Sysmac Studio
Software Selection Guide
INTEGRATED | INTELLIGENT | INTERACTIVE
Sysmac Studio Selection Guide
One Integrated Development Environment
Created to give you complete control over your automation system
Combining configuration, programming and monitoring in a single interface, Sysmac Studio is a unique
environment that integrates logic, motion and drives, robotics, safety, visualization, sensing and information
technologies in one project. This reduces the learning curve and the intra-operative software costs.
License options include the full-featured version, the controller-specific version, and a version specific to
other technologies.
One license to cover 90% of all application needs
90% Omron offers a simple process to purchase a Sysmac Studio license. In most cases,
one license can cover all your application needs, with only a one-time fee and no
maintenance contracts.
2
License Options
Sysmac Sysmac Sysmac Symac Sysmac Sysmac
Sysmac Studio
Studio Studio Studio Studio Studio Studio
Measurement
Standard Lite Vision Drive Safety NX
NX1P2 • •
NX102 • •
Logic
NJ1 • •
NJ3 •
NJ5 •
NX7 •
HMI NA5 • •
NX I/O
EtherCAT
Coupler
• •
I/O
NX I/O
EtherNet/IP
Coupler
• • •
FH • • •
Vision FHV7 • • •
FQM • • •
Safety
NX-SL3 • • • •
NX-SL5/CSG • • •
Motion
1S • • •
G5 • • •
Measurement ZW • • •
3
Sysmac Studio Selection Guide
Sysmac Studio Standard and Lite Editions
One Integrated Development Environment
Sysmac Studio Standard Edition
Compatible with all Sysmac Devices
Part Number # of Users License Delivery Method Included with Install:
SYSMAC-SE201L 1 Electronic • Sysmac Studio
• CX-Integrator
SYSMAC-SE203L 3 Electronic
• CX-Designer
SYSMAC-SE210L 10 Electronic • CX-Protocol
• Network Configurator
SYSMAC-SE230L 30 Electronic • CX-ConfiguratorFDT
• Adept Robot IP Address Setting Tool
SYSMAC-SE250L 50 Electronic • CX-Server
SYSMAC-SE2XXL Site Electronic • Communications Middleware
Sysmac Studio Lite Edition
Compatible with all Sysmac Devices except NJ3, NJ5, NX7
Full Capability of Sysmac Studio Limited to NX1, NJ1 Included with Install:
controllers for cost savings.
• Sysmac Studio
Part Number # of Users License Delivery Method • CX-Integrator
SYSMAC-LE201L 1 Electronic • CX-Designer
• CX-Protocol
SYSMAC-LE203L 3 Electronic • Network Configurator
• CX-ConfiguratorFDT
SYSMAC-LE210L 10 Electronic
• Adept Robot IP Address Setting Tool
• CX-Server
License required to upgrade from Lite to Standard
Part Number # of Users License Delivery Method
SYSMAC-LU501L 1 Electronic
SYSMAC-LU503L 3 Electronic
SYSMAC-LU510L 10 Electronic
4
System Requirements
The system requirements for Sysmac Studio Standard
and Sysmac Studio Lite are given in the following tables
OS CPU RAM Display
Windows 7 IBM AT or compatible with
XGA 1,024 x 768,
(32-bit) Minimum¹ Intel® Celeron® processor 540 2 GB
16 million colors
Windows 8 (1.8 Ghz)
(32-bit)
Windows 8.1 IBM AT or compatible with
(32-bit) 4 GB WXGA 1,280 x 800x
Recommended²,³ Intel® Core™ i5 M520 processor
Windows 10 min. 16 million colors
(2.4 GHz) or equivalent
(32-bit or 64-bit edition)
1. If you create a user program with a memory size that exceeds 20 MB, use the 64-bit edition of the operating system and 8 GB or more of RAM.
2. If the user program is large, we recommend that you use a 64-bit IBM AT or compatible with an Intel® Core™ i7 processor or better and 8 GB or
more of RAM.
3. If you use the Robot Additional Option and execute Vision and Robot integrated simulations, use a 64-bit IBM AT or compatible with an Intel®
Core™ i5 processor or better and 8 GB or more of RAM.
In addition, the following are also required
System Requirement Specification
Available hard disk space required for installation 4.6 GB min.
Communications port Ethernet or USB (USB 2.0)
Recommended Video Cards
The following are recommended to use 3D motion monitoring
Video memory 512 MB min.
One of the following video cards:
Video Card • NVIDIA GeForce 200 Series or better
• ATI Radeon HD5000 Series or better
5
Sysmac Studio Selection Guide
Limited Licenses
These licenses provide Sysmac Studio functionality for specific hardware only
Sysmac Studio Vision Edition
Compatible with only FH, FHV7, FQM (license allows users to configure Sysmac Vision Systems)
Part Number # of Users License Delivery Method
SYSMAC-VE001L 1 Electronic
Sysmac Studio Measurement Edition
Compatible with only ZW-series Displacement Sensors (license allows users to configure Displacement Sensor)
Part Number # of Users License Delivery Method
SYSMAC-ME001L 1 Electronic
Sysmac Studio NX/I-O Edition
Compatible with only EtherNet/IP Coupler (NX-EIC202) and NX-SL3
Part Number # of Users License Delivery Method
SYSMAC-NE001L 1 Electronic
Sysmac Studio Drive Edition
Compatible with only 1S and G5 Servos (license allows users to configure Sysmac Motion Drives)
Part Number # of Users License Delivery Method
SYSMAC-DE001L 1 Electronic
Sysmac Studio Safety Edition
Compatible with only NX-CSG, NX-SL5, and NX-SL3
Part Number # of Users License Delivery Method
SYSMAC-FE001L 1 Electronic
6
Add-On Licenses
These licenses provide additional functionality and are required in addition
to a Sysmac Studio License
Sysmac Studio Team Edition
The Team Edition implementation of Sysmac Studio incorporates a distributed version control system that
allows multiple co-developers to work on the same project.
Part Number # of Users License Delivery Method
SYSMAC-TA401L 1 Electronic
SYSMAC-TA403L 3 Electronic
SYSMAC-TA410L 10 Electronic
SYSMAC-TA430L 30 Electronic
SYSMAC-TA450L 50 Electronic
SYSMAC-TA4XXL site Electronic
AI Controller
This license is required to use the AI Controller and is bundled in when hardware is purchased.
Not available for purchase separately.
Part Number # of Users License Delivery Method
SYSMAC-AL0101L N/A Included with Hardware Purchase
NC Controller
The CNC Operator is the software that provides an operation interface for NC programming, debugging and
maintenance for CNC machines. One license for CNC Operator is included with the NC CPU unit.
Part Number # of Users License Delivery Method
SYSMAC-RTNC0001L 1 Dongle included with CPU Unit
CNC Operator Software Development Kit is an optional add on that provides an environment for customizing the
CNC Operator.
SYSMAC-RTNC0101D 1 Dongle included with CPU Unit
Robot and Vision Simulation
This license is required to enable the Vision and Robot Simulation Tool
Part Number # of Users License Delivery Method
SYSMAC-RA401L 1 Non Stock
3D Simulation
This license is required to use the 3D Simulation functionality available with 64 Bit version of Sysmac Studio
Part Number # of Users License Delivery Method
SYSMAC-SA401L-64 1 Electronic
SYSMAC-SA403L-64 3 Electronic
SYSMAC-SA410L-64 10 Electronic
SYSMAC-SA430L-64 30 Electronic
SYSMAC-SA450L-64 50 Electronic
SYSMAC-SA4XXL-64 Site Electronic
7
OMRON AUTOMATION AMERICAS HEADQUARTERS • Chicago, IL USA • 847.843.7900 • 800.556.6766 • automation.omron.com
OMRON CANADA, INC. • HEAD OFFICE OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • automation.omron.com São Paulo, SP, Brasil • 55 11 5171-8920 • automation.omron.com
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE OMRON ARGENTINA • SALES OFFICE
Ciudad de México • 52.55.5901.4300 • 01.800.386.6766 •
[email protected] Buenos Aires, Argentina • +54.11.4521.8630 • +54.11.4523.8483
[email protected]OMRON ELECTRONICS DE MEXICO • SALES OFFICE
San Pedro Garza García, N.L. • 81.12.53.7392 • 01.800.386.6766 •
[email protected] OTHER OMRON LATIN AMERICA SALES
+54.11.4521.8630 • +54.11.4523.8483 •
[email protected]OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Eugenio Garza Sada,León, Gto • 01.800.386.6766 •
[email protected] Authorized Distributor: Controllers & I/O
• Machine Automation Controllers (MAC) • Motion Controllers
• Programmable Logic Controllers (PLC) • Temperature Controllers • Remote I/O
Robotics
• Industrial Robots • Mobile Robots
Operator Interfaces
• Human Machine Interface (HMI)
Motion & Drives
• Machine Automation Controllers (MAC) • Motion Controllers • Servo Systems
• Frequency Inverters
Vision, Measurement & Identification
• Vision Sensors & Systems • Measurement Sensors • Auto Identification Systems
Sensing
• Photoelectric Sensors • Fiber-Optic Sensors • Proximity Sensors
• Rotary Encoders • Ultrasonic Sensors
Safety
• Safety Light Curtains • Safety Laser Scanners • Programmable Safety Systems
• Safety Mats and Edges • Safety Door Switches • Emergency Stop Devices
• Safety Switches & Operator Controls • Safety Monitoring/Force-guided Relays
Control Components
• Power Supplies • Timers • Counters • Programmable Relays
• Digital Panel Meters • Monitoring Products
Switches & Relays
• Limit Switches • Pushbutton Switches • Electromechanical Relays
• Solid State Relays
Software
• Programming & Configuration • Runtime
PC-388 Note: Specifications are subject to change. © 2020 Omron. All Rights Reserved. Printed in U.S.A.
Printed on recycled paper.
