SP928 CCD

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

3.3.1.

5 Cameras for BeamGage®


3.3.1.5.1 190-1100nm USB Silicon CCD Cameras

SP907 low resolution and SP928 high resolution


Features
ֺֺ 1/1.8 imager format
ֺֺ Small camera size
ֺֺ 56dB true dynamic resolution

3.3.1.5.1 Beam Analysis


SP300 High resolution, high speed
Features
ֺֺ 1/1.8 imager format
ֺֺ High resolution
ֺֺ High speed
ֺֺ 56dB true dynamic resolution

173
For latest updates please visit our website: www.ophiropt.com/photonics 01.01.2018
Item Specification
Model SP907 SP928 SP300
Application 1/1.8” format 1/1.8” format 1/1.8” format
Spectral Response 190 - 1100nm (2) 190 - 1100nm (2) 190 - 1100nm (2)
Active Area 7.1mm x 5.3mm 7.1mm x 5.3mm 7.1mm x 5.3mm
Pixel spacing 7.38μm 3.69μm 3.69μm
Number of effective pixels 964 x 724 1928 x 1448 1928 x 1448
Minimum system dynamic range 56 dB 56 dB 56 dB
Linearity with Power ±1% ±1% ±1%
Accuracy of beam width ±2% ±2% ±2%
Frame rates in 12 bit mode (4) 23 fps at full resolution 13 fps at full resolution 26 fps at full resolution
Shutter duration 30μs to multiple frames 30μs to multiple frames 30μs to multiple frames
Gain control 0 dB to 24 dB 0 dB to 24 dB 0 dB to 24 dB
Trigger Hardware/Software trigger & strobe Hardware/Software trigger & strobe Hardware/Software trigger & strobe
out out out
Photodiode trigger Si response: SP90408 Si response: SP90408 Si response: SP90408
Saturation intensity (1) 0.97µW/cm2 0.97µW/cm2 0.97µW/cm2
Lowest measurable signal (1) 1.2nW/cm2 1.2nW/cm2 1.2nW/cm2
Damage threshold 50W/cm2 / 0.1J/cm2 with all filters installed for < 100ns pulse width(3)
Dimensions 48 mm x 44 mm x 20.2 mm 48 mm x 44 mm x 20.2 mm 44 mm x 29 mm x 58 mm
CCD recess 4.5 mm 4.5 mm 17.5 mm
Image quality at 1064nm Pulsed with trigger sync - excellent Pulsed with trigger sync - excellent Pulsed with trigger sync - excellent
Pulsed with video trigger - good Pulsed with video trigger - good Pulsed with video trigger - good
CW - good CW - good CW - good
Operation mode Interline transfer CCD Interline transfer CCD Double tap interline transfer CCD
Software supported BeamGage STD or PRO BeamGage STD or PRO BeamGage STD or PRO
PC interface USB 3.0 USB 3.0 USB 3.0
OS Supported Windows 7 (64) and Windows 10
Notes: (1) Camera set to full resolution at maximum frame rate and exposure times, running CW at 632.8nm wavelength. Camera set to minimum useful
gain for saturation test and maximum useful gain for lowest signal test.
(2) Camera may be useable for wavelengths below 350nm but sensitivity is low and detector deterioration may occur. Therefore UV image
converter is recommended. Although our silicon cameras have shown response out to 1320nm it can cause significant blooming which could
lead to significant errors of beam width measurement. We would suggest our XC130 InGaAs camera for these wavelengths to give the best
measurements.
(3) This is the damage threshold of the filter glass of the filters. Assuming all filters mounted with ND1 (red housing) filter in the front. Distortion of
the beam may occur with average power densities as low as 5W/cm2.
(4) Highly dependent on PC processor and graphics adapter performance.

3.3.1.5.2 190-1100nm GigE Silicon CCD Cameras


SP920G high resolution
Features
3.3.1.5.2 Beam Analysis

ֺֺ 1/1.8 imager format


ֺֺ Small camera size
ֺֺ 56dB true dynamic resolution
ֺֺ GigE interface

5mm 2X M3X0.5 .157in[4mm]


.197in

26mm
1.024in

M2 JACKSCREW
GIGABIT ETHERNET BOSS
CONNECTOR
57.50mm 8 PIN GPIO
44mm 8mm 2.264in CONNECTOR
1.732in .315in
STATUS LED

29mm
1.142in 21.73mm
.856in 14.50mm
.571in

ACTIVE AREA 14.25mm


ACTIVE AREA: 17.53mm
7.1mm X 5.3mm .690in .561in 7.25mm
22mm .285in
.866in

32.88mm
1.294in
50mm
5mm 1.969in 4X M3X0.5 .157in[4mm]
.197in

PART NO. DESCRIPTION


26mm
1.024in SP90519 BGS-GIGE-SP920G
SP90520 BGP-GIGE-SP920G

174
15.07.2018 For latest updates please visit our website: www.ophiropt.com/photonics

You might also like