Foxboro Evo™

Process Automation
System
Product Specifications

PSS 31H-8K1

Foxboro Evo™ SCD6000 Input/Output Modules

OVERVIEW
The Foxboro Evo™ Input/Output Modules are used  4 Channel Analog Output Module
with SCD5200/SC6000. They provide a means for  Digital Output Module.
monitoring and control of Industrial plants. Field Interrogation Power Supply (FIPS) options for
digital inputs include nominal 24 V to 129 V,
INTRODUCTION selectable via jumper settings.
The Foxboro Evo™ Input/Output Modules provide A 1 kV isolation option is available for the analog
connection of wide range of field equipment and inputs on the Analog Digital Input (ADI) Module and
devices to the SCD5200/SCD6000 Station 20 Channel Analog Input Module.
Computing Devices for monitoring and control of
Latched and non-latched relay options are available
industrial plant.
on Digital Outputs.
The range of I/O modules comprises:
Key features of the range include:
 Multi I/O Module
 Opto-isolated digital inputs
 Analog Digital Input (ADI) Module
 Relay-isolated digital outputs
 20 Channel Analog Input Module
 High isolation optional on analog inputs
PSS 31H-8K1
Page 2

 Analog outputs individually isolated The one I/O card file and five I/O card file options
 High security “check-before-operate” control (Refer PSS 31H-8G1 SCD5200 Architecture
outputs Overview) aim to meet the needs of small I/O and
 Sequence of Events resolution of 1 ms space limited applications.
 High resolution analog inputs (12 bit plus sign) The Multi I/O Module provides the highest I/O density
and analog outputs (12 bit) of combined digital input, analog input, and digital
 Digital inputs provide Status, Momentary Change output (24 DI, 6 AI, and 6 or 8 DO). The ADI Module
Detect, Accumulator, and Sequence of Events (32 DI and 4 AI) provides for high density input-only
 Software configurable configurations.
• Digital outputs as individual variable pulse or Where greater flexibility of configuration, connection,
latched, trip/close or raise/lower pairs, and/or isolation is required, the Analog Input
multiple relay variable pulsed or latched Modules, Analog Output and Digital Output Modules
• Analog output range and offset, open loop may be combined with the high density Multi I/O and
detection ADI Module types.

 High transient and surge immunity As the modular design of the SCD5200/SCD6000
 EMC emission and immunity to CE standards for allows any mix of I/O modules, a wide range of
industrial equipment number and type of I/O connections may be
 Analog current loop resistors integral to terminal economically accommodated.
boards The I/O module range is designed and tested for
 Enclosed insulated terminal assemblies for safety application in the most demanding industrial
 Removable terminal assemblies allow card environments. Compliance standards include
replacement without disconnecting field wiring European Community (CE) Electro-Magnetic
 Run/fail status front panel indicator and database Compliance (EMC) immunity and emissions, transient
health point and surge immunity, isolation, and electrical safety.
 High density for compact connection of large I/O CE Mark certification and CE compliant installation
count guidelines are available.
 Range of I/O combinations provides connection
Software complements the I/O module hardware.
flexibility at minimum cost.
Momentary Change Detect, Sequence of Events,
Through flexible I/O configurations and options, the and Accumulator functionality is provided for digital
range of I/O Modules is matched to a wide range of inputs. Digital outputs are highly secure, incorporate
applications. “check before operate” execution, and may be
The combination of a ten I/O module capacity file, configured as variable pulse, latch, trip/close pairs, or
integrated local network capability, and high I/O multiple relay groups (set point).
density modules can accommodate large to very
large I/O counts while providing excellent value for
money.
 PSS 31H-8K1
Page 3

FUNCTIONAL DESCRIPTION
NOTE
Analog/Digital Input Modules The Analog/Digital Input Module is available
The Analog/Digital Input Module provides flexible in two variants to support two different sizes
data collection and input monitoring facilities through of wires in terminal assembly. The size of the
32 individually configured digital inputs and four high- wire is based on insulation requirements,
resolution analog inputs. that is, thicker wires are required to support
The Analog/Digital Input Module has 1 kV isolation on higher insulation requirements.
the analog inputs. SY-0399160 accommodates wire sizes of
The module supports digital inputs over the nominal 0.5 sq.mm and SY-0399222 accommodates
ranges of 24 V to 48 V and 48 V to 129 V. A jumper wire sizes of 1sq.mm.
for each digital input can be individually set to select The thickest wire size supported for a fully
either of these ranges. The factory default setting is
populated IO count [45 wires] is 0.75 sq.mm
for 48 V to 129 V operation. for the SY-0399160 and 1.0 sq.mm for the
WARNING SY-039922. In all other respects, SY-
0399222 is identical to SY-0399160.
In this module, the jumpers J3 to J34 must
be removed when using digital input voltages Digital Inputs
in the range 60–129 V (dc) or 72–144 V RMS The digital input subsystem processes 32 contact
(ac). Failure to do so may result in permanent inputs. The module optically isolates, filters, and
damage to the module and possible electric protects against surge transients. It interfaces the
hazard. contact state to the on-board microprocessor.
Features Digital input circuits employ contact bounce
Key features of the ADI Modules include: elimination circuitry, which rejects noisy contact
transitions until the input signal has been stable for
 Removable plug-connected terminal board
2 ms.
 Plug in current loop resistors
 Software configurable digital inputs The digital inputs are grouped into four groups of
 Optical isolation on digital inputs eight, with a common terminal for each group. Each
 Galvanic isolation on analog inputs group accepts common positive or common
 Common voltage inputs (+VE or –VE) that are negative.
selectable in groups of eight digital inputs Digital inputs status is provided by scanning every
 Digital input bounce elimination circuitry millisecond. Sequence of Events with one millisecond
 Individually configurable chatter filters resolution time-tagging is available.
 RUN/FAIL LED indicator.
In addition, each of the digital inputs supports
accumulator and Momentary Change Detection
functionality.
PSS 31H-8K1
Page 4

Analog Inputs  Removable plug-connected termination

The analog input subsystem consists of individually assembly
isolated amplifiers and analog-to-digital converters  Control output duration is individually
for each input. Each input is measured and configurable.
converted to a 12-bit plus sign value and has Module Description
automatic zero drift correction and calibration scale The digital output subsystem provides security and
checking. The conversion provides a nominal range control for twelve electrical or magnetically latched
of values from -4000 to +4000 for inputs from -2V to relays. The 12 Channel Digital Output Modules
+2V with overrange capability to ±2.0475 Volts. The consist of an on-board microprocessor and security
plug-in current loop termination resistor value for circuits mounted on a logic board with a plug-in relay
each input is selected so as to provide a 2 Volt signal and terminal assembly. Configuration data from the
for the nominal full-scale current loop range. main processor (COPE) determines the control of
each output relay by the on-board processor.
12 Channel Digital Output Modules
Digital Output Subsystem
Two versions of the output module are available:
The 12 Channel Digital Output Module contains
 12 Pilot Relay Output Module source and sink drivers for 12 relays. Each relay may
 12 Magnetically Latched Relay Output Module be driven as fixed length pulse outputs, variable
The 12 Channel Digital Output Modules offer several length pulse outputs, or latched outputs.
configuration possibilities. Relay outputs can be Two-Pass Operation
configured as individual relays, pairs, or multiples in During pass 1, the on-board microprocessor accepts
set point combinations. Two-pass operation with command data from the main processor (COPE). The
built-in hardware checking ensures reliable control validity of the command is confirmed and then the
over equipment. hardware is checked on the output driver circuits. If
Features tests succeed, feedback of the command is sent to
Key features of the Digital Output Modules include: the main processor.
 12 independent relays During pass 2, the main processor (COPE) sends the
 Magnetically latched relays are optional execute command and the control relays are
 RUN/FAIL LED indicator operated. Pulse output controls are automatically
 Module operating condition available as the RTU timed and independently checked.
database point
 Configurable output types (latch, variable pulse, 8 Channel Digital Output Module
trip/close pairs, raise/lower pairs, and multiple The 8 Channel Digital Output 10A Module provides
relays) high current AC and DC control outputs at voltages
 High security control output logic with two pass up to 129V dc and 110 Vac. High switching capacity
‘check before operate’ relays are used to provide long contact life while
 Built-in hardware and software monitoring of controlling inductive loads up to 129 V dc nominal.
control operations
 PSS 31H-8K1
Page 5

Features For the 10A relay modules, the relays are mounted
Key features of 10A Digital Output Modules include: on the logic board. The plug-in terminal assembly
carries screw terminals for loop termination of heavy
 Eight independent single pole normally open
gauge wire.
digital outputs
 Two power relays in series provide high current
Multi Input/Output Module
DC inductive load break capacity
 Configurable output types (latch, variable pulse, The Multi I/O Module provides a cost effective
trip/close pairs, raise/lower pairs, and multiple solution for applications utilizing a combination of
relays setpoint) status inputs, analog inputs and control outputs.
 High security control output logic with two pass The Multi I/O Module combines the technology of the
‘check before operate’ and one-of-N check on Analog Digital Input Module and the 12 Digital Output
paired outputs Module within one module:
 Built-in hardware and software monitoring of  24 Digital Inputs
control operations  6 Analog Inputs
 Removable plug-connected termination  8 mini pilot relay or 6 paired pilot relay outputs.
assembly
Variants of the Multi I/O Module are:
 Control output duration is individually
configurable  129 V 8 Mini Pilot Relay
 Screw terminals for loop connection of up to 16  48 V 8 Mini Pilot Relay
gauge cable.  24 V 8 Mini Pilot Relay
 RUN/FAIL LED indicator  129 V 6 Paired Pilot Relay
 Module operating condition available as database  48 V 6 Paired Pilot Relay
point.  24 V 6 Paired Pilot Relay.

Module Description Features

The digital output subsystem provides security and Key features of the Multi I/O Module include:
control for electrical or magnetically latched relays.  Removable plug-connected termination
The Digital Output Modules consist of an on-board assembly
microprocessor and security circuits mounted on a  RUN/FAIL LED indicator
logic board. Configuration data from the main  Module operating conditions available as
processor (COPE) determines the control of each database points
output relay by the on-board processor.
PSS 31H-8K1
Page 6

 Digital Inputs

• 24 software configurable digital inputs

• Individually configurable chatter filters
• Digital input bounce elimination circuitry
• Optical isolation on digital inputs
• Digital input common may be positive or
negative
 Analog Inputs

• 6 analog inputs
• Plug-in current loop resistors
• 12 bits plus sign analog-to-digital converter
• ±2 V range
• Continuous automatic input
calibration/check
 Control Outputs

• 8 mini pilot relays or 6 paired pilot relays

• Configurable output types (latch, variable
pulse, trip/close pairs, raise/lower pairs, and
multiple relays)
• Built-in hardware and software monitoring of
control operations
• High security control output logic with two
pass ‘check before operate’
 Control output duration is individually
configurable.
Figure 1. Multi I/O Module
 PSS 31H-8K1
Page 7

Digital Inputs Two-Pass Operation

This subsystem optically isolates, filters, protects During pass 1, the on-board microprocessor accepts
against surge transients, and processes 24 status command data from the main processor (COPE). The
inputs. Digital input circuits rejects contact noise by validity of the command is confirmed and then the
use of contact debounce circuitry. Processing by the hardware is checked on the output driver circuits. If
on-board microprocessor allows identification of tests succeed, feedback of the command is sent to
chattering contacts. the main processor.
The digital inputs share a pair of common terminals, During pass 2, the main processor (COPE) sends the
which may be connected to positive or negative execute command and the control relays are
supply. operated. Pulse output controls are automatically
Digital inputs status is provided by scanning every timed and independently checked.
millisecond. Sequence of Events with one millisecond
resolution time-tagging is available. 20 Channel Analog Input Module
The Analog Input Module provides a cost effective
In addition, each of the digital inputs supports
method for gathering a large volume of analog
accumulator and Momentary Change Detection
information from the field. The 20 Channel Analog
functionality.
Input Module provides accurate 12 bit plus sign
Analog Inputs resolution over wide temperature ranges. A 1 kV
The analog input circuitry within the Multi I/O Module isolation option provides individually isolated
performs the data sampling and processing for the channels.
analog input points. This subsystem provides
In the non-isolated module, calibration values of zero
protection against surge transients, high frequency
and full scale voltage reference are available as
noise, and mains frequency noise. A multiplexed
database points while the isolated module utilizes a
analog-to-digital converter provides high resolution
self-calibrating analog-to-digital converter.
and high-speed update of analog values.
Features
These values are stored in shared memory for access
Key features of Analog Input Modules include:
by the main processor (COPE) via the Electrobus
interface. Automatic zero drift correction is provided  20 analog inputs
by the on-board microprocessor. Zero and full-scale  12 bits plus sign analog-to-digital converter
voltage references are available as internal database  ±2 V ranges
points accessible by the SCADA Master Station.  RUN/FAIL LED indicator
 Plug-in current loop resistors
Digital Outputs
The digital output subsystem of the Multi I/O Module  Removable plug-connected termination
provides secure control for the digital outputs. Eight assembly.
mini pilot or six paired pilot relay options are
available.
Outputs may be driven as fixed or variable length
pulse, or may be electrically latched. Independent
source and sink drivers control each output relay.
PSS 31H-8K1
Page 8

4 Channel Analog Output Module Optical Isolation

The 4 Channel Analog Output Module provides four The digital-to-analog converters are serially linked to
isolated current outputs. Outputs of 4 to 20, 0 to 10 the rest of the module via optical isolators. Power is
and 0 to 16 mA are independently configurable. supplied from an external source, which results in an
electrically isolated interface to the external devices.
Two-pass operation with built-in hardware checking
ensures that reliable control of equipment is This design also sustains outputs, even in the event
maintained. Each analog output can be scaled of RTU or module failure, providing external loop
independently for the selected output current range power is maintained.
as part of the RTU database configuration. Internal Monitoring
Features Each channel has two internal alarm points
Key features of Analog Output Modules include: associated with it. If the external voltage source fails,
or the current loop is open circuit to the output, the
 Four channel analog output
on-board processor is notified via optically isolated
 12-bit resolution
digital inputs. These inputs are then passed to the
 4 to 20, 0 to 10, and 0 to 16 mA ranges
main processor (COPE) module, to be made
 Optical isolation of output circuits
available for scanning if required by the SCADA
 Internal monitoring of external voltage fail and
Master Station.
open circuit alarms
 Removable plug-connected termination An operator can be notified if an analog device has
assembly. been disconnected from the RTU, or if the external
voltage source has failed, enabling problems in the
field to be identified remotely.
 PSS 31H-8K1
Page 9

M U LT I I / O M O D U L E F U N C T I O N A L S P E C I F I C AT I O N S

Multi I/O Module Maximum Common Mode Voltage

24 Status Input, 6 Analog Input, 8 mini-pilot or 6 Operating within spec ±6 V
paired pilot relay. (24 V, 48 V, or 129 V) Without damage ±50 dc or peak ac
NUMBER OF CHANNELS Transient Protection
24 Status inputs IEEE C37.90-1
6 Analog field inputs IEC 60255 Class 3
2 Internal check analog inputs Impulse Voltage Withstand
8 Mini-pilot relay controls or 6 paired pilot relay Common mode 5 kV (input to ground)
Differential mode 5 kV (across input)
controls
High Frequency Disturbance
ANALOG INPUTS Common mode 2.5 kV (input to ground)
Input Circuit Differential mode 1 kV (across input)
6 differential inputs Fast Transient (IEC 61000-4-4)
Analog-to-Digital Converter Type 4 kV 5 kHz capacitively coupled
Sigma-Delta Reference Voltages
Resolution Zero volts and full scale positive (+1 V)
12 bits plus sign DIGITAL INPUTS
Input Update Rate (Data Age) Input Circuits
<600 ms 24 per input module
Input Signal Range Input Types
±2 V dc Any input can be used as: Status,
Input Signal Scaling Momentary Change Detect, Sequence of
Dropping resistor for current inputs Events, Accumulator
Full Scale Range Circuit Types
±4000 counts (over range ±4095 counts) Common return for all 24 inputs, positive or
Maximum Error at 25° C and 0 V Common negative
Model Input Voltage
±0.1% full scale 24 V, 48 V or 129 V dc from field supply
Common Mode Error Input Current
0.01% per Volt to a maximum of ±6 V 5 mA per input (nominal)
Temperature Error Transient Protection
0.0016% per ° C to over full temperature IEEE C37.90.1
IEC 60255 Class 3
range
Impulse Voltage Withstand
Maximum Error Over Temperature and
Common mode 5 kV (input to frame)
Common Mode Range Differential mode 5 kV (input to common)
±0.25% full scale High Frequency Disturbance
Differential Mode Rejection Common mode 2.5 kV (input to frame)
80 dB at 6 V peak, dc to 50/60 Hz balance Differential mode 1 kV (input to common)
input Fast Transient (IEC 61000-4-4)
Differential Mode Voltage Without Damage 4 kV 5 kHz capacitively coupled
±50 V dc or peak ac 2 kV 5 kHz direct injection
Common Mode Reject
60 dB minimum at 50/60 Hz
PSS 31H-8K1
Page 10

M ULT I I / O M O D U L E F U N C T I O N A L S P E C I F I C AT I O N S ( C O N T. )

Multi I/O Module (Continued) ISOLATION

CONTROL OUTPUTS 2 kV RMS for 1 minute output to frame
Output Types 1 kV RMS for 1 minute across open contact
Outputs can be configured as: Pulse, TRANSIENT PROTECTION
Trip/Close pairs, Raise/Lower pairs, single IEEE C37.90.1
Variable Pulse, Latched, or Set-point IEC 60255 Class 2
Security Impulse Voltage Withstand
One or more than one relay energized test Common mode 2.5 kV (output to frame)
check before execution of control Across output contact 1 kV
High Frequency Disturbance
Multi I/O Mini-Pilot Relay Termination
Common mode 1 kV (output to frame)
Assembly
Fast Transient (IEC 61000-4-4)
24 V dc, 48 V dc, or 129 V dc with 2 kV ac RMS
4 kV 5 kHz capacitively coupled
isolation to chassis for status inputs. Printed circuit
2 kV 5 kHz direct injection
assembly 261.8 mm x 35 mm attached to frame by
captive screws. Terminals sized for 1.5 mm2 wire. Multi I/O Paired-Pilot Relay Termination
ANALOG INPUTS Assembly
2 Terminals per point 24 V dc, 48 V dc, or 129 V dc with 2 kV ac RMS
Loop drop resistor mounted on rear side of isolation to chassis for status inputs. Printed circuit
terminal assembly assembly 261.8 mm x 35 mm attached to frame by
Suppression device to ground from each input screws. Terminals sized for 1.5 mm2 wire.
terminal ANALOG INPUTS
DIGITAL INPUTS 2 Terminals per point
24 status inputs Loop drop resistor and voltage divider
1 terminal per point terminals mounted on rear side of terminal
2 shared common terminals assembly.
Suppression device across each input to the Suppression device across each input to the
common common
MONITORS/INDICATORS DIGITAL INPUTS
Green/Red RUN/FAIL LED 24 status inputs
NUMBER OF RELAYS 1 terminal per point
Eight 2 common terminal
Suppression device across each input to its
RELAY COIL CURRENT
common
18 mA
MONITORS/INDICATORS
CONTACT ARRANGEMENT
Green/Red RUN/FAIL LED
8 single pole contacts and 1 common
NUMBER OF RELAYS
CONTACT RATING
Six in 3 pairs
0.5 A 125 V ac cos φ = 0.4 (30,000 operations)
D.C. make capacity RELAY COIL CURRENT
0.5 A 129 V dc (30,000 operations) 18 mA
D.C. break capacity
0.25 A 50 V dc L/R 40 ms (30,000 operations)
50 mA 129 V dc L/R 40 ms (30,000 operations)
 PSS 31H-8K1
Page 11

M ULT I I / O M O D U L E F U N C T I O N A L S P E C I F I C AT I O N S ( C O N T. )

Multi I/O Paired-Pilot Relay Termination ISOLATION

Assembly (Continued) 2 kV RMS for 1 minute output to frame
CONTACT ARRANGEMENT 1 kV RMS for 1 minute across open contact
Contacts arranged as pairs of single pole TRANSIENT PROTECTION
contacts sharing a common IEEE C37.90.1
CONTACT RATING IEC 60255 Class 3
5 A 250 V ac cos φ = 0.4 (30,000 operations) Impulse Voltage Withstand
D.C. make capacity Common mode 5 kV (output to frame)
5 A 129 V dc (30,000 operations) Across output contact 1 kV
D.C. break capacity High Frequency Disturbance
0.5 A 50 V dc L/R 40 ms (30,000 operations) Common mode 2.5 kV (output to frame)
200 mA 129 V dc L/R 40 ms (30,000 Fast Transient (IEC 61000-4-4)
operations) 4 kV 5 kHz capacitively coupled
2 kV 5 kHz direct injection

PRODUCT SAFETY
This product complies with the U.S. Standard for Safety UL 61010-1 - Safety requirements for electrical
equipment for measurement, control, and laboratory use - PART 1: GENERAL REQUIREMENTS - Edition 2 -
Revision Date 2008/10/28 and CSA C22.2 NO. 61010-1 - Safety requirements for Electrical equipment for
measurement, control, and laboratory use.
PSS 31H-8K1
Page 12

2 0 C H A N N E L A N A L O G I N P U T M O D U L E ( I S O L AT E D ) F U N C T I O N A L S P E C I F I C AT I O N S

20 Channel Analog Module (1 kV Isolated) Differential Mode Voltage Without Damage

20 Analog Input ±24 V dc or peak ac
NUMBER OF CHANNELS Common Mode Rejection
20 Analog field inputs 120 dB at 1000 V ac, dc to 60 Hz balanced
2 Internal check analog inputs input
ANALOG INPUTS Maximum Common Mode Voltage
Input Circuit Operating within spec 1000 V ac RMS
20 separately isolated analog inputs Transient Protection
Analog-to-digital Converter Type IEEE C37.90.1
Sigma Delta IEC 60255 Class 3
Impulse Voltage Withstand
Resolution
Common mode 2 kV (input to ground)
12 bits plus sign
Differential mode 0.5 kV (across input)
Input Update Rate (Data Age) High Frequency Disturbance
<600 ms includes calibration cycle Common mode 1 kV (input to ground)
Input Signal Range Fast Transient (IEC 61000-4-4)
±2 V dc 4 kV 5 kHz capacitively coupled
Input Signal Scaling Reference Voltages
Current loop resistor Auto calibration on individual channels does
Full Scale Range not require external check voltages.
±4000 counts (over range ±4095 counts) 20 Channel Analog Terminal Assembly
Maximum Error at 25° C PRINTED CIRCUIT BOARD
±0.1% full scale 261.8 mm x 35 mm attached to frame by
Common Mode Error screws.Terminals sized for 1.5 mm2 wire
0.0001% per Volt to a maximum of
TERMINALS
1000 V ac (120 dB)
2 Terminals per point
Temperature Error 1 chassis terminal per four input channels
0.002% per ° C Loop drop resistor mounted on rear side of
Maximum Error Over Temperature and terminal board.
Common Mode Range MONITORS/INDICATORS
±0.25% full scale Green/Red RUN/FAIL LED
Differential Mode Rejection
60 dB minimum at 60 Hz

PRODUCT SAFETY
This product complies with the U.S. Standard for Safety UL 61010-1 - Safety requirements for electrical
equipment for measurement, control, and laboratory use - PART 1: GENERAL REQUIREMENTS - Edition 2 -
Revision Date 2008/10/28 and CSA C22.2 NO. 61010-1 - Safety requirements for Electrical equipment for
measurement, control, and laboratory use.
 PSS 31H-8K1
Page 13

A NA L O G / D I GI TAL I N P U T M OD U L E F UN C T I O N AL S PE CI F I CAT I ON S

4 Analog/32 Digital Input Module (1 kV ANALOG INPUTS (CONT.)

Isolated) Reference Voltages
NUMBER OF CHANNELS Auto Calibration on individual channels does
4 Analog field inputs not require external check voltages
32 Status inputs Transient Protection
ANALOG INPUTS IEEE C37.90.1
IEC 60255 Class 2
Input Circuit
Impulse Voltage Withstand
4 differential inputs per input module
Common mode 2 kV (input to ground)
Analog-to-Digital Converter Type Differential mode 1 kV (across input)
Sigma Delta High Frequency Disturbance
Analog-to-Digital Conversion Time Common mode 1 kV (input to ground)
20ms Differential mode 0.5 kV (across input)
Resolution Fast Transient (IEC 61000-4-4)
12 bits plus sign 4 kV 5 kHz capacitively coupled
Input Update Rate (Data Age) DIGITAL INPUTS
20 ms Input Circuits
Input Signal Range 32 per input module in 4 groups of 8 inputs
±2 V dc Input Types
Input Signal Scaling Any input can be used as: Status,
Dropping resistor for current inputs or Momentary Change Detect, Sequence of
voltage Events, Accumulator (1 or 2 inputs per
Full Scale Range accumulator)
±4000 counts (over range ±4095 counts) Circuit Types
Maximum Error at 25° C and 0 V Common Common return per group of 8 inputs
Mode Common positive or common negative
±0.1% full scale Input Voltage
Common Mode Error 24 V to 129 V, selected individually per input
0.0001% per Volt to a maximum of 1000 V by jumper setting; factory default range is
ac (120 dB) 48-129 V; field configurable to 24-48 V.
Temperature Error Input Current
0.002% per ° C over temperature range 5 mA per input (nominal)
Isolation Type
Maximum Error Over Temperature and
Opto-coupler
Common Mode Range
±0.25% full scale Insulation
2 kV RMS for 1 minute input to frame
Differential Mode Rejection
(ground)
60 dB minimum at 50/60 Hz
Transient Protection
Differential Mode Voltage Without Damage
IEEE C37.90.1
±24 V dc or peak ac
IEC 60255 Class 3
Common Mode Rejection
Impulse Voltage Withstand
120 dB at 1000 Vac, dc to 60 Hz balanced
Common mode 5 kV (input to frame)
input Differential mode 5 kV (input to common)
Maximum Common Mode Voltage High Frequency Disturbance
Operating within spec 1000 V ac
PSS 31H-8K1
Page 14

A N A L O G /D I G I TA L I N P U T M O D U L E F U N C T I O N A L S P E C I F I C AT I O N S ( C O N T I N U E D )

DIGITAL INPUTS (CONT.)

Common mode 2.5 kV (input to ground)
Differential mode 1 kV (input to
common)
Fast Transient (IEC 61000-4-4)
4 kV 5 kHz capacitively coupled
2 kV 5 kHz direct injection

PRODUCT SAFETY
This product complies with the U.S. Standard for Safety UL 61010-1 - Safety requirements for electrical
equipment for measurement, control, and laboratory use - PART 1: GENERAL REQUIREMENTS - Edition 2 -
Revision Date 2008/10/28 and CSA C22.2 NO. 61010-1 - Safety requirements for Electrical equipment for
measurement, control, and laboratory use.
 PSS 31H-8K1
Page 15

1 2 C H A N N E L D I G I TAL O U T P U T M OD U L E S F U N C T I O N A L S P E C I F I C AT I O N S

12 Channel Digital Output Modules Magnetically Latched Relay Output Module

Pilot or Magnetically Latched Relay NUMBER OF RELAYS
NUMBER OF CHANNELS Twelve
Twelve RELAY TYPE
OUTPUT TYPES Latching
Outputs can be configured as: Level, Pulse, RELAY COIL CURRENT
Trip/Close (in pairs), Raise/Lower (in pairs), 27 mA while latching
Latching CONTACT ARRANGEMENT
SECURITY Two-pole N/O relays with contacts connected in
One or more than one relay energized test series to boost dc rating (output is single pole)
Pilot Relay Output Module CONTACT RATING
NUMBER OF RELAYS 5 A 250 V ac cos φ = 0.4 (30,000 operations)
Twelve D.C. make capacity
5 A 129 V dc (30,000 operations)
RELAY COIL CURRENT
D.C. break capacity
27 mA
1 A 50 V dc L/R 40 ms (30,000 operations)
CONTACT ARRANGEMENT 200 mA 129 V dc L/R 40 ms (30,000
Two-pole N/O relays with contacts connected in operations)
series to boost dc rating (output is single pole)
ISOLATION
CONTACT RATING
2 kV RMS for 1 minute output to frame
5 A 250 V ac cos φ = 0.4 (30,000 operations)
1 kV RMS for 1 minute across open contact
D.C. make capacity
2 kV RMS for 1 minute between outputs
5 A 129 V dc (30,000 operations)
TRANSIENT PROTECTION
D.C. break capacity
IEEE C37.90.1
1 A 50 V dc L/R 40 ms (30,000 operations)
IEC 60255 Class 3
200 mA 129 V dc L/R 40 ms (30,000
operations) Impulse Voltage Withstand
Common mode 5 kV (output to frame)
ISOLATION
Across open contact 2.5 kV
2 kV RMS for 1 minute output to frame
High Frequency Disturbance
1 kV RMS for 1 minute across open contact
Common mode 2.5 kV (output to frame)
2 kV RMS for 1 minute between outputs
Between outputs 2.5 kV
TRANSIENT PROTECTION
Fast Transient (IEC 61000-4-4)
IEEE C37.90.1
4 kV 5 kHz capacitively coupled
IEC 60255 Class 3
2 kV 5 kHz direct injection
Impulse Voltage Withstand
Common mode 5 kV (output to frame) Control Output Termination Assembly
Across output contact 2.5 kV Printed circuit board 261.8 mm x 35 mm attached to
High Frequency Disturbance frame by screws
Common mode 2.5 kV (output to frame) TERMINALS
Between outputs 2.5 kV Two terminals per relay. Terminals sized for
Fast Transient (IEC 61000-4-4) 1.5 mm2 wire.
4 kV 5 kHz capacitively coupled MONITORS/INDICATORS
2 kV 5 kHz direct injection Green/Red RUN/FAIL LED
PSS 31H-8K1
Page 16

8 C H A NN E L DI GI TAL O UT P U T M O D U L E S F U N CT I ON A L S PE CI F I CAT I O N S

8 Channel Digital Output 10A Module ISOLATION

Heavy Duty non-latched Relay 2 kV rms for 1 minute output to frame
NUMBER OF CHANNELS 1 kV rms for 1 minute across open contact
Eight 2 kV rms for 1 minute between outputs
OUTPUT TYPES TRANSIENT PROTECTION
Outputs can be configured as: Level, Pulse, IEEE C37.90.1
Trip/Close (in pairs), Raise/Lower (in pairs), IEC 60255 Class 3
Latching Impulse Voltage Withstand
Common mode 5 kV (output to frame)
SECURITY
Between outputs 5 KV
One or more than one relay energized test
High Frequency Disturbance
NUMBER OF RELAYS Common mode 2.5 kV (output to frame)
Sixteen single pole N/O relays with contacts Between outputs 2.5 kV
connected in series to boost dc rating Fast Transient (IEC 61000-4-4)
RELAY COIL CURRENT 4 kV 5 kHz capacitively coupled
75 mA for two coils associated with each output 2 kV 5 kHz direct injection
CONTACT ARRANGEMENT CONTROL OUTPUT TERMINATION ASSEMBLY
Output is single pole normally open Printed circuit board 261.8 mm x 35 mm
CONTACT RATING attached to frame by screws
16A at 250 V ac Resistive, 85°C 30,000 TERMINALS
Operations Two terminals per relay. Plastic encased wire loop
10A at 250 V ac Resistive, 105°C 100,000 screw terminals sized for 2.5 mm2 (16 AWG)
Operations wire.
10A at 400 V ac Resistive, 105°C 100,000 MONITORS/INDICATORS
Operations Green/Red RUN/FAIL LED
 PSS 31H-8K1
Page 17

4 C H A N N E L A N A L O G O U T PU T M O D U L E F U N C T I O N A L S P E C I F I C AT I O N S

4 Channel Analog Output Module EXTERNAL LOOP POWER

CHANNELS 24 V (maximum 36 V, minimum 19 V)
Four LOOP LOAD RESISTANCE
OUTPUTS 0 ohms minimum, 600 ohms maximum
Each output is configurable: TRANSIENT PROTECTION
IEEE C37.90.1
IEC 60255 Class 3
Output
Impulse Voltage Withstand
Range Counts Steps
Common mode 5 kV (output to frame)
4 to 20 mA 0 to 4000 4000 Across open contact 2.5 kV
High Frequency Disturbance
4 to 20 mA 800 to 4000 3200 Common mode 2.5 kV (output to frame)
0 to 10 mA 0 to 4000 2560 Between outputs 2.5 kV
Fast Transient (IEC 61000-4-4)
0 to 16 mA 0 to 4000 4000 4 kV 5 kHz capacitively coupled
4 to 20 mA 0 to 2000 2000 CHANNEL ISOLATION
50 V dc channel to chassis
4 to 20 mA 400 to 2000 1600 50 V dc channel to channel
0 to 10 mA 0 to 2000 1280 4 Channel Analog Output Termination
0 to 16 mA 0 to 2000 2000
Assembly
261.8 mm x 35 mm attached to frame by screws
NOTE TERMINALS
Where the count range is greater than the Four terminal blocks
number of output steps, some changes in
counts may not result in a corresponding Terminal 1 + Loop power
step change. Terminal 2 Loop power common
ACCURACY (4 TO 20 MA) Terminal 3 +I (current out)
±0.1% full scale at 25°C
±0.25% full scale over temperature range Terminal 4 –I (current return)
ACCURACY (0 TO 16 MA)
±1% full scale over temperature range
MONITORS/INDICATORS
Green/Red RUN/FAIL LED

PRODUCT SAFETY
This product complies with the U.S. Standard for Safety UL 61010-1 - Safety requirements for electrical
equipment for measurement, control, and laboratory use - PART 1: GENERAL REQUIREMENTS - Edition 2 -
Revision Date 2008/10/28 and CSA C22.2 NO. 61010-1 - Safety requirements for Electrical equipment for
measurement, control, and laboratory use.
PSS 31H-8K1
Page 18

P H Y S I C A L S P E C I F I C AT I O N S

Input/Output Modules share the same physical and (Electrobus) via a DIN 41612 connector and are
environmental specifications. double Eurocard size (233.4 mm x 149 mm). DIN
Physical Size 41612 connectors are also fitted to the front edge of
the PCB to provide connection to the terminal board
Each plug-in module requires frame space of 35 mm.
assembly.
Modules are assemblies of one or more printed circuit
boards. These modules plug into a backplane

E N V I R O N M E N TA L S P E C I F I C AT I O N S

Operating Temperature
STANDARD
0°C to +60°C (32°F to 140°F)
Humidity
10 to 95% (non-condensing)

O R D E R I N G I N F O R M AT I O N

Part Number Description

Multiple I/O Modules

SY-0399095 Multi Input Output Module 129 V 8 Mini Pilot Relay

SY-0399094 Multi Input Output Module 48 V 8 Mini Pilot Relay
SY-0399088 Multi Input Output Module 24 V 8 Mini Pilot Relay
SY-0399097 Multi Input Output Module 129 V 6 Paired Pilot Relay
SY-0399096 Multi Input Output Module 48 V 6 Paired Pilot Relay
SY-0399089 Multi Input Output Module 24 V 6 Paired Pilot Relay

Analog Input Module

SY-0399085 20 Channel Analog Input Module (Isolated)

Analog/Digital Input Module

SY-0399160 4 Analog/32 Digital Input Module (24 V to 129 V)

SY-0399222 4 Isolated Analog Inputs and 32 Digital Inputs (Deep Wiring Channel) Module

Digital Output Modules

SY-0399086 12 Pilot Relay Digital Output Module

 PSS 31H-8K1
Page 19

Part Number Description

SY-0399087 12 Magnetically Latched Relay Digital Output Module

SY-0399136 8 Digital Output 10 Amp Module

Analog Output Module

SY-0399084 4 Channel Analog Output Module

PSS 31H-8K1
Page 20

Invensys Systems, Inc Copyright 2015 Invensys Systems, Inc.

10900 Equity Drive All rights reserved.
Houston, TX 77041 Invensys is now part of Schneider Electric.
United States of America
http://www.invensys.com Schneider Electric, Invensys, Foxboro, Foxboro Evo,
FoxCom, and I/A Series, are trademarks owned by
Schneider Electric SE, its subsidiaries and affiliates.
Global Customer Support All other trademarks are the property of their respective
Inside U.S.: 1-866-746-6477 owners.
Outside U.S.: 1-508-549-2424
Website: https://support.ips.invensys.com MB 031 0315