Operators manual

V 1.5 EN

Magnetic drilling machine

ECO.55S/TA

Serial number:

Date of purchase: / /

Don’t forget to register your machine at:

www.euroboor.com/register
[ only when registered you benefit from extended warranty ]
Congratulations on your purchase of the Euroboor ECO.55S/TA portable magnetic drilling machine.
Your model is designed to produce superior holes quickly and efficiently. Through years of
experience, constant innovation and development, Euroboor is committed to provide you with metal
cutting tools and products to help you be more productive.

Before operating your new magnetic drilling machine, please read all instructions first. These include
the Operators Manual and warning label on the unit itself. With proper use, car and maintenance
your model will provide you with years of effective hole drilling performance

TO REDUCE THE RISK OF INJURY USER MUST READ AND UNDERSTAND ALL INSTRUCTIONS

EUROBOOR BV
Kryptonstraat 110
2718TD Zoetermeer
Netherlands
T +31 79 361 49 90
F +31 79 361 49 89

[email protected]
www.euroboor.com

2
Table of contents

1. Safety 4
1.1 General safety instructions 4
1.2 Specific safety information 6
2. Description 7
2.1 Intended use 7
2.2 Description and features 7
2.3 Box contents 8
2.4 Serial number 8
2.5 Technical data 9
2.6 Symbols 10
2.7 Environmental 11
3. Preparation & adjustment 12
3.1 Assembly 12
3.2 Prior to use 13
4. Using the machine 14
4.1 Control panel 14
4.2 Morse taper spindle 15
4.3 Gearbox 16
4.4 Electromagnet 17
4.5 Switching motor on and off 18
4.6 Motor rotation 18
4.7 Motor speed control 18
4.8 Automatic functionality 19
4.9 LED display & torque control 20
4.10 Temperature control 21
4.11 Tool lubrication 21
5 Working with operating tools 22
5.1 Annular cutters 22
5.2 Twist drills 24
5.3 Machine taps 25
5.4 Countersinks 26
6. Maintenance 27
7. Trouble shooting 29
8. Exploded view & spare part list 31
8.1 Exploded views 31
8.2 Spare part lists 34
8.3 Wiring diagrams 36

3
1. Safety

1.1 General safety instructions

Do not use this power tool before you have thoroughly read and completely understood this
Instruction Manual and the “General Safety Instructions”, including the figures, specifications, safety
regulations and the signs indicating DANGER, WARNING and CAUTION.

WARNING: When using electrical tools basic safety precautions should always be followed to
reduce the risk of fire, electrical shock and personal injury including following.

Please also observe the relevant national industrial safety regulations. Non-observance of the safety
instructions in the said documentation can lead to an electric shock, burns and/or severe injuries.

This Operator’s Manual including the “General Safety Instructions” should be kept for later use and
enclosed with the power tool, should it be passed on or sold.

WORK AREA
1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
2. Do not operate magnetic drilling machine in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Magnetic drilling machine may create sparks which may
ignite the dust or fumes.
3. Keep bystanders, children, and visitors away while operating a magnetic drilling machine.
Distractions can cause you to lose control.

ELECTRICAL SAFETY
1. Magnetic drilling machine plugs must match the outlet. Never modify the plug in any way. Do
not us any adapter plugs.
2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is grounded.
3. Do not expose magnetic drilling machines to rain or wet conditions. Water entering a
machine will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord to carry the magnetic drilling machine or pull the
plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.
5. When operating a magnetic drilling machine, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
6. If operating a magnetic drilling machine in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when using a magnetic drilling
machine. Do not use machine while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating magnetic drilling machines may result
in serious personal injury.

4
 2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be
caught in moving parts.
3. Avoid accidental starting. Be sure switch is off before plugging in. Carrying magnetic drilling
machines with your finger on the switch or plugging in magnetic drilling machines that have
the switch on invites accidents.
4. Never place hands, fingers, gloves or clothing near cutting area or rotating machine parts.
5. Remove adjusting keys or switches before turning the machine on. A wrench or a key that is
left attached to a rotating part of the machine may result in personal injury.
6. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
enables better control of the magnetic drilling machine in unexpected situations.
7. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard
hat, or hearing protection must be used for appropriate conditions.
8. Always use supplied safety chain during any work on non-horizontal components. Mounting
can release.

MACHINE USE AND CARE

1. When using the machine on non-horizontal surfaces, you must use cutting paste. Do not use
oil because the oil can drip into the motor unit
2. During machine operations, the annular cutter must be cooled and lubricated with good
quality cutting or lubrication oil. Remove the slug from the annular cutter after each hole.
Caution, the slug may be hot!
3. Use clamps or other practical way to secure and support the work piece to a stable platform.
Holding the work by hand or against your body is unstable and may lead to loss of control.
4. Do not use machine if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
5. Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool. Such preventive safety measures reduce the risk of starting
the tool accidentally.
6. Store idle magnetic drilling machines out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
7. Maintain machines with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edges are less likely to bind and are easier to control.
8. Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the machine operation. If damaged, have the tool serviced before
using. Many accidents are caused by poorly maintained tools.
9. Use only accessories that are recommended by Euroboor for your model. Accessories that
may be suitable for one machine, may become hazardous when used on another machine.

SERVICE
• Tool service must be performed only by qualified repair personnel. Service or maintenance
performed by unqualified personnel could result in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow instructions in the
maintenance section of this manual. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of electric shock or injury.
• When using this machine, you MUST wear ear and eye protection.

5
1.2 Specific safety information

• Keep your fingers well out of the drill area;

• Avoid touching the drilled core that is automatically ejected by the centering pin when the
working procedure is finished. Contact with the core when it is hot, or if it falls, can cause
personal injuries;
• Always use the drill guard. Before switching on machine ensure the guard is closed securely;
• Always use the safety strap;
• The magnetic drilling machine is suitable for use on steel with a thickness starting from 5
mm, with zero air gap between the magnet core surface and the mounting surface.
Curvature, coats of paint and surface irregularities will create an air gap. Keep the air gap to a
minimum;
• Always place the machine on a flat surface
• Do not clamp the magnetic drilling machine on small or irregularly shaped objects;
• Always place the machine on a surface that is clear of shavings, chips, swarf and surface dirt;
• Keep the magnet clean and free of debris and swarf;
• Do not switch on the machine until it has been mounted and installed according to these
instructions;
• Do not switch on the machine before having checked that the magnetic stand has been
tightened firmly to the mounting surface;
• Adjust the table so cutter does not extend into the work piece before drilling. Do not
perform any design, assembly or construction activities on the work piece while the machine
is switched on;
• Before switching on the machine, make sure all accessories have been mounted correctly;
• Always use the recommended speed for the accessories and the material;
• Do not use the machine on the same work piece on which electric welders are being used;
• Use only an appropriate cutting fluid. We offer a range of premium cutting oils and lubricants
which are specially developed and selected for optimum performance and maximum tool
life;
• Do not use liquid cutting fluids while drilling vertically or overhead. Dip the cutter in cutting
paste or apply an appropriate spray for these applications;
• Do not pour cutting fluid into the reservoir while it is mounted in the bracket. Do not allow
cutting fluid to enter the drill motor;
• Before use, ensure movable chuck guard operates properly;
• Ensure that metal chips or resinous residue cannot lead to blockage of the function;
• In case of jammed cutter disconnect the machine from the power supply, remove the reason
for the jam before turning on the machine again.
• Always check if the situation before drilling in automatic mode is safe. Stay close by to the
machine and keep a close eye to the automatic drilling process to be ready to switch of the
machine whenever there is need to, especially when drilling in automatic mode.

RESIDUAL RISKS
In spite of the application of the relevant safety regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
• Impairment of hearing
• Risk of personal injury from flying particles
• Risk of burns due to accessories becoming hot during operation
• Risk of personal injury due to prolonged use.
Always try to reduce these risks as much as possible.

6
2. Description

2.1 Intended use

This magnetic drilling machine is intended for commercial use as a drilling machine for drilling
materials with a magnetizable surface using annular cutters and twist drills, and for countersinking
reaming and tapping in a weather-protected environment using the application tools and accessories
recommended by EUROBOOR.
The magnetic drilling machine can be used horizontally, vertically or overhead.

2.2 Description and features

1 LED display
2 Carbon brush cover
3 Gearbox guide
4 Magnet indicator
5 Speed control knob
6 Output shaft
7 Morse Taper spindle
8 Feed handle
9 Automatic feed motor
10 L/R switch
11 Motor switch
12 Fuse holder
13 Magnet switch
14 Electromagnet

[image 1-1]

7
2.3 Box contents

1 Carrying case
1 Magnetic drilling machine
1 Instruction manual
3 Handles
1 Drill guard + 2 bolts
1 Oil tank + attachment pin
1 Bottle cutting oil
3 Allen keys (2.5, 4, 5)
1 Safety chain
1 Morse Taper 3 spindle
1 Spindle drift
4 Tap collets (DIN 376 M10/M12/M14/M16)
1 Set of ear plugs
1 Pair of safety glasses
1 Pair of gloves

2.4 Serial number

The serial number is mentioned on the machine 3 times: engraved on the frame and magnet, plus on
the serial no. sticker on the motor housing. Additional serial no. stickers are provided with the
machine for your administration.

The serial number will help you and your sales point validate and identify the machine.

As example:

055T1501001

breaks down to:

055T 15 01 001
Machine series
Year of manufacture
Month of manufacture
Identification number

8
 2.5 Technical data

ANNULAR CUTTERS Ø 12 – 55 mm Ø 1/2" – 2 3/16”

TWIST DRILLS Ø 1 – 23 Ø 1/16” – 15/16”
THREADING M3 – M20 M3 – M20
COUNTERSINKING Ø 10 – 60 mm Ø 3/8” – 2 3/8”
LENGTH 345 mm 13 9/16”
WIDTH 305 mm 12”
HEIGHT 490 – 660 mm 19 5/16”- 26”
STROKE 170 mm 6 11/16”
WEIGHT 15,8 kg 35 lbs
MAGNET (L x W x H) 168 x 84 x 49 mm 6 11/16” x 3 3/8” x 1 7/8”
MAGNETIC FORCE 1850 kg 4100 lbs
MOTOR POWER 1600 W 14.5 A
TOTAL POWER 1700 W 15.6 A
SPEED UNLOADED [I] 60-275 min-1 [I] 60-275 min-1
[II] 100-500 min-1 [II] 100-500 min-1
-1
SPEED LOADED [I] 60-275 min [I] 60-275 min-1
-1
[II] 100-500 min [II] 100-500 min-1
SPINDLE MT 3 19,05 mm (3/4") Weldon MT 3 19,05 mm (3/4") Weldon
POWER SOURCE 110 – 120V AC / 60 Hz
220 – 240V AC / 50 – 60 Hz

9
2.6 Symbols

Symbol Term, meaning Explanation

Be absolutely sure to read the enclosed

Read documentation documentation such as the Instruction Manual and
the General Safety Instructions.

Wear ear protection Use ear protection during operation.

Wear eye protection Use eye-protection during operation.

Danger/warning/caution Observe the information in the adjacent text!

European conformity symbol Confirms the conformity of the power tool with
the directives of the European Community.
Product with basic insulation and exposed
Class of protection I (touchable), conductive parts additionally
connected to the protective earth conductor.

mm Millimeter Unit of measure for length, width, height or depth

kg Kilogram Unit of measure for the mass

V Volt Unit of measure for the electric voltage

A Ampere Unit of measure for the electric current intensity

W Watt Unit of measure for the output

N Newton Unit of measure for the force

min Minutes Unit of measure for the time

no No-load speed Revolution speed at no-load

1/min per minute Unit of measure for number of revolutions,

strokes, impacts or oscillations per minute.

10
2.7 Environmental

Separate collection. This product must not be disposed of with normal household waste.

Separate collection of used products and packaging allows materials to be recycled and used
again. Re-use of recycled materials helps prevent environmental pollution and reduces the
demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at
municipal waste sites or by the retailer when you purchase a new product.

11
3. Preparation & adjustment

3.1 Assembly

WARNING: To reduce the risk of injury, turn unit off and disconnect machine from power
source before installing and removing accessories, before adjusting or changing set- ups or
when making repairs. Be sure all switches are in the OFF position. An accidental start-up can
cause injury.

CHECKING THE FEED HANDLES

1. The three feed handles are pre-assembled on the machine
2. Check if the feed handles are fitted tightly. It should be possible to loosen and tighten them
by hand.
Be careful not to cross-thread any of the components.

MOUNTING THE DRILL GUARD

The guard protecting against chippings and accidental contact must always be mounted during
operation.
1. Hold the guard in front of the magnet, aligning the slots in the guard with the holes in the
magnet.
2. Fit the screws into the hole located in the side of the magnet.

WARNING: Always use the Safety guard.

FITTING THE LUBRICATION SYSTEM

The lubrication system can be used for horizontal drilling
applications (the drill being used vertically).

1. Hang the coolant tank (A) on the coolant tank holder

2. Position and tighten the attachment pin (B)
3. Connect the coolant hose (C) to the fitting on the Morse
Taper spindle. Make sure the hose is connected fully and tightly
4. To disconnect the coolant hose, press the blue ring on the
connection and gently pull out the hose

[image 2-1]

FITTING THE SAFETY CHAIN

1. Pass the safety chain through the frame grip opening
2. Wrap the chain around the work piece
3. Securely close the chain using the lock

WARNING: Always use the safety chain when using machine vertically and/or up-side-down.

12
3.2 Prior to use

Please make sure that the contacting surface for the magnet is level, clean and rust-free.
Remove any varnish or primer. When working on materials that are not magnetizable, suitable
fixation devices, obtainable as accessories from EUROBOOR, e. g. suction plate, vacuum plate or
pipe-drilling device must be used.
When work on steel materials with a material thickness of less than 5 mm, the work piece must
be reinforced with an additional steel plate in order to guarantee the magnetic holding power.

Check the machine for possible damage; Before using the machine, you must carefully check
protective devices or slightly damaged components to ensure they are operating perfectly and as
intended.
Check that moving are in perfect working order and do not jam and check whether parts are
damaged. All parts must be correctly installed and fulfill all conditions necessary to ensure perfect
operation of the machine.
Damaged protective devices and parts must be repaired or replaced according to specifications by
EUROBOOR of any authorized EUROBOOR dealer.

DO NOT use under wet conditions or in presence of flammable liquids or gases. This magnetic drilling
machine is a professional power tool.

DO NOT let children come into contact with the machine. Supervision is required when
inexperienced operators use this machine.

ELECTRICAL SAFETY
The electric motor has been designed for one voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.

Your EUROBOOR MAGNETIC DRILLING MACHINE is designed in class I (grounded) according to

EN 61029-1. Earth wire is required.

If the supply cord is damaged, it must be replaced by a specially prepared cord available through the
EUROBOOR service organization.

EXTENSION CABLE
If an extension cable is required, use an approved 3-core extension cable suitable for the power input
of this tool (see technical data).The minimum conductor size is 1.5 mm²; the maximum length is 30
meter. When using a cable reel, always unwind the cable completely.

TRY A FEW SIMPLE PROJECTS USING SCRAP MATERIAL UNTIL YOU DEVELOP A “FEEL” FOR THE
MACHINE

LET THE MACHINE RUN IN FOR A PERIOD OF 8-10 HOURS BEFORE STARTING WITH BIG
OPERATIONS. DO NOT LOAD THE MACHINE TOO MUCH DURING RUN-IN PERIOD

NEVER USE THE MACHINE IN SERIOUS OVERLOAD

KEEP THE MACHINE CLEAR FROM MOISTURE AT ALL TIMES TO PROTECT THE MACHINE, YOURSELF
AND OTHERS.

13
4. Using the machine

WARNING: Always observe the safety instructions and applicable regulations.

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from
power source before making any adjustments or removing/installing attachments or
accessories.

4.1 Control panel

The control panel on your magnetic drilling machine is designed for maximum operating facility and
safety.

1. L/R Switch *

2. Motor Switch

3. Magnet LED Indicator

4. Fuse holder with Fuse

5. Speed control knob

6. Magnet Switch

[image 2-2]

14
4.2 Morse Taper spindle

[image 2-3] [image 2-4]

1. Make sure the inside of the output shaft and the Morse Taper spindle are clean and free of
grease
2. Align the coolant ring rotation limiter with the recess in the gearbox (A)
3. Firmly slide the Morse Taper spindle into the output shaft by hand (B). Make sure the spindle
is properly positioned. You should not be able to pull it out by hand.
4. To remove the Morse Taper spindle
- Switch of the motor
- Rotate the mechanical gear switch to neutral (see chapter Gearbox)
- Rotate the output shaft until the slots on the shaft align with the slots on the gearbox
- Gently tap the supplied drift into the slots to push the Morse Taper arbor out

15
4.3 Gearbox

1. To select the correct gear from neutral (horizontal) position:

a. Rotate the switch counterclockwise to position o, this is gear 1
b. Rotate the switch clockwise to position oo, this is gear 2
2. A gear is only correctly selected when the gearbox switch is aligned with the indicators on
the gearbox.
In case you have trouble fully and correctly selecting a gear, the gears in the gearbox
might be misaligned. Slightly rotating the output shaft by hand will help you align the
gears and correctly and fully selecting the intended gear.
NOTE: never touch moving machine parts!
3. Speed selection for annular cutters (also see plate on gearbox):
o Ø 27-55 mm Rotating speed 60-275min-1
oo Ø 12-26 mm Rotating speed 100-500min-1

[image 2-5]

WARNING: never touch moving machine parts!

16
4.4 Electromagnet

Make sure the magnetic drilling machine is placed on a smooth, clean, level and solid surface without
any objects or dubree in between to guarantee maximum adhesion

The workpiece must be at least 5 mm thick for the magnet to stick, but minimal 3 mm thick to hold
the weight of the machine and to drill safely. In case the workpiece is between 3 and 5 mm, make
sure to make a proper base to create a good magnetic field as shown in image 2-6.

[image 2-6]

The electromagnet will work best on surfaces of at least 10 mm thickness.

The electromagnet may not be able to create a good enough magnetic field. Causes may be:
- Surface not flat
- Workpiece not magnetizable (e.g. aluminium)
- Workpiece coated or painted
- Workpiece not thick enough
In this situation the magnet indicator will light up red. Make sure to solve any of these matters
before proceeding in any way and creating unsafe situations

1. Connect the machine to the mains/work piece

2. To activate the magnet, press the red magnet switch
The magnet switch will be lit (red)
The LED indicator lights up GREEN when generated magnetic force is sufficient
3. To deactivate the magnet, press the same switch again

WARNING: Do not use this machine when LED indicator is RED. Magnet may not generate
sufficient attachment force

We need to point out that this is only an indication and not a certainly that the magnet will not
release from the material. Euroboor accepts no liability ensuring from the magnet indicator not
functioning or functioning poorly.
17
Make sure that the magnet attaches tightly to the work piece before turning on the motor unit of the
magnetic drilling machine. Euroboor magnets have 2 coils; make sure that both coils are in contact
with the material. Do not connect any other machines to the electrical outlet the magnetic drilling
machine is plugged into, as it may result in the loss of magnetic force.

Always use the safety chain included. Drilling above your head is extremely dangerous and is not
recommended. For the use of magnetic drilling machines on pipes, not-flat or non-magnetic
materials, we refer to our brochure or our website www.euroboor.com where several vacuum
tightening systems and pipe clamping systems are mentioned.

4.5 Switching motor on and off

The motor unit can only be switched ON when the magnet is activated. To switch the motor ON,
press the green button with marking “I”. To switch the motor OFF, press the red button with marking
“O”.

4.6 Motor rotation

ECO.55-T only

The rotational direction of the motor can be changed.

- Switch in up position (R) will make the motor rotate clockwise
- Switch in down position (L) will make the motor rotate anticlockwise
- Switch in middle position will not make the motor rotate (neutral position)
Before switching the rotational direction of the motor and spindle, make sure the motor is switched
off first to prevent machine and tool damage.

4.7 Motor speed control

ECO.55-T only

The speed control knob (potentiometer) allows you to electronically control the speed of the motor
(in both clockwise and anticlockwise direction).
- The indicator of the potentiometer in bottom left corner is minimum speed
- The indicator of the potentiometer in bottom right corner is maximum speed
The electronic motor speed control works for both mechanical gears.
Be careful not to overturn the knob.

18
4.8 Automatic functionality

1. Feed handle positioning

a. When the feed handles are folded flat against the machine (in a 90 degree angle to
the workpiece), the machine is in manual standby position.
In manual standby position it is possible to operate the machine for all suitable tasks
(drilling with annular cutters & twist drills, countersinking, reaming and tapping) by
applying manual feed pressure.
b. When the feed handles are folded out (in a 45 degree angle to the workpiece), the
machine is in automatic standby position
In automatic standby position it is possible to start the automatic feed by simply
pressing the ON switch. This is possible with the motor in every height position.

Manual standby position Automatic standby position

[image 2-7]

WARNING: Using the automatic feed function is only possible when drilling with annular
cutters up to Ø 55 mm. For Ø 30 – 55 mm the use of TCT annular cutters is advised to ensure
the fastest and most efficient (automatic) drilling performance.

2. Automatic drilling machines are equipped with a penetration recognition. When drilling with
annular cutters in automatic mode, the magnetic drilling machine recognizes when the hole
is finished. The machine will automatically return to a specified height position and shut off
the motor by itself.
3. When there is not sufficient magnetic force, it is not possible to use the automatic drilling
functionality. The magnet indicator will be lit red as warning.
4. During the process of drilling with annular cutters, It is possible to switch from manual to
automatic mode and vice versa.

19
 WARNING: Always check if the situation before drilling in automatic mode is safe. Stay close
by to the machine and keep a close eye to the automatic drilling process to be ready to switch
of the machine whenever there is need to.

4.9 LED display & torque control

This machine is equipped with an electronic display, showing:

- Used motor power
- LED indicators

1. Switch on the electromagnet. All LED indicators shortly light up and a beep sounds
2. Switch on the motor and start drilling. When the tool first touches the workpiece the used
motor power shown in the display increases, and can be increased or decreased by raising of
reducing the pressure on the feed handles.

The LED indicators will help you drill at optimum load:

[image 2-8]

Phase 1 Phase 2 Phase 3 Phase 4 Phase 5

1 blue light + 1 blue light + 1 yellow light + 1 red light Flashing red
light + beep
sound
Load Optimum load Acceptable Close to Overload limit
overload overload exceeded,
motor stops
Slightly increase Maintain feed Slightly reduce Reduce feed Reduce feed
feed pressure pressure feed pressure pressure pressure
when possible when possible

When the motor is in overload (phase 5), the Smart Restart torque control technology
ensures trouble-free continuation of your drilling job. When the feed pressure is reduced, the
machines electronics recognize the reduction and the motor continues within a few seconds.

WARNING: The displayed motor power usage and LED indicators are only an indication of
correct cutting performance. Always keep an eye on the workpiece, tool and machine and
check if the cutting performance is as it should be, especially when drilling in automatic mode.

20
 WARNING: Never touch any potentially moving parts as long as the motor switch is still
switched on!

4.10 Temperature control

The ECO.55-(T)A is equipped with an all-time electronic temperature protection. If the temperature
of the motor unit runs up to 70 Degree Celsius the motor unit will stop. After a few minutes it can be
started again.
When it is possible to start the motor again, let the motor run idle at full speed for a couple of
minutes to let the motor cool down more in an efficient way.

4.11 Tool lubrication

IN HORIZONTAL APPLICATIONS
In order to use the lubrication system, the tank must be filled with a cutting fluid or oil
1. Make sure the flow regulator is closed
2. Unscrew the cap
3. Fill the container with cutting fluid or oil
4. Screw the cap back on

• Adjust the fluid flow as required using the flow regulator;

• Add more cutting fluid if the shavings (metal chips) become blue.

VERTICAL AND OVERHEAD APPLICATIONS

Dip the cutter in cutting paste or apply an appropriate spray.

WARNING: Do not use the lubrication system in vertical or overhead drilling applications.
Instead use Euroboor cutting paste

Make sure to use only suitable cutting oil or fluid. Euroboor offers a wide range of cutting lubricants
for all tool and material combinations. Proper cooling will help you create better and faster results,
and extend the lifetime of your tools.

21
5 Working with operating tools

5.1 Annular cutters

Annular cutters only cut material at the periphery of the hole, rather than converting the entire hole
to shavings. As a result, the energy required to make a hole is lower than for a twist drill.
When drilling with an annular cutter, it is not necessary to drill a pilot hole.

WARNING: Do not touch the cutter or the parts close to the cutter immediately after
operation, as they may be extremely hot and cause burns to the skin. Ensure nobody is in the
work area where the metal core is ejected.

DRILLING CONDITIONS
The ease with which material can be drilled depends on several factors including tensile strength and
abrasion resistance. Whilst hardness and/or strength is the usual criterion, wide variations in
machinability can exist among material showing similar physical properties.

The drilling conditions are dependent on requirements for tool life and surface finish. These
conditions are further restricted by the rigidity of the tool and the work piece, lubrication and
machine power available. The harder the material, the lower the cutting speed.

Some materials of low hardness contain abrasive substances leading to rapid cutting edge wear at
high speeds. Feed rates are governed by rigidity of set-up, volume of material to be removed, surface
finish and available machine power.

DRILLING A HOLE
Now that you have read the explanatory information and safety recommendations above, you are
ready to actually start drilling. Follow these 12 steps for best drilling result :

1. Install the annular cutter

- Place the pilot pin into the cutter
- Align the flat faces on the cutter shank with the screws in the tool holder
- Make sure the cutter shank is entered fully and correctly (1)
- Tighten the screws (2)

[image 3-1]

2. Precisely mark the centre of the hole

3. Use the pilot pin to position the machine and in the correct position, with the tip of the pilot
pin to meet the marked center of the hole.
22
 4. Switch on the magnet and verify that the drill is in the right position and that the machine is
pushed tight against the work piece.

5. If your machine is equipped with a auto coolant system, put open the valve to release the oil.
If your machine does not have an auto coolant system, fill the holes of the spindle with oil.

6. Switch the motor on at and allow it to run at the required speed. *

7. Turn the arms to start drilling. Apply only a slight pressure when the annular cutter touch the
metal. Do not push the annular cutter with force into the metal. *

8. Apply a regular pressure while drilling. The drilling performance does not improve by putting
more pressure on the tool. Too much pressure will overload the motor and your annular
cutter will be worn sooner. *
A continuous, non-discoloured iron swarf is a sign of correct drilling speed and a well-
cooled, sharp cutter. Let the cutter do the job and give it time to cut the metal!!!

9. Adjust the oil supply when necessary, if your drill does not have an auto coolant system, stop
drilling regularly, refill the holes of the spindle and continue drilling. *

10. Apply less pressure when the drill cuts through the material. The slug will be pushed out of
the cutter by the pilot pin.*

11. Turn the arms to put the motor in highest position and switch off the motor unit. *

12. Remove the burrs, metal chips and clean the cutter and surface without getting injuries.

Caution: The metal piece drilled out can be sharp and very hot!!

* When drilling in automatic mode, steps 6 – 11 are taken care of automatically by the magnetic
drilling machine itself. Always check if the situation before drilling in automatic mode is safe. Keep a
close eye to the automatic drilling process and be ready to switch of the machine whenever there is
need to.

23
5.2 Twist drills

1. Remove the Morse Taper arbor (see chapter Gearbox)

2. Fit the twist drill
a. Straight shank twist drills

[image 3-2]

b. Morse Taper shank twist drills

[image 3-3] Morse Taper 2 [image 3-4] Morse Taper 3

3. Precisely mark the center of the hole, and use the tip of the twist drill to position the
machine and in the correct position, with the tip of the twist drill to meet the marked center
of the hole.
24
 Steps 4-12: see chapter Annular cutters. Make sure the machine runs at maximum speed for
twist drills!

WARNING: Do not use the automatic feed mode when drilling with twist drills. Manual feed
only!

5.3 Machine taps

The ECO.55S/TA model is equipped with a reversible direction of rotation and can also be used for
cutting threads. Proceed as follows for cutting threads:
1. Install the tap

[image 3-5]
2. Drill the hole for the thread on the recommended size of the tap
3. Switch off the machine and change the cutter for the tap collet and the machine tap. DO NOT
MOVE THE MACHINE
4. Select the lowest gear and lowest speed and set the direction of rotation to clockwise (right
= R)
5. Switch on the machine and set the machine tap onto the drilled hole
6. Guide the machine slide down at the handle without exerting
7. Switch off the machine (just before the tap is completely through the hole) and set the
direction of rotation to anti-clockwise (left = L) at switch

25
Switch on the machine again and allow the machine tap to come completely out of the work piece.
Then guide the motor unit slide upwards at handles to avoid damaging the start of the thread. DO
NOT LET YOUR TAP PUSH UP THE MOTOR UNIT BY ITSELF!!

Make sure the properly lubricate while performing tapping work, see chapter Annular cutters

WARNING: Do not use the automatic feed mode when using machine taps. Manual feed only!

5.4 Countersinks

Thanks to its wide range of operating speeds, the machine can also be used for reaming or counter-
sinking.

Follow the steps mention in chapter Twist drills

WARNING: Do not use the automatic feed mode when using countersinks. Manual feed only!

26
6. Maintenance

Your EUROBOOR power tool has been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and
regular cleaning.

CAUTION: To reduce the risk of injury, turn unit off and disconnect machine from power
source before installing and removing accessories, before adjusting or changing set- ups or
when making repairs. Be sure the switch is in the OFF position. An accidental start-up can
cause injury.

Just as every magnetic drilling machine with moving parts, your Euroboor magnetic drilling machine
also needs regular maintenance service. A few recommendations follow :

VISUALLY CHECK THE MACHINE FOR DAMAGE

Machine must be checked before operation for any signs of damage that will affect the operation of
the machine. Particular notice must be taken of the mains cable, if the machine appears to be
damaged it should not be used failure to do so may cause injury or death.

CLEANING
- Clean all dirt, dust, metal chips and burrs of your magnetic drilling machine
- Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in
and around the air vents. Wear approved eye protection and an approved dust mask
- Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool.
These chemicals may weaken the materials used in these parts. Use a cloth dampened only
with water and mild soap. Never let any liquid get inside the tool; never immerse any part of
the tool into a liquid.

OPERATION OF THE MACHINE

The machines operation must be checked to ensure that all components are working correctly.
Replace any defective parts immediately. This prevents properly function parts from being damaged.

CARBON BRUSHES
Brushes should be checked to make sure there is no abnormal wear present. This should be checked
at least once a week if used frequently. If the carbon brush has worn more than 2/3 the original
length the brushes should be changed. Failure to do so may cause damage to the machine.

CHECK MAGNETIC BASE

Before every operation the magnetic base should be checked to make sure that the base is flat and
there is no damage present. An uneven magnet base will cause the magnet not to hold as efficiently
and may cause injury to the operator.
When the machine us put out of use for a longer period, apply a small amount of machine oil to the
underside of the magnetic base for rust protection. Clean the magnetic base again with next use.

CHECK MACHINE OIL

The gearbox oil should be checked and replaced at least once a year to ensure maximum lubrication
and cooling, and thus the best performance of the machine.

27
CHECK ARMATURE
This should be checked at least 1 per month to check that there are visual signs of damage to the
body or to the commutator. Some signs of wear will be seen on the commutator over a period of
time this is normal as this is the part that comes in contact with the brushes but any signs of
abnormal damage and the part should be replaced.

ADJUSTMENT OF SLIDE
An essential requirement of the machine is that the slide can move in a smooth and controlled
manner, free of lateral movement and vibration.

This situation can be maintained by periodic adjustment of the slide and is accomplished in the
following manner:
1. Place the machine in an upright position and, by means of the capstan, raise the slide to its
highest position. Clean the aluminum rails and apply a small amount of light machine oil to
the wear surfaces
2. Gently feed in setting screw with supplied Allen key 2.5 until slight resistance is encountered.
Follow your way down adjusting all setting nuts and screws
3. Operate the slide up and down a few times to test the movement and make any further
necessary adjustments. Try to ensure that all the screws are exerting a uniform pressure on
the slide from top to bottom. A perfectly adjusted slide will operate freely up and down
without any sideways movement

LUBRICATING THE FEED TRAVEL

The feed travel should be lubricated periodically with grease to ensure smooth operation.
- Raise the motor unit to the highest position possible
- Lubricate the dove-tail guide way at both sides
- Lubricate the gear rack

After repeated use, the gear rack may become loose. If necessary, adjust the 5 self-locking set
screws at the left side. Tighten screws in series until the gear rack moves freely in the dove-tail guide
but does not allow the motor to wobble.

MAINTENANCE OF AUTOMATIC FEED ARM MECHANISM

For the maintenance of the automatic feed arm mechanism we refer to a specialized workshop.

REPAIR, MODIFICATION AND INSPECTION

Repair, modification and inspection of Euroboor Magnetic drilling machines must be done by
EUROBOOR or an EUROBOOR authorized dealer. The spare parts list will be helpful if presented with
the machine to the Euroboor dealer for service when requesting repair or other maintenance.

Euroboor machines are constantly being improved and modified to incorporate the latest
technological advancements. Accordingly, some parts (i.e. part numbers and/or design) may be
changed without prior notice. Also, due to Euroboor’s continuing program of research and
development, the specifications of machines are subject to change without prior notice.

WARNING: Since accessories, other than those offered by EUROBOOR, have not been tested
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only EUROBOOR recommended accessories should be used with this product.

Consult your dealer for further information on the appropriate accessories.

28
 7. Trouble shooting
Magnet and motor do not - The magnet switch is not connected to the power supply
function - Damaged or defective wiring
- Defective fuse
- Defective magnet switch
- Defective Control Unit
- Defective power supply
Magnet does function, the motor - Damaged or defective wiring
does not work - Carbon brushes are stuck or worn out
- Defective magnet switch
- Defective On / Off switch
- Defective Control Unit
- Defective armature and/or field
Magnet does not function, the - Defective magnet
motor does - Defective wiring of magnet
- Defective Control Unit
Automatic feed function does not - Insufficient magnetic force
work - Feed handle mechanism needs adjustment
- Carbon brushes are stuck or worn out
- Defective Control Unit
- Defective motor unit
Annular cutters break quickly, - Clearance in the guide
holes are bigger than the hole - Bent spindle
cutter - Shaft extending from the motor is bent
- Bent pilot pin
Motor running roughly and/or - Bent spindle
seizing up - Shaft extending from the motor is bent
- Triangular guide not mounted straight
- Dirt between spindle and triangular guide
Motor starts running when - Damage or defective relais in control unit
magnet switch is turned on
Motor making a rattling sound - Gear ring (bottom of the armature) worn out
- Gear(s) worn out
- No grease in gear box
Motor humming, big sparks and - Armature damaged (burned)
motor has no force - Field burned
- Carbon brushes worn out
Motor does not start or fails. - Damaged or defective wiring
- Dirt in sensor Speed Control Unit
- Defective or loose magnet on top of armature
- Damaged or defective (sensor) Speed Control Unit
- Damage to Armature or field coil
- Damaged or defective carbon brushes
Guiding takes a great deal of - Guide is set too tight
effort - Guide is dry, needs to be greased
- Guide/gear- rack/rotation system dirty or damaged

29
Insufficient magnetic force - Damaged or defective wiring
- Bottom of magnet not clean and dry
- Bottom of magnet not flat
- Work piece is not bare metal
- Work piece is not clean or flat
- Work piece is less than 10 mm (too thin)
- Defective Control Unit
- Defective magnet
Frame under voltage - Damaged / defective wiring
- Defective magnet
- Motor seriously dirty
Fuse blows when magnet switch is - Damaged or defective wiring
turned on - Wrong value fuse
- Defective magnet switch
- Defective Control Unit
- Defective magnet
Fuse blows when motor is started - Damaged or defective wiring
- Wrong value fuse
- Motor running roughly
- Defective Armature and / or Field
- Carbon brushes worn out
- Defective Control Unit
Rotation system free stroke too - Loose or defective gear-rack
long - Defective rotation system
Red blinking light in top display Machine is in overload protection
with buzzer sound
Red burning light in top display Machine is in overheat protection
with buzzer sound

30
8. Exploded view & spare part list

8.1 Exploded views

31
32
33
 8.2 Spare part lists
No Part number Description Qty No Part number Description Qty
055T.1001 Motor unit 220-240 V 56 020.0063 Screw M5x20 2
1
1 055T.1001A Motor unit 110-120 V 57 020.0289 Coolant hanger 1
2 050.0106 Screw 4,8xx45 8 050.1015 Gear box 230V
58 1
3 050.0059 Protective cover 53 x 35 1 050.1019 Gear box 110V
4 050.1013 Led screen 1 59 050.0068 Bearing 61906DDU 1
5 050.0060 Screw M3 x 5 4 60 020.0146 Screw M6 x 25 1
6 050.0133 End plate 2 61 020.0111 Washer M6 DIN7980 5
7 050.0130 End cover 1 62 050.0077 Key 6 x 6 x 12 1
8 050T.0332 Screw for speed control unit 2 63 050.0461 Spindle drive shaft 34x146 1
055T.0011 ECO.55S/TA Control unit 2 - 230V 64-65 020.0086/Z Rail set Aluminium (L + R) Z-profile 1
9 1
055T.0011A ECO.55S/TA Control unit 2 - 110V 66 020.0063 Screw M5x20 6
050.0147 Carbon brush set - 230V 67 020.0101 Panel Screw BKVZM4x8 4
10 1
050.0148 Carbon brush set - 110V 055.0002 Rear panel plate 230V
68 1
11-16 050.0371 Carbon brush holder 1 055.0002A Rear panel plate 110V
17 050.0586 Cable housing 1 055T.1012 ECO.55S/TA Speed control unit - 220V
69-74 1
050T.0002 Control Unit 1 230V 055T.1012A ECO.55S/TA Speed control unit - 110V
18 1
050T.0003 Control Unit 1 110V 75 020.0298 Motor cable clamp 1
19 050.0131 Housing 1 76 020.0081 End Screw BKVZM6x20 1
20 050.0587 Screw pkvz 4,8 x 35 4 77 020.0077 End plate 1
050T.0278 Field 230V 78 050.0063 Bearing 1
21 1
050T.0278A Field 110V 79 020.0516 Screw SS M5 x 10 4
22 020.0328 Screw M4 x 70 2 80 055.0006X Frame 1
23 050.0261 Baffle 1 81 020.0046 Motor cable 1
24 050T.0346 Rubber ring 1 82 020.0041 Coupling nut (motor cable) PG9 2
25 050T.0180 Armature speed disk 1 83 050.0056 Stepper motor 1
26 032.0126 Bearing 8x22x7 608 1 84 050.0028 Washer Φ25xΦ37x3.0 1
050T.0183 Armature 230V 85 040.0086 Bearing 6001DDU 1
27 1
050T.0183A Armature 110V 86 055.0016 Screw M4x5 1
28 032.0166 Circlip 472/28/1.2 1 87 050.0042 Worm 1x0.9 1
29 032.0171 Bearing 6001 12 x 28 x 8 1 88 055.0008 Bearing 628/7-ZZ 1
30 050.0064 Oil bearing 15 x 21 x 3 1 89 050.0033X Gear box plate 1
31 050.0236/Y Inner gear plate 1 90 020.0229 Screw M4x20 2
32 040.0161 Needle bearing HK 0810 3 91-101 055.1003 Drilling rocker arms 1
33 050.0065 Metal ring diam. 40 1 102 030.0030X Arm for capstan 3
34 050.0176 Circlip 471/11 1 103 050.0027 Washer Φ36xΦ42x0.2 1
35 050.0071 O-ring 82 x 1.8 1 104 055.0017 Bearing 61907 1
36 050.0207 Gasket middle 1 105 050.0044 Circlip Φ35 1
37A 050.0251 First gear 1 106 050.0041 Turbine - 50x0.9 1
37B 050.0246 Gear shaft 1 107 050.0029 Washer - Φ28.5xΦ38x2.0 1
38 050.0171 Gear 34/40Z 1 108 050.0045 Circlip Φ28 1
39 050.0231 Axle 13T 1 109A 020.0031 Coupling nut (Main cable) PG11 1
40 100.4496 Key 5x5x28 1 020.0036 Main cable complete 220-240V
41 020.0156 Screw SSM6x20 5 020.0036/AU Main cable Australia
42 050.0074 Rack - 1.5X39T 1 109B 020.0036/UK Main cable UK 230v 1
43 050.0076 Circlip diam. 20 1 020.0036/UK 110-16A Main cable UK 110v 16A
44 050.0463 Gear 1 x 45T 1 020.0036/USA Main cable USA
45 050.0462 Washer 20.5 x 28 x 0.2 1 110-111 020.0182 Grounding Screw/washer/Nut 1
46 030.0009 Bearing 6004DDU 1 112-114 020.0037 Cable clamp 1
47 050.0066 Oil bearing 28 x 38 x 7 1 115 020.0257 Capacitance 1
48 050.0078 Ring 41.5 x 36.5 x 1.5 1 116 055.0018 PCB box-2 1
49-51 050.1016 Gear switch assembly 1 117 055.0007 Drive Board 1
52 020.0329 Screw M4 x 16 1 118 055.0019 PCB box-1 1
53 050.0082 Screw holder 1 119 032T.0019XA Screw M3X8 3
54 050.1005A Clutch shaft 1 120 050.0048 Panel washer 1
55 032.0211 Casing pin 4 x 12 1 121 020.0183 Screw 4

34
122 055T.0049 Front panel plate 1 200 CAS.55A Case 55 auto 1
123 055.0022 Screw M4x12 4 201 KSP.Q2 Coolant System Quick Connect 1
124 100.0152 R/L Switch (push) 1800 W 1 202 IBO.10.200 Cutting Oil 200ml 1
030E.0091/Y Motor switch (5-pin) 220-240V 203 SAF.300 Protective gloves 1
125 1
030E.0092/Y Motor switch (5-pin) 110-120V 204 SAF.400 Safety chain (1 mtr) with lock 1
126 020.0017 Fuse 5x20 F2A 1 206 SAF.200 Ear plugs 1
127 020.0016 Fuse holder 1 207 IMB.US2.5 Allen key 2.5 mm 1
128 020.0011 Magnet switch 1 208 IMB.US3 Allen key 3 mm 1
129 020.0206 LED indicator set 1 209 IMB.US4 Allen key 4 mm 1
130 050T.1009 Potentiometer (turn)Knob 1 210 IMB.US5 Allen key 5 mm 1
131 055.0024 Washer 1 211 SAF.100 Safety goggles 1
132 020.0111 Washer M6 DIN7980 4 212 Drift3 Drift MT3 1
133 020.0201/2 Sensor 1 213 SAF.MDMB Safety Guard 1
134 050.1003 Magnet 1 214 020.0511 Bolt M5x10 2
215 IMC.30/19-N Arbor MT3 - 19.05 (3/4") Weldon 1

35
8.3 Wiring diagrams

36
37