Scribd Logo
Upload

Welcome to Scribd!

  • 105 views

    Luggage Security Project

    Uploaded by

    TI Nafis
    The document proposes a luggage security alarm circuit using logic gates that generates a warning alarm when someone tries to lift the luggage. The circuit uses a CD4011 IC, resistors, capacitors, a transistor, and relay. It produces a warning beep when the wire loop attached to the luggage is broken, indicating an attempt to unlock it. The circuit also includes a photoresistor to automatically detect night and day and turn lights on/off accordingly. The total expected cost of components is approximately 1,500 BDT. The proposed application is to add security to luggage while traveling and prevent robbery attempts at homes.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Luggage Security Project

    Uploaded by

    TI Nafis
    105 views4 pages
    The document proposes a luggage security alarm circuit using logic gates that generates a warning alarm when someone tries to lift the luggage. The circuit uses a CD4011 IC, resistors, capacitors, a transistor, and relay. It produces a warning beep when the wire loop attached to the luggage is broken, indicating an attempt to unlock it. The circuit also includes a photoresistor to automatically detect night and day and turn lights on/off accordingly. The total expected cost of components is approximately 1,500 BDT. The proposed application is to add security to luggage while traveling and prevent robbery attempts at homes.

    Original Title

    Luggage Security Project (1).docx

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document proposes a luggage security alarm circuit using logic gates that generates a warning alarm when someone tries to lift the luggage. The circuit uses a CD4011 IC, resistors, capacitors, a transistor, and relay. It produces a warning beep when the wire loop attached to the luggage is broken, indicating an attempt to unlock it. The circuit also includes a photoresistor to automatically detect night and day and turn lights on/off accordingly. The total expected cost of components is approximately 1,500 BDT. The proposed application is to add security to luggage while traveling and prevent robbery attempts at homes.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    105 views4 pages

    Luggage Security Project

    Uploaded by

    TI Nafis
    The document proposes a luggage security alarm circuit using logic gates that generates a warning alarm when someone tries to lift the luggage. The circuit uses a CD4011 IC, resistors, capacitors, a transistor, and relay. It produces a warning beep when the wire loop attached to the luggage is broken, indicating an attempt to unlock it. The circuit also includes a photoresistor to automatically detect night and day and turn lights on/off accordingly. The total expected cost of components is approximately 1,500 BDT. The proposed application is to add security to luggage while traveling and prevent robbery attempts at homes.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Group – 02 Project Proposal

    Luggage Security Alarm with


    Light Monitoring Project using Logic Gate
    Introduction:
    During our journey by train and bus, we carry many important things and all the time we fear that someone
    might lift our luggage. So, to protect our baggage, we normally lock our baggage through old ways by the
    help of chains and locks. After all locks, we remain in fear that someone may slash the chain and take away
    our valuable material. To overcome this fear, here is an easy circuit which is based on the NAND gate. In this
    circuit, when someone tries to lift your luggage, it will generate a warning alarm which is very much helpful
    during your travel in the bus or train even at the night time as it can also produce audio visual indication
    attached to the relay. We may attach a light detector to monitor the system.

    Objective:
    ● The main objective of the Day Night indicator circuit is to help us to turn on the lights as the night
    falls automatically. And as the dawn sets in, the Day and Night indicator automatically get switched
    off.
    ● The main objective of Luggage Security circuit is to generate an alarm when any unauthorised
    person tries to steal one's luggage. This system is extremely useful to travel at night time. Another
    application of this luggage security alarm is, one can use at home for the security from the theft.

    Required Component:
    Component Name Type Number
    IC CD4011 1
    4011 1
    300 Ω 3
    1KΩ 3
    Resistor 4.7KΩ 3
    6.8KΩ 3
    33KΩ 3
    Capacitor 0.1 µF 3
    Luggage/ Safe - 1
    Relay 1
    Miscellaneous T(BC547) 1
    D(1N4007) 5
    LED 5V/30mA 1
    Photoresistor GL5537 1
    Battery 9V 1
    Jumper wire - 1
    Alarm( Buzzer) 1
    Circuit Diagram:

    Luggage Security Alarm Circuit Description:

    The basic building block of this circuit is CD4011 along with some other components viz. resistors, capacitor
    along with transistor and relay which is used to save your important things from robbery with the help of
    this easy circuit. It produces a warning beep, when someone tries to unlock the lock as an effect of its wire
    loop will split and alarm is produced.
    To get familiar with the working, you should get aware with the NAND gate truth table which is shown
    below –

    NAND Gate – Truth Table


    Expected Outcome:
    When any of the input states or both the input states go to the low state in the NAND gate, then the output
    will be high and if both the inputs are at high state, then the output will be low in that case.
    CD4011 is the used CMOS (Complementary Metal Oxide Semiconductor) chip. It arrives in a Dual Inline
    Package (DIP) of 14 pin. There is a small notch present on the chip at one of the corners which is recognized
    as pin 1. In a single chip, it is a group of 4 NAND gates which are independent of each other. Each gate is a
    three-terminal device with 2 terminals for the input purpose and one is for the output purpose. 5V to 16V
    is the working voltage range of the IC. Approximately 10mA of current at 12 V is delivered by the IC which
    can be trimmed down with the reduction of the power supply voltage.
    Functioning of these circuits is quite easy when we will receive; output is based on the voltage on pin 5. At
    the time when the power supply is attached to the circuit pin 5, voltage is at zero as the loop is unbroken.
    Hence at pin 4, voltage is high which is coupled with pin1 and pin 2 which is also at high state. As we can
    also find from the truth table of the NAND gate that if both the inputs are at high state, then the output is
    low hence at the pin 3 of gate 1, we get low which is once more attached to pin 12 as well as 13 moving
    them also to the low which in turn makes the pin 11 to switch at high switching pin 8 as well as pin 9 also at
    high and low voltage at pin 10 due to this transistor linked to it via a resistor will not boost the base of it
    and the alarm will not receive by us. This implies that our baggage is secure.
    The component that will allow us to detect light is a photoresistor. We will use a photoresistor's
    light-sensing ability to detect whether the circuit is exposed to darkness or bright light. How this works is
    that a photoresistor's resistance changes in proportion to the amount of light it is exposed to. In darkness,
    it has remarkably high resistance. In bright light, its resistance drops dramatically. If placed in a voltage
    divider circuit with a fixed resistor, we can exploit this resistance-altering behaviour so that when
    connected to a NAND gate, we can produce a HIGH output when the photoresistor is exposed to bright
    light and a LOW output when the photoresistor is exposed to darkness. All of this will be explained in detail
    below how exactly this works. But realise that a photoresistor's resistance-changing ability allows us to
    distinctly know whether it is exposed to darkness or bright light. Knowing this, we can effectively build a
    night light circuit.

    Expected Cost:
    Component Name Type Number Price (BDT)
    IC CD4011 1 100
    4011 1
    300 Ω 3
    1KΩ 3
    Resistor 4.7KΩ 3 60
    6.8KΩ 3
    33KΩ 3
    Capacitor 0.1 µF 3 30
    Luggage/ Safe - 1 800
    Relay 1 340
    Miscellaneous T(BC547) 1 10
    D(1N4007) 5 05
    LED 5V/30mA 1 20
    Photoresistor GL5537 1 50
    Battery 9V 1 120
    Jumper wire - 1 30
    Conclusion: Application of this circuit is that you can employ these into your house to avoid the attempt
    of robbery in our luggage with the help of this alarm circuit. When anyone tries to open the door of your
    house, the loop breaks down and sound from the alarm produces. It will also allow the user to use it at
    nights which the circuit will allow to generate light automatically. And turn off the light when it is not
    required.

    Student ID:
    ● 200908
    ● 200910
    ● 200912
    ● 200913
    ● 200914

    You might also like