Premierflex 3000

PREMIERFLEX-3000
SBS Modified Waterproofing Membrane
DESCRIPTION QUALITY CONTROL
BITUMAT PREMIERFLEX-3000 is an SBS In addition to stringent regular tests by BITUMAT

modified bitumen waterproofing membrane laboratory, our products are tested periodically by
re-inforced with spunbonded polyester mat. The Independent Laboratories like SOCOTEC.
combination gives the proven waterproofing
qualities of bitumen along with elasticity, and STANDARDS
excellent resistance to weathering and ease of
application. BITUMAT PREMIERFLEX-3000 complies with the
requirements and tolerance levels of :
USES 1. The American Society for Testing and Materials
ASTM D 6164 Type II.
BITUMAT PREMIERLEX-3000 is a general purpose 2. European Union of Technical Agreement
waterproofing membrane and is excellent in (UEAtc) MOAT 31-1984 and MOAT 30-1984.
multi- layer or single layer roofing system. When 3. CGSB (Canadian General Standards Board)
surfaced with granular slate, BITUMAT 37-GP56M-July 1980.
PREMIERFLEX-3000 is ideal as an exposed top
layer. BITUMAT PREMIERFLEX-3000 is also INSTALLATION TOOLS REQUIRED:
suitable for underground waterproofing. Suitable Gas torch, Knife, Trowel, Measuring tape,
for moderately cold or hot climates. Marking string and Gloves.
OUTSTANDING FEATURES APPLICATION
• Good cold weather resistance BITUMAT PREMIERFLEX-3000 is installed by

• High tensile strength and tear resistance torch welding method, loose-laid or fully bonded
to substrate. When loose-laid, only overlaps are
• Good elongation and recovery bonded together. Peripheres and protrusions are
• Very good puncture resistance sealed according to specifications.
• Resistant to substrate movement
COVERAGE RATE (Approx.)
GENERAL DATA (Rate may vary as per site requirement)
Flat areas : 1.15 M2/M2 per layer with 10
Nominal Roll length : 10 Mtrs. cms. side laps and 15 cms.
Nominal Roll width : 1M end laps.
Nominal Thickness : 3,4,5 MM Base flashing : 100x35 cms. with 15 cm. end
Reinforcement : Spunbonded polyester laps, 0.40 M2/ linear M
mat. Average wastage : 3 - 5 %
PACKAGING TORCHING GUIDELINES

The underside of the membrane should be torched
• 3mm - 28 rolls / pallet just enough to superficially melt the
• 4mm - 23 rolls / pallet bitumen. Excessive heating may damage the
re-inforcement.
• 5mm - 16 rolls / pallet
Overlaps should be re-heated from the top and
FINISHES resealed with a trowel to ensure seam integrity.
BITUMAT PREMIERFLEX-3000 is available in two For details of installation methods and flashing
basic finishes: requirements, consult the relevant BITUMAT
• Black smooth finish with polyethylene Systems Design and Installation Manual.
surfaces for covered applications.
• Granule surfacing for exposed
applications.
PREMIERFLEX-3000
SBS Modified Waterproofing Membrane
TECHNICAL DATA
Property Typical Value Test Method
1. Softening point, °C 115 ASTM D 36
2. Penetration, @ 25 °C dmm 30 ASTM D 5
3. Low temperature flexibility, °C -15 to -18 ASTM D 5147
4. Heat resistance, Compound stability
@ 102 °C for 2 hours & 15 minutes No flow - Pass ASTM D 5147
5. Tensile strength, N/5 cm @ 23+2 °C
Longitudinal 800 (16 KN/m) ASTM D 5147
Transverse 600 (12 KN/m)
6. Tensile strength, N/5 cm @ -18+2 °C
Longitudinal 1000 (20 KN/m) ASTM D 5147
Transverse 750 (12.5 KN/m)
7. Elongation, % @ 23+2 °C
Longitudinal 40 ASTM D 5147
Transverse 45
8. Elongation, % @ -18+2 °C
Transverse 25
9. Load strain product @ 23+2 °C
Longitudinal 32,000 CGSB-37-GP-56M
Transverse 27,500
10. Load strain product @ -18+2 °C
Longitudinal 25,000 CGSB-37-GP-56M
Transverse 18,750
11. Lap joint strength, N/5 cm @ 25+2 °C
Same as membrane CGSB-37-GP-56M
Longitudinal
Transverse UEAtc
12. Tear resistance, N @ 23+2 °C
Transverse 400
13. Puncture resistance, N @ 25+2 °C 950 ASTM E 154,
Static indentation L3 UEAtc 5.1.9.
Dynamic indentation I3 UEAtc 5.1.10
14. Water absorption, % Wt @ 23°C / 24 hrs. <0.25 ASTM D 5147
15. Water vapour transmission, <0.30 ASTM E 96 procedure
g/m2/24 hrs. E 37.8 °C at 90% RH
16. Dimensional stability, %
Longitudinal + 0.5 ASTM D 5147
Transverse + 0.5
17. Resistance to leakage at joints Pass UEAtc
18. Resistance to aging & U.V. No change greater than ASTM
20% of the original G53
values UNI 8202
The information given in this Technical Data Sheet reflects typical median properties based on laboratory test, and practical experience; subject
to the tolerance levels of UEAtc directives. However, as the product is often used under conditions beyond our control, we can’t warrant but the
product itself.
THIS PUBLICATION AUTOMATICALLY SUPERSEDES ALL PREVIOUS PUBLICATIONS RELATING TO THIS PRODUCT.
MSD O9/2003

Premierflex 3000

Uploaded by

Copyright:

Available Formats

Premierflex 3000

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Premierflex 3000

Uploaded by

Copyright:

Available Formats

PREMIERFLEX-3000

SBS Modified Waterproofing Membrane

DESCRIPTION QUALITY CONTROL

BITUMAT PREMIERFLEX-3000 is an SBS In addition to stringent regular tests by BITUMAT

OUTSTANDING FEATURES APPLICATION

• Good cold weather resistance BITUMAT PREMIERFLEX-3000 is installed by

PACKAGING TORCHING GUIDELINES

You might also like