BULLETIN

NMce-2017

ISO 9001

CERTIFIED

NAMUR DIRECT MOUNT PNEUMATIC ACTUATOR VALVES

Versa Product Company, Inc., 22 Spring Valley Rd., Paramus, NJ 07652 USA Phone: (201) 843-2400 Fax: (201) 843-2931
Versa BV, Prins Willem Alexanderlaan 1427, 7312 GB Apeldoorn, The Netherlands Phone: +31-55-368-1900 Fax: +31-55-368-1909
E-mail: [email protected] www.versa-valves.com
DIRECT MOUNT ACTUATOR VALVES
GENERAL DESCRIPTION
The Versa NAMUR mount control valves are high flow, bubbletight, direct acting or solenoid/pilot operated. They are designed
to mount directly to any NAMUR actuator, thus reducing actuator response time and cost of tubing, fittings, brackets, and labor.
These valves are available in two materials - Aluminum and 316L stainless steel.
E5 is a direct acting 3-way (3/2) solenoid valve. C5 and C316 are solenoid/pilot operated high flow, 5-port NAMUR valves. They
are available as single or double solenoid 2-position (C5 - C316) and 3-position (C5) models. Single solenoid spring return
models utilize an air assisted spring return feature, assuring a positive return. Double solenoid valves may be used in applications
where a momentary signal is required or in a “fail in last shifted position” actuator application.
A complete selection of electrical connections, area classifications, and power requirements makes the most exacting and
demanding specifications or applications easy to satisfy.

E5 NAMUR C5 NAMUR C316 NAMUR

General Description General Description General Description

The aluminum E5 NAMUR mount The aluminum C5 NAMUR is available as The C316 NAMUR valve is available
either 4-way (for double acting actuators) as either a 4-way (for double acting
control valve is an inexpensive, actuators) or as a 3-way (for spring return
or 3-way (for spring return or fail-safe
simple and effective 3-way direct- actuators). This valve is field convertible actuators).
acting solenoid valve. It is designed utilizing no special tools, gaskets, or
to mount directly to any actuator with When the 3-way function is utilized,
sealants. the unused exhaust port becomes an
NAMUR footprint thus reducing cost actuator vent where a filter/muffler can
of tubing, fittings, brackets and labor. Relocation of a port plug converts a
3-way to a 4-way, or a 4-way to a 3-way. be installed to prevent contaminants from
It is most effective on spring return or When the 4-way valve is converted to entering the valve or the actuator.
fail-safe actuators where high speed 3-way function, the unused exhaust port The 5-port design allows the user to
open or close is not important, but becomes an actuator vent into which a independently control actuator speed in
filter/muffler can be installed to prevent either open or closed direction by utilizing
where cost is a factor. A threaded ac- contaminants from entering either the
tuator vent port is standard. speed or bleed controls.
valve or the actuator.
Available as a 3-way, 2-position, direct Single solenoid models (for 2-position Double solenoid models are equipped
acting solenoid, spring return only, and control), or double solenoid models (for 2 with a detent that maintains the valve
with most of the Versa solenoid options. or 3-position control) are available. in the last shifted position, even in high
vibration applications.
Actuator positioning is possible with the
use of 3-position valves since all Versa
C5 NAMUR valves are bubbletight.
SPECIFICATIONS
Materials PortSize
Valve Body: E5, C5 Anodized aluminum 1/4 NPT or G1/4-Series (vent
E5
C316 316L Stainless Steel Inlet and 10-32)
Plunger: C5 Anodized aluminum exhaust 1/4 NPT or G1/4-Series (C5
C316: 316L Stainless Steel C5/C316 only)
Actuating C5 Solenoid – anodized aluminum. Spring cap – synthetic resin.
Caps: C316 Solenoid and spring cap – 316L Stainless Steel
Flow Rates Cv (average for all ports)
Pilot Piston: C5 Synthetic resin
C316 316L Stainless Steel E5 0.08
Inlet and
C5 0.75
Valve Seals: C5 - C316: Plunger and body – FKM (fluorocarbon) exhaust
C5: Pilot piston – NBR (nitrile) C316 1.6
E5 – C5 Mounting O rings valve/actuator – NBR (nitrile)
C316 Mounting O rings valve/actuator – FKM (fluorocarbon)
Installation and Filtration
Body and C5 - C316 Stainless steel
Screws: E5 Stainless steel (valve to actuator) Valves: No limitations on mounting orientation.
C316 Stainless steel (valve to actuator) Filtration: 40 to 50 micron
C5 Carbon steel (valve to actuator)
Solenoid E5, C5 & C316 Sleeve, plunger & spring – 304 & 430F stainless steel
Parts: E5, C5 Coils – epoxy molded with 3 spade terminals (std). Options
E5, C5 & C316 Coil housing (per coil option selected) see page 26-29 See Options pages 4 and 5

Valve Type Operating Pressure Range* Pneumatic

E5 C5 C316
Single Solenoid/Spring Return (2-position) 0-150 psi (0-10.3 bar) 15-115 psi (1-8 bar) 25-150 psi (1.8-10.3 bar)
Double Solenoid/Detented (2-position) — 10-115 psi (0.7-8 bar) 15-150 psi (1-10.3 bar)
Double Solenoid/Spring Centered (3-position) — 15-115 psi (1-8 bar) —
* Pressures ranges may change based on solenoid option. For applications above 125 psi (8.6 bar) exhaust flow controls or mufflers are recommended.

2 www.versa-valves.com
DIRECT MOUNT ACTUATOR VALVES
VALVE PRODUCT NUMBER SELECTOR

C5, C-316 & E5 NAMUR Basic Valve Number*

SERIES FUNCTION** PORT SINGLE SOLENOID/SPRING RETURN, DOUBLE SOLENOID/ DOUBLE SOLENOID/SPRING CENTERED, 3 POSITION
SIZE Cv 2 POSITION DETENT, 2 POSITION Blocked Center Exhaust Ports Open
CGS-4232-NB1-†-(coil code) CGG-4232-NB1-†-(coil code) CXX-4233-NB1-†-(coil code) CXX-4234-NB1-†-(coil code)
4-way 1/4 NPT .75 CGS-4292-NB1-†-(coil code) CGG-4292-NB1-†-(coil code) CXX-4293-NB1-†-(coil code) CXX-4294-NB1-†-(coil code)
5/2 & 5/3 G1/4 .75
C5 CGS-3232-NB1-†-(coil code) CGG-3232-NB1-†-(coil code) CXX-3233-NB1-†-(coil code) CXX-3234-NB1-†-(coil code)
3-way** CGS-3292-NB1-†-(coil code) CGG-3292-NB1-†-(coil code) CXX-3293-NB1-†-(coil code) CXX-3294-NB1-†-(coil code)
1/4 NPT .75
G1/4 .75
3/2 & 3/3
4-way CGS-4332-316-NE1-†-(coil code) CGG-4332-316-NE1-†-(coil code)
1/4 NPT 1.6
5/2 &
C316 CGS-3331-316-NE1-†-(coil code) CGG-3331-316 NE1-†-(coil code)
3-way
1.6
A

1/4 NPT
3/2 IN EX

E5SM-3011-34-NB1-†-(coil code)
3-Way 1/4 NPT * All valves include O ring interface seals and #10-24 mounting screws. E5 & C5: For #10-32 screws
E5 .08 change NB1 to NB2. For M5 screws change NB1 to NB3. C316 NUMAR: For #10-32 screws change
3/2 NE1 to NE2. For M5 screws change NE1 to NE3.
**3-way is the same body configuration as the 4-way, but has the cylinder port plug in the 3-way
position. See "Note" in C5 section below for description.
† Add suffix option here if required, For coil code see page 4.

DIMENSIONS Series C5 Series E5

TOP VIEW BOTTOM VIEW
1/4” NPT
LOCATING HOLE
MANUAL OVERRIDE (G1/4)
.125 DEEP(3.2)
(Push-Type)
4 3

B
END VIEW 1/4” NPT (G1/4)
B A C TOP VIEW VENT PORT

SIDE VIEW (CGS) NOTE: C 50 VENT

The function of the valve is field convertible.

When ordering a 4 way, CGS-4232-NB1 B
C the plug is in position “4” (as shown).
When ordering a 3-way, CGS-3232-NB1
the plug is in position “3.”
1/4” NPT (G1/4) Exhaust “B” becomes a vent when used 1/4” NPT (G1/4) A
A as a 3-way. INLET PORT

SIDE VIEW (CGG/CXX)

1/4” NPT (G1/4)

A

Series C316
Typical CGS-4332-316-NE1-XMA_-A120 Typical CGS-4332-316-NE1-U-XDB_-A120
Typical CGS-4332-316-NE1-XX-A120 Top View Top View
Top View
ERSA ®
PARAMUS NJ 07652 U.S.A.

B
B B

A A
Side View Typical CGG-4332-316-NE1-U-XDB_-A120
C Side View
Typical CGG-4332-316-NE1-XMA_-A120
Side View

A
C
Typical CGG-4332-316-NE1-XX-A120 C
Side View

A A

DIMENSIONS Solenoid Options

General Service Hazardous Location
VALVE Standard, -228L -027, 043 C50, -PC -XX, -XN -XISC, -XISX6 -XMA_, XIF_ -XDB_
Function
SERIES A B C A B C A B C A B C A B C A B C A B C
Single solenoid, 2.11 1.75 2.31 2.84 1.75 2.31 3.01 2.47 2.39 2.8 1.89 1.75
E5 — — — — — — — — —
spring return (53.6) (44) (58.7) (204.9) (44) (58.7) (76.5) (62.7) (60.7) (71) (48.2) (44)
5.02 1.56 1.29 3.45 1.56 2.34 5.02 1.04 2.09 3.79 1.31 1.45 3.53 1.31 1.15
C5 Single solenoid, (127.5) — — — — — —
(39.6) (32.8) (87.6) (39.6) (59.4) (127.5) (26.4) (53.1) (96.3) (33.3) (36.8) (89.7) (33.3) (29.2)
spring return
C316 3-Way or 4-Way 5.56 1.63 2.15 — — — 5.56 1.63 2.15 5.56 1.63 2.32 5.43 1.63 2.94 6.59 2.56 4.13 4.63 2.50 4.74
(141.3) (41.3) (54.7) (141.3) (41.3) (54.7) (141.3) (41.3)) (59) (138) (41.3) (74.6) (167.3) (65) (104.8) (117.6) (63.5) (120.3)
Double 7.92 1.56 2.04 7.42 1.56 2.34 7.93 1.56 2.09 8.07 1.56 2.26 7.55 1.56 6.93
C5 — — — — — —
solenoid (201.1) (39.6) (51.8) (188.4) (39.6) (59.4) (201.4) (39.6) (53) (205) (39.6) (57.4) (191.7) (39.6) (176)
3-Way or 5.56 1.63 2.15 8.57 1.63 2.15 8.78 1.63 2.32 8.31 1.63 2.94 10.8 2.56 4.13 6.32 2.50 4.74
C316 4-Way — — —
(141.3) (41.3) (54.7) (217.7) (41.3) (54.6) (223.1) (41.3) (59) (211.1) (41.3) (74.6) (275) (65) (104.8) (160.5) (63.5) (120.3)
www.versa-valves.com 3
 ELECTRICAL

NON HAZARDOUS LOCATION OPERATORS

Suffix Protection Area Classification Certification- Ingress
Identification Classification and (Gas Grouping) (Conformance) Protection

None or NEMA 1,2,

General Purpose Indoor & Outdoor CSA
-HT, PC 3&4

-HC CSA UL NEMA 4;

General Purpose Indoor & Outdoor
-HCC (Shown) (AC only) IP65

-228L General Purpose Indoor & Outdoor UL NEMA 4;

HAZARDOUS LOCATION OPERATORS

Suffix Protection Area Classification Certification- Ingress
Identification Classification and (Gas Grouping) (Conformance) Protection
-XX (see page 6 for
additional coil options) CLASS I, DIV. 1 (C & D)
Hazardous NEMA 7
CLASS I, DIV. 2 (A & B) UL - CSA
-LB-XX (see page 6 for Locations &9
CLASS II, DIV. 1 (E, F & G)
additional coil options)

-XN (see page 6 for

additional coil options) Ex d IIB+H2 T3 to T6 Gb IECEx - INMETRO
IP65&
(d) Flameproof
IP66
-LB-XN (see page 6 for
II 2 G Ex d IIB+H2 T3 to T6 ATEX
additional coil options)

EX II 2 G D ATEX - IECEx IP66, IP67,

Ex de IIC T* Gb -INMETRO & IP68
-U-XDBS* EX tb IIIC T* ºC Db
Cl, I Zone 1 AEx de IIC T* CSAUS
C

Cl, II Zone, 21 AEX tD A21, DIP A21

(d) Flameproof EX II 2 G D ATEX - IECEx
(e) Increased Safety Ex de IIC T* Gb -INMETRO
EX tb IIIC T* ºC Db NEMA 4,
-U-XDBT* Cl I Grp B, C & D, Cl, II Grp E, F & G, Cl III CSAUS 4X
C
Cl, I Zone 1 AEx de IIC T*, Cl, II Zone, 21 AEX 6P
tD A21, DIP A21

-U-XMAA* Ex e mb II T5, T6 Gb
(mb) Encapsulation IECEx IP66
-U-XMAF* Ex tD A21 T100ºC, T85ºC Db
(e) Increased Safety &
-U-XMFA* (tD) Tight Dust II 2 G Ex e mb II T5, T6 ATEX IP67
-U-XMFF* II 2D Ex tD A21 T100ºC, T85ºC

-XISX6* II 2 G EEx ia IIC T6 ATEX

Class I, Groups (A, B, C & D) IP65

-XISC* Intrinsic Safe Class II, Groups (E, F, &G) Factory Mutual CSA
Class III
*-U (upright) suffix recommended for coil housing clearance. For - XDB_ ordering information see “Miscellaneous” column facing page.

OPTIONS
Solenoid Vent Options

The standard solenoid vent is supplied with 10-32 internal thread,

vent to atmosphere. See other options below
-L14: Is a stainless steel screw and filter adapter that provides “Dust
Proof” protection for the solenoid sleeve vent.
-D14: Is a stainless steel adapter with a sealing O-ring that provides
“Water Tight” protection for the solenoid sleeve vent.
-HE and H2E: Are 1/4”-18 npt and 1/8”-27 npt stainless steel Dust Excluders Hydraulic Adapter
adapters, providing a pipe connection to solenoid vent. -L14 -D14 -H2E ⅛”
Dust Proof Water Tight -HE ¼”

4 www.versa-valves.com
 ELECTRICAL

COIL CODES: Identify the solenoid frequency Rating Code Voltage

and voltage consisting of a “Rating Code” and A = 60Hz frequency Indicated by three digits: A120 = AC,120Volts/60hz
“Voltage” as shown at right. Coil codes complete D = Direct Current (DC) e.g. 24 volts = 024
the part number for a solenoid operated valve. E = 50Hz frequency 120 volts = 120

Voltage Electrical
(Power) Characteristics Miscellaneous
All usual 50 Hz & 60 Hz AC (6W) Steel cover with 1/2 NPT conduit hub.
All usual DC (7W)

24V60, 120V60, 240V60 (8.5W) Class F epoxy molded coil Mini DIN socket with PG9 cable gland (-HC) or 1/2” conduit hub
24V50, 110V50, 220V50 (8.5W) (155ºC). (-HCC).
12VDC, 24VDC, 48VDC (10.5W) Continuous duty, 2 leads 24”
(60 cm).
24V60, 120V60, 240V60 (8.5W) Epoxy encapsulated coil with steel 1/2 NPT conduit hub.
24V50, 110V50, 220V50 (8.5W)
12VDC, 24VDC, 48VDC (10.5W

Voltage Electrical
Miscellaneous
(Power) Characteristics
All usual 50 Hz & 60 Hz AC (5.6W) Plated steel coil housing with 1/2 NPT conduit entry.
All usual DC (7.2W) For stainless steel (430 type) coil housing add: (-ST)
12V60, 24V60, 48V60, 120V60, 240V60 Plated steel coil housing with 1/2 NPT conduit entry. For stainless steel
(1.8W) (430 type) coil housing add: (-ST) Maximum pilot pressure 120 psi (8
6VDC, 12VDC, 24VDC, 48VDC (1.8W) bar). 1.8W nominal power.
Class F epoxy molded coil (155ºC).
continuous duty. Plated steel coil housing with M20 x 1.5 conduit entry.
All usual 50 Hz & 60 Hz AC (5.6W)
3 leads 24” (60 cm). Ground terminal on cover.
All usual DC (7.2W) For stainless steel (430 type) coil housing add: (-ST)

12V60, 24V60, 48V60, 120V60, 240V60 Plated steel coil housing with M20 x 1.5 conduit entry.
Ground terminal on cover.
(1.8W)
For stainless steel (430 type) coil housing add: (-ST)
6VDC, 12VDC, 24VDC, 48VDC (1.8W) Maximum pilot pressure 120 psi (8 bar) 1.8W nominal power.

Stainless steel coil housing Suffix Detail Ordering Code

with internal Junction Box. M 20 Connection ½” Connection
24VDC (D024) Internal and external ground
120V60 (A120) 110V50 (E110) screw. No Diode Diode No Diode Diode
230V50 (E230) Epoxy molded coils rated for Standard (vent to atmosphere) XDBS1 XDBS5 XDBT1 XDBT5
continuous duty, Class H – 180°C. 1/8” Adapter (-H2E) XDBS2 XDBS6 XDBT2 XDBT6
1.8 Watt standard, for lower watt contact
1/4” Adapter (-H2) XDBS3 XDBS7 XDBT3 XDBT7
factory.
Dust Nut (-L14) XDBS4 XDBS8 XDBT4 XDBT8
Dust Nut (-D14) XDBS9 XDBS10 XDBT9 XDBT10

Continuous duty coil & rectifier, in- Thick wall epoxy coil housing with integral
24VDC (4W)
cluding surge suppression, potted junction box. Internal ground terminal.
(Consult factory for other voltage)
within housing. M20 x 1.5 conduit entry: (-XMAA), (-XMFA),
Cable gland for 6-12 mm ø cable: (-XMAE), 1/2 NPT conduit entry with
24VDC (10W inrush, 2.6W holding) Continuous duty coil & power adapter: (-XMAF), (-XMFF)
(Consult factory for other voltages) controller potted within housing.
Requires the use of an approved safety barrier or isolator.
24VDC (0.8W) Continuous duty Coil and power Thick wall epoxy coil housing and integral junction box. Internal ground
(Consult factory for other voltages) controller potted within housing. terminal. M20 x 1.5 conduit entry: (-XIFA), Cable gland for 6-12 mm ø
cable: &1/2 NPT conduit entry with adapter: (-XIFF)

Options
Overrides Solenoid Orientation
C5 Valves* C316 Valves C316 Valves

Standard; -M; -CML; -ME; Unguarded,

momentary Unguarded, Knurled knob momentary contact In line solenoid Upright solenoid (-U)
contact momentary twist to lock standard
contact
*E5 not available with override Note: -U for C316 valves only
www.versa-valves.com 5
 COMBINATION SUFFIX DETAILS

Hazardous Location Combination Suffix Details

Cross Reference Chart
Suffix Reference North American (-XX) (Cont.) ATEX (XN) (Cont.)
Suffix Description Combination Combination
Included Suffix Included Suffix
-XX North American solenoid Suffix Suffix
-XN ATEX solenoid -XXK4 -XX, -D14, -HT, -LB, -PC, -ST -XNM -XN, -HT, -PC
-XDB World Solenoid -XXL -XX, -PC -XNN -XN, -LB, -PC
-XXL4 -XX, -D14, -PC -XNN4 -XN -D14, -LB, -PC
-HT Class H coil -XXM -XX, -HT, -PC
-ST Stainless solenoid housing -XNP -XN, -HT, -LB, -PC
-XXM4 -XX, -D14, -HT, -PC
-PC Potted coil -XXN -XX, -LB, -PC -XNQ -XN, -HT, -LB
-LB 1.8 watt solenoid -XXN4 -XX, -D14, -LB, -PC -XNR -XN, -LB
-LA 0.85 watt solenoid -XXP -XX, -HT, -LB, -PC -XNS -XN, -LA, -ST
-VJBT Add on Junction Box -XXP4 -XX, -D14, -HT, -LB, -PC -XNS4 -XN, -D14, -LA, -ST
-XXQ -XX, -HT, -LB -XNU -XN, -HT, -LB, -ST
-D14 Solenoid vent, water proof nut -XXQ4 -XX, -D14, -HT, -LB
-PS Potted coil, male conduit -XXR -XX, -LB -XNV -XN, -LA
-CD 72” wire leads -XXR4 -XX, -D14, -LB -XNV4 -XN, -D14, -LA
-LX 1.8 watt solenoid -XXS -XX, -LA, -ST -XNX -XN, -LB, -PS
-H2E 1/8” npt solenoid vent -XXS4 -XX, -D14, -LA, -ST -XNWS -XN, -VJBT, -LB, -PS
-XXU -XX, -HT, -LB, -ST
-HE ¼” npt solenoid vent
-XXU4 -XX, -D14, -HT, -LB, -ST World Solenoid (XDB)
-L14 solenoid vent dust nut -XXV -XX, -LA Combination
-303D Integral diode -XXV4 -XX, -D14, -LA Included Suffix
Suffix
-XXW -XX, -CD, -HT, -H2, -PC, -ST -XDBS1 -XDBS, -HT, -LX
-XXW4 -XX, -D14, -CD, -HT, -PC, -ST
North American (-XX) -XDBS2 -XDBS, -HT, -LX, -H2E
-XDBS3 -XDBS, -HT, -LX, -HE
Combination Included Suffix -XDBS4 -XDBS, -HT, -LX, -L14
Suffix
-XXA -XX, -HT ATEX (XN) -XDBS5 -XDBS, -HT, -LX, -303D
-XXA4 -XX, -D14, -HT Combination -XDBS6 -XDBS, -HT, -LX, -H2E, -303D
Included Suffix
-XXB -XX, -PS Suffix -XDBS7 -XDBS, -HT, -LX, -HE, -303D
-XXB4 -XX, -D14, -PS -XNA -XN, -HT -XDBS8 -XDBS, -HT, -LX, -L14, -303D
-XXC -XX, -HT, -PS -XND -XN, -ST -XDBS9 -XDBS, -HT, -LX, -D14
-XXC4 -XX, -D14, -HT, -PS -XNE -XN, -PC, -ST -XDBS10 -XDBS,-HT,-LX,-D14, -303D
-XXD -XX, -ST -XNE4 -XN, -D14, -PC, -ST
-XXD4 -XX, -D14, -ST -XDBT1 -XDBT, -HT, -LX
-XXE -XX, -PC, -ST -XNF -XN, -HT, -ST -XDBT2 -XDBT, -HT, -LX, -H2E
-XXE4 -XX, -D14, -PC, -ST -XNG -XN, -LB, -ST -XDBT3 -XDBT, -HT, -LX, -HE
-XXF -XX, -HT, -ST -XNH -XN-HT, -PC, -ST -XDBT4 -XDBT, -HT, -LX, -L14
-XXF4 -XX, -D14, -HT, -ST -XNJ -XN, -LB, -PC, -ST -XDBT5 -XDBT, -HT, -LX, -303D
-XXG -XX, -LB, -ST -XNJ4 -XN, -D14, -LB, -PC, -ST -XDBT6 -XDBT, -HT, -LX, -H2E, -303D
-XXG4 -XX, -D14, -LB, -ST -XNK -XN, -HT, -LB, -PC, -ST
-XXH -XX, -HT, -PC, -ST -XDBT7 -XDBT, -HT, -LX, -HE, -303D
-XXJ -XX, -LB, -PC, -ST -XXK4 -XN, -D14, -HT, -LB, -PC, -ST -XDBT8 -XDBT, -HT, -LX, -L14, -303D
-XXJ4 -XX, -D14, -LB, -PC, -ST -XNL -XN, -PC -XDBT9 -XDBT, -HT, -LX, -D14
-XXK -XX, -HT, -LB, -PC, -ST -XNL4 -XN -D14, -PC -XDBT10 -XDBT, -HT, -LX, -D14, -303D

Recommended Hazardous Location Certification/Power

Solenoid Option Packages North American - CSA ATEX - IECEx - INMETRO

Enclosure/Wire Standard Power Low Watt* Standard Power Low Watt*

Steel, Electroless Nickel Plated, 24 Inch Leads -XXL4 -XXN4 -XNL4 -XNN4
Stainless Steel, High Performance 430 type, 24 Inch leads -XXE4 -XXJ4 -XNE4 -XNJ4
Stainless Steel, 316L type, Junction Box with Terminal Strip n/a -U-XDBT9** n/a -U-XDBS9
* 1.8 watt solenoid. Also available is 0.85 watt, see cross reference chart above. For 0.50 watt, consult factory.
** All the –XDBT type solenoids are “World Solenoids.” Certified for North America, ATEX, IECEx and INMETRO

Miscellaneous: Actuator Speed

Actuator Speed ACTUATOR VOLUME in3 (cm3) For double-acting actuators (open & closed), use
Valve 5 10 25 50 100 150 200 400 600 1000 volumes from selected actuator specifications and the
Type (82) (162) (410) (820) (1641) (2460) (3280) (6560) (9840) (16400) chart for estimated speed. The times indicated are per
Actuator Cycle C5/C316 .32 .36 .47 .63 .98 1.3 1.7 3.1 4.5 7.2 shift. For spring return actuators, use open volume to
time in seconds E5 .46 .64 1.1 2.0 3.9 5.7 7.5 — — — obtain time from chart. Actuator spring loading may
affect shift time.
The above chart represents approximate actuator operation times under average load conditions at 80 psi Slower speeds (adjustable) can always be
(5.5 bar). Due to differing designs of quarter-turn actuators, breakaway friction, loading, internal airflow, inlet accomplished by using Versa’s Bleed Control Valves
piping, fittings and exhaust port options, the values shown are intended as an estimate. Faster or slower times
in the control valve exhaust port.
may actually be achieved.

6 www.versa-valves.com
DIRECT MOUNT ACTUATOR VALVES
Accessories
Versa NAMUR ReBreather Versa Dual Speed Control
Actuator Controls For Harsh Or Dirty Environments Actuator Controls For Harsh Or Dirty Environments
Introduction Description
A valve accessory to protect valves and actuators from harsh A simple device to control actuator speed in applications where
and corrosive atmospheres. Designed to prevent the actuator the environment is corrosive from production, plant pollutants
spring chambers from sucking in external air and contaminants or other environmental issues. The Dual Speed Control
during the return stroke. Accessory protects the actuator package from external air and
contaminants.
How it works
The Rebreather block is used on single acting actuators to How it works
prevent corrosive atmosphere from entering the actuator The Versa Dual Speed Control block is used on double acting
spring side. This add-on accessory is also designed to use actuators to prevent corrosive atmosphere from entering the
available instrument air to fill spring side, thus assuring only valve package (actuator and solenoid NAMUR valve). This add-
clean air enters the actuator. on accessory includes 2 of Versa’s proven “Bleed Controls” to
allow independent adjusting of open and close speeds.
The instrument air it utilizes on the return stroke is from the
exhaust cycle of the piston side of actuator. No additional air
is required to complete the cycle and keep the actuator clean,
hence the reason this accessory is called a “ReBreather”
reusing clean exhaust air to keep the actuator clean. CGS-3331-316-NX1-DBC2-HCC-D024
Shown
CGS-3331-316-NE1-RB5-XX-D024
Shown

ORDERING INFORMATION
As a Kit As a Kit
C Series C 316 Series Description C Series (-NB/-NX) C 316 Series (-NE) Description
C-33RB-NB C-33RB-NE Plate, ¼” npt vent port open Plate and speed controls with ¼”
C-43SC-NB C-43SC-NE
Plate, and speed control, with ¼” npt vent port open**
C-33RB-NB-BC C-33RB-NE-BC npt vent port open Plate and speed controls with
C-43SC-NB-DB3 C-43SC-NE-DE3 DE-3 in vent port**
C-33RB-NB-DE3 C-33RB-NE-DE3 Plate, with DE-3 in vent port**
Plate, and speed control, with
C-33RB-NB-BC-DE3 C-33RB-NE-BC-DE3 DE-3 in vent port
C-33RB-NB-MFS3 C-33RB-NE-MFS3 Plate, with MFS-3 in vent port
Plate, and speed control, with
C-33RB-NB-BC-MFS3 C-33RB-NE-BC-MFS3 MFS-3 in vent port

On a Valve On a Valve
Suffix* Description Suffix* Description Suffix* Description
Plate, ¼” npt vent port -RB1 Plate, and speed control, with -DBC Plate and speed controls with ¼” npt vent port† for -NE valves
-RB open ¼” npt vent port open -DBC1 Plate and speed control with ¼” npt vent port† for NB/-NX valves
-RB2 port**with DE-3 in vent
Plate, -RB3 Plate, and speed control, with -DBC2 Plate and speed control with DE-3 in vent port for -NB/-NX valves
DE-3 in vent port
-DBC3 Plate and speed control with DE-3-316 in vent port for -NE valves
-RB4 Plate, with MFS-3 in vent -RB5 Plate, and speed control, with
port MFS-3 in vent port *Add suffix to complete C/C316 series valve part number.
**Aluminum DE on C Series and Stainless on C-316 Series
† Customer supplied excluder

Actuator, Actuator,
Spring Return Double Acting

C Series 3-way C Series 4-way

NAMUR Valve NAMUR Valve

ReBreather Block Dual Speed

w/ Optional Control Block w/
Speed Control optional Dust
Excluder

www.versa-valves.com 7
 Versa
has been
supplying the
oil and gas
industr y with
pneumatic
and hydraulic
components
for over 50
years. We
have built a
reputation
for quality
that is
unsur passed
in the market
for high
perfor mance
solenoids,
pneumatic
relays, resets
and pilot
valves

WARNINGS REGARDING THE DESIGN APPLICATION,

INSTALLATION AND SERVICE OF VERSA PRODUCTS

The warnings below must be read and reviewed before designing a system utilizing,
installing, servicing, or removing a Versa product. Improper use, installation or servicing of LIMITED WARRANTY DISCLAIMER
a Versa product could create a hazard to personnel and property. AND LIMITATION OF REMEDIES
DESIGN APPLICATION WARNINGS Versa’s Series products are warranted
Versa products are intended for use where compressed air or industrial hydraulic fluids are to be free from defective material and
present. For use with media other than specified or for non-industrial applications or other workmanship for a period of ten years
applications not within published specifications, consult Versa. from the date of manufacture, provided
Versa products are not inherently dangerous. They are only a component of a larger said products are used in accordance
system. The system in which a Versa product is used must include adequate safeguards with Versa specifications. Versa’s
to prevent injury or damage in the event of system or product failure, whether this failure liability pursuant to that warranty
be of switches, regulators, cylinders, valves or any other system component. System is limited to the replacement of the
designers must provide adequate warnings for each system in which a Versa product
is utilized. These warnings, including those set forth herein, should be provided by the Versa product proved to be defective
designer to those who will come in contact with the system. provided the allegedly defective
product is returned to Versa or its
Where questions exist regarding the applicability of a Versa product to a given use, inquiries authorized distributor. Versa provides
should be addressed directly to the manufacturer. Confirmation should be obtained directly
from the manufacturer regarding any questioned application prior to proceeding. no other warranties, expressed or
implied, except as stated above.
INSTALLATION, OPERATION AND SERVICE WARNINGS There are no implied warranties
Do not install or service any Versa product on a system or machine without first of merchantability or fitness for a
depressurizing the system and turning off any air, fluid, or electricity to the system or
machine. All applicable electrical, mechanical, and safety codes, as well as applicable particular purpose. Versa’s liability for
governmental regulations and laws must be complied with when installing or servicing a breach of warranty as herein stated is
Versa product. the only and exclusive remedy and in
no event shall Versa be responsible or
Versa products should only be installed or serviced by qualified, knowledgeable personnel
who understand how these specific products are to be installed and operated. The liable for incidental or consequential
individual must be familiar with the particular specifications, including specifications for damages.
temperature, pressure, lubrication, environment and filtration for the Versa product which
is being installed or serviced. Specifications may be obtained upon request directly from
Versa. If damages should occur to a Versa product, do not Operate the system containing
the Versa product. Consult Versa for technical information.

Versa Products Company, Inc. Versa BV

22 Spring Valley Road Prins Willem Alexanderlaan 1427
Paramus, New Jersey 07652 7312 GB Apeldoorn
USA The Netherlands
Phone: (201) 843-2400 Phone: +31-55-368-1900 www.versa-valves.com
Fax: (201) 843-2931 Fax: +31-55-368-1909 email: [email protected]