Operating manual Getting started, IRC5 and RobotStudio Online

Document ID: 3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

The information in this manual is subject to change without notice and should not be construed as a commitment by ABB. ABB assumes no responsibility for any errors that may appear in this manual. Except as may be expressly stated anywhere in this manual, nothing herein shall be construed as any kind of guarantee or warranty by ABB for losses, damages to persons or property, fitness for a specific purpose or the like. In no event shall ABB be liable for incidental or consequential damages arising from use of this manual and products described herein. This manual and parts thereof must not be reproduced or copied without ABB's written permission, and contents thereof must not be imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted. Additional copies of this manual may be obtained from ABB at its then current charge.
Copyright 2007 ABB. All rights reserved.

Copyright 2007 ABB All rights reserved. ABB Robotics SE-721 68 Vsters Sweden

Table of Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1 Procedures 7

1.1 Procedure for single robot systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1.2 Procedure for MultiMove systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.3 Common procedures for all systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 General 17

2.1 What you need to get the system started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.2 What is a FlexPendant? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2.3 What is RobotStudio Online? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2.4 What is RobotWare?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.5 About the media pool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 2.6 When to use the FlexPendant and RobotStudio Online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 2.7 Product documentation, M2004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Copyright 2007 ABB. All rights reserved.

3HAC 027097-001 Revision: -

Table of Contents

3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

Overview

Overview
About this manual This manual is to be used when starting up the system for the very first time. It contains excerpts from other documents included in the robot system delivery. Usage This manual contains instructions for starting up the IRC5 robot controller for the very first time after the physical installation has been completed. Who should read this manual? This manual is intended for: Prerequisites The reader should be familiar with: mechanically installing the robot hardware be trained in robot operation Commissioning personnel

The contents of the manual assumes all hardware (manipulator, controller and such) has been installed correctly and connected to each other. Organization of chapters The manual is organized in the following chapters: Chapter
1. Procedures 2. General

Contents
Procedures for setup and startup of the IRC5 robot system. Descriptions of the parts in IRC5 robot system.

References
Copyright 2007 ABB. All rights reserved.

Reference
Product manual - IRC5 Operating manual - IRC5 with FlexPendant Operating manual - RobotStudio Online Operating manual - Trouble shooting Technical reference manual - System parameters Application manual - MultiMove

Document Id
3HAC021313-001 3HAC16590-1 3HAC18236-1 3HAC020738-001 3HAC17076-1 3HAC021272-001

Revisions Revision Description

Replaces manual with document id 3HAC 021564-001. Released with RobotWare 5.08.

3HAC 027097-001 Revision: -

Safety note

Safety note
Overview Please note that there is no information regarding safety aspects in this manual! In an effort to keep this manual short, there is no information regarding: safe handling and operation of the equipment generic reference information detailed procedures

This information can be found in the Product manuals or the Operating manuals delivered with the robot system.

3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

1 Procedures
1.1. Procedure for single robot systems

1 Procedures
1.1. Procedure for single robot systems
Overview This instruction is valid for IRC5 single robot systems. A single robot system contains either a Single Cabinet Controller (controller with integrated Control Module and Drive Module) or a Dual Controller (Control Module to which one Drive Module is connected). How to get started This procedure details how to get started with a single robot system. Action
1. Mechanically install the robot and controller, and connect the electrical power and signal cables between them. Also connect the electrical power supply.

Info/illustration
These procedures are detailed in the Product Manuals of robot and controller respectively.

2. Make sure all safety related connections are made Refer to the work station wiring correctly. diagram. 3. Connect the FlexPendant to the controller.

Copyright 2007 ABB. All rights reserved.

xx0500001854

A: FlexPendant connector, Single Cabinet Controller 4. If the robot system is delivered with fully functional system software installed, you can proceed as detailed in section How to switch on power in Common procedures for all systems on page 11. If no functional system software has been installed, please proceed as detailed in section Common procedures for all systems on page 11.

3HAC 027097-001 Revision: -

1 Procedures
1.2. Procedure for MultiMove systems

1.2. Procedure for MultiMove systems

Overview This instruction is valid for IRC5 multi robot systems, i.e. systems using the MultiMove option.

xx0400001042

A MultiMove robot system contains either a Single Cabinet Controller (an integrated Control Module and Drive Module as shown in the illustration above) or a separate Control Module to which a number of Drive Modules (one for each robot being run by the system) have been connected. Up to four robots may be operated by a MultiMove system. NOTE! All multi robot systems are configured as single robot systems on delivery. In order to be fully functional as multi robot systems, these systems must be re-configured. How to perform this is detailed in Operating manual - RobotStudio Online.

Continues on next page

8 3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

1 Procedures
1.2. Procedure for MultiMove systems Continued How to get started This procedure details how to get started with a multi robot system. Action Info/illustration

1. Mechanically install the robot and These procedures are detailed in the controller, and connect the electrical power Product Manuals of robot and controller and signal cables between them. Also respectively. connect the electrical power supply. 2. Connect the Ethernet cables from each Drive Module to the Control Module Ethernet card. Make sure the Drive Modules are connected in the correct order! The order must correspond to the order in which the key strings are entered when creating the system.

xx0400001141

Copyright 2007 ABB. All rights reserved.

Connections: A: Robot communication card B: Ethernet card C: Ethernet connection to Drive Module #1 (connected on delivery) D: Ethernet connection to Drive Module #2 E: Ethernet connection to Drive Module #3 F: Ethernet connection to Drive Module #4

Continues on next page

3HAC 027097-001 Revision: 9

1 Procedures
1.2. Procedure for MultiMove systems Continued Action
3. Before connecting the safety signal cables, remove jumpers from connectors X7, X8, X14 and X17 as required by the number of Drive Modules to connect. Connect the safety signal cables from each Drive Module to the Control Module panel board as shown in the figure.

Info/illustration

xx0400001295

Connections: X7: safety signal cable to Drive Module #1(connected on delivery) X8: safety signal cable to Drive Module #2 X14: safety signal cable to Drive Module #3 X17: safety signal cable to Drive Module #4 4. Make sure all safety related connections are made correctly. 5. Connect the FlexPendant to the controller. Refer to the work station wiring diagram.

xx0500001854

A: FlexPendant connector, Single Cabinet Controller 6. Proceed as detailed in section Common procedures for all systems on page 11.

10

3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

1 Procedures
1.3. Common procedures for all systems

1.3. Common procedures for all systems

Overview These procedures are common for installing all robot systems. How to install RobotStudio Online on a PC Action
1. Insert the Robot's software CD in the PC. If a menu for the CD is opened automatically, continue with step 5. If no menu for the CD is opened, continue with step 2. 2. On the Start menu, click Run. 3. In the Open box, type the drive letter for your CD drive followed by: :\launch.exe Example: If your CD drive has the letter D, then type: D:\launch.exe 4. Click OK. 5. Select language for the CD menu. 6. On the CD menu, click Install. 7. On the installation menu, click RobotStudio Online. This opens the Installation wizard, which will guide you through the rest of the software installation. 8. Follow the instructions in the Installation wizard. 9. After installing RobotStudio Online, proceed with obtaining a RobotStudio Online license key if required. NOTE that for a try-out period of 30 days, RobotStudio Online will work without license key.

How to obtain a RobotStudio Online licence key It is not vital to perform this step at this point, but after the 30 day demo period has expired, you need to request a license key for each installation on a PC. Action
Copyright 2007 ABB. All rights reserved.

Info

1. On the Start menu, point to Programs, ABB Industrial IT, Robotics IT, Licensing and then click License Key Request Wizard. 2. Follow the instructions in the wizard and enter the requested information. When the wizard is completed, a license key request file is saved on your PC. 3. Attach the license key request file to an e-mail and send it to [email protected]. A license key file will then be sent by e-mail to the email address specified in the License key request wizard within a few minutes. 4. After obtaining a RobotStudio Online license key, proceed with installing it. The file is called LicenseKeyRequestRobotStudio Onlineuniquenumber.txt, and it will be located on the desktop The file must be attached to the email (not copied into the body of the e-mail) and have the extension txt (as it is created), or the license key request will fail processing.

Continues on next page

3HAC 027097-001 Revision: 11

1 Procedures
1.3. Common procedures for all systems Continued How to install the RobotStudio Online licence key Action
1. Detach the license key file from the e-mail and save it to a file on your PC. 2. Double-click the license key file. This will open the License install wizard. 3. Follow the instructions in the Licence install wizard. 4. After installing the RobotStudio Online license key, proceed with configuring and connecting a PC to the controller.

How to configure and connect a PC or network to the controller The illustration below shows the two main ports on the controller's Computer Unit: the Service Port and the LAN port. Make sure the LAN (factory network) is not connected to any of the service ports!

xx0700000003

A B

Service port on computer unit (connected to Service port on the Control Module front through a cable) LAN port on computer unit (connects to factory LAN)

Action
1. Make sure the network setting on the PC to be connected is correct.

Info
Refer to the system documentation for your PC, depending on the operating system you are running. The PC must be set to "Obtain an IP address automatically". The cable is delivered in the RobotWare product box. The service port is shown in the figure above.

2. Use the delivered category 5 Ethernet crossover boot cable with RJ45 connectors. 3. Connect the crossover boot cable to the network port of your PC. 4. Connect the other end of the crossover boot cable to the service port. 5. After configuring and connecting a PC to the controller, proceed with creating a system if required. NOTE that normally this step will not be required, since a system has already been installed.

Continues on next page

12 3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

1 Procedures
1.3. Common procedures for all systems Continued How to create a system using RobotStudio Online Normally, no system will have to be created for single robot systems since one is already installed on delivery. However, if your system uses the option MultiMove, you must create a new system defining all robots in the system. If for some reason the delivered system does not work, a new system must be created and loaded as outlined below. A detailed procedure is given in Operating manual - RobotStudio Online. For MultiMove systems, more information is also described in Application manual - MultiMove. Action
1. Start RobotStudio Online on the PC and go to the menu Tools and then System Builder. 2. Before creating a new system, make sure the following criteria are met: The RobotWare media pool must be installed on your PC. You must have a RobotWare key for the system, if the system is to run on a controller. 3. Click Create New. A wizard for creating new systems is started. 4. Follow the steps in the wizard: Enter name and location Enter RobotWare key(s) Add additional options Modify options Add configuration files Add files to home directory View summary Finish 5. After creating a system, proceed with switching on the power.
Copyright 2007 ABB. All rights reserved.

Info

The RobotWare key is a license key that determines which robot model(s) to use and which RobotWare options to run on the controller. It is delivered on the software CD (delivered with the robot).

Some of the steps are optional and can be skipped.

Continues on next page

3HAC 027097-001 Revision: 13

1 Procedures
1.3. Common procedures for all systems Continued How to switch on power The mains power switch(es) is located on the front of the controller/modules. See illustration of the switch below.

en0400000793

Action
1. Switch on the power to the Drive Module(s).

Info
If you have a single robot system with a Single Cabinet Controller, proceed to step 2. The system will now start up, which will take a couple of minutes. The system will be ready to operate when the FlexPendant displays the start window. If the system does not start up, or if the start window is not displayed, please proceed as detailed in Operating manual Trouble shooting.

2. Switch on the power to the Control Module.

3. After switching the power on, proceed with loading calibration data.

How to load calibration data The calibration data is normally stored on the serial measurement board of each robot, regardless of whether the robot runs an absolute measurement system (Absolute Accuracy option is installed, AbsAcc) or not. This data is normally transferred automatically to the controller when the system is powered up, and in such cases no action is required by the operator.
Copyright 2007 ABB. All rights reserved.

Verify that the correct SMB data has been loaded into the system as detailed below. In a MultiMove system, this procedure must be repeated for each robot. Action
1. On the FlexPendant, tap the ABB menu, then tap Calibration and select a mechanical unit. 2. Tap SMB memory and then tap Show status. The data is displayed with status on the SMB and on the controller. 3. If Valid is displayed under the headings Cabinet Memory and SMB memory, calibration data is correct. If not, the data (on the SMB board or in the controller) must be replaced with the correct one as detailed below: If, for instance, the SMB board has been replaced, transfer data from controller to SMB board.If the controller has been replaced, transfer data from the SMB board to the controller. Transfer data by tapping SMB Memory, Update... and then selecting which data to update. 4. After loading calibration data, proceed with updating the revolution counters.

Continues on next page

14 3HAC 027097-001 Revision: -

1 Procedures
1.3. Common procedures for all systems Continued How to update revolution counters In a MultiMove system, this procedure must be repeated for each robot. Action
1. Manually run the robot, using the joystick on the FlexPendant, to a position close to the calibration position. 2. After positioning all axes within the scale indicated by the calibration marks, store the revolution counter settings. On the FlexPendant, tap the ABB menu, then tap Calibration. Select the mechanical unit to be calibrated. Tap Update revolution counters and follow the instructions provided.

Info
The calibration position of each axis is indicated by the calibration marks. Caution! If a revolution counter is incorrectly updated, it will cause incorrect robot positioning, which in turn may cause damage or injury! Check the calibration position very carefully after each update.

Copyright 2007 ABB. All rights reserved.

3HAC 027097-001 Revision: -

15

1 Procedures
1.3. Common procedures for all systems

16

3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

2 General
2.1. What you need to get the system started

2 General
2.1. What you need to get the system started
Illustration The illustration depicts, in a schematic way, the delivered parts, the software tools to install them and the basic work flow.

en0400000766

Copyright 2007 ABB. All rights reserved.

Parts Part
A

Description
Manipulator (a generic model shown)

Described in:
Documents specified in section Product documentation, M2004 on page 31. Documents specified in section Product documentation, M2004 on page 31.

B1

Control Module, IRC5, containing the control electronics of the robot system.

B2

Drive Module, IRC5, containing the power electronics Documents specified in of the robot system. section Product documentation, M2004 on page 31. In a Single Cabinet Controller the Drive Module is included in the single cabinet. In a MultiMove system, there is more than one Drive Module.

Continues on next page

3HAC 027097-001 Revision: 17

2 General
2.1. What you need to get the system started Continued Part Description
C RobotWare CD containing all robot software specified in section What is RobotWare? on page 26What is RobotWare? on page 26. Documentation CD. Containing documentation files as specified in section Product documentation, M2004 on page 31. Documents specified in section Product documentation, M2004 on page 31. Documents specified in section Product documentation, M2004 on page 31, and in section What is RobotStudio Online? on page 25.

Described in:

Robot system software being run by the robot controller. The system has been loaded into the controller from the server on the local area network. RobotStudio Online PC software installed on PC x. RobotStudio Online is used for loading the RobotWare software to the server as well as configuring the robot system and then loading the complete robot system into the robot controller. RobotStudio Online is used to perform tasks as defined in section When to use the FlexPendant and RobotStudio Online on page 28. Calibration data diskette for systems running the Absolute Accuracy option only. Calibration data for systems without this option is normally delivered on the Serial Measurement Board (SMB).

FlexPendant, which is connected to the controller, is Documents specified in used to perform tasks as defined in section When to section Product documentause the FlexPendant and RobotStudio Online on page tion, M2004 on page 31. 28. Server on network (not included in the delivery). This may be used for manually storing: RobotWare complete robot systems documentation files In this context, the server may be considered as a storage unit used by the PC x, and may even be the same unit! The server may be disconnected when not transferring data between the server and controller!

PC K The server may be used for: all RobotWare software may be manually stored using the PC and RobotStudio Online. complete configured system files may be manually stored after being created using the portable PC. all robot documentation files may be manually stored after being installed using the portable PC and RobotStudio Online. In this context, the server may be considered as a storage unit used by the portable PC.

Continues on next page

18 3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

2 General
2.1. What you need to get the system started Continued Part
M

Description
RobotWare license key. The original key string is printed on a paper (for the Dual Controller there is one key for the Control Module and one for the Drive Module, and in a MultiMove system there is one key for each module) delivered inside the Drive Module. If ordered, the RobotWare license key is installed on delivery, so no further actions are required to get the system running. Serial Measurement Board (SMB) handling resolver data and storing calibration data. For systems not running the Absolute Accuracy option, the calibration data is stored on the SMB on delivery. PC (not included in the delivery), may even be the same unit as the server J, shown above! The PC may be disconnected when not transferring data between the server and controller!

Described in:

PC x

Copyright 2007 ABB. All rights reserved.

3HAC 027097-001 Revision: -

19

2 General
2.2. What is a FlexPendant?

2.2. What is a FlexPendant?

Overview The FlexPendant (occasionally called TPU or teach pendant unit) is a hand held operator unit used to perform many of the tasks involved when operating a robot system: running programs, jogging the manipulator, modifying robot programs etcetera. NOTE! Note that a few specific functions, such as administer the user authority system (UAS), cannot be performed using the FlexPendant, but only by using RobotStudio Online. Use Operating manual - RobotStudio Online for details in these cases. Complete computer and integral part of IRC5 The FlexPendant consists of both hardware and software and is a complete computer in itself. It is an integral part of IRC5, connected to the controller by an integrated cable and connector. The hot plug button option, however, makes it possible to disconnect the FlexPendant in automatic mode and continue running without it. See Using the hot plug in Operating manual - IRC5 with FlexPendant for details about this. Main parts The FlexPendant is designed for continuous operation in harsh industrial environment. Its touch screen is easy to clean and resistant to water, oil and accidental welding splashes. These are the main parts of the FlexPendant.

en0300000586

A B C D E

Connector Touch screen Emergency stop button Enabling device Joystick

Continues on next page

20 3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

2 General
2.2. What is a FlexPendant? Continued Hard buttons There are eight dedicated hardware buttons on the FlexPendant, four of which the function is assigned by the end user.

en0300000587

A-D E F G H

Programmable keys, 1 - 4. How to define their respective function is detailed in section Programmable keys in Operating manual - IRC5 with FlexPendant. START button. Starts program execution. Step BACKWARD button. Executes one instruction backward as button is pressed. Step FORWARD button. Executes one instruction forward as button is pressed. STOP button. Stops program execution.

Copyright 2007 ABB. All rights reserved.

Continues on next page

3HAC 027097-001 Revision: 21

2 General
2.2. What is a FlexPendant? Continued How to hold the FlexPendant The FlexPendant is typically operated while being held in the hand. A right-handed person uses his left hand to support the device while the other hand performs operations on the touch screen. A left-hander, however, can easily rotate the display through 180 degrees and use his right hand to support the device. See Adapting the FlexPendant to left-handedness in Operating manual - IRC5 with FlexPendant for further information.

en0400000913

Operated in fourteen languages

Copyright 2007 ABB. All rights reserved.

As suggested by its name, the FlexPendant is designed with flexibility and adaptation to endusers specific needs in mind. Currently, it can be operated in 14 different languages, including Asian character-based languages such as Chinese and Japanese. The individual FlexPendant supports up to three languages, selected before the installation of the system to the robot controller. Switching from one of the installed languages to another is easy. See Changing language in Operating manual - IRC5 with FlexPendant for information about how to do it.

Continues on next page

22 3HAC 027097-001 Revision: -

2 General
2.2. What is a FlexPendant? Continued Touch screen elements The illustration shows important elements of the FlexPendant touch screen.

en0300000588

A B C D E F
Copyright 2007 ABB. All rights reserved.

ABB menu Operator window Status bar Close button Task bar Quickset menu

Continues on next page

3HAC 027097-001 Revision: 23

2 General
2.2. What is a FlexPendant? Continued ABB menu From the ABB menu the following items can be selected HotEdit Inputs and Outputs Jogging Production Window Program Editor Program Data Backup and Restore Calibration Control Panel Event Log FlexPendant Explorer System Info etc.

This is further detailed in section The ABB menu in Operating manual - IRC5 with FlexPendant. Operator window The operator window displays messages from robot programs. This usually happens when the program needs some kind of operator response in order to continue. This is described in section Operator window in Operating manual - IRC5 with FlexPendant. Status bar The status bar displays important information about system status, such as operating mode, motors on/off, program state and so on. This is described in section Status bar in Operating manual - IRC5 with FlexPendant. Close button Tapping the close button closes the presently active view or application. Task bar You can open several views from the ABB menu, but only work with one at a time. The task bar displays all open views and is used to switch between these. Quickset menu The quickset menu provides settings for jogging and program execution. This is described in section The Quickset menu in Operating manual - IRC5 with FlexPendant.
Copyright 2007 ABB. All rights reserved.

24

3HAC 027097-001 Revision: -

2 General
2.3. What is RobotStudio Online?

2.3. What is RobotStudio Online?

Overview RobotStudio Online is a PC software with which you work with robots, as a complement to working from the FlexPendant. RobotStudio Online is optimized for text based programming (suitable for programs with lot of logic or complex structure) and tasks related to managing the robot's system. RobotStudio Online can be installed on an ordinary computer running Windows 2000 or later. This computer can then be connected to one or several controllers by an Ethernet network, or to one single controller by the controller's service port connection. RobotStudio Online functionality The main entry to the functionality of RobotStudio Online is a robot view explorer. From this you select which robot to work with, in cases where several robots are installed, and what parts of the system you want to work with. RobotStudio Online contains: The System Builder for creating, installing and maintaining systems. A configuration editor for editing the system parameters of the running system. A program editor for online programming. An event log for monitoring and saving robot events. Tools for backing up and restoring systems. An administration tool for the User Authorization System. A file manager for transferring files between the PC and controllers. A task window for operating all kinds of tasks in the controller. Other tools for viewing and handling controller and system properties.

Copyright 2007 ABB. All rights reserved.

3HAC 027097-001 Revision: -

25

2 General
2.4. What is RobotWare?

2.4. What is RobotWare?

Concept RobotWare is a generic term for all software to be installed in the robot system designed to operate the robot. RobotWare is installed and stored in the Media Pool folder on a PC/server. The media pool is described in section About the media pool on page 27. RobotWare is delivered on a CD and this contains software for all available models, options and such. However, the RobotWare license keys, required to access the software, are delivered as character strings printed on a piece of paper delivered with the controller cabinet. There is one key for the Control Module, and one key for each Drive Module. When adding functionality at a later date, a new controller license key is required to access the functions. The key is available from your local ABB representative.

26

3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

2 General
2.5. About the media pool

2.5. About the media pool

Overview The media pool is a folder on your PC that contains the RobotWare software. It is from the media pool that you select programs and options when building systems. The default media pool If RobotWare is installed with default settings on the PC, the default media pool is located in the C:\Program Files\ABB Industrial IT\Robotics IT folder. Customized media pools You can create customized media pools by creating new folders to which you copy RobotWare files from existing media pools. You can also update or modify a media pool by importing new parts of RobotWare using the Import System Tool in RobotStudio Online. In RobotStudio Online, you then choose which media pool to use when creating new systems.

Copyright 2007 ABB. All rights reserved.

3HAC 027097-001 Revision: -

27

2 General
2.6. When to use the FlexPendant and RobotStudio Online

2.6. When to use the FlexPendant and RobotStudio Online

Overview For operating and managing the robot, you either use the FlexPendant or RobotStudio Online. The FlexPendant is optimized for handling robot motions and ordinary operation, and RobotStudio Online is optimized for configuration, programming and other tasks not related to the daily operation. Start, restart and shut down the controller To...
Start the controller. Restart the controller. Shut down the controller.

Use...
The power switch on the controller's front panel. The FlexPendant, RobotStudio Online or the power switch on the controller's front panel. The power switch on the controller's front panel or the FlexPendant, tap Restart, then Advanced.

Run and control robot programs To...

Jog a robot. Start and stop background tasks

Use...
The FlexPendant RobotStudio Online

Start or stop a robot program. The FlexPendant or RobotStudio Online

Communicate with the controller To...

Acknowledge events. View and save the controller's event logs.

Use...
The FlexPendant. RobotStudio Online or the FlexPendant.

Back up the controller's software to files on the RobotStudio Online or the FlexPendant. PC or a server. Back up the controller's software to files on the The FlexPendant. controller Transfer files between the controller and network drives. RobotStudio Online or the FlexPendant.
Copyright 2007 ABB. All rights reserved.

Continues on next page

28 3HAC 027097-001 Revision: -

2 General
2.6. When to use the FlexPendant and RobotStudio Online Continued Program a robot To...
Create or edit robot programs in a flexible way. This is suitable for complex programs with a lot of logic, I/O signals or action instructions.

Use...
RobotStudio Online to create the program's structure and most of the source code and the FlexPendant to store robot positions and make final adjustments to the program. When programming, RobotStudio Online provides the following advantages: A text editor optimized for RAPID code, with auto-text and tool-tip information about instructions and parameters. Program check with program error marking. Close access to configuration and I/O editing.

Create or edit a robot program The FlexPendant. in a supportive way. This is When programming, the FlexPendant provides the following suitable for programs that advantages: mostly consist of move Instruction pick lists instructions. Program check and debug while writing Possibility to create robot positions while programming Add or edit robot positions. Modify robot positions. The FlexPendant. The FlexPendant.

Configure the robot's system parameters To...

Edit the system parameters of the running system.

Use...
RobotStudio Online or the FlexPendant

Save the robot's system parameters as config- RobotStudio Online or the FlexPendant uration files. Load system parameters from configuration files to the running system. Load calibration data.
Copyright 2007 ABB. All rights reserved.

RobotStudio Online or the FlexPendant RobotStudio Online or the FlexPendant

Create, modify and install systems To...

Create or modify a system. Install a system on a controller.

Use...
RobotStudio Online together with RobotWare and a valid RobotWare Key. RobotStudio Online

Install a system on a controller from The FlexPendant. a USB memory.

Calibration To...
Calibrate base frame etc. Calibrate tools, work objects etc.

Use...
The FlexPendant The FlexPendant

Continues on next page

3HAC 027097-001 Revision: 29

2 General
2.6. When to use the FlexPendant and RobotStudio Online Continued Related information The table below specifies which manuals to read, when performing the various tasks referred to: Recommended use...
FlexPendant RobotStudio Online

for details, see manual...

Operating manual - IRC5 with FlexPendant Operating manual - RobotStudio Online

Document number
3HAC16590-1 3HAC18236-1

30

3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.

2 General
2.7. Product documentation, M2004

2.7. Product documentation, M2004

General The robot documentation may be divided into a number of categories. This listing is based on the type of information contained within the documents, regardless of whether the products are standard or optional. This means that any given delivery of robot products will not contain all documents listed, only the ones pertaining to the equipment delivered. However, all documents listed may be ordered from ABB. The documents listed are valid for M2004 robot systems. Product manuals All hardware, robots and controllers, will be delivered with a Product manual which is divided into two parts: Product manual, procedures Safety information Installation and commissioning (descriptions of mechanical installation, electrical connections) Maintenance (descriptions of all required preventive maintenance procedures including intervals) Repair (descriptions of all recommended repair procedures including spare parts) Additional procedures, if any (calibration, decommissioning)

Product manual, reference information Reference information (article numbers for documentation referred to in Product manual, procedures, lists of tools, safety standards) Part list Foldouts or exploded views Circuit diagrams

Copyright 2007 ABB. All rights reserved.

The product manual published as a PDF consists of only one file where the two parts are presented together, as one Product manual. Technical reference manuals The following manuals describe the robot software in general and contain relevant reference information: RAPID Overview: An overview of the RAPID programming language. RAPID Instructions, Functions and Data types: Description and syntax for all RAPID instructions, functions and data types. System parameters: Description of system parameters and configuration workflows.

Continues on next page

3HAC 027097-001 Revision: 31

2 General
2.7. Product documentation, M2004 Continued Application manuals Specific applications (e.g. software or hardware options) are described in Application manuals. An application manual can describe one or several applications. An application manual generally contains information about: Operating manuals This group of manuals is aimed at those having first hand operational contact with the robot, i.e. production cell operators, programmers and trouble shooters. The group of manuals includes: Getting started - IRC5 and RobotStudio Online IRC5 with FlexPendant RobotStudio Online Trouble shooting - IRC5 for the controller and robot The purpose of the application (what it does and when it is useful) What is included (e.g. cables, I/O boards, RAPID instructions, system parameters, CD with PC software) How to use the application Examples of how to use the application

32

3HAC 027097-001 Revision: -

Copyright 2007 ABB. All rights reserved.