Control Engineering

Course 2

1
Time-Domain Analysis of
Control Systems

2
 Overview
• Find and discuss transient and steady state time
response of a simple control system.
• Develop simple design criteria for manipulating
the time response.
• Look at the effects of adding a simple gain or
poles and zeros to the system transfer function
and relate them to the concept of control.
• Look at simple proportional, derivative, and
integral controller design concepts in time
domain.
3
Introduction
Steady-state response
• Time response:

Transient response

Typical Test Signals for the Time Response

4
 Ramp- and Parabolic-Function
Inputs
• Ramp-Function Input:

• Parabolic-Function Input:

5
The Unit-Step Response and
Time-Domain Specification

Steady-state error: r − yss

6
Steady-State Error

7
 Steady-State Error of Unity
Feedback
• Steady-state error:

H (s) = 1

• ess depends on the number of poles G(s) has at

8
 Unity Feedback with Step
Function Input
Step-function input: r (t ) = Ru s (t )  R( s) = R / s

9
 Unity Feedback with Ramp
Function Input
Ramp-function input:

R
ess =
Kv

10
 Unity Feedback with Parabolic
Function Input
Parabolic-function input:

11
Summary

12
Example

13
Example (cont.)

14
Time-Response of a Prototype
First-Order System

time constant

15
Time-Response of a Prototype
Second-Order System

G(s)

Characteristic equation:

R(s) = 1/s (unit-step input)

16
Unit-Step Responses

17
 Damping Ratio and Damping
Factor
• Characteristic equation:

• Unit-step response:

•  controls the rate of rise or decay of y(t).

18
 Natural Undamped Frequency
• Natural undamped frequency: n
• Damped (or conditional) frequency: 

  = cos −1 

19
20
Classification of System
Dynamics

21
Step-Response Comparison
overdamped

critically overdamped

underdamped

22
Step-Response Comparison
(cont.)
undamped

negative overdamped

negative overdamped

23
 Maximum Overshoot

y() is maximum when   1.

The first overshoot is n=1

dy (t )
=0
dt

25
Maximum Overshoot (cont.)

The first overshoot (n = 1) is the maximum overshoot

26
Maximum Overshoot (cont.)

27
 Delay Time
The time required for the step response to reach
50% of its final value  Set y(t) = 0.5 and solve
for t
• Approximation:

28
 Rise Time
The time for the step response to reach from 10
to 90% of its final value.
• Approximation:

29
 Settling Time: 0 <  < 0.69
The time required for the step response to
decrease and stay within a specified percentage
(2% or 5%) of its final value.

30
Settling Time:  > 0.69

31
Case study

32
 Speed and Position Control
of a DC Motor
• Open-loop response:

33
 Speed of Motor Shaft: Open-
Loop
• La is very small
 e = La/Ra (motor electric-time constant) is
neglected.

Keff = Km/(RaB+KmKb): motor gain constant

Superposition:
• TL(s)=0 (no disturbance and B=0) and Va(s)=A/s:

 (t) → A/Kb
• TL(s)=D/s and Va(s)=A/s :

 (t) → A/Kb− RaD/KmKb 35

36
 Speed of Motor Shaft: Closed-
Loop
• La = 0 

1/c
c: system mechanical-time constant
• in = A/s and TL = D/s:

steady-state response:
37
 Position Control: Open-Loop
• (s) = (s)/s

• Open-loop transfer function:

for small La 
38
Position Control: Closed-Loop

e = La/Ra → 0
for small La

39
Frequency-Domain Analysis of
Control Systems

40
 Frequency response
• The frequency response of a system is
defined as the steady-state response of
the system to a sinusoidal (harmonic)
input.

41
The Bode diagram of a typical
second order system

42
Gain and Phase Margins

43
 Position, velocity and acceleration error
constants in frequency domain

We usually use the notations cp, cv and ca for the cofficients, instead of Kp, Kv and Ka.

44