Datos Tecnicos Motor Optra

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 4

xTooltipElement

Service Information
/si/home.do/si/home.do/si/publications.do/si/publications.do/si/numberSearchLink.do/si/
numberSearchLink.do/si/bulletinSearchLink.do/si/bulletinSearchLink.do/si/mainHelp.do/si/
mainHelp.do
2007 Chevrolet Optra | Optra, Viva (VIN J) Service Manual | Engine | Engine Mechanical - 1.8L
(LDA) | Specifications | Document ID: 1701367

Engine Mechanical Specifications

Specification

Application Metric English

Block

 Cylinder Bore Diameter 80 mm 3.1 in

 Cylinder Bore Out-of-Round -


0.0065 mm 0.0002 in
Maximum

 Cylinder Bore Taper - Maximum 0.0065 mm 0.0002 in

Camshaft

 Bearing Journal #1 OD 28.000-28.02 mm 1.1023-1.1031 in

 Camshaft Lobe Lift - Exhaust 8.0 mm 0.31 in

 Camshaft Lobe Lift - Intake 8.5 mm 0.334 in

Cooling System

 Capacity 7.5 L 7.9 qt

Crankshaft

 Connecting Rod Journal Diameter 42.971-42.987 mm 1.6917-1.6924 in

 Connecting Rod Journal Out-of-Round 0.004 mm 0.0001 in


 Crankshaft End Play 0.05-0.28 mm 0.002-0.011 in

 Crankshaft Main Bearing Clearance -


0.026-0.042 mm 0.001-0.002 in
All

 Crankshaft Main Journal Diameter 54.982-54.994 mm 2.164-2.165 in

 Crankshaft Main Journal Out-of-Round 0.004 mm 0.0001 in

Cylinder Head

 Minimum Overall Height After


135.63 mm 5.339 in
Machining

 Overall Height 135.63-136.23 mm 5.339-5.363 in

General Data

 Bore 80.5 mm 3.1 in

 Compression Ratio 9.5-9.9:1

 Displacement 1 796 cm³ 97.5 in³

 Engine Type F18D

 Firing Order 1-3-4-2

 RPO LDA

 Stroke 88.2 mm 3.47 in

Lubrication System

 Lubricating Type Forced Feed

Oil Pump

 Gap Between Oil Pump Body and Outer


0.40-0.484 mm 0.0157-0.019 in
Rotor

 Inner Rotor Side Clearance 0.035-0.085 mm 0.001-0.003 in

 Outer Rotor Side Clearance 0.45-0.10 mm 0.02-0.04 in

 Relief Valve Spring Free Length 81 mm 3.2 in

Pin
 Clearance: In Piston 0.010-0.020 mm 0.0003-0.0007 in

 Clearance: In Rod Interference Fit To Rod

 Length 55 mm 2.165 in

 Piston Pin Diameter 18.0 mm 0.708 in

 Piston Pin Offset 0.55-0.85 mm 0.02-0.03 in

Piston

 Clearance to Bore 0.020-0.040 mm 0.0008-0.0016 in

 Piston Diameter 80.465-80.475 mm 3.167-3.168 in

Piston Ring End Gap

 First Compression Ring 0.2-0.3 mm 0.008-0.012 in

 Second Ring Compression 0.4-0.6 mm 0.015-0.024 in

Piston Ring to Groove Clearance

 First Compression Ring 0.050-0.080 mm 0.002-0.003 in

 Second Compression Ring 0.050-0.082 mm 0.002-0.032 in

Sealants and Adhesives

 Camshaft Carrier to Cylinder Head HN 1581 - Loctite® 515

Anti-Seize Compound - HMC Spec HN


 Exhaust Manifold Studs/Nuts
1325

 Oil Gallery Plug HN 1256 - Loctite® 242

 Oil Pan Bolts HN 1256 - Loctite® 242

 Oil Pan Pickup Tube Bolts HN 1256 - Loctite® 242

 Oil Pump Bolts HN 1256 - Loctite® 242

 Rear Main Bearing Cap GE P/N RTV 159

Valve Springs

 Valve Spring Load - Closed 247-273 N @ 32 182-202 lb @ 1.25 in


mm

554-606 N @ 23
 Valve Spring Load - Open 409-447 lb @ 0.90 in
mm

Valves

 Valve Diameter - Exhaust 27.5 mm 1.08 in

 Valve Diameter - Intake 31.2 mm 1.22 in

 Valve Seat Width - Exhaust 1.4-1.8 mm 0.055-0.071 in

 Valve Seat Width - Intake 1.0-1.4 mm 0.039-0.055 in

 Valve Stem Diameter - Intake 6 mm 0.236 in

 Valve Stem Diameter - Exhaust 6 mm 0.236 in

Valve Guide Reaming Table

Size Reamer Production Code Service Code

Normal -- -- K

1.9 mm (0.075 in) KM-805 1 K1

3.8 mm (0.150 in) -- 2 K2

© 2021 General Motors Corporation. All rights reserved.

You might also like