template and includes configuration for all switches and servers for BGP and L3 VPN test case.
For future use you can feel free to change the topology or change configuration in any of the
OcNOS switches.
Download the BGP-L3VPN.gns3project file to your laptop from the IP Infusion website.
Select File > Import portable project menu and select the gns3 project file you have downloaded
earlier and give it a project name as shown below:

Click OK. Press Play button at the top to start all devices in GNS3 project.

7 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

Once all devices are up you will see the following the following screen with all ports in green status:

Please note: Management IP addresses for your OcNOS switches will be different than the ones given
in the above screen. You need to edit the above screen to change Management IP addresses. To get
the Management IP address of a specific switch, please use the info provided in the section. To edit the
screen to change the Management IP address, click the Pencil Icon at the top menu.

GET FAMILIAR WITH ACCESSING SERVERS AND SWITCHES:

a. To access the server console, right click on the server and select console.

8 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

 Following are default credentials to log into the Debian Server: debian/debian
From the server Linux CLI prompt you can run CLI commands to generate test traffic.
b. To access any specific switch console, right click on that switch, and select console similar
to the above step.
Following are default credentials to log into the console of any of the OcNOS
switches: ocnos/ocnos

Now on you can SSH to the switch using the following command from your laptop CLI:
ssh [email protected] and enter password as ocnos. You can use SSH session for running
verification commands listed in later section.

9 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

4. Verify BGP and L3 VPN Project
We will run several commands to verify BGP and L3 VPN functionalities.
a. Generate Test Traffic: Log into the console of the Debian11.2-1 Server from the GNS3 client
Application (by right clicking on the server and choose Console) and execute the following Linux
shell command to send 1000 packets from the Debian11.2-1 Server to the Debian11.2-2 Server
on the TEST_VRF.

debian@debian:~$ ping -c 1000 -i 1 40.1.1.200

PING 40.1.1.200 (40.1.1.200) 56(84) bytes of data.
64 bytes from 40.1.1.200: icmp_seq=1 ttl=63 time=4.15 ms
64 bytes from 40.1.1.200: icmp_seq=2 ttl=63 time=4.84 ms
64 bytes from 40.1.1.200: icmp_seq=3 ttl=63 time=5.45 ms
64 bytes from 40.1.1.200: icmp_seq=4 ttl=63 time=3.56 ms
64 bytes from 40.1.1.200: icmp_seq=5 ttl=63 time=3.63 ms
…
b. Check summary of known neighbor: Log into the console of the CSR-1 OcNOS virtual switch (or
SSH into CSR-1) and run the following commands to verify the BGP and L3 VPN functionalities.
The show clns neighbors command provides a summary of known neighbors, the connecting
interface, and the state of the adjacency.

CSR-1#show clns neighbors

Total number of L1 adjacencies: 2

Total number of L2 adjacencies: 0
Total number of adjacencies: 2
Tag 1: VRF : default
System Id Interface SNPA State Holdtime Type Protocol
AGGR-1 eth2 0cc6.74db.0001 Up 6 L1 IS-IS
AGGR-2 eth3 0c2c.0e08.0001 Up 27 L1 IS-IS

c. Check TEST_VRF forwarding table: Following output shows we have path to reach the second server.

CSR-1# show mpls vrf-forwarding-table vrf TEST_VRF

Owner FEC FTN-ID Oper-Status Out-Label Tunnel-id NHLFE-id Out-Intf. Nexthop
BGP 40.1.1.0/24 1 Up 25600 0 5 eth2 10.1.1.5

10 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

 Also check Incoming Label Map entries. Use the following command to view Incoming label
mapping (ILM) table entries

CSR-1#show mpls ilm-table

Codes: > - installed ILM, * - selected ILM, p - stale ILM
K - CLI ILM, T - MPLS-TP, s - Stitched ILM
S - SNMP, L - LDP, R - RSVP, C - CRLDP
B - BGP , K - CLI , V - LDP_VC, I - IGP_SHORTCUT
O - OSPF/OSPF6 SR, i - ISIS SR, k - SR CLI
P - SR Policy, U - unknown

Code FEC/VRF/L2CKT ILM-ID In-Label Out-Label In-Intf Out-Intf/VRF Nexthop

LSP-Type
L> 10.1.1.106/31 11 24965 3 N/A eth3 10.1.1.103 LSP_DEFAULT
L> 10.1.1.3/32 7 24961 3 N/A eth3 10.1.1.103 LSP_DEFAULT
B> TEST_VRF 1 24320 Nolabel N/A TEST_VRF N/A LSP_DEFAULT
L> 10.1.1.2/32 13 24967 3 N/A eth2 10.1.1.101 LSP_DEFAULT
L> 10.1.1.104/31 14 24968 3 N/A eth2 10.1.1.101 LSP_DEFAULT

d. Check for path to AGGR-3 in MPLS forwarding Table: Run the following command in CSR-1.

CSR-1#show mpls forwarding-table

Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN

Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
L> 10.1.1.2/32 1 32 - Yes LSP_DEFAULT 3 eth2 No
10.1.1.101
L> 10.1.1.3/32 2 14 - Yes LSP_DEFAULT 3 eth3 No
10.1.1.103
L> 10.1.1.4/32 3 16 - Yes LSP_DEFAULT 24962 eth3 No
10.1.1.103
48 - Yes LSP_DEFAULT 24962 eth2 No
10.1.1.101
L> 10.1.1.5/32 4 20 - Yes LSP_DEFAULT 24963 eth3 No
10.1.1.103
49 - Yes LSP_DEFAULT 24963 eth2 No
10.1.1.101
L> 10.1.1.104/31 5 32 - Yes LSP_DEFAULT 3 eth2 No
10.1.1.101
L> 10.1.1.106/31 6 14 - Yes LSP_DEFAULT 3 eth3 No
10.1.1.103
L> 10.1.1.108/31 7 28 - Yes LSP_DEFAULT 24965 eth3 No
10.1.1.103
50 - Yes LSP_DEFAULT 24966 eth2 No 10.1.1.101

You can see AGGR-5 can be reached via eth2 and eth3.

11 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

 e. Check LDP sessions in CSR-1: Execute the following CLI in CSR-1.

CSR-1#show ldp session

Peer IP Address IF Name My Role State KeepAlive UpTime
10.1.1.2 eth2 Passive OPERATIONAL 30 22:24:09
10.1.1.3 eth3 Passive OPERATIONAL 30 22:24:09

f. Check route between two Debian Servers: Check the route from one Debian Server to other
using the following command:
One server is directly connected to 30.1.1.0/24 network and other server in 40.1.1.0/24
network is accessible via BGP.

CSR-1#show ip route vrf TEST_VRF database

Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP
O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2,
ia - IS-IS inter area, E - EVPN,
v - vrf leaked
> - selected route, * - FIB route, p - stale info

IP Route Table for VRF “TEST_VRF”

C *> 30.1.1.0/24 is directly connected, eth1, 1d07h49m
B *> 40.1.1.0/24 [200/0] via 10.1.1.5, 00:20:26

Gateway of last resort is not set

g. Check L3VPN routes: Use the following command to display information relating to MPLS VPN.

CSR-1#show ip bgp vpnv4 all summary

BGP router identifier 10.1.1.1, local AS number 65000
BGP table version is 9
1 BGP AS-PATH entries
0 BGP community entries

Neighbor V AS MsgRcv MsgSen TblVer InQ OutQ Up/Down State/PfxRcd

10.1.1.2 4 65000 4446 4444 9 0 0 00:20:32 1
10.1.1.3 4 65000 4420 4418 9 0q 0 00:20:37 1

Total number of neighbors 2

Total number of Established sessions 2

h. Stop flow of traffic between CSR-1 and AGGR-1 and verify whether traffic flows from one
server to the other:
When the ICMP traffic is flowing, right click on the link between the CSR-1 and the AGGR-1.
Select Suspend to stop the traffic flowing through that link as shown below. Now traffic will not
go through eth2 interface. Traffic will only go through eth3 interface.

12 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

 Check the traffic flow using the following command in CSR-1.
CSR-1#show mpls forwarding-table
Codes: > - installed FTN, * - selected FTN, p - stale FTN,
B - BGP FTN, K - CLI FTN, t - tunnel, P - SR Policy FTN,
L - LDP FTN, R - RSVP-TE FTN, S - SNMP FTN, I - IGP-Shortcut,
U - unknown FTN, O - SR-OSPF FTN, i - SR-ISIS FTN, k - SR-CLI FTN

Code FEC FTN-ID Nhlfe-ID Tunnel-id Pri LSP-Type Out-Label Out-Intf ELC Nexthop
L> 10.1.1.2/32 1 10 - Yes LSP_DEFAULT 24961 eth3 No
10.1.1.103
L> 10.1.1.3/32 2 14 - Yes LSP_DEFAULT 3 eth3 No
10.1.1.103
L> 10.1.1.4/32 3 16 - Yes LSP_DEFAULT 24962 eth3 No
10.1.1.103
L> 10.1.1.5/32 4 20 - Yes LSP_DEFAULT 24963 eth3 No
10.1.1.103
L> 10.1.1.104/31 5 27 - Yes LSP_DEFAULT 24964 eth3 No
10.1.1.103
L> 10.1.1.106/31 6 14 - Yes LSP_DEFAULT 3 eth3 No
10.1.1.103
L> 10.1.1.108/31 7 28 - Yes LSP_DEFAULT 24965 eth3 No
10.1.1.103

13 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

 i. Verify whether traffic can reach AGGR-3 with MPLS ping:

CSR-1#ping mpls ldp 10.1.1.5/32 detail

Sending 5 MPLS Echos to 10.1.1.5, timeout is 5 seconds

Codes:
‘!’ - Success, ‘Q’ - request not sent, ‘.’ - timeout,
‘x’ - Retcode 0, ‘M’ - Malformed Request, ‘m’ - Errored TLV,
‘N’ - LBL Mapping Err, ‘D’ - DS Mismatch,
‘U’ - Unknown Interface, ‘R’ - Transit (LBL Switched),
‘B’ - IP Forwarded, ‘F’ No FEC Found, ‘f’ - FEC Mismatch,
‘P’ - Protocol Error, ‘X’ - Unknown code,
‘Z’ - Reverse FEC Validation Failed

Type ‘Ctrl+C’ to abort

! seq_num = 1 10.1.1.109 1.92 ms

! seq_num = 2 10.1.1.109 1.01 ms
! seq_num = 3 10.1.1.109 1.26 ms
! seq_num = 4 10.1.1.109 1.63 ms
! seq_num = 5 10.1.1.109 2.52 ms

Success Rate is 100.00 percent (5/5)

round-trip min/avg/max = 1.01/1.77/2.52

References
OcNOS
The following are reference materials related to OcNOS:
• OcNOS Configuration Guides

GNS3
The following are reference materials related to GNS3:
• Getting Started with GNS3

14 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

Appendix-A: Example BGP and L3 VPN Configuration
Used in the GNS3 Environment
The following example configurations are used in the GNS3 environment to test BGP and L3 VPN
functionality in OcNOS virtual switches.

CSR-1 Switch Configuration

The configuration used in the CSR-1 OcNOS virtual switch is given below:

!
no service password-encryption
!
logging console 2
logging monitor 7
logging cli
!
ip vrf management
!
ip vrf TEST_VRF
rd 10.1.1.1:1
route-target both 65000:1
!
hostname CSR-1
ip domain-lookup
feature telnet
feature ssh
feature rsyslog
!
router ldp
router-id 10.1.1.1
transport-address ipv4 10.1.1.1
!
!
interface lo
ip address 127.0.0.1/8
ip address 10.1.1.1/32 secondary
ipv6 address ::1/128
ip router isis 1
!
interface eth0
ip vrf forwarding management
ip address dhcp
!
interface eth1
ip vrf forwarding TEST_VRF
ip address 30.1.1.1/24
!
interface eth2
ip address 10.1.1.100/31
label-switching
mpls ldp-igp sync isis level-1

15 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

 isis network point-to-point
ip router isis 1
enable-ldp ipv4
lldp-agent
set lldp enable txrx
exit
!
interface eth3
ip address 10.1.1.102/31
label-switching
mpls ldp-igp sync isis level-1
isis network point-to-point
ip router isis 1
enable-ldp ipv4
lldp-agent
set lldp enable txrx
exit
!
interface eth4
!
exit
!
router isis 1
is-type level-1
metric-style wide level-1
mpls traffic-eng router-id 10.1.1.1
mpls traffic-eng level-1
capability cspf
dynamic-hostname
bfd all-interfaces
net 49.0111.1100.0075.0001.00

!
router bgp 65000
bgp router-id 10.1.1.1
neighbor 10.1.1.2 remote-as 65000
neighbor 10.1.1.3 remote-as 65000
neighbor 10.1.1.2 update-source lo
neighbor 10.1.1.3 update-source lo
!
address-family vpnv4 unicast
neighbor 10.1.1.2 activate
neighbor 10.1.1.3 activate
exit-address-family
!
address-family ipv4 vrf TEST_VRF
redistribute connected
exit-address-family
!
line vty 0
exec-timeout 0 0
!
!
end

16 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

AGGR-1 Switch Configuration
The configuration used in the AGGR-1 OcNOS virtual switch is given below:

!
no service password-encryption
!
logging console 2
logging monitor 7
logging cli
!
ip vrf management
!
hostname AGGR-1
no ip domain-lookup
ip domain-lookup vrf management
feature telnet vrf management
feature ssh vrf management
feature rsyslog vrf management
!
router ldp
router-id 10.1.1.2
transport-address ipv4 10.1.1.2
!
!
interface lo
ip address 127.0.0.1/8
ip address 10.1.1.2/32 secondary
ipv6 address ::1/128
ip router isis 1
!
interface eth0
ip vrf forwarding management
ip address dhcp
!
interface eth1
ip address 10.1.1.101/31
label-switching
mpls ldp-igp sync isis level-1
isis network point-to-point
ip router isis 1
enable-ldp ipv4
lldp-agent
set lldp enable txrx
exit
!
interface eth2
ip address 10.1.1.104/31
label-switching
mpls ldp-igp sync isis level-1
isis network point-to-point
ip router isis 1
enable-ldp ipv4
lldp-agent

17 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

 set lldp enable txrx
exit
!
interface eth3
!
interface eth4
!
exit
!
router isis 1
is-type level-1
metric-style wide level-1
mpls traffic-eng router-id 10.1.1.2
mpls traffic-eng level-1
capability cspf
dynamic-hostname
bfd all-interfaces
net 49.0111.1100.0075.0002.00
!
router bgp 65000
no bgp inbound-route-filter
bgp router-id 10.1.1.2
neighbor 10.1.1.1 remote-as 65000
neighbor 10.1.1.3 remote-as 65000
neighbor 10.1.1.4 remote-as 65000
neighbor 10.1.1.5 remote-as 65000
neighbor 10.1.1.1 update-source lo
neighbor 10.1.1.3 update-source lo
neighbor 10.1.1.4 update-source lo
neighbor 10.1.1.5 update-source lo
!
address-family vpnv4 unicast
neighbor 10.1.1.1 activate
neighbor 10.1.1.1 route-reflector-client
neighbor 10.1.1.3 activate
neighbor 10.1.1.4 activate
neighbor 10.1.1.4 route-reflector-client
neighbor 10.1.1.5 activate
neighbor 10.1.1.5 route-reflector-client
exit-address-family
!
line vty 0
exec-timeout 0 0
!
!
end

18 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

AGGR-2 Switch Configuration
The configuration used in the AGGR-2 OcNOS virtual switch is given below:

!
no service password-encryption
!
logging console 2
logging monitor 7
logging cli
!
ip vrf management
!
hostname AGGR-2
no ip domain-lookup
ip domain-lookup vrf management
feature telnet vrf management
feature ssh vrf management
feature rsyslog vrf management
!
router ldp
router-id 10.1.1.3
transport-address ipv4 10.1.1.3
!
!
interface lo
ip address 127.0.0.1/8
ip address 10.1.1.3/32 secondary
ipv6 address ::1/128
ip router isis 1
!
interface eth0
ip vrf forwarding management
ip address dhcp
!
interface eth1
ip address 10.1.1.103/31
label-switching
mpls ldp-igp sync isis level-1
isis network point-to-point
ip router isis 1
enable-ldp ipv4
lldp-agent
set lldp enable txrx
exit
!
interface eth2
ip address 10.1.1.106/31
label-switching
mpls ldp-igp sync isis level-1
isis network point-to-point
ip router isis 1
enable-ldp ipv4
lldp-agent

19 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

 set lldp enable txrx
exit
!
interface eth3
!
interface eth4
!
exit
!
router isis 1
is-type level-1
metric-style wide level-1
mpls traffic-eng router-id 10.1.1.3
mpls traffic-eng level-1
capability cspf
dynamic-hostname
bfd all-interfaces
net 49.0111.1100.0075.0003.00
!
router bgp 65000
bgp router-id 10.1.1.3
no bgp inbound-route-filter
neighbor 10.1.1.1 remote-as 65000
neighbor 10.1.1.2 remote-as 65000
neighbor 10.1.1.4 remote-as 65000
neighbor 10.1.1.5 remote-as 65000
neighbor 10.1.1.1 update-source lo
neighbor 10.1.1.2 update-source lo
neighbor 10.1.1.4 update-source lo
neighbor 10.1.1.5 update-source lo
!
address-family vpnv4 unicast
neighbor 10.1.1.1 activate
neighbor 10.1.1.1 route-reflector-client
neighbor 10.1.1.2 activate
neighbor 10.1.1.2 route-reflector-client
neighbor 10.1.1.4 activate
neighbor 10.1.1.4 route-reflector-client
neighbor 10.1.1.5 activate
neighbor 10.1.1.5 route-reflector-client
exit-address-family
!
line vty 0
exec-timeout 0 0
!
!
end

20 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

CORE-1 Switch Configuration
The configuration used in the CORE-1 OcNOS virtual switch is given below:

no service password-encryption
!
logging console 2
logging monitor 7
logging cli
!
ip vrf management
!
hostname core-1
no ip domain-lookup
ip domain-lookup vrf management
feature telnet vrf management
feature ssh vrf management
feature rsyslog vrf management
!
router ldp
router-id 10.1.1.4
transport-address ipv4 10.1.1.4
!
interface lo
ip address 127.0.0.1/8
ip address 10.1.1.4/32 secondary
ipv6 address ::1/128
ip router isis 1
!
interface eth0
ip vrf forwarding management
ip address dhcp
!
interface eth1
ip address 10.1.1.108/31
label-switching
mpls ldp-igp sync isis level-1
isis network point-to-point
ip router isis 1
enable-ldp ipv4
lldp-agent
set lldp enable txrx
exit
!
interface eth2
ip address 10.1.1.105/31
label-switching
mpls ldp-igp sync isis level-1
isis network point-to-point
ip router isis 1
enable-ldp ipv4
lldp-agent
set lldp enable txrx
exit

21 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

!
interface eth3
ip address 10.1.1.107/31
label-switching
mpls ldp-igp sync isis level-1
ip router isis 1
enable-ldp ipv4
lldp-agent
set lldp enable txrx
exit
!
interface eth4
!
exit
!
router isis 1
is-type level-1
metric-style wide level-1
mpls traffic-eng router-id 10.1.1.4
mpls traffic-eng level-1
capability cspf
dynamic-hostname
bfd all-interfaces
net 49.0111.1100.0075.0004.00
!
router bgp 65000
bgp router-id 10.1.1.4
neighbor 10.1.1.2 remote-as 65000
neighbor 10.1.1.3 remote-as 65000
neighbor 10.1.1.5 remote-as 65000
neighbor 10.1.1.2 update-source lo
neighbor 10.1.1.3 update-source lo
neighbor 10.1.1.5 update-source lo
!
address-family vpnv4 unicast
neighbor 10.1.1.2 activate
neighbor 10.1.1.3 activate
neighbor 10.1.1.5 activate
exit-address-family
!
line vty 0
exec-timeout 0 0
!
!
end

22 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

AGGR-3 Switch Configuration
The configuration used in the AGGR-3 OcNOS virtual switch is given below:
!
no service password-encryption
!
logging console 2
logging monitor 7
logging cli
!
ip vrf management
!
ip vrf TEST_VRF
rd 10.1.1.5:1
route-target both 65000:1
!
hostname AGGR-3
ip domain-lookup
feature telnet
feature ssh
feature rsyslog
!
router ldp
router-id 10.1.1.5
transport-address ipv4 10.1.1.5
!
interface lo
ip address 127.0.0.1/8
ip address 10.1.1.5/32 secondary
ipv6 address ::1/128
ip router isis 1
!
interface eth0
ip vrf forwarding management
ip address dhcp
!
interface eth1
ip address 10.1.1.109/31
label-switching
mpls ldp-igp sync isis level-1
isis network point-to-point
ip router isis 1
enable-ldp ipv4
lldp-agent
set lldp enable txrx
exit
!
interface eth2
ip vrf forwarding TEST_VRF
ip address 40.1.1.1/24
lldp-agent
set lldp enable txrx
exit
!

23 | RUNNING OcNOS® VMS IN GNS3 QUICK START GUIDE

interface eth3
!
interface eth4
!
exit
!
router isis 1
is-type level-1
metric-style wide level-1
mpls traffic-eng router-id 10.1.1.5
mpls traffic-eng level-1
capability cspf
dynamic-hostname
bfd all-interfaces
net 49.0111.1100.0075.0005.00
!
router bgp 65000
bgp router-id 10.1.1.5
neighbor 10.1.1.1 remote-as 65000
neighbor 10.1.1.2 remote-as 65000
neighbor 10.1.1.3 remote-as 65000
neighbor 10.1.1.4 remote-as 65000
neighbor 10.1.1.1 update-source lo
neighbor 10.1.1.2 update-source lo
neighbor 10.1.1.3 update-source lo
neighbor 10.1.1.4 update-source lo
!
address-family vpnv4 unicast
neighbor 10.1.1.1 activate
neighbor 10.1.1.2 activate
neighbor 10.1.1.3 activate
neighbor 10.1.1.4 activate
exit-address-family
!
address-family ipv4 vrf TEST_VRF
redistribute connected
exit-address-family
!
line vty 0
exec-timeout 0 0
!
!
end

ABOUT IP INFUSION
IP Infusion is a leading provider of open network software and solutions for carriers, service providers and data center operators. Our solutions enable network operators to
disaggregate their networks to accelerate innovation, streamline operations, and reduce Total Cost of Ownership (TCO). Network OEMs may also disaggregate network devices
to expedite time to market, offer comprehensive services, and achieve carrier grade robustness. IP Infusion network software platforms have a proven track record in carrier-
grade open networking with over 500 customers and over 10,000 deployments. IP Infusion is headquartered in Santa Clara, Calif., and is a wholly owned and independently
operated subsidiary of ACCESS CO., LTD. Additional information can be found at http://www.ipinfusion.com

© 2023 IP Infusion, Inc. All rights reserved. IP Infusion is a registered trademark and the ipinfusion logo and OcNOS are trademarks of IP Infusion, Inc. All other trademarks
and logos are the property of their respective owners. IP Infusion assumes no responsibility for any inaccuracies in this document. IP Infusion reserves the right to change,
modify, transfer, or otherwise revise this publication without notice.

Phone | +1-877-699-3267 Email | [email protected] Web | www.ipinfusion.com