Soil Report KSM 4463 11-09-22

SOIL & FOUNDATION CO. LTD.
97 Prince Sultan Rd. Doha Dt.

Al Khobar. KSA
Tel # +966 138917469 / 8916127
Fax # +966 13 8917659
E-mail: [email protected]
www.applus.com
GEOTECHNICAL INVESTIGATION FOR THE PROPOSED

RAS AL KHAIR GRAIN TERMINAL PROJECT
RAS AL KHAIR, EASTERN AREA,
THE KINGDOM OF SAUDI ARABIA
FOR
UNITED FEED CO. LTD.

[email protected]
Kingdom of Saudi Arabia
97 Prince Sultan Rd. Doha Dt.
Al Khobar. KSA
Tel # +966 138917469 / 8916127
Fax # +966 13 8917659
E-mail: [email protected]
www.applus.com
August 30, 2022 Ref: KSM-4463
UNITED FEED CO. LTD.

[email protected]
Kingdom of Saudi Arabia
Sub.: Geotechnical Investigation Report for the Proposed Ras Al Khair Grain Terminal
Project located at Ras Al Khair, Eastern Area, Kingdom of Saudi Arabia.
We are pleased to submit the result of the geotechnical investigation, which we have performed for
the site of the abovementioned project.
The accompanying report presents our conclusions and recommendations along with the field and
laboratory tests upon which the recommendations are based.
We appreciate this opportunity to be of service to you on this project. Please do not hesitate to
contact us if you have any questions regarding this project, or if we can be of any further service.
Thank you and best regards,
SOIL & FOUNDATION CO., LTD.
Engr. Hesham Azam

Projects Manager
TABLE OF CONTENTS
Page
1.0 SCOPE 1
2.0 SITE DESCRIPTION 2
3.0 PROJECT DESCRIPTION 2
4.0 REGIONAL GEOLOGY 2
5.0 FIELD INVESTIGATION 3
6.0 LABORATORY OBSERVATIONS 4
7.0 GEOTECHNICAL CONDITION 5
7.1 Subsurface Formation 5

7.2 Groundwater Table 6
7.3 Project Site Seismicity 6
7.4 Geotechnical Parameters 6
8.0 GEOTECHNICAL RECOMMENDATIONS 8
8.1 Foundation Details 8

8.2 Depth of Foundations 14
8.3 Allowable Bearing Capacity 14
8.4 Modulus of Subgrade Reaction 14
8.5 Settlement 14
8.6 Lateral Earth Pressure Parameters 15
8.7 Site Grading and Soil Stability 15
8.8 Engineered Fill 16
8.9 Type of Cement 16
9.0 LIMITATIONS 17
LIST OF APPENDICES
APPENDIX I FIELD INVESTIGATIONS
Table 1 Summary of S.P.T. N Values, R.Q.D. Values and Sub-surface Formations
Figure No. 1 Site Plan and Location of Boreholes
Figure No. 2-17 Logs of Test Boring No. BH-1 to BH-16
APPENDIX II LABORATORY TEST RESULTS AND CURVES
APPENDIX III GUIDE SPECIFICATIONS FOR ENGINEERED FILL
APPENDIX IV SEISMIC MAP & GEOLOGICAL MAP
APPENDIX V PHOTOGRAPHS
GEOTECHNICAL INVESTIGATION FOR THE PROPOSED
RAS AL KHAIR GRAIN TERMINAL PROJECT
(RAS AL KHAIR, EASTERN PROVINCE)
THE KINGDOM OF SAUDI ARABIA
1.0 SCOPE
This report presents our investigation of the subsurface conditions at the site
for the Proposed Ras Al Khair Grain Terminal Project located at Ras Al Khair,
Eastern Province, the Kingdom of Saudi Arabia.
The purpose of this geotechnical investigation is to determine the depth and
characteristics of the different subsurface formations and recommended
allowable bearing capacity and expected settlements under the proposed
structure.
This report includes guidelines for earthwork construction specification, site
and structure descriptions, field investigation, laboratory observations,
subsurface formations and geotechnical recommendation.
Page 1
2.0 SITE DESCRIPTION
The site of the Proposed Ras Al Khair Grain Terminal project is located in site
at Ras Al Khair, Eastern Province, Kingdom of Saudi Arabia. Figure 1 in
Appendix I presents the site plan with boreholes locations.
3.0 PROJECT DESCRIPTION
It is understood from the information provided by the client that the proposed
project consists of Storage Silos, Flat Store Warehouse, Bagging Station,
Flakes/Transfer Tower, Ship Unloading Conveyor & Unloader and Weight
Bridge Scale House
4.0 REGIONAL GEOLOGY
As per the Geologic Map (GM-208-A) the site is under Sand (Qtc) and Silt
(Qs) and associated fine sediments including caliche-like and gypsiferous
deposits in undrained depression; gravel composed chiefly of limestone and
other rocks of local origin, includes older gravels in some areas.
Page 2
5.0 FIELD INVESTIGATION
After the visual inspection of the site, the subsurface soil investigation was
performed on August 13-24, 2022. Sixteen (16) exploratory borings were
drilled at the location shown on the enclosed site plan (Figure 1, Appendix I).
The boring was drilled by the use of trucks mounted Mobile B-53 drilling rigs
utilizing tricone bit & casing. Borehole number, location and depth was made
according to the project requirements to cover the site and satisfy the
geotechnical needs of the project as can be seen in Figure 1 Appendix I. Both
sampling and field testing were conducted in accordance with the applicable
ASTM specifications.
The log of the borehole is shown in Appendix I, wherein a continuous profile of
each borehole was prepared by an experienced engineering geologist to
present clearly all the subsurface soils encountered.
Soil samples were collected at frequent intervals using a standard 50 mm
(outside diameter) split-spoon sampler driven with a 63.5 kg automatic
hammer with a drop height of 0.76 m in accordance with the Standard
Penetration Test (SPT) procedures (ASTM D 1586-11).
The following table presents the correlation between field tests (SPT) and soil
properties (After Peck et al., 1974).
Page 3
The following table presents the correlation between field tests (SPT) and soil
properties (After Peck et al., 1974).
Table 1 SPT Correlation
Granular Soil Cohesive Soil

Relative
SPT N * SPT N * Consistency
Density
0-4 Very loose <2 Very soft
5-10 Loose 2-4 Soft
Medium
11-30 5-8 Medium
Dense
31-50 Dense 9-15 Stiff
>50 Very dense 16-30 Very stiff
- - >30 Hard
6.0 LABORATORY OBSERVATIONS
All soil samples were placed in moisture-proof sealed bags and transported to
our laboratory in Dhahran for visual inspection and laboratory classification
testing in general accordance with ASTM standards. The selected soil/rock
samples were tested for the following parameters:
 Grain size Analysis (ASTM D-421, 422)
 Determination of Water content (ASTM D-2216)
 Atterberg Limits, (ASTM-4318)
Page 4
 Chemical tests, Sulphate Content, Chloride Content & pH
(BS 1377 Past 3)

The results of the lab testing performed are provided in Appendix II.
7.0 GEOTECHNICAL CONDITION
7.1 Subsurface Formation
The subsurface soil field information that have been provided from the sixteen
(16) boring, drilled to the depth of 15.0m, 25.0m. 30.0m and 40.0m below the
boreholes present levels revealed that the subsurface formation mainly consists
of two (02) subsoil formation that are extending from the existing borehole surface
to the total depth investigated. The estimated soil profile is composed of the
following:
1. Sand Layer: From the top, a layer of light brown, very loose to dense, Poorly
Graded Sand extending to 28.50m as shown in the borehole logs. In some
boreholes a mix of sand, gravel, cobbles was encountered at depth between
4.50m to 10.50m as shown in the borehole logs.
2. Elastic Silt: Below the top layers, a layer of a layer of light greenish/creamy,
hard, Elastic Silt was encountered down to the maximum depth of 40.0m.
Page 5
7.2 Groundwater Table
Groundwater table was encountered at the depth of -3.20m to -4.25m from the
borehole surface level at this site at the time of drilling until maximum depths
investigated. It must be noted that fluctuation of ground water level (+0.80m to
1.00m) may be occurred due to irrigation, drainage, rainfall, high and low tide
and other factors. Hence, specifications and construction planning should
recognize the possibilities of variation.
7.3 Project Site Seismicity
According to the Saudi Building Code 2018 (SBC 301-CR-18) figure 22-1 &
22-2, and based on the geotechnical properties of the encountered soils, the
Project Site Seismicity parameters are presented in the following table:
Table 2: Site Seismicity
Parameter Value
Ss.g% 10.0
S1.g% 6.0
Site Class
For Seismic Design D (after soil improvement)
(table 14.1.1)
7.4 Geotechnical Design Parameters – The following soil parameters have
been adopted on the basis of geotechnical data of the site.
Page 6
Table 3: Soil/Rock Parameters
Angle of
Depth below the Bulk
Cohesion Internal
Soil Type existing ground Density Ka Kp Ko
(c)kPa Friction
level (m) (Kn/m³)
(Φ) deg
SP
Mix Sand, 0.0 to 9.00
18 -- 30 0.333 3.000 0.500
gravel, (not consider in
cobbles the analysis)
Sand
9.00 to 28.50 18 -- 32 0.307 3.255 0.470
(SP)
Elastic Silt
28.50 to 40.00 19 100 - - - -
(MH)
The following geotechnical design parameters have been considered for
select fill material:
γ = 19 kN/m³, c = 0, Φ = 32°
Ka=0.307 Kp=3.255 Ko=0.47
7.4.1 Modulus of Elasticity - The range value of Modulus of Elasticity (Es) for
the different type of soil was presented below as per Ref. Principles of
Foundation Engineering, B.M. Das 6th Edition.
Table 4: Elastic Parameters of Various Soils/Rock
Modulus of Poisson’s
Soil Type
Elasticity (MN/m²) ratio
Loose sand 10.50 – 24.0 0.20 – 0.40
Medium dense sand 17.25 – 27.60 0.25 – 0.40
Dense sand 34.50 – 55.20 0.30 – 0.45
Silty sand 10.35 – 17.25 0.20 – 0.40
Sand and gravel 69.00 – 172.50 0.15 – 0.35
Soft clay 4.1 – 20.7 --
Medium clay 20.7 – 41.4 0.20 – 0.50
Stiff clay 41.4 – 96.6 --
Sandstone 3.0 – 42 (x10³) 0.2 – 0.45
Page 7
The method of estimation of elastic modulus as presented by Bowles, 1996 and AASHTO LRFD are
adopted as well, in this report. Please refer to the appendix
8.0 GEOTECHNICAL RECOMMENDATIONS
8.1 Foundation Detail - Based on the in-situ conditions of the soils
encountered and the type of the proposed structure, find below the
geotechnical recommendation:
Table 6: Foundation Details

Modulus
Net
of
Foundation Allowable
Type of Excavation Replacement Subgrade
Structure Depth Bearing Depth (m) Level (m)
Foundation Reaction
(m) Capacity
(Ks)
(kPa)
(kN/m³)
Storage
Silos, Flat
Deep
Store Pile recommendations refer to sec. 8.1.a
Foundation
Warehouse,
Bagging
Station,
Flakes/Transf
er Tower,
Ship Shallow
Unloading Foundation
Soil Improvement by Stone Column refer to sec. 8.1.b
Conveyor & with soil
Unloader and improvement
Weight
Bridge Scale
House
Page 8
8.1.a Deep Foundation (Pile cast in situ)
The recommended foundations (bottom of pile caps) should be placed at
a depth of -0.60m (minimum) below the existing ground level.
The recommended allowable loads for piles are the following:
Table 6a: Pile Recommendation
Maximum Maximum
Vl. Modulus of Estimated
Allowable Allowable
Pile Pile Sub- Grade Factory of Pile
Capacity in Capacity in
Diameter Length Reaction Safety Settlement
Compression Tension
3
(mm) (m) KN/m mm
(kN) (kN)
25 1500 780 119,284 <25.0
800 30 2100 1150 166,998 <25.0
35 2900 1800 230,616 <25.0

FOS
25 2200 1100 112,102 Side = <25.0
1.50
1000 30 3000 1600 152,866 <25.0
&
35 4000 2400 203,822 FOS Tip <25.0
= 3.00
25 2800 1400 99,027 <25.0
1200 30 3800 2100 134,394 <25.0
35 5000 3100 176,835 <25.0
Notes: (1) The above piles capacities should be checked in site by

contractor by adopting pile load testing.
(2) The above piles capacities should be reduced by group action effect
using the attached chart from NAVFAC.
Page 9
Table 7: Lateral Coefficient of Subgrade Reaction
Kh (kN/m3)= fz/D
Layer Layer 3
z f (kN/m ) D (mm) D (mm) D (mm)
thickness Classification
800 1000 1200
Mix Sand, gravel
9.0
cobbles
4.50 3000 16,875 13,500 11,250
SP
19.5
(m. dense to dense)
18.75 8500 199,218 159,375 132,812
MH
11.50
(hard)
34.25 3300 141,281 113,025 75,350
General Important Notes for piles foundations:
1. The final depths of piles will be ascertained based on piles loading tests
which should be carried out before proceeding with the work. The data
mentioned on the above table will be revised accordingly.
Page 10
2. The pile should be reinforced with its full length.
3. The depth of pile on which the pile capacity has been calculated is
starting from the bottom level of the pile cap (-0.60m).
4. The compressive strength of the concrete used for casting piles and pile
caps should not be less than 300Kg/cm2. The cement content of the
concrete should not be less than 400Kg/m3.
5. Water cement ratio for the concrete used for piles and piles caps should
not be more than 0.40. The concrete cover for the reinforcement should
not be less than 75mm.
6. The minimum spacing (centre to centre) between piles should be 2.5 to
3.0 times their diameters.
7. Adequate number of pile load tests should be carried at any location of
single pile to confirm the allowable pile capacity; the test should follow
ASTM specifications D-1143.
8. Cement Type-V should be used for all concrete works such as piles and
pile caps.
9. 50cm of rock fill 1.5” – 3.5” (No. “1” of AASHTO M43) should be applied
and perfectly compacted under piles caps.
Page 11
8.1.b Soil Improvement by Stone Column (Vibro Replacement)
Page 12
Based on our field explorations, soil layer with debris material were
encountered as shown in the boring logs and are presented in Appendix I.
The soil layers with debris material were encountered from surface to
depths varying from 0.00m to 9.00m. Bearing capacity for the proposed
structures can be improved by replacing loose material with stone
columns. Stone columns can be installed to a depth of 12.0m to 15.0m
below existing ground level. This method consists of lowering vibratory
probe into the ground and replacing the loose material with aggregate to
achieve adequate compaction. The spacing of probe points and exact
depth of treatment is depending on the equipment used by Specialist
Contractor. After the improvement, required bearing capacity could be
attained for isolated spread/strip footing and rigid raft foundations
depending upon the spacing and the depth of the stone columns.
Specialist contractor should be consulted for detailed information for the
achievable Safe Bearing Capacity using the employed equipment. At the
investigated locations by installing stone columns, safe bearing capacity
of the existing soil can be improved up to 150-200 KPa. For plan layout
and sectional details with design calculations and sequence of
construction for stone columns, specialist contractors could be consulted.
Note: For safety of the existing structures, outer boundary of the soil
improvement area should be at least 5.0m away from the existing
structure. The replacement material shall consist of hard, durable
Page 13
fragment of stone or gravel. As a general rule, suitable size of material is
1-4 inches.
Quality Assurance for Vibro-Replacement
- The Contractor shall prove by tests that the improved ground will safely
carry the design load.
- The test program and vibro pattern shall be proposed by the contractor
and to be approved by Owner's Representative.
- Quality Control tests, such as Dutch Cone Test or boreholes with
continuous SPT shall be performed by Independent Laboratory.
Contractor's proposal shall contain field trials and Plate / Zone Load Tests
after soil improvement. Load test shall be performed for Quality Control.
Such that, after soil improvement, at least Four (04) Plate Load Tests
(PLT) following ASTM D-1196 and One (01) Zone Load Test (ZLT) using
plate size of minimum 1.5m x 1.5m shall be performed per each tank and
one for every 2000 square meters of the improved area or minimum two
tests per site is recommended. The test shall be performed on a precast
footing at least up to 1.5 times the design load.
8.2 Depth of Foundation -The recommended depth of foundation is below the
existing borehole level.
Page 14
8.3 Allowable Bearing Capacity - The recommended bearing value is the net
allowable pressure, which should be used in the design for total dead and
live loads.
8.4 Modulus of Subgrade Reaction - The recommended values Modulus of
Subgrade Reaction (Ks) is correlated to the recommended net bearing
capacity values using the equation
proposed by (Bowles, 1996):
Ks = FS qa / ΔH (kN/m³)
qa = The Net Allowable Bearing Pressure.
∆H = Settlement, FS= Factory of Safety
8.5 Settlement - By applying the above-mentioned soil pressure, the
estimated total settlement under the recommended foundations should be
less than 2.50cm for isolated footing and 5.00 cm for raft foundation. The
differential settlement will be within tolerable limits.
8.6 Lateral Earth Pressure Parameters
Page 15
For granular soil Backfill behind basement/retaining walls, the following soil
parameters could be used for the design:
Table 6: Lateral Earth Pressure Parameters

Effective friction angle (Ф’) 30°
Total unit weight (γ) 18 kN/m3
Effective unit weight (γ’) 8 kN/m3
At rest lateral earth pressure (Ko) 0.5
Active lateral earth pressure (Ka) 0.33
Passive lateral earth pressure (Kp) 3
Coefficient of friction between soil & concrete 0.45
8.7 Site grading and Slope stability
All areas to receive new structures should be stripped, cleared from all
vegetation, topsoil, debris and rubbish fill material. Temporary excavation
could be performed at 2.0H: 1V inclination (Horizontal: Vertical) or
otherwise shoring system is recommended.
Ordinary equipment can be used for the excavation of the soil while jack
hammer will be used for rock excavation.
8.8 Engineered Fill
The fill to be used to raise the grade around and above footings shall
Page 16
consist of suitable engineered fill such as A-1-a, A-1-b, A-2-4 & A-3
material (confined area) as per AASHTO -145 classifications, and should
be spread in uniform lifts not exceeding 25cm in thickness and compacted
to a minimum standard compaction of 95%.
The structural (engineered) fill used to raise ground level under footing
shall consist of well graded granular soil such as A-1-a or A-1-b as per
AASHTO classification and should be placed in layer not exceeding 25cm
in thickness and compacted to the required 95% compaction of the
maximum dry density according to ASTM D-1557 specification. The
exposed surface of excavation to receive Engineered Fill should be proof-
rolled using heavy compactor. Appendix III presents the Engineered Fill
requirements.
8.9 Type of Cement
According to the chemical analysis which has been conducted on the
subsurface soil it is recommended to use Type I cement with MS in the
foundation and subsurface construction. Cement content should not be
less than 400kg/m3, while the minimum concrete cover for the
reinforcement should not be less than 75mm. with a water/cement ratio not
Page 17
exceeding 0.40. In addition, waterproofing membrane is recommended to
use in the subsurface concrete.
9.0 LIMITATIONS
The recommendations which are given in this report are based on the
assumption that the soil condition does not deviate appreciably from those
disclosed in the borings and laboratory test results. At the time of
construction, if there will be any unanticipated variations in the subsurface
conditions or if the proposed construction will differ from those planned at
this time, as it is described in this report, the SAFCO should be notified to
verify the bottom of excavation so that supplementary recommendations
can be given.
Please note that all the samples recovered from this investigation will be
discarded after 15 days upon the submission of this final report if the client
does not ask formally for the retention of the samples.
Our company, after having been chosen to perform this geotechnical
investigation, shall in case of counter claims be liable only to the extent of
what has been paid for the work done.
Page 18
APPENDIX I
FIELD INVESTIGATIONS
Soil & Foundation Co. Ltd., C.R. 2051033757 - C.C. No. 78673
TABLE 1 : SUMMARY OF S.P.T. N-VALUES, RQD VALUES
AND SUBSURFACE FORMATIONS
Project : Proposed Ras Al Khair Grain Terminal Project Date : 25/8/2022
Location : Ras Al Khair, K.S.A. Ref. No.: KSM-4463

DEPTH S.P.T. N- VALUES SPT N - VALUES RQD - VALUES
(M) BH-1 BH-2 BH-3 BH-4 BH-5 BH-6 BH-7 BH-8 BH-9 BH-10 BH-11 BH-12 BH-13 BH-14 BH-15 BH-16 MAX. MIN. AVG. MAX. MIN. AVG.
0.00 4 5 6 5 4 5 6 3 3 4 4 7 5 5 3 6 7 3 5
1.50 6 6 5 5 7 7 4 7 5 8 8 14 14 9 5 7 14 4 7
3.00 8 7 7 7 9 8 7 8 7 9 10 17 17 10 6 7 17 6 9
4.50 - 7 6 8 10 11 7 10 8 9 10 - 23 10 7 9 23 6 10
6.00 - 8 9 11 13 11 9 11 11 13 11 - 27 13 8 12 27 8 12
7.50 - 11 9 13 14 14 11 12 13 14 13 - - 13 11 14 14 9 12
9.00 - 16 15 15 15 14 14 17 16 12 15 - 12 16 15 16 17 12 15
10.50 16 18 17 19 17 18 17 18 23 17 18 14 15 18 18 20 23 14 18
12.00 20 22 20 22 22 20 20 22 24 19 21 14 18 20 21 24 24 14 21
13.50 21 24 22 27 26 21 22 27 25 24 23 18 20 23 23 29 29 18 23
15.00 24 25 24 30 27 23 24 26 28 26 28 41 23 28 28 41 23 27
16.50 28 31 27 33 26 24 29 28 28 26 31 40 31 32 26 40 24 29
18.00 29 34 31 33 33 31 31 33 30 37 33 38 35 33 37 38 29 33
19.50 35 37 35 37 23 34 32 33 32 40 36 39 39 35 38 40 23 35
21.00 37 39 38 39 37 34 37 37 34 41 39 42 44 39 41 44 34 39
22.50 40 51 37 41 37 40 40 40 38 42 42 42 49 41 42 51 37 41
24.00 41 50 44 44 36 39 42 44 40 43 44 43 42 44 44 50 36 43
25.50 46 54 46 48 41 49 44 46 48 49 54 41 47
27.00 50 30 52 53 53 55 50 49 48 55 55 30 50
28.50 100 100 100 100 100 100 100 100 100 100 100 100 100
30.00 100 100 100 100 100 100 100 100 100 100
31.50 100 100 100 100 100 100 100 100 100 100
33.00 100 100 100 100 100 100 100 100 100 100
34.50 100 100 100 100 100 100 100 100 100 100
36.00 100 100 100 100 100 100 100 100 100 100
37.50 100 100 100 100 100 100 100 100 100 100
39.00 100 100 100 100 100 100 100 100 100 100
40.00
This document should be read with:
1. TS2260-GDE-100-00 - Ras Alkheir Grain Terminal Project_Geotechnical Investigation Program
2. Attachment # 002- Ras Alkhair Grain Terminal Project_BH Schedule

TEST BORING LOG
BORING NO.: BH-1
PROJECT : PROPOSED GRAIN TERMINAL PROJECT DATE STARTED : 18-08-2022

CLIENT : UNITED FEED CO. LTD. DATE FINISHED : 18-08-2022
LOCATION : RAS AL KHAIR, K.S.A. DRILL RIG : MOBILE B-53
PROJECT NO. : KSM-4463 ELEVATION : DRILLER : ALAM
GWD : 3.90M NORTH : 3050133.74 GEOLOGIST : SHAZAD
GWL : EAST : 320960.333 TOTAL DEPTH : 40.0M
SOIL SYMBOLS, CURVE
ELEV/ SPT W.C. L L P I REC. SAMPLE (S.P.T.)
DEPTH
SAMPLERS USCS Description (N) (%) (%) (%) (%) NO.
AND TEST DATA
20 40 60 80
0
1 / 15 SP POORLY GRADED SAND with sea 4 BH-1-1
2 / 15
2 / 15 shells,
light brown, very loose, dry.
SP
POORLY GRADED SAND,
3 / 15 6 2.1 - NP BH-1-2
3 / 15 light brown, dry.
2 13 / 15
3 / 15 ditto. 8 BH-1-3
4 / 15
4 / 15
4
MIX OF SAND, SILT, GRAVEL & BH-1-4

COBBLES.
6
ditto. BH-1-5
ditto. BH-1-6
8
ditto. BH-1-7
10
6 / 15 SP 16 BH-1-8
8 / 15 POORLY GRADED SAND,
10 / 15 light brown, medium dense, wet.
12 9 / 15 20
ditto. BH-1-9
9 / 15
11 / 15
8 / 15 ditto. 21 13.0 - NP BH-1-10

9 / 15
14 12 / 15
9 / 15 ditto. 24 BH-1-11
11 / 15
14 / 15
16
10 / 15 ditto. 28 BH-1-12
13 / 15
15 / 15
18 11 / 15 29
ditto. BH-1-13
13 / 15
Drilling performed by 6" hollow stem auger.

Coring in rock performed using double tube core.
Figure PAGE 1 of 3 Soil and Foundation Co., Ltd.
TEST BORING LOG
BORING NO.: BH-1

PROJECT NO. : KSM-4463 ELEVATION : DRILLIER : ALAM
SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
16 / 15
13 / 15 ditto. 35 BH-1-14
16 / 15
20 19 / 15
14 / 15 ditto. 37 BH-1-15
17 / 15
20 / 15
22
15 / 15 ditto. 40 BH-1-16
18 / 15
22 / 15
24 15 / 15 41
ditto. BH-1-17
18 / 15
23 / 15
16 / 15 ditto. 46 BH-1-18
21 / 15
26 25 / 15
16 / 15 ditto. 50 BH-1-19
22 / 15
28 / 15
28
50 / 10 MH 100 BH-1-20
ELASTIC SILT,
light greenish, hard.
30 50 / 9 100 29.9 144 58

ditto. BH-1-21
50 / 7 ditto. 100 BH-1-22

32
50 / 9 ditto. 100 BH-1-23
34
50 / 7 ditto. 100 BH-1-24
36 50 / 8 100
ditto. BH-1-25

TEST BORING LOG
BORING NO.: BH-1

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
50 / 7 ditto. 100 BH-1-26

38
50 / 6 ditto. 100 BH-1-27
40
END OF BORING.
42
44
46
48
50
52
54

TEST BORING LOG
BORING NO.: BH-2

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
2 / 15
3 / 15 shells,
light brown, loose, dry.
SP
POORLY GRADED SAND,
3 / 15 6 BH-2-2
2 3 / 15 loose.
3 / 15 ditto. 7 BH-2-3
3 / 15
4 / 15
4
3 / 15 ditto. 7 12.4 - NP BH-2-4

4 / 15
3 / 15
6 4 / 15 8
ditto. BH-2-5
4 / 15
4 / 15
4 / 15 medium dense. 11 BH-2-6

5 / 15
8 6 / 15
6 / 15 ditto. 16 BH-2-7
7 / 15
9 / 15
10
7 / 15 ditto. 18 BH-2-8
8 / 15
10 / 15
12 7 / 15 22
ditto. BH-2-9
10 / 15
12 / 15
7 / 15 ditto. 24 BH-2-10
11 / 15
14 13 / 15
8 / 15 ditto. 25 BH-2-11
11 / 15
14 / 15
16
11 / 15 dense. 31 BH-2-12
14 / 15
17 / 15
18 11 / 15 34
ditto. BH-2-13
16 / 15

TEST BORING LOG
BORING NO.: BH-2

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
18 / 15
13 / 15 ditto. 37 BH-2-14
17 / 15
20 20 / 15
15 / 15 ditto. 39 BH-2-15
18 / 15
21 / 15
22
16 / 15 very dense. 51 BH-2-16

18 / 15
23 / 15
24 17 / 15 50
ditto. BH-2-17
22 / 15
28 / 15
18 / 15 ditto. 54 BH-2-18
25 / 15
26 29 / 15
10 / 15 dense. 30 BH-2-19
14 / 15
16 / 15
28
50 / 9 MH 100 BH-2-20
ELASTIC SILT,
light creamy to light greenish, hard.
30 50 / 8 100 31.2 144 58

ditto. BH-2-21
50 / 7 ditto. 100 BH-2-22

32
50 / 7 ditto. 100 BH-2-23
34
50 / 6 ditto. 100 BH-2-24
36 50 / 7 100
ditto. BH-2-25

TEST BORING LOG
BORING NO.: BH-2

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
50 / 8 ditto. 100 BH-2-26

38
50 / 9 ditto. 100 BH-2-27
40
END OF BORING.
42
44
46
48
50
52
54

TEST BORING LOG
BORING NO.: BH-3

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
3 / 15
3 / 15 shells,
SP
POORLY GRADED SAND,
3 / 15 5 3.1 - NP BH-3-2
2 2 / 15 loose.
2 / 15 ditto. 7 BH-3-3
3 / 15
2 / 15
4
3 / 15 ditto. 6 BH-3-4
3 / 15
3 / 15
6 3 / 15 9
ditto. BH-3-5
4 / 15
5 / 15
4 / 15 ditto. 9 BH-3-6
5 / 15
8 4 / 15

7 / 15
8 / 15
10
6 / 15 ditto. 17 BH-3-8
8 / 15
9 / 15
12 7 / 15 20
ditto. BH-3-9
9 / 15
11 / 15
8 / 15 ditto. 22 BH-3-10
10 / 15
14 12 / 15
8 / 15 ditto. 24 BH-3-11
11 / 15
13 / 15
16
10 / 15 ditto. 27 BH-3-12
12 / 15
15 / 15
18 11 / 15 31
dense. BH-3-13
14 / 15

TEST BORING LOG
BORING NO.: BH-3

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
17 / 15
12 / 15 ditto. 35 BH-3-14
16 / 15
20 19 / 15
14 / 15 ditto. 38 BH-3-15
17 / 15
21 / 15
22
14 / 15 ditto. 37 BH-3-16
17 / 15
20 / 15
24 16 / 15 44
ditto. BH-3-17
20 / 15
24 / 15
16 / 15 ditto. 46 BH-3-18
21 / 15
26 25 / 15
18 / 15 very dense. 52 BH-3-19

24 / 15
28 / 15
28
50 / 9 MH 100 BH-3-20
ELASTIC SILT,
light creamy to light greenish, hard.
30 50 / 10 100
ditto. BH-3-21
50 / 7 ditto. 100 BH-3-22

32
50 / 6 ditto. 100 BH-3-23
34
50 / 8 ditto. 100 BH-3-24
36 50 / 7 100 28.5 130 57

ditto. BH-3-25

TEST BORING LOG
BORING NO.: BH-3

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
50 / 8 ditto. 100 BH-3-26

38
50 / 8 ditto. 100 BH-3-27
40
END OF BORING.
42
44
46
48
50
52
54

TEST BORING LOG
BORING NO.: BH-4

PROJECT NO. : KSM-4463 ELEVATION : DRILLER : SHAHID
SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
2 / 15
3 / 15 shells,
SP
POORLY GRADED SAND,
2 / 15 5 BH-4-2
2 3 / 15 loose.
2 / 15 ditto. 7 4.9 - NP BH-4-3

3 / 15
4 / 15
4
3 / 15 ditto. 8 BH-4-4
3 / 15
5 / 15
6 4 / 15 11
medium dense. BH-4-5
5 / 15
6 / 15
5 / 15 ditto. 13 BH-4-6
6 / 15
8 7 / 15
6 / 15 ditto. 15 BH-4-7
7 / 15
8 / 15
10
8 / 15 ditto. 19 BH-4-8
9 / 15
10 / 15
12 9 / 15 22
ditto. BH-4-9
10 / 15
12 / 15
10 / 15 ditto. 27 BH-4-10
13 / 15
14 14 / 15
11 / 15 dense. 30 BH-4-11
14 / 15
16 / 15
16
12 / 15 ditto. 33 BH-4-12
15 / 15
18 / 15
18 13 / 15 33
ditto. BH-4-13
14 / 15

TEST BORING LOG
BORING NO.: BH-4

PROJECT NO. : KSM-4463 ELEVATION : DRILLIER : SHAHID
SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
19 / 15
14 / 15 ditto. 37 BH-4-14
17 / 15
20 20 / 15
15 / 15 ditto. 39 BH-4-15
18 / 15
21 / 15
22
16 / 15 ditto. 41 BH-4-16
18 / 15
23 / 15
24 17 / 15 44
ditto. BH-4-17
20 / 15
24 / 15
17 / 15 ditto. 48 BH-4-18
22 / 15
26 26 / 15
18 / 15 very dense. 53 BH-4-19

24 / 15
29 / 15
28
50 / 10 MH 100 BH-4-20
ELASTIC SILT,
light creamy, hard.
30 50 / 9 100 32.1 144 58

ditto. BH-4-21
50 / 8 ditto. 100 BH-4-22

32
50 / 7 ditto. 100 BH-4-23
34
50 / 8 light greenish, hard. 100 BH-4-24
36 50 / 7 100
ditto. BH-4-25

TEST BORING LOG
BORING NO.: BH-4

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
50 / 9 ditto. 100 BH-4-26

38
50 / 8 ditto. 100 BH-4-27
40
END OF BORING.
42
44
46
48
50
52
54

TEST BORING LOG
BORING NO.: BH-5

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
2 / 15
2 / 15 shells,
SP
POORLY GRADED SAND,
3 / 15 7 1.8 - NP BH-5-2
2 4 / 15 loose.
3 / 15 ditto. 9 BH-5-3
4 / 15
5 / 15
4
4 / 15 ditto. 10 BH-5-4
5 / 15
5 / 15
6 5 / 15 13
6 / 15
7 / 15
5 / 15 ditto. 14 BH-5-6
7 / 15
8 7 / 15
6 / 15 ditto. 15 13.0 - NP BH-5-7

7 / 15
8 / 15
10
7 / 15 ditto. 17 BH-5-8
8 / 15
9 / 15
12 8 / 15 22
ditto. BH-5-9
10 / 15
12 / 15
9 / 15 ditto. 26 BH-5-10
12 / 15
14 14 / 15
11 / 15 ditto. 27 BH-5-11
13 / 15
14 / 15
16
11 / 15 ditto. 26 BH-5-12
14 / 15
12 / 15
18 11 / 15 33
dense. BH-5-13
15 / 15

TEST BORING LOG
BORING NO.: BH-5

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
18 / 15

10 / 15
20 13 / 15
13 / 15 dense. 37 BH-5-15
17 / 15
20 / 15
22
13 / 15 ditto. 37 BH-5-16
16 / 15
21 / 15
24 13 / 15 36
ditto. BH-5-17
14 / 15
22 / 15
14 / 15 ditto. 41 BH-5-18
18 / 15
26 23 / 15
17 / 15 very dense. 53 BH-5-19

24 / 15
29 / 15
28
50 / 12 MH 100 BH-5-20
ELASTIC SILT,
light creamy, hard.
30 50 / 9 100
ditto. BH-5-21
50 / 10 ditto. 100 BH-5-22

32
50 / 7 ditto. 100 BH-5-23
34
36 50 / 7 100
ditto. BH-5-25

TEST BORING LOG
BORING NO.: BH-5

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
50 / 7 ditto. 100 BH-5-26

38
50 / 6 ditto. 100 BH-5-27
40
END OF BORING.
42
44
46
48
50
52
54

TEST BORING LOG
BORING NO.: BH-6

PROJECT NO. : KSM-4463 ELEVATION : DRILLER : SHAHED
SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
2 / 15
3 / 15 shells,
SP
POORLY GRADED SAND,
3 / 15 7 2.0 - NP BH-6-2
2 4 / 15 loose.
3 / 15 ditto. 8 BH-6-3
4 / 15
4 / 15
4
9 / 15 ditto. 11 BH-6-4
5 / 15
6 / 15
6 5 / 15 11
5 / 15
6 / 15
5 / 15 ditto. 14 BH-6-6
6 / 15
8 8 / 15
6 / 15 ditto. 14 BH-6-7
6 / 15
8 / 15
10
6 / 15 ditto. 18 BH-6-8
8 / 15
10 / 15
12 7 / 15 20
ditto. BH-6-9
9 / 15
11 / 15
9 / 15 ditto. 21 BH-6-10
9 / 15
14 12 / 15
9 / 15 ditto. 23 BH-6-11
10 / 15
13 / 15
16
10 / 15 ditto. 24 BH-6-12
13 / 15
11 / 15
18 10 / 15 31
dense. BH-6-13
14 / 15

TEST BORING LOG
BORING NO.: BH-6

PROJECT NO. : KSM-4463 ELEVATION : DRILLIER : SHAHED
SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
17 / 15

15 / 15
20 19 / 15
13 / 15 dense. 34 BH-6-15
16 / 15
18 / 15
22
15 / 15 ditto. 40 BH-6-16
18 / 15
22 / 15
24 15 / 15 39
ditto. BH-6-17
18 / 15
21 / 15
17 / 15 ditto. 49 BH-6-18
23 / 15
26 26 / 15
17 / 15 very dense. 55 BH-6-19

25 / 15
30 / 15
28
50 / 14 MH 100 BH-6-20
ELASTIC SILT,
light creamy, hard.
30 50 / 12 100
ditto. BH-6-21
50 / 11 ditto. 100 BH-6-22

32
50 / 9 ditto. 100 BH-6-23
34
50 / 8 light greenish, hard. 100 30.9 144 58 BH-6-24
36 50 / 7 100
ditto. BH-6-25

TEST BORING LOG
BORING NO.: BH-6

PROJECT NO. : KSM-4463 ELEVATION : DRILLIER : SHAHED
SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
50 / 6 ditto. 100 BH-6-26

38
50 / 5 ditto. 100 BH-6-27
40
END OF BORING.
42
44
46
48
50
52
54

TEST BORING LOG
BORING NO.: BH-7

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
3 / 15
3 / 15 shells,
SP
POORLY GRADED SAND,
2 / 15 4 1.9 - NP BH-7-2
2 2 / 15 very loose.
2 / 15 loose. 7 BH-7-3
3 / 15
4 / 15
4
3 / 15 ditto. 7 BH-7-4
3 / 15
4 / 15
6 3 / 15 9
ditto. BH-7-5
4 / 15
5 / 15

5 / 15
8 6 / 15
5 / 15 ditto. 14 BH-7-7
6 / 15
8 / 15
10
6 / 15 ditto. 17 BH-7-8
8 / 15
9 / 15
12 7 / 15 20
ditto. BH-7-9
9 / 15
11 / 15
8 / 15 ditto. 22 BH-7-10
10 / 15
14 12 / 15
9 / 15 ditto. 24 BH-7-11
11 / 15
13 / 15
16
11 / 15 ditto. 29 BH-7-12
14 / 15
15 / 15
18 11 / 15 31
dense. BH-7-13
14 / 15

TEST BORING LOG
BORING NO.: BH-7

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
17 / 15
13 / 15 ditto. 32 BH-7-14
14 / 15
20 18 / 15
14 / 15 ditto. 37 BH-7-15
17 / 15
20 / 15
22
14 / 15 ditto. 40 BH-7-16
18 / 15
22 / 15
24 15 / 15 42
ditto. BH-7-17
19 / 15
23 / 15
16 / 15 ditto. 44 BH-7-18
19 / 15
26 25 / 15
17 / 15 very dense. 50 BH-7-19

22 / 15
28 / 15
28
50 / 11 MH 100 BH-7-20
ELASTIC SILT,
light creamy, hard.
30 50 / 10 100
ditto. BH-7-21
50 / 8 ditto. 100 BH-7-22

32
50 / 7 ditto. 100 BH-7-23
34
36 50 / 6 100 32.1 144 58

ditto. BH-7-25

TEST BORING LOG
BORING NO.: BH-7

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
50 / 6 ditto. 100 BH-7-26

38
50 / 5 ditto. 100 BH-7-27
40
END OF BORING.
42
44
46
48
50
52
54

TEST BORING LOG
BORING NO.: BH-8

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
1 / 15
2 / 15 shells,
SP
POORLY GRADED SAND,
2 / 15 7 BH-8-2
2 4 / 15 loose.
3 / 15 ditto. 8 BH-8-3
3 / 15
5 / 15
4
3 / 15 ditto. 10 12.7 - NP BH-8-4

5 / 15
5 / 15
6 4 / 15 11
5 / 15
6 / 15
5 / 15 ditto. 12 BH-8-6
5 / 15
8 7 / 15
6 / 15 ditto. 17 BH-8-7
8 / 15
9 / 15
10
6 / 15 ditto. 18 BH-8-8
8 / 15
10 / 15
12 7 / 15 22
ditto. BH-8-9
10 / 15
12 / 15
8 / 15 ditto. 27 BH-8-10
11 / 15
14 15 / 15
10 / 15 ditto. 26 BH-8-11
12 / 15
14 / 15
16
10 / 15 ditto. 28 BH-8-12
13 / 15
15 / 15
18 11 / 15 33
dense. BH-8-13
16 / 15

TEST BORING LOG
BORING NO.: BH-8

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
17 / 15
12 / 15 ditto. 33 BH-8-14
15 / 15
20 18 / 15
13 / 15 ditto. 37 BH-8-15
17 / 15
20 / 15
22
14 / 15 ditto. 40 BH-8-16
18 / 15
22 / 15
24 16 / 15 44
ditto. BH-8-17
20 / 15
24 / 15
17 / 15 ditto. 46 BH-8-18
21 / 15
26 25 / 15
17 / 15 ditto. 49 BH-8-19
22 / 15
27 / 15
28
50 / 8 MH 100 BH-8-20
ELASTIC SILT,
light creamy, hard.
30
END OF BORING.
32
34
36

TEST BORING LOG
BORING NO.: BH-9

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
1 / 15
2 / 15 shells,
SP
POORLY GRADED SAND,
3 / 15 5 BH-9-2
2 3 / 15 loose.
3 / 15 ditto. 7 BH-9-3
3 / 15
4 / 15
4
3 / 15 ditto. 8 13.0 - NP BH-9-4

4 / 15
4 / 15
6 4 / 15 11
5 / 15
6 / 15
5 / 15 ditto. 13 BH-9-6
6 / 15
8 7 / 15
6 / 15 ditto. 16 BH-9-7
7 / 15
9 / 15
10
8 / 15 ditto. 23 BH-9-8
9 / 15
14 / 15
12 9 / 15 24
ditto. BH-9-9
11 / 15
13 / 15
10 / 15 ditto. 25 BH-9-10
12 / 15
14 13 / 15
11 / 15 ditto. 28 BH-9-11
13 / 15
15 / 15
16
10 / 15 ditto. 28 BH-9-12
13 / 15
15 / 15
18 12 / 15 30
dense. BH-9-13
14 / 15

TEST BORING LOG
BORING NO.: BH-9

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
16 / 15
13 / 15 ditto. 32 BH-9-14
15 / 15
20 17 / 15
14 / 15 ditto. 34 BH-9-15
16 / 15
18 / 15
22
15 / 15 ditto. 38 BH-9-16
17 / 15
21 / 15
24 15 / 15 40
ditto. BH-9-17
18 / 15
22 / 15
16 / 15 ditto. 48 BH-9-18
22 / 15
26 24 / 15
17 / 15 ditto. 48 BH-9-19
23 / 15
25 / 15
28
50 / 7 MH 100 BH-9-20
ELASTIC SILT,
light greenish, hard.
30
END OF BORING.
32
34
36

TEST BORING LOG
BORING NO.: BH-10

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
2 / 15
2 / 15 shells,
SP
POORLY GRADED SAND,
4 / 15 8 BH-10-2
2 3 / 15 loose.
3 / 15 ditto. 9 BH-10-3
5 / 15
4 / 15
4
5 / 15 ditto. 9 12.1 - NP BH-10-4

4 / 15
5 / 15
6 3 / 15 13
6 / 15
7 / 15
5 / 15 ditto. 14 BH-10-6
6 / 15
8 8 / 15
6 / 15 ditto. 12 BH-10-7
5 / 15
7 / 15
10
6 / 15 ditto. 17 BH-10-8
8 / 15
9 / 15
12 8 / 15 19
ditto. BH-10-9
8 / 15
11 / 15
9 / 15 ditto. 24 BH-10-10
12 / 15
14 12 / 15
10 / 15 ditto. 26 BH-10-11
13 / 15
13 / 15
16
10 / 15 ditto. 26 BH-10-12
12 / 15
14 / 15
18 12 / 15 37
dense. BH-10-13
17 / 15

TEST BORING LOG
BORING NO.: BH-10

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
20 / 15
14 / 15 ditto. 40 BH-10-14
19 / 15
20 21 / 15
16 / 15 ditto. 41 BH-10-15
19 / 15
22 / 15
22
14 / 15 ditto. 42 BH-10-16
21 / 15
21 / 15
24 17 / 15 43
ditto. BH-10-17
21 / 15
23 / 15
19 / 15 ditto. 49 BH-10-18
23 / 15
26 26 / 15
21 / 15 very dense. 55 BH-10-19

26 / 15
29 / 15
28
50 / 6 MH 100 BH-10-20
ELASTIC SILT,
light creamy, hard.
30
END OF BORING.
32
34
36

TEST BORING LOG
BORING NO.: BH-11

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
2 / 15
2 / 15 shells,
SP
POORLY GRADED SAND,
2 / 15 8 BH-11-2
2 5 / 15 loose.
3 / 15 ditto. 10 BH-11-3
5 / 15
5 / 15
4
4 / 15 ditto. 10 BH-11-4
4 / 15
6 / 15
6 5 / 15 11
5 / 15
6 / 15
6 / 15 ditto. 13 BH-11-6
6 / 15
8 7 / 15
5 / 15 ditto. 15 BH-11-7
7 / 15
8 / 15
10
6 / 15 ditto. 18 BH-11-8
9 / 15
9 / 15
12 7 / 15 21
ditto. BH-11-9
9 / 15
12 / 15
9 / 15 ditto. 23 BH-11-10
10 / 15
14 13 / 15
10 / 15 ditto. 28 BH-11-11
13 / 15
15 / 15
16
11 / 15 dense. 31 BH-11-12
14 / 15
17 / 15
18 13 / 15 33
ditto. BH-11-13
16 / 15

TEST BORING LOG
BORING NO.: BH-11

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
17 / 15
12 / 15 ditto. 36 BH-11-14
17 / 15
20 19 / 15
14 / 15 ditto. 39 BH-11-15
18 / 15
21 / 15
22
15 / 15 ditto. 42 BH-11-16
19 / 15
23 / 15
24 16 / 15 44
ditto. BH-11-17
20 / 15
24 / 15
END OF BORING.
26
28
30
32
34
36

TEST BORING LOG
BORING NO.: BH-12

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
3 / 15
4 / 15 shells,
SP
POORLY GRADED SAND,
5 / 15 14 BH-12-2
2 7 / 15 loose.
6 / 15 ditto. 17 BH-12-3
8 / 15
9 / 15
4
15 BH-12-4
15 MIX OF SAND, SILT, GRAVEL &
15 COBBLES.
6 15 medium dense. BH-12-5

15
15
15 ditto. BH-12-6
15
8 15
15 ditto. BH-12-7
15
15
10
5 / 15 SP 14 BH-12-8
8 / 15 light brown, wet.
12 5 / 15 14
ditto. BH-12-9
7 / 15
7 / 15
6 / 15 ditto. 18 BH-12-10
8 / 15
14 10 / 15
14 / 15 dense. 41 BH-12-11
18 / 15
23 / 15
16
14 / 15 ditto. 40 BH-12-12
18 / 15
22 / 15
18 14 / 15 38
ditto. BH-12-13
16 / 15

TEST BORING LOG
BORING NO.: BH-12

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
21 / 15
15 / 15 ditto. 39 BH-12-14
17 / 15
20 22 / 15
15 / 15 ditto. 42 BH-12-15
18 / 15
26 / 15
22
16 / 15 ditto. 42 BH-12-16
19 / 15
23 / 15
24 17 / 15 43
ditto. BH-12-17
19 / 15
24 / 15
END OF BORING.
26
28
30
32
34
36

TEST BORING LOG
BORING NO.: BH-13

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
2 / 15
3 / 15 shells,
SP
POORLY GRADED SAND,
5 / 15 14 BH-13-2
2 7 / 15 medium dense.
6 / 15 ditto. 17 BH-13-3
8 / 15
9 / 15
4
8 / 15 ditto. 23 BH-13-4
10 / 15
13 / 15
6 9 / 15 27
ditto. BH-13-5
12 / 15
15 / 15
15 BH-13-6
15 MIX OF SAND, SILT, GRAVEL &
8 15 COBBLES.
5 / 15 SP 12 BH-13-7
6 / 15 light brown, medium dense, wet.
10
5 / 15 15 BH-13-8
7 / 15
8 / 15 ditto.
12 7 / 15 18
ditto. BH-13-9
8 / 15
10 / 15
7 / 15 ditto. 20 BH-13-10
9 / 15
14 11 / 15
8 / 15 ditto. 23 BH-13-11
10 / 15
13 / 15
16
11 / 15 dense. 31 BH-13-12
14 / 15
17 / 15
18 16 / 15 35
ditto. BH-13-13
17 / 15

TEST BORING LOG
BORING NO.: BH-13

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
18 / 15
14 / 15 ditto. 39 BH-13-14
18 / 15
20 21 / 15
19 / 15 ditto. 44 BH-13-15
21 / 15
23 / 15
22
22 / 15 ditto. 49 BH-13-16
24 / 15
25 / 15
24 18 / 15 42
ditto. BH-13-17
19 / 15
23 / 15
END OF BORING.
26
28
30
32
34
36

TEST BORING LOG
BORING NO.: BH-14

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
2 / 15
3 / 15 shells,
SP
POORLY GRADED SAND,
3 / 15 9 3.0 - NP BH-14-2
2 5 / 15 loose.
3 / 15 ditto. 10 BH-14-3
4 / 15
6 / 15
4
4 / 15 ditto. 10 BH-14-4
5 / 15
5 / 15
6 4 / 15 13
6 / 15
7 / 15
5 / 15 ditto. 13 BH-14-6
6 / 15
8 7 / 15
5 / 15 ditto. 16 BH-14-7
7 / 15
9 / 15
10
6 / 15 18 BH-14-8
8 / 15
10 / 15 ditto.
12 8 / 15 20
ditto. BH-14-9
9 / 15
11 / 15
9 / 15 ditto. 23 BH-14-10
10 / 15
14 13 / 15
11 / 15 ditto. 28 BH-14-11
14 / 15
14 / 15
16
11 / 15 dense. 32 BH-14-12
15 / 15
17 / 15
18 12 / 15 33
ditto. BH-14-13
15 / 15

TEST BORING LOG
BORING NO.: BH-14

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
18 / 15
14 / 15 ditto. 35 BH-14-14
16 / 15
20 19 / 15
14 / 15 ditto. 39 BH-14-15
18 / 15
21 / 15
22
14 / 15 ditto. 41 BH-14-16
19 / 15
22 / 15
24 16 / 15 44
ditto. BH-14-17
20 / 15
24 / 15
END OF BORING.
26
28
30
32
34
36

TEST BORING LOG
BORING NO.: BH-15

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
2 / 15
1 / 15 shells,
SP
POORLY GRADED SAND,
2 / 15 5 BH-15-2
2 2 / 15 loose.
2 / 15 ditto. 6 BH-15-3
3 / 15
3 / 15
4
3 / 15 ditto. 7 12.5 - NP BH-15-4

3 / 15
4 / 15
6 4 / 15 8
ditto. BH-15-5
4 / 15
4 / 15

5 / 15
8 6 / 15
5 / 15 ditto. 15 BH-15-7
7 / 15
8 / 15
10
5 / 15 18 BH-15-8
8 / 15
10 / 15 ditto.
12 7 / 15 21
ditto. BH-15-9
9 / 15
12 / 15
8 / 15 ditto. 23 BH-15-10
10 / 15
14 13 / 15
END OF BORING.
16
18

TEST BORING LOG
BORING NO.: BH-16

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
0
3 / 15
3 / 15 shells,
SP
POORLY GRADED SAND,
3 / 15 7 BH-16-2
2 4 / 15 loose.
2 / 15 ditto. 7 BH-16-3
3 / 15
4 / 15
4
4 / 15 ditto. 9 BH-16-4
5 / 15
4 / 15
6 4 / 15 12 12.6 - NP
5 / 15
7 / 15
5 / 15 ditto. 14 BH-16-6
6 / 15
8 8 / 15
6 / 15 ditto. 16 BH-16-7
7 / 15
9 / 15
10
8 / 15 20 BH-16-8
10 / 15
10 / 15 ditto.
12 9 / 15 24
ditto. BH-16-9
11 / 15
13 / 15
10 / 15 ditto. 29 BH-16-10
14 / 15
14 15 / 15
11 / 15 ditto. 28 BH-16-11
12 / 15
16 / 15
16
12 / 15 ditto. 26 BH-16-12
12 / 15
14 / 15
18 13 / 15 37
dense. BH-16-13
18 / 15

TEST BORING LOG
BORING NO.: BH-16

SOIL SYMBOLS, CURVE
DEPTH
AND TEST DATA
20 40 60 80
19 / 15
12 / 15 ditto. 38 BH-16-14
17 / 15
20 21 / 15
14 / 15 ditto. 41 BH-16-15
18 / 15
23 / 15
22
16 / 15 ditto. 42 BH-16-16
18 / 15
24 / 15
24 15 / 15 44
ditto. BH-16-17
21 / 15
23 / 15
END OF BORING.
26
28
30
32
34
36

SOIL ELECTRICAL RESISTIVITY TEST
Wenner's procedure (ASTM-G57)
PROJECT Proposed Grain Terminal DATE 08-08-2022
CLIENT United Feed Co. Ltd. REF. KSM-4463
LOCATION Ras Al Khair, Kingdom of Saudi Arabia TEST DIRECTION (4 Directions)
EQUPMENT GRT300 TEST NO. 1
SR. NO. STR. LOCATION NORTHING EASTING

ER-1 ER-1 3050081.081 321028.899
ELECTRODE RESISTANCE RESISTIVITY = 2ΠaR

SPACING (M) (R) (ρ)
(OHMS) (OHM-M)
(a)
N S E W N S E W
1.5 1.00 0.95 0.90 1.00 9.42 8.95 8.48 9.42

3 0.85 0.60 0.70 0.80 16.02 11.31 13.19 15.08
5 0.70 0.50 0.60 0.60 21.99 15.71 18.85 18.85
8 0.45 0.30 0.40 0.40 22.62 15.08 20.11 20.11
10 0.25 0.10 0.10 0.30 15.71 6.28 6.28 18.85
12 0.04 0.08 0.09 0.09 3.02 6.03 6.79 6.79
Description : Site is generally flat.
100.00
Pa OHM-METER
10.00
1.00
1 AB / 3 ( m)
10
APPENDIX II
LABORATORY TEST RESULTS
Particle Sieve Analysis of Soil
1-1/2 in.
3/4 in.
1/2 in.
3/8 in.
#100
#140
#200
6 in.
3 in.
2 in.
1 in.
#10
#20
#30
#40
#60
#4
100
90
80
70
PERCENT FINER
60
50
40
30
20
10
0
500 100 10 1 0.1 0.01 0.001
GRAIN SIZE - mm
% COBBLES % GRAVEL % SAND % SILT % CLAY
0.0 0.0 95.2 4.8
SIEVE PERCENT SPEC.* PASS? Soil Description

SIZE FINER PERCENT (X=NO) Poorly Graded Sand
3/8 in. 100.0
#4 100.0
#10 100.0
#40 89.2 Atterberg Limits
#200 4.8 PL= - LL= - PI= NP
Coefficients
D85= 0.388 D60= 0.228 D50= 0.186
D30= 0.124 D15= 0.0919 D10= 0.0832
Cu= 2.74 Cc= 0.81
Classification
USCS= SP AASHTO= A-3
Remarks
* (no specification provided)

Sample No.: BH-1 Source of Sample: SPT SAMPLE Date: 27-08-2022
Location: Elev./Depth: 22.50M
Client: UNITED FEED CO. LTD.

Project: PROPOSED GRAIN TERMINAL PROJECT
LOCATED AT RAS AL KHAIR, K.S.A.
Project No: KSM-4463 Figure
1-1/2 in.
3/4 in.
1/2 in.
3/8 in.
#100
#140
#200
6 in.
3 in.
2 in.
1 in.
#10
#20
#30
#40
#60
#4
100
90
80
70
PERCENT FINER
60
50
40
30
20
10
0
500 100 10 1 0.1 0.01 0.001
GRAIN SIZE - mm
0.0 0.0 12.9 87.1

SIZE FINER PERCENT (X=NO) Elastic Silt
#4 100.0
#10 100.0
#40 92.9
PL= 86 LL= 144 PI= 58
Coefficients
D85= D60= D50=
D30= D15= D10=
Cu= Cc=
Classification
USCS= MH AASHTO= A-7-5(72)
Remarks


1-1/2 in.
3/4 in.
1/2 in.
3/8 in.
#100
#140
#200
6 in.
3 in.
2 in.
1 in.
#10
#20
#30
#40
#60
#4
100
90
80
70
PERCENT FINER
60
50
40
30
20
10
0
500 100 10 1 0.1 0.01 0.001
GRAIN SIZE - mm
0.0 0.0 99.2 0.8

SIZE FINER PERCENT (X=NO) Poorly Graded Sand with sea shells
3/8 in. 100.0
#4 100.0
#10 99.4
#200 0.8 PL= - LL= - PI= NP
Coefficients
D85= 1.54 D60= 0.955 D50= 0.776
D30= 0.477 D15= 0.277 D10= 0.209
Cu= 4.56 Cc= 1.14
Classification
USCS= SP AASHTO= A-1-b
Remarks


1-1/2 in.
3/4 in.
1/2 in.
3/8 in.
#100
#140
#200
6 in.
3 in.
2 in.
1 in.
#10
#20
#30
#40
#60
#4
100
90
80
70
PERCENT FINER
60
50
40
30
20
10
0
500 100 10 1 0.1 0.01 0.001
GRAIN SIZE - mm
0.0 0.0 95.5 4.5

3/8 in. 100.0
#4 100.0
#10 98.1
#200 4.5 PL= - LL= - PI= NP
Coefficients
D85= 0.476 D60= 0.226 D50= 0.181
D30= 0.121 D15= 0.0912 D10= 0.0831
Cu= 2.73 Cc= 0.78
Classification
Remarks


1-1/2 in.
3/4 in.
1/2 in.
3/8 in.
#100
#140
#200
6 in.
3 in.
2 in.
1 in.
#10
#20
#30
#40
#60
#4
100
90
80
70
PERCENT FINER
60
50
40
30
20
10
0
500 100 10 1 0.1 0.01 0.001
GRAIN SIZE - mm
0.0 0.0 96.8 3.2

3/8 in. 100.0
#4 100.0
#10 100.0
#200 3.2 PL= - LL= - PI= NP
Coefficients
D85= 0.402 D60= 0.235 D50= 0.191
D30= 0.128 D15= 0.0947 D10= 0.0858
Cu= 2.74 Cc= 0.81
Classification
Remarks


1-1/2 in.
3/4 in.
1/2 in.
3/8 in.
#100
#140
#200
6 in.
3 in.
2 in.
1 in.
#10
#20
#30
#40
#60
#4
100
90
80
70
PERCENT FINER
60
50
40
30
20
10
0
500 100 10 1 0.1 0.01 0.001
GRAIN SIZE - mm
0.0 0.0 95.7 4.3

3/8 in. 100.0
#4 100.0
#10 98.7
#200 4.3 PL= - LL= - PI= NP
Coefficients
D85= 0.486 D60= 0.230 D50= 0.184
D30= 0.122 D15= 0.0917 D10= 0.0835
Cu= 2.76 Cc= 0.78
Classification
Remarks


1-1/2 in.
3/4 in.
1/2 in.
3/8 in.
#100
#140
#200
6 in.
3 in.
2 in.
1 in.
#10
#20
#30
#40
#60
#4
100
90
80
70
PERCENT FINER
60
50
40
30
20
10
0
500 100 10 1 0.1 0.01 0.001
GRAIN SIZE - mm
0.0 0.0 96.5 3.5

3/8 in. 100.0
#4 100.0
#10 100.0
#200 3.5 PL= - LL= - PI= NP
Coefficients
D85= 0.355 D60= 0.218 D50= 0.180
D30= 0.124 D15= 0.0931 D10= 0.0848
Cu= 2.58 Cc= 0.82
Classification
Remarks


1-1/2 in.
3/4 in.
1/2 in.
3/8 in.
#100
#140
#200
6 in.
3 in.
2 in.
1 in.
#10
#20
#30
#40
#60
#4
100
90
80
70
PERCENT FINER
60
50
40
30
20
10
0
500 100 10 1 0.1 0.01 0.001
GRAIN SIZE - mm
0.0 0.0 97.6 2.4

3/8 in. 100.0
#4 100.0
#10 100.0
#200 2.4 PL= - LL= - PI= NP
Coefficients
D85= 0.382 D60= 0.230 D50= 0.188
D30= 0.128 D15= 0.0955 D10= 0.0868
Cu= 2.65 Cc= 0.82
Classification
Remarks


1-1/2 in.
3/4 in.
1/2 in.
3/8 in.
#100
#140
#200
6 in.
3 in.
2 in.
1 in.
#10
#20
#30
#40
#60
#4
100
90
80
70
PERCENT FINER
60
50
40
30
20
10
0
500 100 10 1 0.1 0.01 0.001
GRAIN SIZE - mm
0.0 0.0 96.0 4.0

3/8 in. 100.0
#4 100.0
#10 97.9
#200 4.0 PL= - LL= - PI= NP
Coefficients
D85= 0.512 D60= 0.235 D50= 0.187
D30= 0.124 D15= 0.0925 D10= 0.0841
Cu= 2.80 Cc= 0.77
Classification
Remarks



CHEMICAL ANALYSIS TEST RESULTS

(2:1 WATER : SOIL AQUEOUS EXTRACT)
PROJECT Ras Al Khair Grain Terminal Project REF NO. KSM-4463
LOCATION Ras Al Khair, K.S.A. DATE 26-08-2022
SAMPLE NO. BH-1 BH-5 BH-8 BH-12

DEPTH (M) 0.00 1.50 0.00 1.50
SOIL
Ph 7.15 7.20 7.10 7.13
SAMPLE
Total Sulphate (%) 0.110 0.094 0.130 0.081
Total Chloride (%) 0.350 0.200 0.310 0.264
SAMPLE NO. BH-2

DEPTH (M) --
WATER
Ph 7.20
SAMPLE
Total Sulphate (%) 2.760
Total Chloride (%) 5.490
REQUIREMENTS FOR SUBSURFACE CONCRETE

Concentration of Salts Requirement for dense
Expressed as SO3 and NaCI fully compacted
In Soil In concrete made with
Minimum
Groundwater nominal max. size
depth of
aggregate complying
Class TYPE OF CEMENT cover for
with the requirement reinforced
BS 882 or ASTM C 30 concrete
Total Total Total Total Cementitous Free water (20 mm
Content not cement agg.)
SO3 NaCI SO3 NaCI
less than: ratio: not
(%) (%) gm/L gm/L (Kg/M3) more than
1 <0.20 <0.05 <0.30 <2.5 All cement (BS 4027 300 0.50 40
ASTM C 150 Type 1
or V blended
containing pfa or slag
2 0.2- 0.05- 0.3- 2.5- BS 12 or ASTM C 300 0.50 40
0.5 0.1 1.2 5.0 150, Type 1 cement
blended with minimum
of 25% or maximum of
40% pfa (ASTM C 595
Type 1,2 (MS)
Cements
BS 4027 or 4248, 300 0.50
Type V cement
3 0.5- 0.1- 1.2- 5.0-10 BS 12 or ASTM C 400 0.40 60
1.0 0.2 2.5 150, Type 1 cements
blended with minimum
of 40 pfa. ASTM C
595, Type 12 MS
Cements
BS 4027 or BS 4028 360 0.45
ASTM Type V
cements


4 1.0- 0.2- 2.5- 10-30 BS 4027 or BS 4028 400 0.40 75

2.0 0.5 5.0 ASTM Type V
cements
Over Over Over Over BS 4027 or BS 4028 400 0.40 100
5 2.0 0.5 5.0 30 ASTM Type V
cements
Value expressed as percentages by mass of total content of cementitious material.
NOTE # 1: If the concentration of NaCI gives a higher class rating that the concentration of SO3,
then the higher class shall be used and vice versa.
NOTE # 2: The cement contents given in the table relate to 20 mm nominal maximum size
aggregate. In order to maintain the content of the mortar fraction at similar values, the
minimum cement content given above should be increased by 50 kg/m3 for 10mm
nominal size aggregate and may be decreased by 30 kg/m3 for 40 mm nominal size
aggregate.
NOTE # 3: Different aggregate require different water contents to produce concrete of the same
workability and therefore a range of free water/cement ratio is applicable to each
cement content. In order to achieve satisfactory workability at specified maximum
free water/cement ratio, it may be necessary to increase the cement content above
the minimum specified or use water-reducing admixtures.
NOTE # 4: Pulverized fly ash (pfa) should comply with BS 3892 or the appropriate part of ASTM
C 595. Ground granulated blastfurnace slag should comply with BS 0002, or the
appropriate part of ASTM C 595.
NOTE # 5: Minimum depth of cover apply to concrete with 20 mm maximum size aggregate. In
no case should the cover be less than the maximum size of aggregate size. Minimum
cover includes cover to links, etc.
NOTE # 6: Concrete exposed to moisture in class 3, 4 or 5 environment should by subject of a

additional requirement of a maximum water penetration of 30 mm at 28 days age
when tested by the DIN 1048 test method for impermeability.
NOTE # 7: Concrete exposed to wetting & drying by irrigation water should be rated Class 2 as a
minimum requirement.
SOURCE: CIRIA Special Publication No. 31, CIRIA Guide to Concrete Construction in the Gulf
Region, Construction Industries Research and Information Association, London.


THERMAL RESISTIVITY TEST RESULT
PROJECT Ras Al Khair Grain Terminal
DATE 26/8/2022
CLIENT United Feed Co. Ltd.
LOCATION Ras Al Khair, Kingdom of Saudi Arabia REF NO. KSM-4463
ATTERBEG'S THERMAL RESISTIVITY

DEPTH % PASSING -
SAMPLE DESCRIPTION LIMITS ( Cº cm/watt)
(M) #4 #40 #200 LL % PI % - M.C. 1 % M.C. 2%
LIGHT BROWN, POORLY

TR-1 0.50-1.00 100 98.0 1.3 NP - 190 93.5
GRADED SAND WITH SILT
- - - - - - - - -
APPENDIX III
GUIDE SPECIFICATIONS FOR

ENGINEERED FILL
GENERAL GUIDE SPECIFICATIONS FOR ENGINEERED FILL
A. GENERAL CONDITION
Definition of Terms
FILL ......... is all soil and soil-rock material placed to raise the grade of the site or to backfill excavation.
ON-SITE MATERIAL ... is that which is obtained from the required excavation on the site.
IMPORT MATERIAL ... is that hauled in from off-site areas.
SELECT MATERIAL ... is a soil material meeting the requirements set for in C (2) below.
ENGINEERED FILL ... is a fill upon which the Soil Engineer has made sufficient tests and
observations to enable him to issue a written statement that in his opinion the fill has been placed and
compacted in accordance with the specifications requirements.
AASHTO SPECIFICATIONS. are the latest of the Standard Specifications of the American
Association of State Highway and Transport Officials.
ASTM SPECIFICATIONS .. are those of the American Society for Testing and Materials.
DEGREE OF COMPACTION... is the ratio, expressed as a percentage, of the dry density of the fill
material as compacted in the field to the maximum dry density of the same material determined by
AASHTO Test Designation T180 or by ASTM D-1557-90 test, "Moisture-Density Relation of Soils using
a 10 lb. Hammer and an 18-in. Drop", or AASHTO Test Designation T-90 or ASTM D-698-90 using a
5.5 lb. hammer and 12 in drop.
Soil Engineering Inspections
The Soil Engineer shall be the contractor or Owner's representative to observe the grading operations
both during preparation of the site and the construction of any engineered fill. He shall make a
sufficient number of field observation and tests to enable him to form an opinion regarding the
adequacy of the site preparation, the acceptability of the fill materials, and the extent to which the
degree of compaction of the fill, as placed, meets the specification requirements. Any fill that does not
meet the specification requirements shall be removed and/or recompacted until the requirements are
satisfied.
Soil Investigation
A Soil Investigation has been performed for this site. A report of this investigation is available to the
Contractor upon request. The Contractor shall familiarize with the soil conditions at the site whether
covered in the report or not, and shall thoroughly understand all recommendations associated with
grading.
B. SITE PREPARATION
Excavation
All excavation shall be carefully made true to the grades and elevations shown on the plans. The
excavated surfaces shall be kept properly graded to provide good drainage during construction and
prevent pending of water.
Preparation for Filling
All vegetation, organic top-soil and debris shall be stripped from the site. The stripping depth shall be
determined by the supervising Soil Engineer in the field. The stripped material shall either be removed
from the site or stockpiled for re-use later, but none of the stripped material contaminated by organic
matter may be used for engineered fill.
Any soft areas exposed after stripping shall be over-excavated. all visual or unseen channels or
ditches shall be over-excavated to the depth of firm material and to the width of the compacting
equipment.
After being stripped and over-excavated, the upper 15cm below the exposed surfaces shall be
compacted to a moisture content that will permit proper compaction as hereinafter specified for
fill. Before placing the fill, the contractor shall obtain the soil Engineer's approval of the site
preparation in the area to be filled. The requirements of this section may be omitted only when
approved in writing by the soil Engineer.
C. MATERIAL USED FOR FILL
1. General Requirement for Fill Materials
All fill material must be approved by the soil Engineer. The material shall be a soil or soil rock
mixture which is free from organic matter or other deleterious substances. The fill material shall
not contain rock or lumps over 15 cm in greatest dimension, and not more than 15 percent larger
than 6.5 cm. In addition, the maximum size of rock or lumps shall be less than 10 cm in back fill
materials. Excavated on-site materials, if free of organic or other deleterious substances, are
suitable for use in fills, except where select material is specified.
2. Requirements for select fill Material
In addition to the requirement of C.1 above, select material must conform to the following:
Maximum Plasticity Index 12%
3. Engineering Fill Material

A-1-a A-1-b
Sieve Analysis (%passing)
No. 10 sieve 50 max
No. 40 sieve 30 max 50 max
No. 200 sieve 15 max 25 max
Maximum Plasticity Index (PI) 6 6
Usual Type of Material Stone fragments gravel and sand
D. PLACING AND COMPACTING FILL MATERIAL
All fill material shall be compacted as specified below, or by other methods, if approved by the
Soil engineer, so as to produce a minimum degree of compaction of 95 percent, except in clean
sands and gravels. These materials shall be compacted to a minimum degree of compaction of 95
percent. Clean sands and gravel fill shall be defined as cohesionless granular material meeting
the following requirements; in addition to the requirements of C.1 above:
Minimum Sand Equivalent 25

Maximum Plasticity index 6
Maximum percentage by Dry

Weight passing #200 sieve 15
Fill material shall be spread in uniform lifts not exceeding thickness that achieves the desired
degree of compaction (generally 20 cm uncompacted thickness is acceptable). Before
compaction begins, the fill shall be brought to the required moisture content by either: (1)
aerating the material if it is too wet; (2) spraying the material with water if it is too dry. Each lift
shall be thoroughly mixed before compaction to ensure a uniform distribution of water content.
Appropriate water content will be determined by ASTM D 1557-90 and/or ASTM D 690-90
E. TREATMENT AFTER COMPLETION OF GRADING
After grading is completed and the Soil Engineer has finished his inspect of the work, no further
excavation shall be done except with the approval of and under the observation of the soil
engineer.
It shall be the responsibility of the Grading contractor to prevent erosion of freshly graded areas
during construction and until such time as permanent drainage and erosion control measures have
been installed.
APPENDIX IV
SEISMIC MAP & GEOLOGICAL MAP
APPENDIX V
PHOTOGRAPHS
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
KSM-4463
APPENDIX VI
GEOTECHNICAL CALCULATIONS
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static
Vertical Load, Q= 5000.0 -kN

Shear Load, P= 0.0 -kN
Moment, M= 0.0 -kN-m
Profile:
Pile Length, L= 35.0 -m
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0
Nocontributing Zone, Ln1=Ln2=Ln3=0.
Drilled Shaft (dia >24 in. or 61 cm)
Soil Data: Pile Data:

Depth Gamma Phi C K e50 or Dr Nspt Depth Width Area Per. I E Weight
-m -kN/m3 -kN/m2 -MN/m3 % -m -cm -cm2 -cm -cm4 -MP -kN/m
0 19.3 32 0.0 43.6 65.70 30 0.0 120 11309.7 377.0 10178760.020683 26.691
2 9.5 32 0.0 25.9 65.70 30 35.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
Weight above Ground= 0.00 Total Weight= 568.81-kN *Soil Weight is not included
Side Resistance (Down)= 7212.507-kN Side Resistance (Up)= 5164.040-kN
Tip Resistance (Down)= 1017.873-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down)= 8230.380-kN Total Ultimate Capacity (Up)= 5732.850-kN
Total Allowable Capacity (Down)= 5147.629-kN Total Allowable Capacity (Up)= 3150.830-kN
OK! Qallow > Q
Settlement Calculation:
At Q= 5000.00-kN Settlement= 0.64100-cm
At Xallow= 2.50-cm Qallow= 8120.85889-kN
Note: If program can't find result or the result exceeds the up limits. The result shows 9999.
CivilTech KSM- 4463

Software
Loads:

Profile:
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0

0 19.3 32 0.0 43.6 65.70 30 0.0 120 11309.7 377.0 10178760.020683 26.691
2 9.5 32 0.0 25.9 65.70 30 30.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
OK! Qallow > Q
CivilTech KSM- 4463

Software
Loads:

Profile:
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0

0 19.3 32 0.0 43.6 65.70 30 0.0 120 11309.7 377.0 10178760.020683 26.691
2 9.5 32 0.0 25.9 65.70 30 25.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
OK! Qallow > Q
CivilTech KSM- 4463

Software
Loads:

Profile:
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0

0 19.3 32 0.0 43.6 65.70 30 0.0 100 7854.0 314.2 4908738.5 20683 18.535
2 9.5 32 0.0 25.9 65.70 30 35.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
OK! Qallow > Q
CivilTech KSM- 4463

Software
Loads:

Profile:
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0

0 19.3 32 0.0 43.6 65.70 30 0.0 100 7854.0 314.2 4908738.5 20683 18.535
2 9.5 32 0.0 25.9 65.70 30 30.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
OK! Qallow > Q
CivilTech KSM- 4463

Software
Loads:

Profile:
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0

0 19.3 32 0.0 43.6 65.70 30 0.0 100 7854.0 314.2 4908738.5 20683 18.535
2 9.5 32 0.0 25.9 65.70 30 25.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
OK! Qallow > Q
CivilTech KSM- 4463

Software
Loads:

Profile:
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0

0 19.3 32 0.0 43.6 65.70 30 0.0 100 7854.0 314.2 4908738.5 20683 18.535
2 9.5 32 0.0 25.9 65.70 30 25.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
OK! Qallow > Q
CivilTech KSM- 4463

Software
Loads:

Profile:
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0

0 19.3 32 0.0 43.6 65.70 30 0.0 80 5026.5 251.3 2010619.3 20683 11.863
2 9.5 32 0.0 25.9 65.70 30 35.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
OK! Qallow > Q
CivilTech KSM- 4463

Software
Loads:

Profile:
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0

0 19.3 32 0.0 43.6 65.70 30 0.0 80 5026.5 251.3 2010619.3 20683 11.863
2 9.5 32 0.0 25.9 65.70 30 30.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
OK! Qallow > Q
CivilTech KSM- 4463

Software
Loads:

Profile:
Top Height, H= 0 -m
Slope Angle, As= 0
Batter Angle, Ab= 0

0 19.3 32 0.0 43.6 65.70 30 0.0 80 5026.5 251.3 2010619.3 20683 11.863
2 9.5 32 0.0 25.9 65.70 30 25.0
28.5 12.2 0 100 666.7 0.33 50
Vertical capacity:
OK! Qallow > Q
CivilTech KSM- 4463

Software

Soil Report KSM 4463 11-09-22

Uploaded by

Copyright:

Available Formats

Soil Report KSM 4463 11-09-22

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Soil Report KSM 4463 11-09-22

Uploaded by

Copyright:

Available Formats

SOIL & FOUNDATION CO. LTD.

97 Prince Sultan Rd. Doha Dt.

GEOTECHNICAL INVESTIGATION FOR THE PROPOSED

UNITED FEED CO. LTD.

August 30, 2022 Ref: KSM-4463

UNITED FEED CO. LTD.

Thank you and best regards,

SOIL & FOUNDATION CO., LTD.

Engr. Hesham Azam

2.0 SITE DESCRIPTION 2

3.0 PROJECT DESCRIPTION 2

4.0 REGIONAL GEOLOGY 2

5.0 FIELD INVESTIGATION 3

6.0 LABORATORY OBSERVATIONS 4

7.0 GEOTECHNICAL CONDITION 5

7.1 Subsurface Formation 5

8.0 GEOTECHNICAL RECOMMENDATIONS 8

8.1 Foundation Details 8

APPENDIX I FIELD INVESTIGATIONS

Table 1 Summary of S.P.T. N Values, R.Q.D. Values and Sub-surface Formations

Figure No. 1 Site Plan and Location of Boreholes

Figure No. 2-17 Logs of Test Boring No. BH-1 to BH-16

APPENDIX II LABORATORY TEST RESULTS AND CURVES

APPENDIX III GUIDE SPECIFICATIONS FOR ENGINEERED FILL

APPENDIX IV SEISMIC MAP & GEOLOGICAL MAP

RAS AL KHAIR GRAIN TERMINAL PROJECT

(RAS AL KHAIR, EASTERN PROVINCE)

THE KINGDOM OF SAUDI ARABIA

Eastern Province, the Kingdom of Saudi Arabia.

The purpose of this geotechnical investigation is to determine the depth and

characteristics of the different subsurface formations and recommended

allowable bearing capacity and expected settlements under the proposed

This report includes guidelines for earthwork construction specification, site

and structure descriptions, field investigation, laboratory observations,

subsurface formations and geotechnical recommendation.

at Ras Al Khair, Eastern Province, Kingdom of Saudi Arabia. Figure 1 in

Appendix I presents the site plan with boreholes locations.

3.0 PROJECT DESCRIPTION

project consists of Storage Silos, Flat Store Warehouse, Bagging Station,

Flakes/Transfer Tower, Ship Unloading Conveyor & Unloader and Weight

Bridge Scale House

4.0 REGIONAL GEOLOGY

(Qs) and associated fine sediments including caliche-like and gypsiferous

deposits in undrained depression; gravel composed chiefly of limestone and

other rocks of local origin, includes older gravels in some areas.

performed on August 13-24, 2022. Sixteen (16) exploratory borings were

geotechnical needs of the project as can be seen in Figure 1 Appendix I. Both

The log of the borehole is shown in Appendix I, wherein a continuous profile of

each borehole was prepared by an experienced engineering geologist to

present clearly all the subsurface soils encountered.

Soil samples were collected at frequent intervals using a standard 50 mm

(outside diameter) split-spoon sampler driven with a 63.5 kg automatic

hammer with a drop height of 0.76 m in accordance with the Standard

Penetration Test (SPT) procedures (ASTM D 1586-11).

properties (After Peck et al., 1974).

properties (After Peck et al., 1974).

Table 1 SPT Correlation

Granular Soil Cohesive Soil