Scribd
Upload
48 views5 pages

Technology

Uploaded by

AliAlMaestro
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
48 views5 pages

Technology

Uploaded by

AliAlMaestro
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 5
FORMING TECHNIQUES FOR PLASTICS Quite a variety of different techniques are employed in the forming of polymeric ma- terials The method used for a specific polymer depends on several factors: (1) whether the material is thermoplastic or thermosetting; (2) if thermoplastic, the temperature at which it softens; (3) the atmospheric stability of the material being formed; and (4) the geometry and size of the finished product. There are numerous similarities between some of these techniques and those utilized for fabricating metals and ceramics. Fabrication of polymeric materials normally occurs at elevated temperatures and often by the application of pressure. Thermoplastics are formed above their glass transition temperatures, if amorphous, or above their melting temperatures, if semicrystalline. An applied pressure must be maintained as the piece is cooled so that the formed article will retain its shape. One significant economic benefit of us- ing thermoplastics is that they may be recycled; scrap thermoplastic pieces may be remelted and reformed into new shapes. Fabrication of thermosetting polymers is ordinarily accomplished in two stages. First comes the preparation of linear polymer (sometimes called a prepolymer) as a liquid, having a low molecular weight. This material is converted into the final hard and stiff product during the second stage, which is normally carried out in a mold haying the desired shape. This second stage. termed “curing,” may occur dur- ing heating and/or by the addition of catalysts, and often under pressure. During curing, chemical and structural changes occur on a molecular level: a crosslinked or a network structure forms, After curing, thermoset polymers may be removed from a mold while still hot, since they are now dimensionally stable. Thermosets are dif- ficult to recycle, do not melt, are usable at higher temperatures than thermoplas- tics, and are often more chemically inert. Molding is the most common method for forming plastic polymers. The sev- eral molding techniques used include compression, transfer, blow, injection, and extrusion molding. For each, a finely pelletized or granulized plastic is forced, at an elevated temperature and by pressure, to flow into, fill, and assume the shape of a mold cavit Compression and Transfer Molding For compression molding, the appropriate amounts of thoroughly mixed polymer and necessary additives are placed between male and female mold members, as illustrated in Figure 15.23. Both mold pieces are heated; however, only one is mov- able. The mold is closed, and heat and pressure are applied, causing the plastic to become viscous and flow to conform to the mold shape. Before molding, raw ma- terials may be mixed and cold pressed into a disc, which is called a preform. Pre- heating of the preform reduces molding time and pressure, extends the die lifetime, and produces a more uniform finished piece. This molding technique lends itself to the fabrication of both thermoplastic and thermosetting polymers; however, its use with thermoplastics is more time-consuming and expensive than the more com- monly used extrusion or injection molding techniques discussed below. In transfer molding. a variation of compression molding, the solid ingredients are first melted in a heated transfer chamber. As the molten material is injected into the 1 mo. 15.23 Schematic diagram of a T—— Platen compression molding tieat’and ] apparatus. (From F. W. cooling — _— |-4—— Wold plunger Bitlmeyer, Jr., Textbook UF Te Hai oin of Polymer Science, 3rd t+ Melding compound edition. Copyright © Hoat end eg old cavity 1984 by John Wiley & cooling [| |U q| Sons, New York. Mold TTT — if Paton Reprinted by permission base of John Wiley & Sons, Lee __ Hydraulic Inc.) plunger mold chamber, the pressure is distributed more uniformly over all surfaces. This process is used with thermosetting polymers and for pieces having complex geometries. Injection Molding Injection molding, the polymer analogue of die casting for metals, is the most widely used technique for fabricating thermoplastic materials. A schematic cross section of the apparatus used is illustrated in Figure 15.24. The correct amount of pelletized material is fed from a feed hopper into a cylinder by the motion of a plunger or ram. ‘This charge is pushed forward into a heating chamber where it is forced around a spreader so as to make better contact with the heated wall. As a result, the ther- moplastic material melts to form a viscous liquid. Next, the molten plastic is impelled, again by ram motion, through a nozzle into the enclosed mold cavity; pressure is maintained until the molding has solidified. Finally, the mold is opened, the piece is ejected, the mold is closed, and the entire cycle is repeated. Probably the most out- standing feature of this technique is the speed with which pieces may be produced. For thermoplastics, solidification of the injected charge is almost immediate: conse- quently, cycle times for this process are short (commonly within the range of 10 to 30s). Thermosetting polymers may also be injection molded; curing takes place while the material is under pressure in a heated mold, which results in longer cycle times than for thermoplastics. This process is sometimes termed reaction injection mold- ing (RIM) and is commonly used for materials such as polyurethane. Extrusion ‘The extrusion process is the molding of a viscous thermoplastic under pressure through an open-ended die, similar to the extrusion of metals (Figure 11.8c). A me- chanical screw or auger propels through a chamber the pelletized material, which Figure 15.24 Schematic diagram of an injection molding apparatus. (Adapted from EW. Billmeyer, Jr. Texthook of Polymer Science, 2nd edition. Copyright © 1971 by Mold John Wiley & Sons, New York. Reprinted by cavity. permission of John Wiley & Sons, Ine.) Fead hopper —D = Plastic polis: “Tubing and pipes —

You might also like