Digital Speaker

Processor

USER′S MANUAL
Digital speaker processor

Attention
Thank you for purchasing our digital speaker processor. This product is built on the basis of
excellent quality, excellent product quality in the frequency division, equalization and signal processing
market in a leading position.
Before using the machine, please read through the operation manual so that you can master how to use
the equipment correctly. After you have read the manual, please keep it properly for future reference.
Please note: the machine is electrical products, non-professional maintenance technicians, do not
disassemble the machine without authorization, so as to avoid the risk of electric shock (shock). In
case of failure, please contact your distributor or manufacturer.

Function Introduction

The processor adopts the most advanced DSP technology, using 24bit, 48K A/D, D/A converter,
with 128k sampling rate. Digital processing includes gain, phase reversal, noise gate, equalizer,
slope filter, dynamic filter, frequency division, delay, compression, clipping, and signal routing functions,
all through a high-performance DSP processor. Balanced output and RF protection are used for all
inputs and outputs, while the XLR connector is used.

Factory Configuration

As part of our quality control system, each product is carefully inspected before leaving the factory
to make sure there are no defects in its appearance. After opening the package, please check for any
physical damage. Please keep the transport wooden cases and all the packing materials, as they are
specially designed for this product. If the equipment needs to be repacked for transportation, the use
of these materials and wooden cases will minimize the possibility of damage during transportation. In
the event of damage, please notify your dealer immediately and issue a written statement of all damage.
If the carrier is not notified in time and if the carrier is unable to inspect the shipping cases and packing
materials, you will lose all claims against the common carrier.

Digital audio processor 1pcs

Power line 1pcs
Computer cable 1pcs
Data disc/usb flash disk 1pcs
Product manual book 1pcs
Product qualified certificate 1pcs

~1~
 Digital Speaker Processor

Panel Introduction

1 3 4 5 6 7 9

2 8 10

11 12 13 14 15 16

1. USB connection indicator light, which is on when connecting USB interface to PC control terminal.
2. Front panel USB interface -- can be connected to the computer special software to adjust the parameters
of the device.
3. LCD screen -- displays menu options and various parameter information.
4、PM1/Enter——parameter selection and confirmation key. Select the required parameters by rotation and
press the switch to enter the parameters menu.
5、PM2/Back——parameter adjustment and return key. Adjust the parameter value by rotating, press the
switch to return to the upper menu and exit.
6、PM3/Menu——parameter adjustment and Menu key. By rotating to adjust the parameter value, pressing
the switch is to enter the function menu.
7、Input level indicates status lamp. -15dBu to +15dBu is the normal signal indicator, CLIP is the peak
indicator, and CMP is the compressor starting indicator.
8、Enter mute and parameter editing button -- press this button, and the green LED indicator of the
corresponding channel will be lit, indicating the parameter editing menu of the channel. Parameters can
be adjusted through the display screen and three encoders. Press this button for a long time (about two
seconds), and the red indicator of the channel will be lit, indicating that the mute function of the
channel is started.。
9、Output level indicates status lamp. -15dBu to +15dBu is the normal signal indicator, CLIP is the peak
indicator, and LIMIT is the starting indicator of the voltage limiter.
10、Output mute and parameter editing button -- press this button, and the green LED indicator of the
corresponding channel will be lit, indicating the parameter editing menu of the channel. Parameters can
be adjusted through the display screen and three encoders. Press this button for a long time (about two
seconds), and the red indicator of the channel will be lit, indicating that the mute function of the channel
is started.
11、AC power input standard IEC plug and power main switch, can use AC 220V to 240V@ 50 and 60 Hz
voltage, with voltage regulation and power failure protection functions.
12、RS485 interface is used to connect PC control terminal or central control platform.
13、Rear panel USB interface -- can be connected to the computer special software to adjust the parameters
of the device, the front and rear USB interface can only be used at the same time.
14、Eight -channel output signal XLR balanced interface.。
15、The chassis ground switch is pressed to indicate the connection between the ground wire and the
chassis; otherwise, it is disconnected.
16、Four -channel input signal XLR balanced interface.

~2~
Digital Speaker Processor

Parameter Settings
1. Mute
Press the button of the corresponding channel for a long time (about two seconds), and the red indicator
of the channel will be lit, indicating that the mute function of the channel is started. Input/output no audio
output. To cancel the mute, press the button of the corresponding channel for a long time (about two
seconds), and the red light of the channel will go out, indicating that the mute is cancelled.

2. Edit the channel name

Press the corresponding input IN A, B, C, D/ output channel OUT 1, 2, 3, 4, 5, 6, 7, 8, then press
Enter key, edit the name through PM2, and press Back to return.

3. Noise door
Press the corresponding input channel and rotate PM1 to the following interface.

Press Enter to adjust the parameters through the three encoders. Including straight through switch (Byp)
(note: On is to close the noise gate, Off is to open the noise gate), threshold value (Thr), release time (Rel),
start control time (Atk), and press Back to return.

4. Gain
Press the corresponding input/output channel, rotate PM1 to the following interface, press Enter, adjust the
parameters through PM2 and PM3, and press Back to return.

Out-1 Out1 Gain

-> Gain = 0.0dB

5. Phase
Press the corresponding input/output channel, rotate PM1 to the following interface, press Enter, adjust
the phase through PM2 or PM3, positive phase(Normal), inverse phase(Invert), and press Back to return.

6. Delay
Press the corresponding input/output channel, rotate PM1 to the following interface, press Enter key, adjust
the delay time (ms) or distance (m) through PM2 and PM3, and press Back to return.

~3~
 Digital Speaker Processor

Parameter Settings
7. Input channel compressor/output channel limiter
Press the corresponding input/output channel, rotate PM1 to the following interface, and press Enter to
adjust the parameters through PM2 and PM3. Bypass switch (note: On is to close the compressor, Off is
to open the compressor)

Continue to rotate PM1 to adjust the start Threshold.

Continue to rotate PM1 to adjust the compression Ratio and the compression inflection point (Knee).

Continue to rotate PM1 to adjust the compressor's release time (Rel) (in seconds) and start time (Atk)
(in milliseconds). Press Back to return.

Continue rotating PM1 to adjust the compressor to Make-up=0.0dB.

8. Parametric equilibrium
Press the corresponding input/output channel, rotate PM1 to the following interface, and press Enter
key. Through PM2 to adjust switch(Bypass) (Note: On indicates to turn Off all EQ of the channel, and
OFF indicates to turn on all EQ of the channel). Input segments PEQ-01 to PEQ-30, and output
segments PEQ-01 to PEQ-07.

Press Back to return, continue to rotate PM1 to the following interface, and press Enter to adjust whether
this section EQ is turned On by PM2 (Byp=On is straight through, Byp=Off is turned On), and PM3 to adjust
the EQ type.The first and last section EQ can be set to the Peaking_EQ/ Hi-Shelv Q/ Lo-Shelv Q type, while
the other sections EQ can only be adjusted to the Peaking EQ type.

~4~
 Digital Speaker Processor

Parameter Settings

Continue to rotate PM1 to the following interface and adjust EQ frequency points through PM2 and PM3.

Continue rotating PM1 to the following interface to adjust EQ gain and Q values by PM2 and PM3.
Press Back to return when finished, and adjust other EQS according to this method.。

9. Select the input source of the output channel

Press the corresponding output channel, rotate PM1 to the following interface, press Enter, rotate PM2 to
select the sound source of the output channel. The sound sources are IN A/IN B/IN C/IN D. Press Enter
key to adjust the volume of input source and open/close channel input source. Press Back to exit after
adjustment.

10. Frequency division

Press the corresponding output channel, rotate PM1 to the following interface, press Enter, PM1 and PM2
can adjust the frequency points of the high-pass filter, and PM3 can adjust the slope of the high-pass filter,
the higher of the value, and the slope also higher, the low-frequency will be cutting more, Bypass is the
through state. Press Back to exit.

Continue to rotate PM1 to the following interface, press Enter, PM1 and PM2 can adjust the frequency
points of the low-pass filter, PM3 can adjust the slope of the low-pass filter, the higher of the value, and
the slope also higher, the high-frequency will be cutting more, Bypass is the direct state.

~5~
 Digital Speaker Processor

Function Menu

1. System Utilities
Press the MENU key to enter the system application setting interface:

At this point, press Enter key, and Enter the sub-menu of system application, and then use three encoders
and keys to achieve the purpose of setting parameters.Submenu features include the following types:

A. Delay Units setting. Enter the menu to change the expression unit of delay device, Time(ms)
represents the time millisecond, Distance(m) represents the distance meter.

B. Restore Default Setting. Enter the menu to restore factory default Settings.

C. User name Display (Firmware Version).

2、Preset setting（Program Utilities）

Press the MENU key and rotate PM1 to enter the preset setting interface:

At this point, press Enter to Enter the submenu of preset Settings, and then use three encoders and
buttons to achieve the purpose of setting parameters. Submenu features include the following types：

A. Recall A Preset. If you enter the submenu, you can call the preset saved by the user. If the user has
not saved the preset, it will show that it cannot be retrieved.

~6~
 Digital Speaker Processor

Function Menu
B. Save a Preset. Enter the submenu to save the current parameters to the preset, you can also edit
the preset name, easy access. A total of 48 presets can be saved.

C. Delete a Preset. You can delete 48 presets by entering the submenu.

3. Interface Setting
Press the MENU key and rotate PM1 to enter the interface setting interface:

Press Enter key into the sub-menu of interface Settings. You can select RS485 in online mode and
select the corresponding ID(01-32). PM2 adjustable ID: 01-32, and press PM2 to return.

4. Security Utilities
Press the MENU key to enter the safety setting interface:

At this point, press Enter to Enter the sub-menu of system application, and then use three encoders
and keys to achieve the purpose of setting parameters. Submenu features include the following types:

A. Show Parameter. Be shown indicates that when the device is locked, the parameters are displayed,
but cannot be adjusted; No be shown indicates that when the device is locked, the parameters are not shown.

~7~
 Digital Speaker Processor

Function Menu

B. Lock Unit. If the device is not locked, all parameters can be edited. If the machine is locked (the Lock
Interface is set ON), all parameters cannot be modified.

C. Change Password. Press Enter key to Enter the menu, Enter the initial password is 000000,
press Enter to adjust PM2 to select a digit number, PM3 to select a 6-digit letter or digit, press Enter to
enter the confirmed 6-digit password, and press Enter to change the system password
Settings.

D. Lock With Password. Press Enter key to prompt you to Enter a 6-digit password. Press Enter to
complete the operation.

5.factory data reset

If the password is lost or otherwise, the user can restore the machine to its original factory state by
restoring the factory Settings.
Note: restoring factory Settings means that all saved parameters will be lost!
The specific operation is as follows: under the shutdown state of the processor, press and hold the panel
Enter+Back+Menu button at the same time, and then turn on the computer until the display screen shows
the following interface, and you can release the button, And the system restores factory Settings

~8~
Gigital Speaker Processor

Technical Parameters

Input: four - channel electronic balance

Impedance:＞10 k ohms
Maximum input level: +12dBu

Output: six - channel electronic balance

Impedance: ＜80 ohms
Maximum output level: +18dBu

Frequency response: ± 0.5dB 20Hz-20KHz

S/N: ＞100 dBA
THD + N: ＜0.005%
Intelligent fan accelerates temperature to control the inside of device.

Maximum delay of each input: 420.9984mS

Maximum delay of each output: 128.9984mS
Input gain: +12dB to -18dB, step interval 0.1dB
Output gain: +12dB ~ -18dB, step 0.1dB
Parametric equalizer: input 30 segments, output 7 segments

High pass (low cut) and low pass (high cut) filters
Frequency range: 20Hz ~ 20KHz, 1/36 octave
Filter slope: -6dB, -12dB, -18dB, -24dB, -36dB, -48dB.
Type selection: Butterworth, Linkwitz-Riley, Bessel 12dB Variable Q value.

Input Noise gate

Threshold value：-80dBu~-50dBu
Startup time：10ms ~ 1 . 0sec
Release time：1ms~1.0sec

Input compressor, output limiter

Threshold value : -14dB to 16dB, and the adjustment step is 0.2dB.
Ratio output value: 2:1~32:1, inflection point: 0%~100%
Startup time ranges from 0.1 to 3.0sec/ output (5.0sec).
Release time (5ms to 200ms/1ms to 900ms) Input/output channel.

Connector
Input: 3-pin XLR female socket
Output: 3-pin XLR male socket
Communication port: RS485 USB
Power supply: AC220V~240V @ 50/60Hz
Power consumption: ＜50 watts

~9~
 Digital Speaker Processor

Audio Connection

Through USB to connect computer and

proceed software adjustment

It can also be controlled by the

central control platform through
the RS485 connection line.

MIC input Music input

BALANCE BALANCE
1 2 3 4 5 6 7 9 10 11 12 13 14 OUT
MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC MIC

L R

LINE LINE LINE LINE LINE LINE LINE LINE LINE LINE LINE LINE
LINE RETURN

CUT LPF CUT LPF CUT LPF CUT LPF CUT LPF CUT LPF CUT LPF CUT LPF CUT LPF CUT LPF CUT LPF CUT LPF
CUT LPF
AUX OUT PHONES EFFECT

Control platform
GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN

HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH HIGH

MID MID MID MID MID MID MID MID MID MID MID MID MID

LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW LOW

AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX AUX

L R
EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT

PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN
AUX
PFL PFL PFL PFL PFL PFL PFL PFL PFL PFL PFL PFL PFL

MAIN L/R EFFECT

Power amplifier Power amplifier Power amplifier Power amplifier

Full-range speaker Full-range speaker Full-range speaker Subwoofer

~10~
c PROFESSIONAL AUDIO SYSTEM

DIGITAL SPEAKER PROCESSOR