Scribd
Upload
30 views3 pages

Control para Piscina

This document provides instructions for a CTR-RM-Switch LED controller. The controller can remotely control power systems using a 433MHz RF remote up to 30 meters away. It is suitable for switching LM-PAR56 lamps and can control multiple controllers with a single remote. The controller operates on 110V/220V AC and connects to lamps or transformers with output power up to 500W/1000W.

Uploaded by

asd consultores
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
30 views3 pages

Control para Piscina

This document provides instructions for a CTR-RM-Switch LED controller. The controller can remotely control power systems using a 433MHz RF remote up to 30 meters away. It is suitable for switching LM-PAR56 lamps and can control multiple controllers with a single remote. The controller operates on 110V/220V AC and connects to lamps or transformers with output power up to 500W/1000W.

Uploaded by

asd consultores
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Page 1 / 3

LED CONTROLLER ITEM NO.: CTR-RM-Switch

INSTRUCTION OF CTR-RM-Switch
Controllers' Insturction and application
Control the relay by remoter to on/off the power system easily. This controller
is used for on-off work in high and far away places.
This controller is quite suitable for switch mode LM-PAR56 lamps,it can
achieve a key to switch the functions of lamps and a key to reset lamp function.

A. Specification
Size: L240 x W84 x H39.1mm
Material: aluminum alloy
Weight: 0.65KG
Input voltage: 110V/220V AC(50~60HZ)
Remote distance: 30m(max)
Protection: IP65
Output Power(max): 500W/1000W

B. Remote controller
B-1. Character
Size: 75x40x15mm
Frequency: 433MHz (RF)
Battery: 12V(23A type)
Remote distance: more than 30M

B-2. Function and Button Caution:


, : ON/OFF 1 Please read the manual carefully
before operation
, , : Switch 2 Please take the battery out if out
: Reset of work for long time
3 If remote distance become shorter,
please change the battery
4 Please use our original remoter(RM-G).

B-3. Pairing of remote control

1. Press the white bottom on the controllers while powering on ,the previous paring
remoter ID code will be cleared.
2. Press any bottom of the remoter, it will automatically save the remoter's ID in the
controllers to complete the pairing.
3. Supporting one remoter pairs many of controllers.

Note:.When LM-PAR56 lamps can not work under same function,press reset button " ",then all lights
will go back to first function, that is Static Red.Interval time for on/off operation:2 seconds.

C. Dimension Drawing
Page 2 / 3

LED CONTROLLER ITEM NO.: CTR-RM-Switch

84 39.1

240
D.Mounting holes size

75

Pairing button
/
O4.5

Singal pilot lamp Power pilot lamp


138

Connection box(High
AC voltage）
Page 3 / 3

LED CONTROLLER ITEM NO.: CTR-RM-Switch

E. Connection

E-1. Recommended control mode and lamp

50 2 1 Controller with
remoter

AC12V AC110V/220V
Transformer

E-2.Other control modes and lamps

Controller with
remoter

AC110V/220V

Note:.When lamps are AC input type,pls only use button and , we do not suggest using other buttons cause this might
cause some bad effect to the power supply in fixtures.

Warning：

1、 When plug in high AC power,pls drag out the AC input cable ;


2、 When used in outside,pls be sure to deal the plugs,connection wire
waterproof well ;
3、Pls advoid any severe shake/drop,or lead to products'failure;
4、Don't open it without sellers' permit.

You might also like