User Manual For Video Vehicle Detector

Sinowatcher Technology Co.
, Ltd
Best solutions to guarantee traffic safety
Integrated Video Vehicle Detector

System
FEATURES & BENEFITS
Ø Extensively used in Traffic Management Systems.
Ø IVD Integrated video vehicle detector integrates
high-definition (HD) camera and vehicle detection
together to achieve high quality video vehicle detection function.
Ø Ethernet Port, Rs-485 and interface I/O outputs.
Ø Real-time HD output H.264.
Ø Built in flash memory for 1 year (1 data per minute.)
Ø SD external storage up to 32 GB (1 GB = 4 years.)
Ø High enclosure protection IP67.
Ø 5.0 Mpx sensor (16 times of better quality than traditional VGA cameras.)
Ø Web server embedded for using IE browser to log in, implement remote parameter
configuration and monitoring the device status.
Ø Functions as speed detection, traffic flow, Vehicles length, occupancy.
Ø Degree of accuracy: 95% Traffic flow, 85% Speed, 99% Queue long and +/- 1m Vehicle
length.
Ø Application in Semi actuated, Self-actuated and adaptive traffic control modes.
Ø More than 50 000 working hours.
Ø Working humidity range: up to 95% non-condensing
Ø Working temperature: -40 C° to +80 C°.
Sinowatcher Technology Co., Ltd.
Please visit our website www.trafficsolution.cn

Specifications subject to change without notice
Sinowatcher Technology Co., Ltd
TECHNICAL DATA
Characteristics Range Details
Voltage 12V@3amp DC power supply
I/O Interface card for outputs

RS-232 Serial debugging port
Ports
RS-485 Serial communication for outputs
RJ-45 Video streaming / remote config. and control.
Traffic flow 95%

Queue 99%
Main Functions
Speed Measure 85%
Length +/- 1meter
Lanes of control Up to 4 Independent virtual loops

Resistance against dust and
IP67 IEC 60529
water
Data Storage Up to 32GB SD card Slot , 1GB saves 4 years of Data *
Statistical period 30-3600s 0.5 minutes to 1hours configurable intervals
Lightning protection and

EMC
anti-interference
Working temperature -40 C to +80C
Working life time More than 50 000
Working Humidity 95%, no condensing
Warranty 2 years
FUNCTIONS
Vehicle Detection Function
Ø Vehicle presence detection
Ø Vehicle Instantaneous speed
Ø Vehicle length detection
Ø Vehicle queue length detection
The VD detects real-time queue length and gives an over-length alarm to Signal Controller.
Email. [email protected]
Tel. 86-755-29407296 * Fax. 86-755-29440797

Shajing, Bao’an, Shenzhen, 518104, P.R. China.
Statistics Function
Ø Traffic volume/flow
The number of motor vehicles passing through a certain section of the road in a specified time period.
Ø Headway
The time interval between the head of two consecutive vehicles passing through a certain same section
in a queue of vehicles traveling on the same lane. The unit is seconds.
Ø Spatial Headway
The distance between the head of front and followed vehicles in the same lane. The unit is meter.
Ø Time occupancy
On a certain road section, the ratio of the cumulative value of vehicle passing time to the observation
time, expressed as a percentage.
Real-time HD Video Output

Ø Real-time high-definition output video data in H.264 compression format for easy viewing.
Real-time Data Output

Ø Overlay output on the image
Watch the detection result through the real-time video stream.
Ø RS485 interface output (protocol communication)
Real-time detection data shared through RS485 interface to other equipment like traffic signal controller:
vehicle presence, speed, length, queue length, etc.
Ø Switch value output (I/O signal)
Vehicle presence, queue over-length alarming
Ø Network interface output (protocol communication)
Real-time detection data shared through RJ45 interface(TCP/UDP) to other equipment like traffic signal
controller: vehicle presence, speed, length, queue length, etc.
Statistical Data Storage and Output

Ø Stored in the built-in FLASH, 1-year storage if 1 detection data/min.
Ø Stored in SD card (maximum 32G), storage time depending on SD card capacity, normally 1G enough
for 4 years’ storage.

Embedded WEB Server

Ø The device is embedded with a WEB server, and you can log in with an IE browser to realize
remote parameter configuration and device status monitoring.
Automatic Maintenance Function

Ø Self-checking on equipment real-time operating state
Ø Automatic fault alarm function
Built-in log information to show equipment fault information.
APPLICATION SCENARIOS
Road Traffic Flow Collection

Video vehicle detector are widely used in urban roads, highway, bridge, etc. places to collect
multi-type traffic data including: traffic flow, average vehicle driving speed, average vehicle
length, average vehicle headway, average vehicle spatial headway, traffic occupancy, etc.
Tel. 86-755-29407296 * Fax. 86-755-29440797

Adaptive Traffic Signal Control in Junctions

Traffic signal controller can achieve adaptive traffic signal control with the real-time traffic data
collected by video vehicle detector, including vehicle presence, over-length alarming signal, etc.

INTERFACE BOARD
SIDE 1
SIDE 2
Tel. 86-755-29407296 * Fax. 86-755-29440797

WIRING DETAILS
There are two Communication ways between Video Vehicle Detector and Traffic Signal Controller:
1. Through protocol communication, RS485/RJ45 interface directly.
(Multi data types like presence, flow, speed, headway, etc.)
2. Through I/O interface, in which situation there shall be an interface board to transform RS485 or
TCP/IP data from video vehicle detector to I/O signal to signal controller.
# Switching value Signal – connect I/O interface only
# High low-level output – connect I/O interface + power adaptor B with PULL interface.
Wiring of Video Vehicle Detector
RS232 Port name Details

DC GND
RS485 POWER
DC +12V
“+” RS485 A
RS485
DC12V input “-” RS485 B
“1” Sending
“2” Receiving
RS232
“3” GND
RJ45 RJ45 Ethernet cable
Basically only need to connect DC12V input and RJ45 interface.

RS485/232 for other special communication use.
1. Connect power adaptor with video detector.
2. Connect RJ45 interface with a network switch through network cable.

Wiring of Interface Board

1. Connect power adaptor with it as picture below.
2. # Switching value Signal – connect I/O outputs interface with signal controller inputs only.
# High low-level voltage output – connect I/O interface with signal controller + power adaptor B
with PULL interface.
Tel. 86-755-29407296 * Fax. 86-755-29440797

System Wiring Diagram
Power
Adaptor A
DC12V Power
Adaptor A
Video
Detector 1 DC12V
Power
Adaptor A
Interface
DC12V Video Board Power
Detector 2 Adaptor B
DC5V
VD 3 RJ45 I/O
…
PC for Network Traffic
Program Switch Controller
Electric cable
Network cable
Note: DC5V power adaptor B is not a must to connect, only when there is no power in signal controller
inputs circuits design and when need high low-level voltage outputs signal from Interface Board.
If just normal switching value signal, no need to use DC5V Power Adaptor B.
Installation Instruction
Packing List
Part 1:
# 1pcs Video Vehicle Detector
# 2pcs short screws for fixing video detector on the support (used only when using thinner support)

Part 2:
# DC12V power adaptors for video vehicle detector, 1pcs for each detector.
Part 3:
# 1pcs Interface Board
# 1pcs DC12V power adaptor A
# 1pcs DC5V power adaptor B
Tel. 86-755-29407296 * Fax. 86-755-29440797

Part 4:
# 1set bracket + long tube support
# 3pcs screws coming from the same bag:
1pcs longer for tighten the long tube support and top bracket;
2pcs shorter for fixing video detector on the bracket.
Part 5:
# Stainless steel waterproof casing to hold DC12 power adaptor for video detector.
# Screw accessories (2pcs with white head to fix casing cover, the other 2pcs for spare use).
# Stainless steel clamp for above casing.

Part 6:
Stainless steel clamps, 2pcs for each casing above
Installation
Step 1:
Twist the long tube support until see another screw hole, then use the longer screw to fix it, thus the top
bracket and long support tightened.
Tel. 86-755-29407296 * Fax. 86-755-29440797

Step 2:
Fix video detector on the top bracket with 2 screws.
Step 3:
Fix the waterproof casing with stainless steel clamps onto the long tube support.
Do not block the tube support screw fixing location

Step 4:
Open the waterproof casing:
# Put DC12V power adaptor inside.
# Connect power output joint with video detector power input.
# Connect network cable with RJ45 interface.
# Cut the power adaptor plug and connect it with 220VAC input grid power cable,
then protect the joint with high-voltage waterproof tape.
Tel. 86-755-29407296 * Fax. 86-755-29440797

Step 5:
Put the cover back and fix it with 2 screws at two sides.

Step 6:
Fix the long tube base with CARDAN bracket (2 layer or 3 layers) as below.
Front-back adjustment only

OR All angle adjustment
Step 7:
Fix the CARDAN bracket on pole with stainless steel clamps (at least 2).
Tel. 86-755-29407296 * Fax. 86-755-29440797

Attention：
Adjust the viewing angle of the video vehicle detector acc. to the real-time video displaying in PC, so
that all detected lanes and vehicles driving in those lanes can be covered in the video as well as the
corresponding virtual loops.


User Manual For Video Vehicle Detector

Uploaded by

Copyright:

Available Formats

User Manual For Video Vehicle Detector

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

User Manual For Video Vehicle Detector

Uploaded by

Copyright:

Available Formats

Sinowatcher Technology Co.

Integrated Video Vehicle Detector

FEATURES & BENEFITS

Ø Extensively used in Traffic Management Systems.

Ø IVD Integrated video vehicle detector integrates

high-definition (HD) camera and vehicle detection

together to achieve high quality video vehicle detection function.

Ø Ethernet Port, Rs-485 and interface I/O outputs.

Ø Real-time HD output H.264.

Ø Built in flash memory for 1 year (1 data per minute.)

Ø SD external storage up to 32 GB (1 GB = 4 years.)

Ø High enclosure protection IP67.

configuration and monitoring the device status.

Ø Functions as speed detection, traffic flow, Vehicles length, occupancy.

Ø Application in Semi actuated, Self-actuated and adaptive traffic control modes.

Ø More than 50 000 working hours.

Ø Working humidity range: up to 95% non-condensing

Ø Working temperature: -40 C° to +80 C°.

Sinowatcher Technology Co., Ltd.

Please visit our website www.trafficsolution.cn

Characteristics Range Details

Voltage 12V@3amp DC power supply

I/O Interface card for outputs

Traffic flow 95%

Lanes of control Up to 4 Independent virtual loops

Statistical period 30-3600s 0.5 minutes to 1hours configurable intervals

Lightning protection and

Working temperature -40 C to +80C

Working life time More than 50 000

Working Humidity 95%, no condensing

Vehicle Detection Function

Ø Vehicle presence detection

Ø Vehicle Instantaneous speed

Ø Vehicle length detection

Ø Vehicle queue length detection

Tel. 86-755-29407296 * Fax. 86-755-29440797

Real-time HD Video Output

Real-time Data Output

controller: vehicle presence, speed, length, queue length, etc.

Statistical Data Storage and Output

Sinowatcher Technology Co., Ltd.

Please visit our website www.trafficsolution.cn

Embedded WEB Server

Automatic Maintenance Function

Road Traffic Flow Collection

Tel. 86-755-29407296 * Fax. 86-755-29440797

Adaptive Traffic Signal Control in Junctions

Sinowatcher Technology Co., Ltd.

Please visit our website www.trafficsolution.cn

Tel. 86-755-29407296 * Fax. 86-755-29440797

Wiring of Video Vehicle Detector

RS232 Port name Details

Basically only need to connect DC12V input and RJ45 interface.

1. Connect power adaptor with video detector.

2. Connect RJ45 interface with a network switch through network cable.

Sinowatcher Technology Co., Ltd.

Please visit our website www.trafficsolution.cn

Wiring of Interface Board

Tel. 86-755-29407296 * Fax. 86-755-29440797