SB 10060732 2280
SB 10060732 2280
SB 10060732 2280
Service
Category Vehicle Interior
Toyota Supports ~
ASE Certification -
Section Theft Deterrent/Keyless Entry Market USA
Applicability
REVISION NOTICE
SUPERSESSION NOTICE
• Applicability has been updated to include 1998 - 2015 applicable model year vehicles.
Service Bulletin No. SS003-01 is Obsolete and any printed versions should be discarded. Be sure
to review the entire content of this bulletin before proceeding .
Introduction
The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all
master keys are lost. Once the system is reset , all previously registered keys will be erased . Follow
the procedures in this bulletin to reset a vehicle Immobilizer or Smart Key system .
NOTE
There are new security provisions required to obtain a Reset Pass-Code. It is critical that the
instructions for this new process are reviewed BEFORE attempting to get a Pass-Code in the
new system.
Warranty Information
* Essential SST.
NOTE
• Only ONE of the Techstream units listed above is required .
• Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at
1-800-368-6787.
1. Review the veh icle application chart in the Techn ical Information System (TIS) to verify the
vehicle is capable of being reset.
Refer to the Toyota I Scion Vehicle Support chart located on TIS , under Diagnostics -
Immobilizer Reset - Reference Documents.
2. Review the new security authorization process and chose the option that best supports your
dea ler situation .
3. Follow the Techstream and TIS screenshots to obta in the Pass-Code needed to open registration
for Immobilizer and Smart Key programming .
NOTE
Some early ECM based Immobilizers cannot be reset using Techstream. For these vehicles , do
the following:
• Identify the vehicle using the Toyota I Scion Vehicle Support noted above.
An improved security measure has been implemented in TIS that requires a secondary approval by
dealer management each time an Immobilizer or Smart Key Reset request is submitted . Please
review the following flow chart and become familiar with the options outlined prior to attempting
a vehicle reset.
Figure 1. Immobilizer Reset Process
RE QUESTOR
APPROVING MANAGER
Steps introduced
July 5, 20 14
Key Points :
• The Reset request can be submitted from the Techstream in the vehicle, or on TIS before the
vehicle is available.
• A single management approval can be used multiple times for the same VIN as needed until the
vehicle repair is completed.
• Each Reset attempt for the same VIN will generate a new Seed Number and a unique
Pass-Code .
• The request and approval hand-off between technician and management is done on the TIS
home page inbox accessed at each individual's location (Techstream , office, etc .).
Main Steps :
1. Obtain Authorization
Variations:
2. Request and receive approval from Techstream after entering the reset utility
3. Repeated reset attempts with Techstream by accessing the single approval file
Approving Managers:
Once the Pass-Code Request form has been completed an approval request will be sent to all
approving managers. Dealership personnel with the following job titles in "Staffmaster" are granted
Pass-Code approval capability.
Dealer Principal, General Manager, Service Manager, Service Director, Service/Parts Director, Parts
Manager, Parts Director, Customer Relations Manager, Customer Satisfaction Manager, Shop Foreman,
Diagnostic Specialist, Team Leader Each dealer must have at least 2 enrolled managers in order to access
any Pass-Codes.
NOTE
Once a Reset is completed, it may be necessary to enter an "Immobilizer Key Registration" or a
"Smart Key Code Registration" utility to program the new keys. Early Immobilizer systems may be
ready to accept keys immediately after the Reset if the security light flashes a 2-digit code (such
as 21 or 22). Refer to the applicable Repair Manual for details.
Please review the Techstream and TIS screenshots in this bulletin to become familiar with the
new management authorization process flow.
1. Open TIS and enter the Diagnostics and Immobilizer Reset tabs. Login using your password.
Figure 2.
Key Co de Reset
Receiv e a Passcode
Immobi lizer and Smart Ke y Code Reset al lows the registration of a new Master
Key even if all original Ma ster Keys. are lost. Once the Immobilizer and/or Smart
Key Code is reset, all prev iously registered k ey codes wi ll be erased.
Re-enter your Password below to proceed to the Immobilizer and Smart Key Code
Reset form .
Password : l~-----~I
2. Enter the information requested , check all 4 boxes below Positive Identification Policy, then
click Next.
Figure 3.
~ ~ ~ .
0 l..ibrary ~ 0 Tech Assistance 0
Ke y Code Reset
Dealer Code :
Dealer Name:
Technician Name:
~
* Repair Order/ Parts Invoice Number:
~------~
• customer Last Name:
~------~
I •.., rI I have venfied the customer's authority to obtain vehicle security information for this vehicle .
I have venfied the customer's full legal name and confirmed the ir identity with a valid picture lD .
*r I have or will visually confirm the vehicle's registration document and ownership .
•r I agree to the TIS Terms and Conditions .
~ Details of this t ransaction w ill be included in the Monthly Vehicle Security Transactron Report sent t o the Dealer GM . Also, a log
of each tra nsaction is sent t o the National rnsurance Crime Bureau.
3. A minimum of two managers are required to be selected . Once two or more managers are
selected , click Submit to continue. Each request is required to be approved by one manager.
Once manager approval is received , continue to Section 5, "Receipt of Pass-Code."
Figure 4.
Select a minimum of two managers from the list betow and click Submit to
continue. Each request requires approval from one manager.
Examp le Manager 1 D
Example Manager 2 D
Exam ple Manager 3 D
Exam ple Manage r 4 ~
Example Manager 5 ~
------~---'
MW.Ebif
**I+*
"i'*+H'
'jfW':!!.1·"
Efbii+!,!.111
--
C;Qn.i.Z
'
2. Choose the appropriate vehicle model and year if the ignition cannot be turned on and the
information does not automatically populate .
Figure 6.
jTOYOTA ::J
I ,..
Hilux
..... Land Cruiser
Matrix
MR2
MR2 Spyder
Paseo
Previa
Prius
Prius C
!
'"' Prius PHV
Prius V
*ff$* Rav4
Rav4 EV ,,
I
Systom S.loct S1ora.1 Dr.a I
System Selection Menu
Se~t de1i111d syseom and 1hen press the am:iw t>u11cn 10 access the ECU
~ Y ellow• ecu 11.JtU9trimoy,n
..
~Whit1 • ECU co~1onOK
J "Syslem I Wl'ldf! WIA!l flfillk .. E CU not !Wppor1ed or ool 1espoodlng
"!iiil+'*
•mi.r• All ECU1
~"9
f'MPS
P1e-Coi;Sl(;n
P Ooor 'Aot:r
j PowertrHI
rt .id E:.:.:T
I Cha.uis J Body Electncal f
H,-broi C(n~cl
L1t11t k.ttpn"J ~~SI
Pre-Cc4s:O!\ 2
Rt 0001 t.lc1cr
W1J1·Cru1!01
Transm 51Kll\ CCll!ffll
Marn Bod't
RRlloofr.t3Cc.r
ACS\/~rw.c
As CondllClK'I'
PM1 Gal!Wr/
l,Wtt1 S·Mtch
r... i.-ru11U"•f.bntcr
S~Airto119
0-0eGl '•IGICW
5~J.n.J Hool I
Ccmtw1r.1on 1,•,.1"' Hl Autnle-.91wig ~6§$l!l!JllC!2:1Jf• • • IPGYo'ti SourN! Cootrol' o--~ r D•tKt~,r
R~e En?nt Star1tr tb".tp.;n S -surr l'IJ.f2 fJ a:tv.a T<'Tlallu I
MWNM
we
+!Mfk+
.....
CU51oml7e Comrn11mcatum Ched.(Kf!y Dutg MOde)
ECU Communicalion ID Reg1111rat100 ~~Code E1asuia
<lnll.xlut11on:>
Th1:'.I ~nc:l 1on erns~ all reg1ateu1d Smart Codo::i In orrler lo use lhis funchon you oocd a pa9!1Wt1td For lhe det:uls soe lhe rep;m m:1t1u.J! or
th&Scfl.ltoBullnhn
**S+'M 111¢1
5. Enter the VIN if prompted .
Figure 9.
Ctl!;ICO'HZO
ECU Commun1tah Input VIN .
Sm3!1CDcleReq1s
Input
""""'""
lr..c th13 fu nc11on l
Mrf•iG#&.ii.+
<introducuon>
Thisf\mcT1on eras
the S&MCe Bul1eli
< Back II rJ. <t the de!ails see thi! 1epalf manual~
MUIW
**31.§M
CustOO"IZ"e
ECU ConYT1un1C:il. Step 1 Of 2
'*W $mist Coda Regis.
Seed Number:
aa910aca2oso9sb9a015943c6
97037521dledllfc5b177c0cb Get
7f0cd395b05Z4bd1063eed58e Pass-Code
5dbd98a5fcd4bde1763e3
Pass-Code Number:
Input
.,
••at+•
+;;1u+
.. <ln'Jocfac11on>
Thi9fu11clion aras
theSer."K.:e8ullflt1
< Back the detai:a !HK! rhe r11pa1r manual ;)!'
*Bi*
*Sb'*
Sm,ut C..od1• RPwt
aa910acd208095b9d015943c6
9703 752ldledllfc5bl77c0cb
7f0cd395b0524bdl063eed58e
Sdbd98a5fcd4bdel763e3
....z> Press "Send" to send the Seed Number
to the Smart Code Reset webpage.
*·i!'li* Press "Copy" to copy the Seed Number
to the Clipboard
~ Send ,i Copy
c:.1.JsagtP
Usethi:ifur.c t1011 t
<lnlroduci(()fl>
Thnfunc:t1onetas < Back Exit the~adsse!?the~p;urmanu31or
µ.
ee;ga+
NOTE
• If there is already a management approval file for this VIN, DO NOT follow the next 3 steps to
resubmit a request. Open the approval file in your TIS inbox and enter the most recent Seed
Number to get the Pass-Code (as outlined in Section 5, "Receipt of Pass-Code'). Then go to
Section 6, " Techstream Reset Utility (Reset Initiated)."
• For repeated Reset attempts after the approval is completed , follow Sect ion 3, " Techstream
Reset Utility (With Request)," and Section 6, " Techstream Reset Utility (Reset Initiated)," using
the same management approval file.
I mmobittzer Reset
Ke y Cod e Reset
Receive a Pa ssco de
Immobilizer and Smart Key Code Reset allows the re gistration of a new Master
Key ev en if all original Master Keys are lost. Once the Immobilizer and/or Smart
Key Co de is reset, all previousl y registered key codes will be erased .
Re -enter your Password below to proceed to the Immobi lizer and Smart Key Code
Reset form .
Password: I I
lc lead ILogi nl
0
O Tech Assktance O Vcbrck! Inquiry
1
"C-!!V Cod• ' 7ef~m•~ I Na'l•Qaton
Dealer Code:
Dealer Name:
Technician Name:
~Detail s of this transaction w1H be included m the Monthly Vehicle Security lransadion Report sent to the Dealer GM. Also, a log of each transaction is
sent tn the Na tional [llSurance Crime Bureau .
10. A minimum of two managers are required to be selected. Once two or more managers are
selected , click Submit to continue . Each request is required to be approved by one manager.
Once manager approval is received , continue to Section 5, "Receipt of Pass-Code."
Figure 14.
Select a minimum of two managers from the list below and click Submit to
continue. Each request requires approval from one manager.
Exam ple Manager 1 0
Exam ple Manager 2 0
Example Manager 3 0
Exam ple Manager 4 ~
Example Manager 5 ~
'
ISubmiij leancell
1. Once the request has been submitted , one of the authorized dealer managers will locate the
technician 's request in their TIS home page inbox.
r !
0613012014 · - w4th
r !
06/30/2014 naw etherdfhgr
r 06/3012014 ! ·- horq
r 06/ 29/201 4 ne., Approval Required : Key Cod~ Request No. 14062900025
r ! ...., dfvdfgdrv
06/2912014
~Y ~rtlficatlon 1
Name:
Primary Job Cod e :
2. The manager checks the 3 boxes under Request Approval Policy, then selects Approve to
send the approval to the technician .
Fi gure 16.
Service lane
it Inbox
Subject: Approval Required: Immobilizer Rese t Request No . 1407010002 1
J
l Hello
T he user has requested t o perform an Immobilizer Reset on 07/01/2014 01:27 PM PDT. The
I details of..th
' - e-re
_ q_u_e_s_t -a-r e- a
- s""'ro
""11-o w
- s,
1. Once approved by management , the technician opens his TIS inbox and locates the Reset
request. The technician clicks the title to open the Approval.
Figure 17.
r 06/23/201 4- ! n• w dfgd
r !
OG/23}2014 now dfgdf
My Ce rtification s
Na 1ne :
P ri m a ry Jo b Co d e :
Cu rren t Certifica ti o n Sta tu s:
University of Toyota
NOTE
• It is recommended to retrieve the Pass-Code from the Techstream connected to the vehicle
as the Seed Number and Pass-Code work together.
• Once approved by management, multiple resets can be performed for a single VIN.
Each attempt will create a new Seed Number and resultant Pass-Code.
2. Once opened , the technician clicks the Immobilizer Reset link to continue.
Figure 18.
Jnbcx
1Su b ject: Immobilizer Reset Request No. 14053000028 has been Approved
You had 1mbated a request (Request No. 14063000028) f'or an Immob1l1zer Reset on 06/30/2014 03:09 P~ POT. Your request has been Approved and details
I1have been saved.
Request Details:
I Request No:
I Dealer Code:
i Dealer Name:
Technician Name:
I
1
Vehicle VIN:
Repa ir Order/ Pa rts Jn..,oice Number:
! Customer Last Name :
Manager:
I
1
...... . Approval Date:
~ Please click on the link below to generate a new I mmobilizer Passrode fOf' your request. After clicking on this link, you will need to connect the Techstream
' · generate the Seed No. and enter th~ Techstream Soft ware Yers1on to proceed.
Immobihzcr Reset
l1nbox Home!
J
This link wi ll expire 1 hours after the receipt of this message at 06/30/201.4 04:20 PM PDT. This link may be used multiple t imes to perform an lmmobthzer
Reset for the menti oned VIN numbe r till rt expires.
~ertificati~
N a m e:
Pr ima ry J o b Code::
Current Certifica tion S t a tu s:
UnNers1ty of Toyota
3. At this point, it is necessary for the technician to re-enter their password to login again .
Figure 19.
~ Code Reset
Receive a Passcode
Immobilizer and Smart Key Code Reset allows the registration of a new Master Key even 1f all origmal Master Keys are lost. Once the I mmobilizer and/ or Smart
Key Code is rese:t, all previously reoi~ered key codes will be erased.
Re·enter your Password below to proceed to t.he l mmob1!izer and Smart Key Code Reset form.
P~sswor d :
~------~
4. The technician must enter the Techstream software version and paste in the Seed Number
from Techstream , then click Next.
Figure 20.
K e y Cod e Reset
R.equest ,...o
Dealer Code :
Oealer Name ~
Techrnoan Name:
Vehicle VIN:
Repllir Order/Parts Jnvo1ce: Numbt!f:
Custome r Last Name:
Tech!::trearn Soft<Nare version ~-------.
"'Seed Number
(from Jeantcol) · ~------~
Pos jt jye Id c n U fic p Uon Po li cy
fV J have ve nfied the custom ers authority to obtam vehicle secUnt'{ tnformat1on fer this ve hicle .
JV I h a ve vcrtfie d t he cu:ttorn er's fu ll legol n.:ime and CO!lfirmed the ir identi ty with va lid picture 10
rv I hav e or will visuall y confi nn the vehicle's reg1strat1 cn document and owners.hip.
P I egree to tt'le Terms and Conditions .
.Ms2.b:.;, Details of this transaction will be included 1n the ,..lonthlv Vet11de Security Transactt0n Repo rt sent 10 the Dealer GM Al~o . " log of each trens;,ct1cn l!O
sent to t he Nauonal Insu rance Crime Bureau .
5. The Pass-Code will then be provided as shown . Continue to Section 6, "Techstream Reset Utility
(Reset Initiated)," for instructions on entering the Pass-Code to initiate the Reset.
Figure 21 .
Ke y Cod e Reset
Re qu est De t ai ls
Requ est No:
Dealer Code:
Dealer Name :
Technician Nam e:
Vehide VTN:
Repai r Order/ Parts Invoice Num ber:
Customer Last Name:
Techstream Software Version:
Pos itiv e Id e nti ficat ion Policv
P' fn~~~a~e;~~~ i~~s ~e~~cTe~r's authority to obtain ve hicle security
,;; I have ve rifie d the custome r's full legal name and confirmed their identity
with a valid picture ID.
p I have or will visually co nfirm the ve hicle's registration document and
owne rship.
P' I agree to the TIS Terms and Conditions.
Re qu e st Aoorova l Policy
p- I ha ve ve rified the details entered for this request and confirmed the
authority of the custom e r was verified.
J;i I rea lize tha t _upon retrieva l, a transaction log will be
Insurance Cn me Bureau .
posteC, .e
Nati onal
The Reset can be initiated once the management approval reply is available in the TIS home page
inbox. With this approval file , multiple Seed Numbers can be used for as many attempts as needed
to repair the vehicle.
NOTE
If you have received the file from management in your TIS in box that shows the approval status
for the given VIN , do NOT resubmit for another approval for this vehicle. It will not be necessary.
Continue to open the approval file and enter a new Seed Number to get the unique Pass-Code
for each attempt.
1. After retrieving the Pass-Code from the manager approval process in Section 4 ("Manager
Approval') and Section 5 ("Receipt of Pass-Code"), enter the Pass-Code in Techstream and
click Next.
Figure 22.
'
Sy.ilt!m Sci.lei j Slomd O;ua SnllHI Key Uvc J
Cu11omi.z11 q Modc)
ECU Commt1n1e~· Step 1of2
Smltllemk.R ;
Seed Number:
aa910acd20809569d01594 3c6
,-
9703752ldledllfc5bl 77cOc b Get
7f0cd39Sb0524bdl063e e d58e Pass·Code
5dbd98a5fc bdel76 3e3
'1 Pass.Code Number:
,--,.,.--
- --1 1115474
-:Usage>
Input J t- - - - - - --
Un this func11on t
• ·BJM+
rjntroduct1on>
This fuociion en1
1tleSer.1Ce
< Back Next > I Exit I the details u& Iha repa11 manual °'
M#"IM
W3ffis+
., , ,.
+§NH
*iii'*
Customae
ECUCommU111Ca:1
Smarr Code Regi..
Step 1of 2
Yes ~, No
,..,-,-- --!
<Us •>
j 1154 74 Input
Use th1sfunthon l
<lnlroductmn>
Tius fuflclionllfiu < Back Next > Exit lhe dela1!1 1eethe repau manua/ 01
I theSer.'ICe Bul!ef
M§§IM
E!W
Figure 24.
Custormze
ECU Communteatt Step 2 of 2
*Si+ SmSr1 Cetta -
MEifi
*MU*
,.,,,,, NOW RESETTING
<CAUTION>
KEEP ORNER'S DOOR OPEN.
<Usage>
Useth1sftlnct1on t
..RM
Th;sl\Joction era!I 111M!detmlsseetherepairm11nual 01
theSelv.ceBulletJ
3. Once completed , it may be necessary to enter either the Immobilizer Key Registration or Smart
Code Registration utility to program keys.
Figure 25.
~~tmSe!«t j St"'9CIOiltii
"""""''Liv. I
Utlllty Select
5'1fctdtl5Qdl.tilt ....,
..,.
.....,,, CU'i!om1u
ECU Co11'lm1.111w::i1t•
9~~)
;
Sm"' 1 C ~Rflltl
( )
( J
I
I
-·
.
! ,~··
!"""""""'""'
<l11trodwc t1011~
Theb'ldlOllef~
tM Str.te• Bula.
r-Ex~
l lf thedetllhlffthete'pH~ Of
M@W
~
NOTE
Some early Immobilizer systems go directly into programm ing mode. This can be confirmed
by the security light blinking a 2-digit code. Refer to the applicable Repai r Manual for details.