TCP IP Primer Plus

TCP/IP Primer Plus
Heather Osterloh
201 West 103rd St., Indianapolis, Indiana, 46290 USA
TCP/IP Primer Plus

Copyright 2002 by Sams Publishing All rights reserved. No part of this book shall be reproduced, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without written permission from the publisher. No patent liability is assumed with respect to the use of the information contained herein. Although every precaution has been taken in the preparation of this book, the publisher and author assume no responsibility for errors or omissions. Nor is any liability assumed for damages resulting from the use of the information contained herein. International Standard Book Number: 0-672-32208-0 Library of Congress Catalog Card Number: 2001093492 Printed in the United States of America First Printing: September 2001 04 03 02 01 4 3 2 1
ASSOCIATE PUBLISHER
Jeff Koch
ACQUISITIONS EDITOR
Kathryn Purdum
DEVELOPMENT EDITOR
Mark Renfrow
MANAGING EDITOR
Matt Purcell
PROJECT EDITOR
Christina Smith Emily Morgan

COPY EDITOR
Rachel Lopez
INDEXER
Trademarks
All terms mentioned in this book that are known to be trademarks or service marks have been appropriately capitalized. Sams Publishing cannot attest to the accuracy of this information. Use of a term in this book should not be regarded as affecting the validity of any trademark or service mark.
Sandra Henselmeier
PROOFREADER
Kelly Thompson Plan-it Publishing

TECHNICAL EDITOR
Michelle Truman
Warning and Disclaimer

Every effort has been made to make this book as complete and as accurate as possible, but no warranty or fitness is implied. The information provided is on an as is basis. The author and the publisher shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the information contained in this book.
TEAM COORDINATOR
Vicki Harding
INTERIOR DESIGNER
Gary Adair
COVER DESIGNER
Alan Clements
PAGE LAYOUT
Michelle Mitchell
CONTENTS AT A GLANCE
INTRODUTION
CHAPTER 1 CHAPTER 2 CHAPTER 3 CHAPTER 4 CHAPTER 5 CHAPTER 6 CHAPTER 7 CHAPTER 8 CHAPTER 9 CHAPTER 10 CHAPTER 11 CHAPTER 12 CHAPTER 13 CHAPTER 14 CHAPTER 15 CHAPTER 16 CHAPTER 17 CHAPTER 18 APPENDIX A APPENDIX B APPENDIX C APPENDIX D APPENDIX E
1 Overview of Industry Models and Standards . . . . . . . . . . . . . . . . . .3 IP Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Network Layer/Internet Protocols . . . . . . . . . . . . . . . . . . . . . . . . .61 Address Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 IP Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 Routing Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 Transport/Host-to-Host Layer . . . . . . . . . . . . . . . . . . . . . . . . . . .203 Transmission Control Protocol (TCP) . . . . . . . . . . . . . . . . . . . . .211 User Datagram Protocol (UDP) . . . . . . . . . . . . . . . . . . . . . . . . . .241 Upper-layer Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257 File Transfer Protocol (FTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .269 Simple Mail Transfer Protocol (SMTP) . . . . . . . . . . . . . . . . . . . . .287 Name Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .299 HyperText Transfer Protocol (HTTP) . . . . . . . . . . . . . . . . . . . . . .321 Trivial File Transfer Protocol (TFTP) . . . . . . . . . . . . . . . . . . . . . .335 Simple Network Management Protocol (SNMP) . . . . . . . . . . . . .345 Open Network Computing Protocols . . . . . . . . . . . . . . . . . . . . .353 Request for Comments (RFCs) . . . . . . . . . . . . . . . . . . . . . . . . . .371 Abbreviations and Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . .423 TCP/UDP Port Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .431 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433 Answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .465 481
INDEX
TABLE OF CONTENTS
INTRODUCTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
C H A P T E R 1 : Overview of Industry Models and Standards
. . . . . . . . . . . . . . . . . .3 Overview of the OSI Reference Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Overview of the Department of Defense Model . . . . . . . . . . . . . . . . . . . . . . . . .5 Benefits of the OSIs Layered Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Layer Functions Clarified . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Well-defined Framework for Vendors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Reduced Networking Complexity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Promotes Specialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 General Description of OSI Layers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Application Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Presentation Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Session Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Transport Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Network Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Data Link Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Physical Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Data Link Architecture and Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Ethernet and IEEE 802.3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Slow Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Fast Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Gigabit Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Token-Ring and IEEE 802.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 FDDI and ANSI X3T9.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Wide Area Networking (WAN) Technologies . . . . . . . . . . . . . . . . . . . . . . . . .25 WAN Encapsulation Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Request For Comments (RFCs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Internet Versus intranet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Groups Responsible for Internet Technology . . . . . . . . . . . . . . . . . . . . . . . . .31 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Understanding Binary to Decimal Conversion . . . . . . . . . . . . . . . . . . . . . . . .33 IP Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Address Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Network and Subnet Masks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Subnetting and Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Network Address Translation (NAT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
C H A P T E R 2 : IP Addressing
vi
TCP/IP PRIMER PLUS
Static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

C H A P T E R 3 : Network Layer/Internet Protocols . . . . . . . . . . . . . . . . . . . . . . . . . .61
IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 IP Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 ICMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 ICMP Header and Message Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 Checksum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 ICMP Message Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Ping: Echo Request and ReplyTypes 8 and 0 . . . . . . . . . . . . . . . . . . . . .77 Destination UnreachableType 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 Source QuenchType 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 RedirectType 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Router Advertisement and SolicitationTypes 9 and 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Time ExceededType 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Parameter ProblemType 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 Timestamp Request and ReplyTypes 13 and 14 . . . . . . . . . . . . . . . . . . .86 Information Request and ReplyTypes 15 and 16 . . . . . . . . . . . . . . . . . . .86 Address Mask Request and ReplyTypes 17 and 18 . . . . . . . . . . . . . . . . .86 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
C H A P T E R 4 : Address Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 ARP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 ARP Cache Mechanisms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 Proxy ARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Proxy ARP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 ARP Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 Hardware Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Protocol Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 Length of Hardware Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 Length of Protocol Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 Opcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Senders Hardware Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Senders Protocol Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Target Hardware Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Target Protocol Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
CONTENTS
vii
RARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 RARP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 ARP Versus RARP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 Disadvantages of RARP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 RARP Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Protocol Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Length of Hardware Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Length of Protocol Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Opcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Senders Hardware Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Senders Protocol Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Target Hardware Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Target Protocol Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 BOOTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 BOOTP header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 BOOTP Request and Reply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 DHCP (Dynamic Host Configuration Protocol) . . . . . . . . . . . . . . . . . . . . . . .110 Allocating Configuration Information . . . . . . . . . . . . . . . . . . . . . . . . . . .111 DHCP Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 DHCP Message Exchanges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 DHCP Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
C H A P T E R 5 : IP Routing
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 IP Routing Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 Directly Connected Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 Static Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 Default Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 Dynamic Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128 Routing Protocols and Best Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Distance Vector Routing Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Link State Routing Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 Hybrid Routing Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 Introduction to Routing Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 RIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 RIPv1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139 The RIPv1 Header and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
C H A P T E R 6 : Routing Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
viii
TCP/IP PRIMER PLUS
Disadvantages of RIPv1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 RIP Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 RIP and Demand Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148 RIPv2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 OSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152 OSPF Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 OSPF Databases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155 OSPF Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156 The LSA Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160 OSPF Router States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162 OSPF Router Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167 OSPF Operation Over Various Data Link Architectures . . . . . . . . . . . . . .167 Area Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 Standard OSPF Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173 Additional Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 IGRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181 IGRP Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182 EIGRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184 EIGRP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184 EIGRP Packet Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 BGP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 IGPs Versus EGPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188 BGP Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .189 BGP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190 The BGP Header and Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .191 Path Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 BGPv3 Versus BGPv4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200
C H A P T E R 7 : Transport/Host-to-Host Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . .203
Transport Layer Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 Connection-Oriented Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204 Connectionless Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206 Connectionless Versus Connection-oriented Protocols . . . . . . . . . . . . . . .206 Ports and Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
C H A P T E R 8 : Transmission Control Protocol (TCP) . . . . . . . . . . . . . . . . . . . . . .211
Introduction to TCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211 TCP Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212 Source Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213 Destination Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213
CONTENTS
ix
Sequence Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214 Acknowledgement Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214 Data Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 Reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 Control Flags6 Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 Checksum2 Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 Urgent Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 TCP OptionsVariable Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217 Fundamentals of TCP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .218 Connection Setup and Teardown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .219 Multiplexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .219 Data Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220 Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 Precedence and Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .222 Connection-oriented Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 Session Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 Session Teardown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 Sequencing and Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 Keepalives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .234 Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .234 TCP Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .237 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .238 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .238
C H A P T E R 9 : User Datagram Protocol (UDP) . . . . . . . . . . . . . . . . . . . . . . . . . . .241
UDP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .242 UDP Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .243 UDP Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .244 UDP Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .244 Source Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .245 Destination Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .245 Length Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .245 Checksum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .246 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247
C H A P T E R 1 0 : Upper-layer Protocols
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 Introduction to Upper-layer Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 Application Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251 World Wide Web and HTTP (Hypertext Transfer Protocol) . . . . . . . . . . .251 E-mail and SMTP (Simple Mail Transfer Protocol) . . . . . . . . . . . . . . . . . .252
TCP/IP PRIMER PLUS
Telnet (Telecommunications Network) . . . . . . . . . . . . . . . . . . . . . . . . . . .252 File Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253 Presentation Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253 Session Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .254 NetBIOS (Network Basic Input Output System) . . . . . . . . . . . . . . . . . . . .254 NFS (Network File System) and ONC Protocols . . . . . . . . . . . . . . . . . . .255 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255
C H A P T E R 1 1 : Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257
Remote Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257 Basic Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259 Network Virtual Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259 Telnet Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 Telnet Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .264 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .268
C H A P T E R 1 2 : File Transfer Protocol (FTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .269
Introduction to File Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269 FTP Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .270 Data Representation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .274 FTP Data Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275 FTP Data Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277 FTP Transmission Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .278 FTP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .278 FTP Replies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .281 FTP Operation and Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .282 Anonymous FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .285
C H A P T E R 1 3 : Simple Mail Transfer Protocol (SMTP) . . . . . . . . . . . . . . . . . . . .287
X.400 Naming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .289 Message Transfer Agents (MTAs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .290 SMTP Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .291 SMTP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .292 SMTP Replies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .293 MIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .295 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .296 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .297
CONTENTS
xi
C H A P T E R 1 4 : Name Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .299
Why Do We Need Name Resolution? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .299 Namespace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300 DNS Delegation of Authority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .301 Internet Domain Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .304 Queries and Mappings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .305 Caching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .305 Domain Server Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306 Identifier (ID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306 QR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306 Opcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306 Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .307 Rcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .307 Answers and Questions Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .309 Domain Name Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .310 DNS Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .310 NetBios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .313 NetBIOS Over TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .314 Node Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .315 WINS (Windows Internet Name Server) . . . . . . . . . . . . . . . . . . . . . . . . .317 NetBIOS Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .317 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .319 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .319
C H A P T E R 1 5 : Hypertext Transfer Protocol (HTTP) . . . . . . . . . . . . . . . . . . . . . .321
HTTP and the World Wide Web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .321 HTTP Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .322 HTTP Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .322 HTTP Sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324 HTTP Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325 Generic Start Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .326 General Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .326 Message Headers (Request, Response, or Entity) . . . . . . . . . . . . . . . . . . .328 Empty line (CRLF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .330 Message Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .330 HTTP Response Messages, Status, and Error Codes . . . . . . . . . . . . . . . . . . .330 HTTP Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .332 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .333 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .334
xii
TCP/IP PRIMER PLUS
C H A P T E R 1 6 : Trivial File Transfer Protocol (TFTP)
. . . . . . . . . . . . . . . . . . . . .335 Introduction to File Transfer Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . .335 TFTP Packet Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .336 RRQ and WRQ Packets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .337 Data Packets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .338 ACK Packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .338 Error Packets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .339 TFTP Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .340 TFTP Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .342 OACK Packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .343 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .343 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .343
C H A P T E R 1 7 : SNMP (Simple Network Management Protocol) . . . . . . . . . . . . .345
Introduction to Network Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . .345 SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .346 SNMP Managers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .347 SNMP Agents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .347 Proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .348 SNMP Message Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .348 Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .349 Community Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .349 SNMP Protocol Data Units (PDUs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .350 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .351 Review Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .352
C H A P T E R 1 8 : Open Network Computing Protocols . . . . . . . . . . . . . . . . . . . . .353
Introduction to Open Network Computing Protocols . . . . . . . . . . . . . . . . . .353 NFS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .354 NFS Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .356 NFS Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .357 NFS Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .358 XDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .359 RPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .360 Call Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .361 Reply Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .366 NFS Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .367 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .369 Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .369
A P P E N D I X A : RFCs Organized by Chapter
. . . . . . . . . . . . . . . . . . . . . . . . . . .371 Chapter 1: Overview of Industry Models and Standards . . . . . . . . . . . . . . . .371 Chapter 2: IP Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .371
CONTENTS
xiii
Chapter 3: Network Layer/Internet Protocols . . . . . . . . . . . . . . . . . . . . . . . .371 Chapter 4: Address Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .374 Chapter 5: IP Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .375 Chapter 6: Routing Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .382 Chapter 7: Transport/Host-to-Host Layer . . . . . . . . . . . . . . . . . . . . . . . . . . .389 Chapter 8: Transmission Control Protocol (TCP) . . . . . . . . . . . . . . . . . . . . .389 Chapter 9: User Datagram Protocol (UDP) . . . . . . . . . . . . . . . . . . . . . . . . . .391 Chapter 11: Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .391 Chapter 12: File Transfer Protocol (FTP) . . . . . . . . . . . . . . . . . . . . . . . . . . .396 Chapter 13: Simple Mail Transfer Protocol (SMTP) . . . . . . . . . . . . . . . . . . . .398 Chapter 14: Name Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .410 Chapter 15: Hypertext Transfer Protocol (HTTP) . . . . . . . . . . . . . . . . . . . . .414 Chapter 16: Trivial File Transfer Protocol (TFTP) . . . . . . . . . . . . . . . . . . . . .415 Chapter 17: Simple Network Management Protocol (SNMP) . . . . . . . . . . . .416 Chapter 18: Open Network Computing Protocols . . . . . . . . . . . . . . . . . . . .421
A P P E N D I X B : Abbreviations and Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . .423
A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423 B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423 C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .424 D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .424 E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .425 F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .425 GH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .425 I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .426 JL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .426 M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .427 N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .427 O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .428 P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .428 Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .428 R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .429 S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .429 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .430 U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .430 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .430 W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .430 XZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .430
A P P E N D I X C : TCP/UDP Port Numbers
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .431
A P P E N D I X D : Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433
Numeric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .434
xiv
TCP/IP PRIMER PLUS
B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .435 C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .437 D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .439 E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .442 F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .443 G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .445 H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .445 I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .446 JK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .447 L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .447 M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .448 N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450 O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .451 Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454 R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .454 S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .456 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .460 U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .462 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .462 W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .463 XY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .464 Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .464
A P P E N D I X E : Answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .465
Chapter 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .465 Chapter 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .465 Chapter 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .466 Chapter 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467 Chapter 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .467 Chapter 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .468 Chapter 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .471 Chapter 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .471 Chapter 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .472 Chapter 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .473 Chapter 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .473 Chapter 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .474 Chapter 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .475 Chapter 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .476 Chapter 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .477 Chapter 16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .477
CONTENTS
xv
Chapter 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .478 Chapter 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .479

I N D E X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .481
ABOUT THE AUTHOR

Heather Osterloh has earned industry recognition as a Cisco Certified Network Associate (CCNA), Cisco Certified Network Professional (CCNP), Cisco Certified Design Associate (CCDA), Cisco Certified Design Professional (CCDP), Network Associate Sniffer trainer, Certified Network Expert (CNX) for Ethernet and Token Ring, Novell CNI/ECNE, Microsoft Certified Systems Engineer (MCSE) and Microsoft Certified Trainer (MCT). She also holds her Cisco Certified Internetworking Expert (CCIE), written portion and is currently waiting to take the practical lab exam. Having spent the last 15 years training and consulting worldwide, Heather is an acknowledged leader in the networking industry. Author of one book, CCNA 2.0 Prep Kit 640-507 Routing and Switching, and of several popular Microsoft, Cisco, and Novell video series geared towards the busy professional, Heather continues to produce material that helps educate people about the world of networking. Heather also has lectured at the University of California, Berkeley; NetuCons NetWare User Conference in San Jose; and the University of Puerto Rico; and was president of IT Academy, LLC for three years. Heather lives in Northern California with her husband Kirk and her dogs, Cocoa and Kato.
DEDICATION
In memory of my grandfather and grandmother, Anthony and Nina.
ACKNOWLEDGMENTS
For a project of this magnitude, there are many people to thank: First, Sams Publishing for giving me this opportunity to write this book. And all the people at Sams that made this book happen, especially William Brown, Mark Renfrow, Christina Smith, Rachel Bell, Kitty Jarrett, and Michelle Truman, all of whom went beyond the call of duty to support me. My amazing team, Jason Burita and Christine Sepiol, who managed to keep me focused and polished my chicken scratches into manageable text. The team at IT Academy, Heidi, Beverly, and Brycewithout their additional support and sacrifices, this project would not have been possible. Laura Chappell, who first inspired me by introducing me to the world of network certification. To all my students, who continue to challenge me in class and inspire me to write the best possible book. To my parents, Rita and Karl, who have always been supportive and behind me 100 percent. My dogs, Cocoa and Kato, who jumped up on my laptop while I wrote, forcing me to take a much needed break and providing a little comic relief. And most important, my husband Kirk, for having patience with me during the panic attacks, stressful deadlines, and lack of sleep that went into completing this book. His constant support endears my heart and makes me realize that I can accomplish anything. Thanks honey.
TELL US WHAT YOU THINK!

As the reader of this book, you are our most important critic and commentator. We value your opinion and want to know what were doing right, what we could do better, what areas youd like to see us publish in, and any other words of wisdom youre willing to pass our way. As an Associate Publisher for Sams Publishing, I welcome your comments. You can e-mail or write me directly to let me know what you did or didnt like about this bookas well as what we can do to make our books stronger. Please note that I cannot help you with technical problems related to the topic of this book, and that due to the high volume of mail I receive, I might not be able to reply to every message. When you write, please be sure to include this books title and authors name, as well as your name and phone or fax number. I will carefully review your comments and share them with the author and editors who worked on the book.
E-mail: Mail:
[email protected]
Jeff Koch Associate Publisher Sams Publishing 201 West 103rd Street Indianapolis, IN 46290 USA
INTRODUCTION
Franz Kafka once wrote, A book must be the axe for the frozen sea inside of us. This book will help you break through the ice, enabling you to understand the world of TCP/IP without being as obscure as a Kafka quote. After all, it is not rocket sciencejust a few routers, keyboards, PCs and protocols that make everything workor in some cases, not work. In this book we give you enough information to understand what works and what doesnt, and hopefully remove the mystery from networking. This book unfolds in a logical order, starting with background on the OSI and DoD models, focusing on the Data Link and Physical layers. The book then proceeds up the OSI model and discusses the various TCP/IP protocols that reside at those layers. At the end you should have a solid foundational knowledge of all the major protocols that reside in the TCP/IP suite. However, you also can use the book in a nonlinear manner, because it references chapters where other protocols or ideas are covered. Throughout the book, we have tried to involve the reader as much as possible. Often books discuss TCP/IP as theory or as if no human is involved in internetworking. As you are aware, this is simply not the case. It is you who configures the router or types an e-mail to your coworker. It is for this reason that we often use you, the user and reader, in an active manner; we feel involving you helps you learn. We also have included many screen shots. In the text, we will refer to these screen shots as a screen capture as seen through a Sniffer or Sniffer Network Analyzer. A Sniffer screen shot merely captures frames (network traffic) in a way that is readable and understandable to you. In short, a Sniffer is a networking troubleshooting tool. However, for this books purposes, it provides us with a window to what occurs in the internetworkwhat a protocol is doing. Often the Sniffer screen shots will show a particular frame; this frame will be highlighted. The output, or what is contained below the frame portion of the screen capture, details the header information. From this header information, you can gather various information, from IP addresses, to Opcodes, to what protocol it is. In addition, these screen shots often will be paired with clinical diagrams of headers. The clinical diagrams portray the protocols in a way that is defined by an RFC (Request for Comment); however, a screen shot details a protocol in a more realistic manner. We feel that showing both gives you broader, more realistic hands-on experience. In this book, you also will see RFC references (and then a number; for example, RFC 1583). RFCs are generally dry, factual documentation and specifications of TCP/IP protocols. Rather than merely repeating what an RFC says, we reference it and then use a more exciting and accessible language to describe it. However, we have provided you with a list of RFCs by chapter in Appendix A if you want to research the various RFCs. RFCs can be found free on the Web; the full details are contained within this book.
TCP/IP PRIMER PLUS
Hopefully, we have given you enough background to aid you in reading this book. However, if you have any additional questions regarding the book, please feel free to contact Heather Osterloh by e-mail at [email protected]. She will gladly answer any of your questions as promptly as possible.
CHAPTER 1
OVERVIEW OF INDUSTRY MODELS AND STANDARDS
You will learn about the following in this chapter:

The OSI model The DoD model Seven-layer Architecture Network Architecture and Topologies Wide Area Network Technologies Request For Comments
Overview of the OSI Reference Model

In the early days of networking only proprietary systems and protocols existed. Operating systems developed by large companies, such as IBMs SNA and Digital Equipment Corporations DECNet, included proprietary protocol suites. These operating systems and their corresponding protocols primarily facilitated mini- and mainframe network communication; however, these companies made no provisions for interconnection or to allow for communication with outside systems. When IBM developed SNA and Digital Equipment Corporation developed DECNet, no one anticipated the prevalence of the mixed computing environments that exist today; thus only systems using compatible protocols and operating systems could communicate with each other and exchange data. As you can imagine, these different proprietary systems had a hard time communicating with each other, if they were able to at all. It soon became necessary to create some type of protocol translation to enable companies to communicate and share information with one another. The Department of Defense (DoD) developed an intercommunication model in the early 1970s, which became the source model for the TCP/IP protocol suite. However, this model has been largely replaced with the OSI Reference Model released in the early 1980s. The OSI Reference Model consists of a seven-layer architecture that defines the different networking functions that occur at each layer (see Figure 1.1). Later in this chapter you will find a further discussion of the DoD model and how it maps to the OSI model. We refer to both models throughout the book when describing the purpose and function of each protocol within the TCP/IP suite.
TCP/IP PRIMER PLUS
FIGURE 1.1
OSI Model and Functions

Application Presentation Session Transport Network Data Link Physical
Provides services to User Applications
The OSI Reference Model defines the seven layers and their functions.
Data translation, conversion, encryption, decryption, compression
Session management and dialog control
End-to-end communication between programs/processes
Logical addressing and routing
Frame transmission and reception
Signal encoding, media and connectors
The OSI Reference Model enables both similar and dissimilar systems to communicate seamlessly by providing an architectural framework for vendors and manufacturers to follow when designing their hardware, protocols, and operating system environments. This provides engineers and developers with standard specifications for system intercommunication. It also provides for the use of different protocols in different network architectures and lower-layered media types. Although seamless communication is not always achieved, the OSI Reference Model considers it the primary goal. Before the OSI model, the protocols in existence did not lend themselves easily to interconnectivity. In most cases retrofitting these protocols would be infeasible. As such, most protocols and hardware currently implemented by vendors and manufacturers conform to the guidelines of the OSI model. The smooth, swift exchange of data and seamless interconnectivity required in todays mixed computing environments depends on manufacturers and vendors adhering to a standardized reference model. The OSI model is a conceptual framework. It consists of a series of standards defining what should happen and how to package data so it can go out on the wire to a remote host. The logical layers of the model do not specifically define what needs to be performed at each layer; they simply define which functions reside at each respective layer. How the functionality occurs at each layer depends on the vendor or the manufacturer that creates or implements the hardware or the protocols. Individual manufacturers have the liberty of interpreting and deciding how closely they wish to adhere to the specifications for a given layer. The end results do not always create seamless compatibility between dissimilar devices; however, this framework and model provides the best resource available for this compatibility. The OSI model consists of the following seven (from top to bottom):
Chapter 1 OVERVIEW OF INDUSTRY MODELS AND STANDARDS
Application Presentation Session Transport Network Data Link Physical Overall, each layer has distinct functions that must occur within it to prepare data to go out on the wire to communicate with a remote station. The vendor can determine the specifics within the general functions; that is, the manufacturer or developer defines how those specifics work, so vendors need to concern themselves with only their part of the puzzle. As long as an organization or vendor follows the guidelines laid out by the ISO for a developers particular layer, the result is a product that can easily integrate with other products that follow the model. Keep in mind that you use the OSI only when you package data for transmission to connect to a remote host, similar or dissimilar (in other words, one using the same protocols and same operating system that you areor are not). The OSI Reference Model is not used when accessing data locally on a system. For example, to access file and print services, you would simply access as usual a local computers hard drive and open a local application. In a situation such as this, no user intervention is required to access the data. However, if you want to perform that same function on a remote host you must somehow send a message to the other device to access files or a printer, and have that device respond to you by transferring the data. To redirect the request of accessing a file or print services, you need a redirector. The redirector redirects this request to the remote host for processing. The remote host prepares the request for transmission across the internetwork by adding header and control information so the destination knows what to do with the data and how to respond.
Overview of the Department of Defense Model

The history of the DoD model began long before the OSI model, which has since superseded it. Beginning in 1973 the Department of Defense Advanced Research Projects Agency (DARPA) began a program to formulate technologies that could interlink various kinds of packet networks. This research was called the Internetting Project and, as you might surmise from the name, resulted in todays Internet. The model developed by DARPA as an initial standard by which the core Internet protocols would conform became known as the DoD model. This four-layer model consists of the following (from top to bottom): The Process layer The Host-to-host layer
TCP/IP PRIMER PLUS
The Internet layer The Network Access layer As shown in Figure 1.2, the DoD model maps roughly to the OSI model from top to bottom.
FIGURE 1.2 DOD Model
Process/ Application
The DoD model consists of four distinct layers.
Host-to-Host Internet
Network Access
Benefits of the OSIs Layered Design

The layered design of the OSI Reference Model provides benefits for manufacturers and software developers, and for those who offer support and troubleshooting, such as network engineers. The OSI models benefits can be broken down as follows: Makes general functions of each layer clear. Provides a well-defined framework for vendors to use in writing applications and developing hardware. Reduces complexity of networking by compartmentalizing model functions. Promotes interoperability between dissimilar networks and protocols. Simplifies troubleshooting by reducing the focus for locating network complications. Accelerates evolution in the industry by facilitating specialization.
Layer Functions Clarified

By narrowing the scope of a layers responsibility, the OSI model eases the development and support burdens that manufacturers and network engineers address in their work. Additionally, the minimized responsibility of each layer eliminates the need to reinvent the boundaries of a product or protocol for a desired use. By having the layers clarified, vendors can develop products that work specifically for one layer; not seven. This enables them to specialize in certain areas and reduces the complexity of the network.
Well-defined Framework for Vendors

Vendors can write their specifications to one layer or multiple layers. A layered approach removes much of the complexity and allows vendors to focus on and specialize in only their particular layer of the OSI model. This also makes for better interoperability between systems and creates an open environment that allows multiple protocols to coexist. For example, a vendor that creates a Network Interface Card (NIC) can simply work with the Data Link layer of the OSI model. The modular design of the OSI enables vendors to produce specialized products. Because they dont need to address all functions from top to bottom they can focus on a particular layer and function of the OSI model. This makes it easier for vendors to write and release hardware or software. Additionally, despite the variation among vendors in adherence to each layers conceptual guidelines, the very existence of a standardized model increases both the current level of interoperability between systems and the likelihood that future protocols and products will coexist harmoniously on the same network.
Reduced Networking Complexity

The layered approach also allows the network engineer to apply a divide-and-conquer approach to troubleshooting. Once you know what should happen at each layer, you can identify which function does not work properly based on which layer is not performing its functions. The protocol or piece of hardware should function according to the specifications defined at that layer. Perhaps more important, the model offers seven smaller pieces to work with rather than forcing us to focus on the whole structure to locate problems. If a particular layer does not function properly you can use that model to isolate and compartmentalize the problem, which makes troubleshooting much easier. Overall, network operations function as simpler pieces rather than a single, more complicated entity.
Promotes Specialization
Finally, the use of a widely accepted, industry-wide set of guidelines for networking inspires even faster and more reliable programs and protocols. Knowing they can compete at any layer of the OSI Reference Model to improve on the specifications and performance, vendors push efficiency to the utmost limits. When vendors can focus on meeting the specific standards of only one layer, they are able to specialize in manufacturing products that meet the specific needs of the consumer; for example, a router (Layer 3) for the small office or home office.
General Description of OSI Layers

When you get ready to send data (this could mean anything from an e-mail message to a request to read a file from a remote host), that request needs to be packaged and redirected. The sending system must follow these steps, which are based on the specific functions of the OSI Reference Model:
TCP/IP PRIMER PLUS
1. Apply addressing to it 2. Associate protocols with it 3. Modulate it 4. Send it out on the wire When a system prepares data to be sent out on the wire, a redirector first captures the message, puts its header and control information on it, and sends it down to the next layer. Lower layers in the OSI model provide upper-layer support services. These can include reliable transport services, routing services, and addressing services. The message could be as simple as Hi from one user to another; these services still apply. Each layer in the OSI model helps provide header and control information so that a peer layer in the remote host can remove that header and control information and know what to do with it. Each layer has a distinct role in preparing data to be sent out on the wire to communicate with a peer remote host (see Figure 1.3). All of the steps inherent to these roles appear transparent to the user.
FIGURE 1.3 Layers Operate as Peers
Data AH PH SH TH NH DH NH TH TH SH SH SH PH PH PH PH AH AH AH AH AH Data Data Data Data Data Data DT
Each layer of the OSI model adds header and control information used by the corresponding layer at the receiving host.
Bits
When the computer passes data from one layer to the next, each layer adds header or control information to it as the data makes its way down to the Physical layer and the actual physical media (such as the wire or network cable). Each layer simply treats everything handed down as generic upper-layer data. This process is similar to an envelope being placed inside another envelope at each layer. For example, the Application layer provides header and control information to the peer Application layer at the remote host location. It then passes this header and control information, along with the data down the Presentation layer. The Presentation layer reads the
upper layers information as data. The Presentation layer disregards both the header and control information, and the data of the upper (Application) layer. The Presentation layer adds header and control information for the peer Presentation level at the remote host. In other words, each lower layer (in this case the Presentation layer) ignores the upper layers control and header information or data. It views it only as data, which it disregards. Each layer only uses its peer layers control and header information and data at the remote host. Each subsequent layer adds its own header and control information and sends the data down to the next level. Once the data reaches the Data Link level, the system runs an algorithm called a cyclical redundancy check (CRC) or a frame check sequence (FCS). It then adds the CRC as a trailer to the end of the information to guarantee that the bits being sent match the bits the end host receives. The term frame refers to the logical grouping of information that data undergoes at the Data Link layer. From there the data goes out on the wire as electrical or light signals1s and 0sand the intended remote host receives the data (see Figure 1.4).
FIGURE 1.4 Headers and Trailers
The receiving host removes headers and trailers before sending it up to the next layer.
Application Presentation Session Transport Network Datalink Physical
H1 H2 H3 H4 H5 H6
Messages Messages Messages Segments Datagrams or Packets Frames Bits 1 0 1 0 1 0 s CRC
Upon reception, this process is reversed. Each layer removes its header information and passes it up to the next layer, exposing that layers header and control information and data until it arrives at the Application layer, which strips off its own header and control information and passes the data up. This happens with every single frame that goes out on the wire. Each layer must attach header and control information so the peer layer can identify the upper layer that should receive it next.
Application Layer
The top layer of the OSI model can confuse people because they think it refers to user applications such as Word, Excel, PowerPoint, and so on. The Application layer does not refer to the software applications themselves, but rather a window that enables you to provide data access from one application to another across a network, and a window to the OSI Reference Model to prepare your data to be packaged and sent out on the wire.
10
TCP/IP PRIMER PLUS
The Application layer enables user applications to send data across the network. It simply affords access to the lower layers, or provides a window to the OSI model. Remember the Application layers job is to provide an interface to your protocol stack. Unlike the other OSI layers, this layer does not provide services to any of those other layers; rather it provides access for Application layer services only. Some of the Application layer services include: Applications with network and internetwork services File and print services E-mail Web access and HTTP Telnet access on a remote host File Transfer Protocol (FTP) We will discuss all of the preceding processes and more within this book.
Presentation Layer
The Presentation layer provides a common data format across different platforms. It is responsible for the following services: Data conversion and translation Compression/decompression Encryption/decryption An example of a true Presentation layer protocol is eXternal Data Representation (XDR). Sun MicroSystems uses this protocol in its client/server-based Network File System (NFS) implementation. NFS uses XDR to provide platform independence. XDR actually is incorporated into the programming code. We will discuss NFS and XDR in Chapter 18, Open Network Computing Protocols.
Session Layer
The Session layer manages and sets up sessions. A session consists of a dialog between Presentation layers on two or more systems. This layer also handles the requests for different services between systems and manages the responses to those requests between systems. It also controls the dialog between two applications on different hosts and manages data streams. The efficiency of dialog control between hosts in the Session layer depends on whether the communication mode is half-duplex or full-duplex. In a half-duplex configuration, only one device can communicate or transmit at a time while all others wait in standby mode for their turns. Each side must wait until the other process has finished sending and then respond with a separate acknowledgement. A full-duplex communication can send and receive at the
11
same time; therefore it is more efficient than half-duplex communication. Full duplexing accomplishes its efficiency by piggybacking, or including data within the same frame. An example of a Session layer protocol that you might know is the Network Basic Input Output System (NetBIOS). NetBIOS sets up a session between two Windows NT or Windows 95 machines. NetBIOS, a true Session layer protocol used by Microsoft, provides name services and session management between two devices using simple naming. The Session layer also includes Remote Procedure Call (RPC), developed by Sun, which allows clients to make requests for remote execution. The requests are sent to a remote host for processing and a response, which enables communication between two hosts across a network. NFS uses RPC to send calls and get responses at the session layer, and uses XDR at the presentation layer.
Transport Layer
The Transport layer generally is thought to provide guaranteed reliable delivery of data only between two communicating processes or programs running on remote hosts. However, this holds true only if the vendor decides to implement Transmission Control Protocol (TCP) rather than its less-reliable counterpart User Datagram Protocol (UDP). We will discuss TCP in Chapter 8, Transmission Control Protocol (TCP) and UDP in Chapter 9, User Datagram Protocol (UDP). The Transport layer does the following: Controls end-to-end communication between two processes running on different hosts. Provides connection-oriented or connectionless services to upper layers. Uses client- and server-port addresses to identify processes running within a host. Segments data for upper-layer applications. The Transport layer has the task of identifying which processes are communicating on each host and providing either connection-oriented services and reliable transport, or speed of delivery. It manages the data flow and deals with flow control if its a connection-oriented session. Both Transmission Control Protocol (TCP) and User Datagram Protocol (UDP) reside at the Transport layer. The Transport layer has the task of segmenting the data (messages) handed down by upperlayer applications. It handles addressing with ports, also referred to as sockets, addresses that identify which upper-layer program or process is communicating on a particular device. To govern the tracking and management of various segments, the Transport layer uses port numbers for each application.
Socket Pairing
When you have end-to-end communication between hosts that involves source and destination IP addresses and ports (also called sockets), the industry refers to this as a socket pair.
12
TCP/IP PRIMER PLUS
The Transport layer can provide both connection-oriented and connectionless service to an upper-layer protocol. However, whether connection-oriented or connectionless, the Transport layer deals with ports or process addresses. Client-based and server-based addresses such as TCP or UDP ports are used to identify the process that is running within a host. We will discuss the Transport layer in more detail in Chapter 7, Transport/Host-to-Host Layer.
Network Layer
The Network layer primarily assigns logical source and destination addresses and determines the best path for routing data between networks. The Network layer covers the following: End-to-end communication between two hosts Logical addressing Packet delivery Routing Network layer protocols deal with logical addressing, which is distinguished from the Physical layer Media Access Control (MAC) address associated with a network card. Unlike physical addresses, vendors do not burn in logical addresses (addresses that are permanently assigned). Instead, an administrator assigns them either manually or dynamically. We will discuss logical Network layer addresses in Chapters 46, Address Resolution, IP Routing, and Routing Protocols, respectively. To achieve the best routing of data, Network layer devices such as routers utilize packet switching. In this process the router identifies the logical destination Network layer address of traffic received in one interface; then sends it out on a different interface to its destination. The following protocols exist at the Network layer: RARP, ARP, BootP, DHCPProtocols that perform address resolution or configuration ICMPDiagnostic and control protocol RIP, IGRP, EIGRP, OSPF and BGPRouting protocols
Data Link Layer

The OSI Data Link layers main responsibilities include frame transmission and reception, and physical addressing. The Data Link layer adds both a header at the front and a four-byte trailer at the end of each frame prior to transmission, thereby forming a frame around the data. The term packet framing refers to the formation of such frame sequences. Only the Data Link layer adds a trailer to the data. The Data Link layer has the following characteristics and duties: Controls access to the medium. Adds source and destination hardware addresses.
13
Prepares frames for transmission by converting data packets to frames. Assumes the function of sending and receiving data over the wire. Calculates CRC or FCS. Bridges and switches function at this level.
Layer 2 Addresses
Manufacturers burn in Data Link addresses or MAC addresses on each Network Card. Manufacturers define the numbering sequences when they produce the cards. Each address is six bytes in length, as mandated by the IEEE. The first three bytes refer specifically to a vendor; the vendor uniquely assigns the last three bytes. Devices that function at the Data Link layer must have the ability to identify those addresses. The Data Link layer adds source and destination MAC addresses to the header to identify both the NIC (Network Interface Card) address of the device that sent the frame, and the local device that should receive the frame. Every MAC address has to have a unique address throughout the entire network. Layer 2 devices use the destination address to decide whether to forward information. Sending devices perform a Cyclic Redundancy Check (CRC) or Frame Check Sequence (FCS) algorithm before transmission. The industry uses the terms CRC and FCS interchangeably. The devices at the Data Link layer add this CRC or FCS as a trailer to the end of the data handed down from the Network layer framing the bits. This is why we call them frames at the Data Link layer. CRC or FCS does not guarantee delivery of data. It merely verifies that the transmitted bits match the received bits at the receiving host. Receiving hosts use the same algorithm to identify whether the frame remained undamaged during transit. If the CRC or FCS does not match, the receiving host simply tosses the frame without notifying the sending station. Stations never pass data up to the next layer unless the frame is good. The sending devices have the responsibility of retransmitting damaged frames.
Physical Layer
The Physical layer deals with 1s and 0sbits that make up the frame. Bits are encoded as electrical or light pulses. This layer also deals with electrical and mechanical characteristics, signal encoding, and voltage levels. Generally speaking, the Physical layer involves tangible items; that is, physical items that you can touch, such as cabling and repeaters. The Physical layer includes the following: Electrical and mechanical characteristics Signal encoding 1s and 0s Physical connector specifications
14
TCP/IP PRIMER PLUS
Data Link Architecture and Topologies

The term application means the literal use of the standards in the form of network architecture and specifications for the major topologies. Those standards include IEEE and ANSI specifications for: Ethernet Fast Ethernet Gigabit Ethernet Token-Ring FDDI The standards also include the frame types and channel access methods for IEEE and ANSI. The following sections provide a general discussion of these technologies as a refresher.
Ethernet and IEEE 802.3

We start with the most popular Data Link architecture, Ethernet technologies, as defined by IEEE within the 802.3 specification. The Xerox Corporation usually receives credit for inventing Ethernet; however, Xerox actually acquired the original technology (then known as Aloha Net) in the 1970s from the University of Hawaii. Xerox then joined DEC and Intel to develop the earliest Ethernet standard, called Version 1, which was released in 1980. The three companies released a follow-up standard, Ethernet Version 2, in 1982. In the mid-1980s the IEEE 802 committee adopted Ethernet as the 802.3 standard. All current and future development on Ethernet technologies ostensibly builds on this base standard. Since its inception, Ethernet has become the most popular LAN standard used throughout the world. It is important to note that Ethernet is not the same as the IEEE 802.3 implementations and the terms should not be used interchangeably (although sometimes they are). Whereas Xerox, DEC, and Intel developed Version 1 and Version 2 with somewhat similar parameters, the IEEE committee added several standard expanded capabilities not shared with its predecessors. Table 1.1 provides an overview of the similarities and differences between the three implementations.
TABLE 1.1 Version 1
Ethernet Versions 1, 2, and IEEE 802.3

Version 2 Includes Ethernet_II to detect and disable faulty frame (the defacto industry frame to carry IP traffic over Ethernet LANs) IEEE 802.3 Adds jabber control (or jabber inhibit) transceivers
Data Link layer architecture
15
TABLE 1.1 Version 1
Continued
Version 2 Delivers data at 10Mbps as linear bus topology Can use only thick coaxial media Uses balanced signaling IEEE 802.3 Expands physical topology support to star configurations Adds media types such as thin coaxial, fiber, and twisted pair 1995 enhancements provide 100Mbps transfer rates (802.3u)
Delivered data at 10Mbps as linear bus topology Could use only thick coaxial media Used unbalanced signaling with ground as reference point (susceptible to noise and EMI) Did not support Signal Quality Error (SQE) (also known as heartbeat), so more difficult to detect collisions Incompatible with Version 2
Adds SQE
Supports SQE but is necessary with only external transceivers
Incompatible with Version 1
Incompatible with Version 1
Version 1 of the Ethernet specification uses the presence or absence of voltage to represent data, known as unbalanced signaling. This type of transmission makes transmissions highly susceptible to outside interference. Figure 1.5 shows an example of unbalanced signaling.
FIGURE 1.5
Ethernet Version 1 +5 volts = 1
Unbalanced signaling varies voltage levels between 0 (referenced by ground) and +5 volts to represent data.
Reference Ground
0 volts = 0 Unbalanced Signaling
Ethernet Version 2 improved the signaling method by implementing balanced signaling, which represents data through positive and negative voltage changes using 0 or ground as a common reference point (see Figure 1.6). This approach diminishes the effects of interference on transmissions, which improves signal quality.
16
TCP/IP PRIMER PLUS
FIGURE 1.6
Ethernet Version 2 +5 volts = 1
Balanced signal improves signal quality by using a common reference point and uses positive and negative voltage levels to represent data.
Reference Ground
-5 volts = 0
Balanced Signaling
The IEEE 802.3 specification defines the general operation, components, and distance limitations of Ethernet. They are as follows: Defines all Data Link and Physical layer components, functions, channel access methods, and operations. Provides vendors with rules for implementing or developing Ethernet 802.3 LAN technologies. Is based on the IEEE standard known as 10Base5, which all other 802.3 standards follow with minor variations. The IEEE 802.3 standard defines a 10Mbps broadcast-based linear network architecture using a contention channel access method known as CSMA/CD (Carrier Sense Multiple Access with Collision Detection), which is discussed in the next section.
Channel Access Method

Various channel access methods exist today; the one that is implemented depends on the network architecture. Ethernet uses a contention-based channel access method. Channel access methods describe the rules used by devices that dictate how The communication medium is accessed. Frames are transmitted. The channel is released for use by other devices. Devices using the CSMA/CD channel access method Contend for the right to transmit. Can successfully transmit only one at a time. Must wait for channel availability to transmit a frame when other devices are using the channel (half-duplex operation). When devices transmit simultaneously on the same channel, signal collisions occur and frames become corrupted. This contention-based access is called Carrier Sense Multiple Access with
17
Collision Detection (CSMA/CD). Because Ethernet uses silence as the indication to transmit, devices perform a carrier sense to detect that silence. If no frequency exists on the wire, they can access the channel and begin transmission at once. After transmission, devices release the channel and wait at least 9.6 (microseconds) before attempting to access the channel again, thereby giving other transceivers a chance to transmit their frames.
Collisions
Collisions are just thatcollisions. In a baseband network, no more than one signal should occupy the channel at any one time. The result of more than one signal traversing the wire simultaneously is a collision, which impedes successful transmission. During transmissions a transceiver (transmitter/receiver) encodes the signal on the medium and listens for collisions. If one occurs, the transceivers internal collision detection circuitry notifies the network adapter card by sending a signal, causing the adapter to abort its transmission. It is the responsibility of the transmitting device to detect and retransmit frames when collisions occur. Collisions are a fact of life with Ethernet; however, excessive collisions or late collisions are cause for concern. Overloading a segment with too many devices causes excessive collisions. When you have too many devices attached to a segment and each one is contending for the channel, the chance of collisions increases due to sheer volume. The 802.3 specification defines late collisions as those occurring any time after the 64th byte in a frame. Exceeding the maximum distance limitations of the media (known as propagation delay or hardware failure) can cause late collisions. You should never consider late collisions a part of normal Ethernet operation.
Ethernet Frames
There are four different frame types within the realm of Ethernet standards, each designed with a different purpose by a different entity. The four frame types are as follows: Ethernet_II (DIX) Ethernet_802.3 (Novell proprietary) IEEE 802.3 IEEE 802.3 SNAP (SubNetwork Access Protocol) DEC, Intel, and Xerox developed the original Ethernet frame known as Ethernet_II (also called DIX). Novell developed its own proprietary frame (Ethernet_802.3) exclusively for IPX/SPX traffic. The IEEE developed and named the last two frames. Despite specific companies naming the frame types, the industry and IEEE have different names for the frames. The various names seem to stem largely from companies, not the IEEE, which incorporate or develop the frames into their own architectures and languages. For example, Cisco refers to the Ethernet_II frame as ARPA. Table 1.2 shows the four Ethernet frame types and compares the naming conventions used by the IEEE and industry; Table 1.3 contains information specific to each frame type.
18
TCP/IP PRIMER PLUS
TABLE 1.2 IEEE N/A N/A 802.3 802.3 SNAP
Ethernet Name Mapping

Industry Ethernet_II (DIX) Ethernet_802.3 Ethernet_802.2 Ethernet_SNAP
TABLE 1.3
Ethernet Frame Types

Ethernet_802.3 Designed to carry IP/SPX traffic Ethernet_802.2 Contains LLC headers using DSAP and SSAP addresses to identify upper-layer protocols Uses registered SAP addresses; for example, E0=IPX Ethernet_SNAP Contains LLC headers using DSAP and SSAP addresses to identify upperlayer protocols Specifies special SAP address of AA to indicate SNAP header follows with twobyte Ether type Adds a fivebyte SNAP header after the LLC header to identify the protocol
Ethernet_II -(DIX) Designed to carry IP traffic
Uses two-byte registered Ethertype values to identify protocols; for example, 0800=IP
Limited to carrying only IPX protocol
Most common frame type in use today; was de facto frame type for IPX networks prior to Ethernet 802.2
All four frame types can coexist in a single network but are not compatible. When stations configured with dissimilar encapsulation types want to exchange information they must communicate through a router that supports both types. The router performs the conversion between the hosts. Conversion adds unnecessary overhead and delays to the network, so its best to select and use only one frame type for your network. Table 1.4 shows the primary and secondary characteristics of Ethernet frames.
19
TABLE 1.4
Comparing Ethernet Frame Types

Secondary Characteristics First 12 bytes consist of 6-byte destination MAC address and 6-byte source (sender) MAC address followed by a 2-byte field defining either the length of the datagram or protocol type. Added by sender and compared by receiver to guarantee frame was undamaged. Includes 7 bytes of alternating 1s and 0s; last 2 bits of 8th byte alert stations that data follows. Includes 14-byte data link header, 4-byte trailer and up to 15 bytes of upper-layer protocols and data.
Primary Characteristics Adds a 14-byte header before transmission.
Includes a 4-byte trailer (CRC or FCS) before transmission. Sends a 64-bit preamble before transmission of each frame to achieve synchronization. Minimum frame size allowed is 64 bytes (frames of fewer than 64 bytes must be padded); maximum is 1518 bytes.
Figures 1.71.10 illustrate each type of frame. Compare both functional representations and actual appearances of the frames. Note that all these frames have the same basic characteristics. All begin with a 6-byte destination MAC address followed by a 6-byte source address. In addition, all end with a 4-byte CRC field.
FIGURE 1.7 Ethernet_II
Preamble DA SA EType 6 6 2
Upper Layer Protocols CRC
The Ethernet_II frame is the only frame that includes a 2-byte Ethertype value following the source address used to identify the protocol being carried within the frame.
<1500
Preamble = 64 Bits for Syncronization; 7 bytes of 1010 1010, 8th byte is 1010 1011 DA = Destination Address SA = Source Address Type = 2 Bytes Registered Protocol Value (for example, 0800 = IP) Data = Upper Layer Protocols, Data and Padding CRC = Frame Check Sequence
20
TCP/IP PRIMER PLUS
FIGURE 1.8
Ethernet_802.3
Preamble DA SA Length FFFF (Upper Layer Protocols) 6 6 2
Null Checksum CRC
Ethernet_802.3 frames always follow the length field with an IPX header that includes a 2-byte null checksum of FFFF .
Preamble = Synchronization DA = Destination Address SA = Source Address Length = Amount of Data contained within the Frame Must be <1500 Decimal or 05DC Hex FFFF = 2 Byte Null Checksum; IPX Header Data = Upper Layer Protocols, Data and Padding CRC = Frame Check Sequence
FIGURE 1.9
Ethernet_802.2
LLC - 802.2 Header Preamble DA SA Length DSAP SSAP Control Upper Protocols CRC 6 6 2 1 1 1 or 2 4
The IEEEs 802.3 frame, known industry wide as Ethernet_802.2, includes the 802.2 header with DSAP (destination SAP) and SSAP (source SAP) addresses for protocol identification.
Preamble = Synchronization; 7 Byte Preamble, 1 Byte SFD DA = Destination Address SA = Source Address Length = Amount of Data <1500 Decimal or 05DC Hex DSAP = Destination Service Access Point SSAP = Source Service Access Point Control = Connectionless or Connection-Oriented LLC Data = Upper Layer Protocols, Data and Padding CRC = Frame Check Sequence
FIGURE 1.10
Ethernet_SNAP LLC Preamble DA SA Len DSAP SSAP Ctrl AA AA 6 6 2 1 1 1/2 SNAP

Vendor Code Type Upper Protocols
The IEEEs 802.3 SNAP frame, known within the industry as Ethernet_SNAP, adds a 5byte extension header to the 802.2 header. This header includes a 3-byte vendor code followed by a 2-byte Ether-type identifying the protocol being carried.
CRC
Preamble = Synchronization; 7 Byte Preamble, 1 Byte SFD DA = Destination Address SA = Source Address Length = Amount of Data <1500 Decimal or 05DC Hex DSAP = Destination Service Access Point SSAP = Source Service Access Point Control = Connectionless or Connection-Oriented LLC SNAP = 3 Byte Vendor Code followed by 2 Byte EType Data = Upper Layer Protocols, Data and Padding CRC = Frame Check Sequence
21
Figure 1.11 provides a quick reference comparison of the four frame types discussed previously.
FIGURE 1.11
Frame Type Quick Reference Ethernet_II
Use the Frame Type Quick Reference to quickly identify the differences between each frame.
DA SA
EType
Ethernet_802.3
DA SA Length DA SA Length
FFFF
Ethernet_802.2
DSAP
SSAP
CTL
Ethernet_SNAP
DA SA Length
DSAP
SSAP
CTL
SNAP
Slow Ethernet
Slow (10Mbps) Ethernet has been the mainstay of LAN networks since it came out in the mid1980s. In the sense that the early days of networking were somewhat chaotic, with vendors making strictly proprietary products and the rules that governed them, it is interesting to follow the development toward official industry standards and recent improvements in them. Despite the emergence of standards-defining bodies to provide clear rules for implementing technologies (such as 802.3), desire to exceed limitations drives the industry to ignore many of those rules. Slow Ethernet specifications include the following: 10Base5Transmission takes place at 10Mbps using thick coaxial cable on a linear bus. 10Base2Transmission takes place at 10Mbps using thin coaxial cable on a linear bus. 10BaseTTransmits 10Mbps over twisted pairs in a physical star configuration.
Fast Ethernet
Fast Ethernet has exactly the same base standards as Slow Ethernet. The difference lies in the additional 10 clauses of the IEEE 802.3u addendum, released in 1995. These clauses define the standard for three different 100Mbps implementations known generally as 100BaseX. Table 1.5 illustrates a comparison between the Slow and Fast Ethernet configurations.
TABLE 1.5
Fast Versus Slow Ethernet Comparison

Fast Slow X X X
CSMA/CD channel access Same min/max frame sizes Supports same frame types
X X X
22
TCP/IP PRIMER PLUS
TABLE 1.5
Continued
Fast Slow X X X X X X X X
Supports cat 3, 4, and 5 Supports fiber Supports physical star Full-duplex/half-duplex Coaxial bus topology support Manchester signal encoding 100BaseX hardware required Component and timing changes
X X X X
100BaseX Standards
All three 100BaseX standards define 100Mb baseband technologies over twisted pair or fiber. Distance and limitations vary within each standard based on Physical layer characteristics. There are three types of 100BaseX standards: 100BaseTX Defines 100Mbps over a minimum Category 5 UTP, implementing the same two pairs as 10Mbps Ethernet. 100BaseFXDefines 100Mbps transfers over fiber-optic media. 100BaseT4Uses four unshielded twisted pairs for transmission; three pairs for transmission and reception and one pair for collision detection.
Gigabit Ethernet
The Gigabit Ethernet (GE) standard enables transmission speeds of up to 1000Mbps using Category 5 UTP cabling. The task force specification is the IEEE 802.3z, which uses 802.3 Ethernet frame formats, and the CSMA/CD access method. Note that the continuing use of the 802.3 standard supports backward compatibility with the 100BaseT and 10BaseT technologies.
Token-Ring and IEEE 802.5

Although IBM usually is considered to be the founder of the Token-Ring LAN standard, Dr. Olaf Solderblum in Sweden actually patented it in 1967. IBM obtained the technology from Dr. Solderblum, and with the assistance of Texas Instruments, developed the chipset technology and guidelines. IBM released the technology to the IEEE, whose 802.5 subcommittee developed and released the 4Mbps Token-Ring standard in 1985. The IEEE 802.5 specification defines the MAC sublayer and the Physical layer specification, using the 802.2 specification at the LLC layer for protocol identification. In 1989 the IEEE released an enhancement to the 802.5 standard that defines 16Mbps Token-Ring operations.
23
Token-Ring uses a unidirectional transmission, with each device always receiving from its upstream neighbor and sending to its downstream neighbor. It utilizes token-passing ring topology that passes frames with no collision risk because only one device can transmit at a time. However, devices can access the medium and transmit upon reception of a free token, which is a 3-byte signal that propagates around the ring. Token-Ring exhibits these important characteristics: All devices connect serially, transmitting a signal in one direction. Each devices transmit pair connects through to its downstream neighbors receive pair. Signal transmission is unidirectional. Each device directly connects in a physical star formation through central hubs known as Multi-Station Access Units (MSAUs) (see Figure 1.12). The MSAUs objective is to keep the ring functional by electrically bypassing a non-functional device or port when end devices are either turned off or fail.
FIGURE 1.12 Token - Ring
Token-Ring operation.
Tx
Rx Tx
Rx MSAU Rx Tx Rx
Tx
Each devices network card operates as a fully functional unidirectional repeater, completely regenerating the signal and bit repeating it on. Operates at either 4Mbps or 16Mbps, but not both, as determined by the configuration of the network card. All devices must agree on the speed of the ring.
Bit Repeating
The industry uses the term bit repeating to describe the amplification and regeneration of a received signal that is repeated out all other interfaces.
24
TCP/IP PRIMER PLUS

Token-Ring devices access the channel using a token-passing method. When a device has information to transmit, it waits for a free token, a 3-byte frame that traverses the ring and provides access to the medium. When it receives a token it can convert it to a frame. Stations send their frames around the ring hoping to find the destination host. All other devices on the ring check the destination address of the frame to determine whether it is for them; then they bit repeat the signal on. Each network interface card acts as a repeater, amplifying, retiming, and bit repeating the signal. The responsibility of stripping its frame and releasing a new token belongs to the sending device.
Token-Ring Frames
The two types of Token-Ring frames are token and data/command. Figure 1.13 shows an example of a token frame. In Figure 1.13, stations identify the signal as a free token by looking at the status of the token bit within the AC field. If the bit contains a 0 in the AC field, it is a token frame. SDs and EDs simply mark the beginning and end of a frame. Figure 1.14 shows an example of a Token Ring frame used to transmit data and commands. Note that the MAC/LLC field following the SA (source address field) indicates whether the frame is a command (MAC) or data frame (LLC).
FIGURE 1.13 Token Frame
SD AC ED
A 3-byte signal circles the ring providing attached devices with access to the channel.
SD = Start Delimiter AC = Access Control byte indicates whether this is a Token or Data/Command frame ED = End Delimiter
FIGURE 1.14
Token-Ring Frame
SD AC FC DA SA MAC or LLC RIF Upper Layer Data FCS ED FS
The structure of a Token-Ring frame with field descriptions.
SD = Start Delimiter for frame AC = Access Control byte indicates whether this is a Token or Data/Command frame FC = Frame Control indicates whether frame is a Data (LLC) or Command (MAC) frame DA = Destination Address SA = Source Address MAC or LLC = MAC frames carry MAC data. LLC frames contain 802.2 header for protocol identification RIF = Route Information Field, only exists when Source Route Bridging is being used Upper Layer Data = Headers for upper layer protocols and User Data FCS = Frame Check Sequence, similar to CRC ED = End Delimiter for frame FD = Frame Status byte used to identify whether recieving device recognized and copied a frame
25
FDDI and ANSI X3T9.5

Fiber Distributed Data Interface (FDDI) is a type of media access defined by the American National Standards Institute (ANSI) X3T9.5 specification. Although FDDI also uses a MAC addressing scheme, it differs from Ethernet and Token-Ring. The difference is that instead of referring to the MAC address in terms of a 6-byte address (like other topologies), FDDI uses 4bit symbols to refer to the MAC addresses. FDDI incorporates token passing in a dual-ring physical topology, which provides a selfhealing redundancy. If there is a problem with the primary ring, the secondary ring serves as a backup. If a break occurs, it reroutes the data from the primary ring to the secondary ring at two or more locations. This is known as a ring wrap. FDDI once was a favorite standard for network backbones because it enables transmission speeds of up to 100Mbps and, unlike copper, is immune to EMI and RFI. In fact, fiber-optic cabling has many advantages over conventional copper cable, including the following: Speed at which data can travel Signal distance achieved before attenuation Immunity to EMI and RFI Redundancy in having counter-rotating rings
Note
Note that FDDI once was a favorite standard for backbones; however, most places have replaced FDDI with the cheaper Fast or Gigabit Ethernet.

FDDI uses a token access method for transmission of packets. FDDI communications access the physical medium (the ring) through the token being passed around the ring. When a node wants to transmit, it simply grabs a token, sends its transmission, and then releases a new token on the ring. Note that unlike with Token-Ring, which allows only one token to circulate at a time, FDDI allows multiple tokens to circulate at any given time.
Note
Although Token Ring vendors did implement something called early token release to allow for multiple transmissions on the ring at a time, only one token is allowed.
Wide Area Networking (WAN) Technologies

WAN (Wide Area Network) technologies use transmission facilities provided by common carriers, such as service providers or telephone companies, to provide a data path to networks
26
TCP/IP PRIMER PLUS
covering a broad geographical area. WAN technologies operate at the lowest two levels of the OSI modelthe Physical and Data Link layers (see Figure 1.15).
FIGURE 1.15 OSI WAN Protocols
Mapping the OSI model to WAN protocols.

Network X.25
Data Link
HDLC, ATM, X.25 LAPB, LAPD, Frame Relay, PPP, SLIP EIA/TIA-232 and 449, V.35, X.21 and EIA 530
Physical
WAN connection types enable companies to connect to remote sites to extend their networks. Most companies that have remote sites over a large geographical area require some sort of WAN connection type. Which connection type they choose depends on a companys specific needs. Three WAN connection types can be used to transfer data across a service providers network: Leased (dedicated) lineThe leased line, also known as a point-to-point or dedicated line, employs a synchronous serial connection through a service provider. Circuit-switchedCircuit-switched has a dedicated circuit path and employs an asynchronous serial connection through a telephone company. Packet-switchedPacket-switched uses a synchronous serial connection through a service provider. Table 1.6 explains the three connection types.
TABLE 1.6
WAN Connection Types, Layer One

Description Provides a single, existing WAN communications path through a service provider network, from a customer to a remote network. Service providers reserve the connection and bandwidth for a clients private use. Guarantees bandwidth is available. Has the drawback of being expensive because connection is always active even if its unused. Employed over synchronous serial connections up to E3 speeds, 45Mbps. Supports PPP, SLIP, and HDLC Data Link encapsulations.
Connection Type Leased Line (also known as point-to-point or dedicated)
27
TABLE 1.6
Continued
Description Dedicated circuit or path is built on the fly for each session and must exist between sender and receiver for the duration of the transmission. Commonly used in environments that require only minimal or infrequent WAN usage. Used to provide asynchronous serial connections over standard telephone lines or ISDN connections. Supports PPP, SLIP, and HDLC encapsulations. WAN switching method. Network devices share common point-topoint links to deliver packets from a source to a destination across a service providers network. Establishes temporary virtual circuits (VCs) to provide an end-to-end connection between source and destination. Switching devices establish the virtual circuit and use multiplexing devices to provide customers with shared access to the circuit. Less expensive because the circuit is not dedicated. Employed over a serial connection with speeds ranging from 56Kbps to E3. Supports X.25, ATM, and Frame Relay encapsulation.
Connection Type Circuit-switching
Packet-switching
Figures 1.16, 1.17, and 1.18 show the different WAN connection types. A leased line, known as a dedicated line, provides a single existing WAN communication path through a service provider network, from a customer to a remote network (see Figure 1.16). Figure 1.17 shows a path being built on the fly for a WAN circuit-switched connection. Figure 1.18 shows an example of packet-switching.
FIGURE 1.16
Leased Line
Leased lines tend to be expensive because the connection remains active even when not in use.
Switch Switch
Router Switch Switch
Router
Msg 2
Switch
Switch
Msg 1
28
TCP/IP PRIMER PLUS
FIGURE 1.17
Circuit Switching
Circuit-switching requires that a connection be set up and torn down for each session between the sender and receiver.
Router Switch
Switch
Switch
Router Switch
Msg 2
Switch
Switch
Msg 1
FIGURE 1.18
Packet Switching
Packet-switching relays packets from node to node, occupying the channel only for the duration of transmission.
Switch
Switch
Ms g2
Router Switch Switch
Router
Switch
Switch
Msg 1
Service providers and telephone companies provide most of the WAN connections today. You can use routers to access servers providing circuit-switched dial-up connections through standard analog modems or dial-on-demand routing (DDR) over analog or ISDN lines. You can configure dedicated leased line connections through CSU/DSUs to support consistently high volumes of traffic over synchronous serial connections. Packet-switched connections, such as X.25, ATM, and Frame Relay, require that Multiplexer/Demultiplexer (MUX/DEMUX) devices be used to provide devices with shared access to the same circuit. You can use any of these methods to deliver data across a service providers network to remote sites all around the world.
29
WAN Encapsulation Protocols

WAN encapsulation is a way of wrapping a packet to enable it to traverse a mesh of distanceseparated networks. The Internet is based on many different types of WAN connections, including dedicated and non-dedicated. On each WAN connection, local LAN data must encapsulate into frames before crossing the WAN link. You need to know the proper protocol to configure the appropriate Data Link layer encapsulation type. The protocol depends on the WAN technology being used; your service provider should provide you with the specific configuration information to connect to their network successfully. Several options can provide an interface to a service providers network. These options are all variations of the High-Level Data Link Control (HDLC) protocolthe widely used standard introduced by the ISO, which was patterned after IBMs Synchronous Data Link Control (SDLC) protocol. These protocols operate at the Data Link layer of the OSI model, providing Data Link layer connection-oriented and connectionless services to upper-layer applications and user data across the WAN. Most WAN protocols come from descendents of HDLC. Vendors have several implementations of HDLC, and not all are compatible. For instance, Cisco has its own proprietary HDLC implementation, which is incompatible with other HDLC protocols. IBMs SDLC protocol, used in its Systems Network Architecture (SNA), is very similar in functionality and provides connectionoriented, reliable delivery between IBM minis, mainframes, and their clients. Other protocols, such as X.25s LAPB, ISDNs LAPD, and even LLC2, are all subsets of HDLC. Table 1.7 shows the primary WAN encapsulation protocols.
TABLE 1.7
Primary WAN Encapsulation Protocols

Description Establishes multiple virtual logical paths or virtual circuits. Operates at the Data Link and Physical layers. More efficient than X.25 because it does not establish connections and does not employ error correction or recovery. Assumes most networks are physically reliable and have low error rates. Relies on upper-layer protocols for error detection and recovery. Frame relay supports congestion control. Uses existing telephone lines to transmit data, voice, and other source traffic. Uses two types of channels: D and B. D channel carries signaling and control information. B carries data. There are two main types of ISDN services: BRI (Basic Rate ISDN) and PRI (Primary Rate IDSN). BRI supports total bit rate of 144Kbps, and PRI supports 1.544Mbps (in the U.S., Canada, and Japan) or 2.048Mbps (in Europe).
Protocol Type Frame Relay Two encapsulation types: Frame relay (Ciscos encapsulation) Frame relay IETF (RFC 1490 standard encapsulation) ISDN (Integrated Services Digital Network)
30
TCP/IP PRIMER PLUS
TABLE 1.7
Continued
Description LAPB is the Data Link layer protocol in the X.25 protocol stack. Derived from HDLC, it is a connection-oriented protocol that provides error detection and recovery at layer two. Extremely reliable but slow because of the high overhead involved in connection maintenance. Good to use if your WAN link is prone to error. It has generally been replaced by Frame Relay and other WAN standards. Connection-oriented protocol at the Data Link layer introduced by ISO. Does not support data compression or authentication. ISOs HDLC cant identify the type of protocols being carried inside HDLC encapsulation. Therefore, only one protocol can be carried over HDLC at a time. Vendor implementations vary. Provides a communications path from the customer over an established WAN asynchronous connection, and a synchronous connection over a carrier network to a remote network. Supports multiple protocols, such as IP, IPX, and AppleTalk. Supports data compression authentication, error detection, and multilinking. Older protocol supporting point-to-point serial connections using TCP/IP. Replaced by PPP. International standard for cell-based switching and multiplexing technology. Supports multiple service types (voice, video, and data) through fixed-length (53-byte) cells. Fixed-length cells reduce processing overhead and transit delay. Supports high-speed transmissions over copper or fiber lines with data rates ranging from 1.544Mbps (T1 service) up to 622Mbps (OC-12).
Protocol Type X.25 LAPB (Link Access Procedure, Balanced) encapsulation for signaling channel
HDLC (High-Level Data Link Control)
PPP (Point-to-Point)
Serial Line Internet Protocol (SLIP) Asynchronous Transfer Mode (ATM)
Request For Comments (RFCs)

No one owns the TCP/IP technologies, nor can one obtain information in the form of documentation, policies, protocols, and standards from a vendor. However, you can find this type of documentation online at no charge in the form of Request for Comments (RFCs). Although vendors do publish documentation on the implementation of these technologies, RFCs provide the base standards, describing protocol functions, rules, and methods of implementation; vendors interpret these standards. RFCs provide documentation in the form of a series of technical reports written by committees, individuals, and corporations for the development of various protocols, policies, implementations, and so on. The RFCs appear in chronological order; revised RFCs supersede
31
earlier documents and are assigned new numbers. We recommended that you be careful to obtain the latest RFC when researching. RFCs vary from technical documentation of a protocol to suggestions for changes to proposals for new protocols and can range from dry and academic to humorous in tone. In this book, we refer to RFCs as a reference. We also provide a categorized list of RFCs in Appendix A, RFCs Organized by Chapter. You can access RFC through the Web at http://www.faqs.org/rfcs/.
Internet Versus intranet

You might have heard the saying All cognacs are brandies but not all brandies are cognacs. The same analogy holds true of the Internet and intranet. Although the uppercase Internet is an intranet, an intranet is not the Internet. The lowercase intranet means multiple networks (within a company) connected together and communicating internally with a cohesive governing body (algorithm). The uppercase Internet allows numerous people (hosts) from different organizations around the world with no controlling body to talk to each other using TCP/IP. Just as a brandy is not as grand as a Cognac (but similar in design), so is the lesser intranet to the grander Internet.
Groups Responsible for Internet Technology

The industry is in a constant state of change, and it seems new protocols and standards appear out of thin air. However, the following four groups govern Internet technologies: The Internet Society (ISOC)A non-profit organization that promotes interest in the Internet. Host organization of the IAB (Internet Architecture Board). The Internet Architecture Board (IAB)Small group of international volunteers that set policies for the quality of Internet (TCP/IP) standards. Falls under the ISOC. The Internet Engineering Task Force (IETF)A small standards-oriented group divided into specific areas of TCP/IP and the global Internet. Each area has an independent manager and working groups. The Internet Research Task Force (IRTF)A group that works on research projects related to the TCP/IP and the Internet.
Summary
The OSI Reference Model was created to enable both similar and dissimilar systems to communicate seamlessly by providing an architectural framework for vendors and manufacturers. It consists of seven layers: Application, Presentation, Session, Transport, Network, Data Link and Physical.
32
TCP/IP PRIMER PLUS
The OSI model benefits manufacturers and software developers, and network engineers who offer support and troubleshooting. By compartmentalizing each layers function, it narrows the scope of each layers responsibilities. This eases the development and support burdens that manufacturers and network engineers face.
Review Questions
1. What is the reason for the importance of the OSI model and why was it created? 2. Which layer of the OSI model manages the communication dialog (full or half duplex) between services? 3. Which layer provides error handling and flow control as well as guaranteed delivery? 4. At which layer of the OSI model does switching occur? 5. At which layer of the OSI model do IP and ICMP function? 6. Name the four layers of the DoD model. 7. What are two functions of the Data link MAC Layer? 8. Name the Transport layer protocol that is connectionless?
CHAPTER 2
IP ADDRESSING

Binary to Decimal Conversion IP Addressing Subnetting Network Address Translation (NAT)
Understanding Binary to Decimal Conversion

Before you can understand the derivation of IP addresses you must have a basic understanding of decimal and binary numbering, and how to convert from one to the other. For those unfamiliar with binary and decimal numbers, the base-10 numbering system is referred to as the decimal numbering system. Decimal numbering consists of the numbers 0,1,2,3,4,5,6,7,8, and 9. This comprises the 10 unique digits of 0 through 9. Computers use the binary numbering system, which consists of only two unique numbers 0 (zero) and 1 (one). Computers recognize only the uncharged 0 and charged 1. Unlike decimal numbering, binary numbering uses powers of 2 rather than powers of 10 (see Figure 2.1). To understand binary numbers we convert them to the decimal numbering system. A byte (also called an octet), which measures storage and memory, is composed of 8 bit positions, with a maximum value of 255. Binary numbering uses powers of 2 for each bit position. As shown in Figure 2.2, moving from right to left, beginning with the number 1 and moving to 2, each position is equivalent to the value squared of the previous position. The last position on the left is equal to 128. To convert a number from binary to decimal, assign the decimal value to each corresponding bit position; then add them together. Remember that the computer recognizes only the number in the on position, represented by 1. The highest possible total is 255 if all bits are in the on position (128+64+32+16+8+4+2+1). That is, 128+32+8+4=172 or in binary numbers, 10101100.
34
TCP/IP PRIMER PLUS
Note
Remember when you convert binary to decimal, add only the numbers in the on position. The on position is represented by the number 1 and is the only number that the computer recognizes.
To convert 172 to its binary equivalent, place a 1 under the bits (turning them on) until the total equals 172. Use Figure 2.3 and the number 176 as an example. In binary, 176 is represented by placing a 1 under the 128 at the far left. Again, 128 is the largest number within our numbers (to the power of 2) in our byte (8 bits). As 128 is the largest number, you build upon it for any numbers larger than 128.
FIGURE 2.1
Binary (Base-2) The Binary Number System uses 2 values to represent numbers 0 and 1 8 Bits=1Byte 1011 0100
The binary numbering system uses the base-2, not base-10 system.
FIGURE 2.2
Binary to Decimal Conversion 27 128 X 1 64 X 0 32 X 1 16 X 0 8 X 1 4 X 1 2 X 0 20 1 X 0
The number 1 indicates that the bit is in the on position.
128 + 32 + 8 + 4 = 172
If you place a number 1 (on position) under the 64, the sum (64+128) adds up greater than the value of 176, so you place a zero (off position) under the number. If you add all the numbers, except 32, it totals less than 176; so place a 1 under the number 32 for a total of 160. You need a sum of 16 to reach 176, which means you place a 1 under the 16, giving you a total of 176. You then place zeros under the remaining numbers. Your binary number is 10110000.
FIGURE 2.3
Decimal to Binary Conversion 176 27 128 X 1 64 X 0 32 X 1 16 X 1 8 X 0 4 X 0 2 X 0 20 1 X 0
The 1s represent the numbers the computer recognizes.
Chapter 2 IP ADDRESSING
35
IP Addressing
In Chapter 1, Overview of Industry Models and Standards, we discussed Data Link layer two (MAC) addressing, and how those addresses uniquely identify devices on a network. We now move up one layer in the OSI model to the Network layer. As you recall, the Network layer controls routing and the decision of where to route traffic. Those routing decisions stem from information in the 4-octet, or 32-bit destination IP address. The parameters for a unique 32-bit value to define both the network and host portions with a 2-level addressing hierarchy appeared in the 1985 publication Request for Comment (RFC) 950. Its purpose is to logically divide the IP address into at least 2 parts, identifying the network and device, such as a router, and maybe even a third part that describes a subnetwork within the network. A subnet is an extension of the IP addressing scheme and we will discuss subnetting later in this chapter. The hierarchy differentiates the network address and subnetwork within the network from the node address. A node address uniquely identifies an individual device on a given subnet or network, and that network is assigned to a company identifying the major network as a whole. Think of the logical network assigned to an organization as a city, the subnet as a street within the city, and each unique logical host portion of the address as a specific house. For example, if someone asks where you live, you might respond with San Francisco and leave it at that. The general term San Francisco gives someone a reference point for where that city is located and the path to get there. However, it says nothing about how to specifically find you once he or she gets to San Francisco. Because thousands of streets (subnets) and houses (hosts) exist within San Francisco, this person would require more specific information if he or she actually tried to find you. In this analogy, the network and subnet portions of the address are what the router uses to identify which city and street receives the routed traffic. Once a datagram reaches the street (subnet), it can easily find the house (host) because each house (host) has a unique address on that street (subnet).
Address Classes
When the Internet community developed an addressing scheme it divided the 32-bit or 4-byte addresses into classes based on predicted use. They defined these addresses as classful because they clearly differentiate the classes in predefined boundaries. There are five major classes of network addresses: Classes A, B, C, D, and E. You obtain these registered Internet addresses through ARIN (American Registry for Internet Numbers), which assigns them based on your network size or class. The ARIN organization makes these assignments to individual companies and Internet service providers based on the size of network defined by the class type. The Internet community originally defined the classes to address networks of varying sizes designated by their high-order bits, and with specific ranges. Table 2.1 exhibits this information for Classes A, B, and C.
36
TCP/IP PRIMER PLUS
TABLE 2.1 Attributes
Attributes of Class A, Class B, and Class C Addresses

Class A (Slash /8) Meant to define the relatively few networks such as government, university, military, and research facilities in which a vast number of hosts exist. Class B (Slash /16) Encompasses large numbers of networks with equally large numbers of hosts, as in medium-sized companies. Begin with 10 as their first two bits. 128-191 2 Bytes 2 Bytes 16,384 65,534 Class C (Slash /24) Intended to tackle the needs of small networks by providing a very large number of network addresses with a minimal number of hosts per network. Begin with 110 as their first three bits. 192-223 3 Bytes 1 Byte 2,097,152 254
Size
Bit Designations Value Range Assigned Network Bytes Available Host Bytes Number of Networks Number of Hosts
Begin with zero (0) as their first bit. 1-126 1 Byte 3 Bytes 126 16,777,214
Classes D and E addresses have special uses and are not assigned to mainstream networks. Class A network 127 is reserved as a loopback address (127.0.0.1) used for testing purposes.
To further explain the designation of bits, the first 7 bits within the first byte of a Class A address (the first bit is a zero) define the network address, or NetID. You can use the last 24 bits (3 bytes) to define multiple subnetworks and uniquely identify hosts within the network if the network has been subdivided. If you have not subdivided the network, the remaining bits within the last three bytes define hosts. Class B addresses begin with a starting 2-bit value of 10 within the first byte and use the remaining 14 bits within the first and second bytes as the NetID. You can use the second 2 bytes to define additional subnetworks (if you have subdivided the network) or hosts. Following this pattern, Class C addresses use the first 21 bits (within the first three bytes) and begin with a value of 110, which identifies the NetID. You can use the last byte to define subnetworks and hosts on these subnetworks. Figure 2.4 shows the structures of Classes A, B, C, D, and E addresses.
37
FIGURE 2.4
IP Adress Classes Class Type Class A Class B Class C Class D Class E First Byte Range 1 to 126 128 to 191 192 to 223 224 to 247 248 to 254
Note that only A, B, and C are for public use.
Default Mask 255.0.0.0 255.255.0.0 255.255.255.0 Used for Multicast Broadcasts Reserved
127.0.0.1 is Loopback Address
Figure 2.5 shows the class addresses in bits. Note that Class A has 7 bits for network and 24 bits for hosts; Class B has 14 bits for network and 16 bits for hosts; Class C has 21 bits for network and 24 bits for hosts.
FIGURE 2.5
5 Classes of Addresses A 0 net (7 bits) host (24 bits)
Note that the number of hosts and networks you have available depends on what address class you have: A, B, or C.
10
net (14 bits)
host (16 bits)
1 10
net (21 bits)
host (8 bits)
1110
reserved for multicast addresses
11110
reserved for experimental use
Each of the preceding address classes define major classful boundaries. You can further subdivide these address classes to allow for subnetworks within a single network rather than many hosts on one network. This subdivision requires that you allocate the leftover bitsanything not assigned by ARINto subnets and hosts. We discuss the topic of subnetting later in this chapter. For now lets keep it simple: Assume the assigned network has not been subnetted and all leftover bits are host bits only. This is a representation of classful addressing, in which only the major class-based network address defines the network.
38
TCP/IP PRIMER PLUS
Class A
Class A networks, or Slash 8 (8-bit registered addresses) begin with the first (high order) bit of zero, followed by another 7 bits that define the network number, and 24 variable bits that can define host addresses for that network. Slash 8 describes the total number of bits within the subnet mask that indicate the network portion of the address. RFC 950 puts networks in this class within the range of 1 through 126. The limitation for the maximum number of networks 7 uses this algorithm: 2 2. To understand it, remember that the leading bit of 0 occupies the first bit. You must subtract 2 because a 0 in the first byte or network portion is not a legal network address. Additionally, the value 255 is reserved as a broadcast address. As you will soon discover, 126 networks is not a large number. However, your tradeoff is a large number of possible hosts resulting from the last three bytes. More specifically, the for24 mula to determine the maximum number of hosts with a Class A address is 2 2, which equals a total of 16,777,214 hosts per network. Again, you subtract 2 because an address of all 1s with this 24-bit range indicates a broadcast to all hosts on the network, and an address of all 0s simply designates the network and is not a valid host address. Those in Class A have an address range of 1.xxx.xxx.xxx through 126.xxx.xxx.xxx. You must consider one more address as a Class A address: 127. However, this particular address is a loopback address and cannot be used as a standard network address. You typically would use IP address 127.0.0.1 to verify that a devices internal IP configuration functions properly by pinging this address. Although technically we consider this address a Class A because of its special use, ARIN would not give it out as a network address.
Class B
Class B, or Slash 16, networks follow the same basic formula as described above in that the first 14 bits, with the first 2 bytes, are assigned by ARIN as the network ID. Slash 16 describes the total number of bits within the subnet mask that indicate the network portion of the address. This leaves the second 2 bytes available for the host ID. The first two high order bits within the first byte of a Class B address always equal 10. The maximum number of networks 14 is 2 , which equals 16,384 networks. With 16 bits left over for hosts, you can assign a total of 16 2 2, or 65,534 hosts per network. Those in Class B have an address range value of 128.0.xxx.xxx through 191.255.xxx.xxx.
Class C
Class C, or Slash 24, networks have the value 110 for their first 3 high order bit designations. Slash 24 describes the total number of bits within the subnet mask that indicate the network 21 portion of the address. Following the same basic formula, you can get 2 , equaling 2,097,152 8 networks, with a total of 2 2, or 254, hosts per network. You can easily identify Class C addresses if the value within the first byte falls in the range of 192 to 223.
39
Classes D and E
As previously noted, the public cannot use Classes D and E. ARIN reserves Class D addresses for multicast addresses, and it is not for use by individual hosts on a network. The Class D address range is between 224 to 239. ARIN has reserved the Class E address for future use. Its address range falls between 240 and 247.
Reserved Addresses
Reserved addresses can be used for a variety of special purposes. These specific addresses and ranges, which remain reserved and have restricted uses, include 255.255.255.255 An entire IP address set to all ones, such as this one, signifies a network-wide message sent to all nodes and all networks. Used for broadcast purposes. 0.0.0.0 An IP address set to all zeros represents an unknown network or host, and typically is used to define a default gateway of last resort. 127.0.0.1 This is a special Class A address used for internal loopback testing. It designates the local node and will not generate any network traffic. Although IP address 255.255.255.255 is considered a network-wide flooded broadcast, routers do not forward this type of broadcast. Routers isolate broadcasts to subnets. To broadcast to all hosts on a subnet or network, set all host bits to ones. For example, to send a broadcast to all hosts on a Class B network 131.107.0.0 with a standard mask of 255.255.0.0, you would specify the destination address as 131.107.255.255. Reserved addresses also include private networks. RFC 1918 defines private networks as the following: 10.0.0.0-10.255.255.255 172.16.0.0-172.31.255.255 192.168.0.0-192.168.255.255. You cannot use the nonregistered private addresses on the Internet. However, companies commonly use them internally within a companys network. Many companies use the 10.x.x.x private network because it offers internal addressing flexibility. With 3 bytes available for subnetworks and hosts, it provides more than enough bits to handle any companys IP addressing needs. With registered IP addresses becoming scarce, it is common to use inside private addressing schemes with address translation mechanisms allowing one or two outside registered addresses to be used for Internet access. Translation between inside private addresses and outside registered addresses is defined as NAT (network address translation). Typically, a gateway (router) or firewall connecting a companys network to the outside world or Internet, where private addresses are not allowed, is responsible for the NAT process. We discuss NAT in further detail later in this chapter.
40
TCP/IP PRIMER PLUS
Network and Subnet Masks

You might wonder, What are subnet masks, and why do we need them? The simple answer is that they are address indicators that end hosts and routers use to determine whether to shout or route traffic to forward datagrams to a destination host. You might ask, What do shouting and routing mean? The short answer is that if a sending end host knows a destination host resides on the same local segment, it can shout a local Address Resolution Protocol (ARP) broadcast to resolve the logical Network layer IP address to a MAC address. Conversely, if the sending host knows the receiver resides on a remote subnet or network, the sender has to route the frame by sending it to a local gateway router. A sending host uses its local mask to determine whether to shout or route. We will discuss address resolution and the ARP protocol in more detail in Chapter 4, Address Resolution. Each of the three classful network types comes with a corresponding default classful subnet mask. As previously mentioned, Class A addresses use a default mask of 255.0.0.0 or Slash 8 (/8). Class B addresses use a default mask of 255.255.0.0 or Slash 16 (/16). In this case, notice that the first 16 bits have been masked off by turning on each of the 8 bits within each of the bytes. If you add up the value of all the bits within each octet, you come up with a maximum value of 255. The last 16 bits remain unused (and not defined for network purposes), thus all are 0s and remain available for subnets and hosts. Class C addresses have a default mask of 255.255.255.0 or Slash 24 (/24), indicating that the first 3 bytes of this address definitely are part of the network. This leaves the last 8 bits unmasked and available for subnets and hosts. For example, host 166.3.22.1 (note the Class B address) wants to establish a connection to a remote Telnet server 151.10.5.2 (another Class B address). Its important to understand that sending hosts have absolutely no idea where the destination host really resides. That is, the IP address of the destination host alone does not tell the sender where or how get to that host, or even if it resides on the local segment. For the sending host to determine whether the destination host resides on the same local segment, the sender compares the sending hosts subnet mask to the destination hosts IP address. If the sender finds that the receiving host resides on the local subnet it knows that it can shout (send) a local ARP to resolve this logical address to a MAC address. The source host must determine whether the destination host resides on the same subnet by performing bitwise ANDing, which compares the destination hosts IP address to the sending hosts subnet mask. Until it conducts bitwise ANDing the source host has no idea whether this host is local or remote. (We will discuss bitwise ANDing later in this chapter.) If the sender determines that the host does not reside on the local segment (remote), it knows that sending a local ARP will not reach the remote host. The sending host now knows it must route the frame by sending it to a local gateway router. To get the datagram to the router for forwarding, this host must know the MAC address of the local gateway. Hopefully this host has already used this gateway before and still has this information in cache. If not, the sending host must send a local ARP to resolve the gateways IP address to a MAC address before it sends datagrams for forwarding (see Figure 2.6).
41
FIGURE 2.6
Depending on whether the destination resides locally or remotely determines how the router goes about resolving the address.
Can I Shout? Or do I Route?

Source IP Address is: 166.3.22.1 Destination Host: Source Host MASK: 151.10.5.2 255.255.0.0
It is important to note that an improperly configured subnet mask could cause an end host to shout (send out a local ARP broadcast for the end host) when it should route, (send out a local ARP broadcast for the gateway) and vice versa. For example, lets say Host A and Host B reside on the same physical segment. The user on Host A (IP address 155.10.1.1) types in Telnet and the IP address, wanting to connect to Host B (IP address 155.10.2.2). However, Host A cannot determine that Host B is on the same segment until it compares its address to Host As mask. Both hosts have Class B addresses, meaning the first 2 bytes are the network address, which is 155.10.0.0, and should have a mask of 255.255.0.0. However, Host As mask is incorrectly configured as 255.255.255.0. This causes Host A to think the first 3 bytes are the network address. When Host A compares this mask to Host Bs IP address, it assumes Host B is remote because its address appears to be 155.10.2.0. This causes Host A to route (send out a local ARP broadcast for the gateway) and forward datagrams to the gateway destined for Host B instead of shout (send out a local ARP broadcast for the end host and forward datagrams directly to Host B). If Host A had the proper subnet mask, it would have found that Host B was on the same local subnet and simply sent a local ARP broadcast to resolve Host Bs IP address to a MAC address. It then would forward datagrams to that host without help from a gateway. Because Host A has bad information it makes a poor choice, sending what should be a local frame to the gateway instead. Assuming the gateway is properly configured, it performs the same IP address to subnet mask comparison, determines that Host B resides on the local subnet, and retransmits the frame back out the same interface on which it received it. The gateway also sends an ICMP (Internet Control Message Protocol) redirect message to Host A notifying it that there is a better way to send this frame. (We discuss ICMP messages in more detail in Chapter 3, Network Layer/Internet Protocols; and ARP and RARP in Chapter 4.) However, this does not resolve the problem of a misconfigured mask on Host A. The best way to resolve this problem is to fix the subnet mask on Host A; otherwise Host A will continue to send local frames to the gateway when they could be sent directly to local hosts on this segment.
42
TCP/IP PRIMER PLUS
Bitwise ANDing
Bitwise ANDing compares the destination hosts IP address (see Figures 2.7 and 2.8) to the sending hosts subnet mask, a process that is governed by a set of rules. Before beginning the process of ANDing, you must convert these addresses to their binary forms so you can understand how the comparison occurs. Bitwise ANDing has the following rules: If both values are one, the result is one. If one of the values is zero, and the other is one, the result is zero. If both of the values are zero, the result is zero.
FIGURE 2.7
Destination Hosts IP Address: 151.10.5.2 Sending Hosts Mask: 255.255.0.0
Note that during Bitwise ANDing the number remains one only if both values are one.
10010111.00001010.00000101.00000010 Mask 11111111.11111111.00000000 00000000 10010111.00001010.00000000.00000000
Network# 151.10.
Using Figure 2.7 as an example, determine whether the destination host resides on the same local subnet as the sending host. To determine this: 1. Compare the destination hosts IP address with the sending hosts subnet mask. The destination hosts IP address is 151.10.5.2; the senders mask is 255.255.0.0. 2. Convert the IP address and subnet mask to binary. 3. Draw a line vertically to separate the masked area (which represents the network address) from the unmasked area (which represents the host portion). 4. Consider any values within the IP address falling within the masked portion on the left to be part of the network. In this example, the first two bytes have been masked off and represent the network (151.10) or 151.10.0.0. 5. Any values to the right of the vertical line represent the host address with the last two bytes being 5.2. Remember routers only care about the network and subnet in terms of routing traffic to a destination. Using Figure 2.8 as an example, determine whether the sending host resides on the same subnet as the destination host. To determine this: 1. Compare the IP address of the destination host with the subnet mask of the sending host. 2. With an IP address of 166.3.22.1 and a standard Class B mask of 255.255.0.0, convert both the IP address and mask to their binary equivalents to identify which part of this address represents the network or subnet.
43
3. Draw a line vertically to separate the masked area (which represents the network address) from the unmasked area (which represents the host portion). 4. Consider any values within the IP address falling within the masked portion on the left to be part of the network. In this example, the first two bytes have been masked off and represent the network (166.3). 5. Any values to the right of the vertical line represent the host address with the last two bytes being 22.1.
FIGURE 2.8 Host As address and Mask: IP Address = 166 . 3 . 22 . 1 Mask = 255 . 255 . 0 . 0
10100110.00000011.00010110.00000001 11111111.11111111.00000000 00000000 10100110.00000011.00000000.00000000 MASK Network# 166.3.
To compare the subnet mask of the sending host and the IP address of the destination host, convert the decimal value into binary.
Note that host 5.2 does not reside on the same subnet with host 22.1 on subnet 166.3, listed in Figure 2.7. As a result, Host A sends the frame to its gateway instead of directly to Host B. The router then forwards the frame onto the adjacent segment to Host B (see Figure 2.9).
FIGURE 2.9 Misdirected Frames
Incorrect Mask
Host A has been configured with the wrong mask and should be sending datagrams to Host B, which is local.
A
B Data Frame
T
ICMP Redirect Router Data Frame
44
TCP/IP PRIMER PLUS
Subnetting and Examples

Lets say you have a TCP/IP network and ARIN or your ISP (Internet service provider) has assigned your IP network address and default classful mask. When you look at the four bytes of an IP address, the first byte determines the class. If you have a network address of 130.57.0.0 with the default mask of 255.255.0.0, you have a Class B address with a network capable of supporting more than 65,000 hosts. You probably wont need a network with more than 65,000 hosts; instead youll want to subdivide your network into smaller, more manageable pieces called subnets connected through gateways. Subnetting is breaking up larger networks into smaller networks. Take the example of a pie. If you are given a whole pie, chances are you will not want to eat it all. Instead, you slice the pie into pieces and use what you need. Just like the pie you slice, you can borrow bits from the host side and add them to the network side, which creates a subnet. You need to keep four things to keep in mind if you want to evenly break up a larger network: How many subnets are presently required for the organization? How many additional subnets will need to be provided for in the future? What is the number of hosts in the networks largest subnet? What is the anticipated size of the largest future subnet on the network? To understand the process of breaking up a network, consider breaking up a 130.57.0.0 network address with the default network mask of 255.255.0.0. If you want to subnet the network you borrow from the host bits and add them to the network side. For example, lets say you need 254 subnetworks within your network. To achieve this you would need to borrow 8 of the host bits and use them for subnets within network 130.57.x.0 (x represents the 8-bit byte you are borrowing). This changes your mask of 255.255.0.0 to a subnet mask of 255.255.255.0. In Figure 2.10 the network 130.57.0.0 has been broken up into several subnetworks by borrowing all 8 bits within the third byte and masking them off. From there, you need to identify the network IDs for each new subnet such as 130.57.1. Now instead of one network, you have a total of 254 usable subnets. You can continue to borrow bits to increase the number of subnets and decrease the number of hosts. Although this example shows only 2 subnets, network 130.57.0.0 now can support a total of 254 subnets, providing for future growth. With 1 byte left over for hosts, each of these subnets could support up to 254 hosts. When you vary the length of the default network mask beyond the default classful boundary, it is referred to as VLSM (variable length subnet mask). Some routing protocols do not understand VLSMs and thus have difficulty routing datagrams destined to subnets that they cannot discover. We discuss routing in Chapter 5, IP Routing and routing protocols in Chapter 6, Routing Protocols.
45
FIGURE 2.10
Subnetting a Class B network.
Class B Network Router
130. 57 .0.0 255.255.0.0
130. 57. 2 . 0 255.255.255. 0 130. 57. 1. 0 255.255.255.0

Net # Sub- Host Net# IDs Net # Sub- Host Net# IDs
To figure out how many bits you need to borrow, you first need to know how many subnets are needed within your network. For this example, lets say you need 13 additional subnets for a Class C network address of 192.3.1.0 with a default mask of 255.255.255.0. To calculate the number of bits required for a specific number of subnets use the chart in Figure 2.11. To determine the number of bits to borrow: 1. Start from the right. 2. Cover bits with a your hand or a piece of paper until you reach a value that is at least 2 greater than the number of subnets you need.
FIGURE 2.11 IP Calculation Chart
65536 . 32768 16384 8192 4096 2048 1024 512 256 . 128 64 32 16 8 4 2 1 X . X X X X X X X X . X X X X X X X X
Use this chart to determine how many bits are required for subnets and hosts.
46
TCP/IP PRIMER PLUS
3. Take that number and subtract 2 (subtracting 2 from the number eliminates 2 bit values that are all 1s and all 0s, which are invalid). 4. The resulting value represents the number of subnets you get if you borrow the bits you covered. For instance, for 13 subnets: 1. Cover the following bits from right to left 4, 2, and 1. 2. You should see a value of 8 in the next bit position. 3. Subtract 2 from 8, which equals 6; with 3 bits you do not get enough subnets. 4. Cover one more bit so you have covered 4 bits total. 5. Look at the next value, 16 (this is at least two greater than the 13 subnets you need). 6. Subtract 2 from 16, which equals 14. 7. You now have enough for the required 13 subnets (see Figure 2.12). You can use the same calculation chart and method to calculate the number of bits necessary for hosts. Note that when you have a finite number of bits to be shared between subnets and hosts, bits you use for one cannot be used for the other. For example, if you have 16 bits available and you borrow 7 bits for subnets, you have only 11 bits for hosts. If you borrow 12 bits for subnets you have only 4 bits for hosts. Its simple math. You can use the chart to determine how many subnets you will get with 7 or 12 bits and how many hosts you will get with 11 or 4 bits using the earlier method.
FIGURE 2.12
How Many Bits do I need to borrow if I want 14 Subnets? 27 128 X 64 X 32 X 16 X 8 X 1 4 X 1 2 X 1 20 1 X 1
In this example you need to borrow 4 bits.
8 + 4 + 2 + 1 = 15 15 - 1 = 14 Subnets
Now that you have determined you need 4 bits to have 13 subnets, you need to extend the network mask to include the subnets; that is, the 4 subnetted bits (subnet mask). You know the default classful mask for network 192.3.1.0 is 24 bits in length or 255.255.255.0, so you leave these bits alone. To determine the subnet mask:
47
1. Start from the leftmost bit within the last byte (the 25th bit, and so forth). 2. Count from left to right 4 bit positions. 3. Add up the bit values of the four bit positions you counted off: 128+64+32+16=240 (see Figure 2.13). 4. The subnet mask for 14 subnets equals 240. The standard Class C network mask changes to include subnets within the last octet, making your new network and subnet mask 255.255.255.240. You now have 14 usable subnet addresses with 4 bits left over for hosts on each of the subnets.
FIGURE 2.13
What is my Mask for the last byte? 27 128 X 1 64 X 1 32 X 1 16 X 1 8 X 4 X 2 X 20 1 X
To figure the subnet mask, add up the masked bits to calculate the mask value.
128 + 64 + 32 + 16 = 240 4 bit Mask = 240
You also need to identify the available subnet range within the 240 subnet mask. There are two ways to calculate the subnet range; one is to list all the possible combinations of subnetted bits as in the following: 1. List all bit combinations with the 4 bits reserved for subnet addresses. 2. Add the charged bits for each unique bit combination that falls within the subnet masked portion. Again, remember to throw out the combinations of all 1s and all 0s. 3. Place 1s and 0s under the different combinations of high order values (see Figure 2.14). 4. Add up the different combinations. 5. You should have 16, 32, 48, 64, 80, 96, 112, 128, 144, 160, 176, 192, 208, and 224, respectively. These 14 numbers represent your subnetwork addresses (see Figure 2.14). The other way to calculate the subnet range is as follows: 1. Use the lowest value in the masked range (16, start of range) as your base value. This represents the first valid subnet. You can figure all other subnets with this base value. 2. Continue to add 16 (the difference between each range) to these numbers until you reach the highest value below the mask. These numbers create your subnet range. 3. For example, add 16 to 16 (32). Add 16 to 32 (48). Your next subnet range should equal 64.
48
TCP/IP PRIMER PLUS
FIGURE 2.14
What is the Subnet Range?

240 128 64 32 16 X 0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 X 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 X 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 X 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 8 X 4 X 2 X 1 X
This subnet range. Remember that all 0s and all 1s are illegal.
You now must figure the number of hosts per subnet. Different classes and a different number of bits borrowed affect the number of hosts per subnet. Because you borrowed 4 of the 8 bits within the last byte for subnets, you have only 4 bits left over for host assignment. You already know the calculation for 4 bits; it is the same calculation you did for subnets. To figure the number of hosts per subnet (host range): 1. Start from the low order bit and move to the left. Cover the 4 bits you have left to use for hosts. 2. Look at the next uncovered value (16). 3. Subtract 2 to find out how many hosts you get with the remaining four bits. Of course you already know the answer to this question because you did the math for subnets (162=14 hosts per subnet). 4. For valid host IDs on each subnet, add 1 to each starting subnet range (for example, 16+1) and subtract 2 from the next value in the subnet range (for example, 322). 5. Continue this process for each subnet range to get the values of the valid hosts for each subnet. 6. You should have 1730, 3346, 4962, 6578, 8194, 97110, 113126, 129142, 145158, 161174, 177190, 193206, 209222 and 225238 as your valid ID ranges (see Figure 2.15). Note that the broadcast value for each subnet is 1 less than the next valid subnet value. For example, the broadcast address for subnet 16 would be 31 (321, as 32 is the next subnet).
49
FIGURE 2.15
Valid Host and Broadcast Addresses

240 128 64 32 16 X 0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 X 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 X 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 X 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 17 33 49 65 81 97 113 129 145 161 177 193 209 225 8 X 4 2 1 Broadcast 31 47 63 79 95 111 127 143 159 175 191 207 223 239 X X X Host Range 30 46 62 78 94 110 126 142 158 174 190 206 222 238
This figure shows the valid ID ranges.
As previously mentioned, class type affects the number of host bits available for borrowing. The good news is the calculation procedure does not. Lets take a look at a Class B address. For a Class B address with a standard 16-bit network mask (255.255.0.0) with an additional 4 subnetted bits, you can see that you have 12 host bits available to borrow. We already did the math on 4 bits. We know that 4 bits will get you 14 (subnets or hosts), depending on what you are using the bits for. With that information we know how many bits we need to extend the Class B default mask: 4 additional bits to include the subnets. That changes the mask to 255.255.240.0. We have extended the mask to include 4 bits within the third byte as subnetted bits. This means we have 12 bits left over within the third and fourth bytes to assign hosts. Use the calculation chart to find out how many hosts we will get per subnet with 12 bits. Cover all 12 bits with a piece of paper and look at the next uncovered value, which should be 4096. Subtract 2 (40962= 4094) to determine the number of hosts per subnet (see Figure 2.16). Earlier you learned how to derive the subnet range from a Class C network with 4 subnet masked bits. With 4 subnetted bits you get this subnet range: 16, 32, 48, 64, 80, 96, 112, 128, 144, 160, 176, 192, 208, and 224, respectively. These 14 numbers represent your subnetwork addresses. Now that you know the subnet range, you identify the valid host IDs and broadcast address on each subnet. This is where you deviate from the previous method. With a Class C example, as previously used, you had only 8 bits to worry about; now you have 16 bits to deal with.
50
TCP/IP PRIMER PLUS
FIGURE 2.16
12 bits for hosts MASK 255
The Class B network 130.100.0.0 has been further divided into subnets by masking off four of the host bits within the third byte (240).
. . .
255
240 16
. . .
0 XXXXXXXX
XXXXXXXX
XXXXXXXX XX X X XXXX . 100
130
Class B Network ID 4 subnet bits = 14 subnets 12 host bits = 4094 hosts per subnet
4 Subnet Bits
With a Class B network, when you cross over an 8-bit boundary, such as this example (network 130.100.0.0 255.255.240.0 mask, representing the 4 subnetted bits in the third byte) in which the host bits straddle the third and fourth bytes, calculating the host ranges gets a little more complex. The best method of tackling this is to use binary. To calculate the host range: 1. Take the first subnet within network 130.100.16.0 (the lowest subnet within the mask) and convert it to binary. 2. Start with the lowest possible value within the host ID bits. This gives you the first valid host within the subnet. 3. Identify the highest possible value (which represents the broadcast for the subnet). By doing this you can easily back into the highest valid host range within the subnet (which is always one less than the broadcast). 4. When you cross over an octet boundary, you add the values in each octet separately. Remember to add only the charged bits within each byte. 3rd byte . 4th byte 4bit mask 240 128 64 32 16 | 0 0 0 1 | 8 0 4 2 0 0 1 0 . . 128 0 64 32 16 0 0 0 8 0 4 0 2 0 1 1
5. To identify the first valid host address on subnet 16, place 0s in all host bit positions except the rightmost bit, which is a 1. This represents the lowest possible host value available within this subnet. Remember you cannot have all 0s in the host portion (invalid host ID). 6. Take each byte separately and add the charged bits within the byte. The third byte contains only 1 charged bit, 16; therefore, the value within that byte equals 16.
51
7. The fourth byte contains only the last byte charged bit, which is a value of 1. Your first valid host IP address for subnet 16 on network 130.100 would be 130.100.16.1 (see Figure 2.17).
FIGURE 2.17
What is the First Valid Host for each Subnet?
240 Sub 128 64 32 16 nets X X X X 16 32 48 64 80 96 112 128 144 160 176 192 208 224 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 8 X 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4 X 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 X 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 128 64 32 16 8 4 X X X X X X X 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 First Valid Host 16.1 32.1 48.1 64.1 80.1 96.1 112.1 128.1 144.1 160.1 176.1 192.1 208.1 224.1 X X
This figure shows how to calculate the first valid host for each subnet.
Now go to the opposite extreme to derive the broadcast address. Change all 12 host bits to 1s; then add the charged bits within the third and fourth bytes separately (see Figure 2.18). 3rd byte . 4th byte 4bit mask 240 128 0 64 32 16 | 0 0 1 | 8 1 4 1 2 1 1 1 . . 128 64 32 16 8 1 1 1 1 1 4 1 2 1 1 1
Broadcast 130.100.31.255You get this by adding all charged bits within the third byte; then the fourth byte. You have 16+8+4+2+1=31 in the third byte. From here you can easily determine that highest possible valid host ID, which is always one less than the broadcast address for the subnet. To determine this, just change the rightmost bit to a 0; then add them up again. You have 130.100.31.254 as your last valid host range (see Figure 2.19). 3rd byte . 4th byte 4bit mask 240 128 0 64 32 16 | 0 0 1 | 8 1 4 1 2 1 1 1 . . 128 64 32 16 8 1 1 1 1 1 4 1 2 1 1 0
52
TCP/IP PRIMER PLUS
FIGURE 2.18
What is Broacast address for each subnet?

240 Sub 128 64 32 16 nets X X X X 16 32 48 64 80 96 112 128 144 160 176 192 208 224 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 8 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 128 64 32 16 8 4 X X X X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Subnet Broadcast 31.255 47.255 65.255 79.255 95.255 111.255 127.255 143.255 159.255 175.255 191.255 207.255 223.255 239.255 X X
The broadcast address is indicated by all 1s in the hosts bits.
FIGURE 2.19
What is the Last Valid Host for each Subnet?

240 Sub 128 64 32 16 nets X X X X 16 32 48 64 80 96 112 128 144 160 176 192 208 224 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 8 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 128 64 32 16 8 4 X X X X X X X 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 X X 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 31.254 47.254 65.254 79.254 95.254 111.254 127.254 143.254 159.254 175.254 191.254 207.254 223.254 239.254 Last Valid Host
As you can see, the last valid host within a subnet is always 1 less than the broadcast, indicated by a value of 0 in the rightmost (value of 1) bit position.
Supernetting, Summarization, Aggregation, and CIDR

The networking industry throws around the terms supernetting, route summarization, route aggregation and CIDR (class interdomain routing) on a regular basis as if they were completely different technologies. However, these terms do not merit a distinction as separate technologies. In reality they all describe a method of reducing route update traffic and routing tables by condensing a group of contiguous IP addresses into a single address representative of the entire group.
53
Whichever term you decide to use, it enables routers to advertise a subset of routes reducing the number of route updates that need to be sent and reducing the size of route tables. Im most comfortable with the term summarization, so Ill use it throughout this section and book in describing the process. Even though summarization might seem like a foreign concept, believe it or not youre already implementing it in your network. If you have a network that has been assigned a registered IP address to connect to the Internet, the address ARIN or your upstream service provider assigned to you represents the summarization of your companys network to everyone on the Internet. The ARIN organization through its classful addressing scheme deliberately defined Class A, B, and C addresses which, if defined with one summarized address and assigned to a company, represent the company and all of the internal subnets. Of course you could advertise to the entire world all of your internal subnets through the Internet; however, I do not advise this for two reasons: Its an obvious security issue, and its not necessary. You do not need to do this because to get to your network and its subnets, other routers within the Internet need to know only how to get to your major unique classful network assigned by ARIN. Once traffic destined for network reaches your local gateway, this gateway and the gateways internal to your companys networks take care of the rest. Consider the additional route update traffic that would be required to advertise all of your routes, and the resources it would take for all routers on the Internet to keep track of all networks and subnets for every network in existence. This is why summarization is so important. You also can implement summarization within your companys routing infrastructure to reduce the amount of route update traffic and routing table sizes. Typically you perform summarization on routers connecting to a companys core, where link congestion and bandwidth capacity are important issues. By summarizing multiple IP addresses into a single address before this information is sent into the core you can reduce update traffic, conserving precious bandwidth.
CIDR
The industry tends to use the term CIDR to describe route summarization performed on contiguous Class C addresses. This type of summarization typically is done by ISPs or service providers, which have been assigned a group of contiguous Class C addresseswhich they in turn have given to their downstream clients.
ISPs and Service Providers

Most of the time the terms ISP and service provider can be used interchangeably. However, the term ISP describes a company that provides Internet service (thus, the name Internet Service Provider) and only Internet service. A service provider can provide Internet service (an ISP) as well as other services that an ISP does not provide, such as Frame Relay and WAN connections.
54
TCP/IP PRIMER PLUS
The provider knows the Class C address of each client representing its network. The ISP can advertise each of the Class C network addresses out to the Internet or a subset of them. It might summarize several of these addresses into a single address to reduce the route information it passes to other gateways on the Internet. Summarization of a group of addresses can be performed only when the addresses being summarized are contiguous and can be summarized only on a power of 2 boundary. Lets take the following IP addressing example and perform summarization: You have a Class B network address assigned to your organization (130.100.0.0, default mask 255.255.0.0) with many internal subnets. Look at a subset of these subnets for simplicity. You have x number of IP addresses that are contiguous; instead of advertising each of these separately, you want to group them and advertise the summarized route. You would 1. Convert the IP addresses in question to binary (see Table 2.2). 2. Move from left to right. 3. Look for the longest binary match (or common bit pattern) within each address; this represents the IP address for summarization.
TABLE 2.2 IP Address
Route Summarization
Mask 128 64 Binary Representation 32 16 8 4 2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
130.100.16.0 130.100.17.0 130.100.18.0 130.100.19.0 130.100.20.0 130.100.21.0 130.100.22.0 130.100.23.0 130.100.24.0 130.100.25.0 130.100.26.0 130.100.27.0 130.100.28.0
255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0
0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0
55
TABLE 2.2 IP Address
Continued
Mask 128 64 Binary Representation 32 16 8 4 2 0 0 0 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 1
130.100.29.0 130.100.30.0 130.100.31.0
255.255.255.0 255.255.255.0 255.255.255.0
0 0 0
0 0 0
You really dont need to do a binary conversion to determine whether they match because each address starts with 130.100, so the binary match would be identical. In this case only the third byte is in question. Now that you have the list of binary values for each subnet, its clear that all of these subnets have the first 4 bits in common, in addition to the 16 bits within the first and second bytes. This means you can summarize all of these subnets with a single IP address of 130.100.16.0 using a 20-bit mask (16 networks bits plus 4 subnet bits) or 255.255.240.0 or /20. Remember the point of summarization is to reduce route updates. You might have recognized that subsets within this group all contain further matches. However, only those addresses that match exactly can be summarized and only to the longest match. You could group the subset of matches and summarize them separately; however, you would need to advertise that group separately. Because all 16 of the previously mentioned networks have 4 common bits you can group and summarize all 16 of them with a single address. Summarizing a subset proves less efficient and unnecessary.
Implementing Route Summarization

The implementation of route summarization within your network requires configuration of routers, which is vendor specific and beyond the scope of this book.
Network Address Translation (NAT)

The term network address translation describes the process of translating nonregistered (private) IP addresses (listed earlier in this chapter) to a single registered valid IP address or range of addresses to be used when communicating with hosts on the Internet. Remember that ARIN is responsible for assigning registered IP addresses to organizations for use on the Internet. However, the 32-bit addressing scheme it developed way back when cannot support the millions of Internet hosts in existence today. To address the issue of dwindling IP addresses and the exponential growth of Internet hosts, new IP addressing solutions became necessary. The networking industry proposed one solutionto change the current IP addressing scheme, increasing the number of Network layer bits from 32 to 128, making more addresses available. The industry has discussed this new addressing scheme, referred to as
56
TCP/IP PRIMER PLUS
IPNG (NG stands for next generation, which I assume was named by some Trekkies out there in the virtual galaxy). IPv6 (v6 meaning version 6). The current version of IP is version 4. Although the industry has debated IPv6 regularly, this option has been largely ignored because it would require everyone participating on the Internet to redesign their addressing schemes. In addition, adjustments would have to be made to current routing protocols, and so on, to effectively implement it. Meanwhile, other solutions have emerged that enable us to continue using the existing addressing structure of IPv4, such as NAT. An administrator must enable and configure a router with the NAT service (specific configuration is beyond the scope of this book). Routers supporting NAT basically convert inside private addresses, such as 10.x.x.x to a registered outside IP address, when a host within the private network attempts to communicate with a host on the Internet. NAT has three types of implementation: Static (see Figure 2.20) Dynamic (see Figure 2.21) Combination of static and dynamic
FIGURE 2.20 Static Mappings
NAT Table Inside Private Outside Registered
This shows a one-to-one (static) mapping of the inside to the outside address.
10.1.1.2
36.1.2.3
10.1.1.3
36.1.2.4
FIGURE 2.21
Dynamic Mappings
Client Port
This shows multiple private addresses mapping to the same outside registered address using different port numbers (dynamic).
Inside Private
Outside Registered:
10.1.1.2
36.1.2.3
1004
10.1.1.3
36.1.2.3
6002
57
Static
Think of static NATs as one-to-one network translationseach inside address is mapped to a different outside address. Administrators must manually create the static mapping on the router performing the translation. With this type of NAT you must have as many outside addresses as inside, which makes NAT seem useless.
Dynamic
Think of dynamic NATs as many-to-one or many-to-a-couple network translationsmultiple inside addresses mapped to a single outside address or small pool of addresses. Administrators typically define a small pool of registered addresses to be used when translating any inside address. Because a single IP address or small pool of addresses is used to translate all inside addresses, an administrator must implement a method of uniquely identifying each inside host. To uniquely identify each inside host, even though they map to the same outside address, the source hosts Transport layer port (identifying the process or program) is appended to the outside address. The industry uses this type of NAT the most. With this type of NAT, you need only one or a couple of outside addresses, making the most efficient use of the registered addresses. Routers performing NAT maintain mapping tables to keep track of the mapped addresses. When an inside host wants to send a datagram to a host outside the private address, it sends the datagram to the gateway for forwarding. The router maps the inside address to a registered outside address using one of the methods previously mentioned and forwards the datagram. It then holds the mapping in memory for later use (see Figure 2.22).
FIGURE 2.22
Internet Outside Router Private Network Inside
This figure shows the router holding the mapping for the private addresses to the same outside address in memory.
Inside Private 10.1.1.2 10.1.1.3
Outside Registered: 36.1.2.3 36.1.2.3
Port 1004 6002
Once the router has mapped the inside address to an outside address, it uses this address within the IP header of the datagram, indicating the source or sending host. The destination
58
TCP/IP PRIMER PLUS
host does not know that the sending hosts address is actually a translated address, nor does it care. When the destination host responds to the source host, the router remaps the outside address to the inside address and delivers it to the original host. Because translation is transparent, you can effectively hide your inside network hosts and infrastructure from the outside world and still allow them to communicate.
Summary
The base-10 numbering system, known as decimal numbering, consists of the numbers 0, 1, 2, 3, 4, 5, 6, 7, 8, and 9. Computers use the binary, or base-2 numbering system. To understand binary numbers, we convert them to the decimal. The Network layer controls routing and where to route traffic. These decisions stem from the 4-octet, or 32-bit, IP address. The network address represents a companys network and subnetwork (a major network) and a node address represents a specific device on that network. There are five major address classes: A, B, C, D, and E. The public uses only Classes A, B and C. Subnet masks help routers and end hosts determine how to route datagrams. If the destination host resides on the same local segment, it can send an ARP broadcast to resolve the logical Network layer IP address to a MAC address. If the destination is remote, it routes the datagram to a local gateway router. The process of comparing the destination hosts IP address to the sending hosts subnet mask is called bitwise ANDing. Summarization enables routers to advertise a subset of routes. This reduces the size of the routing tables and the number of route updates that need to be sent.
Review Questions
1. What are the various IP address classes and their ranges? 2. What purpose do subnet masks serve? 3. What is the difference between the network address and the node address? 4. What are the restricted addresses and for what are they used? 5. How many bits in a Class C address are used to define the network number? 6. With a network address of 193.1.1.0 and a subnet mask of 255.255.255.240, how many subnetworks are available and how many hosts per subnet? 7. If you have an IP address of 193.1.1.32 and a /28 subnet address, what would the subnet mask be?
59
8. What is the correct number of subnets and hosts available on a Class B network with a subnet mask of 255.255.254.0? 9. On a Class C network, how many bits would you need to borrow if you needed 19 hosts? 10. On a Class B network, how many bits would you need to borrow if you needed 1000 hosts? 11. What is the decimal equivalent of the binary 10110111? 12. What is the binary equivalent of a subnet mask of 201?
CHAPTER 3
NETWORK LAYER/INTERNET PROTOCOLS

IP operation, fields and functions Fragmentation and reassembly of datagrams ICMP messages and meanings
IP
IP (Internet Protocol) does most of the work in the TCP/IP protocol suite. All protocols and applications within the TCP/IP suite run on top of IP and utilize it for logical Network layer addressing and transmission of datagrams between internet hosts. IP maps to the Internet layer of the DoD and to the Network layer of the OSI models. ICMP (Internet Control Message Protocol) is considered an integral part of IP and uses IP for its datagram delivery; we will discuss ICMP later in this chapter. Figure 3.1 shows how IP maps to the DoD and OSI models.
How Do I Buy a Ticket on the IP Train?

The phrase runs on top of might sound as if an application or protocol is buying a ticket to ride on an IP train. This term is not restricted to IP. In reality, it is industry jargon used to describe any upperlayer protocol or application coming down the OSI model and utilizes another lower-layer protocols features (in this case IP at the Network layer).
IP provides an unreliable, connectionless datagram delivery service, which means that IP does not guarantee that an IP datagram successfully reaches its destination; rather it provides best effort of delivery, which means it sends it out and hopes it gets there. IP simply adds logical source and destination network layer addresses and delivers the datagram relying on other layers to guarantee it gets to its destination. If there is a problem with delivery, IP relies on ICMP to send messages when it encounters an error. When IP encounters an error in delivery, it simply trashes the datagram, causing an ICMP message to be sent to the source host detailing what kind of delivery problem occurred. IP relies on upper layers to provide reliability; for
62
TCP/IP PRIMER PLUS
example, TCP (which will be discussed in more detail in Chapter 8, Transmission Control Protocol (TCP)).
FIGURE 3.1
DOD
Process/ Application Host-to-Host Transport Internet Network Access
OSI
Application Presentation Session
IP provides logical addressing and connectionless delivery of datagrams for all protocols within the TCP/IP suite.
IP, ICMP
Network Data Link Physical
The Internet Protocols primary function is logical network layer addressing of hosts and delivery of information in the form of datagrams between hosts. IP addressing is discussed in detail in Chapter 2, IP Addressing. IP also performs other important functions such as fragmentation and reassembly, which are necessary when datagrams are too large to be sent by a source host and must be broken up into smaller datagrams. Because IP is connectionless it does not require a connection between hosts. It does not sequence, acknowledge, or control the flow of data between hosts. IP treats each datagram as a separate entity; it merely addresses the datagram and sends it out, hoping it reaches the destination. IP receives a stream of data from UDP or TCP, breaks up this information into chunks, and addresses and packages each piece as a datagram, which then can be sent to a destination host across the network. Routers and routing protocols determine the path selection between a source and destination, which we discuss in more detail in Chapters 5, IP Routing and 6, Routing Protocols.
RFC 791
RFC 791 defines IP, and its fields and functionality. In this chapter we will look at an IP header and its fields and examine the other protocols that reside on the Internet layer. We will discuss IP routing in Chapters 5 and 6.
IP Header
Figure 3.2 shows the format of an IP datagram as defined by RFC 791. An IP header contains a minimum of 20 bytes, unless options are present. Figure 3.3 shows an IP header as seen through a Sniffer protocol analyzer. We will describe each field after the figures.
Chapter 3 NETWORK LAYER/INTERNET PROTOCOLS
63
FIGURE 3.2
The Internet Protocol header provides for identification of logical source and destination network addresses.
Version
IHL
Type of Service Flags
Total Length Fragment Offset Header Checksum
Identification TTL Protocol
Source Address Destination Address Options Padding
FIGURE 3.3
Note the Ethertype value contained within the DLC (Data Link Control) header states that protocol type 0x0800 or IP is the protocol being carried within this frame.
Take a look at the IP header in Figure 3.3. The first field is the version type, which should always be version 4, the official standard. This is followed by the header length, indicating the size of the IP header as 20 bytes. Type of service (ToS) values follow. Most often the ToS value, as in this case, will have a value of zero because ToS is seldom used. However, this trend is changing as ToS becomes more understood and more vendors implement it successfully in their products. New applications capable of setting these bits to influence a routers routing of datagrams are emerging. This allows them to request from routers a certain level of ToS service for transmitted data. The total length of the datagram is 40 bytes, which includes the IP header and data being carried within the frame. The IP ID value given to this datagram is 25276. Note that in the Flags field the datagram can be fragmented if necessary, and that this is the last fragment. Because the fragment offset has a value of zero, we can deduce that this is the first, last, and only fragment within the stream.
64
TCP/IP PRIMER PLUS
The TTL value currently is set to 59 seconds, which is the amount of time left for this datagram to live on the internetwork. The next protocol being carried within the frame is TCP. IP uses the checksum value to identify frame damage. The sending hosts logical IP address is 36.56.0.152 and the destination hosts address is 36.53.0.203.
Version
The value within the 4-bit version field identifies the version of IP being implemented. This value will always be version 4. It is the most current and popular version of IP.
Internet Header Length

The 4-bit header length field identifies the size of the IP header in 32-bit words. All IP headers must have a minimum of 20 bytes in size unless additional options are implemented and specified within the option field, which we will discuss later in the Type of Service section of this chapter.
Type of Service
The ToS bits (8 total bits) within the IP header can influence the path datagrams take when being forwarded by routers from source to destination. ToS bits allow upper applications and processes to indicate the type of quality or service they require from a router. Until recently, the use of the ToS bits has been nonexistent. However, many companies now implement them to facilitate more intelligent path selection. If ToS has not been implemented, this field will have a value of zero. Because the use of ToS is uncommon, zero is an expected value. RFCs 1340 and 1349 describe the specific use and functions of these bits. The following explains the various ToS bits.
Bits 02: Precedence Bits

Bits 02, known as precedence bits, when used in the following combinations mean different things, and typically only the government uses these implementations to define the importance of a datagram. This value uses the options field within the IP header, discussed later in this chapter, to further describe the type of precedence requested. The precedence value typically describes the type of security levels requested defined by the Defense Intelligence Agency. Table 3.1 describes the various precedence bits set.
TABLE 3.1 Bit Position 000 001 010 011
Bits 02 = Precedence
Description Routine information Priority information Immediate delivery Flash
65
TABLE 3.1 Bit Position 100 101 110 111
Continued
Description Flash override Critical information Internetwork control Network control
Until recently most applications did not support or use precedence bits. However, they comply with governmental network implementations, which require multilevel security functions. No further discussion of these bits will follow. Precedence is described in further detail in Chapter 8. The organization that chooses to implement these bit must specifically define the precedence bits, and their use and meanings. The next three ToS bits are the most commonly used for influencing traffic patterns.
Bit 3
Bit 3 can have one of two values: 0 = Normal delay 1 = Low delay Delay is based on the end-to-end propagation delay of data transmitted over a link. When multiple paths exist to a destination, an application can direct routers en route to select the path with the least delaya faster path.
Bit 4
Bit 4 can have one of two values: 0 = Normal throughput 1 = High throughput When an application requires a path to a destination that offers high throughput rates, it sets the throughput bit to 1. Routers forward traffic along paths that support the highest possible data rate, measured as the bandwidth capacity of a link between source and destination.
Bit 5
Bit 5 can have one of two values: 0 = Normal reliability 1 = High reliability Routers measure a links reliability by the number of errors encountered and lost datagrams it experiences when forwarding or receiving across an interface. If multiple paths exist and one
66
TCP/IP PRIMER PLUS
appears to be more reliable than the other, a router forwards traffic for applications, setting the reliability bit to 1 across this interface. Critical applications that cannot tolerate data loss may request this type of service.
Bits 6 and 7 (Reserved)

Bits 6 and 7 are reserved and not currently used. Upper-layer applications or processes can request for routers to deliver their data along paths that meet their service requirements. For ToS delivery to work all routers and routing protocols within the path from source to destination must understand, and be configured to forward datagrams based on the ToS designation. Not all routing protocols understand these bits. The following routing protocols understand ToS: OSPF EIGRP IGRP BGP The following protocols do not understand ToS: RIP v1 RIP v2 Although a routing protocol might have the capability to understand and act upon these bits, it still requires configuration. If someone has not configured the router to support ToS, it simply ignores this information and forwards the datagram the best it can. Lets look at an example of how ToS works. When an application requests datagrams to be sent through a low delay path, it sets bit 3 to a value of 1. Routers along the path attempt to send datagrams across links offering faster transmissions, such as 100Mb Ethernet versus slower WAN links. Keep in mind that delay is measured by the round-trip propagation delay across the link. Therefore, a link with a lower delay would be the preferred path. High throughput translates to high-capacity links, which have the capability to carry larger amounts of data in a shorter time frame. This is useful for large file transfers. Routers measure the capacity of a link in terms of bandwidth, which is the transfer rate in bits across the interface. For example, an Ethernet 100Mbps link carries 100 million bits per second, which is faster than a 10Mbps (10 million bit per second) interface. If reliability is the objective, such as the case in an application performing critical processes or requiring security, an application can request a more reliable transmission path by setting bit 5 to a value of 1. This might be a transaction-based processing application, which requires access to a companys fault-tolerant backbone. It is very important to understand that by setting these bits, you change the way routers route traffic. Without a thorough understanding of the types of protocols, applications, traffic flows and protocol timers within your network, this manipulation could have catastrophic results. It is imperative that you baseline your network thoroughly before attempting to implement
67
them. When properly used, they can dramatically increase the performance of your network and network applications.
Total Length
The 2-byte total length field within the IP header defines the length in bytes of the entire IP datagram. This value includes the IP header and data being carried within the datagram.
Identification
The sender gives each IP datagram an ID value prior to transmission, which is found in the 2byte identification field. This ID uniquely identifies a datagram or stream of datagrams. The destination host uses this ID to reassemble the datagrams received. When a source hosts IP process receives a large stream of contiguous data from UDP or TCP for datagram packaging, it breaks up this stream (fragmentation) when it receives a packet that is too large for the transmission medium. IP then assigns all datagrams belonging to the stream the same ID. When transmitted from source to destination, datagrams can take different paths with widely varying characteristics, causing them to arrive out of order. The destination host uses this ID to recognize that all the datagrams belong to a stream. It then reassembles them in the correct order based on the fragment offset value, which we will explain later in this section.
Flags
Bit 0 = Reserved. Must be a value of zero. Bit 1 = Can have one of two values: 0 = May Fragment 1 = Dont Fragment The 3-bit flags field is used on hosts and gateways for fragmentation purposes. If a host or a gateway supports fragmentation, it can break a stream of data into smaller pieces before transmission. If it does not support fragmentation (the dont-fragment bit is set), the host or gateway cannot fragment the stream. Typically, the sending host has the responsibility of performing fragmentation. The destination host reassembles the datagrams into the original stream before passing it up to the upper layer (TCP or UDP) for processing. However, this is not always the case. When a source host sends a datagram that reaches a segment and is too large to be forwarded, the gateway performs the fragmentation, breaking the datagram into smaller units acceptable for the media. Having intervening gateways perform fragmentation of datagrams in transit is not a good idea. Routers forced to perform this function require additional resources and add unnecessary overhead and latency to the delivery of the datagram. Because different underlying network architectures support varying frame sizes, find out what the lowest value MTU (Maximum Transmission Unit) size is for your network and configure your hosts and gateways to support it. For example, Ethernet has a maximum frame size of 1518 bytes, whereas TokenRing frames might range from 4,500 bytes to 17,800 bytes.
68
TCP/IP PRIMER PLUS
The DF bit has another use. Some implementations use the DF bit to dynamically discover the MTU size of the network end to end. If intervening routers have this bit enabled, when an end host attempts to send a datagram that is larger than the next segment along the transmission path, the router will not forward the frame. Instead, the router drops the datagram and kicks back to the source host an ICMP message indicating the datagram is too large and has exceeded the maximum segment size. The host then can use this information to resize its next datagram. This process will continue until the sending host has discovered the proper size to send, allowing intervening routers to simply forward datagrams without performing fragmentation en route to its destination. Bit 3 = Can have one of two values: 0 = Last Fragment 1 = More Fragments The Last or More Fragments bit indicates whether this is the last datagram within a stream or more datagrams are to follow. If there is only one datagram this bit will be zero, indicating that this is the first and the last, meaning it is the only one. When a destination host receives a datagram, it notes the ID value and checks whether this bit is a one or zero, indicating that this is the last datagram or more are expected. If it expects more, this host holds the datagrams in memory until all others with the same ID arrive and the stream is reassembled and passed up to the appropriate upper-layer protocol for processing. By matching the IDs and referencing the last or more bit, the host knows when to stop expecting future datagrams within this stream and when to start reassembling them.
Fragment Offset
The sending host uses the 13-bit fragment offset value to identify the position of the datagram with the stream being sentthe order in which this datagram belongs when more than one is sent with the same IP identification. The sending host always assigns the first datagram with an offset value of zero. It assigns the second, third, or more datagrams with a number based on the MTU size. The receiver uses the fragment offset value to put the datagrams within the same stream back together upon reception or detect that one is missing within the stream. For example, if a sending host has three datagrams to send that belong to a stream, it goes through this process: 1. Assigns each of these datagrams the same ID. 2. Sets the More Fragments bit to a one on the first two datagrams to indicate that these are not the only datagrams in this stream and that more are to follow. 3. Sets the Last Fragment bit on the final datagram in the stream. 4. Each datagrams offset bears an offset value identifying where this datagram belongs in the stream. Figure 3.4 shows an example of a sending host and a receiving host using the fragment offset value to determine in what order datagrams belong. In Figure 3.4 Station A wants to communicate with Station B and sends a single datagram containing 1500 bytes of information on the
69
wire. Note that the local segment attached to segment A can accept a maximum transmission unit (MTU) size of 1,518 bytes, which is sufficient to support this frame size. The datagram makes it through Router 1, which forwards it on to Router 2 as is. Note that the segment between Router 1 and 2 also accepts an MTU of 1,518. In Figure 3.4 the WAN segment between Routers 2 and 3 will not accept a segment larger than 512 bytes, so Router 2 must break up the original datagram sent by Host A to fit this datagram on the wire; this is called fragmentation. There now are three datagrams forwarded across this link to Router 3 and ultimately to their final destination, Host B. Once these datagrams reach Host B, this host performs the reassembly prior to sending them up to the upper-layer process. Host B (the receiving host) uses the IP identification field, Last and More Fragments bit, and the fragment offset to piece the datagram back together.
FIGURE 3.4
Fragmentation and Reassembly
In this figure, Host A sends a 512-byte datagram, which is too large for the WAN. Router 2 breaks up the datagram (fragments) into smaller chunks, forwarding them. The destination host is responsible for reassembly.
1500
MTU=1518 bytes MTU=1518 bytes
R2
1024
R1 1500
Network MTU=512 bytes
512 0
1500
512 0 1024
R3
Using Figure 3.4 as an example, the receiving host expects to find and reassemble the datagrams in the following order: 1. The first datagram in a stream always has an offset value of zero, indicating the first one in the stream. 2. The second datagram has an offset value of 512. 3. The third datagram has an offset value of 1024. The receiver stores datagrams in its memory buffer waiting for messages within the stream to arrive. However, it does not always receive the datagrams in order. For example, if the second datagram arrives first with offset 512, the receiver knows to expect several others because
70
TCP/IP PRIMER PLUS
The sending host has set More Fragments bit in the second datagram. This is not the Last Fragment. The receiver has not received a datagram with the same ID containing fragment offset zero, which indicates the beginning. Because it has received a datagram with the More Fragments bit set and has not received a datagram with a Last Fragment bit set, it knows to expect more datagrams. Once the receiver gets all the fragments within the stream, it can put them in the correct order and pass them up to the upper-layer application for processing. Figures 3.5, 3.6, and 3.7 depict another example of fragmentation and reassembly as seen through a Sniffer. Figure 3.5 details the first datagram within the stream; Figure 3.6 details the second datagram within the stream and Figure 3.7 details the last datagram within the stream. In Figure 3.5 notice that in frame 1 (highlighted in the detail pane), the IP ID value of this frame (frame 1) and all other frames (frames 25) shown in the summary pane bear the same value of 2052, shown as continuation of indent=2052. This means that frames 15 all belong to stream 2052. Note that the sending host has set the More Fragments bit within the first frame, indicating the this datagram has more fragments or datagrams within this stream. In other words, this is not the last datagram. Also note that the sending host set the fragment offset to zero, indicating the first fragment in series 2502.
FIGURE 3.5
The More fragments bit is set indicating more datagrams will follow. The fragment offset set to zero indicates this is the first datagram within the stream.
Figure 3.6 shows the second fragment in stream 2502. Note that the More Fragments bit is set, indicating that more datagrams follow this one. Note that the fragment offset is 1480, which
71
indicates this is not the first datagram (because it is not zero). Because the last fragment bit is not set, we know it is not the last but somewhere in the middle (in this case second). The destination host uses this information to put the fragments in the stream in the right order when it receives all the fragments within the stream.
FIGURE 3.6
The fragment offset is used by the receiving host to reassemble datagrams.
Figure 3.7 skips fragment 3 and shows the final fragment in the stream. Note that this fragment belongs to the stream because it has the identification value of 2502 like all the other fragments. We know this is the last fragment because Last Fragment is set. The fragment offset of 7400 is higher than the previous fragments so the destination host knows this is the last fragment and starts at the offset.
Time To Live
All devices processing a datagram decrement the 1-byte TTL value, which is measured in seconds. This value has two main purposes: To define the maximum time a datagram may live on the Internet prior to being discarded. To ensure that undeliverable datagrams also are discarded. Before routers existed on the Internet, to ultimately remove a lost datagram from the network it was necessary to recognize and limit the time it traversed the network. The TTL timer was used for this purpose. It remains today and is used for various purposes, such as tracing a route to a destination host or network, which we will discuss later in this chapter. Basically, whenever a device such as a gateway processes a datagram, it must decrement this value by at least one before forwarding it. Each TTL value indicates a value of one second, which is more
72
TCP/IP PRIMER PLUS
time than it should take for a router to process a datagram. This value can typically be equated to a hop count indicating the datagram has passed through x number of routers by determining how many TTL units this value has been decremented.
FIGURE 3.7
Note the Last fragment bit is set indicating to the receiver that this is the last datagram within the stream.
A network administrator can configure the starting TTL value but this value cannot exceed 255 (seconds). The general rule is that a device may not forward a datagram with a TTL value of 1 or less. If a datagram has lived on the wire for 255 seconds and has not reached its ultimate destination, it has lived too long on the network and should be removed. When this occurs, the device that the TTL expired on sends an ICMP message back to the source indicating that the datagram TTL time has exceeded. We will discuss ICMP messages later in this chapter.
Protocol
The 1-byte protocol field contains a value that specifies the next protocol expected within the datagram. This value will contain one of two values: 06 (TCP) 17 (UDP) IP uses these values to identify to which upper-layer protocol to hand the information when it receives it.
Header Checksum
Because IP is a connectionless protocol, it does not implement any type of error correction mechanism, such as sequencing and acknowledgments. IP simply sends datagrams out,
73
addresses them, and hopes they reach their destination. Therefore, IP uses a simple checksum, contained in this 2-byte field, to verify the integrity of the IP header and the data being carried to ensure that nothing has happened to the bits while in transit between source and destination hosts. Intervening devices must recalculate and verify this checksum value along the way because some of the fields within the IP header change while in transit (for example, time to live). If at any point in time a device deems this value invalid due to damage, it trashes the datagram without sending a message to the source. IP relies on upper-layer protocols to detect the loss of a datagram and recover from it (retransmit).
Source Address
The sending host places its logical Network layer (IP address) address within this 4-byte field for identification purposes.
Destination Address
This 4-bit field identifies the recipients logical network layer address. This logical 32-bit IP address identifies the destination network and host.
Options
Hosts or gateways can implement optional parameters; when used, this variable-length field defines them here. However, options do not have to exist within a datagram; if implemented, all hosts and gateways must recognize and support their implementation. This could include the use of a security option as specified within by the precedence value used in the ToS field.
Padding
IP uses this variable-length field only when an IP header does not end on a 32-bit boundary. Because the IP header is expressed in 32-bit words, padding is used to ensure that this happens.
ICMP
End hosts and gateways (routers) use the Internet Control Message Protocol (ICMP), defined by RFC 792, as a control, messaging, and diagnostic protocol. ICMP exists at the Network layer of the OSI and Internet layer of the DoD models. (See Figure 3.1 to view where ICMP falls within the DoD and OSI models.) Although ICMP resides at the same layer as IP, ICMP is considered an integral part of the IP protocol. As such, it utilizes the services of IP for its delivery of messages. Figure 3.8 shows an ICMP echo message encapsulated within an IP datagram. There are many types of ICMP messages; the ICMP echo request probably is the most common. You can use the echo request as a diagnostic tool to check connectivity between end hosts. We discuss all ICMP types in more detail later in the chapter. Note the ICMP protocol type in the IP equals one (ICMP).
74
TCP/IP PRIMER PLUS
Echo Request and Reply

The term echo request and reply describes messages you can use to test network connectivity. You can do this by using the Ping utility. The Ping program uses these ICMP echo request and reply messages. An echo request is like you shouting to a network, Hello, are you there? What bounces back, be it negative or positive (connectivity or no connectivity), is the echo reply. Just as with an echo, you always receive a reply.
FIGURE 3.8
The ICMP echo message is used to verify network layer communications between hosts.
Destination hosts and gateways on occasion need to inform a source host of delivery problems, test connectivity to that host, ask for transmission to slow down, and so on. ICMP has a total of 15 different messages identified by the value contained within its type field used to inform a source host. These messages allow a source host to learn and recover from some (not all) of the problems that can occur on an internetwork. Although these messages inform a host of problems, ICMP does not guarantee a solution to these problems. Like IP, ICMP is a connectionless protocol. Hosts or gateways can send unsolicited ICMP control or diagnostic messages. ICMP uses many types of messages for different purposes. You might have used the familiar Ping utility (ICMP message types 0 and 8). Ping allows a user to send a sonar-like ping from one host to another to verify connectivity. The Ping utility utilizes the services of ICMP messages to perform this task. When a user executes the Ping command specifying a remote hosts name or address, the host receives a series of ICMP messages, known as echo requests. The receiving host in turn responds to each of these messages using the ICMP Echo Reply message type 0. We discuss Ping and the other various message types and their purposes later in this chapter.
75
ICMP Header and Message Formats

IP identifies ICMP messages contained within an IP datagram with protocol type 1. Figure 3.9 shows the general format of an ICMP echo message. The first four bytes (1-byte type field, 1byte code field, and 2-byte checksum) have the same format for all message types. All other fields and information contained within the ICMP header vary depending on the message type being sent. We describe the various types, codes, and the checksum later in this chapter. Hosts and gateways use ICMP as a messaging, control, and diagnostic protocol to alert a host of problems or test connectivity. Note the protocol value contained within the IP header is 1, indicating this is an ICMP message. To determine the type of ICMP message, look in the ICMP header at the type field. Once you determine the type of ICMP message, you can use the code field to further identify the purpose of the message. The type field identifies the particular ICMP messages. Some ICMP messages use different values in the code field to further specify the error condition. The checksum field covers the entire ICMP message.
FIGURE 3.9
ICMP messages have a registered value of 1. The type field within the ICMP header identifies the type of ICMP message being sent.
Codes
Many of the type fields contain more specific information about the error condition identified by a code value. ICMP messages have two types of codes: Query Error Queries contain no additional information because they merely ask for information and will show a value of 0 in the code field. ICMP uses the following queries:
76
TCP/IP PRIMER PLUS
Type 0 = Echo Reply Type 8 = Echo Request Type 9 = Router Advertisement Type 10 = Router Solicitation Type 13 = Timestamp Request Type 14 = Timestamp Reply Type 15 = Information Request (obsolete) Type 16 = Information Reply (obsolete) Type 17 = Address Mask Request Type 18 = Address Mask Reply Error messages give specific information and will have varying values that further describe conditions. Error messages always include a copy of the offending IP header and up to 8 bytes of the data that caused the host or gateway to send the error message. The source host uses this information to identify and fix the problem reported via the ICMP error message. ICMP uses the following error messages: Type 3 = Destination Unreachable Type 4 = Source Quench Type 5 = Redirect Type 11 = Time Exceeded Type 12 = Parameter Problems Table 3.1 lists all of the ICMP codes along with the ICMP message types. We will discuss error codes and the various ICMP message types to which they pertain later.
Checksum
The checksum verifies the validity of the ICMP header. The sending host performs the initial checksum calculation and places the results in this field. The receiving host performs the same calculations to assure that it does not receive data damaged in transit. If the checksum values do not match, it trashes the datagram.
Identifier
The user on the source host can set this optional value to match sent echo requests with received replies.
Sequence Number
The user on the source host can set this optional value to match sent echo requests with received replies.
77
ICMP Message Types

The type field identifies the type of the message sent by the host or gateway. Many of the type fields contain more specific information about the error condition. Table 3.2 lists the ICMP message types.
TABLE 3.2 Type 0 3 4 5 8 9 10 11 12 13 14 15 16 17 18
ICMP Message Types

Description ICMP Message Types Echo Reply (Ping Reply, used with Type 8, Ping Request) Destination Unreachable Source Quench Redirect Echo Request (Ping Request, used with Type 0, Ping Reply) Router Advertisement (Used with Type 9) Router Solicitation (Used with Type 10) Time Exceeded Parameter Problem Timestamp Request (Used with Type 14) Timestamp Reply (Used with Type 13) Information Request (obsolete) (Used with Type 16) Information Reply (obsolete) (Used with Type 15) Address Mask Request (Used with Type 17) Address Mask Reply (Used with Type 18)
Because each of the ICMP message headers vary depending on which one is sent, we will discuss each type separately, identifying the corresponding code fields, if applicable.
Ping: Echo Request and ReplyTypes 8 and 0

We discuss the ICMP Echo Request Type 8 and Echo Reply Type 0 because ICMP uses these messages in tandem. Remote hosts use these two message types to test connectivity. As previously mentioned, the user executes the Ping utility, initiating the generation of ICMP echo requests with the expectation that the destination host sends a corresponding echo reply. Upon successful receipt of the replies to the echo requests, the messages do the following:
78
TCP/IP PRIMER PLUS
Indicate a successful test. Assume that a valid communication path between the hosts exists. Assume the end host works through the Network layer. Figure 3.10 shows an example of an echo request; Figure 3.11 shows an example of an echo reply. In Frame 1 host 36.53.0.202 sends an echo request to test the connectivity with host 36.21.0.1. Note the detail pane indicates a type 8 value stating this is an echo request. The ID value of 52743 and the sequence number of 57098 are optionally included to provide a reasonable match with the echo reply. In Frame 2 host 36.53.0.202 returns the echo reply to host 36.21.0.1. The type code 0 indicates this is a reply and the previous ID and sequence number values used in the echo request frame match.
FIGURE 3.10
This is an example of an echo request and reply generated as a result of the Ping Utility.
Destination UnreachableType 3
ICMP Type 3 message Destination Unreachable alerts a source host of delivery problems encountered while trying to reach the destination. Note that a destination host sends only code types 2 and 3; a router can send all codes. Destination Unreachable uses several code values to further describe the function of the ICMP message being sent. Each code type describes a different delivery problem encountered, as shown here:
79
FIGURE 3.11
This is an ICMP echo reply message sent in response to a previously received echo request.
0 = Network Unreachable This message indicates that the router cannot find the destination network (does not exist or has failed) or has no route to this network. In other words, the router cannot deliver or forward an IP datagram to the destination network. This could be the result of a network that is beyond the maximum distance limitation for the routing protocol in use and is therefore considered unreachable (too far). When a client attempts to connect to a host on a network that is unreachable, a gateway generates this message to alert the source host of the problem. You can think of this message as the gateway saying to the sending host, The street you are trying to locate is not found or is too far to reach. 1 = Host Unreachable The host unreachable message alerts the sending host that the destination host requested cannot be found. This could happen because this host has been turned off or does not exist. You can think of this message as the gateway saying to the sending host, I found the street you were looking for, but the house you are trying to find is not there. 2 = Protocol Unreachable Protocol unreachable indicates that the Transport layer protocol (UDP or TCP) is not available. The destination host or an intervening gateway might send this message. You can think of this message as saying, The transport layer protocol you are attempting to communicate with is not active on this host. 3 = Port Unreachable A port unreachable message indicates that the process or application the source host is attempting to establish a connection with is not active on the destination host. Typically this
80
TCP/IP PRIMER PLUS
type of message is sent when an application has not been started or has failed on this host. The destination host or an intervening gateway might send this message. You can think of this message as saying, The process or application you are attempting to communicate with is not active on this host, or, I found the street, I found the house, the lights were on, but no one was home. Figure 3.12 shows a request being sent from a BOOTP client looking for a BOOTP server. Figure 3.13 shows an example of an ICMP destination port unreachable message generated because the router or gateway could not find the BOOTP server, or the server was unavailable. We discuss BOOTP in Chapter 4, Address Resolution, and UDP in Chapter 9, User Datagram Protocol (UDP).
FIGURE 3.12
In frame one, highlighted in the summary pane and show in the detail pane, we see a BOOTP client, UDP port=68, sending a broadcast to all hosts using UDP port 67, which identifies a BOOTP Server process requesting an IP address.
In Figure 3.13 note that the gateway has added a copy of the offending IP header within the ICMP header that caused the error from frame one. By including a copy of the offending IP header, the source might be able to use this information to correct the problem that resulted in this ICMP message being sent. 4 = Fragmentation is needed, but dont-fragment bit set This message occurs when a router receives a datagram that requires fragmentation, but the router has the DF (dont-fragment) flag turned on. We discussed fragmentation earlier in the chapter. If you recall, the sending host generally has the responsibility of fragmentation. The receiver has the responsibility of reassembly. However, when a router cannot forward a datagram because it is too big, if allowed the router might fragment the datagram further before transmitting it to an attached segment. If the router has the DF bit set, this will not happen and the router will trash the datagram. It then
81
generates a message to alert the sender of this action by sending a Type 3, Code 4 message. The fragmentation bit also can determine the maximum packet size or MTU that hosts can transmit end to end along the communication path.
FIGURE 3.13
In frame two, highlighted in the summary pane and shown in the detail pane, we see an ICMP message being sent by a gateway (36.53.0.204) stating the previous request failed because the port request (68) is not active and therefore unreachable. As you can see in the detail pane, immediately following the IP header is the ICMP header.
Hosts can use the ICMP messages sent by routers to resize datagrams, dynamically adjusting to the needs of the network. This allows the host to determine the smallest MTU path to a destination. 5 = Source Route Failed The message occurs if a router encounters a next hop in the source route that does not reside on a directly connected network. 6 = Destination Network Unknown This message occurs when a router receives an IP datagram that it cannot deliver or forward to a particular network because it is unknown. 7 = Destination Host Unknown This message occurs when a router receives an IP datagram that it cannot deliver or forward to a particular host because it is unknown. 8 = Source Host Isolated (obsolete) 9 = Destination Network Administratively Prohibited This message occurs when a router receives an IP datagram that it cannot deliver or forward to a particular network because it is not allowed. Access to this network has been prohibited.
82
TCP/IP PRIMER PLUS
10 = Destination Host Administratively Prohibited This message occurs when a router receives an IP datagram that it cannot deliver or forward to a particular host because it is not allowed. Access to this host has been prohibited. 11 = Network Unreachable for ToS This message occurs when a router receives an IP datagram that it cannot deliver or forward to a particular network because the ToS requested is not available. 12 = Host Unreachable for ToS This message occurs when a router receives an IP datagram that it cannot deliver or forward to a particular host because the ToS requested is not available. 13 = Communication Administratively Prohibited by Filtering This message occurs when a router receives an IP datagram that it cannot deliver or forward to a particular host because it is not allowed. An administratively configured filter has prohibited access to this process or application. 14 = Host Precedence Violation This message occurs when a router receives an IP datagram that it cannot deliver or forward to a particular host because the precedence level requested does not match, and is not accepted or is invalid. This could be a source host attempting to access a high security host without the necessary security clearance values. 15 = Precedence Cutoff in Effect This message rarely occurs. However, you will receive this message when a packet is dropped by the cutoff function.
Precedence Handling For All Routers

Routers must accept and route incoming traffic of all precedence levels normally, unless you have configured it to do otherwise. If you want to learn more about precedence and Destination Unreachable messages 14 and 15, please refer to RFC 1812, 5.3.3.3, Precedence Handling for All Routers.
Source QuenchType 4
A receiving host generates this message when it cannot process datagrams at the speed requested due to a lack of memory or internal resources. This message serves as a simple flow control mechanism that a receiving host can utilize to alert a sender to slow down its transmission of data. When the source host receives this message, it must pass this information on to the upper-layer process, such as TCP, which then must control the flow of the applications datastream. A router generates this message when, in the process of forwarding datagrams, it has run low on buffers and cannot queue the datagram for delivery.
83
RedirectType 5
A router sends a redirect error to the sender of an IP datagram when the sender should have sent the datagram to a different router or directly to an end host (if the end host is local). The message assists the sending host to direct a misdirected datagram to a gateway or host. This alert does not guarantee proper delivery; the sending host has to correct the problem if possible. Only gateways generate redirect messages to inform source hosts of misguided datagrams. Note that a gateway receiving a misdirected frame does not trash the offending datagram if it can forward it. The gateway forwards the frame, sends an alert message to the source, and hopes the source host will properly direct future frames to the designated host or gateway indicated in the message. ICMP redirect messages alert source hosts when a datagram has been misdirected and should be resent. Four redirect error codes can occur: 1. 0 = Redirect for Network 2. 1 = Redirect for Host 3. 2 = Redirect for Type-of-Service and Network 4. 3 = Redirect for Type-of-Service and Host Figure 3.14 shows an example of a ICMP redirect message. In this example, a gateway (36.53.0.1) alerts host (36.53.0.174) that it should be sending future datagrams to the following gateway internet address (36.53.2.2). This alert message also includes a copy of the offending IP header for the source hosts inspection.
FIGURE 3.14
ICMP redirect messages are sent by gateways to hosts alerting them of messages that have been misdirected.
84
TCP/IP PRIMER PLUS
Router Advertisement and SolicitationTypes 9 and 10

Rather than initializing a routing table with static routes specified in configuration files, you can use the router ICMP advertisement and solicitation messages. After bootstrapping, a host can transmit a broadcast or multicast a solicitation message to which a router or routers responds with a router advertisement. This allows communicating hosts to learn of available routes dynamically and update their routing tables. We will discuss routing in more detail in Chapters 5 and 6.
Time ExceededType 11
The time exceeded message occurs when a router receives a datagram with a TTL (Time To Live) of 0 or 1. IP uses the TTL field to prevent infinite routing loops. A router cannot forward a datagram that has a TTL of 0 or 1. Instead, it trashes the datagram and sends a time exceeded message. Two different time exceeded error codes can occur: 1. 0 = Time-To-Live Equals 0 During Transit 2. 1 = Time-To-Live Equals 0 During Reassembly Note that a router cannot forward a datagram with a TTL of 0 or 1 both during transit or reassembly. As previously mentioned in the IP section of this chapter, the TTL timer is measured in seconds and originally was used before the existence of routers to guarantee that a datagram did not live on the Internet forever. Each gateway processing a datagram reduces this value by at least one if it takes longer to process and forward the datagram. When this value expires, the gateway trashes the datagram and sends a message back to the sender notifying the host of the situation. The traceroute utility also uses the TTL value to discover the path or route to a destination host or network. Upon execution of the traceroute command, the initial ICMP message is sent out with a TTL value of 1 set in the IP header. You can use the traceroute program to determine, or rather trace, the path to a destination. Traceroute accomplishes this by sending a sequence of datagrams with the TTL set to 1, 2, and so on. It then uses the ICMP Time Exceeded messages like a trail of breadcrumbs to trace the routers along the path. We will provide you with examples later in this section. As you might recall from earlier in this chapter, when a router receives a datagram with a TTL of zero, it trashes the datagram and returns an ICMP time exceeded message to the source. This message allows the host to learn of the first router in the path to the destination. Figure 3.15 shows an ICMP message generated as a result of a TTL expiration. As shown in the figure, ICMP message type 11 alerts a source host of a TTL expiration. Code 0 identifies the reason for the expiration as time to live being exceeded while the datagram was in transit. This message also includes a copy of the original datagram header that caused the error to assist the source host in correcting the problem. Within the offending header
85
contained within the ICMP message, you can see that the TTL value = 0 seconds/hops, which is why the original datagram was trashed.
FIGURE 3.15
The ICMP time exceeded message is sent when the TTL timer expires.
Now the source host sends a new ICMP trace with a TTL value of 2, which allows this datagram to be forwarded by the first router (which decrements the value by one) and reaches the next router in the path with a TTL of one. This router must trash the frame and send back an ICMP time exceeded. This process continues until the path to the destination network or host is fully discovered or deemed unreachable. As you can see, traceroute is another useful troubleshooting tool, typically used in conjunction with other utilities such as the Ping utility to test connectivity between two hosts.
Tip
Both the Ping and traceroute utilities can help you when troubleshooting.
Parameter ProblemType 12
The parameter problem message indicates that a host or gateway received and could not interpret an invalid or misunderstood parameter. A host or gateway also can send this message when no other ICMP message covering the problem can be used to alert the sending host. In this respect, it is a catchall message. In most cases this message indicates some type of implementation error occurred, perhaps because of vendor incompatibility issues. A host or gateway will not send this message unless it trashes the datagram containing the parameter problem.
86
TCP/IP PRIMER PLUS
Two parameter problem error messages can occur: 1. 0 = IP Header Bad (catchall error0) A host or gateway sends this error to indicate a general implementation error of an unspecific nature. 2. 1 = Required Option Missing The host or gateway expected a specific option, but the sender did not send it.
Timestamp Request and ReplyTypes 13 and 14

Timestamp request and reply messages work in tandem. You have the option of using timestamps. When used, a timestamp request permits a system to query another for the current time. It expects a recommended value returned to be the number of milliseconds since midnight, Coordinated Universal Time. This message provides millisecond resolution, considered a beneficial feature when compared to other means of obtaining time from another host who provides resolution in seconds. The two systems compare the three timestamps and use RTT to adjust the senders or receivers time if necessary. Note that most systems set the transmit and receive time as the same value. The process for time resolution goes as follows: 1. The requestor stamps the originate time and sends the query. 2. The replying system stamps the receive time when it receives the query. 3. The replying system stamps the transmit time when it sends the reply to the query.
Information Request and ReplyTypes 15 and 16

Although ICMP messages list information request and reply as a potential ICMP message type, they actually do not occur; thus they are obsolete. A host can request information such as to what network it was attached.
Address Mask Request and ReplyTypes 17 and 18

Address mask request and reply messages work in tandem. Although we rarely use this message today, its original design supported the function of dynamically obtaining a subnet mask. Hosts can use the ICMP address mask request to acquire subnet masks during bootstrap from a remote host. However, problems can occur when using ICMP to receive a mask if a host gives an incorrect mask from an external source. If the external source does not give a response, the source host must assume a classful mask (that the network is not subnetted).
Summary
IP is the workhorse of the Network layer within the TCP/IP suite. All protocols and applications utilize IP for logical Network layer addressing and transmission of datagrams between
87
internet hosts. IP provides an unreliable, connectionless datagram delivery service and uses ICMP to send messages when it encounters an error. End host and routers use ICMP as a control, messaging, and diagnostic tool. ICMP utilizes IP to deliver its messages and is considered an integral part of IP. ICMP messages notify a host of problems. Although ICMP does not offer a solution to these problems, it can provide enough information for a source host to solve some of the problems that might occur in the internetwork. The most popular ICMP message is the echo request and reply. Utilizing the Ping utility, these messages allow you to test connectivity between end hosts.
Review Questions
1. Which Network layer protocol is responsible for fragmentation and reassembly of datagrams? 2. A user would like to test connectivity between two remote hosts, so the user executes Ping. Which two ICMP message types are used to accomplish this test? 3. What does IP do when it receives data from UDP or TCP? 4. How many minimum bytes are there in an IP header and what fields are contained within that header? 5. What are the ToS bits within the IP header used for? 6. What two field values does the destination host use to ensure that it reassembles datagrams in the correct order? 7. What type of ICMP message is Destination Unreachable, and what does it mean if you receive a Destination Unreachable ICMP message? 8. What does a 0 (zero) error code mean when you have a type 3, Destination Unreachable ICMP message? 9. What does a 4 error code mean when you have a type 3, Destination Unreachable ICMP message? 10. What type of ICMP message is Time Exceeded and what does it mean if you receive a Time Exceeded ICMP message?
CHAPTER 4
ADDRESS RESOLUTION

Address Resolution Protocol Reverse Address Resolution Protocol BOOTP Dynamic Host Configuration Protocol
ecause of the complexity of the various layers and the various addresses that reside at those layers, there must be a method to resolve differences between computer addressing schemes. Address resolution assumes that role and enables end devices to dynamically discover a local hardware address for delivery of data to a remote host, or retrieve logical IP addresses and configuration parameters necessary to participate on the network. Without some type of resolution method, remote hosts could not communicate. In the IP world address resolution converts a protocol address into a corresponding physical address or vice versa; for example, converting an IP address into an Ethernet address. There are four methods of address resolution: ARP (Address Resolution Protocol) RARP (Reverse Address Resolution Protocol) BOOTP (Bootstrap Protocol) DHCP (Dynamic Host Configuration Protocol) Figure 4.1 shows how these protocols map to the DoD and OSI models. Of the four protocols that perform address resolution, ARP is the only one that resolves Network layer addresses to hardware addresses. The RARP, BOOTP, and DHCP protocols allow an end device to dynamically resolve its hardware address to a logical Network layer address. Figure 4.2 shows an example of ARP resolution. Figure 4.3 shows an example of RARP, BOOTP, and DHCP resolution. We will discuss these protocols in more detail later in this chapter.
90
TCP/IP PRIMER PLUS
FIGURE 4.1
DOD
OSI
Application Presentation
Note that ARP and RARP utilize IP at the Network layer, and DHCP and BOOTP run on top of UDP at the Transport layer.
Host-to-Host
Session Transport
Internet
BootP, DHCP, ARP, RARP
Network Access
FIGURE 4.2
ARP
Logical Address 100.1.5.2
ARP resolves logical Network layer addresses to a local hardware address.
Hardware Address 00c0.00df.1135
FIGURE 4.3
RARP, BootP and DHCP

Logical Address 100.1.5.2
RARP, BOOTP, and DHCP protocols resolve an end devices hardware address to a logical Network layer address. These protocols perform the opposite function of ARP.
Hardware Address 00c0.00df.1135
Chapter 4 ADDRESS RESOLUTION
91
ARP
When you attempt to initiate a session with a remote hosts application, you can use either the name of the remote host or the logical Network layer address. For example, if you utilize the remote hosts name and request a Telnet session by typing Telnet TelnetServ (name of the remote server), this name would need to be resolved to a logical Network layer IP address and then resolved to a Data Link layer hardware address. If you attempt the session using the logical Network layer address, you do not need to perform the name resolution portion. However, the remote host still needs to resolve its logical Network layer IP address to a hardware address for proper delivery. ARP (Address Resolution Protocol), defined in RFC 826, performs this last address resolution dynamically. The initial design of the ARP protocol supported the resolution of logical Network layer addresses into 48-bit (6-byte) Ethernet hardware addresses. Since then, it has evolved to support resolution for other types of networks. RFC826 documents these changes. Upper-layer applications and processes need the ARP protocol to dynamically resolve Network layer addresses for proper data delivery. Without this dynamic protocol you would have to resolve them manually by creating a static table on each host mapping the logical IP addresses of all internet hosts to their local hardware address or the address of a local gateway. This would prove impractical because there are many different types of logical Network layer addresses, and they vary in size. For example, they could be IP addresses (32 bits) or Xerox (8 bits). Rather than manually identifying and mapping these addresses to the lower layer, 48-bit address, ARP performs this process automatically. Although the ARP protocol can resolve various types of logical Network addresses to hardware addresses, we will focus only on the resolution of IP addresses in this chapter.
ARP Operation
Before any communication can occur between remote hosts, the sender must obtain a local address for delivery. If the source and destination hosts exist on the same segment, this local address will be the hardware address of the ultimate destination. If the source and destination hosts do not reside on the same local segment (hosts separated by a router or multiple routers), the sender uses the routers (gateways) local address for delivery, forwarding the datagram to the remote host. To obtain the local hardware address, the sending host first checks its local ARP cache table for a previously learned address. Each host maintains a local ARP table in memory containing static (manually entered) or dynamic learned address information. A host can learn the address information in the following ways: Through an administrator mapping a logical Network layer to a hardware address (statically). Dynamically through ARP. However the host learns, it stores the address information in its local ARP table. If an address pair exists in the table, the source host can simply use this information without going through
92
TCP/IP PRIMER PLUS
the process of using ARP to resolve the address. If the address pair does not exist, which might be the case if the host has just initialized and has an empty ARP cache, the sending host uses ARP to resolve the destination hosts Network layer address to a local hardware address. Once the sending host resolves the Network layer address and determines a local address, it places this information in the local hosts ARP cache for later use. Storing this information in cache eliminates the need for this host to perform this resolution in the near future when connecting to the same host. ARP is broadcast based. This means that when a sending host wants to resolve a remote hosts Network layer address, it sends a broadcast out to all hosts on the local segment. Routers do not forward broadcasts; therefore, broadcasts remain localized to the sending hosts segment. Note that routers will forward a broadcast if a helper address has been configured (for BOOTP and DHCP) or if you have IP directed-broadcast enabled; however, please remember that routers do not inherently forward broadcasts. As we discussed in the previous chapter, the sending host determines whether the destination resides on the sending hosts local segment by comparing the destination hosts IP address to the sending hosts local subnet mask. If after performing this task the sending host finds the destination host resides on the same subnet, the sending host knows that it can shout (send a local ARP broadcast to resolve the destination hosts hardware address). However, if the sending host finds that the destination host does not reside on the same subnet, it must route, which means the sending host sends a local broadcast to resolve the local gateways IP address to a hardware address for forwarding. Once the sending host determines whether it can shout or route, it sends a local query to resolve the destination host or local gateways IP address to a hardware address. The sending host asks in its ARP broadcast, Does anyone recognize the Network layer address x.x.x.x? (The xs in this case would represent the 32-bit IP address of the destination host or local gateway). The sending host expects one of two things to happen: The destination host responds to this query The local gateway that forwards this datagram responds Figure 4.4 shows a sending host sending an ARP broadcast to resolve a local hosts hardware address. In this figure, Host A wants to communicate with Host B, which is on the local segment. Host A simply sends an ARP broadcast on the local segment querying whether anyone recognizes the address 100.0.0.2. Host B responds to this request with its local address. If a sending host finds that a destination host resides on the same subnet, it sends a local ARP broadcast to resolve the destination hosts hardware address. If a sending host finds that a destination host does not reside on the same subnet, it sends a local ARP broadcast to resolve the local gateways hardware address, which forwards the datagram to the remote host. Figure 4.5 shows a host sending an ARP broadcast resolving a local gateways IP address to a local hardware address for delivery to a remote host. In this figure, Host A wants to communicate with Host B, which is not on the same network. Host A sends an ARP broadcast on the local segment to resolve the local gateway address to the hardware address. End hosts must be configured with the IP address of a local gateway to communicate beyond their local segment.
93
FIGURE 4.4
In this case, Host A simply shouts out an ARP broadcast on the local segment.
ARP For Local Host

Does anyone recognize address 100.0.0.2?
A
ARP Broadcast from Station A
B
100.0.0.2
I recognize that address! Here's my hardware address 1122.3344.5566
FIGURE 4.5
ARP For Local Gateway

In this case, Host A needs to route.
110.0.0.10
ARP Broadcast 88.0.0.5

I recognize that address! Here's my hardware address 0000.1111.2222
Basically the destination host or the local gateway responds, I recognize that address and here is my hardware address. The sending host then has enough information to forward the datagram to the end host or the gateway en route to this host. With this information the sending host now can address a datagram properly, reflecting the logical Network layer address of the ultimate destination and the hardware address of the local host or gateway responsible for delivering the datagram. If the sending host sends the datagram to a gateway for delivery, the gateway determines how to forward the datagram to the remote host. The gateway that has this responsibility goes through the following process to determine how to forward the datagram:
94
TCP/IP PRIMER PLUS
1. If the destination host resides on a segment local to this gateway, the gateway checks its local ARP cache for a previously cached entry. 2. If no entry exists for the destination host, the router sends an ARP request querying all devices on that segment to learn the destination hosts hardware address for delivery. 3. If the destination host does not reside on a segment local to this gateway, the gateway uses ARP to learn the hardware address of another local gateway it can use to forward the datagram to the destination host. 4. This process continues along the delivery path until a gateway connected to the same subnet as the destination host receives the frame and uses a previously cached hardware address or performs a local ARP, resolving the Network layer address to the local address of the ultimate host.
ARP Cache Mechanisms

Depending on the implementation, hosts can use one or more control mechanisms to remove old or invalid entries from the ARP table. These mechanisms ensure valid entries exist in the table. For example, if a local host changes its Ethernet address (someone replaces the network interface card), it needs a new mapping. The control mechanisms are discussed in the following sections.
Timeout
Each host has a configurable ARP cache timer that controls how long it retains a dynamically learned entry. Configuration of this timer varies based on the operating system used. When a host adds an entry to the ARP table, it sets the timer value. When the timer expires, it considers the entry obsolete and flushes the entry from cache. If this host attempts to contact the other host using the address it flushed, it sends a new ARP query, causing a new entry to be added to the table. Each time a host uses an entry within its cache, the timer resets for that entry. This means if this host communicates on a regular basis with a remote host, the entry will remain in the ARP cache.
Unicast Poll
A directed datagram using the mapping information previously learned and cached polls a host periodically. If the remote host does not send an ARP reply in response to the polls, the sending host considers the entry for this remote host invalid and removes it from the table. If the remote host responds, the sending host considers the entry valid and keeps it in the table.
Link Layer or Higher Layer Advice

If the Link layer or a high-layer protocol detects a delivery problem, that protocol sends notification of this problem to the active ARP process within the host. Upon notification, ARP considers the entry for the remote host invalid and removes it from the table.
95
Proxy ARP
Proxy ARP enables another device, such as a gateway, to respond to ARP requests on behalf of a remote host for address resolution purposes. The router acts as the actual destination host (a proxy agent). In reality, the intended destination host lies on the other side of the proxy agent on another network. This fools the sender, allowing the gateway to relay datagrams from it to other hosts transparently. Sometimes it is necessary to enable Proxy ARP; for example, if a network administrator misconfigured network hosts or wanted to connect multiple segments through a router, yet simulate a single subnet. An administrator can enable Proxy ARP on networks through configuration options in hosts or gateways where desired. Proxy ARP allows transparent communication to occur between remote hosts even with misconfigured hosts. In this respect Proxy ARP acts as a bandage that masks an underlying problem within the networks addressing scheme. Enabling Proxy ARP does not provide an ultimate solution to this problem. Following a hierarchical addressing scheme and configuring hosts and gateways properly serves as the only true solution.
Proxy ARP Operation

The best way to understand how Proxy ARP works is to look at an example. In Figure 4.6 the sending host and the destination host reside on different subnets (Host A resides on 172.15.1.0 and Host B resides on 172.15.2.0). Note that the gateway between them is configured for Proxy ARP. The gateway has the capability to respond to local ARP requests on behalf of remote hosts. When a gateway enabled for Proxy ARP does so, it responds with its own hardware address. Host A, misconfigured with an incorrect subnet mask (255.255.0.0), believes that Host B resides on the same network. Because of this, Host A believes that it can shout (send a local ARP broadcast to resolve Host Bs IP address to hardware address) when in fact, Host A actually should route (send a local ARP broadcast to resolve the gateways IP address) to hardware address for delivery.
FIGURE 4.6
Proxy ARP
Proxy ARP allows a router to answer ARP requests for a host on another network.
172.15.2.2 255.255.255.0
A
172.15.1.2 255.255.0.0
I recognize address 172.15.2.2! Here's my hardware address 0000.ac11.dddd
Proxy ARP
96
TCP/IP PRIMER PLUS
Take a look at Figure 4.6 and walk through the steps of what occurs during a Proxy ARP request: 1. Host A, 172.15.1.2, on network 172.15.1.0 and Host B, 172.15.2.2, on remote network 172.15.2.0 want to communicate. A router configured for Proxy ARP separates Host A and the remote network, Host B. 2. An administrator has configured Host A with a standard Class B subnet mask of 255.255.0.0. This is a problem because the network (172.15.0.0) actually is further subnetted and instead should have a standard Class C mask of 255.255.255.0. Host A attempts to determine whether to send a local ARP request to station B (shout) or the gateway (route) by taking the destination hosts IP address and comparing it to Host As mask. 3. Because Host As mask states that the values within the first and second byte are network, it appears to Host A that they both reside on the same network 172.15.0.0, which is not the case. Because of this incorrect information Host A decides to send a local ARP broadcast (shout) out on this segment to resolve Host Bs Network layer address to a hardware address. 4. Because Host B does not reside on this local segment it does not hear this broadcast; thus it does not respond. Normally this local ARP would fail. However, with the local gateway configured as an ARP Proxy Agent, this is not the case. 5. The gateway (router) configured for Proxy ARP picks up this ARP request and responds on behalf of Host B, replying with its own hardware address. This allows Host A to transparently communicate with Host B even though Host A is misconfigured.
ARP Header
An ARP header contains 28 bytes. Figure 4.7 takes a look at the format of an ARP header. Figure 4.8 takes a look at the fields and functions within an ARP header as seen through the Detail pane of a Sniffer protocol analyzer. Figure 4.9 shows an ARP request and reply used to resolve an IP address to an Ethernet hardware address. The descriptions for each field follow the figures.
FIGURE 4.7
HARDWARE TYPE HLEN PLEN SENDER HA (octets 0-3) SENDER HA (octets 4-5) SENDER IP (octets 2-3) SENDER IP (octets 0-1) TARGET HA (octets 0-1) PROTOCOL TYPE OPERATION
Note that ARP and RARP use the same header format.
TARGET HA (octets 2-5) TARGET IP (octets 0-3)
97
Notice in Figure 4.8 that ARP protocol type is indicated in the Data Link Control header as Ethertype 0806. The destination hardware address has all Fs in the field, indicating that this request is being broadcast to all devices on this local segment. The Opcode value of 1 indicates that this is an ARP request as opposed to an ARP reply (OpCode 2). The sending host identified as Sun061787 (hardware address) and 129.84.25.26 (IP Address) queries to resolve a 4byte IP protocol (Ethertype hex 0x0800) target address 129.84.25.1 to a 6-byte Ethernet hardware address. Note that the target hardware address has all zeros, indicating it is unknown.
ARP Protocol type Destination hardware address
FIGURE 4.8
In this example, an ARP broadcast is being sent to the local segment.
Opcode Hardware address IP address Target hardware address
Target protocol address
The sending host Sun061787 sends a broadcast to all hosts on the local segment in Frame 1 asking whether they recognize the PA (Protocol Address) 129.84.25.1 PRO (Protocol Type being resolved) as IP. In frame two, Host 129.84.25.1 sends the ARP response stating its HA (Hardware Address) is ATT030001.
Hardware Type
This 2-byte field identifies the hardware type resolved as Ethernet, Token-Ring, or some other network type. ARP uses this field in conjunction with the protocol type field during ARP requests and replies to indicate which protocol is being resolved and to what hardware address.
98
TCP/IP PRIMER PLUS
Frame 1 Frame 2
FIGURE 4.9
Note the response (frame two) to the broadcast in frame one.
Protocol Type
The 2-byte protocol type field identifies the Network layer protocol type. This value makes ARP capable of resolving various Network layer protocol addresses. For example, IP has the well-known 2-byte registered protocol type of 0x0800 (hexadecimal) and IPX has the registered protocol type 0x8137.
Length of Hardware Address

This 1-byte field specifies the length in bytes of the hardware address ARP expects as a result of address resolution. This value varies depending on the hardware type, indicated in the hardware type field. For example, if the hardware type field indicates Ethernet (shown as a value of 1), which uses a 48-bit or 6-byte hardware address, the field will have a value of 6.
Length of Protocol Address

The length of the protocol address is the protocol size. The 1-byte protocol length field specifies the length in bytes of the Network layer protocol address being resolved. Because ARP can resolve logical Network layer addresses for multiple protocols, it needs the protocol value defined. For example, if the protocol type field specifies IP (0x0800), the field expects a 4-byte value, indicating a 32-bit address.
99
Opcode
The two-byte Opcode (operation code) field specifies the type of operation occurring: 1. ARP request (value of 1) 2. ARP reply (value of 2) 3. RARP request (value of 3) 4. RARP reply (value of 4) ARP needs this field because the frame format used by both ARP and RARP include the same fields. Therefore they look the same. The Opcode value identifies the purpose of the frame. The frame clearly states whether an ARP or RARP request or reply has occurred. You also can distinguish an ARP frame from an RARP frame by checking the Ethertype value identified within the DLC header. ARP has a protocol type of 0806, whereas RARP has a protocol type of 8035. We discuss the RARP protocol later in this chapter.
Senders Hardware Address

The sending host places its hardware address within this field for identification purposes. The senders hardware address field is 6 bytes.
Senders Protocol Address

The sending host places its logical Network layer (IP address) address within this field for identification purposes. The senders protocol address field is 4 bytes.
Target Hardware Address

This 6-byte field identifies the destination hosts hardware address if known or all zeros if unknown. When a host tries to resolve a target hosts Network layer protocol address to a hardware address, this field will have all zeros as its value, indicating an unknown value.
Target Protocol Address

This 4-byte field identifies the Network layer protocol (IP) address of the destination host. When a host sends an ARP request, this field shows the logical address of the host being resolved.
RARP
RFC 903 defines the RARP protocol, which was designed to perform dynamic resolution of a hosts hardware address into a logical Network layer protocol address. RARP has the opposite function of the previously discussed ARP protocol. In fact ARP and RARP use the same header format and fields. Because they both use the same fields, we will not cover them again. Please
100
TCP/IP PRIMER PLUS
refer to the ARP header if you want more information. Another way to tell ARP from RARP is the protocol type; RARP is identified within the DLC header as Ethertype 8035, whereas ARP is type 0806. The RARP protocol was initially developed to enable diskless clients to dynamically retrieve a logical address from a remote host. Because diskless clients have no permanent area to store this information, they require a remote RARP server to store the hardware address and its corresponding Network layer address mapping in a static table. A network administrator must create this static mapping table on the RARP server for every client on a subnetwork and update it each time a hosts hardware address or Network layer address changes. Like the ARP protocol, the RARP protocol is broadcast based. This means internet gateways (routers) do not forward these datagrams. Because of this limitation, at least one RARP server needs to be located on each local subnet to service RARP client requests. Multiple RARP servers on a local subnet provide redundancy, eliminating a single point of failure. The requirement to have at least one RARP server per segment means there must be many RARP servers throughout a network to service the needs of diskless hosts or any host requiring dynamic logical address assignment. In addition, the administrator must update and maintain the static table regularly, which adds a lot of management overhead to a network.
RARP Operation
Before a host can communicate on any network, RARP requires certain configuration information. Diskless hosts or any host lacking this information must obtain it from somewhere. When a host initializes, if a host has not been previously configured with this information or has no place to store it, it can request the assignment of a logical Network layer protocol address from a remote host running the RARP process. The code RARP needs to initialize and complete the bootstrap operation for a client is small enough to fit in PROM (Programmable Read Only Memory) on the local host. To obtain a logical protocol address: 1. The sending host transmits a local RARP broadcast. 2. The host states its known hardware address and requests assignment of a logical protocol address from any RARP server receiving this request. 3. RARP servers on the local segment receive this request and check their RARP database for an entry mapping the sending hosts hardware address to a logical protocol address. 4. If this pair exists in the table, the RARP server sends a directed datagram to the source host providing the requested information. 5. If the address pair does not exist, which might be the case if no hardware address mapping exists in the RARP servers table, the server does not respond. 6. If the client does not receive a response from a RARP server it abandons the effort to obtain this information and does not initialize itself successfully as a participant on the network.
101
7. Once this process resolves a hardware address and determines a protocol address, it places this information in the local hosts memory. Its memory is maintained until the next boot.
ARP Versus RARP Operation

As you might recall, when we discussed the operation of the ARP protocol, we stated that you could think of a host sending an ARP query as Does anyone recognize the network layer address x.x.x.x? (The xs in this case would represent the 32-bit IP address of the destination host). Look at Figures 4.8 and 4.9 for examples of an ARP query. However, when a RARP sends a query, you can think of it as I know my hardware address; here it is. Can you tell me what my network layer address (x.x.x.x) is? Figures 4.10 and 4.11 show examples of a RARP request and RARP reply exchange.
Sending host Ethertype Frame 1
FIGURE 4.10.
In frame one, highlighted within the Summary pane and shown in the detail pane below, you can see the various fields of a RARP header. Note that the RARP protocol is Ethertype 8035.
Opcode type Hardware address Target protocol address
In Figure 4.10 Sun0115E8 sends the RARP request as a broadcast. Note that Opcode is type 3, indicating a request, not a reply. Also note the sending host knows and identifies its hardware address, but does not know its logical Network layer address; therefore, it uses all zeros in that field (0.0.0.0). The sending host does not know the hardware or IP address of the RARP server, nor does it need to because it sends this frame out as a Data Link layer broadcast and any RARP server on the segment will pick it up.
102
TCP/IP PRIMER PLUS
Keep in mind the purpose of this frame is to resolve its hardware address to a logical protocol address. Therefore, the target hardware address indicated within the RARP header for resolution is its own hardware address, and the target protocol address stated within the RARP header also is all zeros. Notice in Figure 4.11 that in the response frame the RARP reply has an Opcode value of 4. Note also that this frame is not a broadcast, but a directed datagram sent by the RARP server Sun014B7F (192.29.43.51) to host Sun0115E8 assigning it an IP address of 192.29.43.64.
FIGURE 4.11
RARP does the opposite of ARP; it resolves a hardware address to an IP address.
Disadvantages of RARP
Other, more robust protocols such as BOOTP and DHCP have replaced RARP; we will discuss this later in this chapter. RARP has two major disadvantages: Routers cannot forward requests and replies. An administrator must create and maintain a static mapping table. Because routers cannot forward requests and replies, RARP servers must exist throughout the internetwork (at least one per segment). This drastically affects the cost and implementation of RARP. Because RARP requires a static mapping table, an administrator must manually build and maintain the mapping table on a regular basis. This proves impractical when thousands of hosts exist or if changes frequently occur in your network. Each time a host moves, an administrator must update this information on the RARP servers. If a host has moved to a segment
103
and the local RARP server has not received this clients mapping information, or the administrator has input the mapping information incorrectly, the client will fail to connect to the network.
RARP Header
The RARP header looks nearly identical to an ARP header. The only difference appears in the frame type field in the RARP packet format (attached to the RARP header), indicating 0x8035 for an ARP request or reply. In addition, the Opcode field has a value of 3 for a RARP request and 4 for a RARP reply. Like an ARP header, the RARP header contains 28 bytes. We will take a look at the fields and functions within an RARP header. Refer to Figure 4.7 for an example of a RARP/ARP header.
Hardware
This two-byte field identifies the hardware type being resolved as Ethernet, Token-Ring, or some other network type. RARP uses this field in conjunction with the protocol type field during RARP request, asking the protocol address to correspond with the hardware address. If the RARP process resolves an Ethernet hardware address, this field will have a value of one.
Protocol Type
This two-byte field identifies the Network layer protocol type. This value makes RARP capable of resolving a hardware address to various logical protocol addresses. For example, if the RARP process resolves the protocol type IP, this field will have the value of the well-known registered protocol type for IP 0x0800.
Length of Hardware Address

This 1-byte field specifies the length in bytes of the hardware address that RARP resolves. This value varies depending on the hardware type indicated in the hardware type field. For example, if the hardware type is Ethernet (shown as a value of 1), which uses 48-bit or 6-byte hardware addresses, the hardware address field will have a value of 6.
Length of Protocol Address

This 1-byte field specifies the length in bytes of the Network layer protocol address that RARP expects as a result of address resolution. Because RARP can resolve a hardware address to various logical Network layer addresses for multiple protocols, it needs this value defined. For example, if the protocol type field specifies IP (0x0800), it will expect the length of protocol address field to be 4 bytes or 32 bits.
Opcode
This two-byte field specifies the type of operation occurring:
104
TCP/IP PRIMER PLUS
1. ARP request (value of 1) 2. ARP reply (value of 2) 3. RARP request (value of 3) 4. RARP reply (value of 4) RARP needs this field to differentiate between a RARP request and RARP reply.
Senders Hardware Address

The sending host places its hardware address within this field for identification purposes. This field has 6 bytes.
Senders Protocol Address

The sending host places its logical Network layer address within this field for identification purposes. This field has 4 bytes. If this field has a protocol address value of all zeros, the RARP client has performed its initial request broadcast to all RARP servers. All zeros indicate the sending host does not know this address.
Target Hardware Address

This 6-byte field identifies the destination hosts hardware address. In a RARP request this value has the senders hardware address. In a RARP reply this value has the hardware address of the RARP client.
Target Protocol Address

This 4-byte field identifies the network layer protocol address of the destination host (target). A RARP request sends this value as all zeros (unknown) because by sending this request, RARP attempts to learn this address. In a RARP reply this value has the logical address assigned to the RARP client by the RARP server.
BOOTP
You already know why we need address resolution; you also are familiar with the operation of the ARP and RARP protocols, and their fields and functions. As you might recall from this chapter, both are broadcast based and are used to resolve addresses for hosts. ARP resolves a hosts logical to hardware address; RARP resolves the hardware to logical address. Remember that as broadcasts these datagrams do not pass through routers. The evolution of the BOOTP (Boot Parameter) protocol was intended as the next protocol to replace RARP. Defined within RFC 951, BOOTP initially was intended (like RARP) to be used by diskless clients requesting IP address information from a remote server. In addition to retrieving address information, a diskless host also could request a remote boot file from a TFTP server or some other remote boot server for initialization purposes.
105
Like RARP, upon initialization BOOTP clients address all hosts running the BOOTP server process (this can be a host or a gateway), requesting IP address configuration information. All BOOTP servers maintain a local static configuration table mapping hardware addresses to valid IP addresses used to fulfill client requests. The network administrator must manually update and maintain this table. Unlike ARP and RARP, which sit at the Network layer and actually use the services of IP for the delivery of their requests and responses, BOOTP utilizes the services of UDP and IP for delivery. The UDP port value 68 identifies a client, and the value 67 identifies a server port. TCP and UDP ports are discussed in detail in Chapter 7, Transport/Host-to-Host Layer, and Chapter 8, Transmission Control Protocol (TCP), respectively. Also, unlike ARP/RARP, routers can forward BOOTP requests and responses. This allows BOOTP servers to be strategically placed throughout the internetwork without requiring a BOOTP server on each and every network segment. You have three options when configuring a BOOTP server: 1. Configure routers (gateways) on the internetwork to forward BOOTP client, and server requests and responses by enabling UDP ports 67 and 68. 2. Configure a gateway or local host as a BOOTP server by configuring a local static mapping table and enabling the BOOTP process. 3. Configure a device, such as a local host or a gateway, as a BOOTP proxy agent for the local segment. This first option is not a good idea because if you simply open up these ports on your router, BOOTP broadcast frames are forwarded. It negates the main purpose of having a router in the first placeto cut down on this type of traffic. With the second option, the BOOTP requests do not have to be forwarded beyond the local gateway. However, this option does add overhead to what perhaps is an already overburdened gateway. Use this option for a local host running the BOOTP server process, offloading this process and its overhead from a gateway, which should be used only for datagram forwarding. The third option enables a local host or a gateway to intercept local BOOTP broadcasts and repackage them as directed datagrams, sending them directly to a BOOTP server or servers located on another segment. On behalf of the requesting host the agent sends the request as a unicast datagram or directed broadcast (subnet broadcast). This enables an administrator to control broadcast traffic on the internetwork yet still provides remote IP configuration to hosts needing it.
BOOTP header
A BOOTP Header and a DHCP header use the exact same format. Figure 4.12 shows the format of a BOOTP header; Figure 4.13 shows a BOOTP header as seen through a Sniffer. Note that within the Sniffer, the Opcode field is referred to as boot record type. The Sniffer also refers to the second field as elapsed boot time, the unused field as flags, the client IP address field as client self-assigned IP address, and your IP address field as client IP address. In addition, the Sniffer lists the unused field, referred to as flags, which will always
106
TCP/IP PRIMER PLUS
contain a value of zero (0000). This field also states no broadcast, which is not true. This should just be ignored.
FIGURE 4.12
Op Htype Hlen Hops
Notice that a BOOTP header contains 300 bytes. Both BOOTP and DHCP use the exact same header format.
Transaction ID Seconds Client IP Address Your IP Address Server IP Address Gateway IP Address Client Hardware Address (16 octets) Server Host Name (64 octets) Boot File Name (128 octets) Vendor-Specific Area (64 octets) Unused
Opcode field
Seconds field
Unused field
FIGURE 4.13
Remember that BOOTP and DHCP use the same header format.
Your IP address
IP Address field
107
OpOperation Code
This 1-byte field specifies the type of BOOTP datagram being sent. There are two types of Operation codes: Opcode 1 = BOOTP Request (sent by clients) Operation Code 2 = BOOTP Reply (sent by servers)
HtypeHardware Type
This 1-byte field identifies the hardware type resolved as Ethernet, Token-Ring, or some other network type. For example, Ethernet has a hardware type value of one (1), thus BOOTP expects an address of 6 bytes or 48 bits in length.
HlenHardware Length
This 1-byte field specifies the length in bytes of the hardware address that BOOTP expects as a result of address resolution. This value varies depending on the hardware type, indicated in the hardware type field.
Hops
This 1-byte optional field indicates that a client is retrieving remote boot information across a router or routers. This indicates the number of hops this datagram has taken. The client initially sets this value to zero. Gateways increment this value by one each time they forward a BOOTP request.
Transaction ID
Although BOOTP is connectionless it implements a transaction ID value. This allows a client to match its request with a server response. The client randomly chooses the transaction ID value. The transaction ID field has 4 bytes.
Seconds
Each BOOTP client sets this timer value upon initialization and notes the time a request goes out, measuring how much time has passed since the client booted up and is still expecting its configuration from a BOOTP server. If a BOOTP client does not receive a response within a certain amount of time, it attempts to retransmit its request, hoping for a response from a BOOTP server. Each BOOTP client process implements some type of timer mechanism that controls how long a client will wait and how long it will wait between requests before it retransmits. These values vary based on vendor implementations. If these timers expire the device times out, fails to initialize itself, and cannot participate on the network. The seconds field has 2 bytes.
Unused
The BOOTP does not use this 2-byte field.
108
TCP/IP PRIMER PLUS
Client IP Address
Upon the first client boot, this fields value will contain all zeros. If the client is diskless this field will always have a value of zero, because the client has no place to store previously used parameters. If the client is not diskless and has stored this information, this field will have the original IP address assigned by the BOOTP server, which the client has stored and would like to reuse.
Your IP Address
In a BOOTP request sent by a client the following situations apply: If the previous field (client IP address) contains all zeros, this field will not appear. This indicates that this client has never received an address from a BOOTP server. If the client knows its IP address and would like to continue to use this address, this field will contain the same value (the original IP address assigned by the server). In the BOOTP response, this value will have the IP address assigned by the BOOTP server to this client.
Server IP Address
If the client does not know the address of the server, this field will contain all zeros and not appear within the analyzer output screen. A field of all zeros occurs when a client has initialized for the first time or if this is a diskless client without a storage area. If the client has stored this information from a previous boot, this field has the IP address of the BOOTP server to which this message is being sent. If this is a BOOTP reply, this field has the IP address of the BOOTP server that responded to the request.
Gateway IP Address
When a new host sends its initial request, this field should contain all zeros. If the BOOTP client knows it must forward this request through a local gateway and knows the address of the gateway or relay agent, it adds this information. If the client does not know this information (perhaps it is its first boot), it broadcasts the request and the gateway or relay agent forwarding this datagram adds its IP address. If the BOOTP client has previously received its configuration from a remote BOOTP server and has stored this information, this field will contain the IP address of the gateway or relay agent it used previously.
Client Hardware Address

This field identifies the BOOTP clients hardware address. For example, if the BOOTP client has an Ethernet hardware address, this field will contain the 6-byte or 48-bit unique address burned into the Network Interface Card (NIC). This field can have up to 16 bytes.
Server Host Name

This optional value identifies the BOOTP server by name. The value specifies that a particular BOOTP server can respond. If this value is left blank, any server can respond. The field can have up to 64 bytes.
109
Boot File Name

This optional value identifies the name of a boot file that the BOOTP client can request from the BOOTP server to retrieve configuration information carrying remote initialization parameters for the host. When the server responds, it identifies the full path of the boot file. If the client leaves this field unspecified (blank), the server attempts to download a default boot file for the client. If no default file exists and this field is blank, the server returns only basic parameters to the client, such as IP address and gateway address, but no boot file. This field can have up to 128 bytes.
Vender Specific
This field contains a list of specific options the client is requesting or is being assigned. Specific parameters vary based on vendor implementation.
BOOTP Request and Reply

Take a look at a BOOTP client and server exchange. Figure 4.14 shows a BOOTP client request being broadcast to all BOOTP servers on the local segment. Notice the UDP port values are 67 for BOOTP, which is the server, and 68 for the client. Within the summary pane you can see that the client does not know its IP address (0.0.0.0) and is broadcasting this request to all hosts (255.255.255.255). Within the detail pane the only address this host knows is its hardware address (NATA000DF).
FIGURE 4.14
Both a BOOTP request and reply use the same header format. You can tell which type of exchange it is by looking at the Opcode value, 1 for request and 2 for reply. In this case, it is a request. If this was a reply, the server would be giving the client an IP address.
110
TCP/IP PRIMER PLUS
DHCP (Dynamic Host Configuration Protocol)

Just as the name implies, DHCP (Dynamic Host Configuration Protocol) is a dynamic protocol that provides devices such as hosts or gateways with IP configuration parameters. These parameters include logical IP address, gateway address, DNS (Domain Name Service) addresses, and many more. RFC 2131 defines DHCP and is the official standard in the industry today, replacing previous protocols such as RARP and BOOTP. As you might recall RARP was the first protocol within the Internet Protocol suite to provide this type of service and has three major disadvantages, which DHCP tried to eliminate: It uses a static addressing table, which means an administrator must manually create and maintain the tables. It uses broadcasts for facilitating the requests and replies. Because routers cannot forward RARP broadcasts, a RARP server has to be located on every subnet throughout the internetwork to service client needs. BOOTP, which replaced RARP, also implemented a static table mapping MAC (hardware) addresses to logical network layer addresses. However, routers can forward BOOTP requests and unlike RARP, responses can be forwarded across routers to remote BOOTP servers; therefore do not require BOOTP servers on each segment. DHCP, actually an extension of BOOTP, uses the exact same UDP port values (port 67 = DHCP server and port 68 = DHCP client). It also uses an identical header format for its request and response messages as BOOTP, with one exception: The Vendor Specific field has been renamed Options and has a variable length. Like BOOTP, routers can forward DHCP. DHCP and BOOTP have one main differenceDHCP does not limit itself to using a static mapping table; hence its dynamic nature. You can configure DHCP with static mappings of hardware addresses to logical IP addresses. This typically is the case when a specific IP address must always be given to a host or gateway. However, unlike RARP or BOOTP, DHCP can maintain a pool of IP addresses (also known as a scope or range) that is available for dynamic assignment to hosts or gateways. This enables hosts to be mobile and still obtain IP address and configuration necessary to participate on a segment when they initialize. A host or gateway can serve as a DHCP server maintaining the address pool and configuration as necessary. A network administrator defines a scope with a valid range of IP addresses and lease times, and configures additional information to be assigned to end devices as requested. These parameters might include the following: The IP address of a gateway to be assigned to an end host so it may communicate beyond its local segment. IP addresses for DNS servers. IP addresses for WINS servers.
111
Allocating Configuration Information

DHCP is client/server based. Clients send requests and servers send configuration parameters in response. DHCP supports three methods of allocating configuration information: AutomaticAutomatic allocation is the permanent allocation of configuration information, such as IP address to a client. DynamicDynamic allocation allows a DHCP server to provide a client with configuration information to be used for a specific period of time (limited use), typically identified by a lease value. This is the most common method of allocation. Dynamic allocation is ideal when you have mobile clients on a group of devices who must share a pool of addresses. This allocation method works by reclaiming unused addresses and reassigning them to new hosts as needed. This allows for more efficient use of the address pool. ManualThe manual allocation method, just as its name implies, requires an administrator to manually assign an IP address to a device. When you implement and design the network, you can choose a single method or a combination of automatic, dynamic, or manual. The method you choose depends on the implementation. Some implementations use one or a combination of the above methods to facilitate address and configuration allocation.
DHCP Messages
DHCP clients and servers exchange the following DHCP message types: Discover Offer Request ACK NAK Decline Release Inform Table 4.1 gives a description of the different DHCP client and server messages types.
112
TCP/IP PRIMER PLUS
TABLE 4.1
DHCP Client and Server Message Types

Description DHCP clients send the discover message upon the initial boot as a local broadcast to DHCP servers. DHCP servers send the offer message in response to a clients discover message. This message includes the set of configuration parameters being offered by the DHCP server sending the offer. More than one server can respond to a clients request, each with its own offer. Sent by clients in the following instances: Acknowledging and accepting receipt of a previous offer. If the client receives multiple offers from several DHCP servers, acceptance of a specific servers offer implies rejection of all others. Sent by a client to renew the use of parameters previously allocated and currently in use by this device. Request by client to extend the lease of previously assigned IP address. Acknowledgment sent by servers confirming the clients acceptance of this servers offer and providing the client with IP address and configuration parameters. Negative acknowledgement sent by servers indicating that configuration parameters previously requested by a client are invalid or unacceptable. Sent by clients to notify servers that another host or gateway is already using the allocated IP address. Sent by clients to notify servers that the client no longer requires the previously assigned IP address and configuration parameters, which releases the server. This allows the server to re-allocate this information to another host or gateway requesting configuration. Sent by clients that have been manually configured with an IP address, but require additional parameters stored on a DHCP server.
Message Type Discover Offer
Request
ACK NAK Decline Release
Inform
DHCP Message Exchanges

Four general message exchanges occur between DHCP clients and servers to facilitate the configuration of a new client. Client broadcasts a DHCP discover message to locate servers. All servers respond to the discover with a DHCP offer message. If you have multiple DHCP servers capable of responding, they all respond to a client discover message with a DHCP offer message.
113
The client selects a server and requests configuration by sending a DHCP request message. The client can include a wish list of parameters it would like to receive. The client then must choose which offer it would like to accept by sending a DHCP request bearing a specific servers IP address. The acceptance of this servers offer automatically implies the rejection of all others. In the request the client can ask for specific configuration parameters it would like to receive. The selected server responds with a DHCP ACK including the configuration information requested. The server then must provide all the requested parameters or a partial set of them. The server does so by including this information with a DHCP Acknowledgement message. The address assigned to the client must be valid for the subnet the host resides on. If the server cannot fulfill the clients request for specific parameters or the client requests invalid parameters, the server responds with a DHCP NAK (negative acknowledgement). Once the client receives the configuration information, it performs one final function: It verifies that this IP address is not being used by some other host on the network by generating an ARP request with the given IP address as the target. It hopes that this request will go unanswered; in other words, that no other host on the network claims to recognize this IP address. If a host does recognize this address, this address is already in use and is unavailable to this host. If this occurs the host sends a DHCP decline message to the server and restarts the configuration process. If the ARP goes unanswered, meaning the address is not in use by another host, the client keeps the IP address. At this point it has completed the client initialization process. The client now has enough configuration information to participate on the network. Figures 4.15, 4.16, 4.17, 4.18, and 14.9 show the four-phase message exchange between client and server. In Figure 4.15, we see in Frame 1 a DHCP client with an unassigned IP address of 0.0.0.0 broadcasting (255.255.255.255) a discover message to locate a DHCP server. In Frame 2 (161.69.97.200), a DHCP server replies by broadcasting an offer message. In Frame 3 the client accepts the previous offer and requests an IP address and configuration parameters by broadcasting a request message. In the Frame 4, the last frame, the server confirms the request and assigns the parameters to the client in a broadcast acknowledgement. As you can see, these frames are all sent by broadcast, not unicast. That is because the client does not have an IP address yet and is unable to accept any other type of datagram. Once the client has been configured, future exchanges will use unicast datagrams. In Figure 4.16 the address being resolved is a 6-byte Ethernet hardware address. A gateway or agent has not forwarded this datagram, so the hop count is zero. The client uses the transaction ID (87C6A131) to match this with the corresponding reply from a server. The client booted 768 seconds ago. The flag options indicate that this request was sent as a broadcast. Note that all logical addresses such as client, server, and gateway (or relay agent) are zeros because this client has not learned this information. However the client does know its hardware address and reports it as NwkGn1093F5E; it attempts to resolve this hardware address.
114
TCP/IP PRIMER PLUS
Frame 2 Frame 4 Frame 3 Frame 1
FIGURE 4.15
In this example we see the four-frame exchange that occurs between a DHCP client and server when a new client comes online.
Message type Opcode Hardware address type
FIGURE 4.16
Note that this is an Opcode 1 (shown in the Sniffer output as boot record type), indicating that this is a request, message type discover.
Transaction ID Flags
Hop count Seconds
Client IP address Your IP address Server IP address Gateway IP address Server name Boot File name
Client Hardware address Parameters Vendor information
115
The client has not specified the DHCP server name or boot file. The client has specified options it would like to receive within the vendor information field. Beneath the vendor information field it lists requested options identified by values. These represent the wish list configuration parameters the client would like to receive from the DHCP server. To learn which option codes represent what parameters, please refer to the DHCP options RFC.
FIGURE 4.17
Note Opcode field contains a value of 2, indicating a DHCP reply, message type 2, a DHCP offer. This is the response from the server.
In Figure 4.17 note the transaction ID matches the one previously used by the client in Figure 4.16. Also note the IP address offered to the client (161.69.97.201). Look at the parameter below the vendor information tag field to see what parameters are being offered to this host. As you can see, the server has given the client a subnet mask of 255.255.255.0, a T1 (60 second or one half the lease) and T2 (105 seconds) timer for lease renewal and the lease value itself, 120 seconds. The server also has identified itself (161.69.97.200), which the client uses in future renewal requests. In Figure 4.18 the Opcode field contains a value of 1 with a message type of 3, indicating a DHCP request. The client has accepted the DHCP servers previous offer message and accepts the offered parameters. Note the transaction ID matches the ID used in the discover and offer datagrams. This means it is part of the same four-phase process. In Figure 4.19 the Opcode field contains a value of 2 (a reply message) with a message type of 5, indicating a DHCP acknowledgement (ACK). The server completes the four-phase exchange by sending this final datagram. In this datagram the server confirms the clients acceptance of its offer and is not allocating the parameters to the client previously listed in the offer message.
116
TCP/IP PRIMER PLUS
FIGURE 4.18
This figure shows a DHCP request.
FIGURE 4.19
This figure shows a DHCP acknowledgement.
The specific parameters a host requests vary based on implementation. If the client is diskless, it performs this process upon each boot; if the client is not diskless, this occurs only upon the initial boot up or if its lease has expired. If the client is not diskless, this is not its first boot, and it has stored the previously learned parameters after completing the four message
117
exchange. If a client has a lease that has almost expired, the following two message exchanges occur upon each boot: 1. The client sends a DHCP request message to the original server that provided it with its configuration to request the continued use of the configuration parameters. 2. The server responds with a DHCP ACK confirming the request and renewing the lease. If the server does not respond in time or is unavailable, and the lease expires, the client releases its IP address and configuration parameters and immediately ceases to participate on the network. Figures 4.20, 4.21, and 4.22 show the two-phase process between client and server to renew its lease. In Figure 4.20 DHCP client 161.69.97.201 sends a DHCP request to DHCP server 161.69.97.200, asking to renew its lease of the previously assigned IP address and configuration parameters. Notice this exchange is not broadcast-based because the client already has an IP address and therefore has the capability of sending and receiving directed datagrams.
FIGURE 4.20
In the response frame (DHCP acknowledgement), the server renews the lease.
Note in Figure 4.21 the Opcode field contains a value of 1, message type 3, indicating a DHCP request. In the first part of this message exchange, the DHCP client sends a request to the DHCP server, asking the server to renew its lease. In Figure 4.22 the Opcode field contains a value of 2 (reply) with a message type of 5, indicating a DHCP acknowledgement. In this second part and final part of the message exchange, the DHCP server sends an ACK (responding to the clients request) to renew the clients lease.
118
TCP/IP PRIMER PLUS
FIGURE 4.21
Note that the DHCP client wants the server to renew its lease.
FIGURE 4.22
The DHCP server acknowledges the clients request.
If a client no longer requires the IP address to be assigned, it sends a DHCP release message to the DHCP server, which previously assigned this address notifying it that it can return this address to the pool. This message exchange makes this address available to other clients. Although an administrator might have already configured clients with an IP address, some
119
clients need specific parameters from a DHCP server to function on this subnet. When this occurs, the client sends a DHCP inform message on the local segment requesting additional configuration parameters. DHCP servers with valid configuration parameters for this host respond with a DHCP ACK message including this information. When the client receives a response, it adopts the use of the parameters given and initialization is complete.
Lease Duration
The administrator can configure the lease duration, measured in seconds, on the DHCP server. The lease value varies based on implementation. Static mappings on the DHCP server have unlimited lease values, as the mapping of hardware address to IP address is hardcoded and never changes unless manually modified. This permanently reserves a specific address for a client. Dynamic assignment of addresses usually includes a lease time, which governs how long a client may keep an IP address. If a client remains consistently active, the server continues to renew this lease for the clients use. However, if the lease expires because the client cannot contact a DHCP server, the client ceases using this IP address and cannot participate on the network. If this happens, the client must start the four-phase allocation process again, obtaining a new IP address from a DHCP server. Two-timer values configured on DHCP servers control lease expiration and extensions: T1 and T2. The T1 value typically has a 0.5 * lease value; it dictates when the client will attempt to contact the DHCP server to renew its lease. If left at the default value, this means the client starts trying when the lease is half over (a 0.5 * lease value). When this occurs, the client sends a DHCP request to renew in hope that the server responds and reassigns the IP address to the client. If the clients attempts to renew its lease go unanswered and it reaches the T2 timer (the lease is 87.5% over), the client, in a desperate attempt to maintain its participation as a network client, starts sending its DHCP requests out as broadcasts to any DHCP server in hope that they renew the lease. T2 value typically has a 0.875 * lease value. Of course, an administrator can change either value.
DHCP Header
A DHCP header looks and functions in almost the same manner as a BOOTP header. A DHCP header has one major difference from the BOOTP header: The Vendor Specific field contained in the BOOTP header has been renamed Options and has a variable length. Figure 4.23 shows the format of a DHCP header.
OpOperation Code 1 Byte

This field specifies the type of DHCP datagram being sent. There are two types of Operation codes: Opcode 1 = DHCP Request (sent by clients) Operation Code 2 = DHCP Reply (sent by servers)
120
TCP/IP PRIMER PLUS
FIGURE 4.23
Note that a DHCP header and a BOOTP header use the same formats.
Op
Htype
Hlen
Hops
Transaction ID Seconds Client IP Address (ciaddr) Your IP Address (yiaddr) Server IP Address (siaddr) Gateway IP Address (giaddr) Client Hardware Address (chaddr - 16 octets) Flags
Server Name (sname - 64 octets)
Boot File Name (file - 128 octets)
Options (variable length)
HtypeHardware Type 1 Byte

This field identifies the hardware type resolved as Ethernet, Token-Ring, or some other network type. For example, Ethernet has a hardware type value of one (1), thus DHCP expects an address of 6 bytes or 48 bits in length.
HlenHardware Length 1 Byte

This field specifies the length in bytes of the hardware address that DHCP expects as a result of address resolution. This value varies depending on the hardware type, which is indicated in the hardware type field.
Hops1 Byte
This optional field indicates that a client is retrieving remote boot information across a router or routers. This indicates the number of hops this datagram has taken. The client initially sets this value to zero. Gateways or relay agents increase this value by one each time it forwards a DHCP request.
Transaction Id (XID)4 Bytes

Although DHCP is connectionless, it implements a transaction ID value, which allows a client to match its request with a server response. The client randomly chooses the transaction value.
121
Seconds2 Bytes
DHCP clients set this timer value upon initialization and note the time when a request goes out, measuring how much time has passed since the client has booted up and is still expecting its configuration from a DHCP server. If a DHCP client does not receive a response within a certain amount of time, it attempts to retransmit its request, hoping for a response from a DHCP server. Each DHCP client process implements some type of timer mechanism that controls how long a client will wait and how long it will wait between requests before it retransmits. These values vary based on vendor implementation. If these timers expire, the device times out, fails to initialize itself, and cannot participate on the network.
Flags2 Bytes
The Flags field specifies whether the datagram was sent as a broadcast or unicast frame.
Client IP Address4 Bytes

Upon the first client boot, this fields value will contain all zeros. If the client is diskless, this field will always have a value of zero because this client has no place to store previously used parameters. If the client is not diskless and has stored this information, this field has the original IP address assigned by the DHCP server, which the client has stored and would like to reuse.
Your IP address4 Bytes

In a DHCP request sent by a client the following situations apply: If the previous field (client IP address) contains all zeros, this field also will contain zeros. If the client knows its client IP address and would like to continue use of this address, this value will contain the same value (the original IP address assigned by the server). In the DHCP response, this value will have the IP address assigned by the DHCP server to this client.
Server IP Address4 Bytes

If the client does not know the address of the server, this field will contain all zeros. A field of all zeros occurs when a client has initialized for the first time or this is a diskless client without a storage area. If the client has stored this information from a previous boot, this field has the IP address of the DHCP server to which this message is being sent. If this is a DHCP reply, this field has the IP address of the DHCP server that responded to the request.
Gateway IP Address4 Bytes

When a new host sends its initial request, this field should contain all zeros. If a local gateway or relay agent must forward the request to locate a remote DHCP server, the gateway or agent forwarding this datagram adds its IP address. If the DHCP client has previously received its
122
TCP/IP PRIMER PLUS
configuration from a remote DHCP server and has stored this information, this field will contain the IP address of the gateway or relay agent it used previously.
Client Hardware AddressUp to 16 Bytes

This field identifies the DHCP clients hardware address. For example, if the DHCP client has an Ethernet hardware address, this field will contain 6-byte or 48-bit unique address burned into the Network Interface Card (NIC).
Server Host NameUp to 64 Bytes

This optional value identifies the DHCP server by name. This value specifies that a particular DHCP server can respond. If this value is left blank any server can respond.
Boot File NameUp to 128 Bytes

This optional value identifies the name of a boot file that the DHCP client may request from the DHCP server to retrieve configuration information carrying remote initialization parameters for the host. When the server responds, it identifies the full path of the boot file. If the client leaves this field unspecified (blank), the server attempts to download a default boot file for the client. If no default file exists and this field is blank, the server only returns basic parameters to the client, such as IP address and gateway address; but no boot file.
OptionsVariable Length
This field contains a list of parameters requested by the client or granted by the server.
Summary
Four types of protocols are used for address resolution: ARP, RARP, BOOTP and DHCP. ARP dynamically resolves a remote hosts logical Network layer IP address to a hardware address for proper delivery. Upper-layer applications and processes need the ARP protocol to dynamically resolve Network layer addresses for proper data delivery. RARP dynamically resolves a hosts hardware address into a logical Network layer protocol address. RARP has the opposite function of ARP, although both are broadcast based and use the same header format and fields. RARP has two major disadvantages: Routers cannot forward requests and replies and an administrator must create and maintain a static mapping table regularly. Both ARP and RARP utilize IP for their delivery of requests and replies. BOOTP evolved to replace RARP and provides the same type of address resolution utilizing UDPnot IPfor delivery of requests and replies. Routers can forward BOOTP requests and responses, allowing BOOTP servers to be strategically placed throughout the internetwork without requiring a BOOTP server on each and every network segment. However, BOOTP still requires manual updates by an administrator.
123
DHCP, evolved to replace both RARP and BOOTP, is named by the industry as the official standard. DHCP stops the disadvantages of RARP and BOOTP by maintaining a pool of IP addresses, known as a scope or range that is available for dynamic assignment to hosts or gateways. DHCP uses nearly the identical header format as BOOTP and the same UDP ports67 and 68.
Review Questions
1. What type of address resolution does ARP perform and how does ARP go about resolving this type of address resolution? 2. RARP performs what type of address resolution and how does RARP go about resolving this type of address resolution? 3. What protocol did BOOTP evolve to replace and what are the differences between the two protocols? 4. What are the major differences between DHCP and BOOTP? 5. What are the different ARP cache mechanisms? 6. What is Proxy ARP? 7. What does the Opcode field specify in a ARP or RARP header? 8. What is the difference between shouting and routing? 9. Name the different DHCP messages types. 10. Name the DHCP message types that accomplish the initial four-phase configuration process between client and server.
CHAPTER 5
IP ROUTING

Basic Routing Principles Static Routing Default Routing Dynamic Routing Distance Vector Protocols Link State Protocols
IP Routing Basics
The purpose of routing is to forward user datagrams beyond the local segment across an internetwork to the destination. When hosts do not reside on the same local segment, routers must get involved in the forwarding process. The local host determines whether the destination host it wishes to communicate with resides on its local segment. The local host achieves this by comparing the destination hosts IP address to the sending hosts local mask. If the destination host is remote (not on the sending hosts local segment), the local host directs the datagram to the local gateway for forwarding. To properly deliver its datagram the sending host relies on any number of unknown gateways between itself and the ultimate destination. If multiple routes exist, hopefully the datagram takes the fastest, shortest path possible. This is where routing methods come in. Routers use several methods to route datagrams between source and destination. Typically, routers use a combination of the following routing methods to build a routers route table: Directly connected interface Static Default Dynamic
126
TCP/IP PRIMER PLUS
Directly Connected Interface

Directly connected interfaces are routes that are local to the router; that is, the router has an interface directly connected to the destination network to which it wants to forward a datagram. Directly connected routes are always the best method of routing because the router knows the route to this datagram firsthand and does not rely on some other means to learn this route, such as static or dynamic routing protocols.
Static Routing
Static routes are routes to destination hosts or networks that an administrator has manually entered into the routers route table. Static routes define a specific gateway or interface to use when forwarding traffic to a particular destination. Because this type of route has a static nature, it is not capable of adjusting to changes in the network. If the defined gateway or interface fails or becomes unavailable, the route to the destination fails. This type of routing method has the advantage of eliminating all traffic related to routing updates. Static routing tends to be ideal where the link is temporary or bandwidth is an issue, so you want to use this method for dial-up networks or point-to-point WAN links. You can implement static routes in conjunction with other routing methods to provide routes to destinations across dial backup links when primary links implementing dynamic routing protocols have failed. Also, static routes are preferable when there are few to no topology changes in the network and when a remote site has only one exit point from the network.
Note
Remember with static routing, you must manually configure each route into the routers route table. This includes any topology changes in the network.
You would not want to design an entire network with only this method because you would have to enter each route manually, which is highly impractical. In addition, if a link or a router within the internetwork fails, you would have to enter a new route. Meanwhile routers obviously cannot forward traffic to that destination because the original path has become invalid. Static routing can have extremely high overhead in intense administrative hours spent getting the network up and keeping it going. Static routes work better with small to very small networks with perhaps as few as 1015 links total; even then, dynamic routes offer so much more versatility.
Note
Increasingly companies are using static routes for exits at every remote site they have (sometimes up to 20,000 remote locations). Usually these companies have a core-distribution-access model with the distribution layer running OSPF and BGP and the access layer running all static routes. The primary reason companies do this is that the remote sites have only one way to go and dont require a dynamic protocol. However, this does expose the company if it ever decides to change its method.
Chapter 5 IP ROUTING
127
Remember that static routing has the following characteristics: Advantage of eliminating all traffic related to routing updates Ideal for point-to-point WAN links or dial-up networks Can use as backup when primary link fails Impractical to have entire network static Has disadvantage of extreme administrative overhead Better to implement on small networks
Default Routing
Every IP host needs to have a default route either manually configured or dynamically learned. Default routes provide end hosts a way out of their local subnet and provide gateways with a last resort if there is no other route in the gateways route table. Although capable, end hosts do not usually maintain their own local route tables; they rely on local gateways to forward traffic to remote hosts. For an end host to communicate hosts beyond its local segment, an administrator at least must configure it with an IP address of a gateway (known as the default gateway). Depending on the vendor implementation, you can configure end hosts to send datagrams to an alternate gateway if the first one on the list becomes unavailable. If an end host does not have a default gateway configured, it limits this host to communicating to hosts on its local segment only. Routers use default routing as a last resort. Gateways inspect received datagrams to identify the logical Network layer address of the ultimate destination. If a static or dynamic route exists within the gateways route table, it forwards the datagram. If the destination remains unknown; that is, no method of routing has resulted in a learned route, it forces the gateway to use a default route. Typically, administrators implement default routes on point-to-point or dial-up connections, linking a companys network to the outside world. You can implement dynamic or static routes within the companys network to facilitate learning of local link route information. You then can use a default route to direct all traffic outside your network regardless of destination. This is a good method because there are about 105,000 routes on the Internet and it would overwhelm gateways if they had to learn and maintain each one of these routes. By implementing a default route the gateway simply directs all traffic to unknown destinations through the default path, typically serviced by an ISP.
128
TCP/IP PRIMER PLUS
Dynamic Routing
There are many different types of dynamic IP routing protocols: Distance Vector (RIPv1, RIPv2 and IGRP) Link State (OSPF) Hybrid (EIGRP) Dynamic routing has the main advantage of automatically detecting and adjusting around failed links or routers, reducing the overhead involved with building and maintaining route information. Dynamic routing protocols fall into one of two main categories: IGPs (Interior Gateway Protocols) EGPs (Exterior Gateway Protocols) IGPs propagate network reachability and routing information within an (interior) autonomous system. EGPs allow a router in one autonomous system to advertise network reachability information to a router in another (exterior) autonomous system.
IGP (Interior Gateway Protocols)

Designed for implementation within a companys internetwork of Autonomous System infrastructure, IGPs allow routers to build and maintain route information pertaining to local subnets and networks. Consider the following as IGPs: RIPv1 and v2 (Routing Information Protocol) IGRP (Interior Gateway Routing Protocol) EIGRP (Enhanced Interior Gateway Routing Protocol)Cisco proprietary OSPF (Open Shortest Path First) A single company can run multiple IGP routing protocols within its internetwork. In general, IGPs work best in small- or medium-sized networks, although some might support large networks. We will discuss each one of these protocols in more detail in Chapter 6, Routing Protocols.
EGP (Exterior Gateway Protocols)

Designed for use between Autonomous Systems, EGP routing protocols (for example, BGP) connect different companies networks together. Typically, EGP protocols do not concern themselves with the IGP protocols running within the AS. They typically see the entire AS as a single entity. The prolific BGP does most of the routing work for the Internet, handling AS routes interconnecting thousands of autonomous systems. We will discuss BGP in more detail in Chapter 6.
129
Routing Protocols and Best Path

No matter what type of routing protocol, once a router has determined what it believes to be the best path to the destination, it installs this route into its route table to forward datagrams. When a router receives a datagram, it inspects the destination IP address within the IP header to determine where this datagram is going. It checks its local route table to see whether it has a route to this destination. If it has a route, it identifies which local interface it will use to transmit this datagram en route to its destination. It also identifies the IP address of the next hop gateway that interfaces in the path to the destination. If the router does not have a specific route in its route table, it uses the default route. If the default route does not exist, it trashes the datagram and generates an ICMP message to the source host stating the requested destination network, or host, is unreachable.
Distance Vector Routing Protocols

Distance vector routing protocols, such as RIP v1, v2, and IGRP, judge best path based on one valuedistance (measured in hops). These protocols utilize the distance vector algorithm: RIPv1 and v2, and IGRP. Typically, these routing protocols support only broadcasts, although RIP v2 does support multicasts. These broadcasts are sent out periodically based on timers. When a distance vector router comes on line, it sends a request to all other routers on the segment asking them to send their entire route tables. Thereafter, each router broadcasts its entire route table when its update timer has expired, whether a change has occurred or not. This adds unnecessary traffic to the network without adding any new information. When a router receives update information, it adds one hop to the previously advertised route and updates its local route table. It then waits for its update timer to expire before passing this information to all other routers and all other interfaces except the one on which it was received. Because timers control the propagation of route information, rather than triggered by an event, such as a failed link, it takes time for all routers to learn, adjust, and agree on changes in the network (known as convergence). Distance vector protocols have the following characteristics: Broadcast Classful routing, with the exception of RIPv2 (updates do not include the subnet mask) Timers control updates The entire table is always sent regardless of a change Subject to routing loops Best used in small to medium networks Maximum distance defines the diameter of the network Uses hops as its sole metric
130
TCP/IP PRIMER PLUS
If a router learns that a link is unavailable, it might not immediately notify its neighbors, withholding this information until its timer goes off. This opens the possibility for routing loops to occur and delays the detection and correction. Because of this, distance vector implementations must employ several loop avoidance mechanisms to minimize the routing loops and their adverse effects. When there are multiple active paths to a destination, a routing loop can occur. If there are misconfigured routers within the internetwork, the routers might pass bad route information to a neighbor router, causing the receiving router to reinstate a dead route. In addition, a router can learn that a route is down, and although ready to notify other routers, it must wait for its timer to expire before doing so. Because of this, another router could receive an update from a router that this route is good. In turn, the router believes this information and reinstates the route in its table. What both routers might not know is that they think the path to the route is through each other (which causes routing loops). This happens because when distance vector routing protocols advertise route information, they include only the destination route and how far it is (in hops) from the advertising router. These updates do not include the subnet mask (except RIP v2) and the gateway or path this router is using to forward traffic to this network. To avoid routing loops, you can employ several methods, as discussed in the following sections.
Split Horizon
The split horizon rule states that a gateway must not advertise route information it received through an interface back out the same interface. It can only advertise routes learned in one directionout all interfaces other than the one through which it was received. This prevents feedback from occurring. You can think of split horizon as the old grape vine game you played as a kid, in which someone tells you a secret and you pass it on the next person in line and so on. After being told a secret, you would not tell the secret to the same person who just told you the secret because they already know it. The same applies to a gateway. With split horizon, a gateway will not tell a secret (send datagrams) to the same person (interface) from whom it learned the secret. It will send the information only to others (interfaces) who dont yet know that information.
Poison Reverse
Poison reverse allows a router to basically break the split horizon rule by advertising information it learned from an interface out the same interface. However, the routes learned through this interface would be advertised back out this interface with a hop count one greater than the maximum value allowed, or infinity value (RIP 16 hops, IGRP 256 hops). Routers with better metrics to this route simply ignore this, keeping their current route to this network in their route tables.
Count to Infinity (Maximum Hop Count) and Hold Down

Distance vector routing protocols determine the best path based on distance to each destination. Each protocol defines a maximum distance supported to a destination. Distance vector
131
protocols measure distance in hops with RIP having a maximum distance of 15 hops and IGRP, 255. Routers consider routes further than the maximum and do not forward datagrams to routes beyond the maximum hop distance. Routers exchanging route information advertise the destination network or host and the distance to that network. Routers receive this information, update their tables, and add another hop to the route (considering it one hop farther than the advertised route they received). Using RIP as an example, when route information propagates from one router to another, each router increments this value (hop count) until a router receives an advertisement with a hop count of 15. Adding a hop count to an advertisement with a value of 15 exceeds the maximum distance value, making the destination unreachable at 16 hops or more. This router then would advertise it with an infinity hop count in its next advertisement. The router trashes any datagrams destined for this network that it considers unreachable (exceeds maximum hop count). By keeping infinity low this enables routers to deal with routing loops within the internetwork and discard endlessly looping datagrams. If there is a loop in the network and routers keep feeding each other bad routes, the count to infinity allows the detection of this bad information, eventually killing the route to this destination. A router begins a count to infinity when it receives a route advertisement from a neighbor router stating that it can reach a network. In this example, this router (Router A) knows a destination route is dead. It prepares to advertise this information with its neighbors when it receives a route advertisement (from Router B) stating that it can reach that destination network with a hop count of 4. However, Router As path to the dead network was through Router B. Router A does not know that Router B thinks it can get to this network through Router A (perhaps split horizon is disabled). The receiving router (Router A) does not know the path Router B will use to reach this network; it knows only that the sending router (Router B) thinks it can get to this network. Router A has no choice but to treat the route information as reliable and adds the route to its table, adding a hop count (5) to the route. Unfortunately, these routers do not have the proper configuration, so Router A readvertises the route back out the same interface, stating that it can reach this destination in 5 hops. The original sending router receives it and assumes if this router advertises that it can reach this network within 5 hops, it can reach it in 6 hops (incrementing the hop count by one). This continues with each router updating its information, adding hops until they exceed the maximum hop count. Once they exceed the maximum hop, they kill the route. Meanwhile the datagrams these routers forwarded to the destination network (which they couldnt actually get to) loop back and forth between these routers until it exceeds the maximum hop count. At this time one of the routers trashes the datagram and sends an ICMP destination unreachable message back to the source host.
Link State Routing Protocols

Unlike distance vector protocols, which judge best path on distance, link state protocols can make more intelligent route decisions using one or a combination of metrics describing the state of the link, including
132
TCP/IP PRIMER PLUS
Bandwidth Delay Reliability Load MTU OSPF considered a link state routing protocol, is capable of supporting route decisions based , on these parameters, although typically it defaults to implementing only one of them bandwidth. Routing protocols that understand these metrics use this information to derive the lowest-cost path to a destination when multiple paths exist. These metrics actually appear within the IP header portion of a datagram; routing protocols supporting them can make use of this information. We described each metric in Chapter 3, Network Layer/Internet Protocols. Link state protocols exhibit the following characteristics: Multicast Triggered updates sent only when changes occur and include only the change Classless routing (updates include the subnet mask) Capable of ToS or QoS through bandwidth, delay, reliability, load, and MTU Best used in medium to large implementations Large amount of CPU time, memory, and resources to build and maintain route information Link state protocols do not use periodic timers to send updates. After the initial exchange of route information when they first come online, routers send only triggered updates (an event has occurred that changed the topology). In these triggered updates, the router sends only the changes, reducing the amount of update traffic generated. Routers send these updates through multicastsnot broadcastswhich reduces the amount of processing needed by all hosts on the local segment. Only devices belonging to the multicast group fully process the datagram. Link state protocols support classless routing (VLSMs) through the inclusion of the subnet mask within the route advertisement. By including the mask with the destination route being described, receivers can tell whether the destination address reflects a subnet or network. Other routing protocols, known as classful routing protocols (RIPv1 and IGRP), do not support VLSMs (classful routing); thus they do not include the mask in their advertisements. These protocols can assume only that a classful A, B, or C IP address is being used based on the value contained within the first byte because they have no other information to go by. Classful routing protocols do not include the subnet mask within their advertisements. This means receivers cannot tell whether a destination address has been subnetted; therefore they apply a classful default mask to derive the network portion of the address.
133
Hybrid Routing Protocols

Cisco Systems developed its own proprietary routing protocol, known as EIGRP (Enhanced Interior Gateway Routing Protocol). Cisco extended the IGRP distance vector protocol by adding link state characteristics to EIGRP. For this reason, Cisco classifies EIGRP as a hybrid. EIGRP has the capability of making more intelligent routing decisions than distance vector routing protocols. It uses one or a combination of the same metrics utilized by link state protocols to determine best path selection: Bandwidth Delay Reliability Load MTU EIGRP, although capable of supporting all of the previously listed ToS and QoS parameters, defaults to bandwidth and delay. It uses this information to derive the lowest-cost path to a destination when multiple paths exist. EIGRP shares many of link states characteristics: Multicast Triggered updates only sent when changes occur and only includes those changes Class routing (updates include subnet mask) Capable of ToS or QoS Best used in medium to large networks Supports multiple protocols: IP, IPX, and AppleTalk EGRIPs one unique characteristic is that it can maintain route information for three different protocol suites: IP, IPX, and AppleTalk. All other protocols mentioned in this chapter can maintain route information for only one. When a companys network includes more than one major protocol suite, they must implement multiple routing protocols to maintain routes for each. If a company has IP, IPX, and AppleTalk implemented, it would require three different routing protocols. Each routing protocol would generate route update traffic, adding a lot of overhead to a network. EIGRP solves this problem by enabling you to implement a single routing protocol to keep track of all the routes, drastically reducing the traffic on the network by offering features such as triggered and incremental updates. EIGRP, like link state protocols, do not use periodic timers to send updatesonly events trigger updates. Even then, it sends only the changes, reducing the amount of update traffic. EIGRP uses multicasts, not broadcasts, for its updates and supports classless routing (VLSMs) through the inclusion of the subnet mask within the route advertisement.
134
TCP/IP PRIMER PLUS
Summary
Routing forwards user datagrams beyond the local segment across an internetwork to the destination. When hosts do not reside on the same local segment, routers get involved in the forwarding process. Routers use directly connected interfaces, static routing, dynamic routing, default routing, or a combination to build route tables. Directly connected interfaces are the best method of routing because the router directly knows the route information. Static routing requires an administrator to manually configure and maintain the network. Every IP host needs to have a default route. Default routes provide end hosts a way out of their local subnets and gateways with a gateway of last resort. Dynamic routing automatically learns changes in topology and reduces the amount of time spent building and maintaining a network. Dynamic routing protocols fall into one of two categories: IGPs (Interior Gateway Protocols) or EGPs (Exterior Gateway Protocols). IGPs include RIPv1 and v2, IGRP, EIGRP, and OSPF EGPs . include BGP. IGPs allow interior autonomous systems to propagate routing information; EGPs allow exterior (another companys) autonomous systems to propagate routing information. Distance vector protocols use one metric to choose the best path, with the distance measured in hops. Distance vector protocols tend to have routing loop problems. You can use the following methods to prevent routing loops: split horizon, poison reverse, count to infinity, and holddown. Link state protocols can make more intelligent routing decisions and base best path on a variety of metrics.
Review Questions
1. What routing methods do routers use to build their routing tables? 2. What are the characteristics of static routing? 3. What are the characteristics of dynamic routing? 4. When would you want to use static routing and when would you want to use dynamic routing? 5. What does default routing provide? 6. What are the two main categories that dynamic routing protocols fall under and what is the difference between the two? 7. What five protocols are considered to be IGPs? 8. What are the characteristics of distance vector protocols? 9. What one metric does distance vector use and how does it vary between protocols? 10. What routing loop remedies for distance vector protocols can you employ? 11. How does split horizon work when enabled?
135
12. What five metrics are used by link state protocols to determine the best path? 13. What are some of the characteristics of link state protocols?
CHAPTER 6
ROUTING PROTOCOLS

RIP (RIPv1 and RIPv2) OSPF BGP IGRP EIGRP
Introduction to Routing Protocols

Routing protocols enable routers to dynamically learn paths to destination hosts and networks. This dynamic learning allows routers to adapt to changes in the network. Without some type of routing mechanism to learn about new or failed segments, routers could not forward datagrams. The purpose for every routing protocol, regardless of the type, is the same: to forward datagrams to their destinations. When a router receives a datagram, it identifies the destination network or host. It then uses this information and checks its local routing table to determine whether it has a known path to the destination. The path in the routing table identifies the local outbound interface that the router should use, as well as the next-hop router address to reach the destination. In Chapter 5, IP Routing, you learned about static and dynamic routing mechanisms. In this chapter, we will discuss the various dynamic routing protocols and how they work. Dynamic routing protocols enable Layer 3 devices, known as internetwork gateways or routers, to make intelligent and dynamic path selections. We will start with the IGPs (interior gateway protocols) used within a companys autonomous system and finish with BGP (Border Gateway Protocol), an EGP (exterior gateway protocol) that controls routing between autonomous systems.
138
TCP/IP PRIMER PLUS
RIP
Two versions of RIP (Routing Information Protocol) exist: version 1 (RIPv1) and version 2 (RIPv2). Both versions of RIP were originally designed around Xeroxs XNS and the routeD program that is integrated into the Berkeley implementation of Unix.
Note
Two Requests for Comments (RFCs) define RIP: RFC 1058 defines RIPv1 and RFC 2453 defines RIPv2.
RIP can run on end hosts or gateways. Although it runs on top of UDP (User Datagram Protocol) and IP (Internet Protocol), using UDP port 520, it functions as a Network layer protocol. RIP functions as an IGP, providing route determination within an autonomous system. RIP works best when implemented on small-sized networks because of its limitations, which we will discuss later in this chapter.
Note
An autonomous systems (AS) is a collection of networks that share a common routing protocol under a common administration.
RIP exhibits the following characteristics: It is broadcast based. It is an IGP. It works best on small-sized networks. It is a Distance-vector routing protocol. As a Distance-vector routing protocol, RIP implements the Bellman-Ford (also referred to as Ford-Fulkerson) algorithm to determine best path selection. RIP determines best path selection to a destination based on the shortest distance, measured in hops, between the source and destination. Although many other routing protocols today are capable of more intelligent and efficient route selection, RIPv1, second only to OSPF remains one of the most popular protocols. , As previously mentioned, two versions of RIP exist, RIPv1 and RIPv2. We will begin with a full discussion of RIPv1 and then discuss the differences between the two versions. RIPv1 is the most widely used routing protocol in the world today because of its simplicity. RIPv1 has the advantage of being easy to understand and implement. Although RIPv1 and RIPv2 have similarities, RIPv2 has added extensions that overcome some of the limitations of RIPv1. We will discuss RIPv2 later in this chapter.
Chapter 6 ROUTING PROTOCOLS
139
RIPv1
End hosts or gateways implement RIP to keep track of routes to destinations, such as hosts, networks, subnets, and default routes. End hosts or gateways learn routes to destinations via route updates that devices exchange dynamically on the local segment via periodic broadcasts. All devices that are running RIP listen on UDP port 520 and transmit from the same UDP port. On broadcast-based networks, such as Ethernet or Token-Ring, all devices receive these datagrams, but only devices listening on UDP port 520 process these datagrams. On WAN (wide area network) links, such as point-to-point links that do not support broadcasts, you must specifically identify and configure neighbors (that is, gateways) with each others IP addresses in order for exchanges to occur. RIP-enabled devices maintain local route databases (known as routing tables) that list all locally connected networks as well as networks that are both statically and dynamically learned via RIP neighbors. Initially this list only includes entries for local or directly connected networks, but after exchanging route updates with its neighbors, a router modifies the routing table to include remote routes learned from its neighbors. The routing table includes the following information: The IP address of the destination host, network, subnet, or default route (0.0.0.0). The IP address of the next-hop router en route to the destination. The metric (or cost) value, expressed as an integer between 1 to 15 hops that defines how far the network is from the device. The local interface that the host uses to forward the datagram to the destination and others. Each RIP host listens to updates and builds its database by adding one entry for each destination learned. Gateways advertise their entire routing table via broadcasts sent every 30 seconds. Each gateway maintains its own clocking mechanism, which controls when it sends updates. The gateway includes all known routes in its updates, in addition to the distance, in hops, to each destination. A gateway can include up to 25 entries in each update. If it has more than 25 entries, it must send further updates to send the remainder of the entries.
Note
Although hosts support RIP, you typically only find RIP enabled on gateways.
The broadcast nature of RIP, and the fact that one update may not be enough to advertise all routes, adds additional network overhead and traffic. Furthermore, gateways broadcast their entire table every 30 seconds, regardless of whether any of the route information has changed. When a gateway receives this update, it takes the following steps:
140
TCP/IP PRIMER PLUS
1. It adds all unknown routes to its routing table and increments the hop count value by one. 2. It replaces previous routes with routes that have lower metrics, where applicable. 3. It removes failed or unreachable routes. 4. It prepares to advertise this information to its neighbors on adjacent segments. Similar to how you might call friends on your cell phone to tell them about traffic conditions (such as which routes are available and how far away the route is), a router advertises what routes are available to destinations. When a gateway advertises a route, it states the IP address of the destination and the distance in hops. Receivers listen to these advertisements, learn from them, and incorporate the information into their local routing tables. When gateways incorporate a route in their routing table, they always increment the distance (that is, hop) value by one, indicating that the destination learned lies one more hop away from this gateway than the gateway from which it learned the route. After it includes this information in its routing table, the gateway advertises the routes contained within its routing table to all other neighbors connected to local segments and point-to-point links, advertising all the routes that it knows about.
Path Selection
RIP uses distance as the base metric to determine the best routethe shorter the distance, the better the route. When multiple routes exist to a destination, a router running RIP chooses the route that has the shortest distance (measured in hops) as the best route and installs it in the routing table; it then uses the information to forward future datagrams. RIPs simplistic approach to path selection doesnt always choose the best route to a destination. For example, say two routes to a destination exist: One of the paths is four hops away and consists of three 100 Mbps Ethernet links and one T1 WAN link. The other path is three hops away and consists of two 100 Mbps Ethernet links and a 19.2 Kbps WAN link (see Figure 6.1). Because RIP uses strictly distance to determine the best path, it chooses the path with three hops instead of the best paththe four-hop route that has a higher end-to-end overall transfer rate. If both paths had three hops, RIP would only consider the fact that both paths have the same hop count. In this case, RIP would try to load balance across these two paths, sending datagrams along both links. In this situation, due to the unequal transfer rates across the links, datagrams sent across the 19.2 Kbps link (the upper path) would slow the transmission process between remote hosts and might even cause connections to timeout and fail.
141
FIGURE 6.1
The path with the smallest number of hops is not always the best path. In this case, the best path is the four-hop route, which has a better overall transfer rate than the route with three hops.
Problems with Least Hops Which route do you want your data to take (Path A or Path B)?
3rd hop A 1st hop A 19.2 Kbps 2nd hop A Station X 2nd hop B 3rd hop B T1 link 1.544 Mbps 1st hop B 4th hop B Station Y
Unlike Link-state routing protocols, RIP does not take into consideration factors other than hop count, such as the following: Bandwidth capacity of a link Reliability Load Delay MTU (maximum transmission unit) RIP makes decisions based on a limited amount of datadistanceand this can pose a problem. Think about your commute to work. You might have a shorter commute (in terms of distance) if you take the surface roads. However, you might be able to take a longer route on the freeway and get to your destination more quickly (considering bandwidth, or the capacity of link). But there might be an accident on the freeway, and it might take four times as long to get to your destination. RIP doesnt concern itself with any data other than distance when determining the best path. Both versions of RIP have a maximum distance limitation of 15 hops, which equals the number of gateways a datagram can traverse. RIP considers a destination of 16 or more hops away too far, or unreachable. If a datagram traverses 15 gateways, the 16th gateway discards the datagram and returns an ICMP (Internet Control Message Protocol) message destination unreachable to the sender. (ICMP messages are discussed in Chapter 3, Network Layer/Internet Protocols.)
142
TCP/IP PRIMER PLUS
The RIPv1 Header and Fields

RIP uses two different message types: Routing information messages Messages that are used to request information Both message types use the same general header format: They have a fixed header, followed by a list of network (IP address) and distance (metric) pairs. The length of a RIP header depends on the number of network and distance pairs within the datagram. However, RIP datagrams cannot exceed a maximum size of 512 bytes or a maximum of 25 route entries. Maximum size (512 bytes) does not include the Data Link, IP, or UDP headers. Figure 6.2 shows the format of a RIPv1 message.
FIGURE 6.2
Command Version Must be zero Must be zero IP Address Must be zero Must be zero Metric May be repeated up to 25 times
In a RIPv1 message, a sequence of pairs appears after the general 32-bit header. Each pair has a network IP address and an integer that indicates the distance, in hops, to that network.
Address Family Identifier
The route and distance information fields repeat, depending on the number of routes being advertised, for example, if a gateway advertises five routes, two unused and metric fields repeat five times, one for each advertised route. The RIP datagram can carry up to 25 route entries within each datagram. The following sections describe the RIPv2 header fields.
Command
The 1-byte command field identifies the intended purpose of the frame (for example, a RIP request versus a response). Eight commands exist, and the one used depends on the kind of RIP message sent. Table 6.1 describes the commands and their meanings.
TABLE 6.1 Command 1
RIPs Command Messages

Meaning A request that a host or gateway sends upon initialization (or after the local routing table has been cleared), requesting that all neighbors respond with their routing information.
143
TABLE 6.1 Command 2
Continued
Meaning A response that provides route information and is sent by a host or a gateway in response to a RIP request. Or a regular periodic update sent every 30 seconds, advertising a hosts or gateways routes to its neighbors. An obsolete command that turns on trace mode. An obsolete command that turns off trace mode. A command that is reserved for Sun Microsystems internal use. An update request that is used with demand circuits. An update response that is used with demand circuits. An update acknowledgement that is used with demand circuits.
3 4 5 9 10 11
Version
The 1-byte version field identifies the RIP version as 1 or 2. RIP hosts and gateways must agree on which version type to use. RIPv1 devices do not support the extensions implemented by RIPv2 (that is, VLSM [variablelength subnet masks], authentication, or multicasting), so if both RIPv1 and RIPv2 exist on a network, there may be interoperability problems. However, RIPv2 hosts or gateways support the RIPv1 specifications, and in a mixed environment, they use the fields and values recognized by the lowest common denominator (RIPv1) to exchange route information with RIPv1 devices. You can configure RIPv2 routers to support RIPv1 or RIPv2 on a per-interface basis. If one interface connects to a segment where both RIPv1 and RIPv2 devices exist, you must configure for RIPv1 support on that interface. If another interface connects to a segment where only RIPv2 devices exist, you can configure for RIPv2. Although RIPv1 and RIPv2 have almost identical features, the RIPv2 extensions not supported by RIPv1 make the two versions incompatible.
Unused
RIPv1 has several 2-byte fields (the Unused field) that it does not use. These fields always contain zeros and repeat depending on how many routes the datagram carries.

Although RIP technically may support various Network layer protocols, the 2-byte address family identifier field only contains the value 2, which represents IP.
144
TCP/IP PRIMER PLUS
IP Address
The 4-byte IP address field identifies the address of the destination host, network, or subnet, or the default being advertised by the router.
Metric
The 4-byte metric field identifies the cost in hops, representing the distance to reach the destination network from the host or gateway that is advertising the route. The field should have a value between 1 and 15. If the field contains a value of 16, RIP considers the advertised route unreachable, due to a network link or gateway failure. Figure 6.3 shows an example of a RIP advertisement sent from a gateway.
FIGURE 6.3
A message containing a series of route pairs (IP address and distance metric) appears after the Address Family Identifier field.
Disadvantages of RIPv1
Despite being one of the most popular protocols in use today, RIP has the following disadvantages: It is broadcast based. It sends the entire table, even when no changes occur. Slow convergence due to periodic timers. It has a maximum distance limitation of 15 hops. It is prone to routing loops. It is a classful routing protocol and therefore does not support VLSM. Because RIPv1 is broadcast based, each gateway broadcasts its entire table every 30 seconds, even when no changes occur and there is no new or viable information. This adds unnecessary traffic to the network. Other routing protocols, such as Link-state routing protocols, use multicast advertisements and send updates only when a change has occurred on the network. The timer-based control slows convergence and the response to problems, such as routing loops.
145
When a gateway learns of a change in the network, such as the addition of a new link or notification of a failed link, it goes through the following process: 1. The receiving gateway incorporates the new information into its table and increments the hop count by one. This indicates that the gateway resides one hop further than the gateway from which it learned the route. 2. If the gateway learns of a failure, it updates the entry with a hop count of 16 and gets ready to remove the route. 3. The gateway waits for its periodic timer to expire before advertising, causing the gateway to send out this information with its regular updates. If the network has many gateways and segments, new information can take a while to reach all gateways throughout the network. In the meantime, the gateways operate with outdated and incorrect information. In addition, the maximum distance between any two communicating devices on an internetwork is 15 hops, which limits the diameter of the network and makes RIP an unacceptable routing protocol for medium to large networks. Routers cannot forward datagrams that have traversed or been forwarded through more than 15 gateways. When a router receives a datagram that has traversed more than 15 hops, it sends an ICMP destination unreachable message back to the sender, alerting it of the problem. RIP, like other Distance-vector routing protocols, is prone to routing loops, as described in Chapter 5. RIP implementations usually use a combination of routing loop prevention mechanisms, including the following: Count to infinityDistance-vector protocols limit the distance (in hops) that a datagram can traverse. If a route loop exists within the topology, the router automatically discards the datagram when it exceeds the maximum hop count (in this case 15), stopping the count to infinity (see Figure 6.4). HolddownKeeps a route in the route table even though it has been marked unreachable or possibly down. While in a holddown state, the network does not consider any further updates. When the router figures out the status of the route, it either flushes (that is, discards) the route or reinstates it. Split horizonRemember from Chapter 5 that split horizon dictates that a gateway or RIP-enabled host cannot advertise route information on the same interface from which the information came (see Figure 6.5). Poison reversePoison reverse allows gateways to break the split-horizon rule, by advertising information learned from an interface out the same interface from which it learned the information. It advertises the routes with an infinity hop value, indicating that the route is unreachable, and it thus poisons the route. Routers that have a route with a better metric (that is, hop count) to the network ignore the destination unreachable update (see Figure 6.6). Implementations vary based on vendor support and your specific configuration of RIP in the network.
146
TCP/IP PRIMER PLUS
FIGURE 6.4
Distance-vector protocols consider only the distance when choosing the best path for a datagram.
Counting to Infinity Each time a packet passes through a router, the hop count increases.
Router Hop 1 Router Hop 2 Router Hop 3
Packet
Maximum Hop Count (RIP = 15 Hops)
FIGURE 6.5
The middle router learns about networks 12.0.0.0 and 14.0.0.0 from the interface on the right and can only propagate this information out the opposite interface. It learns about networks 11.0.0.0 and 15.0.0.0 from the interface on the left and can only propagate this information out the opposite interface.
FIGURE 6.6
Split Horizon Routing information learned from an interface is never advertised back out that same interface.
15.0.0.0 11.0.0.0 12.0.0.0 14.0.0.0
14.0.0.0 12.0.0.0
11.0.0.0 15.0.0.0
Poison reverse allows a router to break the splithorizon rule.
Poison Reverse Routers use a metric of 16 for all network advertisements learned from that interface. The middle router will advertise out interface 1 that network 12.0.0.0 and 14.0.0.0 have a metric of 16.
15.0.0.0 11.0.0.0 12.0.0.0 14.0.0.0
12.0.0.0 hop = 16 14.0.0.0 hop = 16
147
RIPv1, which is a classful routing protocol, recognizes only classful IP addresses, such as Class A, B, or C addresses. It does not understand subnets and cannot identify subnets within a network because route advertisements do not include the subnet mask. Because route advertisements do not include the subnet mask of the destination being advertised, receiving gateways can only assume the default mask based on the address class being advertised. For example, in Figure 6.7, Routers A and B are RIPv1 routers. Router A advertises the classful network without including the subnet masks to Router B. Without the subnet mask information, Router B (which is not directly connected to the remote subnets being advertised) can only assume that this route is a Class B destination with a default mask of 255.255.0.0. Therefore, Router B thinks there are no subnets. This is incorrect, but without the correct mask, Router B cannot make any other conclusion.
FIGURE 6.7 Classful Routing
Router B 172.16.1.0 172.16.2.0 172.16.3.0 255.255.255.0 192.15.2.0 /24
Classful routing protocols, such as RIPv1, do not understand subnetting, which requires the use of VLSMs.
Router A 172.16.0.0 172.16.0.0
Classful Networks (RIP1 and IGRP) Router A sends a classful update without a mask. Router B does not learn about the subnets.
RIP Timers
RIP uses three timers to control routing updates: the periodic update timer, the invalid timer, and the holddown timer. RIP sends a periodic update every 30 seconds. It broadcasts its entire routing table, regardless of whether any change has occurred. RIP uses its invalid timer every 180 seconds. If a gateway does not receive a route advertisement that relates to a route in its routing table within 180 seconds, it considers the route invalid and marks it as such. RIP uses its holddown timer every 180 seconds. After a router marks a route as invalid because it detects a link failure or receives a lack of updates, the gateway starts the holddown timer. This suspends the reception of updates relating to this route until the timer expires. During the holddown period, the gateway does not listen to any advertisements from other gateways to reinstate the route. When the timer expires, the gateway either flushes (that is, discards) or reinstates the route. If it does not receive an advertisement from another gateway stating that
148
TCP/IP PRIMER PLUS
the route is valid, the gateway discards it. If the gateway receives an advertisement from another gateway stating that the route is valid, it reinstates it.
Controlling Route Update Traffic

Some RIP implementations enable an administrator to control the amount of RIP update traffic generated on a network. Implementations vary, so you should consult your vendor for specific application and configuration parameters. You can do the following to control RIP update traffic: Adjust the RIP timersYou can adjust RIP timers on RIP-enabled devices; for example, you can adjust the periodic update timer from 30 seconds to a greater value. Increasing the interval between updates cuts down on the amount of broadcast traffic on a network, but it slows convergence times. If you increase the interval, broadcast traffic increases, but convergence times are reduced.
Note
It is extremely important to note that all RIP-enabled hosts and gateways must agree on timer values for convergence to occur. On nonbroadcast networks, such as point-to-point or multipoint WAN links, each gateway must know the IP address of all other gateways with which that gateway will exchange RIP updates.
Configure gateways on a broadcast network by using neighbor statements Although this is seldom practiced, you can configure gateways on a broadcast network, such as Ethernet or Token-Ring, with neighbor statements, which causes the gateways to exchange updates as directed datagrams instead of broadcasts. However, this means that if the network adds or removes a gateway, you have to manually change these statements to facilitate route information exchange. Configure route update filtersProbably the most common and effective way of minimizing route update traffic is to configure route update filters on RIP-enabled devices to filter inbound or outbound updates on an interface. Filters typically consist of permit or deny statements that allow or disallow route information from being received or propagated. Because each RIP datagram can include only a maximum of 25 routes, a gateway with 27 routes to advertise must send two RIP broadcasts. If you could filter 2 of the 27 routes, you could effectively cut the number of broadcasts in half. Implementation of filters is vendor specific.
RIP and Demand Circuits

RIP uses demand circuits, or WAN links (such as ISDN or X.25 links), to provide bandwidth by establishing a link between remote sites when it needs to forward data, and it terminates the link when it no longer needs the transfer data. Demand circuits are ideal when low-volume or infrequent data transfers occur between remote sites or as backup links in case of primary link failure.
149
Because demand circuits activate only when needed and terminate when not needed, they conserve resources and reduce costs. However, the temporary nature of demand links does not work well with dynamic routing protocols. If a link goes down, gateways cannot exchange periodic updates, which means they lose their routing information. Without this information, routers cannot exchange data between sites. Typically to create demand circuits, an administrator enters permanent routing table entries by using static or default routing as the type of routing method. When the link initializes, gateways immediately know how to route data. This method adds no extra broadcast or multicast route advertisement traffic to the link. Modifications to RIP make the use of dynamic protocols possible on these demand circuits. RFC 2091 defines this modification, called triggered updates, which enables RIP to support dynamic routing over demand links. Triggered means that an event, not a timer, triggers the router to send an update. Gateways also use triggered updates. As mentioned earlier in this chapter, the use of neighbor configuration on each gateway connected to the link supports route update exchange. By specifying each gateways neighbor, RIP can send directed route updates to the gateway at the other end of the link without broadcasting. With demand links, the following events trigger RIP gateways to send updates: A gateway initializes and requests route update informationThe entire routing table is exchanged. A change occurs in the networkOnly changes in the network are sent. Link status transitions from up to down state or vice versaThese transitions may be the result of a gateway powering up due to demand. Some vendor implementations also include mechanisms that allow remote gateways connected to demand circuits to permanently or semipermanently store route information learned while the circuit is up. For example, Cisco implements Snapshot routing. As the name implies, gateways connected to the link take a snapshot of the routing table after they exchange route information. They then use this snapshot of the network to route traffic, maintaining this information statically while the link remains down. This enables routers to learn about remote networks and routes to those networks. Snapshots enable routers to keep information, even when links are unavailable.
Demand Circuit Packet Types

Triggered update supported across demand circuits requires the use of three additional RIP packet types and an extended 4-byte update header. Both RIPv1 and RIPv2 support all three packet types and the extended 4-byte header. Figure 6.8 shows the header format of the three additional RIP packet types that support triggered updates across demand circuits. Table 6.2 explains the three packets types.
150
TCP/IP PRIMER PLUS
FIGURE 6.8
Command
Version Update Header
Must be zero
Demand circuit packet types extend the RIP header by 4 bytes.
Zero (RIP) or Route Tag (RIPv2)
RIP Entries
Version
Must be zero
Version
Flush
Sequence Number
TABLE 6.2 Packet Type 9 (request)
Demand Circuit Packet Types

Description Sent by gateways to request update information Sent in response to a request; includes either the entire routing table or changed routes, depending on the initial request Sent to acknowledge receipt of update information contained within a response datagram
10 (response) 11 (acknowledgement)
Unlike in the connectionless LAN-based broadcasts, sequencing and acknowledgements help track demand circuit route exchanges. All RIP responses (type 10 packets) carry sequence numbers. Each response increments these sequence numbers by one. Gateways receiving these responses must acknowledge receipt of route information carried within the response datagram by sending an acknowledgement that has a matching sequence number. Gateways assume that unacknowledged datagrams are lost and that the sender will retransmit them.
RIPv2
RFC 2453 defines the RIPv2 specification as an extension to the original specification of RIPv1 (RFC 1058). RIPv1 and RIPv2 perform similarly. Designed to address some of the limitations of RIPv1, RIPv2 includes some enhanced features to support authentication and subnetting capability. Although some companies rarely use RIPv2, other companies have moved to RIPv2 where they need RIP (for example, with a PIX firewall), but they use RIPv2 because they also need VLSM support. Other routing protocols, such as Link-state routing protocols, have been developed to address RIPv1s limitations and offer much better route selection criteria, reduced bandwidth consumption, and faster convergence than RIPv2.
151
RIPv1 Versus RIPv2

Table 6.3 compares RIPv1 and RIPv2.
TABLE 6.3 RIPv1
RIPv1 Versus RIPv2

RIPv2 Broadcast or multicast Authentication Classless routing Distance-vector protocol Uses hops as the metric Maximum distance = 15 IGP
Broadcast only No authentication Classful routing Distance-vector protocol Uses hops as the metric Maximum distance = 15 IGP
Figure 6.9 shows the format of the RIPv2 header.

FIGURE 6.9
Command Version Must be zero Route Tag IP Address Subnet Mask Next Hop Metric May be repeated up to 25 times
The RIPv2 header contains a subnet mask and a Next Hop field, which are zeros in the RIPv1 header.
RIPv2 gateways exchange route information with each other by using multicast rather than broadcast advertisements, using the address 224.0.0.9. When RIPv1 and RIPv2 routers exist in the same network, support for broadcast capability allows for interaction. Unlike RIPv1, which does not support any type of authentication, RIPv2 allows assignment of a plain-text password, which enables low-level security to be implemented between gateways that exchange information. Figure 6.10 shows the format of an authenticated RIPv2 packet. If authentication information is included in the RIPv2 packet, the maximum number of entries is reduced to 24. Note that the Address Family Identifier field changes to FFFFH, and the Route Tag field identifies the authentication type.
152
TCP/IP PRIMER PLUS
FIGURE 6.10
Command FFFFH
Version
Must be zero Authentication Type
RIPv2 supports authentication, but RIPv1 does not.
Authentication (16 octets)
RIP Entries (24 maximum)
Including subnet mask information within route advertisements allows for classless routing. When a RIPv2 router advertises its route information to neighbors, it includes not only the networks it knows about but the subnet mask of each network. With this information, the receiving gateway can determine whether the network has been subnetted. RIPv2 does not limit itself, as RIPv1 does, to the recognition of classful addresses. VLSM support allows a classful address and its subsequent subnets to easily be determined and advertised.
RIPv2 Compatibility with RIPv1

RIPv2 is considered to be backward compatible with RIPv1 gateways. However, for RIPv1 and RIPv2 gateways to exchange information, they must use the lowest common denominator, which means they must be broadcast only, have no authentication, and use classful addressing only. This, of course, negates the benefits of RIPv2. If you have RIPv1 and RIPv2 implemented on the same subnet, RIPv2 devices must adhere to RIPv1 standards and limitations. If, on another interface, one of these RIPv2 devices connects to a subnet that has RIPv2 peers, it can use RIPv2 on that interface. Configuration of RIPv1/RIPv2 support varies, depending on vendor specifications, but typically you configure on a per-interface basis.
OSPF
As mentioned in Chapter 5, OSPF (Open Shortest Path First) uses a Link-state Algorithm (LSA), and therefore, it makes more intelligent path selection than Distance-vector routing protocols. When making routing decisions, OSPF like all Link-state routing protocols, consid, ers any or all of the following: Link capacity (bandwidth) Delay Reliability Load MTU
153
Note
Although two versions of OSPF existversion 1 and version 2we will discuss version 2 only because version 1 is considered obsolete.
In addition, OSPF offers several advantages over Distance-vector routing protocols, including the following: It is able to configure hierarchical (instead of flat) routing domains by dividing an autonomous system into multiple areas. This isolates changes, routes update traffic to different areas, and reduces overhead involved with routing table recalculations. It is able to adapt quickly to internetwork changes with triggered updates. It sends only changes, not the entire table. It supports large networks. It supports load balancing of traffic over redundant equal- and unequal-cost paths. It authenticates routing table information exchanges. It supports VLSMs. It uses multicasts rather than broadcasts. Designed as an IGP, OSPF can support medium to large networks within a single autonomous system. An OSPF autonomous system, within the context of this discussion, refers to single or multiple OSPF areas and the routers within these areas that are used within an organizations internetwork. THE IETF (Internet Engineering Task Force) originally developed OSPF (defined in RFC 1247 and replaced by RFC 1583), which only supports the routing of IP datagrams, identified by IP type 89. OSPF makes routing decisions based on the logical Network layer address of the destination and ToS (Type of Service) bits within the IP header, which offers Quality of Service (QoS) routing to upper-layer applications and services as needed. OSPF routers detect route failures and adapt quickly to changes in the network. When a router detects a link failure, it triggers an update that is flooded to all routers within the OSPF area to notify them of the failure. In contrast, Distance-vector routing protocols, wait for their periodic timers to expire before sending updates. When a problem occurs, an OSPF router immediately generates a multicast advertisement and floods it out all OSPF ports, notifying all routers within its area of the downed link. All routers compute route changes in parallel, which speeds convergence times. We will discuss the operation of OSPF as it relates to a single area, and then move on to a more complex autonomous system that involves multiple areas in a hierarchical structure.
154
TCP/IP PRIMER PLUS
OSPF Characteristics
OSPF is characterized by the following: Multicast224.0.0.5 for all OSPF routers and 224.0.0.6 for designated router (DR)/backup designated router (BDR). Fast convergenceRouters immediately flood updates when a change occurs, and they compute calculations in parallel. Triggered updatesRouters send changes immediately, without waiting for a periodic timer. Classless routingOSPF supports VLSMs. ToS or QoSOSPF routers can forward datagrams to a destination, based on the level of service required by the application. AuthenticationRouters can use password protection, which enables them to exchange information only with authorized routers. Equal- and unequal-cost routesRouters can forward datagrams across redundant equal- and unequal-cost paths to a destination to balance the load of traffic. AreasOSPF can be implemented in a single area or divided into multiple areas. Subdividing an autonomous system into areas reduces the amount of update traffic. (Link-state database and SPF calculation are discussed later in this chapter.) OSPF supports VLSMs through the inclusion of subnet masks within updates. OSPF routers not only advertise the destination network or host, but they include the subnet mask, allowing the receiver to identify subnetted networks. OSPF supports IP ToS through the recognition of the bits set within the IP header that enable OSPF routers to forward datagrams to a destination based on the level or class of service required by the application. OSPF support for IP ToS is vendor specific. OSPF primarily relies on the following complex metrics for best path selection: Bandwidth Delay Reliability Load MTU Although OSPF routers can support any or all of these, unless specifically configured to do so, routers typically default to bandwidth only. You can modify any of the metric values to identify the cost parameter by which a router determines the best paththe lower the cost, the better the route. Administrators may configure different cost values on different interfaces of a router. If multiple paths exist to a destination with different metrics, lower-cost paths are placed in the
155
routing table as the preferred route. When IP ToS is in use with redundant paths that offer different types of service, routers place multiple routes within the routing tableone for each ToS. When multiple paths exist and have the same cost, routers can use both routes to forward datagrams; this is referred to as load balancing.
OSPF Databases
All OSPF routers maintain and build three separate databases: Adjacency databases (that is, neighbor tables) Link-state databases (that is, topology maps) Forwarding databases (that is, routing tables)
Adjacency Databases
For an OSPF router to exchange and learn about routes, it first forms an adjacency with its directly connected neighbors on the local segment. If it does not form this relationship, it cannot participate in OSPF routing. For an OSPF router to form an adjacency when it first comes online, it goes through the following steps: 1. It transmits Hello packets out on the local wire to identify itself to its neighbors. 2. Receiving OSPF routers add the new router to their adjacency databases and respond to the Hello packet with their own Hello packet, to identify themselves. All neighbors should know about each other and have theoretically formed a neighbor relationship. This is a very simplistic view of the process because it assumes that all required parameters within the Hello packet match and that the neighbors agree on them. If this is not the case, the neighbors will not form an adjacency. We will discuss the Hello packet and other packets types later in this chapter.
Link-state Databases
When OSPF routers know with which routers to exchange information, they can build a Linkstate, which is a complete map of the internetwork topology of the OSPF area, to identify every network and subnet and the path to each. From this database each router creates a tree structure identifying itself as the root connected to each destination through the shortest path.
Forwarding Databases
A forwarding database, or routing table, uses the link-state database to form its database. When each router has a complete topology map, it can run the SPF algorithm to determine the best route to each known destination. It then places these routes in its local routing table so that it can forward data.
156
TCP/IP PRIMER PLUS
OSPF Operation
OSPF can support various Data Link layer architectures, such as LAN and WAN connections. How adjacencies and database exchanges take place depends on the architecture over which OSPF runs. For the purposes of this section, we focus on LAN-based (broadcast) architectures. We describe other architectures later in this chapter. Lets start by discussing OSPF operation within a single area. When only a single area exists, the OSPF autonomous system and area are one in the same. All routers within an OSPF area maintain a copy of the same Link-state database (see Figure 6.11). When multiple areas exist, routers connected to all the areas maintain separate databases for each area.
FIGURE 6.11 Single Area OSPF
In a single-area OSPF implementation, all routers within the area maintain three databases: a topology map, a neighbor table, and a routing table.
OSPF has six different Link-state advertisements (LSAs), grouped into three categories: Intra-area advertisement Inter-area advertisement External advertisement Each of these categories describes the type of advertisement and where its propagation occurs. Table 6.4 describes the six different packet types.
157
TABLE 6.4
LSA Types
Advertisement Name (Type) Router link (intra-area) Description Describes the routers directly connected network and the state of the interfaces Identifies all routers that are connected to the local network Summarizes the routers subarea to a network outside the area Summarizes routes to external nonOSPF networks outside the autonomous system Describes a route to a destination in another autonomous system Carries route information through a stub network
Link-state Type 1
2 3 4
Network link (intra-area) Summary link (inter-area) Summary link (inter-area)
5 7
Autonomous system external link (external) Autonomous system external link (external)
Intra-Area Advertisement
Routers send intra-area advertisements within an area. These advertisements only propagate within the area of origination, and they describe local router links and networks within an area. Routers flood Type 1 (originated by all routers) and Type 2 (originated by DRs only) advertisements throughout a single area only. There are two types of intra-area LSAs: Type 1 (router link) Type 2 (network link) Routers send Type 1 advertisements to the destination multicast address 224.0.0.6 (DR and BDR multicast group address). These advertisements describe their directly connected networks and the state of the interfaces connected to these networks. On LANs (broadcast networks), the DR sends a Type 2 advertisement to the destination address 224.0.0.5, the multicast group address for all OSPF routers. These advertisements identify all routers connected to the local network. Figure 6.12 shows an example of a Type 1 intra-area LSA and Figure 6.13 shows an example of a Type 2 intra-area LSA.
158
TCP/IP PRIMER PLUS
FIGURE 6.12
All routers send LSA Type 1 intra-area LSAs to the destination multicast address 224.0.0.5.
Link State Advertisements Type 1

Area 0 BackBone Area 51 ABR DR Type 1 Type 1 Type 1 Type 1
Router Link Advertisements: O (OSPF) Sent by all routers using 224.0.0.5
FIGURE 6.13
Only the DR sends LSA Type 2 intra-area LSAs to all routers on the same segment.

Area 0 BackBone Area 51 ABR DR
Type 2
Network Advertisements: O (OSPF) Sent by DR only using 224.0.0.6
Inter-Area Advertisement
ABRs (area border routers) send inter-area advertisements between directly connected OSPF areas. Typically, ABRs connect subareas to the backbone (Area 0), the main transit area for all inter-area traffic. These advertisements summarize the routes within an OSPF subarea. ABRs send these advertisements into Area 0, where other ABRs learn and then propagate the new inter-area information to their own areas. There are two types of inter-area LSAs: Type 3 (summary link) Type 4 (summary link) ABR routers also send summary link advertisements to summarize their sub-area into Area 0 (backbone). ABRs also use these advertisements to advertise summarized routes from other subareas learned through Area 0 into their own subareas.
159
ABRs send Type 4 LSAs to identify ASBRs (autonomous system boundary routers) that provide access to external non-OSPF networks outside their autonomous systems. Figure 6.14 shows examples of Type 3 and Type 4 inter-area advertisements.
FIGURE 6.14 Link State Advertisements Type 3/4
External AS (RIP)
ABRs send LSA Type 3 and 4 inter-area summary advertisements.

Area XX ABR
Area 0 BackBone
Type 4 ABR
ASBR
Area 51 Type 3 Type 3
Summary Advertisements: IA Inter-Area Type 3: Sent by ABRs into Area 0 summarizing their local area Type 4: Used to identify route to ASBRs
External Advertisement
Only ASBRs send external advertisements. These advertisements propagate throughout the entire OSPF autonomous system, except for stub areas, which are described later in this chapter. These advertisements describe external non-OSPF routes that are outside the autonomous system. An example of an external route would be a RIP route that is being injected (that is, redistributed) into OSPF to be advertised within the autonomous system. Because RIP is not OSPF OSPF considers this information foreign and advertises it as such. (External route injec, tion is beyond the scope of this book and its configuration varies based on vendor implementation. In this book we will simply refer to an external route as any route that OSPF cannot natively learn.) There are two types of external LSAs: Type 5 (external link) Type 7 (external link) Only ASBRs that are running more than one routing protocolsuch as OSPF and RIP, IGRP, EIGRP, and static routingsend Type 5 LSAs. An administrator can configure OSPF ASBRs to inject non-OSPF routes into the OSPF environment. The Type 5 LSAs allow foreign routes to be advertised throughout the autonomous system, making them known to all other OSPF areas and routers. Only ASBRs connected to an NSSA (not so stubby area, described later in this chapter) and routers connected to a stub network that are running more than one routing protocol (such as
160
TCP/IP PRIMER PLUS
OSPF and RIP, IGRP, EIGRP, static routing, and so on) can send a Type 7 LSA. You can configure OSPF ASBRs to accept non-OSPF routes and inject them into the OSPF NSSA environment as Type 7 LSAs, which are used to carry the route information through the stub network. An ABR connected to Area 0 converts a Type 7 LSA to Type 5 before passing this information into the backbone. Figure 6.15 shows an example of a Type 5 external advertisement, and Figure 6.16 shows and example of a Type 7 external advertisement.
FIGURE 6.15 Link State Advertisements Type 5
ABR
ASBR routers send Type 5 LSAs to advertise external non-OSPF routes.

ABR
Area 0 Type 5 BackBone ABR
ASBR
External AS
AS External Advertisements: E1 & E2 Sent by ASBR; used to identify routes to external autonomous networks FIGURE 6.16
Similar to Type 5 advertisements, ASBRs use Type 7 advertisements to send external route updates describing nonOSPF routes through an NSSA area to reach Area 0.

ABR External AS RIP/ EIGRP
ASBR ABR Area 0 NSSA
ABR
BackBone
Area 3
Type 7
AS External Advertisements: Sent by ASBR only within NSSA area to advertise external AS routes
The LSA Header

A database description packet can include one or more LSAs. Each LSA header, which is 20 bytes long, has the same format and contains the same fields. Figure 6.17 shows the format of an OSPF LSA header.
161
FIGURE 6.17
LS Age
Options Link State ID Advertising Router LS Sequence Number
LS Type Link State Advertisement Header Length
An OSPF LSA header contains 20 bytes.

LS Checksum
The following sections describe the OSPF LSA header fields.
LS Age
The LS age field contains a value that is measured in seconds and indicates the time that has passed since the originating router sent the LSA.
Options
The options field contains the same option values described in the Hello packet. We discuss Hello packets later in the OSPF section of this chapter.
LS Type
The LS type field defines the type of LSA being sent as either intra-area (Type 1 or 2), interarea (Type 3 or 4), or external (Type 5 or 7).
Link-state ID
The value in the Link-state ID field identifies either the IP address of the originating router (LSA Type 1 and 4) or IP address of the network being advertised (LSA Type 2, 3, 5, or 7). This varies based on LSA type. Table 6.5 shows the Link-state IDs that exist.
TABLE 6.5 ID Value 1 2 3 4 5
Link-state IDs
Description Slave router ID DR IP address of the destination network being advertised ASBR router ID IP address of the destination network being advertised
Advertising Router
The advertising router field identifies the router that originated the advertisement.
162
TCP/IP PRIMER PLUS
LS Sequence Number
The LS sequence number field guarantees the delivery and receipt of database description (DD) packets. Each time an OSPF router sends an advertisement, the originator includes a sequence number that identifies the advertisement. We discuss DD packets in more detail in the OSPF section of this chapter.
LS Checksum
The LS checksum field verifies that the contents of the OSPF DD packet have not been damaged in transit.
Length
The length field contains the length of the OSPF datagram, in bytes.
OSPF Router States

As discussed earlier in this chapter, a router must form an adjacency (that is, become a neighbor) before it can exchange route information with neighbors. OSPF routers go through the following states, from beginning to end: 1. Down 2. Init 3. Two-way 4. Exstart 5. Exchange 6. Loading 7. Full You can easily remember the first and the last states. Down means OSPF is either not enabled on this router or the interface has been reset. In other words, this router cannot currently participate, or it is not currently participating, in route information exchange. In the Full state, the routing table has converged and the router can actively route datagrams. Routers must pass through all other states to get to Full. The following sections describe the states in detail.
The Init State

A router identifies itself to all its neighbors when you enable OSPF on an interface. It does this by generating a multicast Hello datagram, announcing itself and its parameters. At this point no adjacency between neighbors exists. Figure 6.18 shows an example of the Init state.
163
FIGURE 6.18
Init State - No DR
In the Init state, a router initiates the adjacency process with its neighbors.
Hello
Hello
Hello
Routers send Hello messages to establish adjacencies with neighbor routers.
In the Init state, no DR or BDR router exists because the DR and BDR election process has not yet taken place. The router passes through this state when an administrator initially enables OSPF or resets an interface. In this state, routers transmit Hello messages, announcing their presence to all other routers on the network. All routers send this advertisement to all OSPF routers on the same segment. Routers attached to the same subnet receive this Hello message and thereby learn of their new neighbor and can incorporate them into their adjacency databases.
The Two-way State

After a router receives response Hellos from the other local routers, adjacencies begin to form. Each router learns who its neighbors are and adds them to its local adjacency database. Adjacencies only form if the following Hello fields match: Area ID Hello and Dead timers Authentication Stub ID If any of these values do not match, neighbor routers will not form an adjacency and thus cannot exchange route information. (These are only a portion of the Hello parameters. We will discuss all Hello parameters in more detail later in this chapter.) Figure 6.19 shows OSPF routers using Hello messages to form an adjacency database. At this point each router on the local segment knows its neighbors and has established a bidirectional (that is, two-way) relationship (see Figure 6.20). The Two-Way state assumes that routers have received and exchanged the initial Hello messages and incorporated them into their adjacency tables. OSPF routers transmit Hello messages every 10 seconds to maintain neighbor relationships with local routers.
164
TCP/IP PRIMER PLUS
FIGURE 6.19
OSPF Hello Announcements
Routers use OSPF Hello messages to build the adjacency database.

Values must match on Adjacent Routers
Router ID OSPF Area-ID Neighbors Router Priority IP Address of D.R. Hello/Dead Timers OSPF Password Stub Area Flag ID
Hello
Note: If an authentication password is assigned, this too must match! FIGURE 6.20
Two-Way State - No DR
In the two-way state, routers on the same network have achieved a bidirectional relationship.
Router 1
Router 2 Router 3
Router 1 Router 3 Router 2
Router 3
Router 1 Router 2
Each router adds all other routers to their Database.
The Exstart State

After the Init and Two-Way states finish, all routers on the segment have enough information to elect a DR and a BDR. Each broadcast network (that is, LAN) elects a DR and BDR for each segment. The routers use two parameters, priority ID and router ID, within the Hello fields for electing a DR and BDR. The routers consider the priority ID first and the router ID second. The routers elect the router with the highest priority ID as the DR and the router with second-highest priority ID as the BDR. If all routers have the same priority ID, the router with the highest router ID becomes the DR and the router with the second-highest becomes the BDR. You can modify both of these parameters to manipulate the DR and BDR selection. The DR and BDR become the focal point of the segment. The DR and BDR have the following responsibilities:
165
Collect all route advertisements from the local routers Build the Link-state database Disseminate this information to all other routers on the same segment (DR only; BDR is on standby to do so if the DR cannot) All other routers become slaves to the DR and BDR, which are masters. The DR and BDR become the recipients of all router advertisements. Both the DR and BDR belong to the multicast group 224.0.0.6, to which all routers address their advertisements. When the DR and BDR exist, they both receive and process the local Type 1 router advertisements from all other routers on the segment. However, only the DR has the responsibility for distributing this information to the local routers, addressing them to the destination multicast group 224.0.0.5. The BDR remains in standby mode until the DR cannot disseminate this information. At that time, the BDR becomes the DR. If the DR fails, the BDR takes over, and if the original DR returns, it does not supersede the current router performing the DR role. Electing a DR for each segment reduces the number of adjacencies necessary throughout the internetwork, limiting the processing of OSPF multicast traffic that needs to be done by all routers (see Figure 6.21).
FIGURE 6.21 ExStart State
DR BDR
Think of the Exstart state as the state routers must pass through prior to starting their route information exchange.
Hello
All Routers send LSAs to the DR and BDR using multicast 224.0.0.6.
The Exchange State

As the name implies, during the Exchange state, all slave routers exchange route information with the DR and BDR. All slave routers transmit their route information to the DR/BDR address 224.0.0.6. Both the DR and BDR assimilate the database changes. However, only the DR manages the synchronization and dissemination of this information. The DR (master) transmits learned route information to all slave routers on the segment on multicast address 224.0.0.5 (see Figure 6.22).
166
TCP/IP PRIMER PLUS
FIGURE 6.22
Exchange State
DR - Master 224.0.0.5 BDR
The Exchange state allows routers to exchange their route information.
Slave
If any of the previous states fail, a topology map will not be built at this point. The first time a router enters this state, it has an empty Link-state database; therefore, it receives all route information to build the database. After that, routers send only updates to show topology changes. However, OSPF routers send all their route information every 30 minutes just to make sure that all OSPF routers have the current topology.
The Loading State

The router enters the Loading state only when it receives conflicting information with the DR during the Exchange state. If the information received differs from the currently held topology map, a router may enter the Loading state to send a Link-state request for more specific information to complete the map. If it finds no discrepancies, it skips this state.
The Full State

A router reaches the Full state after it passes through all the other states. In this final state the router builds the routing table from the topology map. The router derives and installs the best routes to destinations in the forwarding database by running the SPF algorithm on all routes identified within the Link-state database. Routers only transition through all these states when an administrator first enables OSPF and the routers have not actively participated in OSPF After a router has reached the Full state, it . only transitions through one of three states: Exchange Loading Full If something changes, the router generates a triggered update, and the exchange starts. If the router receives conflicting information after receiving an update, it enters the Loading state. In the Loading state, the router requests more information from the DR. After it receives the necessary information, it runs the SPF algorithm on the LS database, convergence occurs, and routing begins.
167
OSPF Router Types

OSPF defines different roles that routers assume based on their placement within the autonomous system. Remember that an autonomous system functions as a group of routers exchanging information via a common routing protocol (in this case, OSPF). A router can assume multiple roles at the same time. OSPF has four router types (see Figure 6.23): InternalAn internal router has all its attached interfaces contained within a single OSPF area. This type of router does not run any other routing protocol. BackboneA backbone router has at least one interface connected to Area 0. A router that has all interfaces within Area 0 functions as an internal backbone router. ABRAn ABR sits on the border of two OSPF areas. These routers connect to multiple areas, typically a subarea to Area 0. ABRs connecting to Area 0 also function as backbone routers. ABRs maintain multiple Link-state databases, one for each area to which they connect. ASBRAn ASBR sits on the boundary of two autonomous systems that run OSPF and some other routing protocol (any routing protocol besides OSPF), such as RIP. You can configure ASBRs to advertise non-OSPF routes into the OSPF autonomous system, to disseminate this external route information to all other areas within the autonomous system.
FIGURE 6.23 OSPF Router types
Area 66 Internal ABR Area 0 BackBone ABR Area 51 Internal
A routers placement within an OSPF network determines its type.
ASBR
External AS; RIP or Internet
OSPF Operation Over Various Data Link Architectures

As mentioned earlier, OSPF functions over various network types. However functionality differs based on the type of network it runs over. OSPF supports broadcast-based architectures as well as point-to-point and NBMA (nonbroadcast multiaccess) networks.
168
TCP/IP PRIMER PLUS
Broadcast
The broadcast-based LAN networks (Ethernet, Token-Ring, and FDDI) support broadcast and multicast traffic, allowing for the dynamic discovery of neighbors, election of DR and BDR, and route information exchanges (see Figure 6.24).
FIGURE 6.24 Neighbor Relationships on Broadcast Multi-Access Networks:
DR
Each broadcast multiaccess network has one DR and one BDR. Because these types of networks support broadcast and multicast traffic by default, neighbor relationships and DRs/BDRs are created automatically.
LSAs
Point-to-Point
A point-to-point, or dedicated leased-line, connection consists of two routers connected at each end of the link. In this environment, an administrator needs to manually configure a router with the IP address of its neighbor. This facilitates the ability to form an adjacency across the link and exchange route information. Because only two routers exist, there is no need to have a DR or BDR controlling the creation and synchronization of the Link-state database (see Figure 6.25).
FIGURE 6.25 Neighbor Relationships on Point to Point Serial Connections:
Point-to-point WAN links do not have a DR or BDR because a dedicated leased-lined connection has only two routers, one at each end of the link.
S0 S0
No DR or BDR election is required since there are only two devices on the link.
NBMA
NBMA (nonbroadcast multiaccess) networks consist of two or more routers communicating over a nonbroadcast network, such as X.25 or Frame Relay. Because NBMA does not support broadcasts, you need to manually configure each router with the IP address of all other neighbor routers in order for adjacencies to form. After you manually configure the routers with this information, they can elect a DR and BDR and exchange route information without the use of broadcasts.
169
If the underlying architecture supports broadcasts, then you need to manually configure neighbor information. If it does, then everything having to do with neighbor discovery, DR/BDR election, and route information exchange happens automatically (see Figure 6.26).
FIGURE 6.26 Neighbor Relationships Non-Broadcast Multi-Access Networks
NBMA networks do not support broadcast.

S0
S0
S0
Multiple Areas
You can implement OSPF in a single area for a small- to medium-size internetwork; however, most medium-size to large OSPF internetworks subdivide the autonomous system into smaller, more manageable subareas. A single-area implementation has one big disadvantage: As the number of networks and routers grows, so does the size of the Link-state database. When the Link-state database grows, it requires routers within a single area to keep track of changes to any router or network state change within that area. Storing and maintaining a large database requires a lot of memory and CPU time for all routers involved. Whenever a link within the area becomes unavailable or available, all routers within the area must recalculate the SPF algorithm for all routes within the database. When you divide an autonomous system into multiple areas, you reduce the amount of route update traffic by isolating it to each area and reducing the overall size of the routing table. Routers maintain databases only for areas they directly connect to, and this isolates intra-area route update traffic to the area where it originated. State changes affecting routes in one area do not require routers in other areas to recalculate. Because routers do not have to recalculate their routing tables when the status of a route in another area changes, this dramatically reduces the number of SPF calculations a router performs. You can break up an autonomous system any way you like, but typically design follows geography, with each physical location representing a subarea. When you use multiple-area design, the Area 0 (that is, backbone area) must exist as a major transit area for all inter-area traffic (see Figure 6.27). Just as all roads lead to Rome, all routes must lead to and through Area 0.
170
TCP/IP PRIMER PLUS
FIGURE 6.27
AS with Multiple Areas

Autonomous System Backbone Area 0
When multiple areas exist in an OSPF implementation, the entire OSPF routing domain is referred to as the OSPF autonomous system. All multiple subareas must connect to the main backbone transit area, known as Area 0.
Area 1
Area 3
Area 2
Routers within an area may only exchange information with routers in their same area. In Figure 6.27, there are three subareas1, 2, and 3all physically connected to Area 0 through ABRs, which summarize and advertise routes into the core, which in turn advertises the other areas route information into their own areas.
Area Types
Within a multiple-area environment, each area type defines the type of LSAs that it will accept and which router types will generate these LSAs. OSPF has three main area types: Backbone are (Area 0) Standard are Two stub areas (that is, standard stub and NSSA) Virtual links are not an area; however, virtual links provide a logical link between two areas through another.
Area 0
The backbone is the glue for all other areas. In addition to all intra-area advertisements that propagate within its own area, all inter-area summaries (sent by ABRs) and external autonomous system routes (sent by ASBRs) traverse this area en route to subareas. This area can accept all OSPF LSAs; therefore, it accepts all LSA Types 15 LSAs.
The Standard Area

The standard area functions as a subarea of Area 0. This area accepts intra-area Type 1 and 2 LSAs and inter-area summarized routes, Type 3 and 4, from other subareas sent by the ABR
171
connecting this area to the backbone. In addition, this area accepts external autonomous system routes advertised by an ASBR connected to the area (Type 5). You can have standard areas physically connected to Area 0 through multiple gateways, to provide redundant paths to and through the core.
Stub Areas
A stub area has only one way in and one way outthat is, a single connection to Area 0. You typically do not need to have OSPF updates sent across this link, especially if you have a slow WAN link or dial-up connection. Most often in this situation, you would use a default route to identify the path to networks outside a stub area. Configuring a default, or static, route eliminates update traffic on the link, conserving precious bandwidth. RFC 1583 defines two types of stub areas: Standard NSSA (Cisco Systems also has a proprietary stub area known as totally stubby, which we do not discuss in this book.) Stub areas have the following general restrictions: Area 0 and ASBRs cannot be part of a stub area. An administrator must configure all routers connected to or within a stub area or an NSSA network as stub routers.
Standard Stub Area

Although stub areas cut down on the OSPF advertisements sent into the area by implementing a default router, the standard stub area accepts intra- and inter-area routes (that is, LSAs of Type 1, 2, 3, and 4). This area does not accept any external route advertisements (Type 5 or 7) by ASBRs.
NSSA
NSSAs accept only intra-area (that is, Type 1 and 2) because without intra-area advertisements there would be no point to running a routing protocol if it could not at least learn routes within its own area. The NSSA does not accept external route advertisements (that is, Type 5 LSAs) by ASBRs. However, the name not so stubby area indicates that it allows something else into this area: It allows external routes to be carried through it en route to Area 0 as a LSA Type 7 generated by an ASBR. ABRs convert Type 7 external routes to Type 5 before advertising them into the core (see Figure 6.28).
172
TCP/IP PRIMER PLUS
FIGURE 6.28
NSSA - Not So Stubby Area
NSSAs carry external routes through into Area 0.
Remote Site
NSSA Area 1 Type 5 Type 7 ASBR injects RIP/EIGRP Routes into NSSA as LSA Type 7 ABR Translates LSA Type 7 into Type 5
Area 0
RIP/EIGRP
Central Office or ISP
In Figure 6.27, the NSSA (Area 1) directly connects to Area 0 via an ABR and to another nonOSPF routing domain (that is, autonomous system) via an ASBR. The ASBR connected to the non-OSPF routing domain runs the RIP, EIGRP, and OSPF protocols. The non-OSPF route information needs to be redistributed into the OSPF network at the ASBR. This causes the router to generate a type 7 LSAs into the NSSA. When these external LSAs get to the ABR connecting the NSSA to Area 0, these advertisements convert to regular external Type 5 LSAs and propagate throughout the rest of the OSPF autonomous system areas.
Virtual Links
Virtual links provide a logical path to Area 0 through a subarea, connecting either a new subarea to the backbone when a physical connection is impossible or when multiple Area 0s exist but are physically separate (for example, when two companies with existing OSPF implementations have merged). In either case, virtual links utilize a standard area as a transit path connecting the subarea to Area 0 or two backbones together. In Figure 6.29, a new OSPF area was added, but no way existed to connect it to the core. Area 3, used as the transit area, provides a virtual path to the core. In Figure 6.30, two departments with existing OSPF multiple-area implementations have merged. Both OSPF Area 0s need a link through a virtual path via a transit area, in this case, Area 51.
FIGURE 6.29 Virtual Link - Example 1
Virtual Link Area 3 Transit New Area not connected to Area 0 Area 0 Area 2
Virtual links are logical paths through subareas, connecting another area to Area 0.
Area 1
Virtual links create a logical path to Area 0.
173
FIGURE 6.30
Virtual Link - Example 2

Virtual Link Area 2 Area 51 Area 0 Area 0
Area 0 is the backbone.
Area 4
Area 1
Create a link between two backbones after merging networks.
Note
You must manually configure virtual links on border routers. Configuration varies depending on vendor implementations and is beyond the scope of this book.
Standard OSPF Fields

All five OSPF packet types (described later, in the section The Packet Type Field) have the same common fields within the 24-octet OSPF header (see Figure 6.31). One of these five packet types performs protocol operations. The OSPF header fields are described in the following sections.
FIGURE 6.31
Version Type Router ID Area ID Checksum Authentication AuType OSPF Packet Header Packet Length
The five OSPF packet types use the same standard header.
Hello, Database Description, Link State Request, Link State Update, or Link State Acknowledgement Header plus data
We will discuss the various packet types and look at their headers later in this chapter.
174
TCP/IP PRIMER PLUS
Version Number
The 8-bit version number field identifies the OSPF version number. Currently, OSPF uses RIPv2.
Packet Type
The 8-bit packet type field identifies the OSPF packet type. Table 6.6 lists the five different packet types and their protocol functions.
TABLE 6.6
OSPF Packet Types

Packet Type Hello Database description Link-state request Link-state update Link-state acknowledgement Description Establishes and maintains adjacencies Summarizes database content Requests specific route information or a complete update (that is, a database download) Sends route information in response to a request (that is, a database update) Acknowledges receipt of route information
Packet Number 1 2 3 4 5
A further discussion of the header format for various packet types appears later in this chapter.
Packet Length
The 16-bit packet length field identifies the length, in bytes, of the OSPF datagram, including the header and contents.
Router ID
The 32-bit router ID field contains a unique value that identifies the router that originally sent the OSPF packet. OSPF uses this value for DR and BDR selection. An administrator can manually configure the router ID, or it can be configured dynamically.
Area ID
The 32-bit area ID field identifies the area that the OSPF datagram came from. Area 0 always has an area ID of 0.0.0.0. This value varies for subareas, and an administrator can optionally configure the value to follow the subnet number of the subarea.
Checksum
The 16-bit checksum field verifies that the contents of the OSPF packet remain intact during transit. The Checksum field excludes the Authentication field when checking the integrity of the content of an OSPF packet.
175
Authentication Type and Authentication

OSPF routers optionally support simple password authentication. When configured to do so, routers form adjacencies with only routers that share the same authentication password. Together these two fields validate the packet. The Authentication Type field contains 16 bits and the Authentication field contains 32 bits.
Additional Headers
Every OSPF header contains an additional header that contains specific routing information about one of five packet types found after the common fields in an OSPF header: Hello packet (Type 1) Database Description packet (Type 2) Link-state Request packet (Type 3) Link-state Update packet (Type 4) Link-state Acknowledgement packet (Type 5) We discuss these packets and their headers in the following sections.
Hello Packets
Hello datagrams are OSPF Type 1 packets. Hello packets establish and maintain adjacencies. Figure 6.32 shows the basic format of a Hello packet. Figure 6.33 shows a Hello packet as seen through a Sniffer.
FIGURE 6.32
Version Type = 1 Router ID Area ID Checksum Authentication Network Mask HelloInterval DeadInterval Designated Router Backup Designated Router Neighbor Options Rtr Pri AuType OSPF Packet Header Packet Length
OSPF Hello packet fields include Network Mask, Hello Interval, Options, Routing Priority, Dead Interval, Designated Router, Backup Designated Router and Neighbor.
176
TCP/IP PRIMER PLUS
Router ID Hello (type 1) message Authentication
FIGURE 6.33
Only OSPF gateways with matching area IDs, authentication password, stub configuration, and Hello and Dead intervals will process information and form an adjacency.
Options capability
External routing capability bit set
In Figure 6.33, router 150.3.233.25 uniquely identifies itself with its router ID, which is used for BDR and DR selection. Remember that the router with the highest priority or router ID becomes the DR, and the next highest becomes the BDR. The area ID specifies the OSPF area from which the advertisement originated. If you implement authentication, which is optional, only gateways sharing the same password can form adjacencies. In Figure 6.33, the header lists the subnet mask for the gateway (255.255.255.0), along with the options it supports. A value of 1 in the Options Capability section of the header indicates that it supports that particular option. In this case, this router has the External Routing Capability bit set, as shown in the header. This indicates that this gateway supports non-OSPF advertisements and either an ASBR or a router within an area that supports external routes passing through it exists. In addition, this router identifies the IP address of the DR as 150.3.233.249 and announces itself as the BDR. Finally, this router lists the neighbors it knows of (in this case there is only one, 1.0.0.5). The Hello packet fields are described in detail in the following sections.
The Network Mask Field

The network mask field identifies the local interface subnet mask.
177
The Options Field

The options field specifies the OSPF capabilities that the router supports. All routers cannot support options. If they do not support the options, the router either rejects or ignores the options. The following two options are defined: T bitThis bit is used to indicate that this OSPF router can support ToS/QoS routing. ToS-capable routers indicate the level of ToS by setting this bit to a value greater than zero. A T bit set to zero indicates that the router does not have the capability to perform ToS routing. Routers enabled for ToS build multiple shortest-path trees, with themselves as the root: one for ToS-enabled routes that avoids non-ToS routers, and one for non-ToS routes (see Figure 6.33). E bitRouters with this bit set can process external non-OSPF route information. Stub area routers do not support external route updates and therefore do not set or recognize the use of this bit. ASBR routers always have the E bit enabled (see Figure 6.33). Table 6.7 describes these two options. Vendors may implement other option bits in the future.
The Hello Interval Field

The Hello interval controls how often the router transmits Hello datagrams. This value varies depending on the Data Link layer topology over which OSPF is running. On a broadcast network, routers send Hello packets out every 10 seconds. On a nonbroadcast network, by default, routers sends Hello packets out every 30 seconds.
The Router Priority Field

OSPF routers use the router priority ID exclusively for electing a DR and BDR for each segment. The router that has the highest priority ID becomes the DR. The DR controls the collection, synchronization, and dissemination of route information for the segment. The router that has the next-highest priority ID becomes the BDR. The BDR only collects and builds the Link-state database. It remains in standby mode until the DR fails. If this occurs, the BDR automatically promotes itself to DR for the segment, and the OSPF router then elects a new BDR. The default value for this parameter depends on the vendor implementation. If all routers have the same router priority value (that is, an administrator has not configured the default value higher on any gateway than on others), the router ID determines the DR and BDR for the segment.
The Dead Interval Field

The dead interval detects a failed neighbor. By default, a router considers a neighbor dead when it does not hear from a neighbor router (that is, no Hello packets are received) within four Hello intervals. The Dead interval has a value four times (in seconds) that of the Hello packet value. This value varies, depending on the Data Link layer topology over which OSPF is running. On a broadcast network, routers send out Hello packets every 10 seconds, which makes the Dead interval
178
TCP/IP PRIMER PLUS
40 seconds. On a nonbroadcast network, by default, routers send out hellos every 30 seconds, which makes the Dead interval 120 seconds.
The Designated Router Field

The designated router field lists the IP address of the DR, if it is known by this router. If the router does not know the IP address of the DR, this value appears as 0.0.0.0.
The Backup Designated Router Field

The backup designated router field lists the IP address of the BDR if it is known by this router. If the router does not know the IP address of the BDR, this value appears as 0.0.0.0.
The Neighbor Field

The neighbor field lists the router IDs of all neighbor routers that this router has learned about through local Hello packets.
OSPF Database Description Packets

Data Description packets (Type 2) convey data needed to initialize the topographical databases of adjacent devices. Figure 6.34 shows the format of the Database Description packet.
FIGURE 6.34
Version Type = 2 Router ID Area ID Checksum Authentication Interface MTU Options Sequence Number 0 0 0 0 0 I M MS AuType OSPF Packet Header Packet Length
OSPF Database Description packet fields include Interface MTU, Options, and Sequence Number, as well as an LSA header.
A Link State Advertisement Header
The Options Field

The options field describes the OSPF capabilities supported by the router. Although this field exists in other OSPF packet types, the bits mean different things, depending on the packet type in use. There are three bits within this field (see Table 6.7).
179
TABLE 6.7 Option I (Init) M (More)
Database Description Packet Options

Description When set, the I bit indicates that this is the first OSPF database description packet transmitted. When set, the M bit indicates that more of the Database Description packet should follow. If the M bit has a value of zero, it indicates the last packet. The MS bit identifies whether the transmitting router is a master (DR) or slave (all other routers): MS = 1 (router is master) MS = 0 (router is slave)
MS (Master/Slave)
The Sequence Number Field

The sender sequences all database description packets, and the receiver acknowledges each packet. The initial value of the Sequence Number field is uniquely chosen when the first DD packet is sent (Init bit = 1); thereafter, it is sequentially incremented.
The Link-state Advertisement Header Field

A router can include one or more LSAs within a Database Description packet. The specific fields are described earlier in this section.
Link-state Request Packets

OSPF Link-state Request packets (Type 3) get current route information or database downloads from a specific neighbor router. Figure 6.35 shows the format of a Link-state Request packet.
FIGURE 6.35
Version Type = 3 Router ID Area ID Checksum Authentication LS Type Link State ID Advertising Router AuType OSPF Packet Header Packet Length
OSPF Link-state Request packet fields include Link-state Type, Linkstate ID, and Advertising Router.
The Link-state Type Field

The Link-state type field identifies the LSA.
180
TCP/IP PRIMER PLUS
The Link-state ID Field

The Link-state ID field further describes the LSA. It assigns the LSA a unique identification that is used by other routers.
The Advertising Router Field

The advertising router field identifies the router that originally sent the LSA.
Link-state Update Packets

OSPF Link-state update packets (Type 4) route information sent in response to a request (that is, a database update). These packets contain information about the condition of various links within an internetwork. A single Link-state Update packet can include several LSAs (described earlier in this section). Figure 6.36 shows the format of a Link-state update packet.
FIGURE 6.36
Version Type = 4 Router ID Area ID Checksum Authentication # Advertisements AuType OSPF Packet Header Packet Length
OSPF Link-state update packet fields include Number of Advertisements and Linkstate advertisements.
Link State Advertisements
The Number of Advertisements Field

The number of advertisements field identifies the number of LSAs included in the update packet.
The Link-state Advertisement Field

The Link-state advertisement field makes up the bulk of the Link-state update packet. This field contains a list of LSAs. Each Link-state advertisement field has a common header, followed by one of six LSAs. A complete list of LSAs and description of fields appears earlier in this chapter.
The Link-state Acknowledgement Packet

The Link-state acknowledgement packet (Type 5) acknowledges the receipt of route information. This packet has a similar format to the database description packet and includes a list of LSA headers. Figure 6.37 shows the format of a Link-state acknowledgement packet.
181
FIGURE 6.37
Version
Type = 5 Router ID Area ID Checksum Authentication
Packet Length
OSPF LSA packet verifies the database information that it received.
AuType
OSPF Packet Header
A Link State Advertisement Header
IGRP
The Distance-vector routing protocol IGRP enables gateways to build their routing tables by exchanging information with adjacent gateways (that is, neighbors). The routing information contains a summary about the rest of the network, which helps IGRP make decisions about the best path choice. Unlike RIP, which bases its path choice on hops only, IGRP (despite being considered a Distance-vector protocol) can use a combination of metrics when making route decisions. With IGRP, you can adjust several values to meet the specific needs of your network: DelayMeasures the speed of the link, in units of 10 microseconds BandwidthReflects the data transfer rate across the link, from 1200bps to 10Gbps ReliabilityRepresents fractions of 255 (that is, 255 = 100%) LoadRepresents the saturation of the link, in a fraction of 255 (that is, 0 equals no load, 255 equals a fully loaded link) Hop countCan be up to 255 Table 6.8 describes the function of each of the cost metrics.
TABLE 6.8 Metric Delay Time
IGRP Metric Components

Function Represents the amount of time it takes a signal to propagate end to end. Additional delay occurs with a loaded network; however, the channel occupancy figure accounts for load. Represents the bandwidth, in Kbps, of the slowest link in the path.
Bandwidth
182
TCP/IP PRIMER PLUS
TABLE 6.8 Metric Load Reliability
Continued
Function Calculates a channel occupancy over time to indicate how much bandwidth is currently in use. Displays the current error rate. Measures the percentage of packets that arrive at the destination undamaged.
Because IGRP can use a variety of metrics when making route decisions, it provides a variety of features: It supports larger networks than RIP because it can specify a maximum hop count of 255. It can perform load balancing for traffic when parallel routes exist. It supports complex metrics. Because IGRP considers a variety of metric components, it calculates a single composite metric for the path. The composite metric combines the weighted values of the various metric components into a single number, which represents the best cost. IGRP then selects the best route, based on the smallest composite metric, or cost. Although IGRP keeps track of two additional pieces of informationthe hop count and MTU (that is, the maximum packet size that can travel along the entire path without fragmentation)it does not use this information in the cost calculation. Although IGRP can combine and pass on several cost values, by default it uses only the bandwidth and delay values. If you want to affect path selection, you can change either of these values. The bandwidth value has a higher priority, and routers refer to bandwidth when calculating routing algorithms. However, this value has no effect on the amount of data a particular link can support. On the other hand, it does directly affect path selection, so you need to make sure that you accurately define a bandwidth value to reflect actual data rates across a link. If a value is incorrect, routers might select bad paths for forwarding based on that incorrect value.
IGRP Networks
An IGRP network defines a single routing domain that is identified by an autonomous system number. Generally, a single company manages and controls each autonomous system, and each autonomous system is considered separate from the others. When you have routers configured with IGRP, all routers share the same autonomous system number (which is assigned by an administrator) to exchange route information. In this usage, the term autonomous system describes the IGRP routing domain and all routers within this domain. Although a company may run other IGP routing protocols within its autonomous system, this autonomous system number defines only the IGRP routing domain within the larger autonomous system.
183
For example, if a large enterprise network spanned multiple continents with many routers and links, you would break up this network into multiple autonomous systems. These autonomous system segments would route update traffic based on clear domains. Routers in the same domain share the same network information and adjust to changes within their domain as they occur. However, route changes in other domains would not affect these routers. Defining boundaries reduces the amount of update traffic within a domain, making more efficient use of network bandwidth by keeping intradomain updates off critical backbone segments and slower WAN links. It also makes remote failures transparent to other domains. For example, if a route fails in Japan, the failure would not affect routers in San Francisco.
Network Stability
IGRP uses many techniques to ensure stability in the network. Similar to RIP, IGRP uses periodic broadcasts and triggered updates on nonbroadcast networks, holddowns, split horizon, poison reverse, and an infinity value of 256 to prevent routing loops. Considered a classful routing protocol, IGRP does not support subnetting. In addition, IGRP uses multipath routing to provide network stability. Multipath routing provides additional flexibility because it enables you to split traffic across redundant links with similar or almost similar metrics, which provides load balancing. Multipath routing also contains an automatic switchover to a second link if one link goes down.
IGRP Timers
IGRP includes several control timers that dictate IGRPs general operation (see Table 6.9). These timers control route propagation and expiration. Although the timers have default settings, you can set different time constants.
TABLE 6.9 Timer Update Invalid
IGRP Timers
Function/Default Setting Defines interval between route updates. The default is every 90 seconds. Specifies how long a router should wait in the absence of a routing update message before declaring that route invalid. The default is every 270 seconds (three times the Update timer). Specifies the holddown period for an unreachable destination. The router does not accept updates for the same destination during the holddown period. The default is every 280 seconds (three times the Update timer plus 10 seconds). Indicates how much time should pass before a failed route is removed from the routing table. The default is every 630 seconds (seven times the Update timer).
Holddown
Flush
184
TCP/IP PRIMER PLUS
Load Balancing and Load Sharing

IGRP can send traffic across redundant paths, splitting the traffic stream across equal- or nonequal-cost links, referred to as load balancing. This enables you to maximize the use of the bandwidth to a destination site. If you do not configure unequal-cost load balancing, IGRP balances traffic across equal-cost paths only. However, IGRP does not support VLSM.
EIGRP
Ciscos proprietary routing protocol Enhanced Interior Gateway Routing Protocol (EIGRP) combines the advantages of Link-state routing protocols with the advantages of Distancevector protocols. Because EIGRP combines the advantages of both protocols, it is considered a balanced hybrid protocol. The following are some of the characteristics of EIGRP: It provides faster convergence because it sends partial updates immediately. It supports VLSMs and includes subnet masks in updates. It supports multiple protocols, including IP, IPX, and AppleTalk. It keeps backup paths in routing tables. It supports IP ToS. It uses cost-based metrics, similar to IGRP. It maintains backup paths when multiple routes exist. It is both multicast and unicast.
EIGRP Operation
After an EIGRP router goes through its initial startup, it receives and copies routing tables from its neighbors. When the router detects changes, it sends only partial updates to neighbor routers. This decreases bandwidth use, which results in better efficiency and performance. EIGRP offers a single-routing-protocol solution by supporting multiprotocol networks. This gives companies an advantage if they use multiple protocols, such as IPX, IP, and AppleTalk. Otherwise they would need a separate routing protocol for each, which means a greatly increased amount of update traffic to learn and maintain routes. The only disadvantage to EIGRP is that it requires you to use only Cisco routers, unless the third-party vendors router supports it. EIGRP keeps a highly detailed topology map (that is, the topology database) and uses the Diffusing Update Algorithm (DUAL) to calculate changes and avoid routing loops. It prevents routing loops by referring to copies of neighboring routing tables and using the detailed topology map.
185
Because of the absence of routing loops and the use of triggered updates, EIGRP networks converge very quickly. In addition, EIGRP transmits the subnet mask for each route entry, enabling it to support VLSMs, which makes it a classless routing protocol. EIGRP defines its routing domain (which includes all EIGRP-enabled routers and the networks within the domain) with an autonomous system number, similar to IGRP. Only EIGRP routers that share the same autonomous system number can exchange information because they are considered part of the same domain. EIGRP autonomous systems that have different autonomous system numbers cannot exchange information. An administrator arbitrarily assigns the autonomous system number by enabling and configuring EIGRP on the first router within the domain. After the autonomous system number is assigned, all other routers within the autonomous system must share the same value. EIGRP routers within the same autonomous system must first discover their neighbor routers (that is, routers directly connected to the same local segment or WAN link). By identifying their neighbors, routers can detect unavailable neighbor routers, thereby detecting failures in the network. This allows them to quickly respond to failures and adjust their path selection. The exchange of Hello packets controls the process of discovery. Neighbor routers discover all other local routers by building and maintaining a neighbor, or adjacency, table that lists all routers it has learned about. After routers build neighbor tables, they can begin to exchange route information with their neighbors. Although EIGRP is not connection oriented, it does attempt to guarantee the delivery and receipt of update information by using sequencing information within the EIGRP header portion of the datagram. Receivers must acknowledge the receipt of route information. If the receiver sends no acknowledgement, the sender retransmits the route update. The sending device keeps track of the revision or sequence numbers previously sent, to ensure that all acknowledged updates are accounted for.
Successor and Feasible Routes

EIGRP can maintain multiple routes within the routing table for a single destination. The best route (that is, the route with the lowest-cost path, based on bandwidth and delay by default) is referred to as the successor, and the second (or backup) route is referred to as the feasible successor. EIGRP routers learn successor and feasible successor routes by running DUAL against the topology map that is built based on the neighbor discovery process. EIGRP routers first discover their neighbors, and then they exchange update information to build their topology map. After they have a map of the network, they run the DUAL algorithm against all routes to destinations identified within the map in order to build the local routing table, which lists the following information: Successor and feasible successor routes The local interface The next-hop router address for forwarding traffic to the destination By keeping a backup path in the routing table, EIGRP routers can quickly promote the feasible
186
TCP/IP PRIMER PLUS
successor to successor when the successor becomes unavailable. This allows the router to continue routing traffic to that destination. Meanwhile, the router can actively query its neighbors for a new feasible successor to use. This allows EIGRP routers to quickly detect and adjust around failed paths. EIGRP keeps a separate copy of each of the previously mentioned tables for each major protocol suite for which it performs routingsuch as IP, IPX, and AppleTalkby running separate routing processes for each routing protocol. So if you have all three of these protocols on your network (see Figure 6.38), EIGRP routers have three separate adjacency and topology maps in addition to routing tables. In this case, the router has nine databasesthree for each protocolin addition to the neighbor database, the topology database, and the routing table. A lot of resources and overhead are required to maintain these additional maps and tables. Normally, three different routing protocolsIPX, RIP, and AppleTalks RTMPwould need to be run on each of the routers within the internetwork with each routing protocol separately keeping track of route protocol information. This adds substantial broadcast and multicast traffic for each routing protocol implemented.
FIGURE 6.38 EIGRP Tables
All EIGRP routers within the same autonomous system must maintain three separate databases for each protocol family for which they route.
AppleTalk Neighbors Next Hop Interface Router IPX Neighbors Next Hop Interface IP Router Neighbors Next Hop Interface Router Topology - AppleTalk Copy of every directly connected neighbors route table Each router keeps table of neighbors for each protocol
Topology Table - IPX
Topology Table - IPX Path 1 Backup Path Successor Feasible
AppleTalk Route Table
IPX Route Table
IP Route Table Path 1 Successor
Each router maintains its own route table
187
EIGRP Packet Types

EIGRP exchanges five different packets so that routers can communicate with other routers about the state of their autonomous systems. EIGRP uses the following five packet types: Hello/ACKsSent as multicast advertisements, IGRP routers use Hello packets to build the adjacency table. Some Hello messages do not contain data, known as an acknowledgements (ACKs), and are always sent as unicast datagrams. UpdatesRouters send update packets to exchange route information. They use the information gained in this exchange to build a topology map of the internetwork. Updates always include sequencing numbers. Router sends update packets as either multicast or unicast datagrams. QueriesRouters send query packets to all neighbors when they have no successor or feasible successor route available or when they need to choose a new one. Routers send query packets as a multicast or unicast datagram, depending on whether the query goes to all neighbors (multicast) or to a specific neighbor (unicast). RepliesRouters send reply packets in response to a previous query from a neighbor. Routers always send replies as unicast datagrams. RequestsA router may send a request packet to all neighbors when it first comes online, requesting a complete list of all destinations in order to build its routing table. Or it might send a request for specific information to a particular neighbor. Depending on the request type, a router can send this message as a multicast or unicast datagram.
BGP
The protocols described thus far in this chapter (that is, IGPs) use frequent updates and routing methods for propagating traffic, which makes them incapable of handling a very large environment. In addition, a company generally uses IGPs within a single autonomous system or company internetwork. The explosion of the Internet created a need for BGP, an EGP that provides loop-free interdomain routing and is a robust, stringent, rules-based routing protocol. RFC 1771 defines BGP version 4 (BGPv4), the current version of BGP, as an inter-autonomous system routing protocol. The Internet uses BGP as its primary protocol, to support the transit of traffic across the great superhighway. The enhancements to version 4VLSM and Classless Interdomain Routing (CIDR; that is, supernetting)have allowed BGPv4 to handle the exponential growth of the Internet. Most companies connecting to the Internet do not need or use BGP. If an organization has only one gateway (that is, a single exit point) connecting the internetwork to the outside world, it can usually put in a default route. This allows all traffic destined to unknown networks to be forwarded through the default path, serviced by the upstream providers gateways, and the upstream provider participates in the BGP network. Implementing a default route means there is no routing update traffic overhead or resources necessary on the gateway to store and maintain all routes within the Internet.
188
TCP/IP PRIMER PLUS
BGP should be implemented in the following situations: If you have multiple exit points connecting to a single ISP (for load sharing) If you have multiple paths to different ISPs and would like to dictate how traffic is forwarded across these links If your routing policy or methods are different or go beyond the simplistic use of a default route (that is, you need intelligent path selection and specific criteria) If your networks infrastructure is used as a transit area for other organizations traffic
IGPs Versus EGPs

BGP routers learn and maintain information about all destination networks within the Internet and about the path through the autonomous systems to get to these networks. When traffic reaches the ultimate destination network, IGP protocols (that is, RIP, IGRP, EIGRP, and OSPF) take care of the local route forwarding within the autonomous system. As an EGP, BGP connects independent autonomous systems together. Autonomous system numbers, which are assigned by ARIN, define BGP routing domains. The autonomous system number assigned to an organization represents a major hop (that is, transit area) within the Internet. Each autonomous system may have many IGPs running within it, but the number and types of these dynamic protocols is irrelevant and transparent to BGP. Although you can use BGP as an IGP, you use BGP almost exclusively as an EGP. The Internet today consists of many transit areas. Different organizations control these transit areas, with no one organization governing the lot of them. The Internets vastness and lack of governing created a need for a robust, stringent rules-based routing protocol such as BGP. Currently, more than 105,000 routes exist on the Internet. Each BGP router within the Internet must learn and maintain path information and perform intelligent path selection to facilitate the forwarding of datagrams throughout the Internet, not to mention the resources (such as memory and CPU time) necessary to maintain this information. With so many routes, transit areas, and multiple paths throughout this internetworking maze, BGP has to have the ability to detect and correct problems (for example, downed networks, routing loops).
Sources for Current Internet Routing Table Numbers

You can use the following sources to find information on the current Internet routing tables today: http://antc.uoregon.edu/route-views/dynamics http://www.mcvax.org/~jhma/routing/bgp-hist.html http: //www.apnic.net/stats/bgp/TOTAL/totalann.html
Because BGP has to have the ability to detect and correct network problems, it can eliminate routing loops. You can implement BGP version 4 in one of two ways:
189
Full meshA full-mesh topology requires separate logical TCP connections between all BGP routers within the same autonomous system, allowing gateways to quickly determine whether a loop exists and prune it. Partial meshA partial mesh topology does not require all routers to maintain logical connections with one another. This reduces the number of TCP connections, but it opens up the possibility of routing loops. To aid in reliability, BGP has one characteristic unlike any other routing protocol: It uses TCP to provide connection-oriented, reliable transport of its update traffic. All IGP protocols are connectionlessthat is, they do not require a logical connection to pass information to other gateways. IGP protocols typically send updates as either broadcasts or multicasts, although a few send them as unicasts. Whatever the method, they do this over connectionless protocols, such as IP and UDP. BGP guarantees reliable delivery of data, running on top of a logical TCP session, which sequences and acknowledges each exchange between BGP peers. BGP uses TCP port 179. Unlike previous versions of BGP, BGPv4 supports classless routing by including subnet masks within routing updates when describing destinations (referred to as network reachability information). Also, unlike earlier versions of BGP, BGPv4 supports route summarization (that is, the aggregation of multiple IP addresses into a single route advertisement).
BGP Routers
Routers placed in different areas of a BGP network have different names. In a BGP network four different types of routers exist: BGP speaker routersThese are BGP routers. Peer or neighbor routersThese are routers that connect to a common segment. Internal peer routersThese routers are peers within the same autonomous system. External peer routersThese routers are BGP neighbors from different autonomous systems. For example, if Autonomous System 100 consists of three gateways in a full-mesh topology, each of these routers would have a TCP connection with each other and would form an internal BGP (IBGP) relationship with its neighbors in the same autonomous system. The gateway connecting Autonomous System 100 to another autonomous systemfor example, Autonomous System 200would form an external BGP (EBGP) relationship with the gateway from the other autonomous system. The type of relationship a neighbor has with its peer internal or externaldefines the rules for exchange (see Figure 6.39). All BGP routers have some type of peer relationships with other routers. The type of peer relationship depends on whether the routers reside within the same autonomous system. Two routers connecting different autonomous systems are external peers, and routers within the same autonomous system are internal peers. Routers that belong to the same autonomous system are called IBGPs. IBGP neighbors cannot advertise route information beyond their local peers, or neighbors.
190
TCP/IP PRIMER PLUS
FIGURE 6.39
Multiple BGP Connections to One ISP
Rules for exchange vary, depending on what type of relationship a router has with its peer.
EBGP
EBGP AS 200
IBGP Peers AS 100 EBGP EBGP
Routers that belong to different autonomous systems are called EBGPs. EBGP neighbors may propagate route information learned to all other neighbors on all other interfaces.
BGP Operation
When you enable BGP on a gateway, you assign it an autonomous system number based on the autonomous system to which it belongs. In addition, you configure the BGP speaker with the addresses of all its peers. When this speaker comes online, it must establish TCP connections with all its peers (both internal and external) in order to facilitate the exchange of BGP information. When BGP peer routers establish a TCP session, peers may exchange the BGP reachability information that builds their routing tables. BGP uses this information to create a loop-free map of the autonomous systems. After the initial exchange of the entire table, peers exchange changes only. TCP tracks all exchanges by sequencing and acknowledging. TCP uses keepalives to maintain connections between BGP peers when these peers do not actively exchange data. BGP generates a notification message when it encounters an error, causing the TCP session to terminate between peers. If the TCP session fails, BGP fails. BGP routers do not store routing information within the same routing table as they store IGP learned routes. BGP routers, depending on the vendor implementation, may maintain up to three additional routing tables or combine them into one. However, no matter the number of tables they maintain, each BGP speaker needs to distinguish the following: Route information received (that is, updates) Route information to be advertised The local BGP routing table BGP speakers advise peers of changes to destination routes through the exchange of updates. If a route becomes unavailable, a speaker advertises within the update sent to its neighbors that it plans to withdraw a route from service, so its neighbors should remove the route from their table. If the BGP speaker has a better path available to a destination, it advertises the new path and its attributes. Receivers then replace the old route with the new one.
191
Unlike all IGPs, BGP does not use metrics, such as hop, delay, bandwidth, reliability, load, or MTU, in its path selection. Rather, BGP uses path attributes in a hierarchical fashion to facilitate best path selection to a destination. (We will discuss BGP attributes in detail later in this chapter.)
The BGP Header and Fields

All BGP datagrams begin with a common 19-byte header. Figure 6.40 shows the format of a common BGP header.
Marker
The marker field is up to 16 bytes in length. This field identifies the beginning of an open request between peers and BGP authentication implementation.
FIGURE 6.40
All BGP datagrams have the same header.
Marker
Length
Type = 1
OPEN, UPDATE, NOTIFICATION or KEEPALIVE Message
Length
The 2-byte length field identifies the length, in bytes, of the BGP datagram plus the header.
Type
The 1-byte type field identifies the type of BGP message that a router sent. BGP routers can send four different types of messages: Open Update Notification Keepalive The type of message that appears in this field affects the rest of the BGP header. The types of message formats are described in the following sections.
Open Messages
BBP routers send an open message immediately after establishing the TCP port 179 peer connection. This first BGP message initiates a BGP peer relationship between internal or external peers. Figure 6.41 shows the BGP open message format.
192
TCP/IP PRIMER PLUS
FIGURE 6.41
The BGP open message includes six fields: Version, My Autonomous System, Hold Time, BGP Identifier, Optional Parameters Length, and Optional Parameters.
BGP-4 Message Header Length My Autonomous System
Marker
Type = 1 Hold Time BGP Identifier
Version
Opt Parm Len
Optional Parameters
The Open message adds six fields to the BGP header. Table 6.10 describes them.
TABLE 6.10 Field Version
BGP Open Message Fields

Bits 8 16 16 32 8 Description Displays the version of BGP (currently version 4). Displays the autonomous system number of the sender. Controls the timer between keepalives and update messages. Uniquely identifies the BGP speaker (that is, sender). Identifies the length of any optional parameters that might exist, such as authentication information. If no parameters exist, this field contains a zero. If parameters are present, this value identifies the size in bytes of the expected optional parameter field that follows. Lists the implemented optional parameters, such as authentication.
My Autonomous System Hold Time BGP Identifier Optional Parameters Length
Optional parameters
Variable
Update Messages
Update messages (Type 1) contain network reachability information. Peers exchange updates with peers to learn and maintain routes. Figure 6.42 shows the BGP Update message format. The Update message (Type 2) adds five fields to the BGP header. Table 6.11 describes them.
193
TABLE 6.11 Field
BGP Update Message Fields

Bits 16 Description Specifies withdrawn routes. If no routes are being withdrawn, this value is zero. If routes are being withdrawn from service, this indicates the size, in bytes, of the withdrawn routes field. Lists all routes withdrawn from service. Identifies the total length, in bytes, of the Path Attributes field, included within this message. Defines the advertised attributes. This field contains two main categories of attributes: well known and optional. Path attributes are discussed later in this chapter. Lists all destinations that the router advertises.
Unfeasible Routes Length
Withdrawn Routes Total Path Attribute Length
Variable 16
Path Attributes
Variable
Network Layer Reachability Information
Variable
FIGURE 6.42
BGP Update messages have five additional fields: Unfeasible Routes Length, Withdrawn Routes, Total Path Attributes, Path Attributes, and Network Layer Reachability Information.
BGP-4 Message Header Length Routes Length
Marker
Type = 2
Unfeasible
Withdrawn Routes (variable length) Path Attribute (variable length)
Total Path Attribute Length
Network Layer Reachability Information (variable length)
Notification Messages
Notification messages (Type 3) occur when BGP routers encounter an error. When a router sends a notification, BGP fails and the peers tear down the TCP connection they had established. Figure 6.43 shows the notification message format. The Notification message adds three fields to the BGP header. Table 6.12 describes them.
194
TCP/IP PRIMER PLUS
FIGURE 6.43
The BGP Notification message has an additional three fields: Error Code, Error Subcode, and Data.
BGP-4 Message Header Length Error Subcode
Marker
Type = 3 Data (variable length)
Error Code
TABLE 6.12 Fields Error Code Error Subcode Data
BGP Notification Message Fields

Bits 8 8 Variable Description Displays the type(s) of error(s) that have occurred. Gives more specific information about the type of error that occurred. Diagnoses the reason for the notification. This value is dependent on the contents of the other two fields (Error Code and Error Subcode). See RFC 1771 for specific values.
Keepalive Messages
In response to the initial Open message, Keepalive messages confirm the establishment of the peer connection, whether it is internal or external. After the routers establish peer relationships, neighbors continue to exchange keepalives to maintain the connection to determine reachability between peers. Figure 6.44 shows the keepalive message format.
FIGURE 6.44
Keepalive messages consist of the BGP message header only, without any additional information. This allows the BGP connection to remain open between peers.
BGP-4 Message Header Length = 19 octets
Marker
Type = 4
Path Attributes
Routers use path attributes to describe a destination routes reachability and to determine the best path. BGP speakers parse these attributes in order, giving a higher precedence to attributes in ascending order. You can adjust these parameters (that is, path attributes), which gives BGP its flexibility. BGP path attributes have four categories, as described in Table 6.13.
195
TABLE 6.13 Category
Path Attribute Categories

Description All vendor implementation must recognize well-known attributes, and they are included in all updates. The BGP speaker must fully process these attributes. These attributes may or may not be present in an update. If they are present, all vendor implementation must recognize them, and BGP speakers must fully process them. If a BGP speaker receives this attribute, it passes it. The receiver does not have to recognize an optional attribute. The receiver does not have to recognize or process this optional attribute. A BGP speaker does not pass this attribute to its neighbors.
Well-known mandatory
Well-known discretionary
Optional transitive Optional nontransitive
BGP update messages advertise path attributes within BGP update messages identified by type codes. Table 6.14 shows the path attributes defined within RFC 1771.
TABLE 6.14 Type Code 1Origin
BGP Path Attributes

Attribute Well-known mandatory Description Identifies the origin of the route (that is, how the route was learned and placed into the routing table by the reporting router). The following origin types exist: IGPLearned via network reachability, which is internal to the originating routers autonomous system EGPLearned via EGP IncompleteLearned from an unknown source Lists the autonomous systems that describe the path to this destination. For example, a destination such as 192.15.2.0 may have an autonomous system path of 100 to 300 to 800, which means it takes three autonomous system hops to get to this network. When autonomous system routers (that is,
2AS_path
196
TCP/IP PRIMER PLUS
TABLE 6.14 Type Code
Continued
Attribute Description EBGP peers) pass route information between autonomous system routers, the router forwarding the update to the new autonomous system adds its autonomous system to the path. This allows BGP speakers to identify the autonomous system path that the route has traversed through the Internet.
3Next_Hop
Identifies the IP address of the nexthop router or border gateway used to reach the destination. Allows an autonomous systems routers to influence the routing decisions of another autonomous systems routers. When multiple exit points exist, connecting two autonomous systems together, routers from one of the autonomous systems may advertise different Multi-Exit-Disc (MED) values to the external neighbor router in the other autonomous system. The lower the MED value, the better the path. By advertising one path with a lower MED value, routers will prefer one of the paths over the other. This is the only attribute that provides this function. Only routers within a single autonomous system use this, and it is not propagated to other autonomous systems. When multiple paths exist to route traffic outside this autonomous system, routers within an autonomous system may set the local preference value higher for one path, indicating the preferred route. Internal routers then
4Multi-Exit-Disc (see Figure 6.45)
Optional nontransitive
5Local Pref (see Figure 6.46)
197
TABLE 6.14 Type Code
Continued
Attribute Description forward traffic based on this information, choosing the path with the highest preference.
6Atomic_Aggregate
This value is set only after route summarization configuration. When a system administrator configures route summarization, the router where the summarization originated sets this attribute. It is included in advertisements, advising other BGP routers that the advertised route represents a less specific summary of other routes that are not identified within the update. This value is set only when the atomic aggregate is set. Identifies the autonomous system and router where route summarization originated.
7Aggregator
Optional transitive
FIGURE 6.45
MED-Multi Exit Descriptor

AS 100
The MED attribute influences routing decisions between autonomous systems. For example, if an ISP maintains multiple connecting paths between itself and a downstream autonomous system, the ISP may configure its routers with different MED values to influence the path the downstream router uses to send traffic.
MED 100
MED 100
Best Route
AS 200
198
TCP/IP PRIMER PLUS
BGPv3 Versus BGPv4

BGPv3 (RFC 1267) and BGPv4 cannot work together. However, you can configure routers to support BGPv3 or BGPv4 on a per-interface basis to operate in a mixed environment. Table 6.15 is a quick reference to the difference between BGPv3 and BGPv4.
FIGURE 6.46 Local Preference
AS 100 AS 200
The Local Preference attribute propagates only within an autonomous system and designates a preferred path to a destination when multiple paths exist. In this case, autonomous system 300 has multiple outbound paths connecting through autonomous system 100 and autonomous system 200. The router chooses the path with the highest local preference as its outbound path. In this case, it chooses the leftmost router with a local preference of 200.
TABLE 6.15 Characteristic Supports VLSM (that is, classless routing). Includes subnet masks within updates. Supports summarization. Full or partial mesh. Supports Local Preference, Atomic_Aggregate, and Aggregator attributes.
Preferred Route
LP=200 LP=100
AS 300
BGPv3 and BGPv4

BGPv3 No BGPv4 Yes
No Full mesh No
Yes Both Yes
199
Summary
Routing protocols allow routers to dynamically learn paths to destinations and to adjust to changes in network topology. Whether you use BGP or RIP, the purpose for every protocol is the same: to forward datagrams to their destination. RIP is a Distance-vector protocol. Like all other Distance-vector protocols, it uses the metric distance (measured in hops) to determine best path selection. RIP is broadcast based, it is an IGP, it works best on small-sized networks, and it uses a Distance-vector algorithm. Two versions of RIP exist: RIPv1 and RIPv2. OSPF uses a Link-state algorithm and makes more intelligent decisions regarding path selection than RIP. OSPF like all other Link-state routing protocols, considers any or all of the fol, lowing metrics: link capacity (bandwidth), delay, reliability, load, and MTU. OSPF provides several advantages over Distance-vector protocols; however, RIP still remains the most popular protocol in use today, primarily because of its simplicity. The Distance-vector protocol IGRP allows gateways to build their routing table by exchanging information with adjacent gateways (that is, neighbors), similar to OSPF Unlike RIP, which is . also a Distance-vector protocol, IGRP uses a variety of metrics to determine best path selection. This is called a composite metric. IGRP considers the metrics bandwidth, delay, reliability, and load, which allows it to provide support to large networks, and handle load balancing. Considered a hybrid protocol, EIGRP combines the advantages of Link-state routing protocols and Distance-vector protocols. RIP, OSPF IGRP, and EIGRP are all IGPs. , With the explosion of the Internet, the public needed a robust, stringent, rules-based protocol that had enough flexibility to handle the ever-changing Internet. BGP proved to be the answer. BGP, which is an EGP, bases path selection on path attributes. The enhancements to BGPv4 support for VLSMs, route aggregation, and CIDRhave enabled it to become the primary protocol for the Internet. To keep track of the various protocols and their specific characteristics, Table 6.16 is a summarizes the routing protocols discussed in this chapter.
TABLE 16.16 Characteristic Classification Number of hops
Routing Protocols Summary

RIPv1 Distancevector 15 30 RIPv2 Distancevector 15 30 OSPF Link-state N/A Triggered IGRP Distancevector 100255 90 EIGRP Hybrid N/A Triggered BGP Pathvector N/A N/A
Number of seconds between periodic updates Broadcast
Yes
Yes
Multicast
Yes
Multicast
No
200
TCP/IP PRIMER PLUS
TABLE 16.16 Characteristic Entire table sent VLSM Primary metric ToS/QoS
Continued
RIPv1 Yes Classful Hops No UDP RIPv2 Yes Classless Hops No UDP OSPF Only changes Classless Bandwidth Yes UDP IGRP Yes Classful Bandwidth and delay Yes UDP EIGRP Only changes Classless Bandwidth and delay Yes UDP BGP Only changes Classless Path attribute Yes TCP
Type of connection
Review Questions
1. What kind of routing protocol is RIP considered to be? 2. Name some of RIPs characteristics. 3. What metric does RIP uses to determine best path selection? 4. How often does RIP send its broadcasts, and what does it send in these broadcasts? 5. How many entries can RIP send in its broadcasts? 6. With RIPv1, how many hops can a datagram traverse if the destination is considered unreachable? 7. What three features does RIPv2 support that RIPv1 does not? 8. Why is RIPv2 virtually obsolete? 9. What are some of the disadvantages of RIPv1? 10. What various mechanisms does RIP use to avoid routing loops? 11. What timers does RIP use? 12. What kind of routing protocol is OSPF is considered to be? 13. What metrics does OSPF consider when making routing decisions? 14. What advantages does OSPF have over RIP? 15. What are some of the characteristics of OSPF? 16. What three databases do OSPF routers maintain and build? 17. What is an OSPF adjacency database? 18. What is an OSPF Link-state database?
201
19. What is an OSPF forwarding database? 20. What is an OSPF LSA? 21. What is the difference between an OSPF inter-area advertisement and an intra-area advertisement? 22. What are the six OSPF router states? 23. What are the four OSPF router types? 24. What is the OSPF backbone area type? 25. What are the five OSPF packet types? 26. What is the function of an OSPF Hello packet? 27. What is the function of an OSPF Database Description packet? 28. What different metrics does IGRP use to make routing decisions? 29. What is the maximum hop count for IGRP? Why is it significant that IGRP has a larger hop count than RIP? 30. What are the various IGRP timers and what are their functions? 31. What are some of the characteristics of EIGRP? 32. What type of protocol is EIGRP? 33. What are some of the advantages and disadvantages of the fact that EIGRP offers multiprotocol support? 34. What is the difference between EIGRP successor and feasible successor routes? 35. What are the five different EIGRP packet types? Briefly describe each. 36. What is the difference between IGPs and EGPs? 37. What enhancements to BGPv4 allowed it to become the primary protocol used by the Internet? 38. In what situations would you want to implement BGP? 39. What is the difference between a BGP partial-mesh and a BGP full-mesh topology? 40. What are the four types of BGP routers? 41. Each BGP speaker, no matter what table it maintains, needs to distinguish what things? 42. On top of what protocol does BGP run? 43. What are the four different BGP message types? 44. When is a BGP Open message sent, and what is its function? 45. What is a BGP Notification message used for?
202
TCP/IP PRIMER PLUS
46. What metric does BGP use to determine the best path to a destination? 47. Into what four categories do BGP path attributes fall? 48. In BGP, what is meant by local preference? 49. What are some of the differences between BGPv3 and BGPv4?
CHAPTER 7
TRANSPORT/HOST-TO-HOST LAYER

Connection-oriented Protocols Connectionless Protocols
Transport Layer Protocols

Communication systems do not use a single protocol to handle all transmission tasks; most transmission tasks require a series of protocols that work together within a protocol suite. The Transport layer or Host-to-Host layer provides a reliable flow of data between two processes running on remote hosts. The protocols that reside on this layer take messages (data streams) from upper-layer applications and processes and convert them into segments to be sent down to the Network or Internet layer for packaging as datagrams. We will discuss the two Transport or Host-to-Host layer protocols, known as UDP (User Datagram Protocol) and TCP (Transmission Control Protocol), within the TCP/IP protocol suite, in Chapters 8, Transmission Control Protocol (TCP), and 9, User Datagram Protocol (UDP). We limit our discussion in this chapter to the function and services provided by the Transport or Host-to-Host protocols. The type of service provided depends on the Transport layer chosen. UDP (connectionless) provides fast, unreliable delivery of segments between remote processes. TCP, which is connection-oriented, provides the sequencing of data to ensure reliable delivery from two hosts. All protocols fall into one of two categories: connectionless and connection-oriented. Vendors can choose whether upper-layer applications utilize UDP or TCP. If vendors want speed, they choose UDP, as it offers fast, best effort delivery of datagrams. If speed is less important than reliability, they implement TCP, as it offers slower, guaranteed delivery. Simply put, the choice comes down to speed versus reliability. Figure 7.1 shows how the TCP/IP protocol suite maps to the DoD (Department of Defense) and OSI Reference Model. UDP offers fast, unreliable delivery of messages between applications running on remote hosts. Considered a simple protocol, UDP provides this fast service by merely sending packets from one host to the other, relying on upper-layer or application protocols to provide reliability. However, UDP has a major drawback: It offers no guarantee that the datagrams it sends actually arrive at the other end.
204
TCP/IP PRIMER PLUS
FIGURE 7.1
DOD
OSI
Application
Notice that TCP and UDP map to the Transport layer of the OSI model and to the Host-to-Host layer of the DoD model.
Presentation Session
Host to Host
TCP or UDP
Transport
Internet
Network
Network Access
Data Link Physical
TCP offers slower but guaranteed delivery of data. It provides this service by controlling the flow and size of the datagrams being sent so the Network or Internet layer can handle the transmission. It then goes through a series of acknowledgements and sequencing to guarantee each segment reaches the destination. Because of all the checks and balances that TCP goes through during delivery, it can provide a reliable but slower flow of data, which means the application layer does not have to concern itself with guaranteeing delivery, as with UDP. The Transport layer or Host-to-Host layer provides the following services: Controls end-to-end communication between two processes running on different hosts Provides connection-oriented or connectionless services to upper layers Uses client and server port address to identify processes running within a host Segments data for upper-layer applications
Connection-Oriented Protocols
TCP is the only connection-oriented protocol that resides within TCP/IP suite at the Transport layer. Vendors decide what applications will utilize TCP as its Transport layer protocol depending on whether they require its features. Whether connection-oriented protocols reside on the Transport layer or another layer, they always exhibit the same six characteristics: Session setupEstablishes a virtual circuit between two communicating processes running on end systems (see Figure 7.2). AcknowledgementsNotifies the sending device that it has received the data. SequencingKeeps track of the order of datagrams.
Chapter 7 TRANSPORT/HOST-TO-HOST LAYER
205
Flow controlControls the speed of incoming data. Hosts can tell other hosts to speed up or slow down the transmission of data. KeepalivesMaintains a connection during times when no data transmission occurs. Session teardownOccurs when either end system requests to terminate the virtual connection (see Figure 7.3). A connection-oriented session setup always starts from the lower layers and goes to the upper layers of the OSI model. TCP is the primary connection-oriented protocol within the TCP/IP suite. This means whenever an application runs over TCP, TCP sets up the virtual connection before any meaningful data transmission occurs. Once the lower layers have established a session with the upper layers, data transfer can occur over this connection between communication applications. TCP uses a three-frame exchange to set up the session. We will discuss this in more detail in Chapter 8.
FIGURE 7.2 Session Setup
Client TCP port Server TCP port
Any application that utilizes TCP as its Transport protocol must establish a connection before it can transmit data.
A
B 100.0.0.2 110.0.0.10
1st 3rd
TCP Syn TCP Syn/Ack TCP Ack 2nd
FIGURE 7.3
Session Teardown
User exits Client TCP port Server TCP port
Exiting an application causes a TCP teardown to begin.
A 100.0.0.2 110.0.0.10
1st 3rd
TCP Fin TCP Fin/Ack TCP Ack 2nd
206
TCP/IP PRIMER PLUS
To ensure that a host does not lose data during transmission, connection-oriented protocols exchange sequencing and acknowledgements. The way protocols sequence each frame varies with each protocol. Some sequence frame by frame; some sequence each byte within the frame. Whatever the method, the purpose remains the same: to detect lost data or frames, and if lost, recover them by retransmitting the data. When hosts remain idle (not exchanging data), they still need to maintain the virtual connection by using keepalives. Keepalives are small messages sent between two machines to ensure connectivity. They enable the virtual connection to be maintained while the hosts process remains idle. Keepalives do not carry upper-layer data and hosts send them only to maintain idle connections. Sometimes a host can send too much data at once and overflow a receiving hosts buffers. A receiving host using a connection-oriented protocol can utilize the flow control mechanism to control the flow of data. By using the flow control mechanism, a receiving host can tell a sending host to speed up or slow down the amount of data sent, thus regulating the amount of traffic. Flow control methods vary depending on the protocol used. TCP implements flow control through a sliding window mechanism. The sliding window mechanism enables TCP to dynamically adjust its window size when needed to alert the sending host to slow down transmission or stop altogether. The upper layers tear down the virtual connection when either side sends a request for termination of the session. We will discuss TCPs use of all six characteristics in more detail in Chapter 8.
Connectionless Protocols
Regardless of what layer they reside on, connectionless protocols send data but do not check whether the receiving host actually receives the data or not. Connectionless protocols rely on other protocols to ensure that the sent data gets to the receiver and recovers lost data. These protocols do not have the reliability that their connection-oriented counterparts do, but they provide something that connection-oriented protocols cant offerspeed and minimal overhead. We will discuss the UDP protocol in more detail in Chapter 9.
Connectionless Versus Connection-oriented Protocols

Before implementing a particular protocol vendors ask themselves the age-old networking question: speed or reliability and overhead? Connectionless protocols prove faster and more efficient because they do not have the overhead from sequencing and acknowledging each frame or byte; for example, in a connection-oriented session setup. Additionally, connectionless protocols dont have to maintain idle connections with keepalives, which create more overhead. When vendors want fast delivery, they choose connectionless protocols; when they need reliability more than speed, they choose connection-oriented protocols. For example, if a vendor writes a printing application, he or she typically would use a connection-oriented protocol. Users want to be surenot hopetheir print jobs go through. Table 7.1 compares the two protocols.
207
TABLE 7.1 Protocol
Connection-oriented and Connectionless Protocols

Attribute No session setup No session teardown No acknowledgements No sequencing No flow control No keepalives Best effort of delivery Fast delivery of data Little overhead No recovery or retransmission Session setup Session teardown Acknowledgements Sequencing Flow control Keepalives Reliable, guaranteed delivery Slower delivery of data Tons of overhead Error recovery Retransmission of data
Connectionless
Connection-oriented
Ports and Sockets

The Transport layer, whether using connection-oriented (TCP) or connectionless (UDP) protocols, processes addresses and uses ports, also referred to as sockets to identify the process running on the host. The Transport layer handles source and destination addressing of ports, addresses that identify which upper-layer protocol or process wants to communicate on a particular device. This layer uses client-based and server-based addresses, such as TCP and UDP ports, to identify the process running within a host. As previously mentioned, the Transport layer is responsible for segmenting data handed down by the upper-layer applications. To govern, track, and manage these segments, the Transport layer utilizes port numbers for each application. Remember that a vendor can either implement connectionless or connection-oriented protocols at this layer, which means that depending on the protocol implemented, the data may or may not have guaranteed delivery. This confuses some people because they think the Transport layer provides only guaranteed reliable delivery of data. Just remember that the delivery is not always guaranteed.
208
TCP/IP PRIMER PLUS
For example, if a user wants to open a client Telnet connection with a remote Telnet server, that session opens up a unique port, which is a variable or made-up port. The connection uses this port to reach a Telnet server. Client ports are chosen randomly whereas server ports have an assigned port value, typically known as well-known ports. When you connect to the host or server, you typically connect to a well-known port; in this case Telnet, which uses well-known port 23 (see Figure 7.4). Table 7.2 shows the different port categories.
FIGURE 7.4 Client and Server Ports
Client Port Telnet 23 Server Port
In this case, Telnet always uses TCP port 23.
4001
100.0.0.2
110.0.0.10
Client Range = 1024-65,536 Server Range = 1-1023
TABLE 7.2
Port Categories
Range and Description 0-255 Defines well-known programs used in the industry that have become the official standard for addressing such programs. 256-1023 Reserved ports that vendors can implement on an as-needed basis. 1024-65536 Variable (or ethereal) ports made up on-the-fly each time a client process begins and opens a new port.
Port Category Well-known server ports
Less well-known server ports Client
In Figure 7.4 the client IP address and port 4001, or variable port made up on-the-fly, and the destination hosts IP address and well-known Telnet server port 23 make up what is known as a socket pair. A socket pair is an end-to-end connection between two hosts (source and destination) that uses both (or pairs up) their respective IP addresses and their ports. The client and server ports clearly identify the process communicating on each box. By linking the sending
209
hosts address and port to the destination hosts address and port, TCP or UDP can manage the communication between these hosts and their processes, and distinguish them from other virtual connections to the same hosts.
Note
Remember that the Transport layer deals with sockets or port addresses. Socket pairing describes an end-to-end connection of two hosts, source and destination, which include both their IP addresses and ports.
Within the TCP/IP suite, TCP and UDP ports identify the process or program running within a host. TCP, or the connection-oriented protocol, then maintains the connection-oriented process. Using a connectionless protocol such as UDP, you would simply pass data unreliably, hoping it gets to its destination, and rely on upper-layer protocols to maintain the connection.
Summary
The Transport layer or Host-to-Host layer controls end-to-end communication between two processes running on different hosts and provides connection-oriented or connectionless services to upper layers. It also uses client and server port address to identify processes running within a host and segments data for upper-layer applications. Within in the TCP/IP suite, two vastly different protocols reside on this layer, UDP (connectionless) and TCP (connection-oriented). All protocols fall into two categories: connectionless and connection-oriented. Connection-oriented protocols provide guaranteed reliable delivery of data between two end systems. Connectionless protocols offer fast, unreliable delivery of messages between applications running on remote hosts. Connection-oriented protocols will always exhibit the same six characteristics: session setup, acknowledgements, sequencing, flow control, keepalives, and session teardown. The Transport layer handles addressing with ports and sockets, addresses that identify which upper-layer protocol or process wants to communicate on a particular device. A client port, which is a variable port; a server port, which is an assigned port; and the source and destination IP addresses of two hosts with end-to-end communication make up a socket pair.
Review Questions
1. What four services does the Transport or Host-to-Host layer provide? 2. What do all connection-oriented protocols exhibit?
210
TCP/IP PRIMER PLUS
3. What are well-known ports and what is their range? 4. What are less-known ports and what is their range? 5. What are client ports and what is their range? 6. Describe socket pairing. 7. Compare and contrast the two Transport or Host-to-Host layer protocols that reside in the TCP/IP protocol suite. 8. What is flow control? 9. What choice do vendors have to make when implementing a particular Transport layer protocol? 10. What protocol utilizes acknowledgements and sequencing and what functions do acknowledgements and sequencing have?
CHAPTER 8
TRANSMISSION CONTROL PROTOCOL (TCP)

TCP Header and Fields TCP Operation Connection Setup and Teardown Sequencing and Acknowledgements
Introduction to TCP
Originally, Vinton Cerf and Robert Kahn designed TCP to provide reliable data transmission between remote hosts communicating over a packet-switched network. Before the invention of TCP, data transmission over packet-switched network infrastructures proved somewhat unreliable. The quality of delivery (or lack of reliability), different media types, and the potential for congestion to impede data delivery made it necessary for a connection-oriented protocol to provide end-to-end reliable services to processes and applications communicating between remote hosts. The DoD (Department of Defense) adopted TCP as its primary protocol for reliable delivery of information over the ARPA network. Since its invention, TCP has become a standard protocol for the Internet, providing guaranteed delivery of data between hosts. TCP maps to the Host-to-Host layer within the DoD and Transport layer of the OSI model. Only TCP and UDP function at these layers. Vendors can implement TCP when they need guaranteed delivery of data or use UDP when they require speed more than guaranteed delivery. Figure 8.1 shows how TCP maps to the OSI and DoD reference models.
212
TCP/IP PRIMER PLUS
FIGURE 8.1
DOD
OSI
TCP guarantees the delivery of data at the Host-toHost or Network layer.
Host to Host
TCP or UDP
Transport
Internet
Network Access
TCP Header
Now that you understand the general functions and implementations of connection-oriented TCP lets explore the fields within the TCP header futher. Figure 8.2 gives an example of a TCP header as defined in RFC 793. Figure 8.3 shows a tangible TCP header as it actually appears during implementation. The TCP header specifies the source and destination ports, sequencing and acknowledgement (ACK) values, and TCP flags used by a host to identify how to process the information. A description of each item contained in the TCP header will appear following the figures.
FIGURE 8.2
Source Port Sequence Number Acknowledgement Number Offset Reserved Checksum Options + Padding U A P R S F Window Urgent Pointer Destination Port
This figure shows the format of a TCP header. A TCP header normally contains 20 bytes unless options are being used. Note that a header can contain no options or data.
Data
Chapter 8 TRANSMISSION CONTROL PROTOCOL (TCP)
213
Destination port Acknowledgement number Source port Sequence number
FIGURE 8.3
Note that in this particular TCP header no options are being used and the reserved bits and urgent pointer fields are not present.
Data offset Control flags Window Checksum TCP options
Source Port
The 2-byte source port field identifies the sending hosts communicating process (socket). An example of this is a client port 102465,535 or server port 11023. Because TCP supports bidirectional communication, the value in this field depends on from which direction the communication comes. If the client initiates the request, the port falls within the client range. If a server responds to the client request, the port falls within the server range.
Destination Port
The two-byte destination port identifies the receiving hosts communicating process (socket). The port that appears in this field depends on who is communicating with whom: client to server or server to client.
Note
Remember that each TCP segment has a source and destination port number. These port numbers identify the sending and receiving devices. These two values, along with the source and destination IP addresses in the IP header, make a socket pair. A socket pair indicates the two end points that uniquely identify each TCP connection in an internet.
214
TCP/IP PRIMER PLUS
Sequence Number
TCP uses sequencing to keep track of each byte of data. Every octet of data sent over a TCP connection has a sequence number. An algorithm calculates the initial sequence number, which is included in the synchronization frame during session setup and is contained within the 4-byte sequence number field. This sequence number identifies the first byte within each datagram being sent. Think of the sequence number being expressed as I am now sending data starting with this number. If the receiver does not acknowledge (ACK) the data sent, the sender assumes the data is lost and retransmits it.
Note
Note that TCP does not sequence every byte of data, but guarantees delivery of each byte by sequencing each octet. It merely acknowledges (ACKs) the particular sequence number within each packet being sent. TCP also utilizes windowing to control the transmission of datagrams. We discuss acknowledgements (ACKs) and windowing later in this chapter.
Acknowledgement Number
The 4-byte acknowledgement number field contains the value that identifies the next sequence value the host expects to receive from the other side. The ACK number should equal the other sides previously sent sequence number plus the length value. The receiver implies that it received all the data sent up to that point. This is called an implied acknowledgement. The receiver can acknowledge receipt of multiple frames with a single acknowledgement (ACK). This process operates more efficiently than individually acknowledging each frame and its payload of bytes. Remember that the window size determines the maximum number of bytes a sending host can transmit. The sending host can send multiple frames if the receiver has a window size large enough to accept them. When the receiver meets the window size, it stops and waits for permission (acknowledgement) from the receiver before sending more. To calculate the acknowledgement, add the first frame within this bursts sequence number to the total of all subsequent frame length fields; for example, A sending host sends 5 frames. The sequence number of the first frame within this stream has a sequence number of 10. Each frame contains 10 bytes of data. The receiving host acknowledges this with a value of 60 (starting sequence number 10 + 50 (5 frames multiplied by the total length in bytes). The receiving host then acknowledges the receipt of all 50 bytes of data and expects the 60th byte from the sending host. You can think of the acknowledgement as stating, Next I expect to receive Figure 8.4 shows an output screen taken from a Sniffer of a file transfer between hosts and how the calculation works for this particular example. Note the starting sequence number,
215
number of frames sent, amount of data in each frame, and the acknowledged value. To calculate the acknowledgement, add the starting sequence number to the number of frames, multiplied by their length in bytes.
Acknowledged value Number of frames sent
Starting sequence number
FIGURE 8.4
Note that the Sniffer output details information from frame two, which is highlighted.
Amount of data in each frame
In the first frame shown in the top pane of the Sniffer summary screen, you can see that two FTP hosts (client 192.42.252.20, FTP port 2918, and FTP server 192.42.252.1, port 20) already have a functioning TCP session. In this frame the server now expects the client to now send data beginning with sequence number 46348289, indicated by the ACK value in this frame. Notice that the next four frames sent by the client carry FTP data. Look in the detail pane. As expected, the starting sequence number is 46348289, and the total amount of FTP data contained within each of these four frames is 1024 bytes (indicated at the end of the TCP header). Apply the formula and check the math (starting sequence number plus the number of frames sent multiplied by the amount of data in each frame). If the starting sequence number is 46348289 (frame 2) and the client sends four frames with a length of 1024 bytes (frames 25), the server expects 46352385 as the next sequence number. You can verify the formula with the acknowledgement value sent by the server. It appears in the last frame (frame 6) as 46352385.
Data Offset
The 4-bit data offset field indicates where the start of upper-layer data that follows the TCP header begins. Because the length of a TCP header can vary in size when it has certain options
216
TCP/IP PRIMER PLUS
present, data offset is necessary. TCP uses it to accurately predict where the first byte of upperlayer data is to be expected within the frame.
Reserved
The six-bit reserved field is reserved for future use and is always represented by zeros.
Control Flags6 Bits

The 6-bit control flags field indicates to the receiver the purpose of the frame. Figure 8.5 shows the six different control flag fields.
FIGURE 8.5
TCP uses control flags to indicate to the receiver how to process the data.
ACK RST FIN
URG PSH SYN
The following describes the functions of the six one-bit control flag fields: URG (Urgent) Set by sending host to indicate that data contained within this frame has high priority. When the sending host sets this bit, the Urgent Pointer, which appears under the URG bit, identifies (or points to) the next byte in the frame following the urgent data. ACK (Acknowledgement) The sending host sets this bit to indicate that this frame includes an acknowledgement of previously received data. PSH (Push) Each TCP session controls when data received is passed to upper-layer applications for processing. When the sending host sets this bit, the receiver must not wait; instead it must send the data (push) immediately to the upper-layer process. By setting this bit the sending TCP host forces the receiving TCP host to pass the data up without delay.
217
RST (Reset) Set when user aborts a session or an error occurs in a connection to indicate the session should be reset. SYN (Synchronization) sequence numbers. FIN (Finish) sending data. Establishes a session between ports/sockets by synchronizing
Closes an established session and indicates that the sender has finished
Window
The amount of data that a host can receive varies, depending on the hosts resources and how many transmissions that host is currently receiving. The two-byte window field defines the maximum amount of data in bytes that a TCP host can receive. A host uses this field for flow control. A window size of zero indicates that this host cannot receive data at this time. This typically indicates congestion or a lack of resources.
Checksum2 Bytes
The two-byte checksum field is used to detect bit damage that might have occurred during transit. The checksum verifies the bits within the TCP header, a pseudo IP header, and the upper-layer data. The checksum is calculated by the sending host and compared to the receiving host for validity. If the checksum does not match, the receiving host trashes the frame and gives no notification to the sending host. The sending host assumes responsibility for detecting the lost frame and retransmits. TCP keeps track of information contained within the IP header, such as source and destination addresses, to assist in detecting problems such as improperly routed frames.
Urgent Pointer
The 2-byte Urgent Pointer field exists only when the urgent (URG) bit has been set. When the sending host sets the urgent bit, the Urgent Pointer identifies the byte in the frame that follows the urgent data to clearly identify where nonurgent data begins.
TCP OptionsVariable Length

TCP options field can be variable lengths, depending on the options chosen by the sending host. For example, the sending host could choose maximum segment size, which indicates the largest segment size this TCP host will accept. Without this option, the host would accept any segment size. The maximum segment size (MSS) option is the most commonly used option. A complete discussion of options is well beyond the scope of this book.
TCP
The length field (which is a variable length field) identifies the total length of the TCP header and subsequent data, and does not include the TCP pseudo header information. Because the
218
TCP/IP PRIMER PLUS
size of the TCP header and its subsequent data varies, this value also varies. Although TCP includes the TCP length field as part of its header, the TCP length field does not actually appear in the TCP header in a Sniffer (protocol analysis) detail output. The TCP pseudo header provides error control on the IP header and detects misdirected frames. It ensures that the correct destination host receives a sent datagram. TCP does not include the information contained in the pseudo header. TCP stores this information in a TCP memory buffer called a TCB (transmission control block). Figure 8.6 shows an example of a TCP pseudo header.
FIGURE 8.6
IP Source Address IP Destination Address Zero IP Protocol TCP Length
The TCP pseudo header allows TCP to doublecheck that the datagram has arrived at the correct destination.
Fundamentals of TCP Operation

TCP provides a bidirectional communication pipe between remote host processes, identified by ports. As described within RFC 793, TCP controls the communications between these processes by providing the following: Connection setup and teardown Multiplexing Data transfer Flow control Reliability Precedence and security TCP can be thought of as the Fed-Ex of protocols, which boasts When it absolutely, positively has to get there overnight! In other words, it guarantees delivery of packets. TCP actually can boast a speedier delivery of packets than Fed-EX; however, TCP still remains slower than UDP (which provides no reliability). Achieving such a high standard of delivery involves overhead in the form of establishing, maintaining, and terminating sessions between hosts. Unlike connectionless protocols, TCP does not rely on lower layers to track data. TCP does not limit itself by only identifying the sending and receiving host process, placing data on the wire, and hoping it arrives at its destination without any follow-up. TCP uses sequencing and acknowledgements to guarantee the delivery of packets.
219
Unlike its counterpart UDP, when TCP receives a stream of data (messages), it breaks the streams into segments and assigns sequence numbers to each byte prior to delivery by IP within a datagram. These sequence numbers require corresponding acknowledgements to be returned from the destination to ensure it has received from the sender each segment within the datagram. TCP maintains a copy of the segments contained within a buffer at the host, known as a TCB (transmission control block). If it does not receive an acknowledgement, it assumes the datagram has been lost and retransmits it. We discuss this in more detail later in this chapter.
Connection Setup and Teardown

To provide reliable data delivery between processes, TCP must make a connection before the upper-layer applications can exchange any meaningful data. To accomplish this, TCP establishes a connection known as a logical circuit between the remote host ports first. This connection links ports or processes running within each host. TCP maintains this connection throughout the entire conversation and tears down the connection when it is no longer needed. Once IP learns the logical address of the destination host, TCP sets up a session that provides the reliable foundation for the upper-layer protocols to deliver data. When the user or one of the hosts requests to close a session, TCP tears the session down. We discuss the session setup and teardown procedures and exchanges in more detail later in this chapter.
Multiplexing
Multiplexing capability enables TCP to establish and maintain multiple communication paths between two hosts simultaneously. Multiplexing also allows a single host to distinguish and maintain sessions with many hosts simultaneously. Hosts need this capability because usually they run multiple applications or services such as Telnet, FTP (File Transfer Protocol), or other services. TCP has to distinguish one process from another, and manage and maintain the communications for these processes. To accomplish this, TCP utilizes ports to differentiate communications and manage them (see RFC 1078 TCP port service Multiplexer TCPMUX). As mentioned in Chapter 6, Routing Protocols, there are two main port types: server ports and client ports. Server ports identify major applications or services; for example, Telnet (port 23), SMTP (port 25), and FTP (ports 20, 21). Client ports vary; they are chosen on the fly and dynamically applied, ranging 102465535. Each time a host starts a process it causes a port to open, allocating resources to that process. When the process no longer needs the port it closes the port, releasing the resources associated with that port for reallocation. TCP uses these ports to identify which process on the sending host should be linked to which process on the destination host. The port on the host, along with the Network layer (DoD Internet) logical IP address, identifies a unique process on a host, referred to as a socket. Once the established TCP connection between hosts links them together, these two sockets, referred to as a socket pair (see Figure 8.7), form a connection. This pairing enables a host to distinguish among multiple connections from the same host or different hosts.
220
TCP/IP PRIMER PLUS
FIGURE 8.7
Note that the clients IP address, client port, servers IP address and server port make up what is called a socket pair.
Client Port 1004
Socket Pair
Telnet Server Port 23
192.16.1.5
192.16.1.1
192.16.1.8
Client Port 6000
Data Transfer
TCP receives and organizes streams of data (messages) from upper-layer processes or applications as segments and passes them down to be formatted as datagrams by IP (Network layer) for addressing, packing, and delivery. When IP receives datagrams from a remote host, it inspects the protocol address within the IP header to determine whether to send the information through TCP or UDP for processing. Figure 8.8 shows an IP header referencing TCP as the upper-layer protocol.
FIGURE 8.8
TCP passes down segments to IP (Network layer) for conversion to datagrams.
221
TCP runs on top of the Internet Protocol that provides Network Layer addressing and connectionless delivery of datagrams between hosts. The protocol type value 06 identifies TCP within the IP header. The protocol type value 17 identifies UDP within the IP header. When TCP receives segments within datagrams from IP it reassembles them into organized data streams (messages), identifies the receiving client or server port, and passes them on to the appropriate (upper-layer) application for processing. The upper (applications) and lower (Internet Protocol) layers have a bidirectional relationship depending on the direction of the data flow. TCP provides the same fundamental services to all upper-layer protocols. This is a simplistic view of how TCP operates; we will discuss TCP operation in more detail later in this chapter.
Flow Control
TCP needs a method of controlling the inbound flow of data. Flow control guarantees that incoming traffic does not overwhelm a hosts receive buffer and that the receiving host can adequately process and respond to the sending hosts requests. The window mechanism identified within the TCP header provides this function. We will take a detailed look at flow control and the TCP header later in this chapter. Each end host maintains its own window and advertises this window to the other side. When congestion occurs, a host reduces its window size and advertises it to the other side. In effect, the host asks the other side to slow down its transmissions. When congestion no longer exists, a host can increase the size, alerting the other side that it can send more data. The capability to dynamically increase or decrease the window as needed is referred to as a sliding window. An administrator can configure the initial window size at the host. This configuration varies depending on the operating system used.
Reliability
Reliability comes from TCPs guaranteed delivery of packets. TCP requires the sequencing of each byte sent and a corresponding acknowledgement of each byte from the other side. This enables a host to detect whether information has been lost or sent out of order. The receiving host does not send an ACK if datagrams become lost in transit. The transmitting (sending) host has the task of detecting lost or missing frames and retransmits if necessary. If the sending host does not receive an acknowledgement within a specified period of time, it retrieves a copy of the previously sent information from its TCB buffer and retransmits the lost data. The sending host uses a timer based on a round-trip delay calculation to detect a lost frame and retransmit. If a timer expires before receiving an acknowledgement of sent data, the sending host assumes the datagram is lost and retransmits. TCP deals with damaged frames through a CRC field contained within the TCP header. The sending host performs a CRC calculation before transmitting. The receiving host performs a CRC check upon receipt to determine whether a datagram has been damaged while in transit.
222
TCP/IP PRIMER PLUS
If the receiving host detects a damaged datagram it simply trashes the frame without notifying the source host. Eventually, the source host realizes something has happened to this frame because it has not received a corresponding acknowledgement from the receiving host. At this point the TCP timer expires, causing this host to retransmit the data.
Precedence and Security

The DoD mandates that all protocols implemented within its networks support a multilevel security model and precedence levels. TCP can utilize the service and security options within IP to provide this level of service to upper-layer applications. Figure 8.9 shows the options available within the Type of Service field. TCP offers these types of services to upper-layer applications: Precedence Delay Throughput Reliability The options within the Type of Service field of the IP header indicate how a datagram should be handled. When implemented, the Type of Service options, precedence delay, throughput, and reliability influence route selection when delivering datagrams. For example, if an application requires a datagram to be sent by a fast path when there is more than one path to a destination, it can request routers to send the frame over the path offering the lowest delay.
FIGURE 8.9
ToS bits influence how a datagram should be handled.
223
The first option, known as precedence, indicates whether this datagram carries routine or highpriority (precedence) information; the higher the precedence level, the higher the security level. A host with a mismatched or lower precedence (security level) cannot establish a connection to a process with another host having a higher security level. Thus a host rejects a connection request based on a multilevel security basis. Although the IP header contains the Type of Service options, TCP can make use of these functions on a per-connection basis through bi-directional communication. TCP can store these options in its TCP memory buffer to provide increased security and more efficient delivery of application data.
Connection-oriented Characteristics
As we discussed in Chapter 6, protocols fall into one of two categories: connection-oriented or connectionless. As a connection-oriented protocol, TCP implements all six of these basic characteristics: Session setup Teardown Sequencing Acknowledgements Keepalives Flow control The following sections detail how each of these basic characteristics work.
Session Setup
Before any data transmission can occur, a reliable connection-oriented logical circuit needs to be established between remote hosts communicating processes or applications. Session establishment remains the same regardless of the process. TCP identifies all upper-layer processes and applications using a port or socket address. TCP uses these port addresses to distinguish one process from another within the same host, which ensures proper delivery and processing. For example, when a user wants to initiate a Telnet client session with a remote Telnet server, the user starts a local Telnet client process. This initiation causes the local host to open a source client port identifying this Telnet process using a variable port value within the range 102465,535. TCP uses this source port along with a destination port (well-known port 23 for Telnet), which indicates the intended recipient of this message. Using both the source port and the destination port enables TCP to keep track of a pair of communicating processes and know the processes between which it is opening a session.
224
TCP/IP PRIMER PLUS
If a user initiates a session with a remote host using a host name rather than an IP address, some type of name resolution must occur that maps the host name to a Network layer address of either the ultimate destination (if on the same subnet) or the gateway. After learning the Network layer address of the destination IP host, ARP resolves this address to a MAC address for local delivery.
Socket Pairing
Once the address resolution process has been completed, TCP has enough information to begin the session setup process. The source Network layer address, client port/socket, and destination Network layer address and server port/socket make up what is called a socket pairing. Because the same client or multiple clients connecting to the same remote server port/socket can request multiple TCP connections, socket pairing separates the different requests, uniquely identifying and handling the communication between pairs. Because of the potential multitude of connections, socket pairing remains critical to TCPs success. Session setup begins by the TCP client setting a bit, known as the SYN bit, within the TCP header indicating a request for synchronization with the destination TCP process. The receiving hosts TCP session must ACK the receipt of this SYN request and send its own SYN request. This SYN also must be acknowledged by the previous host. Figures 8.10, 8.11, and 8.12 comprise an example of a session setup. The summary screen shows two hosts (192.42.252.20 and 192.42.252.1) in the process of establishing a TCP connection. The first frame indicates that host 192.42.252.20, using a client port of 2921, requests a TCP connection by sending the initial SYN to the Telnet server, indicated by port 23 and IP address 192.42.252.1.
Frame 1
FIGURE 8.10
The first part of a TCP session setup starts by the client sending the server a SYN. Notice this frame does not contain an ACK field because neither client nor server has sent any previous data to acknowledge.
225
The Telnet server sends the second frame, which serves as an ACK of the previous SYN sent by the client and a new SYN request sent by this host. Notice this frame carries an ACK field, which acknowledges the initial SYN by the client. Because TCP can communicate in fullduplex mode, which means it can send and acknowledge receipt of data within the same frame instead of requiring a separate frame to perform this function, this host can include its SYN request within the same frame. This allows TCP to operate more efficiently
Frame 2
FIGURE 8.11
The second part of a TCP session setup is the servers acknowledgement (ACK) of the clients SYN and sending its own SYN request to the client.
The client sends the third frame as an ACK of the previous SYN sent by the Telnet server. Now that the two hosts have established a TCP session they can transmit Telnet data. Note that no matter what type of upper-layer applications a host requests (Telnet, SMTP, FTP, and so forth), this three-frame exchange process always occurs. The requests and acknowledgements found in the frame exchange are known as the three-way handshake. Because TCP has the capability of full-duplex communication, it needs only three frames instead of four to complete this process. When the destination receives the first SYN request from the sender, the destination responds by acknowledging the sender with its own SYN request within the same frame. To complete the transaction, the sender sends its ACK that it has received the destinations SYN request in the next and final frame of the three-way handshake. Figures 8.13, 8.14, and 8.15 comprise a detailed example of a three-way handshake. As you can see within the TCP header, the host has set the SYN bit (indicated by a value of 1). In addition, the host has stated several starting parameters, such as its ISN (initial sequence number 1545216000), window size (4096 bytes), and maximum segment size (1024 bytes). We will discuss these values in more detail later in this chapter.
226
TCP/IP PRIMER PLUS
Frame 3
FIGURE 8.12
The third part of a TCP session setup is the client acknowledging (ACK) the servers SYN.
FIGURE 8.13
Note the SYN sent by the client in the first part of the three-way handshake.
Figure 8.14 shows the response frame from the Telnet server (IP address 192.42.252.1, source port 23). Notice the server includes its ACK indicating that it has received the clients initial request (sequence number 1545216000). The acknowledgement states that this host next
227
expects sequence number 1545216001, which implies that it received all sequence numbers up to, but not including this value. You also can see the Telnet servers ISN of 49856000. The server has set the SYN bit indicating that it would like to synchronize with the client, setting its window size to 4096 bytes and maximum segment size to 1024 bytes.
FIGURE 8.14
Note the ACK and SYN sent by the server in the second part of the threeway handshake.
The client sends the last frame of the three-way handshake to acknowledge receipt of the servers previous SYN request. This host acknowledges receipt of the Telnet servers previously sent sequence number by indicating that it next expects to receive sequence number 49856001. Both hosts have synchronized and know each others starting parameters. Within the SYN request frames TCP includes starting parameters that must be agreed upon by both ends to successfully synchronize their sessions and begin the process of sending meaningful user data. These parameters include their receive buffer size (which is elastic), initial sequence number to be used when data transmission begins, and the optional maximum segment size this TCP host can accept. We will discuss these parameters in more detail later in this chapter.
Session Teardown
The user or TCP can request a session teardown. If a user no longer wishes or needs the services of the remote application, he or she can exit the local application, causing a session teardown request to be sent. The TCP session teardown process is similar to the session setup. It utilizes a three-frame exchange to close the session. Either side can request a teardown. Host 192.42.252.1, sequence number 49856607, sends the initial teardown request in the first frame, indicated by the FIN (Finish) request. Figures 8.16, 8.17, and 8.18 illustrate an example of a session teardown request.
228
TCP/IP PRIMER PLUS
FIGURE 8.15
Note the ACK sent by the client in the second part of the three-way handshake.
Frame 1
FIGURE 8.16
A FIN is sent as the first part of the session teardown.
The recipient sends the second frame acknowledging the previous FIN request and expects to receive a subsequent sequence number 49856608. Additionally, this host sends its own FIN request with sequence number 1545216061. The host that initially requested the teardown
229
sends the final frame, acknowledging the previous FIN. This closes the connection and the hosts cannot exchange upper-layer information until they establish a new TCP session.
Frame 2
FIGURE 8.17
As the second part of the session teardown, the host sends an ACK and its own FIN request.
Frame 3
FIGURE 8.18
As the third and final part of the session teardown, the host acknowledges (ACK) the other hosts FIN request.
230
TCP/IP PRIMER PLUS
TCP sends a similar request when an unrecoverable error or denial of access occurs in a TCP session setup. When one of these problems occurs, it causes either the client or server TCP process to issue the teardown request. Whatever the reason for the teardown, it uses a threeway handshake to accomplish the session teardown. Just like the session setup sequence, the teardown process uses a three-frame sequence. The host requesting session closure sets a FIN bit within the TCP header indicating a request to close the session; it then sends the FIN bit to the other side. The recipient must in turn acknowledge receipt of the initial FIN and send its own FIN, which then is acknowledged by the original host requesting to close the session. At this point both sides release the allocated resources and make them available for other processes.
Sequencing and Acknowledgements

The cornerstone of TCPs services is to provide the most reliable transmission of data. To guarantee the delivery of datagrams, TCP sequences each byte of data it sends. This might seem like overkill because many protocols sequence each datagram regardless of the byte size; however, this guarantees that all sent data is tracked. Tracking all the sent data can detect and correct lost data, duplicated data, and data delivered out of order. Each time a host sends data, TCP assigns a sequence number to each byte and waits for a positive ACK of the assigned sequence numbers from the other side within a specific amount of time. (An algorithm, which we will discuss later in the chapter, calculates this time.) If the receiver does not respond within that specific amount of time, the sending host retransmits the data. The receiver utilizes the same sequence numbers to acknowledge receipt of data to detect missing, sent out of order, or duplicated data sent by the other side. Once the receiver has the sequenced data it can reorder these segments into data streams (messages) to be passed to the upper-layer process or application for processing. The receiving host buffers incoming TCP segments before passing this information up to the application and uses sequence numbers to detect whether it has received data out of order. Because datagrams might take very different paths before reaching their destinations, a significant delay can occur for some of these segments. The receiving host acknowledges data received in sequential order. For example, if a sending host sends sequence numbers 1, 2, 3, and 4 but the destination receives only 1, 2, and 4, the receiver acknowledges only segments 1 and 2 by sending ACK=3. The receiver buffers segment 4 in hopes that segment 3 will appear shortly. If segment 3 does not arrive at the destination, the sending host has to retransmit the data. Hopefully, segment 3 arrives and the receiver puts the segments in order, acknowledging receipt of 3 and 4 and passing this information up for processing. During the session setup process each end hosts TCP session uses an algorithm to derive a starting sequence value to be used for data exchange. Within their initial SYN frames, each host advertises its own starting sequence value. Figure 8.19 shows an example of a TCP session setup with the initial sequence number and SYN bit set.
231
FIGURE 8.19
Note this host advertises an initial sequence value of 1545216000 during the SYN request exchange.
Each side of the connection can send and acknowledge data within the same datagram. This datagram has a sequence field and an acknowledgement field. The sequence field indicates the starting sequence of the first byte of data being transmitted within this datagram. The acknowledgement field indicates the receipt of data from the other side up to, but not including the sequence number reflected, which represents the value expected in the next datagram sent. Once both sides establish a session, the sender sequences each byte and the receiver acknowledges each byte. Every TCP header has a length field indicating in bytes how much data has been transmitted within this datagram. The destination adds this value to the starting sequence number sent by the source to determine what the acknowledgement value should be upon the return. For example, if the sending host has a sequence number of 100, he sends 100 bytes of data (representing the length in bytes). The receiving host would then send in the response frame an ACK of 200, which represents the starting sequence number expected in the next datagram. To figure the formula during sequencing, the starting sequence number (in this case 100) plus length in bytes sent (in this case 100) equals acknowledgement (200). Apply this formula to the frames in Figures 8.20 and 8.21. Telnet provides a great example, as it typically sends data only one byte at a time, making it easy to understand how sequencing and acknowledgements work. The first frame shows that host 192.42.252.20 has sent the one byte of Telnet data by looking at the Telnet header. You can see the character being transmitted as 1. Look at the end of the TCP header and note in brackets [1 byte(s) of data] is being transmitted. This is the length field. Also note the sequence number of this frame, 1545216045. Use the formula to anticipate
232
TCP/IP PRIMER PLUS
what ACK value the recipient should respond with. Sequence number (1545216045) plus length (1) equals 1545216046. The second frame shows the response to the first frame. The Telnet server acknowledges receipt of the 1 (length field) sent by sending an ACK value of 1545216046, just as we expected.
FIGURE 8.20
TCP sequences every octet.
FIGURE 8.21
TCP acknowledges each octet.
233
Retransmission
The sending host determines whether a datagram needs to be retransmitted. Because datagrams can take separate paths and might get lost, the sending device keeps a copy in case it needs to retransmit a datagram to a destination host. When the source host sends data it places a copy of the data into a retransmission queue in case this information needs to be resent and starts a timer. If the sending host receives a corresponding acknowledgement in response to the previously sent information, it deletes the copy from its queue. If the sending host does not receive a response, or if the timer expires, it assumes the datagram is lost in transit and retransmits the datagram from the queue.
Timers
An algorithm calculates the value of the retransmission timer based on the amount of time it takes between sent datagrams and receipt of the corresponding acknowledgements. This algorithm dynamically calculates the retransmission timer by evaluating the time between a transmitted datagram and its subsequent acknowledgement. It then uses this result to compute an SRTT (smooth round trip timer). The SRTT uses this value and a base value configured on the host to calculate an RTO (retransmit timeout) value used by the host. An administrator can change the base value to affect the RTO of a TCP host. The configuration of this parameter varies depending on the operating system in use. Its not critical that you know the exact algorithm the host uses; only that this value controls how long a TCP host waits for an acknowledgement before it assumes a previously sent datagram has been lost and needs retransmission. Figure 8.22 shows an example of TCPs timeout and retransmission. In it host A sends sequence #11 and #12 to host B. Host B acknowledges receipt of those sequence numbers with ACK=12 and ACK=13. By sending ACK=13, host B next expects to receive sequence #13 from host A. Host A sends sequence #13 and a transmission error occurs somewhere in the path, causing the frame to be lost. Because host A does not receive an acknowledgement from host B, the transmit timer expires. At this point host A assumes that the frame was lost in transit and retransmits sequence #13.
FIGURE 8.22
Timeout and Retransmission
If a host does not receive an acknowledgement, it retransmits the data.
Host A
Host B
Sequence #11
11 Ack = 12
Sequence #12
12 Ack = 13
Sequence #13 Transmit Timer Expires!! Retransmission of Sequence #13
13
Lost
13 Ack = 14
234
TCP/IP PRIMER PLUS
Because of the wide fluctuations in bandwidth and transmission speeds of networks, sometimes the retransmission timer cannot keep up with the transmissions. This situation occurs when the base value on a host needs adjusting. If the retransmission timer is too low in value, a host might retransmit a datagram too quickly. In this case, a destination host sends an acknowledgement for the previous frame but before the host actually receives it, the retransmission timer expires. The source host then assumes that the destination host did not receive previously sent frame and retransmits another copy. This scenario causes duplicate datagrams to be sent, adding more traffic and congestion (needless traffic) to the network load. This type of needless traffic tends to be especially problematic on slow WAN links because resources are at a premium. If the opposite is true (the base value of the timer is too high), it could slow so much that connections drop. If the sending host cannot detect and retransmit lost datagrams within a timely manner, applications might give up and close the connection.
Keepalives
Every connection-oriented protocol needs some way to maintain the logical circuit between communicating processes even when no data is being exchanged; TCP is no exception. To maintain the logical circuit TCP sends a datagram called a keepalive in which no upper-layer data is present. It uses these types of datagrams to keep the session alive; hence the name. Because the frame contains no data, the length field value is zero, which means the subsequent ACK number does not advance.
Congestion
TCP uses keepalives as a normal part of session maintenance; however, this adds overhead to the network. Depending on how many open TCP connections you have on your network, keepalives can cause a large amount of unnecessary overhead to an already congested link. Note that connections to remote hosts, if unused, should be released (closed) and opened only when needed. Think about all the users you have on your network. Now think about all the shortcuts and mapped drive connections they have on their local computers that point to remote hosts. These shortcuts and mapped drives provide a quick and easy way for users to connect to remote hosts using their resources effortlessly. However, consider that for each of these quick references to exist each of these connections needs to be opened and maintained by TCP, even when they are not in use. Now go and disconnect them. Unmap drives that are not currently in use or after use. Limit the amount of desktop shortcut connections users can maintain. This cuts down on tons of needless TCP traffic and frees up critical bandwidth, especially on slower WAN links.
Flow Control
Flow control is a function of TCPs window feature. TCP uses flow control to manage the flow of data into a receivers buffer to avoid overrunning the receiver. If a sending host transmits
235
data faster than a receiver can process it, the receiver asks the sender to throttle back and send less data until the receiver can accept more. Sometimes the receiver receives an overwhelming amount of data. If this occurs, it sends a choke packet to tell the sender to stop sending entirely. If the situation grows to a critical level, it might even close the TCP session. The TCP header contains a field known as the window (see Figures 8.2 and 8.3 for an example within a TCP header). With each frame exchange, including the initial session setup (the SYN frame), each side of the conversation advertises to the other end the current size of its receive buffer. Figure 8.23 shows an example of a window advertisement.
FIGURE 8.23
Notice that both hosts advertise a window size of 4096, or WIN=4096.
For example, if a host claims in its initial SYN frame that it can receive 4096 bytes of data by stating WIN=4096, the peer host cannot send more than 4096 bytes of data. Each hosts window size becomes the peer hosts send window, which means that a sender cannot send more than a receiver says it can receive. After the initial synchronization each frame carries the current hosts receive window size, which is measured in bytes. Hosts can adjust the window size within subsequent frames to indicate a smaller buffer when they have congestion or expand when congestion alleviates. For example, if a host attempts to maintain several client sessions, it could quickly find it is running out of resources and needs to control the flow of data by decreasing the TCP window size advertised on some of these connections. By doing this it allows the host to properly and efficiently process the data it receives from all hosts in a timely manner.
236
TCP/IP PRIMER PLUS
If TCP had no mechanism for congestion control, some sessions could monopolize the hosts resources, causing other client sessions to time out and close. The window mechanism enables TCP to control the influx of traffic from a TCP session like a traffic cop. It increases the window size when it has plenty of resources to process requests (giving the green light to incoming traffic). It decreases the window size when it starts to experience congestion, asking sending hosts to slow down (giving the yellow light to incoming traffic). It stops traffic entirely when overloaded and advertises a window of zero, referred to as a choke packet (giving the red light to the sending host to stop transmitting entirely). Figure 8.24 shows the various stages of windowing. Initially host B gives host A the green light, advertising that it can accept 4096 bytes as its window size. Host A responds by sending four frames containing 1024 bytes each. Host B, now experiencing congestion, advertises 1024 bytes as its window size, telling host A to slow down its transmissions (yellow light). Host A responds by sending the maximum window amount 1024 bytes of data. Host B, overwhelmed by the amount of transmissions it has received, responds by advertising a window of zero. By advertising Window=0, host B gives host A the red light, asking host A to stop sending data until it can accept more transmissions.
FIGURE 8.24
Host A Sliding Window Operation Host B
A host can control flow by telling the other the host to slow down, speed up or stop the transmission of frames.
Window = 4096 bytes Segment #1 Segment #2 Segment #3 Segment #4 1024 Window = 1024 Segment #5 1024 Slow down! Window = 0 Stop sending! 1024 1024 1024 I can accept up to 4096 bytes!
The sender uses the window as an indication of how much data it can send before the receiver must give it permission (by sending an ACK) to send more. If a zero window condition continues for a lengthy period of time without transitioning to a positive window size, eventually it forces the connection to close. Note that even if a zero window condition exists on a host, that host can still transmit data but can receive only critical frames such as ACKs and those carrying the RST (reset) or URG bits. Figure 8.25 shows an example of a zero window condition. When a host advertises a zero window, it indicates to the sending host to stop sending data until it advertises a positive window size. When a host advertises a zero window, usually this indicates it has limited resources or is busy servicing other hosts and might be overwhelmed.
237
FIGURE 8.25
A host can stop the sending host from transmitting any more data with a choke packet.
A zero window does not pose a problem unless it occurs frequently. When a host continuously advertises a zero window, this usually indicates that a host needs more memory, CPU power, or applications offloaded to other hosts. A zero window that persists for a lengthy period of time will cause connections to close.
TCP Ports
TCP uses well-known ports to establish a client-server relationship. TCP uses these ports at the Transport layer to identify which upper-layer processes have sent or should receive data streams. Table 8.1 lists many of the well-known TCP port numbers.
TABLE 8.1 Decimal 20 21 23 25 49
Well-known TCP Port Numbers

Keyword FTP-Data FTP Telnet SMTP LOGIN Protocol(s) TCP TCP TCP TCP TCP Description File Transfer Protocol (Data) File Transfer Protocol (Control) Telnet Simple Mail Transfer Protocol Login Host Protocol
238
TCP/IP PRIMER PLUS
TABLE 8.1 Decimal 53 63 70 80
Continued
Keyword DNS VIA-FTP Gopher WWW Protocol(s) TCP/UDP TCP TCP TCP Description Domain Name Service VIA-Systems-FTP Gopher File Service World Wide Web Services
Summary
RFC 793 defines TCP. Since its invention, TCP has become a standard protocol used on the Internet, providing guaranteed delivery of data between hosts. It provides a bidirectional communication pipe between remote host processes, identified by ports. TCP controls the communications between these processes by providing connection setup and teardown, multiplexing, data transfer, flow control, reliability and precedence and security. Because TCP guarantees delivery of data, it requires the sequencing of each byte sent and a corresponding acknowledgement of each byte from the other side. TCP accomplishes this in what is called a three-way handshake. To manage the flow of data into a receivers buffer, TCP utilizes flow control. Through the window mechanism contained in the TCP header, a receiver can ask the sender to slow down, speed up, or stop transmitting depending on how much data its buffer can accept. This process is called a sliding window, or windowing.
Review Questions
1. During TCP operation, what six fundamental functions does TCP use to control the communications between remote host process? 2. What must occur before upper-layer applications can exchange meaningful data? 3. What allows TCP the capability to establish and maintain multiple communication paths between two hosts simultaneously? 4. TCP receives ___________ from upper-layer applications and organizes them into __________ to be passed down to the Network layer to become __________. 5. What mechanism controls the inbound flow of data? 6. How does TCP provide reliable delivery of packets? 7. What are the six basic characteristics of connection-oriented protocols?
239
8. What is socket pairing? 9. When does retransmission of data occur? 10. Name the different fields contained in a TCP header?
CHAPTER 9
USER DATAGRAM PROTOCOL (UDP)

UDP Operation UDP Ports UDP Header
he User Datagram Protocol (UDP) as described in RFC 768 offers fast, unreliable delivery of messages between applications running on remote hosts. UDP maps to the OSI Transport and DoD Host-to-Host layers, and is an alternative to the slow but reliable TCP protocol. Figure 9.1 maps UDP to the OSI and DoD reference models.
242
TCP/IP PRIMER PLUS
FIGURE 9.1
DOD
OSI
Notice that UDP maps to the Transport layer of the OSI model and to the Host-to-Host layer of the DoD model.
Host-to-Host
TCP or UDP
Transport
Internet
Network
Network Access
Data Link Physical
UDP Operation
Like TCP, UDP receives a stream of data (messages) from upper-layer applications or processes identified by ports. UDP at the Transport layer breaks down these streams of data into segments and hands them down to IP at the Network layer, packaging them as datagrams for delivery to the host across the internetwork. Protocol type 17 identifies UDP within the IP header. Figure 9.2 shows UDP identified in an IP header.
FIGURE 9.2
Notice that protocol type 17 identifies UDP within an IP header.
Unlike TCP, UDP does not set up sessions. As a connectionless protocol UDP does not sequence sent data or acknowledge received data. UDP assumes that some other protocol
Chapter 9 USER DATAGRAM PROTOCOL (UDP)
243
(usually an upper-layer protocol) will track whether the sent data has reached the destination. If the data does not reach its destination, UDP also assumes the upper-layer protocol will recognize this and request a retransmission of the data. Because UDP does not establish a connection, it has no logical circuit to establish before transmission. Because it has no logical connection between end hosts, it has no management responsibilities for maintaining a connection. UDP does not fragment; it only identifies the source and destination port. Unlike TCP, which breaks upper-layer applications bit streams into segments, UDP simply provides a bi-directional pipe between communicating devices. UDP relies on IP for fragmentation and reassembly. UDP operates on a very simple basisbest effort delivery. Whereas TCP guarantees the delivery of data by sequencing and acknowledging every single byte sent or received, UDP offers only best effort delivery, relying on other layers to detect and recover lost or missing datagrams. However, despite not being able to guarantee delivery of packets, UDP has one advantage over TCPspeed. UDPs simplistic nature drastically reduces the overhead involved with transmitting data, making it a much faster, yet unreliable alternative to TCP.
UDP Applications
Application vendors can implement TCP or UDP at the Transport layer depending on the type of service the application requires. For example, most printing applications run on top of TCP because most users want to guarantee a successful print job, rather than hoping it prints. Two upper-layer protocols, FTP (File Transfer Protocol) and TFTP (Trivial File Transfer Protocol) provide similar functions but implement different Transport layer services. Both FTP and TFTP provide file transfer capabilities between hosts. FTP utilizes the services of TCP at the Transport layer to guarantee the successful completion of file transfers, detecting and correcting any lost, missing, or duplicated datagrams. FTP usually is used for the transfer of critical data. TFTP provides the same file transfer services as FTP, except that it utilizes UDP for faster delivery and less overhead. This method of delivery has the drawback of being less reliable; however, as the name implies (Trivial File Transfer Protocol), TFTP is designed for quick delivery of small files (trivial files) between hosts. As you can see, vendors can choose which Transport layer protocol to implement depending on what type of service is more criticalspeed or reliability. TFTP assumes the following: Stability of the network infrastructure Only trivial delivery errors (if any) may occur We will discuss FTP in more detail in Chapter 12, File Transfer Protocol (FTP), and TFTP in Chapter 16, Trivial File Transfer Protocol (TFTP).
244
TCP/IP PRIMER PLUS
UDP Ports
As a connectionless protocol UDP does not sequence or acknowledge data. It simply identifies the sending (source) and receiving (destination) ports within the UDP header and relies on IP to package and deliver the information. Table 9.1 shows a list of common UDP ports (see Appendix C, TCP/UDP Port Numbers, for a complete list of UDP Ports).
TABLE 9.1 Decimal 53 67 68 69 80
UDP Ports
Keyword DNS BootPS BootPC TFTP SNMP Protocol(s) TCP/UDP UDP UDP UDP UDP Description Domain Name Service Bootstrap Protocol Server Bootstrap Protocol Client Trivial File Transfer Protocol Simple Network Management Protocol
UDP Header
In Chapter 7, Transport/Host-to-Host Layer we discussed the fields within the TCP header and their functions. TCP headers vary in length, depending on the TCP options in use, but always have a minimum of 20 bytes. However, the connectionless UDP contains minimal information in its header. By comparison, UDP headers are only 8 bytes in length. Figure 9.3 gives an example of a UDP header as defined in RFC 768. Figure 9.4 shows a tangible UDP header as it actually appears during implementation.
Note
Like TCP, UDP must identify the source and destination ports. Unlike TCP, UDP does not include sequencing or acknowledgements. UDP uses a checksum in the header, which only detects damaged frames.
FIGURE 9.3
This figure merely shows the format of a UDP header. A UDP header contains 8 bytes.
Source Port Length Data
Destination Port Checksum
245
FIGURE 9.4
As you can see, a UDP header does not contain much information.
Source Port
The first field within the UDP header identifies the source port. This 2-byte field, similar to the TCP source port field, identifies the sending hosts upper-layer application or process. The value of this port depends on whether the sending host is a client process or a server process. If it is a client process, the sending host chooses this port value within the range of 1,024 to 65,535. If this is a server process, such as a well-known application sending a request or responding to a client request, the value ranges between 1 and 1,023.
Destination Port
The second field in the UDP header, the destination port, has a 2-byte field. Similar to the TCP destination port field, it identifies the receiving hosts upper-layer application or process. The value of this port depends on whether the receiving host is a client process or a server process. If it is a client process, this port value varies within the range of 1,024 to 65,535. If this is a server process, such as a well-known application, the value ranges between 1 and 1,023.
Length Field
The length field, the third field within the UDP header, specifies in bytes how much data is contained within this datagram. This value includes the UDP header and the data following (upper-layer protocols and information). The length field will be a minimum of 8 bytes, which is the total value of the fields within this header plus any upper-layer data and information.
246
TCP/IP PRIMER PLUS
Checksum
Although the connectionless UDP has no mechanism for detecting and correcting lost, missing, or duplicate frames, it does have a minimal method of detecting damaged frames. The 2byte checksum, the fourth field within the UDP header, guarantees that the bits have not been damaged during transit. This does not correct damage frames; it simply detects and trashes them. The sending host UDP process initially performs the checksum, known as a CRC (Cyclic Redundancy Check), placing the resulting value within the UDP header. At the destination, the receiving hosts UDP process performs the same calculation to verify the contents of the header. If the CRC value finds the frames invalid, the receiving host assumes a transmission error has occurred and trashes the datagram. The checksum validates the following: The UDP header The upper-layer data Information contained within a UDP pseudo header The UDP pseudo header contains 12 bytes for the checksum computation within the UDP datagram. Note that the pseudo header contains certain fields from the IP header. However, the UDP pseudo header does not actually appear in the UDP header. UDP uses the pseudo header to ensure that data has arrived at the correct destination. Figure 9.5 shows an example of a UDP pseudo header.
FIGURE 9.5
IP Source Address IP Destination Address Zero IP Protocol UDP Length
A UDP pseudo header enables UDP to make sure IP has not delivered or accepted a datagram to the wrong location, whether an incorrect host or upper layer.
The pseudo IP header contains the following information: Logical source address Destination network layer address Transport layer protocol type code UDP length
247
The UDP pseudo header has its name because UDP does not actually include this information within its header; instead it keeps track of this information to guard against misrouted datagrams. The host stores this information in its memory and UDP accesses it for reference purposes.
Summary
RFC 768 defines UDP. UDP offers fast, unreliable delivery of messages between applications running on remote hosts. UDP receives a stream of data (messages) from upper-layer applications or processes. UDP at the Transport layer breaks down these streams of data into segments and hands them down to IP at the Network layer, packaging them as datagrams for delivery to the host across the internetwork. As a connectionless protocol UDP does not sequence sent data or acknowledge received data. UDP relies on other protocols to track whether sent data reaches its destination. Because UDP has no logical connection, this also means that it has no management responsibilities for maintaining a connection. UDP operates on a best effort delivery; although it cannot guarantee delivery of packets, the simplistic nature of UDP drastically reduces overhead and provides an alternative to the slower TCP. Application vendors can implement TCP or UDP at the Transport layer, depending on the type of service the application requires.
Review Questions
1. What RFC defines UDP? 2. What does UDP provide for applications running on remote hosts? 3. What protocol type identifies UDP in the IP header? 4. What relationship does UDP have with sequencing and acknowledging the receipt of sent data? 5. During UDP operation of transferring data, what does this protocol assume? 6. What management responsibilities does UDP have with maintaining a connection? 7. What does UDP offer that TCP doesnt? 8. What mechanism does UDP use to check only for damaged frames? 9. What three things does the checksum validate? 10. The UDP pseudo header contains what information?
CHAPTER 10
UPPER-LAYER PROTOCOLS

Application Layer Presentation Layer Session Layer Upper-layer Protocols
Introduction to Upper-layer Protocols

The Process/Application layer of the DoD model considers the three upper-layer protocols of the OSI modelApplication, Presentation, and Sessionas one layer. At the Process/Application layer, you can interact with the host to perform these user functions: File transfer (FTP or TFTP) Client/Server file operations through Sun Microsystems (NFS) Remote access (Telnet) E-mail (SMTP) Network management (SNMP) Name resolution (DNS) All the previously mentioned protocols have their own characteristics and reside at different layers of the OSI model, but sit on top of the DoD model as the single Process/Application layer. In this chapter we will discuss each layer in the OSI model, describe its function, and briefly describe each of the upper-layer protocols (ULPs). Figure 10.1 shows the different protocols that reside on the Process/Application layer and how it relates to the OSI model.
250
FIGURE 10.1
TCP/IP PRIMER PLUS
Note that the OSI model has three separate layers that reside in the Process/Application layer (the upper layer) of the DoD model.
ARPA Layer Protocol Implementation Hypertext Transfer File Transfer Electronic Mail Domain Names File Transfer Client / Server TELNET Protocol MIL-STD-1782 RFC 854 RFC 1034, 1035 RFC 783 Domain Name System (DNS) Trivial File Transfer Protocol (TFTP) Simple Mail Transfer Protocol (SMTP) MIL-STD-1781 RFC 821 Terminal Emulation File Transfer Protocol (FTP) MIL-STD-1780 RFC 959 Transmission Control Protocol (TCP) MIL-STD-1778 RFC 793
OSI Layer Network Management Application
Process / Application
Hypertext Transfer Protocol (HTTP)
Presentation
RFC 2068
Sun Microsystems Network File System Protocols (NSF) RFCs 1014, 1057 and 1094 User Datagram Protocol (UDP) RFC 768
Simple Network Management Protocol (SNMP) v1: RFC 1157 v2: RFC1901-10 v3: RCF 2271-75
Session
Host-to-Host
Transport
Internet
Address Resolution ARP RFC 826 RARP RFC 903
Internet Protocol (IP) MIL-STD-1777 RFC 791
Internet Control Message Protocol (ICMP) RFC 792
Network
Network Interface
Network Interface Cards: Ethernet, Token Ring, ARCNET, MAN and WAN RFC 894, RFC 1042, RFC 1201, and others Transmission Media:
Data Link
Physical Twisted Pair, Coax, Fiber Optics, Wireless Media, etc.
Chapter 10 UPPER-LAYER PROTOCOLS
251
Unlike the other layers in the OSI and DoD models, the upper layers do not appear transparent to the end user. Users access the upper layer directly though the hosts operating system. End users use the uppers layer to perform tasks like file transfer, network management, e-mail, and so on.
Application Layer
Many people confuse the application layer with applications such as Word, Excel, PowerPoint, and so on. Think of the Application layer as an open window that allows you access to the OSI model. The Application layer enables your applications to send data across the network. It simply allows access to the lower layersa window to the OSI model. For example, when you access your e-mail, you must specify the data you want to send. Of course, the Application prepares this data by adding header and control information for the peer layer before it passes it down to the next layer and eventually sends it out on the wire. The Application layer provides access to file and print services; for example, Microsofts SMBbased client redirector and the server responder, which are implemented as file system drivers (RDR.sys and SRV.sys, respectively). If you use Windows NT, your client redirector works as an Application-layer protocol. When you make a request for file and print services of a remote NT box, your redirector prepares that information for the next layer. The adjacent layer gets it ready to send over the wire. When it sends that information to the remote host, the receiving layer at the other end resides on the Application layer. This layer on the remote host corresponds with the server service; thus, the client requester piece and the server responder piece in Windows NT provide the requests and responses on behalf of an application (considered Application layer services). Remember that the Application layer provides an interface to your protocol stack. Application layer services include the following: Applications with network and internetwork services File and print services E-mail Web access and HTTP Telnet access on a remote host File transfer (FTP and TFTP)
World Wide Web and HTTP (Hypertext Transfer Protocol)

Although almost everyone on the planet knows about the World Wide Web (WWW), most do not know that the protocol HTTP gives users access to the Web. The key mechanism for WWW communication, HTTP, enables you to transfer Web documents from server to a
252
TCP/IP PRIMER PLUS
browser using TCP and a basic client/server architecture. Web pages consist of hypermedia documents. The prefix hyper means that a document can consist of links that refer to correlated documents; for example, links to Web pages that contain information about Picasso. The suffix media describes various items other than straight text, such as multimedia images. When you want to access a Web page, you type in the URL (Uniform Resource Locator). The URL identifies a specific Web page and each Web page has an assigned unique name that identifies it. When you type in a request, or URL, it invokes a Web browser (the client) to access the server to obtain the Web page that you desire. HTTP allows for the communication between a browser and a Web server or between the intermediate machines, such as gateways and firewalls. We will discuss HTTP in greater detail in Chapter 15, Hypertext Transfer Protocol (HTTP).
E-mail and SMTP (Simple Mail Transfer Protocol)

Electronic mail (e-mail) enables you to send messages across the Internet using a standard client/server architecture. The client/server architecture enables both sides to send, store, and receive messages. SMTP dictates the standard for the exchange of e-mail between machines. Mail systems use a technique called spooling. When you send a message to someone, the system stores the message (data) in a private area (called a spool) along with the delivery address (mailbox or e-mail address), senders name, recipients name and time the message was sent. The system then transfers the message to a remote machine (a background transfer). This enables the sender to continue using his or her machine after sending e-mail without waiting for the receiver to open the message. The remote client machine uses the domain name system (DNS) to map to the receivers IP address and forms a TCP connection to the mail server. When it succeeds, it transfers the copy of the message to the mail server, which stores it in its spool for the receiver to access. We will discuss SMTP in more detail in Chapter 13, Simple Mail Transfer Protocol (SMTP).
Telnet (Telecommunications Network)

Its three oclock in the morning and youd prefer to go back to sleep, but you need to check on a remote machine. Chances are you would want to use the Telnet protocol instead of driving all the way to work in your pajamas. Telnet enables you (the client) at a terminal to access a remote host (server). Using TCP, Telnet enables you to communicate directly from your keyboard as if connected to the remote machine. The path of data travels from your keyboard to your operating system (client) through a TCP connection to the remote operating system (server). Telnet uses a network virtual terminal (NVT) to allow for a canonical (a standard) representation of data. Telnet also allows for client and server option negotiation. Additionally, Telnet provides symmetry in the negotiation syntax, which allows for either the client or server of the connection to request a specific option. We will discuss Telnet in more detail in Chapter 11, Telnet.
253
File Transfer
Two protocols that provide file transfer service reside on the application layer: FTP (File Transfer Protocol) and TFTP (Trivial File Transfer Protocol). More people use FTP than TFTP; FTP accounts for a large portion of TCP/IP traffic. Both protocols enable you to transfer (read or write) files from your computer from a remote machine. Some companies have a file server in lieu of more expensive computers with local disk storage. Whichever protocol you employ, it dictates and enables the transfer of files between a client system and a server system. FTP uses two TCP connections: one for data and one for control. This guarantees transfer of files, although it is slower. TFTP uses UDP, which does not guarantee delivery of the file but enables fast file transfer between machines. We will discuss FTP in more detail in Chapter 12, File Transfer Protocol (FTP), and TFTP in Chapter 16, Trivial File Transfer Protocol (TFTP).
Presentation Layer
The Presentation layer is layer 6 of the OSI model, just below the Application layer. At this layer data still appears in message format to be passed down to the Session layer. The Presentation layer primarily provides a common data format across different platforms. In other words, the Presentation layer translates information from the Application layer into a language that all the other layers can easily understand. The Presentation layer has the following responsibilities: Data conversion and translation Compression/decompression Encryption/decryption Multimedia and sound Table 10.1 shows commonly used Presentation layer protocols.
TABLE 10.1 Types
Commonly Used Protocols

Protocols ASCII EBCDIC Encryption/decryption TIFF JPEG PICT GIF MIDI MPEG QuickTime
Text- and data-related protocols
Graphics or image-related protocols Presentation layer protocols
Multimedia protocols
254
TCP/IP PRIMER PLUS
Several protocols existed before the introduction of the OSI model, but are still used today within the modern OSI model. This means that only a few true Presentation layer protocols exist, and that most ULPs do not map neatly to the OSI model. Most vendors implement protocols that span the entire upper three layers, skipping layers or performing functions on all three layers. Vendors decide which layer ULPs will perform on which level; thus some protocols may perform Presentation layer functions, but perform other ULP functions as well. In short, a true Presentation layer protocol is hard to find. There is one true Presentation layer protocol: XDR (external data representation). Sun Microsystems utilizes XDR in its client/server-based Network File System (NFS) implementations. NFS uses this protocol, which is incorporated into the programming code to provide platform independence. We will discuss XDR and NFS in more detail in Chapter 18, Open Network Computing Protocols.
Session Layer
The Session layer resides on layer 5 of the OSI Model, below the Presentation layer. At this layer data still appears in message format to be passed down to the Transport layer. This is the last layer in which user data remains in message format before the Transport layer changes them into segments. Think of the Session layer as an activity coordinator. The Session layer coordinates dialog between two applications (an upper layer and lower layer). The Session layer then manages the communication activity of each side, monitoring the dialog and terminating the session when necessary. The Session layer also controls the type and efficiency of conversation between the two applications. Applications can communicate in full-duplex or half-duplex mode. Half-duplex allows only one device to speak (transmit) at a time, like a one-way radio. Full-duplex allows either side to transmit simultaneously. The Session layer includes the following protocols: NetBIOS SQL X Windows RPC
NetBIOS (Network Basic Input Output System)

Developed by IBM and Sytek, NetBIOS allows applications access to network devices. NetBIOS provides four main services: name service, session service, datagram service, and miscellaneous function. This book focuses on name service.
255
NetBIOS provides a simple way for users to access remote resources and service by using a name rather than an address. NetBIOS performs name resolution by transmitting a broadcast, querying the local segment for address resolution. Modifications to NetBIOS enable it to function at layer 3 by utilizing TCP/IP. We will discuss NetBIOS in more detail in Chapter 14, Name Resolution.
NFS (Network File System) and ONC Protocols

Originally developed by Sun Microsystems, NFS enables a set of cooperating computers to share online files as if they were local. The file sharing appears nearly transparent to the user. Some companies also utilize NFS to interconnect their file systems. NFS operates at the Application layer but requires two other protocols for functionality: XDR (eXternal Data Representation) and RPC (Remote Procedure Call). As the name suggests, XDR resides at the Presentation layer. RPC resides at the Session layer. The protocol group (XDR, NFS and RPC) is referred to as the ONC (Open Network Computing) protocols. Collectively, this family of protocols enables disparate systems to access files transparently, supporting PCto-mainframe technologies. A data representation language, XDR provides consistent data representation between different NFS implementations. A transport-independent messaging protocol, RPC enables transparent communication between a client and a server. We will discuss all the ONC protocol in more detail in Chapter 18.
Summary
The Process/Application layer of the DoD model considers the three upper-layer protocols of the OSI model to be one layer, referred to as upper-layer protocols. At this layer you can interact with the host to perform user functions. You can perform the following functions at this layer: file transfer, client/server file operations, remote access, e-mail, network management, and name resolution. The three layers of the OSI Model that comprise the Process/Application layer of the DoD model are the Application, Presentation, and Session layers. The Application layer enables your applications to send data across the network. The Presentation layer primarily provides a common data format across different platforms. The Session layer coordinates dialogs between network devices.
Review Questions
1. What three OSI layers does the Process/Application layer of the DoD model consist of? 2. What is the primary function of the Process/Application layer? 3. What protocols reside at the Application layer?
256
TCP/IP PRIMER PLUS
4. What is the primary function of the Presentation layer? 5. What is the primary function of the Session layer? 6. What are the ONC protocols and on what layers do they reside?
CHAPTER 11
TELNET

Telnet Client-server Relationship Telnets Basic Services Network Virtual Terminal (NVT) Telnet Options
Remote Access
The Telnet (Telecommunications Network) protocol enables a user running a client terminal session to access a remote host (or Telnet server) across TCP/IP Internets. Telnet operates with TCP as the connection-oriented transport using well-known port 23 and enables the terminal and host to exchange 8-bit characters of data. Designed to work with any host and any terminal, Telnet establishes a TCP connection with a remote host; it then enables you to type commands from a keyboard as if attached to the remote machines keyboard. With Telnet you can also read the remote hosts output. The Telnet client-server relationship runs transparently, which means it gives the appearance that the keyboard and output display attaches directly to a remote host. Figure 11.1 shows the implementation of a Telnet client and server and illustrates a series of events that must happen to establish a Telnet session: 1. When you start the Telnet session, an application on the machine becomes the client. 2. The client establishes a TCP connection with a Telnet server (remote host) using the standard TCP three-way handshake as described in Chapter 8, Transmission Control Protocol (TCP). 3. The client communicates over the TCP connection from the keyboard and display as if connected directly to the remote hosts terminal. 4. The server utilizes a pseudo terminal device. The pseudo terminal device describes the operating system entry point that allows a program such as Telnet to transfer data to another operating system as if coming from the same keyboard. Telnet was developed in the 1970s when end devices were very expensive and dumb, typically relying on a remote host for processing. Dumb terminals would transmit each character one at a time to the remote server, which would echo the command issued by the client back to their
258
TCP/IP PRIMER PLUS
screen. The clients needed this process because they had no place to store or process information. Today there are intelligent client devices that maintain their own resources and perform their own local processing if necessary, but they still must emulate the original model. Modern client devices now support transmission modes, such as line mode, making some Telnet implementations more efficient; however, not all implementations support this.
FIGURE 11.1
The data travels from the keyboard to the remote operating system.
Clients reads from terminal
TELNET client
Client sends to server
TELNET server Server sends to pseudo terminal
operating system users keyboard & display
Server receives from client
operating system
TCP/IP internet
Transmission Modes
There are various transmission modes, including character and line mode. Character mode means one character, or one byte, is transmitted at a timethe least efficient method of transmission. Line mode allows an entire line to be transmitted in one chunk, allowing for a more efficient means of transmission.
Despite its lack of sophistication compared to other protocols, administrators widely use Telnet as a remote administration and troubleshooting tool. Usually, Telnet client software enables the user to attach to a remote machine by specifying its IP host name or IP address. When a Telnet client requests a session using an IP host name, the client first needs to resolve that name to a logical Network layer address and then to a local hardware address. If a host attempts the connection using the Network layer address it only needs to perform the last two steps. Once the local host knows the local hardware address to use, it can address a datagram to the hardware address. TCP then can set up the connection between the hosts, making Telnet operational. We will describe name resolution in more detail in Chapter 14, Name Resolution. Telnet resides at the upper three layers (Application, Presentation, and Session) of the OSI model or the Process/Application layer of the DoD model (see Figure 10.1 in Chapter 10, Upper-layer Protocols). In the OSI model this arrangement has advantages and disadvantages. Telnet has the obvious advantage of an administrator making modifications to a device to which it is not directly attached. Additionally, the code is not embedded within the operating system, which makes it easier for an administrator to use.
Chapter 11 TELNET
259
However, Telnet is rather inefficient. Consider that each keystroke must travel 1. Through the operating system of the client. 2. From the client through the intranet or Internet to the server. 3. Through the servers operating system. 4. Back to the client, delivering the data to the application program the user is running. Meanwhile, data in the form of output display has to travel back to the client over the same path. This requires a lot of overhead; thus it is an inefficient use of resources. In addition, this process occurs over a TCP session, which requires that each transmission be sequenced and acknowledgements returned, adding more overhead. With Telnet you trade overhead for reliability.
Basic Services
RFC 854 discusses Telnets three basic services, and RFC 855 discusses the different Telnet options. We discuss the various Telnet options later in this chapter. Telnet offers three basics services: 1. Network Virtual Terminal (NVT), which provides a standard interface to remote systems 2. Capability for clients and servers to negotiate various options 3. Symmetric view of terminals and processes We will discuss the basic services Telnet provides in the following sections.
Network Virtual Terminal

Telnet communicates by using TCP/IP protocols and bases its communication on a set of network standards (also called the canonical or standard form) known as Network Virtual Terminal (NVT). The NVT provides transparency and support for a minimum level of options between remote clients and servers being used by either side. By implementing a virtual terminal as a front end, this hides the differences between the communicating devices and provides a common set of commands and characteristics, in a sense creating all communicating devices equal. During Telnet, the user or client end is responsible for mapping incoming NVT codes to the actual codes required to operate the users display device, making communication between disparate systems seamless. It also is responsible for converting keyboard sequences into NVT sequences. RFC 854 defines NVT as an imaginary device that forces the client operating system to map whatever type of terminal the user is on to the NVT, emulating a common terminal such as IBM 3270, VT100, VT200, and so on. The server then maps the NVT to whatever terminal type the server supports. When both ends convert their data into the canonical or standard form, they can communicate regardless of what kind of terminal each end has (for example, if one is DEC VT-100).
260
TCP/IP PRIMER PLUS
NVT ASCII
The defined NVT format uses a 7-bit ASCII code throughout the Internet protocol suite for characters and display devices. It transmits the 7-bit ASCII code in 8-bit octets with the most significant bit set to 0. The RFC defines the display device as a printer and requires it only to display the standard printing ASCII characters, the American Standard Code for Information Interchange, represented by 7-bit does and to recognize and process certain control codes.
ASCII
Many applications use ASCII code. Computers send messages in ASCII for you to read. These messages can range from error messages to status messages. ASCII represents both textual data (letters, numbers, and punctuation marks) and control characters, which are commands such as return and line feed.
This enables Telnet to operate between as many systems as possible because it accommodates the details of heterogeneous computers and operating systems. Some systems use different lines of text (for example, carriage control or linefeed character). To accommodate this Telnet defines how data and command sequences are sent across the Internet. Figure 11.2 shows the conversion process from the local host format to the NVT format.
FIGURE 11.2
NVT operation involves the conversion of user terminal and host format to and from NVT format.
TCP connection across internet Client Server
Servers System
Users keyboard and display
Client System format used
NVT format used
Server System format used
The NVT keyboard can generate all 128 ASCII codes by using keys, key combinations, or sequences, which include 95 characters that have printable graphics (letters, digits, punctuation marks) and share the same meaning 33 control codes Table 11.1 shows the standard control codes that all Network Virtual Terminal implementations must understand.
Chapter 11 TELNET
261
TABLE 11.1 Name NULL Line Feed
NVT Required Control Codes

Code NUL LF CR Decimal Value 0 10 13 Function No operation. Moves the printer to the next print line, keeping the same horizontal position. Moves the printer to the left margin of the current line.
Carriage Return
Table 11.2 shows optional control codes that still should have the indicated effect on the display whether understood by the NVT or not.
TABLE 11.2 Name BELL Back Space Horizontal Tab
Optional NVT Control Codes

Code BEL BS HT Decimal Value 7 8 9 Function Makes an audible or visible sign (does not move print head). Moves print head one character position towards the left margin. Moves the printer to the next horizontal tab stop. Remains unspecified how either end determines whether the location of tab stops. Moves the printer to the next vertical tab stop. How either end determines the location of the tab stops remains unspecified. Moves the printer to the top of the next page, keeping the same horizontal position. On visual displays this commonly clears the screen and moves the cursor to the top left corner.
Vertical Tab
VT
11
Form Feed
FF
12
Telnet Commands
Telnet NVT provides various commands that control interactions between the client and server and incorporates these commands into the data stream. The Telnet commands consist of a mandatory two-octet sequence and an optional third. Telnet uses the first octet to indicate that the information being sent is a command and should be interpreted as such, known as the Interpret as command (IAC) character. The second octet identifies the code for one of the commands listed in Table 11.3. The third octet further identifies the commands meaning when the previous command code is not enough. Table 11.4 shows the various TELNET options.
262
TCP/IP PRIMER PLUS
TABLE 11.3 Command EOF SUSP ABORT EOR SE NOP DM BRK IP AO AYT EC EL GA SB WILL WONT DO
Telnet Commands When Followed By IAC (255)

Decimal Code 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 Meaning End-of-file. Suspend current process (job control). Abort process. End of record. End of subnegotiation parameters. No operation. Data mark, portion of a Synch. Always accompanied with a TCP urgent notification. Break; indicates the break signal. Suspend, interrupt or abort the process. Abort output. Allows the completion of the current process but does not send output to the user. Are you there. Visible proof that the other end received the AYT. Erase character. The receiver should delete the last preceding undeleted character from the data stream. Erase line. Delete characters from the data stream back to but not including the previous CRLF. Go ahead. Tell other send that it can transmit. Subnegotiation of the indicated option follows. Option negotiation. Indicates the desire to begin performing, or confirmation that you are now performing the indicated option. Option negotiation. Indicates the refusal to perform, or continue performing the indicated option. Option negotiation. Indicates the request that the other party perform, or conformation that you expect the other party to perform the indicated option. Option negotiation. Indicates the demand that the other party stop performing, or conformation that you no longer expect the other party to perform, the indicated option. Interpret next octet as command.
DONT
254
IAC
255
Chapter 11 TELNET
263
Option Negotiation
Despite both sides assuming an NVT, Telnets first exchange takes place with an option negotiation signal. Clients and servers use option negotiation to agree on features and options to be implemented during communication. Telnet treats both sides of the connection symmetricallyeither side can request the use of an optional feature. If the other side does not support the feature or is prohibited from using this feature, it rejects the request. Both sides agree upon and use the supported features and keep all other options at the minimum NVT standard. Once the client and server complete negotiation, they can begin to exchange data over the Telnet session. Either side can send the following four requests: WILLSender wants to enable the option. DOSender wants the receiver to enable the option. WONTSender wants to disable the option. DONTSenders wants the receiver to disable the option. Figure 11.3 shows a Telnet session being set up by TCP using a three-way handshake. Figure 11.3 also shows negotiations between a client and a server as well as a client login. Notice TCP port 23 is the destination (D=23) port in the first frame.
FIGURE 11.3
Once the TCP session is set up (in frames 1, 2 and 3), the Telnet client and server negotiations begin, using WILL, DO, WONT and DONT exchanges.
264
TCP/IP PRIMER PLUS
Telnet Options
A Telnet client and server can negotiate a variety of options using commands at any stage of the connection. This symmetry allows either the client or server to reconfigure its connection. The RFCs describe each one of these commands separately. Although more than 40 options exist, Table 11.4 shows the most important and widely used options.
TABLE 11.4
Telnet Options
Name Binary transmission Echo Suppress go ahead Status Timing mark RFC 856 857 858 859 860 Meaning Change transmission to 8-bit binary. Permit one side to echo data it receives. No longer send go-ahead signal after data. Request for status of a TELNET option from a remote site. Request the insertion of a timing mark in the return stream to synchronize the ends of a connection. Exchange information about the make and model of the terminal in use. This enables programs to alter output like cursor positioning sequences for the users terminal. Terminate data sent with EOR code. Convey window size to a Telnet server. Exchange terminal speed information. Enables, disables, and regulates flow control. Use local editing and send complete lines; not single characters. Propagates configuration information.
Decimal Code 0 1 3 5 6
24
Terminal type
1091
25 31 32 33 34 36
End of record Window size Terminal speed Remote flow control Linemode Environment variables
885 1073 1079 1372 1116 1408
The client and server agree on options through a process of negotiation that result in a common view of various extra capabilities that affect the interchange and operation of applications. Like most Telnet operations either end can enable or disable an option either locally or remotely. The initiator of the communication sends a 3-byte command: IAC, (type of operation), (command) The receiver responds in the same 3-byte form.
Chapter 11 TELNET
265
In addition, TELNET allows for either side to accept or reject a request to enable an option, but requires a side to always accept a request to disable. Table 11.5 shows an example of possible Telnet scenarios given these four option negotiations commands: WILL, DO, WONT and DONT.
TABLE 11.5 Sender Sent WILL WILL
Various Possible Responses

Receiver Responds DO DONT Implication Sender wants to enable an option if the receiver can handle it; receiver responds that it can. Option goes into effect. Sender wants to enable an option if the receiver can handle it; receiver cannot support the option. Option does not go into effect. Sender wants the receiver to enable an option; receiver responds that it can. Option goes into effect. Sender wants the receiver to enable an option; the receiver responds that it cant. Option does not go into effect. Sender wants to disable an option. Receiver can respond only with DONT, which confirms the senders request. Sender wants the receiver to disable an option. Receiver can respond only with WONT, which confirms that it will no longer perform this option.
DO DO WONT DONT
WILL WONT DONT WONT
For example, if the sender wants to the other end to echo, it sends the following byte sequence: 255 (IAC), 251 (WILL), 1 (ECHO) The final byte of the three-byte sequence identifies the action. If the receiver can support the option, it will respond with 255 (IAC), 253 (DO), 1 (ECHO) A Telnet client server exchange basically boils down to either side (a client or server) saying to the other, I will x, which means Will you allow me to use option x? The receiver then responds either, I DO x, or I DONT x, which means either I do allow you to use option x or I dont allow you to use option x. Either way, both sides respond in symmetry for option processingthe receiving side responds with a positive or negative response to the senders request. Figures 11.4, 11.5, and 11.6 show the option negotiation process between client and server.
266
TCP/IP PRIMER PLUS
FIGURE 11.4
Note that the server (TCP port 23) is asking the client (TCP port 2921) to identify its terminal type (IAC Do Terminal-Type).
FIGURE 11.5
The client states its terminal type as Sun.
Chapter 11 TELNET
267
FIGURE 11.6
The server negotiates who will echo keystrokes and also includes the terminal type agreed upon as SunOS (Unix-based operating system).
Suboption Negotiation
Some of the negotiable option values require more information once both sides have agreed on the support of the option (either disabled or enabled). Normally the client sends and the server responds with the initial 3-byte sequence. The client and server communicate values through an exchange of value query commands and responses in the following forms: IAC (255), SB (250), (option code number), 1, IAC, SE and IAC (255), SB (250), (option code), 0, (value), IAC, SE The suboption information includes the specific value to facilitate implementation of the agreed-upon feature.
Summary
Telnet establishes a TCP connection with a remote host; it then allows you to type commands from your keyboard as if attached to the remote machines keyboard. With Telnet you can read the remote hosts output as well. The Telnet client-server relationship runs transparently, which means it gives the appearance that your keyboard and output display attaches directly to a remote host.
268
TCP/IP PRIMER PLUS
Telnet offers three basics services: Network Virtual Terminal (NVT), client and server negotiation of various options, and a symmetric view of terminals and processes. The NVT provides transparency and support for a minimum level of options between remote clients and servers used by either side. Telnet NVT provides various commands that control interactions between the client and server. Telnet incorporates these commands into the data stream. Telnet uses the first octet, known as the interpret as command (IAC) character, to indicate that the information being sent is a command. Clients and servers use option negotiation to agree on features and options to be implemented during communication. Telnet treats both sides of the connection symmetricallyeither side can request the use of an optional feature. Either side can request WILL, DO, WONT, or DONT.
Review Questions
1. What does Telnet enable a user to do? 2. What series of events have to occur to establish a Telnet session? 3. What are Telnet options used for? 4. Although there are more than 40 Telnet options, what are the 12 most important and widely used options? 5. What three basic services does Telnet offer? 6. What is the NVT and what function does it provide during Telnet operation? 7. What is the 7-bit ASCII code used for? 8. What does symmetrical connection mean? 9. What is the IAC character? 10. During option negotiation what four requests can either side ask for? 11. What six possible various responses can occur during option negotiation?
CHAPTER 12
FILE TRANSFER PROTOCOL (FTP)

FTP Session Data Representation Data Structures Transmission Modes Commands Replies
Introduction to File Transfer

RFC 959 describes one of the most popular Process/Application protocols within TCP/IP applications, File Transfer Protocol (FTP). FTP accounts for most of the file transfer on the Internet and enables a remote or local client and server to efficiently transfer files or data using TCPs reliable transport. In other words, it enables the user to transfer files between two computers; usually through the Internet. Generally speaking, you have to have an account on the remote FTP server to access files (see anonymous FTP later in this chapter). Refer to Figure 10.1 in Chapter 10, Upper-layer Protocols, to see how FTP maps to the OSI and DoD model. FTP has four objectives: Promote sharing of files (computer programs or data) Encourage indirect or implicit use of remote computers Shield a user from variations in file storage systems among hosts Transfer data reliably and efficiently FTP provides file transfer services between remote hosts. File transfer copies a complete file from system to system. With FTP you must identify yourself to the FTP server through a unique user or anonymous (if supported) account to log on and transfer files, which we explain later in this chapter. Like Telnet, FTP works between different hosts, which can run different operating systems using different file structures and even different character sets. Unlike Telnet, which uses the 7-bit ASCII NVT to achieve heterogeneity, FTP supports a limited number of file types and file structures.
270
TCP/IP PRIMER PLUS
The History of FTP

FTPs long evolution started in 1971 when Abhay Bhushan (RFC 114) developed the first transfer file mechanisms for implementation on hosts at MIT. Eric Harslem and John Heafner followed shortly thereafter with RFC 141, Comments on RFC 114 (a File Transfer Protocol). The rest of FTPs history unfolds as follows: June 23, 1971Bhushan provides RFC 172, a user-level oriented protocol for file transfer between host computers (including terminal IMPs). November 17, 1971Bhushan revises RFC 172 in RFC 265. December 8, 1971Alex McKenzie suggests further changes in RFC 281. January 25, 1972Bhushan proposes the use of set data type in RFC 294. July 8, 1972Bhushan introduces RFC 354, which makes RFCs 264 and 265 obsolete. At this point Bhushan defines FTP as a protocol for file transfer between hosts on the ARPANET, with the main function of FTP to transfer files efficiently and reliably between hosts and to allow the convenient use of remote file storage capabilities. February 16, 1973McKenzie publishes the first official FTP document in RFC 454. July 12, 1973Nancy Neigus publishes the new official FTP document in RFC 542. Although the general structure remains the same, RFC 542 reflects the considerable changes from the previous versions of FTP. 1974A barrage of comments appears in RFCs 607, 614, and 624 (and countless others). This inspires RFC 686 entitled Leaving Well Enough Alone, by Brian Harvey on May 10, 1975. June, 1980Motivated by the change from NCP to TCP, Jon Postel publishes RFC 765 as the specification of FTP for use on TCP. October, 1985Postel and Joyce Reynolds publish the current specification of FTP, RFC 959. This RFC corrects some minor documentation errors, improves the explanation of some protocol features, and adds some commands.
FTP Session
Say you need to download a new driver for your Soundblaster. You initiate this by locally executing an FTP session through your Internet browser. Typically, an FTP session involves the interaction of five software elements: User InterfaceProvides a user interface and drives the client protocol interpreter. Client PIThe client protocol interpreter. Issues commands to the remote server protocol interpreter and drives the client data transfer process. Server PIThe server protocol interpreter. Responds to commands from the Client PI and drives the server data transfer process.
Chapter 12 FILE TRANSFER PROTOCOL (FTP)
271
Client DTPClient data transfer process. Communicates with the server data process and the local file system. Server DTPServer data transfer process. Communicates with the client DTP and the remote file system. The User-FTP includes User Interface (UI) Client Protocol Interpreter (PI) Client Data Transfer Process (DTP) The Server-FTP includes Server Protocol Interpreter (PI) (control port) Server Data Transfer Process (DTP) (data port) FTP differs from other protocols in that it utilizes two separate TCP port connections: one between the PIs, the control connection and one between the DTPs, the data connection. The client and server PIs use a TCP control connection to establish and manage the FTP communication between hosts. This TCP connection establishes itself through the normal client-server manner. This TCP connection must be established before either host can transfer data. The server PI listens on well-known port number 21 for control connection requests and waits for a client communication. The client PI initiates the connection by sending a TCP SYN request (see Chapter 8, Transmission Control Protocol (TCP)) in the form of a control message addressed to the destination TCP on well-known port 21. Once both sides have established a control connection, this connection stays active for the entire time the client communicates with the server. FTP uses the connection for commands from the client to the server and for the servers responses to the client. The DTPs create a data connection every time a client and server transfer a file; this also can occur at other times (as shown later in this chapter). The client passes a data address to the well-known port 20 (designated FTP data port) on the server DTP. The client FTP side uses an internally assigned (variable) client port number. Thus, FTP uses two logical connection paths: one for control (port 21) and one for data (port 20). The control connection TCP port 21 must exist before any data exchange. When a user wants to transfer a file (send or retrieve), the user executes an FTP command to do so. This causes a second connection to open for data transfer (TCP port 20).
272
TCP/IP PRIMER PLUS
FTP can make use of the minimize delay ToS within the IP for the IP type of service because the user normally types in the commands, which is a slow process. TCP utilizes this information to set the push bit within its header, causing each hosts session to send FTP messages up the protocol stack for processing without delay. This increases the processing time during client-server exchanges.
Note
Remember an application can use IP type of service to request a router to forward traffic along a specific path based on the level of service requested. For more about ToS, please refer to Chapter 3, Network Layer/Internet Protocols.
The data connection also can use the maximize throughput ToS within the IP header to increase file transfer performance. Implementations vary by vendor; however, the result of using the appropriate qualities of services for both control and data is increased performance, which speeds the client-server negotiation and file transfers. Figure 12.1 shows a general diagram of an FTP client server relationship. Figures 12.2 and 12.3 show the two different connections between client and server as seen through a Sniffer.
FIGURE 12.1
User FTP User Interface User Server Protocol Interpreter Server Data Transfer Process FTP Commands FTP Replies File System Data Connection User Data Transfer Process File System User Protocol Interpreter
The protocol interpreter deals with the commands and replies. The user interface presents the type of interface used to the interactive user and converts these into FTP commands sent across the connection.
Internetwork Server FTP
273
FIGURE 12.2
As you can see, the client (64.0.0.57) has a variable port 2001 (within the range 1024 through 65536). Note that the push bit is set to speed the processing of information.
FIGURE 12.3
An FTP data port opens each time a file transfer is requested using TCP port 20 (well-known TCP server port for FTP data). Note the data being sent within the FTP header.
274
TCP/IP PRIMER PLUS
Data Representation
FTP has many options to resolve data representation and storage. Before data transmission between client and server, session negotiation must occur, with both sides agreeing on data representation parameters. Figure 12.4 shows a client and server negotiating the file type.
FIGURE 12.4
FTP clients and servers negotiate the file type being transferred. In this example the file type being sent is ASCII (seen in the FTP header).
There are three parameters FTP needs to decide on prior to transferring a file: Data representationIdentifies the type of data being sent Data structureSpecifies the format of the data being transferred Transmission modeSpecifies how the data transmits across the connection FTP can represent data in one of four ways: ASCII (default) EBCDIC Image file type (also called binary) Local file type In addition, ASCII and EBCDIC file types have the following format control options: Nonprint Telnet format command Fortran carriage control
275
FTP can use three types of data structure: File (default) Record Page FTP has three types of transmission modes available: Stream (default) Block Compressed The various combinations of these options add up to 72 different options. FTPs options for resolving representations and storage differences are to Provide support for every data and file type Convert files to a single network server file type Assume files share a few basic properties and support those properties The designers of FTP could have chosen a canonical (a standard that both ends must convert to) file type such as Telnets NVT; instead they assumed that they shared basic properties. Please refer to Chapter 11, Telnet, for more information about NVT.
FTP Data Types

The file type specifies the format of the data being sent. FTP transfers the text file across the data connection in NVT ASCII. This means the sender has to convert the local text file into NVT ASCII, and the receiver has to convert NVT ASCII to the local text file. The end of each line indicates a CR/LF pair (carriage return/line feed, NVT ASCII representation), which means a receiver scans every byte looking for a CR/LF pair. Figures 12.5, 12.6, 12.7, and 12.8 show the four different data types that FTP can utilize: ASCII, EBCDIC, image, and local.
FIGURE 12.5
ASCII: Default for Text Files. Y 7 1 E 7 1 S 7 1
FTP uses ASCII (8-bit characters) as its default data type for text files.
This conversion explains why Unix hosts always show more bytes transferred than the actual file size. Note that if one or both systems do not use ASCII text encoding, the data transfer processes assume the responsibility to convert between NVT ASCII and the local text file (encodings). Although FTP can utilize any of the four choices for FTP data type, you most likely encounter only ASCII and Image data types in the real world.
276
TCP/IP PRIMER PLUS
FIGURE 12.6
EBCDIC: Used for IBM Text Files. Y 8 E 8 S 8
EBCDIC (8-bit characters), which are primarily used for IBM text files, provide an alternative method of transferring text files when both ends have EBCDIC systems.
FIGURE 12.7
IMAGE: Used for exchanges between machines of the same type. 1010 110 1010 110
Image file type (8-bit characters), which are normally used for exchanges between machines of the same type and to transfer binary files, uses a contiguous stream of bits to send data.
FIGURE 12.8
LOCAL BYTE: Used for situations where the data Unit Size must be preserved. Y X E X S X
Local file type, which is used to transfer files between hosts with different byte sizes and where the data unit size must be preserved, uses a byte size defined by the local host.
Format Control
The FTP data types also have options for format control. Usually you use the format control option when text files are being transferred to printing devices. The various formats control the various ways in which vertical format information can encode within a file, including indicating the start of a page. However, only ASCII and EBCDIC file types can utilize these options: Nonprint (default)Contains no printing controls (no vertical printing information). Telnet format controlControls characters as specified in the Telnet protocol (Telnet vertical format) for the printer to interpret. Fortran carriage controlControls vertical spacing with the first character of each line (the Fortran format control character).
277
FTP Data Structures

Files can have internal structures. During transfer, the structure remains intact. The data transfer processes are responsible for mapping between transmitted structures and local structures. The different options enable FTP to work among hosts running different operating systems and using different data structures. FTP can use three different data structures: file structure, record structure and page structure.
Note
It is important to note that FTP data structures also are referred to as FTP file structures; however, in this book for claritys sake, we refer to them as data structures.
The data structure has no internal structure and transfers in a stream of contiguous bytes. FTP uses the file structure by default. The record structure, which is used only with text files, uses a file made up of sequential records. The page structure uses files made up of independent, indexed pages and is provided by the TOPS-20 operating system. The page structure is used for discontinuous files in which a file descriptor or some other associated information with the data exists. Each page transmits with a page number, which allows the receiver to store the pages in any order. Figures 12.9, 12.10, and 12.11 show the different data structures.
FIGURE 12.9
File: No internal structure; file is a continuous sequence of bytes.
This figure shows the file structure.

FIGURE 12.10
Record: File made up of sequential records.
This figure shows the record structure.
FIGURE 12.11
Page: File made up of independent, indexed pages.
This figure shows the page structure.

278
TCP/IP PRIMER PLUS
FTP Transmission Modes

The transmission mode determines how a file transmits across the data connection. There are three modes: stream, block, and compressed; although there are three transmission modes, you will most likely encounter stream mode in the real world. Stream mode, in which data is transmitted in a stream of bytes, is the default; it allows record structures. In stream mode the sender closes the data connection with an end of file for a file structure. In a record structure a special 2-byte sequence indicates the end of record and end of file. Block mode terminals utilize block mode. Block mode transmits data as a series of data blocks preceded by one or more header bytes. Compressed mode is rarely used and compression versions can vary among FTP versions. Compressed mode compresses filler (ASCII or EBCDIC files) and replicated data. It also compresses text and binary repeated values in the file (for example, a string of binary zeros). Additionally, compressed mode maximizes bandwidth. Compression varies depending on what type of file is being compressed. For example, if compress mode compresses an ASCII or EBCDIC filler, cccccccccc (10 bytes of data), into two bytes of data, there will be 2 bits to specify that it compressed the 10 bytes of replicated data; 6 bits for the binary code for 10 bytes of data (001010 = binary 10); and 8 bits for ASCII or EBCDIC files, indicated by c. For example, if compress mode compresses a binary file (space, space, space, space, or 4 bytes of data) into one byte, there will be 2 bits for specifying that it compressed the 2 bytes of filler data (bits equal 11) and 6 bits for a count filed (000100 equals binary four).
FTP Commands
The server and client protocol interpreters communicate commands and replies across the control connection as NVT ASCII (Telnet) strings. These Telnet strings start with three or four uppercase NVT ASCII characters with a CRLF at the end of each command. The client can send the server over 30 commands. These commands have three categories: access control, transfer parameter, and service. The access control commands determine which client can gain access to a specific file. Table 12.1 shows the different access control commands the server can invoke.
TABLE 12.1
HFTP Access Control Commands

Description Identifies users account. Change to parent directory on remote system. Change to working directory on remote system. Users password. Use immediately after the USER command.
String and Argument *ACCT[account-info] CDUP CWD[pathname] PASS[password]
279
TABLE 12.1
Continued
Description Quit or break the connection. Reinitialize, logout without breaking the connection. Follow with new USER command for different user. Structure mount. Gives the remote system pathname of a file system structure. Username on server.
String and Argument QUIT *REIN *SMNT[pathname] USER[username]
Commands with an asterisk in front of them indicate commands that are rarely used.
FTP uses the transfer parameter commands to change the default parameters used to transfer data on a FTP connection. Table 12.2 shows the different transfer parameter commands.
TABLE 12.2
FTP Transfer Parameter Commands

Description Transmission mode: Stream, block, or compress (parameters S, B or C). Tells the server DTP to listen on the data port for a connection. Specifies the client port number that the DTP should listen on for a connection request. File structure: File, Record, or Page (parameters F, R, or P). File type: ASCII, EBCDIC, image or local
String and Argument MODE[mode] *PASV PORT[host-port] STRU[structure] TYPE[type]
FTP uses service commands when a user requests a file transfer or file operation. The FTP servers local rules govern the pathname argument. Table 12.3 shows the various FTP server commands.
TABLE 12.3
FTP Server Commands

Description Abort previous service command and any data transfer. Allocate space for file before sending. Parameters specify number of bytes. Append file to existing file.
String and Argument ABOR *ALLO[bytes] *APPE[pathname]
280
TCP/IP PRIMER PLUS
TABLE 12.3
Continued
Description Delete file on remote system. Retrieve help information from server; for example, a list of commands supported. Sends a list of files or text over the data connection on a remote system. Make directory. Name list. Sends an entire list of the current directory of the server via the data connection. No operation. Print work directory. Shows current directory name on server. Restart transfer from server marker. Retrieve file from server. Remove directory. Rename from. Specifies the old pathname of a file to be renamed. Follow with RNTO command. Rename to. Specifies the new pathname of a file. Used with the RNFR command. Site parameters. Used by server to site specific server services. Status. Store files at the server. Store unique. Like the STOR command, except overwrites existing file. Reports operating system.
String and Argument DELE[pathname] HELP[string] LIST[pathname] MKD[pathname] NLST[pathname] NOOP PWD *REST[marker] RETR[pathname] RMD[pathname] *RNFR[pathname] *RNTO[pathname] *SITE[string] *STAT[pathname] STOR[filename] *STOU *SYST
FTP commands use the Telnet protocols requirements for all communications over the control connection. All commands with arguments have a space <SP> prior to the command. All commands end with a carriage return, line feed <CRLF> character. FTP commands that require access-control identifiers, data transfer parameters, or service request partition the commands between the <SP> and <CRLF> characters.
281
FTP Replies
FTP replies appear as three-digit numbers with an optional message in the form of text following the number string. The FTP reply format allows both the interactive user and the software to read the replies, providing information explaining the response. The software uses the three-digit numbers to determine what to do next and you can use the text, or optional message, to figure what the software intends to do next. This handy feature eliminates the need to memorize a tedious series of numerical reply strings. FTP replies guarantee synchronization of requests and actions during file transfer and ensure the user always knows the state of the server. Each command issued must generate at least one reply. Commands can appear in sequential groups, in which case the reply will show an intermediate state while processing all the commands. If a failure occurs while executing any of the commands the entire command sequence needs to be repeated. FTP replies appear with the three-digit numeric code followed by a space <SP>, the text message, and the standard end-of-line code <CRLF> to terminate the reply. Replies that exceed one line must be bracketed and a special format must be applied. For a complete explanation of multiline replies, please refer to RFC 959. The three digits of each reply have a special meaning. The first digit denotes either a positive or negative outcome has occurred. The second digit shows approximately what kind of error has occurred. Affected by the second digit, the third digit gives a finer look into what kind of error has occurred. Table 12.4 reflects the meaning of the first digit, Table 12.5 reflects the second, and Table 12.6 reflects a sampling of the third digit.
TABLE 12.4 Type 1yz 2yz 3yz 4yz 5yz
The Meaning of the First Digit of the Reply Code

Description Positive preliminary reply. Wait to send another command. Positive completion reply. Positive intermediate reply. Need to send another command. Transient negative completion reply. Command did not complete; re-issue later. Permanent negative completion reply. Cannot execute the command; do not retry.
The y represents the encoding for the second digit, the z represents the encoding for the third digit, and the x represents the encoding for the first digit.
282
TCP/IP PRIMER PLUS
TABLE 12.5 Digit x0z x1z x2z x3z x4z x5z
The Meaning of the Second Digit of the Reply Code

Description Syntax error Information Connection status Authentication and accounting Unspecified File system status
TABLE 12.6 Number 125 200 211 212 213 214 331 425 452 500 501 502
Examples of the Third Digit of the Reply Code

Description Data connection open, transfer open Command OK System busy Directory status File status Help messages for the human user User name OK, password required Unable to open data connection Error writing file Syntax error (did not recognize command) Syntax error (invalid arguments) Unimplemented MODE type
Table 12.6 gives a partial list of the reply codes for the third digit. For a complete list consult RFC 959.
FTP Operation and Examples

FTP operation starts with a human users needs. Without a human at the helmor in this case at the keyboardnone of these events can transpire. Using the Sniffer output in Figure 12.11
283
as an example, lets say you want to transfer a software program that your company has available on an FTP server: 1. You (FTP client 64.0.0.57) would execute the commands at the keyboard to set up a TCP control session with an FTP server (63.0.0.1). Note in Figure 12.11 the first three frames show the standard TCP three-way handshake with TCP port 21 as the destination. 2. Once both sides have established a connection, they exchange FTP messages. Note in frame four the server indicates it is ready to communicate. 3. The client and server go through the authentication process (frames five through eight). 4. In frame nine the client sends a RETR (retrieve) request, asking the server to get (download) a file (your software file). 5. The clients RETR command causes a TCP port 20 FTP data connection to set up (frames 1012). 6. Once both sides set up the data connection, the file negotiation takes place. 7. When the server completes the download, the data port closes (frames 15, 17, and 18). The control port remains open during the duration of the entire session between client and server. At this point you could request another file. The data port closes upon completion of the data transfer. 8. In this case you need only that software file, so you execute the quit command, terminating the entire connection as indicated by the goodbye and followed by TCP port 21 teardown (frames 1922).
FIGURE 12.12
FTP server ready to communicate (Frame 4) TCP three-way handshake (Frames 13) Authentication process (Frames 58) Data port 20 opens (Frames 1012)
FTP operation starts with a humans need. In this case FTP client 64.0.0.57 wants to get a file from FTP server 63.0.0.1.
Data port closes (Frames 15, 17, 18) TCP port 21 teardown (Frames 1922) Client sends a RETR (Frame 9)
284
TCP/IP PRIMER PLUS
Anonymous FTP
Most of the time you must have a valid user account with the FTP server with which you want to transfer files. However, some machines offer the ability to transfer files through the Internet without having a specific user account through anonymous FTP. This means you do not have to be an official user of a particular system to gain access to the files that system offers. If configured to support anonymous FTP users, servers offer an enormous amount of information to whomever wants itfrom software to cooking recipes. However, the owners of these servers can pull the plug on it anytime they want, making it no longer available to everyone through the anonymous FTP account. This would require you to get an account with that particular server. Many machines on the Internet offer Anonymous FTP. These machines allow you to log on using the user name anonymous or ftp. When the server prompts you with a password you can type your e-mail address. Most providers of these services like to know who they deal with; however, not all require you enter a password. Once the server authenticates your password you can look around and retrieve whatever files you wish. Normally, you will find all the interesting files on a directory called a pub. Providing anonymous access is a security breach and should be closely monitored. When implementing an FTP server make sure the anonymous account does not have access to sensitive company information or disable the account altogether; only allow specific user accounts with password access to the system. The last thing you want is somebody looking for a recipe for paella only to stumble upon and accidentally transfer the addresses and phone numbers of all the employees in your company or other sensitive information.
Summary
FTP allows you to transfer files between two computers usually through the Internet. FTP has four objectives: promote sharing of files, encourage indirect or implicit use of remote computers, shield a user from variations in file storage systems among hosts, and transfer data reliably and efficiently. FTP has five software elements: user interface, client PI, server PI, client DTP, and server DTP. The user FTP consists of the user interface and the client PI and DTP. The server FTP consists of the server PI and DTP. FTP differs from other protocols in that it utilizes two separate TCP network connections: one for control and one for data. FTP must decide on three parameters when transferring a file: data representation, data structure, and transmission mode. FTP represents data in one of four ways: ASCII, EBCDIC, image or local file types. FTP uses three types of data structure: file, record or page. FTP has three types of transmission modes available: stream, block, or compressed. The server and client protocol interpreters communicate commands and replies across the control connection as NVT ASCII (Telnet) strings. These Telnet strings start with three or four uppercase NVT ASCII characters with a CR and LF at the end of each command.
285
FTP replies appear as three-digit numbers with an optional message in the form of text following the number string. This format allows both the user and the software to read the replies. Replies serve to guarantee both the synchronization of requests during file transfer and that user knows the state of the server. Although some machines require that you have an account with a system to transfer files, some machines offer files through the Internet without an account through anonymous FTP.
Review Questions
1. What does FTP allow you to do and what are its four objectives? 2. What five software elements make up an FTP session? 3. What is the protocol interpreters job during an FTP session? 4. What is the job of the data transfer process during an FTP session? 5. What two TCP network connections does FTP make, and for what is each connection used? 6. What three parameters do FTP utilities use to resolve data representation? 7. In what four ways can FTP represent data types? 8. In what three ways can FTP represent data structure? 9. What three transmission modes can FTP use? 10. What three format controls does FTP use, and what data types utilize these format controls? 11. What are the characteristics of stream mode and how does it work? 12. FTP commands come in what three categories, and what do the PIs use these commands for? 13. What do FTP replies guarantee and what format do they follow? 14. What is Anonymous FTP?
CHAPTER 13
SIMPLE MAIL TRANSFER PROTOCOL (SMTP)

The X.400 Naming Model The SMTP Model and Format SMTP Commands and Replies Mail Retrieval Protocols MIME
ou could say it was the protocol that inspired a moviebut even before the Tom Hanks and Meg Ryan movie Youve Got Mail, almost everyone in the world knew what e-mail was. However, behind the scenesnot of a simplistic plotted movie but the magic of e-maillay the protocol that made it all work. Defined by RFC 821, Simple Mail Transfer Protocol (SMTP) provides the exchange of electronic mail (e-mail) between a sender (client) and receiver (server). RFC 821 works in conjunction with RFC 822, which addresses the format of these messages. SMTP uses TCP to transport messages through well-known port 25. The connection-oriented TCP helps to provide dependable delivery of these messages, but SMTP in and of itself does not provide end-to-end reliability. Like every upper-layer application that runs on top of TCP, SMTP sets up the TCP session before the transmission of data between hosts. As previously mentioned, SMTP uses a typical client/server relationship and provides a common communication channel (a TCP connection) for mail exchange between hosts. Mail exchange involves a series of request/response transactions between an SMTP client (sender) and a server (receiver). SMTP facilitates the delivery of mail messages (known as a message transfer agent or MTAs) between remote client and server mail applications (known as user agents or UAs). You dont interact with SMTP to create your e-mail. SMTP functions in the background provide mail delivery between remote hosts and require some type of front-end mail for you to interact with. Figure 13.1 illustrates the SMTP components.
288
TCP/IP PRIMER PLUS
FIGURE 13.1
Sender SMTP
Receiver SMTP
The Mail Transfer Protocol (SMTP) model.
User SenderSMTP File System
SMTP Commands/Replies and Mail
Receiver SMTP File System
The sender communicates with the receiver through a series of SMTP requests and responses that control the delivery of messages. The protocol uses the Mail from (the sender) and RCPT to (identifying the recipients) commands to exchange e-mail messages. For example, if you want to send your mother an e-mail 1. Open the mail application that links you to the SMTP client module, the UA (User Agent) on this host. 2. Compose a nice e-mail telling your mother how much you love her and so on. 3. Address it with a destination address (your mothers e-mail address). Your source address (your e-mail address) normally attaches itself to the message dynamically; if not, also enter that. 4. Press send to initiate the TCP session setup. The protocol now takes over. 5. The client opens a local TCP port for the UA and requests a TCP connection to the SMTP server (MTA). 6. Once a TCP connection is established between the UA and MTA, the receiver (Moms email account) responds with Opcode 220, which means Im ready for mail! 7. The sender (your e-mail account) issues the hello command, including its name, HELLO: Sender Name to show that the mail message is beginning. 8. The server responds with Opcode 250, which means OK, and the mail transaction begins. 9. The SMTP-client sends a Mail From command identifying the full name of the sender to the server. 10. The SMTP server verifies the Mail From contents for syntax and completeness and responds with an OK. 11. The SMTP client then sends the RCPT To command identifying the intended recipient (Mom) of the mail message to the server. 12. If the SMTP-server can accept mail for that recipient, it responds with an OK reply. If not, it replies rejecting the recipient (but not the whole mail transaction). 13. The SMTP-client and SMTP-server may negotiate several recipients. After negotiation of the recipients, the SMTP-client sends the mail data. 14. Eventually, your mom opens the e-mail and smiles at the nice message you sent her.
Chapter 13 SIMPLE MAIL TRANSFER PROTOCOL (SMTP)
289
Perhaps this is why the world loves e-mail so much. Not only did you make your mom happy by sending her such a nice e-mail; you did so without being on the phone for two hours. You also avoided all those nagging questions about when you plan to have children with quick, painless, easy communicatione-mail. Lets take a look at how an SNMP session looks through a protocol analyzer. As shown in Figure 12.2 the source host, SMTP client Atlantis, identifies itself to the SMTP server (192.42.252.1) by saying Hello. The server responds by saying Pleased to meet you. The authentication process continues with the client identifying the sender (Mail From) and the server responds by positively acknowledging the sender (sender OK). The client specifies the recipient of the message (RCPT To:); then sends the data, ending it with a period (.). The SMTP server then delivers the mail.
FIGURE 13.2
The SMTP protocol must establish a TCP connection before any delivery of e-mail can occur.
X.400 Naming Model

To better understand how SMTP works you must examine the X.400 naming model, as SMTP follows its conventions. Figure 13.3 shows a basic X.400 model through an example of e-mail exchange using TCP/IP. The user agents and message transfer agents exchange electronic mail messages. The X.400 model consists of four main components: message transfer agents (MTAs), message stores (MSs), user agents (UAs), and access units (AUs). The User Agent (UA) in the example is responsible for composing and analyzing RFC-822 message headers. Users have immediate interaction with the e-mail system through the UA. Through the UA the user composes, submits, and receives e-mail messages. The UA usually constructs the SMTP envelope at the originating site when it first queues the message for transmission by the Sender-SMTP program. Either information in the message header, supplied by
290
TCP/IP PRIMER PLUS
the user interface (for example, to implement a carbon copy [cc]), or local configuration information (for example, mailing list) determine the envelope address. The MAIL and RCPT commands transmit the envelope separately from the message itself; we discuss SMTP commands later in this chapter.
FIGURE 13.3
The user agent enables you to write, send, and receive e-mail messages.
User
User
UA P3 MTA
P2 Message Transfer System P1 MTA
UA P7 MS
MTA
UA Message Handling System
AU
X.400 Functional Model User Telex
Message Transfer Agents (MTAs)

According to 1123 SMTP server programs have similarities to X.400 MTAs. MTAs execute mail exchange and are responsible for routing e-mail messages through internetworks. These message switches connect to form the Message Transfer System (MTS). MTAs have the following functions: Accept messages by the UA or other MTAs, routing the message to the appropriate recipients UA or other MTAs en route to the ultimate destination. Analyze the recipient list in the message and perform routing decisions. Pass a message to the UA and create a delivery notification, if requested. Send messages to an MTA that indicate they need to be passed to another MTA. Generate an NDN, which is a non-delivery notification if the mail is undeliverable to a false or nonexistent address. Copy a message and delivering each copy to a different recipient for multi-addressed messages.
291
A committee of the International Telecommunications Union developed and implemented the X.400 model for the Telecommunication Unions X.400 standards CCITT (Consultative Committee for International Telegraphy and Telephony). It defines a range of protocols for addressing mail between e-mail servers including Multimedia messages (voice, graphics, fax, text) Interfacing unlike systems together Security of message transmission Reliable transport of messages Archive of messages Directory services for locating addresses Reporting delivery and receipt of messages
SMTP Format
The mail consists of the message, made up of a header and body, and the envelope, which is the SMTP source and destination address. RFC 821 specifies the contents and interpretation of the envelope. The following example shows two SMTP commands (discussed later in the chapter) that specify the envelope: MAIL From:<[email protected]> RCPT To:[email protected] RFC 822 states that the body of the message utilizes the American Standard Code for Information Interchange (ASCII) text. ASCII represents both textual data (letters, numbers, and punctuation marks) and control characters, which are commands such as return and line feed. As with other coding systems, ASCII converts information into standardized digital formats using seven-digit binary numbers. Binary numbers consist of various sequences of 0s and 1s. Computers communicate with each other, process and store data with these digital formats. NVT, using 7-bit codes for characters, transmits the 7-bit ASCII code into 8-bit octets with the most important bit set to 0. The header consists of a series of lines of text known as header fields. The majority of header fields depend on the implementation of a particular systemfew header fields are mandatory. A blank line divides the header from the body. The body of the message contains only ASCII text; the maximum line length must not exceed 1000 characters. The message also must not exceed a predefined maximum size. We will explain how to transcend these rules later in this chapter. Most systems use a variation of the following mail format example below, provided by Appendix A of RFC 822. RFC describes its example of an SMTP format as complex as youre going to get. It shows 11 fields in use, which is more than most mail systems.
292
TCP/IP PRIMER PLUS
Date : From : Subject : Sender : Reply-To : To : CC :
Comment :
In-Reply-To: X-Special-action:
Message-ID :
27 Aug 76 0932 PDT Ken Davis <[email protected]> Re: The Syntax in the RFC Ksecy@Other-Host Sam. [email protected] George Jones <[email protected]>, Al [email protected] Important folk: Tom Softwood <[email protected]>, Sam Irving@Other-Host;, Standard Distribution: /mian/davis/people/standard@Other-Host, <Jones>standard.dist.3@Tops-20-Host>; Sam is away on business. He asked me to handle His mail for him. Hell be able to provide a more accurate explanation when he returns Next week. <[email protected]>, Georgeks message This is a sample of the user-defined fieldNames. There could also a be a field-name Special-action, but its name might later be preempted 4231.629.Xyzi-What@Other-Host
SMTP Commands
SMTP commands (RFC 821) classify the mail transaction or mail system function requested by the user. SMTP commands consist of a command code and an argument (see Table 13.1). SMTP commands have some basic rules: A command code and an argument make up each SMTP command. Four alphabetic characters in either upper- or lowercase comprise the command code. One or more space characters separate this code from the argument. Because each host can have a particular rule for mail addresses, reverse path and forward path arguments are case sensitive. The character sequence carriage return-line feed (<CRLF>) concludes the argument field. Square brackets enclose optional arguments. Table 13.1 shows the standard command codes and arguments that SMTP uses.
293
TABLE 13.1
SMTP Command Codes

What It Does Identifies the sender-SMTP to receiver-SMTP. Delivers mail data to mailbox. Identifies mail data recipient. Sends the contents of the mail message. Ends existing mail transaction, causing both ends to reset. This action junks any stored information about sender, recipients, or mail data. Delivers mail to the terminals. Sends or mails. Sends or mails. Verifies that the argument identifies a user. This enables the client to ask the sender to verify a recipient address without sending mail to the recipient (usually used by a system administrator for debugging mail delivery problems). Confirms that the argument identifies a mailing list. This expands the list. Sends information. No operation. Sends OK reply; then closes channels. Exchanges Sender/Receiver roles to send mail in the opposite direction without taking down the TCP connection and creating a new one. (Sendmail does not support this command).
Command Code and Argument HELO <SP> <domain> <CRLF> MAIL <SP> FROM: <reverse path> <CRLF> RCPT <SP> TO:<forward-path> <CRLF> DATA <CRLF> RSET <CRLF>
SEND <SP> FROM:<reverse-path <CRLF> SOML <SP> FROM:<reverse-path <CRLF> SAML <SP> FROM:<reverse-path <CRLF> VRFY <SP> <string><CRLF>
EXPN <SP> <string> <CRLF> HELP [<SP> <string> <CRLF> NOOP <CRLF> QUIT <CRLF> TURN <CRLF>
<SP> represents a Space character. <CRLF> represents Carriage Return and Line Feed characters.
SMTP Replies
SMTP replies acknowledge receipt of SMTP datagrams and error notification. Replies include a three-digit number code (sent as three alphanumeric characters) followed by text. A three-digit code, <SP>, one line of text, and <CRLF> comprise a reply. The texts vary for each reply code and the various combinations indicate the purpose of the reply.
294
TCP/IP PRIMER PLUS
SMTP clients and servers use the three digits to communicate receipt of information and notify the other side when it has encountered an error. The three-digit number has a hierarchy. The first digit represents general information, and the second and third digits further define the reply, giving the receiving host enough information to determine whether an error has occurred so it can determine how to process the message. The receiver does not need to look at the message text; it only looks at the reply digits to determine whether to trash the message if there is an error or pass it on to the user. Table 13.2 demonstrates the meanings of the first digit. Table 13.3 shows the meaning of the second digit. Table 13.4 shows a numeric order list of reply codes completed by the third digit.
TABLE 13.2 First Digit 1yz 2yz 3yz 4yz 5yz
Meanings of the First Digit

Meaning Positive preliminary reply Positive completion reply Positive intermediate reply Transient negative completion reply Permanent negative completion reply
TABLE 13.3 Second Digit x0z x1z x2z x3z x4z x5z
Meanings of the Second Digit

Meaning Syntax Information Connection Unspecified as yet Unspecified as yet Mail system
TABLE 13.4 Reply Code 211 214
Numeric Order List of Reply Codes

Meaning System status or system help reply. Help message; used by the human user.
295
TABLE 13.4
Reply Code 220 <domain> 221 <domain> 250 251 354 421 <domain> 450 451 452 500 501 502 503 504 550 551 552 553 554
Continued
Meaning Service ready. Service closing transmission channel. Requested mail action okay, completed. User not localWill forward to <forward-path>. Start mail inputEnd with <CRLF>. Service not available; closing transmission channel. Can be a reply to any command if the service knows it must shut down. Requested mail action not takenMailbox unavailable (mailbox busy). Requested action abortedlocal error in processing. Requested action not takeninsufficient system storage. Syntax error, command unrecognized. This can include errors such as the command line being too long. Syntax error in parameters or arguments. Command not put into action. Bad sequence of commands. Command parameter not implemented. Requested action not takenmailbox unavailable (mailbox not found; no access). User not localplease try <forward-path>. Requested mail action abortedexceeded storage allocation. Requested action not takenmailbox name not allowed. Transaction failed.
MIME
Originating in the 80s, SMTP has always had a large user base because of its simplicity. In many cases, users have exceeded its ability, wanting to transmit messages other than text, such as a graphic, scanned photographic or video clip. SMTP simplicity causes the following restrictions:
296
TCP/IP PRIMER PLUS
The message must contain only ASCII characters. The maximum line length must not exceed 1000 characters. The message must not exceed a predefined maximum size. Multipurpose Internet Mail Extension (MIME) enhances the capabilities of standard Internet electronic mail and, more important, SMTP. Use of the MIME standard enables messages to contain additional types: Characters sets other than ASCII Multimedia: image, audio, and video messages Multiple objects in a single message Multi-font messages Messages of unlimited length Binary files The Internet Engineering Task Force Working Group defined MIME in 1992 in RFC 1521 and 1522. MIME defines the method in which files are attached to the SMTP messages. It builds on the older standard by defining additional fields for the mail message header that describe new content types and a specific message body organization. MIME extensions provide for transmissions of data previously unsupported in Internet mail by encoding the message into readable ASCII to create a standard e-mail message. Extension of SMTP protocol provides transport for new message types. RFC 1652 defines the extension for the transmission of unencoded 8-bit MIME messages. With this service extension the receiver SMTP can declare support for 8-bit body parts. The receiver also can request 8-bit transmission of a particular message. MIME resides in the 822 mail header.
Summary
Operating in the TCP/IP protocol suite, Simple Mail Transfer Protocol (SMTP) defines the format for e-mail servers to send and receive messages and for a client to send messages to a server. SMTP starts working after the client opens a TCP connection with the server on wellknown port 25. The client and server then use SMTP as a communication channel. The client sends the mail to the server through a series of carefully defined command-response transactions. The X.400 Model shows the interchange of electronic mail between User Agents and Message Transfer Agents. User Agents (UAs), also present in the SMTP Model, facilitate immediate user interaction. Through the UA the user creates, enters, and receives e-mail messages. Message Transfer Agents (MTAs), analogous to STMP programs, carry out mail exchange and communicate using NVT ASCII. X.400 defines a scope of protocols for addressing mail between e-mail servers.
297
In the SMTP format mail consists of a header, body, and envelope. The envelope consists of the SMTP source and destination address. The header consists of a series of lines of text, or fields. The header fields required depend on the conventions of a particular system. Although SMTP specifies that the body of the message should contain only limited amounts of ASCII text, Multipurpose Internet Mail Extension (MIME) transcends these rules to include non-ASCII documents, audio, video and images.
Review Questions
1. What is the main function of SMTP? 2. How do User Agents function in the SMTP model? 3. How does SMTP differ from UA? 4. Describe three of SMTPs limitations. 5. List three rules in SMTP command protocol. 6. Explain why replies are important to smooth mail transactions. 7. Why is the SMTP reply important to the user? 8. Explain how MIME functions with SMTP.
CHAPTER 14
NAME RESOLUTION

Naming Computers Namespace DNS Delegation of Authority Caching Domain Server Message Format Internet Domain Names and Their Types
Why Do We Need Name Resolution?

Back in the Stone Age of networking, users could identify and specify machines only by using long, cumbersome numeric addresses. However, internetworking brought a hierarchical IP addressing scheme, which used classful addresses (Network layer), and protocol software (such as ARP) that could change addresses back into low-level addresses. Low-level addresses (MAC address) are unique numbers that machines understand and use to forward datagrams locally on a point-to-point basis. We discussed the Network layer in Chapter 3, Network Layer/Internet Protocols, and Chapter 4, Address Resolution, and Data Link layer is addressed in Chapter 1, Overview of Industry Models and Standards. Think of each computer as a telephone. A telephone cant understand your name because it consists of letters and describes a person; not another telephones address. If your mom wants to call you on the telephone, she cant just shout out your name. A name is not enough to locate the destination or place the call. She needs to know your phone number to call you. Telephone numbers consist of a hierarchical numbering scheme identifying the area, the city, and the house of the telephone. Telecommunication switches use this information within the public switched telephone network to locate the destination and complete the call. Your computer also needs to know the Internet Protocol (IP) Address if you want it to call or reach a remote host or Web site. Like a telephone number, the IP Address (Network layer address) consists of numbers so that each computer can understand it and find the path to the destination.
300
TCP/IP PRIMER PLUS
Once the computer can identify the destination, the source and destination identify the lowerlevel address (MAC address) for point-to-point delivery through that path. Basically, the ability to use a name instead of an address is for our benefit; not the computers. When a user attempts to locate a resource using a name, devices need to resolve that name to a logical Network layer address, which in turn must be resolved to a Data Link layer address when it reaches the destination network for delivery. All this must occur before any data transmission. TCP/IP applications use DNS as a sort of telephone operator. Like a telephone operator, you can give DNS a name and get a number (IP address). This service eliminates the need for a namespace.
Namespace
Currently, the Internet consists of millions of hosts, each with its own IP address and name (if configured). To reach a host, you can use the name instead of the IP address. However, for the name to be resolved to an address you need one of two things: a DNS server (telephone operator) or a local table. Domain Name Servers provide name-toIP Address lookup services, much like a telephone operation. For instance, when you want to call Sergios Pizza, you might know the name but not the number. You have two choices: Look in your local telephone book (local table) Call 411 and have an operator help you (DNS server) Whatever method you use, you must resolve the name to the number before dialing, allowing you to complete the call and access the resourcePIZZA! How do you keep track of all these Universal and IP addresses? In the beginning, when only a few hundred hosts existed on the Internet, it was easy. A single list in the form of a text file called the namespace held all the information. The Network Information Center (NIC) kept track of the list and decided who was out or in, keeping out obscene names and names that might be confused with other names. When you wanted to participate on the Internet, you had to contact NIC to receive a copy of this list and add it to all local Internet gateways that performed the necessary resolution. Each time a name or IP address changed (added or removed from the Internet), the list changed and you had to obtain a new one. Maintaining this list and keeping up with the changes, and the local resources necessary to keep such a large list proved highly impractical. Thus, DNS emerged to address the flat, static nature of name resolution. This enables a dynamic hierarchical service to handle resolution for hosts throughout the Internet. Think of NICs namespace as your address or telephone book. You decide whos in and whos out, and insert an extra initial (or other special indicator) in case you have people on the list who share the same name. For example, if you have two people named Katie, you might name one Kate and assign one a nickname such as Kat or perhaps file them under their last names, Stevens and Pollock. You could name them Katie1 and Katie2, depending on when you met them, or by the jobs they have. Regardless of what naming scheme you decide on, there are a lot of combinations.
Chapter 14 NAME RESOLUTION
301
Note
Note that the Domain Name System (DNS) eliminates the need for the namespace by making it possible for you to find the IP address for every domain name and vice versa.
Both the namespace and your address book share a problem, especially if someone else wants to use it: clarity and usability. Because only you use the list, you understand all the personal nicknames, strange symbols, or omissions of last names on the list. Most likely, other people could not use the same list to easily find telephone numbers. They wouldnt know that you filed Katie Stevens number under just Kat and Katie Pollock under Katie. They might end up calling Katie Pollock when they wanted to call Katie Stevens. The older you get, the more people, numbers, nicknames, married couples, and business contacts get entered in the book, making the address book harder and harder for another user to differentiate telephone numbers by using just names. The namespaces local host table had the same problem. Each name on the list consisted of a string of characters without any other structure. When NIC had a small list, the small number of Internet users could understand and use it. As that list and number of users grew, they could no longer use a namelist. A namelist has the following problems: It makes expansion difficult Work overload complicates the expansion problem Its inefficient and costly Just as the number of people you know in your lifetime expands, so does the Internet. As the Internet world expanded, and new users increasingly registered computers and domain names, NIC found it impossible to keep out names that would conflict with existing names, just like an expanding address book. The list of phone numbers you need to know and what they mean (business, friends, family, doctors, and so on) increases dailyentering and organizing them can be taxing. Imagine the strain on NIC trying to organize the Internet where thousands of sites come in every day, each with hundreds of individual computers and workstations. Each time someone connected a new personal computer, NIC had to approve it. With the Internet going global and the seemingly infinite number of users, it would have been impossible, inefficient, and costly for NIC to continue to use a namelist. In the old Internet world, NIC would have had to create and maintain another list at each site every time it added a new computer name, wasting time and money.
DNS Delegation of Authority

If you had an expanding business with mounting responsibilities, you would delegate those responsibilities to other departments to ease the burden. The Domain Naming System (DNS) follows the same idea; it operates like a large, well-run corporation. When a corporation
302
TCP/IP PRIMER PLUS
grows, executives divide the responsibilities among various departments to decrease workload and maintain functionality. Each executive can hire and fire, dish out responsibilities, and further designate authority. DNS works the same way. It operates as a hierarchical tree in which the NIC governs the toplevel domains and gives the rest of the responsibilities to names servers. Table 14.1 shows the DNS root or top-level domains.
TABLE 14.1 Domain MIL GOV EDU COM NET ORG CON
Top-level Domains
Purpose U.S. Military U.S. Government Educational Commercial NICs and NOCs Nonprofit organization Two-letter country code; for example, US represents United States, UK represents United Kingdom, and so on
Proposed Top-Level Names

The seven three-character top-level domains often are referred to as generic domains. The twocharacter top-level domains (or CON domain) are based on country codes. Other top-level names have been proposed, including .firm, .shop, .web, .arts, .rec, .info, .nom, .aero, .biz, .coop, .info, .museum, .name and .pro. You may have heard about .tv, which is already a country code for the small pacific island Tuvalu. The .tv campaign has now been remarketed as a television domain by domain registrars. For more information visit http://www.icann.org.tlds.
Name servers provide resource records (RRs), which enable you to resolve, or find the IP address for a domain name and vice versa. Think of name servers as secretaries. If you want to make an appointment with your doctor you dont call your hospitals CEO; you talk directly to the receptionist. Name servers provide the same efficiency and ease. You can resolve a Domain Name without the wasted time and energy of moving through the entire DNS hierarchy. Figure 14.1 shows the hierarchical organization of DNS.
303
FIGURE 14.1
The hierarchical organization of DNS enables further delegation of addresses that are meaningful to the user.
unnamed root
top level domains
{ {
arpa
com
edu
gov
int
mil
net
org
ae
us zw
second level domains
in-addr
UCSF
United Arab Emirates
Zimbabwe
FIN
generic domains
country domains
NIC, the chief executive, maintains the top portion of the hierarchical tree (the top-level domains) partitions the Domain name that you type in to specific zones, self-governing subtrees of the DNS tree. These second-level zones also can divide into smaller zones. For example, if your site functions for a University, each zone could represent a department. If your site operates for a business, each zone could represent a location, such as a branch office or a division of responsibility (the human resources department). Using Figure 14.1 as an example, youll note that the University of San Francisco has further delegated its address to ucsf.edu. This differentiates it from the other educational sites; for example, San Francisco State University (sfsu.edu). It could further subdivide that address by department; for example, using fin.ucsf.edu to represent the financial aid department at the University of San Francisco. We will look at this hierarchical division of Internet domain names later in this chapter. Just as each division of an office needs workers to run it, so does each zone. You need a primary name server for the zone and one or more secondary name servers. The primary name server loads information from the disk files. The secondary server gets information from the primary. Like any employee, these servers need to be independent and able to fix mistakes as they happen so errors do not affect the name services for their zones. To add a new host to a zone, enter the necessary informationor at least the name and IP Addressto a disk file on the system where the primary server works. This action alerts the primary and it starts rereading its configuration files. The secondary server asks the primary server for new information about every three hours. If the secondary finds anything new, it gets it from the primary with a zone transfer. Still, these smooth-running servers dont always possess the information you request (when this occurs, the server is not considered authoritative for that information). When this happens, the server gets hold of another name server. It refers the name resolution request to that
304
TCP/IP PRIMER PLUS
server in hopes that it might resolve the name and IP address or pass it on to a name server that does possess the information that you request (considered an authoritative server). Name servers do not need to know how to reach every other name server. However, they must know the IP addresses of the root name servers. As in any office, you dont have to know every phone number to get information; you just need to know a few reliable sources. The root servers function as the phone book managers; they know the names and IP addresses of each authoritative server for all the second-level domains. After the server queries the root server, the root server tells the server to contact another authoritative server. This referral process enables a request to traverse the namespace tree until it finds a name server that knows the name (considered as authoritative for that name) and can resolve it, supplying the IP address to the requesting client.
Authoritative or Not Authoritative?

Name servers are considered authoritative when they possess the name and can resolve it. When they do not possess the name (not considered authoritative), they pass the request to another name server in hopes that it is authoritative.
DNS also can trace a domain name to a mail exchanger address and can store any kind of list of hierarchical names that you want during configuration. You can use this feature to match your business needs. For example, you can store a list of services along with the resolution from each name to the telephone number your customers would need to find out about the service. Alternatively, you could store a list of products along with the resolution of names and addresses of vendors who sell the products.
Internet Domain Names

When you look at a domain name, you first notice it consists of a series of abbreviations separated by periods. If you use the Internet heavily or if you run a site yourself, you know that the hierarchical order of these abbreviations did not come about by accident. The placement and abbreviations themselves have a purpose. Think of a 10-digit telephone number: You know the first three digits always function as the area code because the area code always comes first. If you dont put the area code first or omit it completely, you cant reach the person you are trying to call. The DNS organized the hierarchy of names so that you can quickly connect to the server to find each Web site address you type in. Lets look at how DNS divides up each domain name. DNS breaks up each section of the Domain name that represents a site or group into a section called a label or a domain; for example, Fre.devry.edu. DNS breaks up the Domain name into three domains. The lower the domain level, the more specific it gets. In this example, the lowest domain level is Fre.devry.edu, the domain name for the Fremont Campus of DeVry University. Devry.edu exists as the second-level domain, the domain name for DeVry University. Edu, the domain name educational institutions use, represents the top-level domain. If you have typed long, specific domain names, imagine these
305
names uncompressed and written in their full names. DNS uses this order to compress domain names, making them easier for you to type and organize. When you build a domain system you can choose labels for all parts of your domain name hierarchy because DNS specifies only the form of the name; not the value. However, like most of us, you just follow the labels used by the official Internet domain system. Although the system establishes order, it does so inclusively and flexibly. The system accepts all domains and lets you choose whether you want to have a geographical or an organizational naming hierarchy. Also, when you attach your TCP/IP installations to the global Internet you dont have to change names.
Queries and Mappings

DNS uses both mappings and queries to resolve the IP address from the domain name or vice versa. To help them resolve IP addresses or domain names, DNS servers keep their mapping information by saving it to disk or caching it into RAM. We discuss caching later in this chapter. You will need to understand the following terminology to understand any further discussion on DNS: Mapping and resolving both mean tracing an IP address from the domain name. Inverse mappings trace the domain name from the IP address. Inverse queries function as the commands you use to produce inverse mappings. Inverse queries usually require the server to search the entire set of servers, which is rarely used.
Caching
Like an efficient clerical worker, name servers store all of the information requests (mappings) by filing them away (saved to disk) or caching them (saved to RAM). This way, the server keeps up on the most recently requested data and has the newly requested name resolutions. Caching also lowers the cost of resolving nonlocal names because of its speed. Caching goes through different steps to resolve IP addresses: 1. When the server receives a request to resolve a name, it checks to see whether that name is part of its zone (this server is authoritative for that information). 2. If not, the server checks its cache, which holds information for about two days. 3. If it finds the information in the cache, it reports it to the client. 4. When the server gives the information to the client, it lets the client know that it got the information locally or from some other authority server (not its local table). It gives the domain name and the binding (the IP address mapped to the requested name). 5. The information could be out of date. If you want speed, just use what the server gave you. If you want accuracy, contact the authority server and verify your information.
306
TCP/IP PRIMER PLUS
Domain Server Message Format

If the server still cannot find the answer after checking its cache, it becomes a client (acting as a proxy for the source host) and uses a message format to ask multiple questions to the authoritative server in one message. Each message contains three things: A domain name to be resolved The class, or protocol family the domain name uses The type of domain name The queried server responds with answers to the questions (contained in variable fields in the message). If the server still doesnt have the answers, its reply contains information and the IP addresses for servers that might have the information. Figure 14.2 shows an example of a DNS message format. We explain each field in detail following the figure.
FIGURE 14.2
ID QDCOUNT NSCOUNT Question Section Answer Section Authority Section Additional Information Section QR OPCODE Flags RCODE
A DNS message has a fixed 12-byte header followed by four variable length fields.
ANCOUNT ARCOUNT
Identifier (ID)
The 16-bit identification field matches queries and responses. The client sets the identification; the server returns it.
QR
The 1-bit QR field identifies whether the message is a query or response. Zero (QR=0) means a query; one (QR=1) means response.
Opcode
The 4-bit Opcode field further defines the QR bit. Table 14.2 shows the various Opcodes and their meanings.
307
TABLE 14.2 Opcode 0 1 2 3-15
Opcodes
Meaning Standard query (QUERY) Inverse query (IQUERY) Server status request (STATUS) Reserved
Flags
The 7-bit flag field further describes the message. The flags field divides into five more sections (see Figure 14.3): AA (authoritative answer)Bit 5. This 1-bit flag field stands for authoritative answer, which means the name server is authoritative for the particular domain in question. TC (truncation)Bit 6. This 1-bit flag field stands for truncated, which means that the reply exceeded 512 bytes, returning only the first 512 bytes of the reply. RD (recursion desired)Bit 7. This 1-bit flag field stands for recursion desired. Set in a query and returned in a reply, this flag (when set) indicates the name server to deal with the query itselfa recursive query. However, if flag does not have the bit set and the name server does not have an AA, the name server it requested returns a list of all other name servers that have the answer to the queryan iterative query. RA (recursion available)Bit 8. This 1-bit flag field stands for recursion available. If the server supports recursion, field has a bit set to 1. Most name servers support recursion. ZeroBits 911 are always set at zero (0). Note that Figure 14.3 also shows the QR, Opcode and Rcode fields and their relationship to the flags field.
FIGURE 14.3 QR 1 opcode 4 AA TC RD RA 1 1 1 1 (zero) 3 rcode 4
Note the relationship of the other fields to the divided flags field.
Rcode
This 4-bit field stands for response code and completes the parameters of the bits 0 through 11. Table 14.3 shows the different Rcode meanings.
308
TCP/IP PRIMER PLUS
TABLE 14.3 Field 0 1 2 3 4 5 6
Rcodes
Meaning No error Format error in query Server failure Name does not exist Not implemented Refused Reserved for future use
The Rcode field completes the parameters that begin the QR field, bits 015. Table 14.4 is a quick reference of the different bits in the parameters fields. Use this table with Figure 14.2 (DNS Message Format).
TABLE 14.4
The Meaning of the Bits in the Parameter Field

Meaning Operation: 0 Query 1 Response Query Type: 0 Standard Query 1 Inverse query 2 Server status 315 reserved Set if authoritative answer (AA) Set if message truncated (TC) Set if recursion desired (RD) Set if recursion available (RA) Reserved (set to zero)
Bit Placement 0
14
5 6 7 8 911
309
TABLE 14.4
Continued
Meaning Response Type: 0 No error 1 Format error in query 2 Server failure 3 Name does not exist 4 Not implemented 5 Refused 615 reserved
Bit Placement 1215
Answers and Questions Headers

The next four 16-bit fields specify the variable length of the remaining four sections. The four fields affect each other. Table 14.5 shows these fields and their meanings.
TABLE 14.5 Field QDCOUNT ANCOUNT NSCOUNT ARCOUNT
Final Four Fields in a DNS Message

Meaning Number of Questions Entry Number of Resource Records (RRs) in the Answer section Number of Name Servers Resource Records (RRs) in the Authority section Number of Resource Records (RRs) in the Additional Records section
The number of sections are self explanatory. The client writes in only the question section of the message format. Normally, the number of questions field is 1 and the other three counts are 0. The number of answers has a count of 1 whereas the remaining two counts are 0. Normally, the question section has just one question in the field. Figure 14.4 shows the message format.
FIGURE 14.4
This shows the message format of a DNS query message.

query type
query name
query class
The question portion consists of three sections: query name, query type, and query class. Query name represents the query domain name. The query type encodes the type of question
310
TCP/IP PRIMER PLUS
(a machine name or mail address). This generates a response (called a resource record, or RR). Each response has a type, which we will discuss later. The query class field allows for Internet names to be used. The server fills in the answers section. The answers, authority, and additional information sections all are made up of RRs illustrating domain names and resolutions. Each RR illustrates one name.
Domain Name Types

Once DNS puts your name in the system, it gives it a type to show if your Domain Name functions as the address of a machine, an e-mail box, another user, and so on. This way, even though DNS lumps all of the types together, your Web site visitors can find your address easily. Table 14.6 shows the DNS RR types.
TABLE 14.6 Name A CNAME HINFO MINFO MX NS PTR SOA TXT
DNS RR Types
Description Host address Canonical name CPU and OS Mailbox information Mail exchange Name server record Pointer record Start of authority Vague text Contents 32-bit IP address Canonical domain name, used by some FTP sites as an alias for another system Name of the CPU and the Operating System Information about a mailbox or a mail list The 16-bit preference and name of the host that works as a mail exchanger for the domain Identifies authoritative name servers The IP address shown as its domain name in backward form with in-addr.arpa after it Fields defining which part of the naming hierarchy a servers uses Unintelligible string of ASCII text
DNS Examples
Lets take a look at some DNS examples as seen through a Sniffer. We will start with a host sending a query and follow this request until it is resolved. Figure 14.5 shows a host sending a query to resolve a name to an Internet address.
311
FIGURE 14.5
Note the UDP ports of the source (2798) and destination (53) indicating this request came from the DNS client going to the well-known DNS port.
Using Figure 14.5 as an example, you can see in the DNS header this is a Query to resolve the name trwind.ind.trw.com to an Internet address for a host. The client has set the recursion bit, indicating to the receiving DNS server to forward this request on to another server if it is not authoritative for this domain and cannot successfully resolve this name with local information. Figure 14.6 shows a nonauthoritative server querying another server for a client.
FIGURE 14.6
Note the DNS UDP ports of the source and destination both are 53, which means that both sending and receiving hosts are DNS servers utilizing the well-known server port.
312
TCP/IP PRIMER PLUS
Using Figure 14.6 as an example, when both the source and destination host use the same DNS UDP ports, it means that both the sending and receiving hosts are DNS servers. This happens when one DNS server is not authoritative for the information being requested and must query another server for this information on behalf of a client. The requesting server has included a unique ID number of 33628 to which the corresponding reply will match. Note that the question count is 1, which means this server has one question (piece of information). The answer count is 0 because no answer has been received yet. It also has set the authoritative bit, which means this server does not have the information necessary to answer the client query to resolve the name hart.press because it is not authoritative for the domain. This is why this server sends this query in the first place. It wants to resolve the name hart.press; the type of address it is looking to resolve to is a host address of the class type Internet. Figure 14.7 shows a server sending an error code, offering no resolution.
FIGURE 14.7
Note the ID number matches the previously sent ID within the query datagram in Figure 14.6.
Using Figures 14.6 and 14.7 as examples, note that the number IDs match in each figure. This shows DNSs correctly matching requests with responses. In Figure 4.17, note that this server is authoritative for the domain in question; however, it has no such name within the mapping table. Because it has no such name within the mapping table, the server sends an error indicated by response code 3, which offers no resolution. Figure 14.8 shows a DNS server resolving a name and mapping it to an IP address. Note the TTL value of 43200, which means that the client can assume this information is valid, cache it, and continue to use it until the timer expires, at which time the client must query again for the same information.
313
FIGURE 14.8
This is an authoritative response from a DNS server resolving the name sushi.stanford.edu and mapping it to the IP address 36.8.0.53.
NetBios
NetBIOS (Network Basic Input Output System) is an extension of BIOS (Basic Input Output System), which represents a hosts fundamental capability to access to its own local resources. IBM and Sytek extended this functionality to accessing information located on remote hosts and called it NetBIOS. Their objective was to provide a very simple way for users to access remote resources and services by using a name rather than an address. Each NetBIOS device is given a unique 15-character name; services running within the host can also have names associated with them. These unique names enable a user to find a specific service running within a host by specifying the name. In the early days of networking when IBM and Sytek introduced this protocol, no routers existed. IBMs network architecture used a flat-bridged network with all hosts belonging to the same network. IBM originally implemented NetBIOS within a hosts firmware, using a Layer 2 protocol for delivery known as NetBEUI (NetBIOS Basic Extended User Interface). NetBEUI delivers Layer 2 NetBIOS datagrams between hosts relying on source and destination MAC addresses to identify communicating hosts. Because they had no routers, this proved a successful and easy way to locate resources. NetBIOS hosts would simply send out a broadcast to all hosts on the network querying to resolve the destination hosts NetBIOS name to a MAC address. Because Layer 2 devices do not filter broadcasts, all hosts would receive this broadcast, and the host assigned this name would respond with a directed datagram to the originating source host with its MAC address. The host would complete the name resolution process once the source host had resolved the destination hosts name to MAC address, enabling the two remote hosts to exchange data through directed datagrams.
314
TCP/IP PRIMER PLUS
NetBIOS hosts send the initial query as a broadcast. The hosts then communicate, including the response that resolved the name to a MAC address, directly between hosts. Once a querying host resolves a name through NetBIOS, it stores this information in cache and retains it for a period of time in case it needs the information for future communications.
NetBIOS and NetBEUI

Many people confuse NetBIOS and NetBEUI; that confusion is understandable because they are so closely intertwined within the firmware. NetBEUI is strictly a Layer 2 protocol implementation designed to carry NetBIOS datagrams over a flat-bridged network. NetBEUI has no Layer 3 information; therefore no Layer 3 logical addressing. Because NetBEUI carries no Layer 3 logical address, you cannot route it. As a Layer 2 protocol, it limits itself to Layer 2 information and addressing (MAC addresses).
NetBIOS originally ran directly on top of this Layer 2 protocol, functionally providing a broadcast name service to hosts on the same network. You cannot route NetBEUI; however, modifications to NetBIOS have enabled it to be carried over routable protocols such as IP and IPX. This allows it to be forwarded beyond a Layer 3 boundary (across a router). NetBIOS does not limit itself to name resolution. It also manages sessions between hosts, deals with browser requests, and so on. However, for the purpose of this book, we will focus only on the name resolution functions of NetBIOS.
NetBIOS Over TCP/IP

As previously mentioned, IBM originally designed NetBIOS to run exclusively over NetBEUI in a flat-bridged network used with IBMs LAN Server and OS/2 operating systems. Microsoft adopted the protocol for use in its LAN Manager implementation, the predecessor to its popular Windows Operating system NT product line. In this earlier implementation, there were no modifications to NetBIOS or NetBEUI, making them unroutable, which limited clients to accessing only local resources. By the mid-1990s Microsoft programmers extracted NetBIOS from NetBEUI, making it portable to other protocols such as IP and IPX. By separating NetBIOS from NetBEUI, they fashioned NetBIOS as true Session layer protocol with logical APIs (Application Programming Interfaces). The logical APIs allowed NetBIOS to run over various Transport and Network layer protocols, making it routable and still maintaining the user-friendly naming service. If you have installed a Microsoft Windows client or server product, you might have noticed that you have a choice of protocols: IP, IPX, and/or NetBEUI. This choice reflects the current flexibility that allows NetBIOS to run over one or all of them simultaneously, depending on your network needs. Because this book focuses on the TCP/IP protocol suite, we will no longer discuss how NetBIOS functions over the other protocols and take a closer look at how it runs on top of TCP/IP. The Session layer protocol NetBIOS has programming hooks that enable it to port to TCP/IP, a routable protocol. However, NetBIOS uses broadcast by nature, which means that routers do
315
not forward it. This presents a problem because most networks do not exist as one flat-bridged network, but many networks separated by routers. To solve this problem, the modified NetBIOS allows it to be carried over TCP/IP well-known UDP and TCP ports 137, 138, and 139 (see Table 14.7). Although NetBIOS has other ports defined, it uses these ports primarily. RFCs 1001 and 1002 define NetBIOS over TCP/IP.
TABLE 14.7 Port Number 137 138 139
NetBIOS TCP/IP Ports

Description NetBIOS name service (NBNS). Provides name resolution. NetBIOS datagrams used for browser service. Enables hosts to announce and locate services by name. NetBIOS datagrams used for persistent net use connections. Enables hosts to connect to remote resources.
Users can access a remote hosts resources by using a UNC (universal naming convention), which consists of the computer name followed by a share name and references a path to the shared resources on a remote host. The following is an example of a UNC: \\HeathersPC\home. The UNC also can be used to create a persistent connection to a remote hosts file system, mapping a local host drive. For example, you can use the net use command to map a local drive, such as E: to Heathers home directory on Heathers PC by typing net use d:\\HeatherPC\home\heather. Once you use this command on a local host, you can access this path by simply typing d: as if it were a local path. When you use a UNC to access a resource on a remote host, this name must be resolved to a logical Network layer IP address. Once the IP address of the destination host is discovered, this address must be resolved to a local MAC address for point-to-point delivery. (We discussed address resolution in Chapter 4.) Because we already know how Network layer address resolution works, we wont discuss it in this chapter. Instead, we will focus on how NetBIOS resolves names in a TCP/IP network.
Node Types
Remember that NetBIOS has and always will use broadcasts, and routers do not pass broadcasts. When a user issues a request to access a remote host using a name, depending on the clients configuration, NetBIOS might after checking its local cache, use the following methods to resolve the name to a Network layer address: B-node (broadcast node type) Tries broadcast; then LMHosts file. Tries NBNS server only.
P-node (point-to-point node type)
316
TCP/IP PRIMER PLUS
M-node (mixed node type) H-node (hybrid node type)
Client tries b-node, p-node, then LMHosts file. Client tries p-node, b-node, then LMHosts file.
A host always looks in its local name cache first to see if it has recently resolved the requested name to an IP address. This saves bandwidth because a broadcast or directed query does not have to be sent out on the wire if one exists. If the host does not have an entry within the name cache and cannot find one by querying, it tries a node type depending on a clients configuration.
B-node
Clients check their caches first. If that fails to result in a resolution, it makes several attempts to broadcast a query out on the local segment. If it does not receive a response, as a last resort it checks (if configured) the local hosts LMHost file (LM stands for LAN Manager, which is the original Microsoft operating system implementation for clients and servers). Created by an administrator or user, this simple, local text file contains NetBIOS name-to-IP address mappings, serving the identical function as an IP host table mentioned earlier in this chapter.
P-node
P-node hosts check their caches first and then try to resolve names by sending a directed datagram to a NBNS (WINS) server, Microsofts name for a server managing name-to-IP address resolution. This node type does not generate any broadcast traffic. However, if this host has no entry in cache or in the WINS database, or the server is unavailable, the query fails. This is the most unforgiving method of resolution.
M-node
In mixed node, clients of course will try cache first. If that fails, clients will try b-node and pnode. Finally they will check the local LMHost file before giving up.
H-node
Most implementations use this as the default mode because it provides the most versatility. The order of resolution goes as follows: 1. Cache 2. P-node 3. B-node 4. LMHosts Most prefer this method because it tries a P-node before broadcasting, which increases network performance by eliminating unnecessary broadcasts from the network. Only P-node supports NetBIOS name resolution across routers. Because p-node clients must know the IP address of the NBNS (WINS) server before sending a query, they have no need to send it as a broadcast. Because it uses a directed datagram instead of a broadcast, routers can forward it.
317
So how does a client learn this address? Either an administrator configures this address on the local host or it learns this address upon boot up from a DHCP server as one of the assigned parameters. An administrator generally assigns p-node clients a primary and secondary WINS server address so if the first server is unavailable, it can try the secondary server.
WINS (Windows Internet Name Server)

Microsofts NBNS implementation is called WINS, which stands for Windows Internet Name Server. WINS basically provides dynamic NetBIOS name resolution for NetBIOS hosts, similar to a DNS server. WINS servers maintain a database of NetBIOS-to-IP address mappings. Administrators strategically place these WINS servers throughout an IP network to service name-to-address resolution requests sent by clients. An administrator can build this database manually or WINS servers can dynamically add learned names and addresses to this table. When online and configured with the IP address of a WINS server, WINS clients will register their names and addresses with this server in case some host wants to resolve the name. Upon startup, hosts that do not know what their WINS servers are will broadcast their NetBIOS names announcing their existence on the network. When this happens, a local WINS server receives the broadcast, learns the name and addressing, and enters this in its database.
WINS Proxy Agent

Most Microsoft operating system products, and some routers support name resolution by functioning as a WINS proxy agent or server for local hosts that do not have p-node capability. Clients that do not have p-node capability can broadcast resolution requests only on the local segment, which prevents them from registering and resolving names through a remote WINS server. A proxy agent is any host configured to intercept local resolution broadcast requests and relay them as directed datagrams to a remote WINS server for name resolution. When the response comes back, the relay agent caches the local request for future use and passes this information on to the source host. This enables backward compatibility with older implementations that support only b-node.
NetBIOS Examples
Lets take a look at some NetBIOS examples as seen through a Sniffer. Figure 14.9 shows a NetBIOS name service query; using it as an example, within the WINS header you can see the ID number used to match the query with the response, as shown in Figure 14.10. You might have noticed that this header and its fields are strikingly similar to the previously discussed DNS header; that is because their functions are the same. This is a query to resolve the name P60 to a WINS NetBIOS name to an Internet address.
318
TCP/IP PRIMER PLUS
FIGURE 14.9
In the UDP header note the NetBIOS name service port numbers identify the source and destination (port 137).
FIGURE 14.10
The server sends a directed datagram response to a query.
The server shown in Figure 14.10 is authoritative for the name being requested. The response has been sent as a directed datagram resolving the name to the address 161.69.97.201, verifying that this name is unique and that the clients node type is h-node (reserved node type). The requesting host will cache this information for later use. The TTL timer of 300000 seconds,
319
indicated by the WINS servers, specifies how long the source host can consider this information valid without having to return for more updated information.
Summary
In the olden days, people had to use numeric addresses instead of names for their hardware and software. Computer innovations made it possible for users to name their computers according to their locations or functions. Internetworking brought domain names and protocol software that can change these domain names back into low-level addresses. Low-level addresses consist of numbers so the computers can understand them. Before long, this simple list turned into a big burden consisting of three problems: usability, workload, and cost. The namespace was not detailed enough for new computer users to understand. The blossoming Internet caused a big headache for the NIC with thousands of new computers and workstations being connected every day. Finally, the NIC had to go around updating the namespace at each computer each time someone registered a new computer, wasting time and money. The Domain Name System (DNS) eliminates the need for the namespace by making it possible for you to find the IP address for every domain name and vice versa. The DNS divides the responsibilities of knowing this information into zones. Primary and secondary servers work at each zone. NetBIOS provides a simple way for users to access remote resources and services by using a name rather than an address. Each NetBIOS device has a unique 15-character name and services running within the host also might have names associated with them. These unique names enable a user to find a specific service running within a host by specifying the name.
Review Questions
1. Describe three problems with namespace. 2. Explain how primary servers differ from secondary servers. 3. Why cant computers understand a domain name? 4. Explain how DNS designates its authority. 5. Define the term caching and how servers use it for name resolution. 6. Why would a server use a message format? 7. List what each message must contain in a message format. 8. What is the difference between NetBIOS and NetBEUI? 9. How is NetBIOS able to do name resolution at Layer 3? 10. What are the three primary TCP/UDP ports used by NetBIOS and what are they used for?
320
TCP/IP PRIMER PLUS
11. What are the different NetBIOS node types? Briefly describe each. 12. What is a WINS proxy agent?
CHAPTER 15
HYPERTEXT TRANSFER PROTOCOL (HTTP)

HTTP Qualities HTTP Components HTTP Sessions Message Formats Error Messages Status and Error Codes HTTP Connections and Lengths
HTTP and the World Wide Web

You are babysitting your eight-year-old cousin and he really wants to see the new Disney animation flick. You open your computers home page and click the entertainment link. The entertainment Web page opens and you see the web address in the URL content window. Before the address, you notice HTTP the first bit of the URL. You find the nearest theater , showing the Disney movie and your cousin smiles joyfully when he finds out hell be seeing todays show. Every time you click a link or type in a query, you use the Hypertext Transfer Protocol (HTTP), the most widely used and recognizable protocol on the Internet. HTTP makes communication between your workstations browser and a Web server happen. Your browser works as an application program and opens Web pages. Using HTTPs features, it travels and grabs information outside the hosts operating system and hardware. Although HTTP started out helping only simple data transfer, it now supports complex data types such as the multiple graphic images you see every day on the Web.
Hyper
The term hyper in hypertext means that the document has links you can choose.
322
TCP/IP PRIMER PLUS
In this chapter we discuss the components that enable HTTP to make its journey and then go through the processes HTTP uses when you want to find a Web page. For all you computer nerds (like myself), we get into nitty-gritty detail by showing you how and why error messages occur, the various message formats, and what each part in the message means.
HTTP Features
Like a good employee, HTTP has specific qualities that set it apart. HTTP uses these qualities to make what has been commonly referred to as surfing the web, a simple and painless process. HTTPs unique characteristics include the following: It works at the Application level, providing a communication link and message forwarding; it does not offer reliability or perform retransmission. The server does not keep a history of HTTP sessions or your HTTP requests. HTTP provides bidirectional transfer, meaning the server can transfer a copy of the requested Web page to the browser and the browser can transfer to the server. It uses capability negotiation, which means browsers and servers together can figure out details such as which character set they want to use for their requests and responses. It supports caching, which means to save time, your browser caches a copy of each Web page it retrieves for you. If you want the page again, HTTP has the browser ask the server whether the contents of the present page differ from the cached copy. We will discuss caching further in Chapter 14, Name Resolution. HTTP enables support for intermediaries, which means any machine along the path between the browser and the server can be a proxy server. These proxy servers cache Web pages. They also use the cache to answer queries. We discuss proxy servers further in the following section.
HTTP Components
Just as the Beatles song says, I get by with a little help from my friends, HTTP gets by with a little help from its friendly components. This section explores all the components HTTP uses when you want to find and open a Web page. Table 15.1 describes HTTPs components.
Chapter 15 HYPERTEXT TRANSFER PROTOCOL (HTTP)
323
TABLE 15.1 Components Browser
HTTP Components
Description An independent front end existing as a Graphic User Interface (GUI) tool that changes your commands into HTTP requests and responses. The term graphic means you can see it. Work as the requests and responses that servers and browsers send back and forth to each other. Response chains usually carry the requested information. You will see these communication chains at work later in this chapter. An intermediary HTTP host working as an HTTP-enabled server, transparently enabling you to get to resources and services on behalf of the origin server. An HTTP server. Gets its name by being the first place to have the resources you want; it hosts the information. (Consider this server the hostess with the mostest.) Works as an intermediary HTTP host functioning as either an HTTP client or server so the UA and the origin server can exchange information. Proxy agents pass requests from clients to servers. Servers also respond to the request itself when the information you want is local. UAs start an HTTP session and request information for you. We will go into more detail about UAs in Chapter 13, Simple Mail Transfer Protocol (SMTP). Also referred to as method tokens. Resources are the pieces of information you want and what HTTP sessions try to get. Works as an intermediary software interface that gets transparent relay of HTTP sessions between two end host connections.
Communication chains
Gateway
Origin server
Proxy
User agents (UAs)
Resources Tunnel
Transparent or Non-transparent Proxy Agents

You can configure proxy agents transparently or nontransparently depending on requirements. Transparent proxy agents cant change client requests or server responses unless the information they pass through allows for identification and authentication of clients. However, nontransparent agents can change HTTP requests and responses to support services, such as filtering or group identification if they need to.
324
TCP/IP PRIMER PLUS
HTTP Sessions
HTTP relies on TCP at the Transport layer to provide guaranteed delivery of data using wellknown server port 80 for communication. Remember that the HTTP session begins with you, the user. An HTTP session follows these steps: 1. You open your browser and identify information or a resource you want. 2. An HTTP connection request goes out to start an HTTP session between the client (UA) and either an origin server or intermediary. 3. A Uniform Resource Identifier (URI) identifies this resource or service.
Note
HTTP may need to open several TCP sessions when receiving an HTML page, for example, for each object on the page and the HTML text itself.
When HTTP can identify a resource by name, it uses the Uniform Resource Name (URN) convention, more commonly known as the Uniform Resource Locater (URL). Here is a URL following the URN format:
http://home-movies.excite.com/
You can see that this first part of the URN identifies the protocol; in this case HTTP. The next part of the URN describes the host you are trying to reach on an origin server; for example, www.home-movies.excite.com. Additional path information follows and ends with the specific resource you request (entertainment). The origin server can service the request the UA sends. Intermediary proxy agents pass this request on as it goes to an origin server. An HTTP gateway also can service this request directly. All methods remain transparent to you; the gateway services the request even though the origin server appears to have done the job. As far as the client knows, it successfully achieves communication with and gets the requested resource on that server. Figures 15.1, 15.2, and 15.3 show three communication chains that HTTP processes can take. Figure 15.1 shows UA-to-origin server communication chain. Figure 15.2 shows a UA through an intermediary-to-origin server communication path. Note that on the way to the origin server, the request chain must go through any number of HTTP components, or intermediary devices. These devices act as communication links between the client and the server. Figure 15.3 shows a UA-to-intermediary communication path. After the client sends its request chain to the origin server, the first intermediary device sends it out, and then the second intermediary device stops it and services it. This second intermediary has information the UA requested locally, so it sends a response chain to the client with the information.
325
FIGURE 15.1
Notice how the UA communicates directly with the origin server. No intermediary HTTP hosts are needed.
FIGURE 15.2
Request Chain User Agent Single Connection Response Chain Origin Server
Proxy agents or intermediary devices pass requests from clients to servers.

FIGURE 15.3
Request Chain User Agent I1 Intermediary Connection Response Chain I2 Origin Server
A request chain can include more than one intermediary device. In this case, the second intermediary device has the information.
Request Chain User Agent I1 Intermediary Connection Response Chain I2 Origin Server
When an intermediary device handles requests, the origin servers processing time decreases, and performance and response to client requests increases. Some companies strategically place frequently requested information on intermediary devices and allow these devices to directly handle requests so that the origin servers have less work and responsibility. Intermediary devices also cache the information the client previously requested from an origin server and store this information in the hopes for a request for the same information.
HTTP Message Format

As in any protocol, the client and server communicate through a series of messages called replies and responses. We refer to HTTP messages that clients send as request claims and replies made by intermediaries or origin servers as response chains. Both message types follow a general format in this order: Generic start line, called a request line for request messages and a stats line for reply messages General header Message header One empty line Message body
326
TCP/IP PRIMER PLUS
Generic Start Line

A generic start line consists of either a request line or a status line. A UA sends a request line and an origin or gateway server indicating a response sends a status line. Generic start lines include the URI specifying the referenced resource. They function as operational indicators describing the action to be taken on the resource, and the HTTP protocol version being used, followed by a CR/LF (carriage return/line feed). Table 15.2 describes HTTP method tokens and their function.
TABLE 15.2
Method Tokens and Their Functions

Functions Requests to get resource. Tests hypertext connections. Requests to forward information. Finds the HTTP features and abilities for the UAs. Creates a new resource on the origin server, such as putting out a new message on the bulletin board. A client sends this command so the origin server will delete a resource. Helps test and diagnose errors. Proxy agents set up for tunneling use this command.
Method Tokens GET HEAD PUT OPTIONS POST DELETE Trace Connect
General Header
All message headers begin with the same general header. This applies to both request and response messages, but does not apply to the entity being transferred. HTTPs general header contains the following fields: Cache-control Connection Date Pragma Trailer Transfer-encoding Upgrade
327
Via Warning We will describe each field in the following sections.
Cache-Control
The cache-control passes the information through the request response path, controlling the caching operation of HTTP UAs, intermediaries, and origin servers. Cache control dictates: When to cache or store sent or received information How long the information should stay cached Whether the cached information remains public or private
Connection
The connection field shows HTTP clients which connection characteristic, such as persistence, it wishes to apply. These optional client connection characteristics might or might not require support from intermediary or origin servers. Proxy agents receiving client connection options can apply the characteristics to the connection or deny it, but will not pass this characteristic on to the next intermediary or origin server in the communication chain.
Date
The originator sets the date. The date field shows the date and time of the request or response.
Pragma
The pragma field defines which directions an optional set of vendors should include in the request or response chains.
Trailer
The trailer field value indicates a given set of header fields will be in the trailer of a message, encoded with chunked transfer coding.
Transfer-Encoding
The transfer-encoding field describes the method used to transfer and encode the message bodyin short, what transformation has been applied to the message to ensure safe transport through the network. Transfer-coding differs from content-coding because transfer-coding is a property of the message, not of the entity. Messages can be broken into chunks, each chunk containing its own length value, followed by an optional trailer containing entity-header fields. When users transfer large streams of information, it breaks into smaller, more manageable pieces called chunks, all belonging to the same stream. Each of these chunks must be identifiable as belonging to the stream and the length of the chunk by the recipient. Chunking allows dynamically produced material to be
328
TCP/IP PRIMER PLUS
transferred along with the information necessary for the recipient to verify that it has received the message intact (by verifying its length value). The chunked transfer-encoding method is an essential part of this field. If transfer-coding is applied to a message body, the transfer-coding must include chunked, or the connection terminates. The chunked transfer-coding must be the last transfer-coding applied to the message body and cannot be applied more than once to a message body.
Upgrade
The upgrade field settles protocol and version type to resolve compatibility issues between communicating devices.
Via
Intermediary devices such as gateways and proxies use this field. It enables these devices to keep track of forwarded messages and to identify various protocols and capabilities implemented by all devices involved in the request/reply chain.
Warning
The warning field gives an error notification.
Message Headers (Request, Response, or Entity)

The HTTP protocol operates as a request/response protocol. The client sends a request to the server and the server responds with a reply. This can generate one of three types of specific message headers: request, response, or entity.
Request Header
Within the first line a request message from a client to a server includes the method to be applied to the resource, the identifier of the resource, and the protocol version in use. A request header allows a client to send additional information about the request to the server not contained in that first line or the general header. The request header has information about the client that you are working on, the resource you ask for and the server. Table 15.3 describes what specific request headers mean.
TABLE 15.3
Request Headers and Their Meanings

Meaning Shows the character sets that are okay for the response Puts a limit on the content encoding values Puts a limit on the number of natural languages in the set Has the qualifications for a UA
Request Header Accept-Charset Accept-Encoding Accept-Language Authorization
329
TABLE 15.3
Continued
Meaning The e-mail address of whomever directs the requesting UA Internet host and port number of the requested resource Makes sure the cached info is up to date Used with a method to make it conditional Requests all or part of a unit Used with a method to make it conditional Puts a limit on the amount of proxies or gateways that can put forward a request Enables the client identify itself to a proxy Defines a resource piece The URL address from which the Request-RI was obtained Has information about the UA that started the request
Request Header From Host If-Modified-Since If-None-Match If-Range If-Unmodified-Since Max-Forwards Proxy-Authorization Range Referer UA
Response Header
Servers send a response header in response to UA requests; these messages consist of threedigit codes identifying the response type. We will discuss the response messages, three-digit status, and error codes later in this chapter.
Entity
Although optional, the entity header further defines information about the resource you request. Table 15.4 shows the meanings of the entity headers.
TABLE 15.4
Entity Headers and Their Meanings

Meaning Shows which methods the resource supports Defines the base URL Adapts the media type Explains the natural languages Specifies the extent of the body of the message in octets Gives the resource location for the unit
Entity Header Allow Content-Base Content-Encoding Content-Language Content-Length Content-Location
330
TCP/IP PRIMER PLUS
TABLE 15.4
Continued
Meaning Provides a complete message reliability check Specifies where to insert a part of the body Shows what type of media the body will have States what the tags (described later in the chapter) will be for the related entity Shows the date/time right before the response expires The last date/time the original resource underwent changes
Entity Header Content-MD5 Content-Range Content-Type ETag Expires Last-Modified
Empty line (CRLF)

This empty line takes out the end of the preceding message header.
Message Body
The body (untransparent) is everything you can see. The header messages are for the browser to read.
HTTP Response Messages, Status, and Error Codes

As in any well-running protocol, the servers give out response messages in reply to requests. Response messages let the client know exactly what is going on through a specific format encompassing certain codes and phrases. Response messages have the following format: Status Line Headers CRLF Message body The status line consists of a protocol version. The status code and the textual phrases that go with it follow the status line. HTTP status and error codes share the same three-digit format as FTP, as discussed in Chapter 12, File Transfer Protocol (FTP). These codes vary from informational to notification of a failed request. The first digit shows the general message category. The last two digits identify the message within the category. RFC 2616 states that the following message categories exist because of the last two digits:
331
1xx:Informational 2xx:Successful 3xx:Redirection
Request received, continuing process.
The action was successfully received, understood and accepted. Must take further action to complete request. Request contains bad syntax or cannot be fulfilled. Server failed to fulfill request.
4xx:Client-related error 5xx:Server-related error
Table 15.5 shows the specific meanings for each of the numeric status codes.
TABLE 15.5 Status Code 100 101 200 201 202 203 204 205 206 300 301 302 303 304 305 400 401 402 403 404
HTTP Status Codes and Their Meanings

What it Means Continue Switching protocols Okay Created Accepted Non-authoritative information No content Reset content Partial content Multiple choices Moved permanently Moved temporarily See other Not modified Use proxy Bad request Unauthorized Needs payment Prohibited Not found
332
TCP/IP PRIMER PLUS
TABLE 15.5 Status Code 405 406 407 408 409 410 411 412 413 414 415 500 501 502 503 504 505
Continued
What it Means Method not allowed Unacceptable Needs proxy authentication Requests time out Conflict Gone Needs length Precondition failed Request entity too large Request URL too large Media type not supported Internal server error Unimplemented Bad gateway Unavailable service Gateway time out HTTP version unsupported
HTTP Error Messages

During a weekend of Web surfing you probably have seen this annoying message: Bad Request Your browser sent a request that this server could not understand. After verbally stating your thoughts about this message to your computer, you might have sat back and wondered how and why this message came about. These irksome error messages appear when a Web server receives an illegal request. Usually, a browser sends this request and the browser tries unsuccessfully to show you whatever the server gives it. Therefore, the servers usually create error messages in Hypertext Markup Language (HTML).
333
HTML consists of text you can read along with embedded commands for the computer that give the rules for display. These commands, also called tags, come between less than and greater than symbols. If you do any programming, these tags should look familiar. Here is how your error message would look in the HTML format:
<HTML> <HEAD><TITLE>400 Bad Request</TITLE> </HEAD> <BODY> <H1>Bad Request</H1> Your browser sent a request that this server could not understand. </BODY> </HTML>
Only the browser uses the head of the documenteverything between <HEAD> and </HEAD>. You see only the body of the message.
Summary
Hypertext Transfer Protocol (HTTP) works as a communication link between your browser and a server when you want to find and open up Web pages. You browser works as an applications program, opening the Web pages for you. The Web page displays using Graphical User Interface (GUI) so you can see it. HTTP has specific qualities. It does not offer reliability nor does it retransmission itself. The server doesnt file away a history of HTTP sessions or your HTTP requests. HTTP supports bidirectional transfer, meaning transfer from the server to the browser and from the browser to the server. HTTP lets the browsers and servers decide which details they want to use for their requests and responses. HTTP uses caching to save time and supports intermediaries so that any machine in the path can be a proxy server. Proxy servers enable the user agent (UA) and the origin server to exchange information. The UAs request information for you; the origin server holds the information, called resources, that you want. The requests and information replies are called communication chains. HTTP sessions start when you open your browser and request information. TCP at the transport layer ensures delivery of this data. The request goes to an origin server or intermediary. A Uniform Resource Identifier (URI) identifies the resource. The name of this resource the Uniform Resource Locator (URL) follows the Uniform Resource Name (URN) convention.
334
TCP/IP PRIMER PLUS
Review Questions
1. Why do you need to use HTTP? 2. What function does HTTP have with the browser and the server? 3. What is the browsers function? 4. At which level does HTTP work and how does this affect its capabilities? 5. List three more of HTTPs qualities. 6. Explain how HTTPs support of caching adds efficiency. 7. Explain what a proxy does. 8. Which HTTP components can be a proxy? 9. State the general HTTP message format. 10. Who can read the message body? 11. Who can read the headers? 12. Why do you receive error messages?
CHAPTER 16
TRIVIAL FILE TRANSFER PROTOCOL (TFTP)

TFTP Packet Types TFTP Operation TFTP Extensions
Introduction to File Transfer Protocols

Although most people use FTP as their file transfer protocol in the TCP/IP suite (see Chapter 12, File Transfer Protocol (FTP)), not all applications need or can handle the complexity or the full functionality FTP provides. For example, FTP requires clients and servers to establish, maintain, and manage multiple TCP connections. For a PC that doesnt have a sophisticated operating system or one that has limited capacity, this might prove difficult if not impossible. In addition, FTP can be difficult to program. The TCP/IP suite provides a solution: TFTP (Trivial File Transfer Protocol). TFTP provides a simple, unsophisticated, and inexpensive file transfer service between hosts. Defined by RFC 1350, TFTP reads or writes files for a client to or from a server. Each exchange begins with a client requesting to either read or write a file from a server. TFTP offers no services other than this simple, fast file transfer; it has the distinct advantage of remaining as simple as the HulaHoop. Although initially designed to be embedded within Ethernet ROM chips of diskless clients, other data link architectures support TFTPs use. TFTPs original design transfers 512-byte blocks of data using UDP port 69, but current implementations support larger blocks. Unlike TCP and FTP, it provides no authentication and no guarantee of delivery. The sending side (TFTP client) opens a variable client UDP port (referred to as a TFTP or transfer ID), requests a file, and waits for the acknowledgement of each block before sending another block. In turn, the receiving side acknowledges each block when it receives the data.
336
TCP/IP PRIMER PLUS
TFTP does not require a ton of overhead like FTP, which uses two TCP connections (rather than connectionless UDP) to establish communication and transport data. However, because TFTP uses UDP for transport, it cannot guarantee the delivery of data. By utilizing UDP as for transport, it also makes implementing TFTP easier; hence its trivial nature and name. Because TFTP restricts itself to only simple file transfer it provides a smaller and much faster, yet reliable solution to FTP. Smaller applications can prove very important for diskless devices because TFTP can easily fit into read-only memory (ROM). When a diskless workstation powers on, it can retrieve a boot image or configuration from memory on a remote server. This allows it to obtain necessary initialization parameters remotely. TFTP provides the advantage of allowing an operating system to utilize bootstrapping code stored on a TFTP server. For example, if you turn on your computer TFTP can enable you to bootstrap from a local or remote TFTP server.
TFTP Packet Types

Similar to the protocol, TFTP keeps its operation simple. The first packet sent (by the client) requests a file transfer (from the server) and establishes the communication between the variable client UDP port (known as TID) and well-known TFTP port 69 for the server. This packet specifies a file name and whether it requests to read (RRQ), meaning to transfer from the server to the client or write (WRQ), meaning to transfer from the client to the server. TFTP accomplishes these tasks by transferring a continuous stream of datagrams in 512-byte data blocks (or larger if supported). The final block contains less than 512 bytes, or configured block size, which signifies the end of the stream. Any transmission error encountered kills the transfer. TFTP has five different packet types, described in Table 16.1; the Opcodes within the header distinguish each type.
TABLE 16.1 Opcode 1 2 3 4 5
TFTP Packet Types

Packet Type/Operation Read Request (RRQ) Write Request (WRQ) Data (DATA) Acknowledgement (ACK) Error (ERROR)
Figure 16.1 shows the different TFTP packet formats.
Chapter 16 TRIVIAL FILE TRANSFER PROTOCOL (TFTP)
337
FIGURE 16.1
The initial 2 bytes (Opcode) identify the TFTP message format. Note that RRQ and WRQ share the same packet format. The first packet sent by the client will be either an RRQ or WRQ.
Op code
Filename
Mode
string
string
octets
RRQ / WRQ Packet
Op code 2
Block Number 2 DATA Packet
Data 0 - 512 octets
Op code 2
Block Number 2 octets ACK Packet
Op code
Error Code
Err Msg
string Error Packet
octets
RRQ and WRQ Packets

As previously mentioned, RRQ and WRQ packets have the same structure. These packets begin a request and determine what file needs to be transferred. Table 16.2 describes the fields contained within the RRQ or WRQ packet.
TABLE 16.2 Field Opcode
RRQ/WRQ Packet Fields

Octets 2 Description Identifies the packet type: 1 = RRQ 2 = WRQ String of netascii, similar to ASCII, (8-bit code defined by ANSI X3.41968) characters that specify the filename. Computer sends these alphanumeric codes for human consumption.
Filename
String
338
TCP/IP PRIMER PLUS
TABLE 16.2 Field
Continued
Octets 1 String Description Terminates the filename and mode fields. Specifies transfer mode: Netascii Octet (raw 8-bit bytes) Mail (netascii characters destined for the user instead of the host); obsolete.
Zero (two fields) Mode
Data Packets
The data packets, or Type 3 packets, transfer the requested data. Table 16.3 describes the fields contained within a data packet.
TABLE 16.3 Field Opcode Block number Data
Data Packet Fields

Octets 2 2 0-512 Description Identifies the data packet with Opcode 3. Identifies the particular fixed block of data. Carries the actual information to be transferred. Any block containing less than 512 or configured block size (up to a maximum of 65,464 bytes) marks the end of the data transfer. See RFC 2348 for block size extension options.
ACK Packet
The ACK packet acknowledges the receipt of each block (data packet) received during data transfer. TFTP utilizes the lock-step acknowledgement method, which means each data packet has to be acknowledged before transmission of another. Remember TFTP transmits data one at a time in blocks, with the first data block numbered one. Because TFTP operates over UDP, it does not provide for windowing. TFTP must acknowledge all packets except error packets. ACK or error packets acknowledge data and WRQ packets, whereas data and error packets acknowledge RRQ or ACK packets. Table 16.4 describes the fields contained within an ACK packet.
339
TABLE 16.4 Field Opcode Block number
ACK Packet Fields

Octets 2 2 Description Identifies the ACK packet with Opcode 4. Corresponds to the block number of the data packet.
Error Packets
The error packet acknowledges any of the other packet types and signifies that an error has occurred. The error code appears as a number that indicates what type of error has occurred. These error messages appear for the humans benefit and appear in netascii. Most errors cause termination of the connection. Table 16.5 describes the fields contained within an error packet.
TABLE 16.5 Field Opcode Error code Error message Zero
Error Packet Fields

Octets 2 2 String 1 Description Identifies the error packet type with Opcode 5. Describes the problem using seven different error codes (see Table 16.6). Netascii string. Completes the packet.
When an error occurs the host sends an error packet, terminating the connection. Three events generate error packets: The host cannot satisfy a request (for example, cannot locate a file). The host receives a delayed or duplicated packet. When the host loses access to a resource such as a disk during the transfer. The 2-octet error code field contains a value that describes what error has occurred. Table 16.6 describes each value and its meaning.
340
TCP/IP PRIMER PLUS
TABLE 16.6 Value 0 1 2 3 4 5 6 7
Error Code Values

Description Not defined, see error message (if any) Cannot find file Access violation Disk full or allocation exceeded Illegal TFTP operation Unknown transfer ID File already exists No such user
TFTP Operation
As previously mentioned, the TFTP client initiates the connection by requesting to read or write a file from or to the server. The client does this by opening up a variable port (TFTP TID) to the receivers well-known TFTP server port 69. The client specifies the identification of the file name and data type within the initial request. Once the client sends the initial request, the TFTP server reassigns itself a new UDP port to use as its TID for the duration of this data transmission and the transfer begins. If the client makes a read request the server begins the transfer; if the client makes a write request the client begins the transmission. TFTP implements UDP at the transport layer, identifying the source and destination TIDs as port identifiers. The sender calculates a UDP checksum covering the TFTP header and data before transmission. The receiver verifies the checksum to guarantee that the bits received were not damaged during transit. The transmission continues until the client or server transfers the entire file. Figures 16.2, 16.3, and 16.4 show a TFTP client sending a write request; we will describe the request frame by frame. TFTP implements a simple sequence and acknowledgement scheme within its request/response exchange, allowing only one outstanding datagram at a time. Each time the sender transmits a datagram it holds a datagram locally for retransmission. If either side loses the datagram, the sender eventually detects this because it does not receive acknowledgement from the other side. It then times out and retransmits the buffered information.
341
FIGURE 16.2
Notice that TFTP client 128.1.0.2 (UDP port 1001 equals the TID) transmits a request to write the file junk.txt to TFTP server 128.1.0.1 (UDP port 69). The UDP header contains no sequencing information; just a simple checksum and length field.
FIGURE 16.3
The second frame contains a connectionless acknowledgement from the TFTP server, indicating its reassigned UDP port number, which is chosen randomly. This server has a new UDP port/TID of s=1487.
342
TCP/IP PRIMER PLUS
FIGURE 16.4
This frame shows the client sending the first data block within the stream.
TFTP Extensions
The original TFTP specifications have been extended to allow for option negotiation between the client and the server. Only one specific option has been defined (blocksize); however, the specification remains general enough that vendors can implement their own options as necessary. A larger blocksize increases the file transfer performance between remote hosts. Older implementation might not support this extension, which limits the transfer to the original 512-byte standard. The client side controls the option negotiation. The server side cannot request option negotiation; it can only respond to the client. If a client wishes to implement additional options beyond the normal TFTP specification, the client can append this information to its initial read or write request. TFTP servers that support option negotiation have an option acknowledgement (OACK) packet to notify the client if it supports this option. When a server accepts the option, it includes it in the OACK packet. If it does not accept the option it simply ignores it, leaving it out of the OACK frame. Clients implement only what servers allow. The client can request multiple options during the negotiation process by simply listing them within the read or write packet. The client appends the option request to the standard read or write request used to initialize the session between the client and server. For clients that support option negotiation, two additional frames appear in the header: option, which specifies the option requested, such as blocksize and value, which specifies the value for this option. For example, the expected value of blocksize ranges from 0 to 65464.
343
OACK Packet
The OACK packet uses an operation code of six. The server sends the OACK packet to reject or acknowledge options requested by the client. Table 16.7 describes the OACK packet fields. The option and value pair repeats depending on the number of options requested.
TABLE 16.7 Field Opcode Option1
OACK Packet Fields

Octets 2 2 Description Identifies the OACK packet with Opcode 6. Corresponds to the first option listed within the clients read or write request packet. Additional options list as option2, option3, and so on and correspond to the clients read or write request. Corresponds to the first option listed within the clients read or write request packet. Additional values list as value2, value3 and so on and correspond to the clients read or write request packet.
Value1
Summary
TFTP provides a simple, fast, and inexpensive file transfer service between hosts. TFTP reads or writes files for a client to or from a server. Each exchange begins with a client requesting to either read or write a file from a server. The first packet sent requests a file transfer from the server and establishes the communication between the variable client UDP port (known as TID) and well-known TFTP port 69 for the server. Original TFTP versions transfer files in 512-byte blocks although current implementations can transfer more. A block containing less than 512 bytes signifies the last block. TFTP has five packet types: RRQ, WRQ, ACK, data, and error. The RRQ or WRQ specifies a file name and whether it requests to read (RRQ) or write (WRQ) the file. Data packets transfer the requested data. ACK packets acknowledge receipt of the blocks of data. Error packets signify when an error has occurred during the transfer of the blocks of data.
Review Questions
1. What are the differences between FTP and TFTP? 2. What are some of the benefits of using TFTP? 3. What type of service does TFTP provide? 4. How does each exchange begin?
344
TCP/IP PRIMER PLUS
5. What five packets does TFTP use and what functions do they serve? 6. What does a block of less than 512 bytes signify? 7. What is the lock-step acknowledgement method and how does TFTP utilize it? 8. What three events trigger an error packet? 9. What does it mean to read a file and write a file? 10. Briefly describe TFTP operation. 11. TFTP extensions allow for option negotiation between client and server. How does this affect blocksize? 12. How does TFTP option negotiation work? 13. What is an OACK packet?
CHAPTER 17
SNMP (SIMPLE NETWORK MANAGEMENT PROTOCOL)

Network Management SNMP Managers, Agents, and Proxies SNMP Message Format
Introduction to Network Management

Actual network management might seem like a fantasy for many network managers. After all, when do they actually have time to manage their networks? Perhaps it is only after they solve all the immediate issues that threaten to make their networks toast. What is network management exactly? Some think it means eliminating problems when they occur; others think it means anticipating network problems before they ariseor at least limiting the difficulties to only minor catastrophes. Whether you take a proactive or reactive approach to network management, one protocol has stood out to address both ways of thinking: SNMP (Simple Network Management Protocol). RFC 1157 defines the original implementation of SNMP and is the main remote network management protocol in use today. Originally designed to facilitate the remote management of Internet hosts and gateways, SNMP, previously known as SGMP (Simple Gateway Management Protocol), has evolved to support a variety of end devices. The IAB (Internet Activities Board) has a major hand in the development of a vendor-neutral management protocol for managing Internet systems. Internet committees formed in the mid to late 1980s to discuss potential management protocols; three protocols emerged: HEMS SGMP High-level Entity Management Systems Renamed as SNMP Common Management Information Protocol
ISOs CMIP
346
TCP/IP PRIMER PLUS
Note
The ISO (International Organization for Standardization) is an international body that sets specific standards for network protocols. The most popular is seven-layer OSI Reference Model.
After careful consideration they deemed SGMP the short-term protocol of choice, but planned to switch to the ISO standard CMIP management protocol in the future. As previously mentioned, SGMP, now renamed to SNMP, remains the most widely used management protocol within the industry and is the official standard. SNMP provides a simple vendor-independent management solution. All of the mentioned protocols make use of management information RFCs 1065 and 1066, which describe how managed objects should be identified through the implementation of the ASN.1 (Abstract Syntax Notation 1) method of representing managed objects through arbitrary data structures. Within RFC 1156, the standard Internet MIBs (Management Information Bases), referred to as MIB I and II, identify well-known managed objects and define them within a hierarchical tree structure. All SNMP implementations must minimally support these MIBs. However, they can implement their own MIB sub-trees containing manageable objects as long as they follow the SMI (Standard Management Information) requirements defined in RFC 1156.
SNMP
SNMP runs on top of UDP, providing fast delivery of management requests and responses between hosts running SNMP-based applications, such as SunNetManager or HPs OpenView. These represent just a few of the many applications that make use of SNMP to remotely monitor and manage SNMP-enabled devices. SNMP provides delivery services of management requests and responses on behalf of the applications. It runs independent of the applications specifics, lower-layer architecture, and upperlayer applications. This makes SNMP a simple and generic, yet powerful network management protocol portable to many different platforms, operating systems, and protocols. Although SNMP historically was carried over IP, because of its generic nature it can run over other protocol suites such as IPX. SNMP has three main entities that make remote management possible: Manager Agent Proxy Command generators and notification receivers
Command responders and notification originators Forwarders
Software running within a device implements all three entities and provides SNMP messaging services to the Application level software.
Chapter 17 SNMP (SIMPLE NETWORK MANAGEMENT PROTOCOL)
347
SNMP Managers
As hosts, SNMP managers run management control software (such as OpenView) to remotely control and monitor SNMP agents. These hosts provide a central management point and user interface using SNMP to deliver commands to agents. This enables the operator to retrieve information, change configuration values, and even reboot a device. SNMP managers also receive unsolicited notification messages (known as trap messages) from agents informing them of some type of violation, such as a command received by an unauthorized SNMP manager to change a configuration value. Two examples of requests are get requests, which are used to read information and set requests, which are used to modify parameters. SNMP managers direct their requests to the destination UDP port 161 running within an agent. Managers listen for trap messages from agents on UDP port 162.
SNMP Agents
As hosts, SNMP agents run SNMP responder and notification generation software. Agents listen for SNMP requests from managers through their receiving UDP port 161. SNMP managers query agents for information, which they store in a local database referred to as an MIB (Management Information Base). Because of its small size, the agent software fits in ROM chips, which generally are included in devices as part of their firmware, such as in a transceiver port for a router or switch interface. These agents keep track of the MIB database, structured as a hierarchical tree consisting of many objects to be managed and monitored. For example, an Ethernet Interface would represent a managed object within the context of a specific agent such as a router. You could monitor this interface for specific information relating to traffic going across the interface, such as tracking the number of broadcasts, CRC error, collisions, and so on. In addition to responding to manager queries to retrieve or modify specific information, you can configure agents to alert managers. Agents alert managers by sending an unsolicited trap message when problems occur or when something attempts to violate the agent, such as a request to modify a parameter coming from an unauthorized manager. Agents send trap messages to managers addressed to UDP port 162.
MIB View
Each agent stores its collection of locally managed objects within its MIB, also referred to as the MIB view. When managers request access to an object contained within the MIB view, they must specify the object name, represented as an ASN.1 notation. The ASN.1 notation specifically describes the location of the object within the information base and the instance, the unique occurrence of the object within the managed device. A series of positive integers describing the path within the MIB tree represents the object name that identifies the location of the object. Vendors can register for their own sub-tree IDs, which enable them to extend the Internet tree to include their specific objects. IANA gives sub-tree IDs to organizations.
348
TCP/IP PRIMER PLUS
Proxy
SNMP proxies provide message forwarding between agents and managers. Proxies also act as an intermediary between agent hosts using different versions of SNMP, which enables compatibility between the hosts.
Community
SNMP agents must register with managers to start receiving requests and to know to whom and where to send notification messages. How agents identify and register with managers depends upon implementation. Agents and managers must belong to the same domain, known as a community, to facilitate the exchange of messages. There is one default domain, known as the public domain; however, you can define others on the manager and agents so that other managed communities can exist. By defining other communities, which you can name anything you like, you limit unauthorized access. If someone wants to add his or her own management host to a network to maliciously gain access to agents, first he or she would have to guess the name of the community and configure his or her manager for the same name. Of course, just creating new communities and naming them something esoteric wont prevent a clever hacker from learning this information, so authentication and access control lists protecting managed objects remains a must. SNMP does not have a function for specific authentication and access control; however, the applications that use SNMP do. If you have a proxy involved, it also must belong to the same community as the agents and manager and must register with both of them for message forwarding to begin. All entities must be locally configured with the appropriate community name and any necessary authentication and security information. Agents also need to know the Network layer address of the manager to send all responses and unsolicited notification messages.
SNMP Message Format

All SNMP messages follow the same basic structure, except the Trap message. Each request carries a version number, community name for minimal authentication, and one or more PDUs (Protocols Data Units) depending on the information being requested by the manager. Figure 17.1 shows the architecture of the SNMPv1 communication network. Figure 17.2 shows the basic format of SNMP messages.
349
FIGURE 17.1
GetResponse
GetResponse IP
Get-Next
Note that SNMP uses only five messages, part of the protocols simple approach to network management.
SNMP Management System
SNMP Managed System

Managed Resources
Management Application Get Set
Application Manages Objects Event
SNMP Managed Objects Get-Next Event
Get
SNMP SNMP Manager Messages SNMP Agent
UDP IP Link
Communications Network
FIGURE 17.2
SNMP Message Version Community GetRequest, GetNextRequest, GetResponse or SetRequest PDU
All SNMP messages (get request, get next request, get response and set request), except the trap message, use the same basic format.
PDU Type
Request ID
Error Status
Error Index
Name1: Value 1
Name 2: Value 2
Variable Buildings
Version
The version field specifies the SNMP version type being used. Both manager and agent must use the same version or the request must go through a proxy, which can translate between the two.
Community Name
This field identifies the community name. You can achieve simple authentication between managers and agents by configuring them to belong to the same community. Administrators assign community names, which are simple plain text names used to group authorized managers with agents. Agents can belong to only one community at a time. Managers can belong to multiple communities, enabling them to associate with many different agents.
Set
UDP Link
350
TCP/IP PRIMER PLUS
SNMP Protocol Data Units (PDUs)

These field identifies the type of PDU. SNMP has five mandatory PDU types: Get request Get next request Get response Set request Trap All get and set PDUs contain the following same fields (see Table 17.1). The Trap PDU has a different message format and field, which we will discuss later in this chapter.
TABLE 17.1 Field Request ID Error status
General PDU Fields

Description Each request carries a unique ID used to match with the corresponding response that the agent returns. Used to indicate whether an error was encountered. This value will always be zero for requests. If some value other than zero appears, the PDU encountered one of the following errors: 0=no error 1=PDU too big 2=no such name 3=bad value 4=read only 5=general error Specifies the type of error encountered, when error status value indicates there was an error. References specific object ID and value represented in ASN.1.
Error index Object ID and value
Trap PDUs
Trap PDUs use a different message format than the four get and set PDUs because it reports on occurrences rather than responding to a managers query. Figure 17.3 shows the trap PDU structure; Table 17.2 describes its fields.
351
FIGURE 17.3
SNMP Message Version Community Trap PDU
Note that a trap PDU uses a different structure from the other PDUs.
PDU Type
Enterprise
Agent Address
Generic Trap Type
Specific Trap Type
Timestamp Name1: Value 1 Name 2: Value 2 Variable Buildings
TABLE 17.2 Field Enterprise Agent address
Trap PDU fields

Description Identifies the object type that generated the trap. Specifies the Network layer address of the agent who originated the trap message. Specifies the reason for the trap: 0=cold start 1=warm start 2=link down 3=link up 4=authentication failure 5=EGP neighbor loss 6=enterprise specific Identifies vendor-specific trap. Indicates the time at which the agent generated the trap as a result of some event. Identifies the object ID and value for which the trap was generated.
Generic trap ID
Specific trap ID Time stamp Object Id and value
Summary
In the mid- to late 1980s Internet committees discussed potential management protocols; from those talks three protocols emerged: HEMS, CMIP, and SGMP (later renamed SNMP, or Simple Network Management Protocol). SNMP was supposed to be a short-term solution for network management but has remained the primary protocol for network management. SNMP provides delivery services of management requests and responses on behalf of the applications. It runs independent of the applications specifics, making it generic and portable to many different solutions. Its managers run management control software used to remotely control and monitor SNMP agents. Managers query agents for information. Agents run SNMP responder and notification generation software and listen for SNMP requests from managers.
352
TCP/IP PRIMER PLUS
Review Questions
1. What was SNMP previously known as? 2. What three main SNMP entities make remote management possible? 3. What are SNMP agents? 4. What are SNMP proxies? 5. What are SNMP managers? 6. What is a Trap PDU?
CHAPTER 18
OPEN NETWORK COMPUTING PROTOCOLS

ONC Protocols NFS (Network File Systems) XDR (External Data Representation) RPC (Remote Procedure Calls)
Introduction to Open Network Computing Protocols

Sun Microsystems developed the distributed file system protocol known as NFS (Network File System) and released it in 1985 as part of its ONC (Open Network Computing) family of products. The term ONC collectively describes the many protocols and services offered by Sun as a platform and independent operating system. This independence enables disparate systems to access files transparently supporting PC-to-mainframe technologies. Although NFS exists at the Application layer of the OSI model, it requires the implementation of two other protocols for functionality: XDR (External Data Representation) and RPC (Remote Procedure Calls). XDR provides Presentation layer functionality; RPC performs Session layer functionality. We will discuss all ONC protocol in more detail later this chapter. All three protocols collectively provide transparent access to distributed file systems across LAN or WAN environments and map to the DoDs Application/Process layer of the model. We start our discussion with the uppermost protocol, NFS, and move down. Figure 18.1 shows how the ONC protocols map to the OSI model.
354
TCP/IP PRIMER PLUS
FIGURE 18.1
Collectively the ONC protocol family provides transparent access to distributed file systems across LAN or WAN environments.
Application
NFS (Network File System)
NFS Information Services (Formerly YP)
Status Monitor
Lock Manager
Presentation
XDR (External Data Representation)
Session
RPC (Remote Procedure Call)
NFS Features
As the name Network File System implies, NFS provides access to information through distributed file systems over any network architecture. NFS functions as a client/server-based protocol, enabling NFS clients to access globally distributed files by sending requests to remote NFS servers. NFS supports many client operating systems (MS DOS, NetWare, Windows, NT, VMS, and so forth) and supports Data Link LAN and WAN architectures such as Ethernet, Token-Ring, X.25, Frame Relay and so on (see Table 18.2). Implementations involve client and server software programs (NFS); a data representation interpreter (XDR), which provides operating system independence; and a communication protocol (RPC), which provides the link between them passing requests and responses. The current version, NFS version 3, has replaced version 2; Sun never released version 1. Sun originally developed NFS and its components to run on top of UDP at the Transport layer; however, NFS can run on top of TCP. Although NFS is strictly implemented over the TCP/IP protocol suite currently, it is not limited to the TCP/IP protocol suite and may be carried over any other protocol suite in the future. Table 18.1 lists the various NFS version 2 and 3 features.
TABLE 18.1 Feature
NFS Versions 2 and 3 Features

V2 Yes Yes Yes Yes Yes V3 Yes Yes Yes Yes Yes Benefit Global file systems remain accessible and transparent to users. Network can easily grow as a company grows. Eliminates tedious administrative tasks. Users and application can move easily throughout the network. Supports low-cost client system.
Automatic mounting Scalability Centralized administration Shared file system namespace Supports diskless, dataless, and autoclient configurations
Chapter 18 OPEN NETWORK COMPUTING PROTOCOLS
355
TABLE 18.1 Feature
Continued
V2 Yes Yes Yes N/A Yes Yes Yes No No No Yes V3 Yes Yes Yes N/A Yes Yes Yes Yes Yes Yes Yes Yes Yes Benefit Meets particular security needs by having a wide choice of security mechanisms. DES, Kerberos, Unix Style. ACLS, Unix Style N/A Provides efficient data transport over WAN/LAN. Fast access to remote files. Increases cache space, increases performance. Improves client write throughput. Increases scalability and overall performance. Can access multi-gigabyte files on NFS servers. Replica can replace a server if it goes down. Able to handle system or network failures. Increased scalability and performance.
Flexible security architecture Multiple authentication flavors Multiple authorization flavors Dual v1 and v2 support NFS TCP Performance improvements Local disk caching Asynchronous Reduced attributes requests 64 bit sizes and offset support Read-only replica server support
Highly available NFS server (optional) Yes Reduced requests for directory lookup information No
Table 18.2 shows a list of vendors and OS platforms.
TABLE 18.2 Vendor Amdahl Apple
Multi-Vendor NFS Products

OS Platform UTS A/UX DOS, Windows Unix UNICOS Ultrix, VMS SVR4 DOS, Windows, OS/2
Beame and Whiteside BSDI Cray DEC Dell FTP Software
356
TCP/IP PRIMER PLUS
TABLE 18.2 Vendor
Continued
OS Platform DOS, Windows HP-UX AIX, MVS Unix Unix DOS, Windows TOS 35 Netware OSF1 SCO Unix Solaris, DOS, Windows IRIX VMS NeWs TI SVR3.2 VMS
Frontier Technology Hewlett-Packard IBM Intel ICL Net Manage Nixdorf Novell OSF Santa Cruz Operation Sunsoft Silicon Graphics Process Software Sony Texas Instruments TGV
NFS Operation
At the center of the model are geographically distributed file servers (NFS servers), which provide client access to shared information (see Figure 18.2). NFS servers provide shared access to file systems through a process known as exporting. Shared server directories are known and referred to as exported file systems. Using the export command, server administrators must define which parts of the file system stored on the server are eligible for export to clients. Once an administrator has defined the export areas, NFS clients can use the mount command to logically attach to the servers export area, linking the remote file system structure to a locally defined area on the client, known as the mount point. This process enables the user to access the remote file system as if it were local. Figure 18.2 shows an example of the basic components required to share and access files between clients and servers.
357
FIGURE 18.2
Use the mount command to tell the Unix kernel that a new filesystem should be attached to the file at a specified mount point.
Client
Mount a remote file system. It appears as if it were local. Export Mount Point
Server
1 3
1 3 5 7
2 Mount 5 6
6 7
Transparent Network Operations in the form of Server Procedures
NFS Client
The software needed to participate in file sharing depends on the type of operating system and system architecture. Each client requires an NFS program to make mounting and unmounting requests. Mounting enables the remote shared export area to be incorporated into the local clients file system, referred to as the client tree. Unmounting, the opposite of mounting, enables a client to release a previously mounted file system, releasing the associated resources and detaching the export area from the local trees mount point. The mount point is the point within the clients local tree. It defines where the mounted file system attaches. An enhanced mount tool, referred to as the automounter, enables the automatic mounting and dismounting of exported file systems based on configured mapping information. The automounter works just like the manual mount command that links a remote export area to a point in the clients local file system (mount point). However, the process occurs dynamically based on predefined mappings. The concept of mounting a remote file system and making it appear local is not new and should not seem foreign to you if you have worked with any other operating systems, such as NetWare or any Microsoft Windows product. With these operating systems you refer to mounting as mapping. To access a resource on a remote host, you simply use an unused local drive letter, such as E:, F:, and so on, and create a mapping to a directory within a remote hosts file system. After you perform this task, simply access the remote area by typing in the letter you used to map to the remote resource. The drive letter represents our local mount point and the client subsequently uses it to refer to the remote area. Think of mapping as a shortcut. If each time you needed to access a remote resource you had to build a complete path to the server and the subdirectory to gain access, it would consume an unbelievable amount of time, slowing down access to remote resources. By creating a map, you pave a direct path to the resources and simply refer to it each time you want to access it.
358
TCP/IP PRIMER PLUS
A user-friendly name can identify the local mount point such as: /home/heather. Or, it can simply use a local drive letter (E:, F:, and so on). The export area on the server to be mounted (exported file system) can lie anywhere within the servers file structure, containing multiple sublevel directories and files, such as NFSServ:/export/homedir/heather. Once the client has performed a local mount, it links the remote file system structure to the local mount point. Collectively, mount points form a namespace. The user can now access any information stored within the exported file system simply by referring to the client name /home/heather or the drive letter representing the remote area, such as f:. Figure 18.3 shows an example of the automounter maps and the NFS namespace.
FIGURE 18.3
/home/heather NFSServ:/export/homedir/heather
NFS clients gain access to files from NFS servers by mounting the servers exported file system. NFS clients need a map to the servers file system.
If you no longer need access to a resource, you can simply unmap (or unmount) the exported file system. To save time you can create local mapping configuration files, which the automounter will use to dynamically mount and unmount exported file systems when necessary, enabling you to tie up resources only when needed.
NFS Server
NFS servers contain distributed file systems that can be shared by defining export areas (exported file systems) through the export command within the share program. NFS servers respond to NFS client requests for shared information. An administrator must create an export configuration file and define the following: What files you want to be shared Who can access the shared area Any restrictions relating to accessing this area and its information The complete pathname specifying the directories to be exported A list of NFS clients allowed to access the exported areas A list of specific restrictions relating to access the information within the area
359
When an NFS server initializes, its share program uses the information contained within the export configuration file to establish export capabilities and identify exportable file systems. Two operating system processes, mount-d and nfs-d (d means daemon) support clients requests for access to the servers file system.
Automounter Components and Operation

As previously mentioned, the automounter is an enhanced mount tool. It enables the automatic mounting and dismounting of exported file systems based on configured mapping information. The automount process uses three main components: Automount command Automount-d (daemon) Autofs (automount virtual file system)
Autocommand
Upon system boot the autocommand initializes. After initialization, it opens and references the auto_master (configuration mapping file), which stores the local pathnames (mount points) to exported file system mappings. It uses this information to build a local mount table on the host. Once it builds the local mount table, a user can access the file system by using the cd command. When a user attempts to access a local mount point, the autofs (auto file system), which represents the local placeholder (virtual file system) for the file system the client wishes to access, invokes the automount daemon to retrieve the requested file system and mount it. The automount-d on the client sets up a communication path with the nfs-d on the server to export the remote file system. Once the client has mounted the remote file system, the automounter and its components have finished their responsibilities, and it is unnecessary to facilitate continual file access.
XDR
A component within NFS, XDR makes NFS portable across various operating system platforms. Developed by Sun Microsystems, the Internet has since adopted and included it in RFC 1014. Primarily XDR provides platform independence. NFS client and server programs can run on drastically different operating systems and hardware, from Macintosh to Unix hosts, yet still share files transparently. XDR provides this capability by hiding the specific operating system internals from each side, translating machine-specific information before transmission or after reception. XDR provides a standard library of programming routines written in C programming language, which enables vendors to implement it within their own environments representing data in a machine-independent fashion. Figure 18.4 show how XDR provides machine-independent functionality.
360
TCP/IP PRIMER PLUS
FIGURE 18.4
portable data
XDR translates and presents data so that two different operating systems can communicate with each other.
Translate to XDR standard representations
Translate to operating system representations
The byte order, the representation of floatingpoint integers, character encoding, etc., are defined using this machine's operating system
The byte order, the representation of floatingpoint integers, character encoding, etc., are defined using this machine's operating system
How data is storedthe specific byte order, memory addresses, and so onis important only to the local hosts XDR process. XDR has a bidirectional logical link between NFS and RPC. When the NFS program on a host generates information for transmission, it gives this to XDR for processing before passing it down to RPC for Session layer management. In reception mode, XDR receives NFS messages from RPC, and interprets and translates this information into a format this hosts operating system can understand. Remember the discussion regarding Presentation layer protocols in Chapters 1 and 10: The presentation layers job is to present data in a format consistent with the hosts operating system and machinespecific requirements, performing translation, encryption, decryption, conversion from ASCII to EBCDIC and reverse, and so on. The Presentation layers functions generally are included within the programming of most upper-layer protocols and not separately defined as is the case with XDR. Sun Microsystems defined a separate protocol within its suite to enable vendors to more efficiently and specifically alter the functionality within their XDR implementations. XDR facilitates communication with disparate hosts, enabling programmers to specifically tailor the protocols to their operating systems needs, making portability to other operating systems easier. Although defined as a separate protocol, XDR performs an integral part of the upper-layer protocols functionality and as such cannot be seen within the Sniffer output.
RPC
Sun Microsystems also developed RPC (Remote Procedure Calls); the Internet adopted it as RFC 1057. RPC offers a protocol and independent interface capable of providing a bidirectional communication link between remote communicating processes. It resides at the Session
361
layer; thus it has the responsibility of setting up a session between two host processes, and maintaining and tracking the session. When the hosts no longer need the logical session, RPC tears down the session and releases local resources. Remote Procedure Calls describes RPCs function. Think in terms of a local process running on a host and how it makes requests for information; this is a Local Procedure Call (LPC). Now consider the fact that the local host is requesting a procedure to be performed by a remote host and expects that host to process the request and send a response; this is a function of RPC. Figure 18.5 shows the relationship between LPC and RPC.
FIGURE 18.5
Local Procedure Calls Remote Procedure Calls
Computer A Main Program Main Program Computer B
Hosts make procedure calls that look local when actually a remote machine executes them.
Procedure A ( )
Procedure A ( )
Procedure A (waits )
RPC Call RPC Call
Procedure A ( )
Procedure B ( )
Procedure B ( )
Procedure B (waits )
RPC Call RPC Call
Procedure B ( )
Hosts running RPC use it to send remote procedure calls such as read, write, print and so on to a destination host, which processes the request and responds through RPC with a positive or negative result. RPC remains unaware of the operating system running on the local host and remote host, and relies on upper layers such as XDR to interpret the machine-specific information carried within the message request or response. Think of RPC as a facilitator that simply and generically carries the specific request from an upper-layer protocol, making sure it was sent and received. RPC typically runs on top of UDP for fast delivery; however, because of its generic nature it can run on top of TCP for additional reliability. RPC has such generic makeup in its operation that it has since been ported to other operating systems and protocol environments, such as Microsofts NT platform.
Call Message
Each remote procedure has an active client side that sends a call message to the server, which returns a reply message. The network consists of one or more remote programs. The following sections describe the RPC header and fields within a call (request) message. An RPC call message has the following fields:
362
TCP/IP PRIMER PLUS
Transaction ID
The transmitter assigns an ID number. RPC uses this field to match calls and replies.
Type
The type field identifies the RPC message type as either a call or reply: 0 = Call 1 = Reply
Version
The version field identifies the RPC protocol version in use. The version number should always be 2.
Program
The program field identifies the upper-layer application program that is using RPC, such as NFS. Table 18.3 lists programs that have registered RPC values and can run on top of RPC.
TABLE 18.3 RPC Number 100000 100001 100002 100003 100004 100005 100006 100007 100008 100009 100010 100011 100012 100013 100014
Registered RPC Programs

Program PMAPPROG RSTATPROG RUSERSPROG NFSPROG YPPROG MOUNTPROG DBXPROG YBINDPROG WALLPROG YPPASSWDPROG ETHERSTATPROG QQUOTAPROG SPRAYPROG IBM3270PROG IBMRJEPROG Description Portmapper Remote stats Remote users NFS Yellow Pages Mount daemon Remote DBX YP binder Shutdown message YP Password password server Ethernet Stats Disk quotas Spray packets 3270 mapper RJE mapper
363
TABLE 18.3 RPC Number 100015 100016 100017 100018 100019 100020 100021 100022 100023 100024 100025 100026 100027 100028 100029 100030 100031 100032 100033 100034 100035 100036 100037 100038 100039 150001 200000 200001
Continued
Program SELNSVCPROG RDATABASEPROG REXECPROG ALICEPROG SCHEDPROG LOCKPROG NETLOCKPROG X.25PROG STATMON1PROG STATMON2PROG SELNLIBROG BOOTPARAMPROG MAZEPROG YPUPDATEPROG KEYSERVEPROG SECURECMDPROG NETFWDIPROG NETFWDTPROG SUNLINKMAP_PROG NETMONPROG DBASEPROG PWDAUTHPROG TFSPROG NSEPROG NSE_ACTIVATE_PROG PCNFSDPROG PYRAMIDLOCKINGPROG PYRAMIDSYS5 Description Selection service Remote database access Remote execution Alice office automation Scheduling service Local lock manager Network lock manager X.25 INR Protocol Status monitor 1 Status monitor 2 Selection library Boot parameters service Mazeware game UP update Key server Secure login NFS net forwarder init NFS net forwarder trans Sunlink MAP Network monitor Lightweight database Password authentication Translucent file service NSE server NSE activate daemon PC password authorization Pyramid-locking Pyramid-sys5
364
TCP/IP PRIMER PLUS
TABLE 18.3 RPC Number 200002 300001
Continued
Program CADDS_IMAGE ADT_RFLOCKPROG Description CV cadds_image ADT file locking
Procedure
The field identifies the application-specific procedure number. This value varies depending on the procedure being requested and the application requesting the procedure. Consult your vendor documentation for specific procedure numbers. Table 18.4 lists the NFS server procedures.
TABLE 18.4
NFS Server Procedures

Procedure Name Do nothing Get file attributes Set file attributes Get filesystem root Look up file name Read from symbolic link Read from file Write to cache Write to file Create file Remove file Rename file Create link to file Create symbolic link Procedure Functionality Allows server response testing and timing Allows client to determine a server files attributes Allows client to set (some of) a server files attributes Obsolete Allows client to perform a directory look-up on a file Allows client to read data from a file pointed to by a symbolic link Allows client to read data from a file Used with NFS Version 3 only. Allows client to write data in a server file Allows client to create a new file on a server Allows client to remove a file from a server Allows client to rename a file on a server Allows client to create a file that links to another file Allows client to create a file that is a symbolic link
Procedure Number 0 1 2 3 4 5 6 7 8 9 10 11 12 13
365
TABLE 18.4
Continued
Procedure Name Create directory Remove directory Read from directory Get filesystem attributes Procedure Functionality Allows a client to create a directory on a server Allows a client to remove a directory on a server Allows client to read some entries in a server directory Allows client to inspect the attributes of a server
Procedure Number 14 15 16 17
Table 18.5 lists the mount server procedures.
TABLE 18.5
Mount Server Procedures

Procedure Name Do nothing Add mount entry Return mount entries Remove mount entry Remove all mount entries Return export list Procedure Functionality Allows server response testing and timing Adds another filesystem to the list of remote filesystems a client has access to Allows a client to look at its list of mounted filesystems Deletes a filesystem from the list of remote filesystems a client has access to Deletes all filesystems from the list of remote filesystems a client has access to Allows a client to look at the list of remote filesystems that a specific server offers
Procedure Number 0 1 2 3 4 5
Authentication Type
The authentication type identifies the authentication indicator. This value specifies whether authentication is being requested and if so, which type: 0 = Null (none) 1 = Unix (Unix authentication) 2 = Short (Vendor-specific authentication) 3 = DES (data encryption standard)
366
TCP/IP PRIMER PLUS
Authentication Byte Size

The authentication byte size field identifies the number of bytes of authentication that will follow.
Authentication Data
The authentication data field has a variable length and includes authentication specific information.
Authentication Verification
The authentication verification field specifies the authentication method the receiver is expected to use to verify this call or reply. Communicating hosts must support the same authentication type: 0 = Null (None) 1 = Unix (Unix authentication) 2 = Short (vendor-specific authentication) 3 = DES (data encryption standard authentication)
Reply Message
As previously mentioned, each remote procedure call has an active client that sends a call to the server, which returns a reply. A call message can take on one of two forms: it can be either rejected or accepted. The following sections describe the RPC header and fields within a Reply (response) message. Only two fields within the reply differ from the call message: Status Accept status
Status
The status field identifies whether the server accepted or denied the previously sent call. Two values appear in this field: 0 = Accepted 1 = Denied
Accept Status
The accept status field further describes the meaning of the accepted or denied status indicator. The following accept status values exist: 0 = Success 1 = Program unavailable
367
2 = Program version mismatch 3 = Procedure unavailable 4 = Garbage arguments to procedure
NFS Examples
There are many different types of NFS procedures; therefore, each NFS header varies depending on the call or reply. Figure 18.6 shows a read a file request procedure (type 6). Note that the procedure type is 6 for read a file request. The file handle, which is the long numerical number following this field, identifies the specific file on the remote host.
FIGURE 18.6
Note that NFS uses a client/server paradigm where a local client that runs the application can have access to files from a server that manages the file or application program.
Note in Figure 18.6 that the offset value of 4096 bytes refers to the starting point within the requested file at which the read request should begin. This means the request should start reading at 4906 bytes within the file; count 4096 means read 4906 bytes total. Figure 18.7 shows an NFS response to a previous read request, procedure type 6 (read a file). Notice the NFS server verifies the client's user ID and Group ID information, and permissions associated with each to ensure the user has the appropriate permission to perform the procedure requested. The user and group permissions allow rw (read and write) privileges. Figure 18.8 shows an example of an RPC call. In this figure, first look at the UDP destination port identifying RPC as port 2049. Now look in the RPC header: RPC will use the transaction ID to match to a corresponding reply when it receives it. The type of RPC message being sent is a call. The registered program value for NFS is 100003; version type is 2. The authentication
368
TCP/IP PRIMER PLUS
type is Unix. Note the machine name is being passed (Mafalda) along with the user IDs (UIDs) and group IDs (GIDs) to enable the receiver to authenticate and verify this request before processing.
FIGURE 18.7
With NFS a client, regardless of location of the client or server, can have transparent access to files.
FIGURE 18.8
NFS enables users, regardless of which operating system they use, to share directories and files.
369
Summary
NFS initiates a request or responds to a request to perform a read, write, copy, rename and so on. NFS prepares this request or response operation for transmission, and then it hands this procedural call or response to XDR for interpretation and encoding translation. XDR passes this information to RPC, which is responsible for setting up and maintaining a session between the two hosts.
Questions
1. What are the three protocols in the ONC family? 2. What is the primary function of NFS? 3. What is the primary function of XDR? 4. What is the primary function of RPC? 5. What company developed the ONC protocols?
APPENDIX A
RFCS ORGANIZED BY CHAPTER
Chapter 1: Overview of Industry Models and Standards

1095 CommonManagement Information Services and Protocol Over TCP/IP(CMOT). U.S. Warrier and L. Besaw. (April 1989) (Format: TXT=157506 bytes) 1180 TCP/IP Tutorial. T. J. Socolofsky and C. J. Kale. (January 1991) (Format: TXT=65494 bytes) (Status: INFORMATIONAL) 1195 Use of OSI IS-IS for Routing in TCP/IP and Dual Environments. R. W. Callon. (December 1990) (Format: TXT=187866, PS=362052 bytes) (Status: PROPOSED STANDARD)
Chapter 2: IP Addressing
1219 On the Assignment of Subnet Numbers. P. F Tsuchiya. (April 1991) (Format: . TXT=30609 bytes) (Status: INFORMATIONAL)
Chapter 3: Network Layer/Internet Protocols

760 Internet Protocol 777 Internet Control Message Protocol 781 Specification of the Internet Protocol (IP) Timestamp Option 791 Internet Protocol 792 Internet Control Message Protocol 815 IP Datagram Reassembly Algorithms 1011 Official Internet Protocols. J.K. Reynolds and J. Postel. (June 1987) (Format: TXT=129194 bytes) (Status: INFORMATIONAL) (Obsoletes RFC0991) (Status: UNKNOWN)
372
TCP/IP PRIMER PLUS
1016 Something a Host Could Do With Source Quench. The Source Quench Introduced Delay (SquID). W. Prue, J. Postel. (July 1987) (Format: TXT=47922 bytes) (Status: UNKNOWN) 1018 Some Comments on SquID. A.M. McKenzie. (August 1987) (Format: TXT=7931 bytes) (Status: UNKNOWN) 1025 TCP and IP Bake Off. J. Postel. (September 1987) (Format: TXT=21297 bytes) (Status: UNKNOWN) 1027 Using ARP to Implement Transparent Subnet Gateways. S. Carl-Mitchell and J. S. Quarterman. (October 1987) (Format: TXT=82440 bytes) (Status: HISTORIC) 1051 Standard for the Transmission of IP datagrams and ARP Packets Over ARCNET Networks. P. A. Prindville. Mar-01-1988. (Format: TXT=7779 bytes) (Obsoleted by RFC1201, std0046) (Status: UNKNOWN) 1054 Host Extensions for IP Multicasting. S. E. Deering. May-01-1988. (Format: TXT=45465 bytes) (Obsoletes RFC0988) (Obsoleted by RFC1112) (Status: UNKNOWN) 1055 Nonstandard for Transmission of IP Datagrams Over Series l Lines: SLIP. J.L. Romkey. Jun-01-1988. (Format: TXT=12911 bytes) (Status: STANDARD) 1063 Path MTU Discovery Options. J. C. Mogul, C. A. Kent, C. Partridge, and K. McCloghrie. Jul-01-1988. (Format: TXT=27121 bytes) (Obsoleted by RFC119) (Status: UNKNOWN) 1071 Computing the Internet Checksum. R. T. Braden, D. A. Borman, and C. Partridge. Sep01-1988. (Format: TXT=54941 bytes) (Updated by RFC1141) (Status: UNKNOWN) 1077 Critical Issues in High-bandwidth Networking. B. M. Leiner. Nov-01-1988. (Format: TXT=116464 bytes) (Status: UNKNOWN) 1141 Computation of the Internet Checksum via Incremental Update. T. Mallory and A. Kullberg. Jan-01-1990. (Format: TXT=3587 bytes) (Updates RFC1071) (Updated by RFC1624) (Status: INFORMATIONAL) 1188 Proposed Standard for the Transmission of IP Datagrams Over FDDI Networks. D. Katz. Oct-01-1990. (Format: TXT=2242 bytes) (Obsoletes RFC1103) (Status: DRAFT STANDARD) 1191 Path MTU DiscOvery. J. C. Mogul, S. E. Deering. Nov-01-1990. (Format: TXT=47936 bytes) (Obsoletes RFC1063) (Status: DRAFT STANDARD) 1208 Glossary of Networking Terms. O. J. Jacobsen and D. C. Lynch. Mar-01-1991. (Format: TXT=41156 bytes) (Status: INFORMATIONAL) 1256 ICMP Router Discovery Messages. S. Deering. Sep-01-1991. (Format: TXT=43059 bytes) (Also RFC0792) (Status: PROPOSED STANDARD) 1413 Identification Protocol. M. St. Johns. January 1993. (Format: TXT=16291 bytes) (Obsoletes RFC931) (Status: PROPOSED STANDARD)
Appendix A RFCS ORGANIZED BY CHAPTER
373
1624 Computation of the Internet Checksum via Incremental Update. A. Rijsinghani, Editor. May 1994. (Format: TXT=9836 bytes) (Updates RFC1141) (Status: INFORMATIONAL) 1788 ICMP Domain Name Messages. W. Simpson. April 1995. (Format: TXT=11722 bytes) (Status: EXPERIMENTAL) 2002 IP Mobility Support. C. Perkins. October 1996. (Format: TXT=193103 bytes) (Updated by RFC2290) (Status: PROPOSED STANDARD) 2005 Applicability Statement for IP Mobility Support. J.Solomon. October 1996. (Format: TXT=10509 bytes) (Status: PROPOSED STANDARD) 2041 Mobile Network Tracing. B. Noble, G. Nguyen, M. Satyanarayanan, and R. Katz. December 1996. (Format: TXT=64688 bytes) (Status: INFOMRATIONAL) 2058 Microsoft Vendor-specific RADIUS Attributes. C. Rigney, A. Rubens, W. Simpson, S. Willens. January 1997. (Format: TXT=118880 bytes) (Obsoleted by RFC2138) (Status: PROPOSED STANDARD) 2059 RADIUS Accounting. C. Rigney. January 1997. (Format: TXT=44237 bytes) (Obsoleted by RFC2139) (Status: INFORMATIONAL) 2113 IP Router Alert Option. D. Katz. February 1997. (Format: TXT=7924 bytes) (Status: PROPOSED STANDARD) 2138 Microsoft Vendor-specific RADIUS attributes. C. Rigney, A. Rubens, W. Simpson, S. Willens. April 1997. (Format: TXT=12407 bytes) (Obsoletes RFC2058) (Status: PROPOSED STANDARD) 2139 RADIUS Accounting. C. Rigney. April 1997. (Format: TXT=44919 bytes) (Obsoletes RFC2059) (Status: INFORMATIONAL) 2194 Review of Roaming Implementations. B. Aboba, J. Lu, J. Ding. W. Wang. September 1997. (Format: TXT=81533 bytes) (Status: INFORMATIONAL) 2290 Mobile-IPv4 Configuration Option for PPP IPCP. J. Solomon and S. Glass. February 1998. (Format: TXT=39421 bytes) (Updates RFC2002) (Status: PROPOSED STANDARD) 2344 Reverse Tunneling for Mobile IP. G. Montenegro. May 1998. (Format: TXT=39468 bytes) (Status: PROPOSED STANDARD) 2356 Suns SKIP Firewall Traversal for Mobile IP. G. Montenegro and V. Gupta. June 1998. (Format: TXT=53198 bytes) (Status: INFORMATIONAL) 2477 Criteria for Evaluating Roaming Protocols. B. Aboba and G. Zorn. December 1998. (Format: TXT=23530 bytes) (Status: INFORMATIONAL) 2486 The Network Access Identifier. B. Aboba and M. Beadles. January 1999. (Format: TXT=14261 bytes) (Status: PROPOSED STANDARD)
374
TCP/IP PRIMER PLUS
2501 Mobile Ad hoc Networking (MANET): Routing Protocol Performance Issues and Evaluation Considerations. S. Corson and J. Macker. January 1999. (Format: TXT=28912 bytes) (Status: INFORMATIONAL) 2521 ICMP Security Failures Messages. P. Karn and W. Simpson. March 1999. (Format: TXT=14637 bytes) (Status: EXPERIMENTAL) 2548 Microsoft Vendorspecific RADIUS Attributes. G. Zorn. March 1999. (Format: TXT=80763 bytes) (Status: INFORMATIONAL) 2607 Proxy Chaining and Policy Implementation in Roaming
Chapter 4: Address Resolution

826 Ethernet Address Resolution Protocol: On Converting Network Protocol Addresses to 48-bit Ethernet Address for Transmission on Ethernet Hardware 903 Reverse Address Resolution Protocol 925 Multi-LAN Address Resolution 1027 Using ARP to Implement Transparent Subnet Gateways. S. Carl-Mitchell and J. S. Quarterman. Oct-01-1987. (Format: TXT=21297 bytes) (Status: UNKNOWN) 1029 More Fault-tolerant Approach to Address Resolution for a Multi-LAN System of Ethernets. G.Parr. May-01-1988. (Format: TXT=44019 bytes) (Status: UNKNOWN) 1107 Plan for Internet Directory Services. K. R. Sollins. Jul-01-1989. (Format: TXT=51773 bytes) (Status: INFORMATIONAL) 1112 Host Extensions for IP multicasting. S. E. Deering. Aug-01-1989. (Format: TXT=39904 bytes) (Obsoletes RFC0988, RFC1054) (Updated by RFC2236) (Status: STANDARD) 1293 Inverse Address Resolution Protocol. T. Bradley and C. Brown. January 1992. (Format: TXT=11368 bytes) (Obsoleted by RFC2390) (Status: PROPOSED STANDARD) 1329 Thoughts On Address Resolution for Dual MAC FDDI Networks. P. Kuehn. May 1992. (Format: TXT=58150 bytes) (Status: INFORMATIONAL) 1433 Directed ARP. J. Garrett, J. Hagen, and J. Wong. March 1993. (Format: TXT=41028 bytes) (Status: EXPERIMENTAL) 1868 ARP Extension-UNARP. G. Malkin. November 1995. (Format: TXT=7681 bytes) (Status: EXPERIMENTAL) 1931 Dynamic RARP Extensions for Automatic Network Address Acquisition. D. Brownell. April 1996. (Format: TXT=47005 bytes) (Status: PROPOSED STANDARD) 2390 Inverse Address Resolution Protocol. T. Bradley and C. Brown, A. Malis. August 1998. (Format: TXT=20849 bytes) (Obsoletes RFC1293) (Status: PROPOSED STANDARD)
375
Chapter 5: IP Routing
917 Toward An Internet Standard Scheme For Subnetting 932 Toward An Internet Standard Scheme For Subnetting 936 Toward An Internet Standard Scheme For Subnetting 940 Toward an Internet Standard Scheme For Subnetting 950 Internet Standard Subnetting Procedure 1042 Standard for Transmission of IP datagrams Over IEEE 802 Networks. J. Postel and J. K. Reynolds. Feb-01-1988. (Format: TXT=34359 bytes) (Obsoletes RFC0948) (Status: STANDARD) 1136 Administrative Domains and Routing Domains: A Model for Routing in the Internet. S. Hares and D. Katz. Dec-01-1989. (Format: TXT=22158 bytes) (Status: INFORMATIONAL) 1219 On the Assignment of Subnet Numbers. P. F Tsuchiaya. Apr-01-1991. (Format: . TXT=30609 bytes) (Status: INFORMATIONAL) 1234 Tunneling IPX Traffic Through IP Networks. D. Provan. Jun-01-1991. (Format: TXT=12333 bytes) (Status: PROPOSED STANDARD) 1335 A Two-tier Address Structure for the Internet: A Solution to the Problem of Address Space Exhaustion. Z. Wang and J. Crowcroft. May 1992. (Format: TXT=15418 bytes) (Status: INFORMATIONAL) 1347 TCP and UDP with Bigger Addresses (TUBA), A Simple Proposal for Internet Addressing and Routing. R. Callon. June 1992. (Format: TXT=26563, PS=42398 bytes) (Status: INFORMATIONAL) 1365 An IP Address Extension Proposal. K. Siyan. September 1992. (Format: TXT=12790 bytes) (Status: INFORMATIONAL) 1366 Guidelines for Management of IP Address Space. E. Gerich. October 1992. (Format: TXT=17793 bytes) (Obsoleted by RFC1466) (Status: INFORMATIONAL) 1375 Suggestion for New Classes of IP Addresses. P. Robinson. October 1992. (Format: TXT=16990 bytes) (Status: INFORMATIONAL) 1385 EIP: The Extended Internet Protocol. Z. Wang. November 1992. (Format: TXT=39123 bytes) (Status: INFORMATIONAL) 1454 Comparison of Proposals for the Next Version of IP. T. Dixon. May 1993. (Format: TXT=35064 bytes) (Status: INFORMATIONAL) 1466 Guidelines for Management of IP Address Space. E. Gerich. May 1993. (Format: TXT=22262 bytes) (Obsoletes RFC1366) (Status: INFORMATIONAL)
376
TCP/IP PRIMER PLUS
1475 TP/IX: The Next Internet. R. Ullmann. June 1993. (Format: TXT=77854 bytes) (Status: EXPERIMENTAL) 1526 Assignment of System Identifiers for TUBA/CLNP Hosts. D. Piscitello. September 1993. (Format: TXT=16848 bytes) (Status: INFORMATIONAL) 1550 IP: Next Generation (IPng) White Paper Solicitation. S. Bradner and A. Mankin. December 1993. (Format: TXT=12472 bytes) (Status: INFORMATIONAL) 1597 Address Allocation for Private Internets. Y. Rekhter, B. Moskowitz, D. Karrenberg, and G. de Groot. March 1994. (Format: TXT=17430 bytes) (Obsoleted by BCP0005, RFC1918) (Status: INFORMATIONAL) 1621 Pip Near-term Architecture. P. Francis. May 1994. (Format: TXT=128905 bytes) (Status: INFORMATIONAL) 1622 Pip Header Processing. P. Francis. May 1994. (Format: TXT=34837 bytes) (Status: INFORMATIONAL) 1627 Network 10 Considered Harmful (Some Practices Shouldnt be Codified). E. Lear, E. Fair, D. Crocker, and T. Kessler. June 1994. (Format: TXT=18823 bytes) (Obsoleted by BCP0005, RFC1918) (Status: INFORMATIONAL) 1667 Modeling and Simulation Requirements for IPng. S. Symington, D. Wood, and M. Pullen. August 1994. (Format: TXT=17291 bytes) (Status: INFORMATIONAL) 1668 Unified Routing Requirements for IPng. D. Estrin, T. Li, and Y. Rekhter. August 1994. (Format: TXT=5106 bytes) (Status: INFORMATIONAL) 1669 Market Viability as a IPng Criteria. J. Curran. August 1994. (Format: TXT=8099 bytes) (Status: INFORMATIONAL) 1670 Input to IPng Engineering Considerations. D. Heagerty. August 1994. (Format: TXT=5350 bytes) (Status: INFORMATIONAL) 1671 IPng White Paper on Transition and Other Considerations. B. Carpenter. August 1994. (Format: TXT=17631 bytes) (Status: INFORMATIONAL) 1672 Accounting Requirements for IPng. N. Brownlee. August 1994. (Format: TXT=6184 bytes) (Status: INFORMATIONAL) 1673 Electrical Power Research Institute Comments on IPng. R. Skelton. August 1994. (Format: TXT=7476 bytes) (Status: INFORMATIONAL) 1674 A Cellular Industry View of IPng. M. Taylor. August 1994. (Format: TXT=6157 bytes) (Status: INFORMATIONAL) 1675 Security Concerns for IPng. S. Bellovin. August 1994. (Format: TXT=8290 bytes) (Status: INFORMATIONAL) 1676 INFN Requirements for IPng. A Ghiselli, D. Salomoni, and C. Vistoli. August 1994. (Format: TXT=8493 bytes) (Status: INFORMATIONAL)
377
1677 Tactical Radio Frequency Communication Requirements for IPng. B. Adamson. August 1994. (Format: TXT=24065 bytes) (Status: INFORMATIONAL) 1678 IPng Requirements of Large Corporate Networks. E. Britton and J. Tavs. August 1994. (Format: TXT=18650 bytes) (Status: INFORMATIONAL) 1679 HPN Working Group Input to the IPng Requirements Solicitation. D. Green, P. Irey, D. Marlow, and K. ODonoghue. August 1994. (Format: TXT=17846 bytes) (Status: INFORMATIONAL) 1680 IPng Support for ATM Services. C. Brazdziunas. August 1994. (Format: TXT=17846 bytes) (Status: INFORMATIONAL) 1681 On Many Addresses per Host. S. Bellovin. August 1994. (Format: TXT=11964 bytes) (Status: INFORMATIONAL) 1682 IPng BSD Host Implementation Analysis. J. Bound. August 1994. (Format: TXT=22295 bytes) (Status: INFORMATIONAL) 1683 Multiprotocol Interoperability In IPng. R. Clark, M. Ammar, and K. Calvert. August 1994. (Format: TXT=28201 bytes) (Status: INFORMATIONAL) 1686 IPng Requirements: A Cable Television Industry Viewpoint. M. Vecchi. August 1994. (Format: TXT=39052 bytes) (Status: INFORMATIONAL) 1687 A Large Corporate Users View of IPng. E. Fleischman. August 1994. (Format: TXT=34120 bytes) (Status: INFORMATIONAL) 1688 IPng Mobility Considerations. W. Simpson. August 1994. (Format: TXT=19151 bytes) (Status: INFORMATIONAL) 1705 Six Virtual Inches to the Left: The Problem With IPng. R. Carlson, and D. Ficarella. October 1994. (Format: TXT=65222 bytes) (Status: INFORMATIONAL) 1707 CATNIP: Common Architecture for the Internet. M. McGOvern and R. Ullmann. October 1994. (Format: TXT=37568 bytes) (Status: INFORMATIONAL) 1710 Simple Internet Protocol Plus White Paper. R. Hinden. October 1994. (Format: TXT=56910 bytes) (Status: INFORMATIONAL) 1715 The H Ratio for Addresses per Host. C. Huitema. November 1994. (Format: TXT=7392 bytes) (Status: INFORMATIONAL) 1719 A Direction for IPng. P. Gross. December 1994. (Format: TXT=11118 bytes) (Status: INFORMATIONAL) 1726 Technical Criteria for Choosing IP The Next Generation (IPng). C. Partridge and F Kastenhoz. December 1994. (Format: TXT=74109 bytes) (Status: INFORMATIONAL) . 1744 Observations on the Management of the Internet Address Space. G. Huston. December 1994. (Format: TXT=43675 bytes) (Status: PROPOSED STANDARD)
378
TCP/IP PRIMER PLUS
1752 The Recommendation for the IP Next Generation Protocol. S. Bradner and A. Mankin. January 1995. (Format: TXT=127784 bytes) (Status: PROPOSED STANDARD) 1753 IPng Technical Requirements Of the Nimrod Routing and Addressing Architecture. N. Chiappa. December 1994. (Format: TXT=46586 bytes) (Status: INFORMATIONAL) 1797 Class A Subnet Experiment. Internet Assigned Numbers Authority (IANA). April 1995. (Format: TXT=6779 bytes) (Status: EXPERIMENTAL) 1809 Using the Flow Label Field in IPv6. C. Partridge. June 1995. (Format: TXT=13591 bytes) (Status: INFORMATIONAL) 1814 Unique Addresses Are Good. E. Gerich. June 1995. (Format: TXT=5936 bytes) (Status: INFORMATIONAL) 1860 Variable Length Subnet Table for IPv4. T. Pummill and B. Manning. October 1995. (Format: TXT=5694 bytes) (Obsoleted by RFC1878) (Status: INFORMATIONAL) 1878 Variable Length Subnet Table for IPv4. T. Pummill and B. Manning. December 1995. (Format: TXT=19414 bytes) (Obsoletes RFC1860) (Status: INFORMATIONAL) 1879 Class A Subnet Experiment Results and Recommendations. B. Manning. January 1996. (Format: TXT=10589 bytes) (Status: INFORMATIONAL) 1880 IPv6 Address Allocation Management. IAB&IESG. December 1995. (Format: TXT=3215 bytes) (Status: INFORMATIONAL) 1883 Internet Protocol, Version 6 (IPv6) Specification. S. Deering and R. Hinden. December 1995. (Format: TXT82089 bytes) (Status: PROPOSED STANDARD) 1884 IP Version 6 Addressing Architecture. R. Hinden and S. Deering, Editors. December 1995. (Format: TXT=37860 bytes) (Obsoleted by RFC2373) (Status: PROPOSED STANDARD) 1885 Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6). A. Contra and S. Deering. December 1995. (Format: TXT=32214 bytes) (Status: PROPOSED STANDARD) 1886 DNS Extensions to support IP version 6. S. Thomson and C. Huitema. December 1995. (Format: TXT=6424 bytes) (Status: PROPOSED STANDARD) 1887 An Architecture for IPv6 Unicast Address Allocation. Y. Rekhter and T. Li, Editors. December 1995. (Format: TXT=66066 bytes) (Status: INFORMATIONAL) 1888 OSI NSAPs and IPv6. J. Bound, B. Carpenter, D. Harrington, J. Houldsworth, and A. Lloyd. August 1996. (Format: TXT=36469 bytes) (Status: EXPERIMENTAL) 1897 IPv6 Testing Address Allocation. R. Hinden and J. Postel. January 1997. (Format: TXT=6643 bytes) (Status: EXPERIMENTAL) 1900 Renumbering Needs Work. B. Carpenter and Y. Rekhter. February 1996. (Format: TXT=9528 bytes) (Status: INFORMATIONAL)
379
1916 Enterprise Renumbering: Experience and Information Solicitations. H. Berkowitz, P. Ferguson, W. Leland, and P. Nesser. February 1996. (Format: TXT=16117 bytes) (Status: INFORMATIONAL) 1918 Address Allocation for Private Internets. Y. Rekhter, B. Moskowitz, D. Karrenberg, G. J. de Groot, and E. Lear. February 1996. (Format: TXT=22270 bytes) (Obsoletes RFC1627, RFC1597) (Also BCP0005) (Status: BEST CURRENT PRACTICES) 1933 Transition Mechanism for IPv6 Hosts and Routers. R. Gilligan and E. Nordmark. April 1996. (Format: TXT=47005 bytes) (Status: PROPOSED STANDARD) 1955 New Scheme for Internet Routing and Addressing (ENCAPS) for IPNG. R. Hinden. June 1996. (Format: TXT=10115 bytes) (Status: INFORMATIONAL) 1970 Neighbor Discovery for IP Version 6(IPv6). T. Narten, E. Nordmark, and W. Simpson. August 1996. (Format: TXT=197632 bytes) (Status: PROPOSED STANDARD) 1971 IPv6 Stateless Address Autoconfiguration. S. Thomson and T. Narten. August 1996. (Format: TXT=61210 bytes) (Obsoletes RFC1971) (Status: DRAFT STANDARD) 1972 Transmission of IPv6 Packets Over Ethernet Networks. M. Crawford. August 1996. (Format: TXT=6353 bytes) (Status: PROPOSED STANDARD) 1981 Path MTU DiscOvery for IP version 6. J. McCann, S. Deering, and J. Mogul. August 1996. (Format: TXT=56890 bytes) (Status: PROPOSED STANDARD) 2008 Implications of Various Address Allocation Policies for Internet Routing. Y. Rekhter and T. Li. October 1996. (Format: TXT=34717 bytes) (Also BCP0007) (Status: BEST CURRENT PRACTICES) 2019 Transmission of IPv6 Packets Over FDDI Networks. M. Crawford. October 1996. (Format: TXT=12344 bytes) (Status: PROPOSED STANDARD) 2023 IP Version 6 Over PPP. D. Haskin, E. Allen. October 1996. (Format: TXT=20275 bytes) (Status: PROPOSED STANDARD) 2036 Observations on the Use of Components of the Class A Address Space Within the Internet. G. Huston. October 1996. (Format: TXT=20743 bytes) (Status: INFORMATIONAL) 2071 Network Renumbering Overview: Why Would I Want It and What Is It Anyway? P. Ferguson and H. Berkowitz. January 1997. (Format: TXT=33218 bytes) (Status: INFORMATIONAL) 2072 Router Renumbering Guide. H. Berkowtiz. January 1997. (Format: TXT=110591 bytes) (Status: INFORMATIONAL) 2073 An IPv6 Provider-based Unicast Address Format. Y. Rekhter, Pl Lothberg, R. Hinden, S. Deering, and J. Postel. January 1997. (Format: TXT=15549 bytes) (Obsoleted by RFC2374) (Status: PROPOSED STANDARD)
380
TCP/IP PRIMER PLUS
2080 RIPng for IPv6. G. Malkin, R. Minnear. January 1997. (Format: TXT=47534 bytes) (Status: PROPOSED STANDARD) 2081 RIPng Protocol Applicability Statement. G. Malkin. January 1997. (Format: TXT=6821 bytes) (Status: INFORMATIONAL) 2101 IPv4 Address Behavior Today. B. Carpenter, J. Crowcroft, and Y. Rekhter. February 1997. (Format: TXT=31407 bytes) (Status: INFORMATIONAL) 2133 Basic Socket Interface Extensions for IPv6. R. Gilligan, S. Thomson, J. Bound, and W. Stevens. April 1997. (Format: TXT=69737 bytes) (Status: INFORMATIONAL) 2147 TCP and UDP Over IPv6 Jumbograms. D. Borman. May 1997. (Format: TXT=1883 bytes) (Status: PROPOSED STANDARD) 2185 Routing Aspects of IPv6 Transition. R. Callon and D. Haskin. September 1997. (Format: TXT=31281 bytes) (Status: INFORMATIONAL) 2292 Advanced Sockets API for IPv6. W. Stevens and M. Thomas. February 1998. (Format: TXT=152077 bytes) (Status: INFORMATIONAL) 2373 IP Version 6 Addressing Architecture. R. Hinden, S. Deering. July 1998. (Format: TXT=52526 bytes) (Obsoletes RFC1884) (Status: PROPOSED STANDARD) 2374 An IPv6 Aggregatable Global Unicast Address Format. R. Hinden, M. ODell, and S. Deering. July 1998. (Format: TXT=25068 bytes) (Obsoletes RFC2073) (Status: PROPOSED STANDARD) 2375 Address Assignments. R. Hinden and S. Deering. July 1998. (Format: TXT=14356 bytes) (Status: INFORMATIONAL) 2391 Load Sharing Using IP Network Address Translation (LSNAT). P. Srisuresh and D. Gan. August 1998. (Format: TXT=44884 bytes) (Status: INFORMATIONAL) 2450 Proposed TLA and NLA Assignment Rule. R. Hinden. December 1998. (Format: TXT=24486 bytes) (Status: INFORMATIONAL) 2452 IP Version 6 Management Information Base for the Transmission Control Protocol. M. Daniele. December 1998. (Format: TXT=19066 bytes) (Status: PROPOSED STANDARD) 2454 IP Version 6 Management Information Base for the User Datagram Protocol. M. Daniele. December 1998. (Format: TXT=15862 bytes) (Status: PROPOSED STANDARD) 2460 Internet Protocol, Version 6 (IPv6) Specification. S. Deering and R. Hinden. December 1998. (Format: TXT=85490 bytes) (Obsoletes RFC1883) (Status: DRAFT STANDARD) 2461 Neighbor DiscOvery for IP Version 6(IPv6). T. Narten, E. Nordmark, and W. Simpson. December 1998. (Format: TXT=222516 bytes) (Obsoletes RFC1970) (Status: DRAFT STANDARD) 2462 IPv6 Stateless Address Autoconfiguration. S. Thomson and T. Narten. December 1998. (Format: TXT=61210 bytes) (Obsoletes RFC1971) (Status: DRAFT STANDARD)
381
2463 Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification. A. Contra and S. Deering. Decemer 1998. (Format: TXT=34190 bytes) (Obsoletes RFC1885) (Status: DRAFT STANDARD) 2464 Transmission of IPv6 Packets Over Ethernet Networks. M. Crawford. December 1998. (Format: TXT=12725 bytes) (Obsoletes RFC1972) (Status: PROPOSED STANDARD) 2465 Management Information Base for IP Version 6: Textual Conventions and General Group. D. Haskin and S. Onishi. December 1998. (Format: TXT=77339 bytes) (Status: PROPOSED STANDARD) 2466 Management Information Base for IP Version 6:ICMPv6 Group. D. Haskin and S. Onishi. December 1998. (Format: TXT=27547 bytes) (Status: PROPOSED STANDARD) 2467 Transmission of IPv6 Packets Over FDDI Networks. M. Crawford. December 1998. (Format: TXT=16028 bytes) (Obsoletes RFC2019) (Status: PROPOSED STANDARD) 2470 Transmission of IPv6 Packets Over Token Ring Networks. M. Crawford, T. Narten, and S. Thomas. December 1998. (Format: TXT=21677 bytes) (Status: PROPOSED STANDARD) 2471 IPv6 Testing Address Allocation. R. Hinden, R. Fink, and J. Postel. December 1998. (Format: TXT=8031 bytes) (Obsoletes RFC1897) (Status: EXPERIMENTAL) 2472 IP Version 6 Over PPP. D. Haskin, E. Allen. October 1996. (Format: TXT=20275 bytes) (Status: PROPOSED STANDARD) 2473 Generic Packet Tunneling in IPv6 Specification. A. Contra and S. Deering. December 1998. (Format: TXT=77956 bytes) (Status: PROPOSED STANDARD) 2491 IPv6 Over Non-broadcast Multiple Access (NBMA) networks. G. Armitage. P. Schulter, M. Jork, and G. Harter. January 1999. (Format: TXT=100782 bytes) (Status: PROPOSED STANDARD) 2492 IPv6 Over ATM Networks. G.Armitage, P. Schulter, M. Jork January 1999. (Format: TXT=21199 bytes) (Status: PROPOSED STANDARD) 2497 Transmission of IPv6 Packets Over ARCnet Networks. I. Souvatzis. January 1999. (Format: TXT=10304 bytes) (Also RFC1201) (Status: PROPOSED STANDARD) 2526 Reserved IPv6 Subnet Anycast Addresses. D. Johnson and S. Deering. March 1996. (Format: TXT=14555 bytes) (Status: PROPOSED STANDARD) 2529 Transmission of IPv6 Over IPv4 Domains Without Explicit Tunnels. B. Carpenter and C. Jung. March 1999. (Format: TXT=21049 bytes) (Status: PROPOSED STANDARD) 2545 Use of BGP-4 Multiprotocol Extensions for IPv6 Interdomain Routing. P. Marques and F Dupont. March 1999. (Format: TXT=10209 bytes) (Status: PROPOSED STANDARD) . 2546 6Bone Routing Practice. A. Durand and B. Buclin. March 1999. (Format: TXT=17844 bytes) (Status: PROPOSED STANDARD)
382
TCP/IP PRIMER PLUS
2553 Basic Socket Interface Extensions for IPv6. R. Gilligan, S. Thomson, J. Bound and S. Stevens. March 1999. (Format: TXT=89215 bytes) (Status: INFORMATIONAL) 2590 Transmission of IPv6 Packets Over Frame Relay 2675 IPv6 Jumbograms 2710 Multicast Listener DiscOvery (MLD) for IPv6 2711 IPv6 Router Alert Option
Chapter 6: Routing Protocols

823 DARPA Internet Gateway 827 Exterior Gateway Protocol Formal Specification 875 Gateways, Architectures, and Heffalumps 888 Exterior Gateway Protocol Formal Specification 890 Exterior Gateway Protocol Formal Specification 904 Exterior Gateway Protocol Formal Specification 911 EGP Gateway Under Berkeley UNIX 4.2 970 On Packet Switches With Infinite Storage 975 Autonomous Confederations 985 Requirements for Internet GatewaysDraft 1046 Queuing Algorithms to Provide Type-of-service for IP Links. W. Prue and J. Postel. Feb01-1988. (Format: TXT=30106 bytes) (Status: UNKNOWN) 1058 Routing Information Protocol. C.I. Hedrick. Jun-01-1988. (Format: TXT=93285 bytes) (Updated by RFC1388,RFC1723) (Status: HISTORIC) 1074 NSFNET Backbone SPF-Based Interior Gateway Protocol. J. Rekhter. Oct-01-1988. (Format: TXT=36000 bytes) (Obsoleted by RFC1323) (Status: UNKNOWN) 1075 Distance Vector Multicast Routing Protocol. D. Waitzman, C. partridge, and S. E. Deering. Nov-01-1988. (Format: TXT=54731 bytes) (Status: EXPERIMENTAL) 1092 EGP and Policy-based Routing in the New NSFNET Backbone. J. Rekhter. Feb-01-1989. (Format: TXT=11865 bytes) (Status: UNKNOWN) 1093 NSFNET Routing Architecture. H. W. Braun. Feb-01-1989. (Format: TXT=20629 bytes) (Status: UNKNOWN) 1102 Policy Routing in Internet Protocols. D. D. Clark. May-01-1989. (Format: TXT=59664 bytes) (Status: UNKNOWN)
383
1104 Models of Policy-based Routing. H. W. Braun. Jun-01-1989. (Format: TXT=25468 bytes) (Status: UNKNOWN) 1105 Border Gateway Protocol (BGP). K. Loughheed and Y.Rekhter. Jun-01-1989. (Format: TXT=37644 bytes) (Obsoleted by RFC1163) (Status: EXPERIMENTAL) 1125 Policy Requirements for Interadministrative Domain Routing. D. Estrin. Nov-01-1989. (Format: TXT=55248, PS=282123 bytes) (Status: UNKNOWN) 1131 OSPF Specification. J. Moy. Oct-01-1989. (Format: TXT=268, PS=857280 bytes) (Obsoleted by RFC1247) (Status: PROPOSED STANDARD) 1133 Routing Between the NSFNET and the DDN. J. Y. Yu and H. W. Braun. Nov-01-1989. (Format: TXT=23169 bytes) (Status: INFORMATIONAL) 1136 Administrative Domains and Routing Domains: A Model for Routing in the Internet. S. Hares and D. Katz. Dec-01-1989. (Format: TXT=22158 bytes) (Status: INFORMATIONAL) 1142 OSI IS-IS Intradomain Routing Protocol. D.Oran. Feb-01-1990. (Format: TXT=425379, PS=1204297 bytes) (Status: INFORMATIONAL) 1163 Border Gateway Protocol (BGP). K. Lougheed and Y Rekhter. Jun-01-1990. (Format: TXT=69404 bytes) (Obsoletes RFC1105) (Obsoleted by RFC1267) (Status: HISTORIC) 1164 Application of the Border Gateway Protocol on the Internet. J. C. Honig, D. Katz, M. Mathis, Y. Rekhter and J. Y. Yu. Jun-01-1990. (Format: TXT=56278 bytes) (Obsoleted by RFC1268) (Status: HISTORIC) 1195 Use of OSI IS-IS for Routing in TCP/IP and Dual Environments. R. W. Callon. Dec-011990. (Format: TXT=187866, PS=362052 bytes) (Status: PROPOSED STANDARD) 1222 Advancing the NSFNET Routing Architecture. H. W. Braun and Y. Rekhter. May-011991. (Format: TXT=15067 bytes) (Status: INFORMATIONAL) 1245 OSPF Protocol Analysis. J. Moy. Jul-01-1991. (Format: TXT=26160, PS=33546 bytes) (Also RFC1247,RFC1246) (Status: INFORMATIONAL) 1246 Experience With OSPF Protocol. J. Moy. Jul-01-1991. (Format: TXT=70441, PS=141924 bytes) (Also RFC1247, RFC1245) (Status: INFORMATIONAL) 1247 OSPF Version 2. J. Moy. Jul-01-1991. (Format: TXT=433332,PS=989724 bytes) (Obsoletes RFC1131) (Obsoleted by RFC1252) (Status: PROPOSED STANDARD) 1252 OSPF Version 2 Management Information Base. F Baker and R. Coltun. Aug-01-1991. . (Format: TXT=74471 bytes) (Obsoletes RFC1248) (Obsoleted by RFC1253) (Also RFC1247,RFC1245) (Status: PROPOSED STANDARD) 1253 OSPF Version 2 Management Information Base. F Baker and R. Coltun. Aug-01-1991. . (Format: TXT=74453 bytes) (Obsoletes RFC1252) (Obsoleted by RFC1850) (Also RFC1247, RFC1245, RFC1246) (Status: PROPOSED STANDARD)
384
TCP/IP PRIMER PLUS
1254 Gateway Congestion Control Survey. A. Mankin and K. Ramakrishnan. Jul-01-1991. (Format: TXT=67609 bytes) (Status: INFORMATIONAL) 1264 Internet Engineering Task Force Internet Routing Protocol Standardization Criteria. R. M. Hinden. Oct-01-1991. (Format: TXT=17016 bytes) (Status: INFORMATIONAL) 1265 BGP Protocol Analysis. Y. Rekhter. Oct-01-1991. (Format: TXT=20728 bytes) (Status: INFORMATIONAL) 1266 Experience With the BGP Protocol. Y. Rekhter. Oct-01-1991. (Format: TXT=21928 bytes) (Status: INFORMATIONAL) 1267 Border Gateway Protocol 3(BGP-3). K. Lougheed and Y. Rekhter. Oct-01-1991. (Format: TXT=80724 bytes) (Obsoletes RFC1163) (Status: HISTORIC) 1268 Application of the Border Gateway Protocol in the Internet. Y. Rekhter and P. Gross. Oct01-1991. (Format: TXT=31102 bytes) (Obsoletes RFC1164) (Obsoleted by RFC1655) (Status: HISTORIC) 1269 Definitions of Managed Objects for the Border Gateway Protocol: Version 3. S. Willis and J. W. Burruss. Oct-01-1991. (Format: TXT=25717 bytes) (Status: PROPOSED STANDARD) 1322 A Unified Approach to Interdomain Routing. D. Estrin, Y. Rekhter, and S. Hotz. May 1992. (Format: TXT=96934 byres) (Status: INFORMATIONAL) 1364 BGP OSPF Interaction. K. Varadhan. September 1992. 1370 Application Statement for the OSPF Internet Architecture Board, L. Chapin. October . 1992. (Format: TXT=4303 bytes) (Status: PROPOSED STANDARD) 1383 An Experience in DNS-based IP Routing 1387 RIP Version 2 Protocol Analysis. G. Malkin. January 1993. (Format: TXT=5998 bytes) (Obsoleted by RFC1721) (Status: INFORMATIONAL) 1388 RIP Version 2 Carrying Additional Information. G. Malkin. January 1993. (Format: TXT=16227 bytes) (Obsoleted by RFC17213) (Updates RFC1058) (Status: PROPOSED STANDARD) 1389 RIP Version 2 MIB Extensions. G. Malkin, F Baker. January 1993, (Format: TXT=23569 . bytes) (Obsoleted by RFC1724) (Status: PROPOSED STANDARD) 1397 Default Route Advertisement In BGP2 and BGP3 Version of The Border Gateway Protocol. D. Haskin. January 1993. (Format: TXT=4124 bytes) (Status: PROPOSED STANDARD) 1403 BGP OSPF Interaction. K. Varadhan. January 1993. (Format: TXT=36173 bytes) (Obsoletes RFC1290) (Also FY10010) (Status: INFORMATIONAL) 1465 Routing Coordination for X.400 MHS Services Within a Multi-Protocol/Multi-Network Environment Table Format V3 for Static Routing.
385
1477 IDPR as a Proposed Standard. M. Steenstrup. July 1993. (Format: TXT=77854 bytes) (Status: EXPERIMENTAL) 1478 An Architecture for Interdomain Policy Routing. M. Steenstrup. July 1993. (Format: TXT=275823 bytes) (Status: PROPOSED STANDARD) 1479 Inter-domain Policy Routing Protocol Specification: Version 1. M. Steenstrup. July 1993. (Format: TXT=275823 bytes) (Status: PROPOSED STANDARD) 1482 Aggregate Support in the NSFNET Policy-based Routing Database. Mark Knopper and Steven J. Richardson. July 1993. (Format: TXT=25330 bytes) (Status: INFORMATIONAL) 1504 Appletalk Update-based Routing Protocol: Enhanced Appletalk Routing. A. Oppenheimer. August 1993. (Format: TXT=201553 bytes) (Status: INFORMATIONAL) 1517 Applicability Statement for the Implementation of Classless Inter-Domain Routing (CIDR). Internet Engineering Steering Group, R. Hinden. September 1993. (Format: TXT=7357 bytes) (Status: PROPOSED STANDARD) 1519 Classless Interdomain Routing (CIDR): an Address Assignment and Aggregation Strategy. V. Fuller, T. Li, J. Yu, and K. Varadhan. September 1993. (Format: TXT=59998 bytes) (Obsoletes RFC1338) (Status: PROPOSED STANDARD) 1519 Exchanging Routing Information Across Provider Boundries in the CIDR Environment. Y. Rekhter and C. Topolcic. September 1993. (Format: TXT=20389 bytes) (Status: INFORMATIONAL) 1581 Protocol Analysis for Extensions to RIP to Support Demand Circuits. G. Meyer. February 1994. (Format: TXT=7536 bytes) 1582 Extensions to RIP to Support Demand Circuits. G. Meyer. February 1994. (Format: TXT=63271 bytes) (Status: PROPOSED STANDARD) 1583 OSPF Version 2. J. Moy. March 1994. (Format: TXT=532636, PS=990794 bytes) (Obsoletes RFC1247) (Obsoleted by RFC2178) (Status: DRAFT STANDARD) 1584 Multicast Extensions to OSPF J. Moy. March 1994. (Format: TXT=262463, PS=426358 . bytes) (Status: PROPOSED STANDARD) 1585 MOSPF: Analysis and Experience. J. Moy. March 1994. (Format: TXT=29754 bytes) (Status: INFORMATIONAL) 1586 Guidelines for Running OSPF Over Frame Relay Networks. O. deSouza and M. Rodrigues. March 1994. (Format: TXT=14968 bytes) (Status: INFORMATIONAL) 1587 The OSPF NSSA Option. R. Coltun and V. Fuller. March 1994. (Format: TXT=37412 bytes) (Status: PROPOSED STANDARD) 1654 A Border Gateway Protocol 4 (BGP-4). Y. Rekhter and T. Li, Editors. July 1994. (Format: TXT=130118 bytes) (Obsoleted by RFC1771) (Status: PROPOSED STANDARD)
386
TCP/IP PRIMER PLUS
1701 Generic Routing Encapsulation (GRE). S. Hanks, T. Li, D. Farinacci, and P. Traina. October 1994. (Format: TXT=15460 bytes) (Status: INFORMATIONAL) 1702 Generic Routing Encapsulation Over IPv4 Networks. S. Hanks, T. Li, D. Farinacci, and P. Traina. October 1994. (Format: TXT=7288 bytes) (Status: INFORMATIONAL) 1721 RIP Version 2 Protocol Analysis. G. Malkin. November 1994. (Format: TXT=6680 bytes) (Obsoletes RFC1387) (Status: INFORMATIONAL) 1722 RIP Version 2 Protocol Applicability Statement. G.Malkin. November 1994. (Format: TXT=10236 bytes) (Status: DRAFT STANDARD) 1723 RIP Version 2Carrying Additional Information. G. Malkin. November 1994. (Format: TXT=18597 bytes) (Obsoletes RFC1388) (Updates RFC1058) (Status: DRAFT STANDARD) 1745 BGP4/IDRP for IP-OSPF Interaction. K.Varadhan, S. Hares, and Y. Rekhter. December 1994. (Format: TXT=43675 bytes) (Status: PROPOSED STANDARD) 1765 OSPF Database Overflow. J.Moy. March 1995. (Format: TXT=21613 bytes) (Status: EXPERIMENTAL) 1771 A Border Gateway Protocol 4 (BGP-4). Y. Rekhter and T. Li. March 1995. (Format: TXT=11606 bytes) (Status: INFORMATIONAL) 1772 Application of the Border Gateway Protocol in the Internet. Y. Rekhter & P. Gross. March 1995. (Format: TXT=43916 bytes) (Obsoletes RFC1655) (Status: DRAFT STANDARD) 1773 of the BGP-4 protocol. P. Traina. March 1995. (Format: TXT=19936 bytes) (Obsoletes RFC1656) (Status: INFORMATIONAL) 1774 BGP-4 Protocol Analysis. P. Traina, Editor. March 1995. (Format: TXT=23823 bytes) (Status: INFORMATIONAL) 1786 Representation of the IP Routing Policies in a Routing Registry (ripe-81++). T. Bates, E. Gerich, L. Joncheray, J. M. Jouanigot, D. Karrenberg, M. Terpstra, and J. Yu. March 1995. (Format: TXT=133643 bytes) (Status: INFORMATIONAL) 1787 Routing in a Multi-provider Internet. Y. Rekhter. April 1995. (Format: TXT=20754 bytes) (Status: INFORMATIONAL) 1793 Extending OSPF to Support Demand Circuits. J. Moy. April 1995. (Format: TXT=16389 bytes) (Status: EXPERIMENTAL) 1817 CIDR and Classful Routing. Y. Rekhter. August 1995. (Format: TXT=3416 bytes) (Status: INFORMATIONAL) 1863 A BGP/IDRP Route Server Alternative to Full Mesh Routing. D. Haskin. October 1995. (Format: TXT=37426 bytes) (Obsoletes RFC1645 bytes) (Status: EXPERIMENTAL) 1923 RIPv1 Applicability Statement for Historic Status. J. Halpern & S. Bradner. March 1996. (Format: TXT=5560 bytes) (Status: INFORMATIONAL)
387
1965 Autonomous System Confederations for BGP. P. Traina. June 1996. (Format: TXT=13575 bytes) (Status: EXPERIMENTAL) 1966 BGP Route Reflection: An alternative to Full Mesh IBGP. T. Bates and R. Chandrasekeran. June 1996. (Format: TXT=14320 bytes) (Status: EXPERIMENTAL) 1992 The Nimrod Routing Architecture. I. Casineyra, N. Chiappa, and M. Steestrup. August 1996. (Format: TXT=46255 bytes) (Status: INFORMATIONAL) 1997 BGP Communities Attribute. R. Chandra, P. Traina, and T. Li. August 1996. (Format: TXT=8275 bytes) (Status: PROPOSED STANDARD) 1998 An Application of the BGP Community Attribute in Multi-home Routing. E. Chen & T. Bates. August 1996. (Format: TXT=16953 bytes) (Status: INFORMATIONAL) 2009 GPS-based Addressing and Routing. T. Imielinski and J. Navas. November 1996. (Format: TXT=66229 bytes) (Status: EXPERIMENTAL) 2082 RIP-2 MD5 Authentication. F Baker and R. Atkinson. January 1997. (Format: . TXT=25436 bytes) (Status: PROPOSED STANDARD) 2091 Triggered Extensions to RIP to Support Demand Circuits. G. Meyer and S. Sherry. January 1997. (Format: TXT=44835 bytes) (Status: PROPOSED STANDARD) 2092 Protocol Analylsis for Triggered RIP. S. Sherry, G. Meyer. January 1997. (Format: TXT=10865 bytes) (Status: INFORMATIONAL) 2102 Multicast Support for Nimrod: Requirements and Solution Approaches. R. Ramanathan. February 1997. (Format: TXT=50963 bytes) (Status: INFORMATIONAL) 2103 Mobility Support for Nimrod: Challenges and Solution Approaches. R. Ramanathan. February 1997. (Format: TXT=41352 bytes) (Status: INFORMATIONAL) 2117 Protocol Independent Multicast-Sparse Mode (PIM- SM): Protocol Specification. D. Estrin, D. Farinacci, A. Helmy, D. Thaler, S. Deering, M. Handley, V. Jacobson, C. Liu, P. Sharma, and L. Wei. June 1997. (Format: TXT=151886 bytes) (Obsoleted by RFC2362) (Status: EXPERIMENTAL) 2154 OSPF with Digital Signatures. S. Murphy, M. Badger, B. Wellington. June 1997. (Format: TXT=72701 bytes) (Status: EXPERIMENTAL) 2178 OSPF Version 2. J. Moy. July 1997. (Format: TXT=495866 bytes) (Obsoletes RFC1583) (Obsoleted by RFC2328) (Status: DRAFT STANDARD) 2189 Core-based Trees (CBT Version 2) Multicast Routing. A. Balardie. September 1997. (Format: TXT=52043 bytes) (Status: EXPERIMENTAL) 2201 Core-based Trees (CBT) Multicast Routing Architecture. A. Ballardie. September 1997. (Format: TXT=38040 bytes) (Status: EXPERIMENTAL) 2260 2260 Scalable Support for Multi-homed Multi-provider Connectivity. T. Bates, Y. Rekhter. January 1998. (Format: TXT=28085 bytes) (Status: INFORMATIONAL)
388
TCP/IP PRIMER PLUS
2270 Using a Dedicated AS for Sites Homed to a Single Provider. J. Stewart, T. Bates, R. Chadra, and E. Chen. January 1998. (Format: TXT=12063 bytes) (Status: INFORMATIONAL) 2280 Routing Policy Specification Language (RSPL). C. Alaettinoglu, T. Bates, E. Gerich, D. Karrenberg, D. Meyer, M. Terpstra, and C. Villamizar. January 1998. (Format: TXT=114985 bytes) (Status: PROPOSED STANDARD) 2281 Cisco Hot Standby Router Protocol (HSRP). T. Li, B. Cole, P. Morton, D.Li. March 1998. (Format: TXT=35161 bytes) (Status: INFORMATIONAL) 2283 Multiprotocol Extensions for BGP-4. T. Bates, R. Chandra, D. Katz, Y. Rekhter. February 1998. (Format: TXT=18946 bytes) (Status: PROPOSED STANDARD) 2328 OSPF Version 2. J. Moy. April 1998. (Format: TXT=447367 bytes) (Obsoletes RFC2178) (Also STD0054) (Status: STANDARD) 2329 OSPF Standardization Report. J. Moy. April 1998. (Format: TXT=15130 bytes) (Status: INFORMATIONAL) 2338 Virtual Router Redundancy Protocol. S. Knight, D. Weaver, D. Whipple, R. Hinden, D. Mitzel, P. Hunt, P. Higginson, M. Shand, and A. Lindem. April 1998. (Format: TXT=59871 bytes) (Status: PROPOSED STANDARD) 2362 Protocol Independent Multicast-Sparse Mode (PIM-SM): Protocol Specification. D. Estrin, D. Farinacci, A. Helmy, D. Thaler, S. Deering, M. Handley, V. Jacobson, C. Liu, P. Sharma, and L. Wei. June 1998. (Format: TXT=159833 bytes) (Obsoletes RFC2117) (Status: EXPERIMENTAL) 2370 The OSPF Opaque LSA Option. R. Coltun. July 1998. (Format: TXT=33789 bytes) (Also RFC2328) (Status: PROPOSED STANDARD) 2385 Protection of BGP Sessions via the TCP MD5 Signature Option. A. Heffernan. August 1998. (Format: TXT=12315 bytes) (Status: PROPOSED STANDARD) 2439 BGP Route Flap Damping. C. Villamiar, R. Chandra, R. Grovindan. November 1998. (Format: TXT=86376 bytes) (Status: PROPOSED STANDARD) 2453 RIP Version 2. G. Malkin. November 1998. (Format: TXT=98462 bytes) (Obsoletes RFC1388, RFC1723) (Updates RFC1723, RFC1388) (Also STD0056) (Status: STANDARD) 2519 A Framework for Interdomain Route Aggregation. E. Chen, J. Stewart. February 1999. (Format: TXT=25394 bytes) (Status: INFORMATIONAL) 2622 Routing Policy Specification Language (RPSL) 2650 Using RPSL in Practice 2676 QoS Routing Mechanisms and OSPF Extensions 2715 Interoperability Rules for Multicast Routing Protocols
389
Chapter 7: Transport/Host-to-Host Layer

1162 Connectionless Network Protocol (ISO 8473) and End Systems to Intermediate System (ISO 9542) Management Information Base. G. Satz. Jun-01-1990. (Format: TXT=109893 bytes) (Obsoleted by RFC1238) (Status: EXPERIMENTAL)
Chapter 8: Transmission Control Protocol (TCP)

675 Transmission Control Protocol 700 Protocol Exerperiment 721 Out-of-Band Control Signals in a Host-to-Host Protocol 761 Transmission Control Protocol 793 Transmission Control Protocol 794 Pre-emption 813 Window and Acknowledgement Strategy in TCP 872 TCP-on-a-LAN 879 TCP Maximum Segment Size and Related Topics 889 Internet Delay Experiments 896 Congestion Control in IP/TCP Internetworks 962 TCP-4 Prime 964 Some Problems With the Specifications of the Military Standard Transmission Control Protocol 1006 ISO Transport Services On Top of TCP: Version 3. M.T. Rose and D.E. Cass. May-011987. (Format: TXT=31935 bytes) (Obsoletes RFC0983) (Status: STANDARD) 1072 TCP Extensions for Long-delay Paths. V. Jacobson and R.T. Braden. Oct-01-1988. (Format: TXT=36000 bytes) (Obsoleted by RFC1323) (Status: UNKNOWN) 1078 TCP port service Multiplexer (TCPMUX). M.Lottor.Nov-01-1988. (Format: TXT=3248 bytes) (Status: UNKNOWN) 1106 TCP Big Window and NAK Options. R. Fox. Jun-01-1989. (Format: TXT=37105 bytes) (Status: UNKNOWN) 1110 Problem With the TCP Big Window Option. A. M. McKenzie. Aug-01-1989. (Format: TXT=5778 bytes) (Status: UNKNOWN)
390
TCP/IP PRIMER PLUS
1144 Compressing TCP/IP Headers for Low-speed Serial Links. V. Jacobson. Feb-01-1990. (Format: TXT=120959, PS=534729 bytes) (Status: PROPOSED STANDARD) 1185 TCP Extensions for High-speed Paths. V. Jacobson, R. T. Braden, and L. Zhang. Oct-011990. (Format: TXT=49508 bytes) (Obsoleted by RFC1323) (Status: EXPERIMENTAL) 1263 TCP Extensions Considered Harmful. S. OMalley and L. L. Peterson. Oct-01-1991. (Format: TXT=54078 bytes) (Status: INFORMATIONAL) 1323 TCP Extensions for High Performance. V. Jacobson, R. Braden, and D. Borman. May 1992. (Format: TXT=84558 bytes) (Obsoletes RFC1072, RFC1185) (Status: PROPOSED STANDARD) 1337 TIME-WAIT Assassination Hazards for TCP. R. Braden. May 1992. (Format: TXT=22887 bytes) (Status: INFORMATIONAL) 1379 Extending TCP for TransactionsConcepts. R. Braden. November 1992. (Format: TXT=91353 bytes) (Status: INFORMATIONAL) 1644 T/TCPTCP Extensions for Transactions Functional Specifications. R. Braden. July 1994. (Format: TXT=87362 bytes) (Status: EXPERIMENTAL) 1693 An Extension of TCP: Partial Order Service. T. Connolly, P. Amer, and P. Conrad. November 1994. (Format: TXT=26163 bytes) (Status: PROPOSED STANDARD) 2001 TCP Slow Start, Congestion Avoidance, Fast Retransmit, and Fast Recovery Algorithms. W. Stevens. January 1997. (Format: TXT=12981 bytes) (Status: PROPOSED STANDARD) 2018 TCP Selective Acknowledgement Options. M. Mathis, J. Mahdavi, S. Floyd, A. Romanow. October 1996. (Format: TXT=25671 bytes) (Status: PROPOSED STANDARD) 2140 TCP Control Block Interdependence. J. Touch. April 1997. (Format: TXT=26032 bytes) (Status: INFORMATIONAL) 2398 Some Testing Tools for TCP Implementors. S. Parker, C. Schmechel. August 1998. (Format: TXT=24107 bytes) (Obsoletes NONE) (Updates NONE) (Also NONE) (Status: INFORMATIONAL) 2414 Increasing TCPs Initial Window. M. Allman, S. Floyd, and C. Partridge. September 1998. (Format: TXT=32019 bytes) (Status: EXPERIMENTAL) 2415 Simulating Studies of Increased Initial TCP Window Size. K. Poduri and K. Nichols. September 1998. (Format: TXT=24205 bytes) (Status: INFORMATIONAL) 2416 When TCP Starts Up With Four Packets Into Only Three Buffers. T. Shepard, C. Partridge. September 1998. (Format: TXT=12663 bytes) (Status: INFORMATIONAL)
391
2488 Enhancing TCP Over Satellite Channels using Standard Mechanisms. M. Allman, D. Glover, and L. Sanchez. January 1999. (Format: TXT=47857 bytes) (Also BCP0028) (Status: BEST CURRENT PRACTICE) 2525 Known TCP Implementation Problems. V. Paxson, M. Allman, S. Dawson, W. Fenner, J. Griner, I. Heavens, K. Lahey, H. Semke, and B. Volz. March 1999. (Format: TXT=137201 bytes) (Status: INFORMATIONAL) 2581 TCP Congestion Control. M. Allman, V. Paxson, W. Stevens. April 1999. (Format: TXT=31351 bytes) (Obsolets RFC2001) (Status: PROPOSED STANDARD) 2582 The NewReno Modification to TCPS Fast Recovery Algorithm. S. Floyd, T. Henderson. April 1999. (Format: TXT=29393 bytes) (Status: EXPERIMENTAL)
Chapter 9: User Datagram Protocol (UDP)

768 User Diagram Protocol
Chapter 11: Telnet

91 Proposed User-User Protocol 97 First Cut at a Proposed Telnet Protcol 103 Implementation of Interrupt Keys 110 Response to NWG/RFC 110 114 File Transfer Protocol 135 Response to NWG/RFC 110 137 Telnet Protocola Proposed Document 139 Discussion of Telnet Protocol 158 Telnet Protocol: A Proposed Document 172 File Transfer Protocol 190 DEC PDP-10-IMLAC Communication System 205 NETCRTa Character Display Protocol 206 User Telneta Description of Initial Implementation 215 NCP, ICP, and Telnet: The Terminal IMP Implementation 216 Telnet Access to UCSBS Online System 265 File Transfer Protocol
392
TCP/IP PRIMER PLUS
318 Telnet Protocols 328 Suggested Telnet Protocol Changes 339 MLTNET: A Multi Telnet Subsystem for Tenex 340 Proposed Telnet Changes 346 Response to NWG/RFC 346 354 File Transfer Protocol 355 Response to NWG/RFC 346 357 Echoing Strategy for Satellite Links 377 Using TSO via ARPA Network Virtual Terminal 393 Comments on Telnet Protocol Changes 426 Reconnection Protocol 435 Telnet Issues 452 TELENET Command on Host LL 466 Telnet Logger/Server for Host LL-67 495 Telnet Protocol Specifications 513 Comments on New Telnet Specifications 529 Note on Protocol Synch Sequences 542 File Transfer Protocol 559 Comments on The New Telnet Protocol and its Implementation 560 Remote Controlled Transmission and Echoing Telnet Option 562 Modifications to the Telnet Specifications 563 Comments on the RCTE Telnet Option 570 Experimental Input Mapping Between NVT ASCII and UCSB Online System 576 Proposal and Identifying Linking 581 Corrections to RFC 560: Remote Controlled Transmission and Echoing Telnet Option 587 Announcing New Telnet Option 593 Telnet and FTP Implementation Schedule Change 594 Second Thoughts in Defense of Telnet Go-Ahead 600 Interfacing an Illinois Plasma Terminal to the ARPANET 651 Revised Telnet Status Option
393
652 Telnet Output Carriage-return Disposition Option 653 Telnet Output Horizontal Tabstops Option 654 Telnet Output Horizontal Tab Disposition Option 655 Telnet Output Formfeed Disposition Option 656 Telnet Output Vertical Tabstops Option 657 Telnet Output Vertical Tab Disposition Option 658 Telnet Output Linefeed Disposition 659 Announcing Additional Telnet Options 669 July, 1975 Survey of New-Protocol Telnet Servers 679 July, 1975 Survey of New-Protocol Telnet Servers 681 Network UNIX 688 Tentative Schedule for the New Telnet Implementation for the TIP 701 July, 1975 Survey of New-Protocol Telnet Servers 702 July, 1975 Survey of New-Protocol Telnet Servers 703 July, 1975 Survey of New-Protocol Telnet Servers 718 Comments on RCTE from the Tenex Implementation Experience 719 Discussion on RCTE 726 Remote Controlled Transmission and Echoing Telnet option 727 Telnet Logout Option 728 Minor Pitfall in the Telnet Protocol 729 Telnet Byte Macro Option 730 Telnet Data Entry Terminal Option 731 Telnet Data Entry Terminal Option 735 Revised Telnet Byte Macro Option 736 Telnet SUPDUP Option 746 SUPDUP Graphics Extension 747 Recent Extensions to the SUPDUP Protocol 748 Telnet SUPDUP-Output Option 764 Telnet Protocol Specifications 765 File Transfer Protocol
394
TCP/IP PRIMER PLUS
779 Telnet Send-Location Option 782 Virtual Terminal Management Protocol 818 Remote User Telnet Service 854 Telnet Protocol Specifications 855 Telnet Option Specifications 856 Telnet Binary Transmissions 857 Telnet Echo Option 858 Telnet Suppress Go-Ahead Option 859 Telnet Status Option 860 Telnet Timing Mark Option 861 Telnet Extended Options: List Option 884 Telnet Terminal Type Option 885 Telnet End of Record Option 927 TACACS User Identification Telnet Option 930 Telnet Terminal Type Option 946 Telnet Terminal Location Number Option 959 File Transfer Protocol 1041 Telnet 3270 Regime Option. Y. Rekhter. Jan-01-1988. (Format: TXT=11608 bytes) (Status: PROPOSED STANDARD) 1043 Telnet Data Entry Terminal option: DODIIS Implementation. A. Yasuda and T. Thompson. Feb-01-1988. (Format: TXT=59478 bytes) (Updates RFC0732) (Status: PROPOSED STANDARD) 1053 Telnet X.3 PAD Option. S. Levy and T. Jacobson. Apr-01-1988. (Format: TXT=48952 bytes) (Status: PROPOSED STANDARD) 1073 Telnet Window Size Option. D. Waitzman. Oct-01-1988. (Format: TXT=7639 bytes) (Status: PROPOSED STANDARD) 1079 Telnet Terminal Speed Option. C. L. Hedrick. Dec-01-1988. (Format: TXT=4942 bytes) (Status: PROPOSED STANDARD) 1080 Telnet Remote Flow Control Option. C. L. Hedrick. Nov-01-1099. (Format: TXT=6688 bytes) (Obsoleted by RFC1372) (Status: UNKNOWN) 1091 Telnet Terminal-type Option. J. VanBokkelen. Feb-01-1989. (Format: TXT=13439 bytes) (Obsoletes RFC0930) (Status: PROPOSED STANDARD)
395
1096 Telnet X Display Location Option. G. A. Marcy. Mar-01-1989. (Format: TXT=4634 bytes) (Status: PROPOSED STANDARD) 1097 Telnet Subliminal-Message option. B. Miller. Apr-01-1989. (Format: TXT=5490 bytes) (Status: UNKNOWN) 1116 Telnet Linemode Option. D. A. Borman. Aug-01-1989. (Format: TXT=47473 bytes) (Obsoleted by RFC1184) (Status: PROPOSED STANDARD) 1143 The Q Method of Implementing TELNET Option Negotiation. D. J. Bernstein. Feb-011990. (Format: TXT=23331 bytes) (Status: EXPERIMENTAL) 1184 Telnet Linemode Option. D. A. Borman. Oct-01-1990. (Format: TXT=53085 bytes) (Obsoletes RFC1116) (Status: DRAFT STANDARD) 1205 5250 Telnet Interface. P. Chmielewski. Feb-01-1991. (Format: TXT=27170 bytes) (Status: INFORMATIONAL) 1372 Telnet Remote Flow Control Option. C. Hedrick, D. Borman. October 1992. (Format: TXT=11098 bytes) (Obsoletes RFC1080) (Status: PROPOSED STANDARD) 1408 Telnet Environment Option. D. Borman, Editor. January 1993. (Format: TXT=13119 bytes) (Obsoleted by RFC1571) (Status: HISTORIC) 1409 Telnet Authentication Option. D. Borman, Editor. January 1993. (Format: TXT=13119 bytes) (Obsoleted by RFC1416) (Status: EXPERIMENTAL) 1411 Telnet Authentication: Kerberos Version 4. D. Borman, Editor. January 1993. (Format: TXT=7967 bytes) (Status: EXPERIMENTAL) 1412 Telnet Authentication: SPX.K. Alagappan. January 1993. (Format: TXT=6952 bytes) (Status: EXPERIMENTAL) 1416 Telnet Authentication Option. D. Borman, Editor. February 1993. (Format: TXT=13270 bytes) (Obsoletes RFC1409) (Status: EXPERIMENTAL) 1571 Telnet Environment Option Interoperability Issues. D. Borman. January 1994. (Format: TXT=8117 bytes) (Updates RFC1408) (Status: INFORMATIONAL) 1572 Telnet Environment Option. S. Alexander. January 1994. (Format: TXT=14676 bytes) (Status: PROPOSED STANDARD) 1576 TN3270 Current Practices. J. Penner. January 1994. (Format: TXT=24477 bytes) (Status: INFORMATIONAL) 1646 TN3270 Extensions for Luname and Printer Selection. C. Graves, T. Butts, and M. Angel. July 1994. (Format: TXT=27564 bytes) (Status: INFORMATIONAL) 1647 TN3270 Enhancements. B. Kelly. July 1994. (Format: TXT=84420bytes) (Obsoleted by RFC2355) (Status: PROPOSED STANDARD) 1921 TNVIP Protocol. J. Dujonc. March 1996. (Format: TXT=57475 bytes) (Status: INFORMATIONAL)
396
TCP/IP PRIMER PLUS
2066 TELNET CHARSET Option. R. Gellens. January 1997. (Format: TXT=26088 bytes) (Status: EXPERIMENTAL) 2217 Telnet Com Port Control Option. G. Clark. October 1997. (Format: TXT=31664 bytes) (Status: EXPERIMENTAL) 2355 TN3270 Enhancements. B. Kelly. June 1998. (Format: TXT=89394 bytes) (Obsoletes RFC1647) (Status: DRAFT STANDARD)
Chapter 12: File Transfer Protocol (FTP)

133 File Transfer and Recovery 141 Comments on RFC 114: A File Transfer Protocol 238 Comments on DTP and FTP Proposals 250 Some Thoughts on File Transfer 269 Some Experience with File Transfer 281 Suggested Addition to File Transfer Protocol 294 The Use of Set Data Type Transaction in File Transfer Protocol 310 Another Look at Data and File Transfer Protocols 385 Comments on the File Transfer Protocol 412 User FTP Documentation 413 File Transfer Protocol (FTP) Status and Further Comments 430 Comments on File Transfer Protocol 438 FTP Server-Server Interaction 448 Print Files in FTP 463 FTP Comments and Response to RFC 430 468 FTP Data Compression 478 FTP Server-Server InteractionII 479 Use of the FTP by the NIC Journal 480 Host-dependent FTP Parameters 486 Data Transfer Revisited 487 Free File Transfer 501 Un-muddling Free File Transfer 505 Two Solutions to a File Transfer Access Problem
397
506 FTP Command Naming Problem 520 Memo to FTP Group: Proposal for File Access Protocol 532 UCSD-CC Server-FTP Facility 535 Comments on File Access Protocol 571 Tenex FTP Problem 607 Comments on the File Transfer Protocol 614 Response to RFC 607: Comments on the File Transfer Protocol 624 Comments on the File Transfer Protocol 630 FTP Error Code Usage for More Reliable Mail Service 640 Revised FTP Reply Codes 691 One More Try on the FTP 697 CWD Command of FTP 737 FTP Extension: XSEN 743 FTP Extension: XRSO/XRCP 775 Directory-oriented FTP Commands 949 FTP Unique-named Store Command 1415 FTP-FTAM Gateway Specification. J. Mindel and R. Slaski. January 1993. (Format: TXT=128261 bytes) (Status: PROPOSED STANDARD) 1440 SIFT/UFT: Sender-initiated/Unsolicited File Transfer. R. Troth. July 1993. (Format: TXT=17366 bytes) (Status: EXPERIMENTAL) 1545 FTP Operations Over Big Address Records (FOOBAR). D. Piscitello. November 1993. (Format: TXT=8985 bytes) (Obsoleted by RFC1639) (Status: EXPERIMENTAL) 1579 Firewall-friendly FTP. S. Bellovin. February 1994. (Format: TXT=8806 bytes) (Status: INFORMATIONAL) 1635 How to Use Anonymous FTP. P. Deutsch, A. Emtage, and A. Marine. May 1994. (Format: TXT=27259 bytes) (Also FY10024) (Status: INFORMATIONAL) 1639 FTP Operations Over Big Address Records (FOOBAR). D. Piscitello. June 1994. (Format: TXT=10055 bytes) (Obsoletes RFC1545) (Status: EXPERIMENTAL) 2204 ODETTE File Transfer Protocol. D. Nash. September 1997. (Format: TXT=151857 bytes) (Status: INFORMATIONAL) 2228 FTP Security Extensions. M. Horowitz, S. Lunt. October 1997. (Format: TXT=58733 bytes) (Updates RFC0959) (Status: PROPOSED STANDARD)
398
TCP/IP PRIMER PLUS
2389 Feature Negotiation Mechanism for the File Transfer Protocol. P. Hethmon and R. Elz. August 1998. (Format: TXT=18536 bytes) (Also RFC0959) (Status: PROPOSED STANDARD) 2428 FTP Extensions for IPv6 and NATs. M. Allman, S. Ostermann, and C. Metz. September 1998. (Format: TXT=16028 bytes) (Status: PROPOSED STANDARD) 2577 FTP Security Considerations. M. Allman and S. Ostermann. May 1999. (Format: TXT=17870 bytes) (Status: INFORMATIONAL) 2640 Internationalization of File Transfer Protocol
Chapter 13: Simple Mail Transfer Protocol (SMTP)

196 Revision of the Mail Box Protocol 221 Revision of the Mail Box Protocol 224 Revision of the Mail Box Protocol 278 Revision of the Mail Box Protocol 333 Proposed Experiment with a Message Switching Protocol 458 Mail Retrieval via FTP 475 FTP and Network Mail System 491 What is Free? 498 On Mail Service to CCN 524 Thoughts on the Mail Protocol Proposed in RFC 524 539 Thoughts on the Mail Protocol Proposed in RFC 524 555 Responses to Critiques of the Proposed Mail Protocol 561 Standardized Network Mail Headers 574 Announcement of a Mail Facility at UCSB 577 Mail Priority 644 On the Problem of Signature Authentification for Network Mail 680 Message Transmission Protocol 706 On the Junk Mail Problem 720 Address Specification Syntax for Network Mail 724 Proposed Official Standard for the Format of ARPA Network Text Messages
399
732 Standard for the Format of ARPA Network Text Messages 744 MARSa Message Archiving and Retrieval Service 751 Survey of FTP mail and MLFL 753 Internet Message Protocol 754 Out-of-net Host Addresses for Mail 757 Suggested Solution to the Naming, Addressing, and Delivery Problem for ARPANET Message System 763 Role Mailboxes 771 Mail Transition Plan 772 Mail Transfer Protocol 780 Mail Transfer Protocol 784 Mail Transfer Protocol: ISI TOPS20 Implementation 785 Mail Transfer Protocol: ISI TOPS20 File Definitions 786 Mail Transfer Protocol: ISI TOPS20 MTP-NIMAIL Interface 788 Simple Mail Transfer Protocol 806 Proposed Federal Information Processing Standard: Specification for Message Format for Computer-based Message Systems 821 Simple Mail Transfer Protocol 822 Standard for the Format of ARPA Internal Text Messages 841 Specification for Message Format for the Computer-based Message System 886 Proposed Standard for Message Header Munging 915 Network Mail Path Service 918 Post Office Protocol: Version 2 934 Proposed Standard for Message Encapsulation 937 Post Office Protocol: Version 2 974 Mail Routing and the Domain System 975 UUCP Mail Interchange Format Standard 976 Network News Transfer Protocol 984 PCMAIL: A Distributed Mail System for Personal Computers 987 Addendum to RFC 987: (Mapping Between X.400 and RFC-822)
400
TCP/IP PRIMER PLUS
993 PCMAIL: A Distributed Mail System for Personal Computers 1026 Addendum to RFC 987:(Mapping Between X.400 and RFC-822). S.E. Kille. Sep-011987. (Format: TXT=7117 bytes) (Obsoleted by RFC1327, RFC1495, RFC2156) (Updates RFC0987) (Updated by RFC1138, RFC1148) (Status: UNKNOWN) 1047 Duplicate Messages and SMTP. C. Partridge. Feb-01-1998. (Format: TXT=15423 bytes) (Obsoleted by RFC1084, RFC1395, RFC1497, RFC1533) (Status: UNKNOWN) 1049 Content-type Header Field for Internet Messages. M. A. Sirbu. Mar-01-1988. (Format: TXT=51540 bytes) (Obsoleted by RFC1057) (Status: HISTORIC) 1056 PCMAIL: A Distributed Mail System for Personal Computers. M. L. Lambert. Jun-011988. (Format: TXT=12911 bytes) (Status: STANDARD) 1064 Interactive Mail Access Protocol: Version 2. M. R. Crispin. Jul-01-1988. (Format: TXT=57813 bytes) (Obsoleted by RFC1176, RFC1203) (Status: UNKNOWN) 1081 Post Office Protocol: Version 3. M. T. Rose. Nov-01-1988. (Format: TXT=37009 bytes) (Obsoleted by RFC1225) (Status: UNKNOWN) 1082 Post Office Protocol: Version 3. Extended Service Offerings. M. T. Rose. Nov-01-1988. (Format: TXT=25423 bytes) (Obsoleted by RFC1225) (Status: UNKNOWN) 1090 SMTP on X.25. R. Ullmann. Feb-01-1989. (Format: TXT=6141 bytes) (Status: UNKNOWN) 1113 Privacy enhancement for Internet Electronic Mail: Part IMessage Encipherment and Authentication Procedures. J. Linn. Aug-01-1989. (Format: TXT=89293 bytes) (Obsoletes RFC0989, RFC1040) (Obsoleted by RFC1421) (Status: HISTORIC) 1114 Privacy Enhancement for Internet Electronic Mail: Part II Certificatebased Key management. S. T. Kent, J. Linn. Aug-01-1989. (Format: TXT=69661 bytes) (Obsoleted by RFC1422) (Status: HISTORIC) 1115 Privacy Enhancement for Internet electronic mail: Part IIIAlgorithms, Modes, and Identifiers. J. Linn. Aug-01-1989. (Format: TXT=18226 bytes) (Obsoleted by RFC1422) (Status: HISTORIC) 1137 Mapping Between Full RFC 822 and RFC 822 with Restricted Encoding. S. Kille. Dec01-1989. (Format: TXT=6266 bytes) (Updates RFC0976) (Status: HISTORIC) 1138 Mapping Between X.400(1988)/ISO 10021 and RFC 822. S. E. Kille. Dec-01-1989. (Format: TXT=191029 bytes) (Obsoleted by RFC1327, RFC1495, RFC2156) (Updates RFC0822, RFC0987, RFC1026) (Updated by arfc1148) (Status: EXPERIMENTAL) 1148 Mapping Between X.400 (1988)/ISO 10021 and RFC 822. S.E. Kille. 1153 Digest Message Format. F J. Wancho. Apr-01-1990. (Format: TXT=6632 bytes) (Status: . EXPERIMENTAL)
401
1154 Encoding Header Message Field for Internet Messages. D. Robinson and R. Ullmann. Apr-01-1990. (Format: TXT=12214 bytes) (Obsoleted by RFC1505) (Status: EXPERIMENTAL) 1168 Intermail and Commercial Mail Relay Services. A. Westine, A. L. DeSchon, J. Postel, C. E. Ward. Jul-01-1990. (Format: TXT=149816 bytes) (Status: INFORMATIONAL) 1176 Interactive Mail Access Protocol: Version 2. M. R. Crispin. Aug-01-1990. (Format: TXT=67330 bytes) (Obsoletes RFC1064) (Status: EXPERIMENTAL) 1203 Interactive Mail Access Protocol: Version 3. J. Rice. Feb-01-1991. (Format: TXT=123325 bytes) (Obsoletes RFC1064) (Status: HISTORIC) 1204 Message Posting Protocol (MPP). S. Yeh, D. Lee. Feb-01-1991. (Format: TXT=11371 bytes) (Status: EXPERIMENTAL) 1211 Problems With Maintenance of Large Mailing Lists. A. Westine, J. Postel. Mar-01-1991. (Format: TXT96167 bytes) (Status: INFORMATIONAL) 1225 Post Office Protocol: Version 3. M. T. Rose. May-01-1991. (Format: TXT=37340 bytes) (Obsoleted RFC1081) (Obsoleted by RFC1460) (Status: DRAFT STANDARD) 1327 Mapping Between X.400(1988)/ISO 10021 and RFC 822. S. Hardcatle-Kile. May 1992. (Format: TXT=228598 bytes) (Obsoletes RFC987, RFC1026, RFC1138, RFC1148) (Obsoleted by RFC1495, RFC2156) (Updates RFC0822, rfc0822) (Status: PROPOSED STANDARD) 1339 Remote Mail Checking Protocol. S. Dorner and P. Resnick. June 1992. (Format: TXT=13115 bytes) (Status: EXPERIMENTAL) 1341 Multipurpose Internet Mail Extensions (MIME) Part One: Format of Internet Message Bodies. N. Borenstein and N. Freed. June 1992. (Format: TXT=211117, PS=347082 bytes) (Obsoleted by RFC1521) (Status: PROPOSED STANDARD) 1342 MIME (Multipurpose Internet Mail Extensions), Part Three. K. Moore. June 1992. (Format: TXT=15845 bytes) (Obsoleted by RFC1522) (Status: INFORMATIONAL) 1343 A User Agent Configuration Mechanism for Multimedia Mail Format Information. N. Borenstein. June 1992. (Format: TXT=29295, PS=59978 bytes) (Status: INFORMATIONAL) 1344 Implications of MIME for Internet Gateways. N. Borenstein. June 1992. (Format: TXT=25872, PS=51812 bytes) (Status: INFORMATIONAL) 1357 A Format for E-mailing Bibliographic Records. D. Cohen. July 1992. (Format: TXT=25021 bytes) (Obsoleted by RFC1807) (Status: INFORMATIONAL) 1405 Mapping Between X.400 (1984/1988) and Mail-11 (DECnet mail). C. Allocchio. January 1993. (Format: TXT=33885 bytes) (Obsoleted by RFC2162) (Status: EXPERIMENTAL)
402
TCP/IP PRIMER PLUS
1425 SMTP Service Extensions. J. Klensin, WG Chair, N. Freed, Editor, M. Rose, E. Stefferud & D. Crocker. February 1993. (Format: TXT=20932 bytes) (Obsoleted by RFC1651) (Status: PROPOSED STANDARD) 1426 SMTP Service Extension for 8bit-MIMEtransport. J. Klenisin; W. G. Chair; N. Freed, Editor; M. Rose; E. Stefferud; and D. Crocker. February 1993. (Format: TXT=1161 bytes) (Obsoleted by RFC1652) (Status: PROPOSED STANDARD) 1427 SMTP Service Extension for Message Size Declaration. J. Klensin; W. G. Chair; N. Freed, Editor; K. Moore. February 1993. (Format: TXT=17856 bytes) (Obsoleted by RFC1653) (Status: PROPOSED STANDARD) 1428 Transition of Internet Mail from Just-Send-8 to 8-bit SMTP/MIME. G. Vaudreuil. February 1993. (Format: TXT=12064 bytes)(Status: INFORMATIONAL) 1460 Post Office Protocol, Version 3. M. Rose. June 1993. (Format: TXT=38827 bytes) (Obsoletes RFC1225) (Obsoleted by RFC1725) 1494 Equivalences Between 1988 X.400 and RFC-822 Message Bodies. H. Alvestrand & S. Thompson. August 1993. (Format: TXT=37273 bytes) (Status: PROPOSED STANDARD) 1495 Mapping Between X.400 and RFC-822 Message Bodies. H. Alvestrand, S. Kille, R. Miles, M. Rose, and S. Thompson. August 1993. (Format: TXT=20071 bytes) (Obsoletes RFC987, RFC987, RFC1026, RFC1138, RFC1148, RFC1327) (Obsoleted by RFC2156) (Status: PROPOSED STANDARD) 1496 Rules for Downgrading Messages from X.400/88 to X.400/84 when MIME Content Types are Present in the Messages. H. Alvestrand, J. Romaguera, and K. Jordan. August 1993. (Format: TXT=8411 bytes) (Status: PROPOSED STANDARD) 1502 X.400 Use of Extended Character Sets. H. Alvestrand. August 1993. (Format: TXT=27976 bytes) (Status: PROPOSED STANDARD) 1505 Encoding Header Message Field for Internet Messages. A. Costanzo, D. Robinson, and R. Ullmann. August 1993. (Format: TXT=63796 bytes) (Obsoletes RFC1154) (Status: EXPERIMENTAL) 1506 A Tutorial on Gatewaying Between X.400 and Internet Mail. J. Houttuin. September 1993. (Format: TXT=85550 bytes) (Status: INFORMATIONAL) 1521 Multipurpose Internet Mail Extensions (MIME) Part One: Mechanisms for Specifying and Describing the Format of Internet Message Bodies. N. Borenstein and N. Freed. September 1993. (Format: TXT=187424, PS=393670 bytes) (Obsoletes RFC1341) (Obsoleted by RFC2045, RFC2046, RFC2047, RFC2048, RFC2049, BCP0013) (Updated by RFC1590) (Status: DRAFT STANDARD) 1522 MIME (Multipurpose Internet Mail Extensions), Part Two: Message Header Extensions for Non-ASCII Text. K. Moore. September 1993. (Format: TXT=22502 bytes) (Obsoletes RFC1342) (Obsoleted by RFC2045, RFC2046, RFC2047, RFC2048, RFC2049, BCP0013) (Status: DRAFT STANDARD)
403
1523 The Text-enriched MIME Content Type. N. Borenstein. September 1993. (Format: TXT=32691 bytes) (Obsoleted by RFC1563, RFC1896) (Status: INFORMATIONAL) 1524 A User Agent Configuration Mechanism for Multimedia Mail Format Information. N. Borenstein. September 1993. (Format: TXT=26464 bytes) (Status: INFORMATIONAL) 1544 The Content-MD5 Header Field. M. Rose. November 1993. (Format: TXT=6478 bytes) (Obsoleted by RFC1864) (Status: PROPOSED STANDARD) 1556 Handling of Bidirectional Texts in MIME. H. Nussbacher and Y. Bourvine. December 1993. (Format: TXT=9273 bytes) (Status: INFORMATIONAL) 1563 The Text-enriched MIME Content Type. N. Borenstein. January 1994. (Format: TXT=32913, PS=73543 bytes) (Obsoletes RFC1523) (Obsoleted by RFC1896) (Status: INFORMATIONAL) 1590 Media Type Registration Procedure. J. Postel. March 1994. (Format: TXT=13044 bytes) (Obsoleted by RFC2045, RFC2046, RFC2047, RFC2048, RFC2049, BCP0013) (Updates RFC1521) (Status: INFORMATIONAL) 1615 Migrating Form X.400(84)to X.400(88). J. Houttuin and J. Craigie. May 1994. (Format: TXT=39693 bytes) (Status: INFORMATIONAL) 1616 X.400(1988)for the Academic and Research Community in Europe. RARE WG-MSG Task Force 88. E. Huizer and J. Romaguera, Editors. May 1994. (Format: TXT=107432 bytes) (Status: INFORMATIONAL) 1641 Using Unicode With MIME. D. Goldsmith and M. Davis. July 1994. (Format: TXT=11258, PS=20451 bytes) (Status: EXPERIMENTAL) 1642 UTF-7 A Mail-safe Transformation Format of Unicode. D. Goldsmith and M. Davis. July 1994. (Format: TXT=27770, PS=50907 bytes) (Obsoleted by RFC2152) (Status: EXPERIMENTAL) 1648 Postmaster Convention for X.400 Operations. A. Cargille. July 1994. (Format: TXT=8761 bytes) (Status: PROPOSED STANDARD) 1649 Operational Requirements for X.400 Management Domain in the GO-MHS Community. R. Hagens and A. Hansen. July 1994. (Format: TXT=23138 bytes) (Status: INFORMATIONAL) 1651 SMTP Service Extensions. Klensin, N. Freed, M. Rose, E. Stefferud, and D. Crocker. July 1994. (Format: TXT=22153 bytes) (Obsoletes RFC1425) (Obsoleted by RFC1869, STD0010) (Status: DRAFT STANDARD) 1652 SMTP Service Extension for 8-bit MIME Transport. Klensin, N.Freed, M. Rose, E. Stefferud, and D. Crocker. July 1994. (Format: TXT=11842 bytes) (Obsoletes RFC1426) (Status: DRAFT STANDARD) 1653 SMTP Service Extension for Message Size Declaration. J. Klenisn, N. Freed, and K. Moore. July 1994. (Format: TXT=17883 bytes) (Obsoletes RFC1427) (Obsoleted by RFC1870, STD0011) (Also STD0011) (Status: DRAFT STANDARD)
404
TCP/IP PRIMER PLUS
1685 Writing X.400 O/R Names. H. Alvestrand. August 1994. (Format: TXT=21242 bytes) (Also RTR0012) (Status: INFORMATIONAL) 1711 Classifications in E-mail Routing. J. Houttuin. October 1994. (Format: TXT=47584 bytes) (Status: INFORMATIONAL) 1725 Post Office Protocol, Version 3. J. Meyers and M. Rose. November 1994. (Format: TXT=35058 bytes) (Obsoletes RFC1460) (Obsoleted by RFC1939, STD0053) (Status: DRAFT STANDARD) 1730 Internet Message Access Protocol, Version 4. M. Crispin. December 1994. (Format: TXT=156660 bytes) (Obsoleted by RFC2060, RFC2061) (Status: PROPOSED STANDARD) 1731 IMAP4 Authentication Mechanisms. J. Myers. December 1994. (Format: TXT=11433 bytes) (Status: PROPOSED STANDARD) 1732 IMAP4 COMPATABILITY WITH IMPAP2 AND IMPA2BIS. M. Crispin. December 1994. (Format: TXT=9276 bytes) (Status: INFORMATIONAL) 1733 DISTRIBUTED ELECTRONIC MAIL MODELS IN IMAP4. M. Crispin. December 1994. (Format: TXT=6205 bytes) (Status: INFORMATIONAL) 1734 POP3 Authentication command. J. Myers. December 1994. (Format: TXT=8499 bytes) (Status: PROPOSED STANDARD) 1740 MIME Encapsulation of Macintosh FilesMacMIME. P. Falstrom, D. Crocker, and E. Fair. December 1994. (Format: TXT=31297 bytes) (Status: PROPOSED STANDARD) 1741 MIME Content-type for BinHex Encoded Files. P. Faltstrom, D. Crocker, and E. Fair. December 1994. (Format: TXT=10155 bytes) (Status: INFORMATIONAL) 1767 MIME Encapsulation of EDI Objects. D. Crocker. March 1995. (Format: TXT=15293 bytes) (Status: PROPOSED STANDARD) 1806 Communicating Presentation Information in Internet Messages: The Content-Disposition Header. R. Troost and S. Dorner. June 1995. (Format: TXT=15548 bytes) 1807 A Format for Bibliographic Records. R. Lasher and D. Cohen. June 1995. (Format: TXT=29417 bytes) (Obsoletes RFC1357) (Status: INFORMATIONAL) 1820 Multimedia E-mail (MIME) User Agent Checklist. E. Huizer. August 1995. (Format: TXT=14672 bytes) (Obsoleted by RFC1844) (Status: INFORMATIONAL) 1830 SMTP Service Extensions for Transmission of Large and Binary MIME Messages. G. Vaudreuil. August 1995. (Format: TXT=16555 bytes) (Status: EXPERIMENTAL) 1838 Use of an X.500/LDAP Directory to Support Mapping Between X.400 and RFC 822 Addresses. S. Kille. August 1995. (Format: TXT=12216 bytes) (Obsoleted by RFC2164) (Status: EXPERIMENTAL) 1844 Multimedia E-mail (MIME) User Agent Checklist. E. Huizer. August 1995. (Format: TXT=15072 bytes) (Obsoletes RFC1820) (Status: INFORMATIONAL)
405
1845 SMTP Service Extension for Checkpoint/Restart. D. Crocker, N. Freed and A. Cargille. September 1995. (Format: TXT=15399 bytes) (Status: EXPERIMENTAL) 1846 SMTP 521 Reply Code. A. Durand and F Dupont. September 1995. (Format: . TXT=6558 bytes) (Status: EXPERIMENTAL) 1847 Security Multiparts for MIME: Multipart/Signed and Multipart/Encrypted. J. Galvin, S. Murphy, S. Crocker, and N. Freed. October 1995. (Format: TXT=23679 bytes) (Status: PROPOSED STANDARD) 1848 MIME Objects Security Services. S. Crocker, N. Freed, J. Galvin, and S. Murphy. October 1995. (Format: TXT=95010 bytes) (Status: PROPOSED STANDARD) 1854 SMTP Service Extension for Command Pipelining. N. Freed. October 1995. (Format: TXT=14097 bytes) (Obsoleted by RFC2197) (Status: PROPOSED STANDARD) 1864 The Content-MD5 Header Field. J. Myers and M. Rose. October 1995. (Format: TXT=7216 bytes) 1869 SMTP Service Extensions. J. Klensin, N. Freed, M. Rose, E. Stefferud, and D. Crocker. November 1995. (Format: TXT=23299 bytes) (Obsoleted by RFC1651) (Also STD0010) (Status: STANDARD) 1870 SMTP Service Extension for Message Size Declaration. J.Klensin, N. Freed, and K. Moore. November 1995. (Format: TXT=18226 bytes) (Obsoletes RFC1653) (Also STD0010) (Status: STANDARD) 1872 The MIME Multipart/Related Content-type. E. Levinson. December 1995. (Format: TXT=15565 bytes) (Obsoleted by RFC2112) (Status: EXPERIMENTAL) 1873 Message/External-Body Content-ID Access Type. E. Levinson. December 1995. (Format: TXT=5878 bytes) (Status: EXPERIMENTAL) 1891 SMTP Service Extension for Delivery Status Notifications. K. Moore. January 1996. (Format: TXT=65192 bytes) (Status: PROPOSED STANDARD) 1892 The Multipart/Report Content-type for the Reporting of Mail System Administrative Messages. G. Vaudreuil. January 1996. (Format: TXT=7800 bytes) (Status: PROPOSED STANDARD) 1893 Enhanced Mail System Status Codes. G. Vaudreuil. January 1996. (Format: TXT=28218 bytes) (Status: PROPOSED STANDARD) 1894 An Extensible Message Format for Delivery Status Notifications. K. Moore and G. Vaudreuil. January 1996. (Format: TXT=77462 bytes) (Status: PROPOSED STANDARD) 1895 The Application/CALS-1840 Content-type. E. Levinson. February 1996. (Format: TXT=10576 bytes) (Status: INFORMATIONAL) 1896 The text/enriched MIME Content-type. P. Resnick & A. Walker. February 1996. (Format: TXT=45926, PS=81217 bytes) (Obsoletes RFC1523, RFC1563) (Status: INFORMATIONAL)
406
TCP/IP PRIMER PLUS
1957 Some Observations on Implementations of the Post Office Protocol (POP3). R. Nelson. June 1996. (Format: TXT=2325 bytes) (Updates RFC1939) (Status: INFORMATIONAL) 1985 SMTP Service Extension for Remote Message Queue Starting. J. DeWinter. August 1996. (Format: TXT=14815 bytes) (Status: PROPOSED STANDARD) 2015 MIME Security with Pretty Good Privacy (PGP). M. Elkins. October 1996. (Format: TXT=14223 bytes) (Status: PROPOSED STANDARD) 2016 Uniform Resource Agents (URAs). L. Daigle, P. Deutsch, B. Heelan, C. Alpaugh, M. Maclachlan. October 1996. (Format: TXT=38355 bytes) (Status: EXPERIMENTAL) 2033 Local Mail Transfer Protocol. J. Myers. October 1996. (Format: TXT=14711 bytes) (Status: INFORMATIONAL) 2034 SMTP Service Extension for Returning Enhanced Error Codes. N. Freed. October 1996. (Format: TXT=10460 bytes) (Status: PROPOSED STANDARD) 2045 Multipurpose Internet Mail Extensions (MIME) Part One: Format of Internet Message Bodies. N.Freed & N. Borenstein. November 1996. (Format: TXT=72932 bytes) (Obsoletes RFC1521, RFC1522, RFC15900) (Updated by RFC2184, RFC2231) (Status: DRAFT STANDARD) 2046 Multipurpose Internet Mail Extensions (MIME), Part Two: Media Types. N. Freed and N. Borenstein. November 1996. (Format: TXT=105854 bytes) (Obsoletes RFC1521, RFC1522, RFC1590) (Status: DRAFT STANDARD) 2047 MIME (Multipurpose Internet Mail Extensions), Part Three: Message Header Extensions for Non-ASCII Text. K. Moore. November 1996. (Format: TXT=3326T2 bytes) (Obsoletes RFC1521, RFC1522, RFC1590) (Updated by RFC2184, RFC2231) (Status: DRAFT STANDARD) 2048 Multipurpose Internet Mail Extensions (MIME), Part Four: Registration Procedures. N.Freed, J. Klensin, and J. Postel. November 1996. (Format: TXT=45033 bytes) (Obsoletes RFC1521, RFC1522, RFC1590) (Also BCP0013) (Status: BEST CURRENT PRACTICE) 2049 Multipurpose Internet Mail Extensions (MIME), Part Five: Conformance Criteria and Examples. N. Freed & N. Borenstein. November 1996. (Format: TXT=51207 bytes) (Obsoletes RFC1521, RFC1522, RFC1590) (Status: DRAFT STANDARD) 2060 Internet Message Access Protocol, Version 4rev1. M. Crispin. December 1996. (Format: TXT=166513 bytes) (Obsoletes RFC1730) (Status: PROPOSED STANDARD) 2061 IMPA4 Compatibility With IMAP2BIS. M. Crispin. December 1996. (Format: TXT=5867 bytes) (Obsoletes RFC1730) (Status: INFORMATIONAL) 2062 Internet Message Access ProtocolObsolete Syntax. M. Crispin. December 1996. (Format: TXT=14222 bytes) (Status: PROPOSED STANDARD) 2076 Common Internet Message Headers. J.Palme. February 1997. (Format: TXT=47639 bytes) (Status: INFORMATIONAL)
407
2077 The Model Primary Content-type for Multipurpose Internet Mail Extensions. S. Nelson, C. Parks, Mitra. January 1997. (Format: TXT=30158 bytes) (Status: PROPOSED STANDARD) 2086 IMAP4 ACL Extension. J. Myers. January 1997. (Format: TXT=13925 bytes) (Status: PROPOSED STANDARD) 2087 IMAP4 QUOTA Extension. J. Myers. January 1997. (Format: TXT=8524 bytes) (Status: PROPOSED STANDARD) 2088 IMAP4 Non-synchronizing literals. J. Myers. January 1997. (Format: TXT=4052 bytes) (Status: PROPOSED STANDARD) 2095 IMAP/POP Authorize Extension for Simple Challenge/Response. J. Klensin, R. Catoe, and P. Krumviede. January 1997. (Format: TXT=10446 bytes) (Obsoleted by RFC2195) (Status: PROPOSED STANDARD) 2110 MIME Encapsulation of Aggregate Documents Such As HTML (MHTML). J. Palme and A. Hopmann. March 1997. (Format: TXT=41961 bytes) (Status: PROPOSED STANDARD) 2112 The MIME Multipart/Related Content-type. E. Levinson. February 1997. (Format: TXT=17052 bytes) (Obsoletes RFC1872) (Obsoleted by RFC2387) (Status: PROPOSED STANDARD) 2142 Mailbox Names for Common Services, Roles, and Functions.D. Crocker. May 1997. (Format: TXT=12195 bytes) (Status: PROPOSED STANDARD) 2152 UTF-7 A Mail-Safe Transformation Format of Unicode. D. Goldsmith, M. Davis. May 1997. (Format: TXT=28065 bytes) (Obsoletes RFC1642) (Status: INFORMATIONAL) 2156 MIXER (Mime Internet X.400 Enhanced Relay): Mapping between X.400 and RFC 822/MIME. S. Kille. January 1998. (Format: TXT=280385 bytes) (Obsoletes RFC0987, RFC1026, RFC1138, RFC1148, RFC1327, RFC1495) (Updates RFC0822) (Status: PROPOSED STANDARDS) 2157 Mapping between X.400 and RFC-822/MIME Message Bodies. H. Alvestrand. January 1998. (Format: TXT=92554 bytes) (Status: PROPOSED STANDARD) 2158 X.400 Image Body Parts. H. Alvestrand. January 1998. (Format: TXT=5547 bytes) (Status: PROPOSED STANDARD) 2160 Carrying PostScript in X.400 and MIME. H. Alvestrand. January 1998. (Format: TXT=7059 bytes) (Status: PROPOSED STANDARD) 2161 A MIME Body Part for ODA. H. Alvestrand. January 1998. (Format: TXT=8009 bytes) (Status: EXPERIMENTAL) 2162 MaXIM-11Mapping Between X.400/Internet Mail and Mail-11 Mail. C. Allocchio. January 1998. (Format: TXT=58553 bytes) (Obsoletes RFC1405) (Status: EXPERIMENTAL)
408
TCP/IP PRIMER PLUS
2163 Using the Internet DNS to Distribute MIXER Conformant Global Address Mapping (MCGAM). C. Allocchio. January 1998. (Format: TXT=58789 bytes) (Obsoletes RFC1664) (Status: PROPOSED STANDARD) 2164 Use of the X.500/LDAP Directory to Support MIXER Address Mapping. S. Kille. January 1998. (Format: TXT=16701 bytes) (Obsoletes RFC1838) (Status: PROPOSED STANDARD) 2177 IMAP4 IDLE command. B. Leiba. June 1997. (Format: TXT=6770 bytes) (Status: PROPOSED STANDARD) 2180 IMAP4 Multi-accessed Mailbox Practice. M.Gahrns. July 1997. (Format: TXT=24750 bytes) (Status: INFORMATIONAL) 2184 MIME Parameter Value and Encoded Word Extensions: Character Sets, Languages, and Continuations. N. Freed and K. Moore. August 1997. (Format:TXT=17635 bytes) (Obsoletes RFC2184) (Obsoleted by RFC2184, RFC2231) (Updates RFC2045, RFC2047, RFC2183) (Status: PROPOSED STANDARD) 2192 IMAP URL Scheme. C. Newman. September 1997. (Format: TXT=31426 bytes) (Status: PROPOSED STANDARD) 2193 IMAP4 Mailbox Referrals. M. Gahrns. September 1997. (Format: TXT=16248 bytes) (Status: PROPOSED STANDARD) 2195 IMAP/POP Authorize Extension for Simple Challenge/Response. J. Klensin, R. Catoe, P. Krumviede. September 1997. (Format: TXT=10468 bytes) (Obsoletes RFC2095) (Status: PROPOSED STANDARD) 2197 SMTP Service Extension for Command Pipelining. N. Freed. September 1997. (Format: TXT=15003 bytes) (Obsoletes RFC1854) (Status: DRAFT STANDARD) 2220 The Application/MARC Content-type. R. Guenther. October 1997. (Format: TXT=7025 bytes) (Status: INFORMATIONAL) 2221 IMAP4 Login Referrals. M. Gahrns. October 1997. (Format: TXT=9251 bytes) (Status: PROPOSED STANDARD) 2231 MIME Parameter Value and Encoded Word Extensions: Character Sets, Languages, and Continuations. N. Freed and K. Moore. November 1997. (Format: TXT=19280 bytes) (Obsoletes RFC2184) (Updates RFC2045, RFC2047 RFC2183) (Status: PROPOSED STANDARD) 2298 An Extensible Message Format for Message Disposition Notifications. R. Fajman. March 1998. (Format: TXT=62059 bytes) (Status: PROPOSED STANDARD) 2302 Tag Image File Format (TIFF)Image/tiff MIME Sub-type Registration. G. Parsons, J. Rafferty, S. Zilles. March 1998. (Format: TXT=14375 bytes) (Status: PROPOSED STANDARD)
409
2311 S/MIME Version 2 Message Specification. S. Dusse, P. Hoffman, B. Ramsdell, L. Lundblade, L. Repka. March 1998. (Format: TXT=7091 bytes) (Status: INFORMATIONAL) 2312 S/MIME Version 2 Certification Handling. S. Dusse, P. Hofffman, B. Ramsdell, and J. Weinstein. March 1998. (Format: TXT=39829 bytes) 2318 The Text/CSS Media Type. H. Lie, B. Bos, and C. Lilley. March 1998. (Format: TXT=7819 bytes) (Status: INFORMATIONAL) 2342 IMAP4 Namespace. M. Gahrns and C. Newman. May 1998. (Format: TXT=19489 bytes) (Status: PROPOSED STANDARD) 2359 IMAP4 UIDPLUS Extension. J. Myers. June 1998. (Format: TXT=10862 bytes) (Status: PROPOSED STANDARD) 2384 POP URL Scheme. R. Gellens. August 1998. Format: TXT=13649 bytes) (Status: PROPOSED STANDARD) 2387 The MIME Multipart/Related Content-type. E. Levinson. August 1998. (Format: TXT=18864 bytes) (Obsoletes RFC2112) (Status: PROPOSED STANDARD) 2424 ContentDuration MIME Header Definition. G. Vaudreuil and G. Parsons. September 1998. (Format: TXT=7116 bytes) (Status: PROPOSED STANDARD) 2425 A MIME Content-type for Directory Information. T. Howes, M. Smith, and F Dawson. . September 1998. (Format: TXT=64478 bytes) (Status: PROPOSED STANDARD) 2426 vCard MIME Directory Profile. F Dawson and T. Howes. September 1998. (Format: . TXT=74746 bytes) (Status: PROPOSED STANDARD) 2442 The Batch SMTP Media Type. N. Freed, D. Newman, H. Belissen, and M. Hoy. November 1998. (Format: TXT=18384 bytes) (Status: INFORMATIONAL) 2449 POP3 Extension Mechanism. R. Gellens, C. Newman, and L. Lundblade. November 1998. (Format: TXT=36017 bytes) (Updates RFC1939) (Status: PROPOSED STANDARD) 2476 Message Submission. R. Gellens and H. Klensin. December 1998. (Format: TXT=30050 bytes) (Status: PROPOSED STANDARD) 2480 Gateways and MIME Security Multiparts. N. Freed. January 1999. (Format: TXT=11751 bytes) (Status: PROPOSED STANDARD) 2487 SMTP Service Extension for Secure SMTP Over TLS. P. Hoffman. January 1999. (Format: TXT=15120 bytes) (Status: PROPOSED STANDARD) 2503 MIME Types for Use with the ISO ILL Protocol. R. Moulton and M. Needleman. February 1999. (Format: TXT=9078 bytes) (Status: INFORMATIONAL) 2505 Anti-Spam Recommendations for SMTP MTAs. G.Lindberg. February 1999. (Format: TXT=53597 bytes) (Also BCP0030) (Status: BEST CURRENT PRACTICES)
410
TCP/IP PRIMER PLUS
2524 Nedas Efficient Mail Submission and Delivery (EMSD) Protocol Specification Version 1.3. M. Banan. February 1999. (Format: TXT=153171 bytes) (Status: INFORMATIONAL) 2554 SMTP Service Extension for Authentication. J. Meyers. March 1999. (Format: TXT=20534 bytes) (Status: PROPOSED STANDARD) 2557 MIME Encapsulation of Aggregate Documents Such As HTML (MHTML). J. Palme, A. Hopmann, and N. Shelness. March 1999. (Format: TXT=61854 bytes) (Obsoletes RFC2110) (Status: PROPOSED STANDARD) 2586 The Audio/L16 MIME 2595 Using TLS with IMAP, POP3, and ACAP 2632 S/MIME Version 3 Certificate Handling 2633 S/MIME Version 3 Message Specification 2634 Enhanced Security Service for S/MIME 2645 On-demand Mail Relay (ODMR) SMTP With Dynamic IP Addresses 2646 The Text/Plain Format Parameter 2683 IMAP4 Implementation Recommendations
Chapter 14: Name Resolution

752 Universal Host Table 756 NIC Name Servera Datagram-based Information Utility 799 Internet Name Domains 811 Hostname Server 819 Domain Naming Convention for Internet User Applications 830 Distributed System for Internet Name Service 881 Domain Names Plan and Schedule 882 Domain Names: Concepts and Facilities 883 Domain Names: Implementation Specification 897 Domain Name System Implementation ScheduleRevised 920 Domain Requirements 921 Domain Name System Implementation ScheduleRevised 953 Hostname Server
411
973 Domain System Changes and Observations 1001 ProtocolStandard for a NetBIOS Service on a TCP/UDP Transport: Concepts and Methods. NetBIOS Working Group. Defense Advanced Research Projects Agency, Internet Activities Board, End-to-End Services Task Force. Mar-01-1987. (Format: TXT=158437 bytes) (Status: STANDARD) 1002 Protocol Standard for a NetBIOS Service on a TCP/UDP Transport: Detailed Specifications. NetBIOS Working Group. Defense Advanced Research Projects Agency, Internet Activities Board, End-to-End Services Task Force. Mar-01-1987. (Format: TXT=170262 bytes) (Status: STANDARD) 1031 MILNET Name Domain Transition. W. D. Lazear. Nov-01-1987. (Format: TXT=20137 bytes) (Status: UNKNOWN) 1032 Domain Administrators Guide. M. K. Stahl. Nov-01-1987. (Format: TXT=29454 bytes) (Status: UNKNOWN) 1033 Domain Administrators Operations Guide. M. Lottor. Nov-01-1987. (Format: TXT=37263 bytes) (Status: UNKNOWN) 1034 Domain NamesConcepts and Facilities. P. V. Mockapetris. Nov-01-1987. (Format: TXT=129180 bytes) (Obsoletes RFC0973, RFC0882, RFC0883) (Obsoleted by RFC1065, RFC2308) (Updated by RFC1101, RFC1183, RFC1348, RFC1876, RFC1982, RFC2065, RFC2181, RFC2308) (Status: STANDARD) 1035 Domain Administrators Guide. M. K. Stahl. Nov-01-1987. (Format: TXT=29454 bytes) (Status: UNKNOWN) 1036 Domain Administrators Guide. M. Lottor. Nov-01-1987. (Format: TXT=37263 bytes) (Status: UNKNOWN) 1037 Domain NamesConcepts and Facilities. P. V. Mockapetris. Nov-01-1987. (Format: TXT=129180 bytes) (Obsoletes RFC0973, RFC0882, RFC0883) (Obsoleted by RFC1065, RFC2308) (Updated by RFC1101, RFC1183, RFC1348, RFC1876, RFC1982, RFC1995, RFC1996, RFC2065, RFC2181, RFC2136, RFC2137, RFC2308) (Status: STANDARD) 1038 Domain NamesImplementation and Specification. P. V. Mockapetris. Nov-01-1987. (Format: TXT=125626 bytes) (Obsoletes RFC0973, RFC0882, RFC0883) (Updated by RFC1101, RFC1183, RFC1348, RFC1876, RFC1982, RFC1995, RFC1996, RFC2065, RFC2181, RFC2136, RFC2137, RFC2308) (Status: STANDARD) 1101 DNS Encoding of Network Names and Other Types. P. V. Mockapetris. Apr-01-1989. (Format: TXT=28677 bytes) (Updates RFC1034, RFC1035) (Status: UNKNOWN) 1183 New DNS RR Definitions. C. F Everhart, L. A. Mamakos, R. Ullmann, and P. V. . Mockapetris. Oct-01-1990. (Format: TXT=23788 bytes) (Updates RFC1034,RFC1035) (Status: EXPERIMENTAL)
412
TCP/IP PRIMER PLUS
1348 DNS NSAP Resource Records. B. Manning. July 1992. (Format: TXT=6871 bytes) (Obsoleted by RFC1637) (Updates RFC1034, RFC1035) (Updated by RFC1637) (Status: EXPERIMENTAL) 1383 An Experiment in DNS-based IP Routing. C. Huitema. December 1992. (Format: TXT=32680 bytes) (Status: EXPERIMENTAL) 1386 The US Domain. A. Cooper and J. Postel. December 1992. (Format: TXT=62310 bytes) (Obsoleted by RFC1480) (Status: INFORMATIONAL) 1394 Relationship of Telex Answerback Codes to Internet Domains. P. Robinson. January 1993. (Format: TXT=43776 bytes) (Status: INFORMATIONAL) 1464 Using the Domain Name System to Store Arbitrary String Attributes. R. Rosenbaum. May 1993. (Format: TXT=7953 bytes) (Status: EXPERIMENTAL) 1480 The US Domain. A. Cooper and J. Postel. June 1993. (Format: TXT=100556 bytes) (Obsoletes RFC1386) (Status: INFORMATIONAL) 1535 A Security Problem and Proposed Correction With Widely Deployed DNS Software. E. Gavron. October 1993. (Format: TXT=9722 bytes) (Status: INFORMATIONAL) 1536 Common DNS Implementation Errors and Suggested Fixes. A.Kumar, J. Postel, C. Neuman, P. Danzig, and S. Miller. October 1993. (Format: TXT=25476 bytes) (Status: INFORMATIONAL) 1537 Common DNS Operational and Configuration Errors. P. Beertema. October 1993. (Format: TXT=19825 bytes) (Obsoleted by RFC1912) (Status: INFORMATIONAL) 1591 Domain Name System Structure and Delegation. J. Postel. March 1994. (Format: TXT=16481 bytes) (Status: INFORMATIONAL) 1637 DNSAP Resource Records. B. Manning and R. Colella. June 1994. (Format: TXT=21768 bytes) (Obsoletes RFC1348) (Obsoleted by RFC1706) (Updates RFC1348) (Status: EXPERIMENTAL) 1706 DNS NSAP Resource Records. B. Manning and R. Colella. October 1994. (Format: TXT=19721 bytes) (Obsoletes RFC1637) (Status: INFORMATIONAL) 1712 DNS Encoding of Graphical Location. C. Farrell, M. Schulze, S. Pleitner, and D. Baldoni. November 1994. (Format: TXT=13237) 1713 Tools for DNS Debugging. A. Romao. November 1994. (Format: TXT=33500 bytes) (Also FYI10027) (Status: INFORMATIONAL) 1794 DNS Support for Load Balancing. T. Brisco. April 1995. (Format: TXT=15494 bytes) (Status: INFORMATIONAL) 1876 A Means for Expressing Location Information in the Domain Name System. C. Davis, P. Vixie, T. Goodwin, and I. Dickinson. January 1996. (Format: TXT=29631 bytes) (Updates RFC1034, RFC1035) (Status: EXPERIMENTAL)
413
1912 Common DNS Operational and Configuration Errors. D. Barr. February 1996. (Format: TXT=38252 bytes) (Obsoletes RFC1537) (Status: INFORMATIONAL) 1982 Serial Number Arithmatic. R. Elz and R. Bush. August 1996. (Format: TXT=14440 bytes) (Updates RFC1034, RFC1035) (Status: PROPOSED STANDARD) 1995 Incremental Zone Transfer in DNS. M. Ohta. August 1996. (Format: TXT=16810 bytes) (Updates RFC1035) (Status: PROPOSED STANDARD) 1996 A Mechanism for Prompt Notification of Zone Changes (DNS NOTIFY). P. Vixie. August 1996. (Format: TXT=15247 bytes) (Updates RFC1035) (Status: PROPOSED STANDARD) 2010 Operational Criteria for Root Name Servers. B. Manning and P. Vixie. October 1996. (Format: TXT=14870 bytes) (Status: INFORMATIONAL) 2052 A DNS RR for Specifying the Location of Services (DNS SRV). A. Gulbrandensen, P. Vixie. October 1996. (Format: TXT19257 bytes) (Status: EXPERIMENTAL) 2065 Domain Name System Security Extensions. D. Eastlake, 3rd Edition. C. Kaufman. January 1997. (Format: TXT=97718 bytes) (Updates RFC1034, RFC1035) (Status: PROPOSED STANDARD) 2136 Dynamic Updates in the Domain Name System (DNS UPDATE). P. Vixie, Ed., S. Thomson, Y. Rekhter, J. Bound. April 1997. (Format: TXT=56354 bytes) (Updates RFC1035) (Status: PROPOSED STANDARD) 2137 Secure Domain Name System Dynamic Update. D. Eastlake. April 1997. (Format: TXT=24824 bytes) (Updates RFC1035) (Status: PROPOSED STANDARD) 2181 Clarification of DNS Specification. R. Elz and R. Bush. July 1997. (Format: TXT=36989 bytes) (Updates RFC1034, RFC1035, RFC1123) (Status: PROPOSED STANDARD) 2182 Selection and Operation for Secondary DNS Servers. R. Elz, R. Bush, S. Bradner, and M. Patton. July 1997. (Format: TXT=27456 bytes) (Also BCP0016) (Status: BEST CURRENT PRACTICE) 2219 Use of DNS Aliases for Network Services. M. Hamilton and R. Wright. October 1997. (Format: TXT=17858 bytes) (Also BCP0017) (Status: BEST CURRENT PRACTICE) 2230 Key Exchange Delegation Record for the DNS. R. Atkinson. October 1997. (Format: TXT=25563 bytes) (Status: INFORMATIONAL) 2240 A Legal Basis for Domain Name Allocation. O. Vaughan. November 1997. (Format: TXT=13602 bytes) (Obsoleted by RFC2352) (Status: INFORMATIONAL) 2308 Negative Caching of DNS Queries (DNS NCACHE). M. Andrews. March 1998. (Format: TXT=41428 bytes) (Obsoletes RFC1034) (Updates RFC1034, RFC1035) (Status: PROPOSED STANDARD) 2317 Classless IN-ADDR.ARPA Delegation. H. Eidnes, G. de Groot, and P. Vixie. March 1998. (Format: TXT=17744 bytes) (Also BCP0020) (Status: BEST CURRENT PRACTICE)
414
TCP/IP PRIMER PLUS
2517 Building Directories from DNS: Experiences from WWWSeeker. R. Moats and R. Huber. February 1999. (Format: TXT=14001 bytes) (Status: INFORMATIONAL) 2535 Domain Name System Security Extensions. D. Eastlake. March 1999. (Format: TXT=110958 bytes) (Updates RFC2181, RFC1035, RFC1034) (Status: PROPOSED STANDARD) 2539 Storage of Diffie-Hellman Keys in the Domain Name System (DNS). D. Eastlake. March 1999. (Format: TXT=21049 bytes) (Status: PROPOSED STANDARD) 2540 Detached Domain Name System (DNS) Information. D. Eastlake. March 1999. (Format: TXT=12546 bytes) (Status: EXPERIMENTAL) 2541 DNS Security Operational Considerations. D. Eastlake. March 1999. (Format: TXT=14498 bytes) (Status: INFORMATIONAL) 2606 Reserved Top-level DNS Names 2671 Extension Mechanisms for DNS (EDNSO) 2672 Non-terminal DNS Name Redirection 2673 Binary Labels in the Domain Name System
Chapter 15: Hypertext Transfer Protocol (HTTP)

1009 Requirements for Internet Gateways. R. T. Braden and J. Postel. Jun-01-1987. (Format: TXT=128173 bytes) (Status: HISTORIC) 1945 Hypertext Transfer ProtocolHTTP/1.0. T. Berners-Lee, R. Fielding, and H. Frystuk. May 1996. (Format: TXT=137582 bytes) (Status: INFORMATIONAL) 2068 Hypertext Transfer ProtocolHTTP/1.1 R.Fielding, J. Gettys, J. Mogul, H. Frystyk, and T. Berners-Lee. January 1997. (Format: TXT=378114 bytes) (Status: PROPOSED STANDARD) 2069 HTTP Authentication: Basic and Digest Access Authentication. J.Franks, P.Hallam-Baker, J. Hostetler, P. Leach, A. Luotonen, E. Sink, L. Stewart. January 1997. (Format: TXT=41733 bytes) (Status: PROPOSED STANDARD) 2109 HTTP State Management Mechanism. D. Kristol and L.Montulli. February 1997. (Format: TXT=43469 bytes) (Obsoletes RFC1920) (Status: PROPOSED STANDARD) 2145 Use and Interpretation of HTTP Version Numbers. J. C. Mogul, R. Fielding, J. Gettys, and H. Frystuk. May 1997. (Format: TXT=13659 bytes) (Status: INFORMATIONAL) 2169 A Trivial Convention for using HTTP in URN Resolution. R. Daniel. June 1997. (Format: TXT=17763 bytes) (Status: EXPERIMENTAL)
415
2227 Simple Hit Metering and Usage Limiting for HTTP. J. Mogul and P. Leach. October 1997. (Format: TXT=85127 bytes) (Status: PROPOSED STANDARD) 2295 Transparent Content Negotiation in HTTP. K. Holtman and A. Mutz. March 1998. (Format: TXT=125130 bytes) (Status: EXPERIMENTAL) 2518 HTTP Extensions for Distributed AuthoringWEBDAV. Y. Goland, E. Whitehead, A. Faizi, S. Carter, and D. Jensen. February 1999. (Format: TXT=202829 bytes) (Status: PROPOSED STANDARD) 2616 Hypertext Transfer ProtocolHTTP/1.1 2660 The Secure Hypertsext Transfer Protocol
Chapter 16: Trivial File Transfer Protocol (TFTP)

906 Bootstrap Loading Using TFTP 1782 TFTP Option Extension. G. Malkin and A. Harkin. March 1995. (Format: TXT=11508 bytes) (Obsoleted by RFC2347) (Updates RFC1350) 1783 TFTP Blocksize Option. G. Malkin and A. Harkin. March 1995. (Format: TXT=7814 bytes) (Obsoleted by RFC2348) (Updates RFC1350) (Updated by RFC1350) (Status: PROPOSED STANDARD) 1784 TFTP Timeout Interval and Transfer Size Option. G. Malkin and A. Harkin. March 1995. (Format: TXT=6106 bytes) (Obsoleted by RFC2349) (Updates RFC1350) (Status: PROPOSED STANDARD) 1785 TFTP Option Negotiation Analysis. G. Malkin and A. Harkin. March 1995. (Format: TXT=3354 bytes) (Updates RFC1350) (Status: INFORMATIONAL) 2090 TFTP Multicast Option. A. Emberson. February 1997. (Format: TXT=11857 bytes) (Status: EXPERIMENTAL) 2347 TFTP Option Extension. G. Malkin and A. Harkin. May 1998. (Format: TXT=13060 bytes) (Obsoletes RFC 1782) (Updates RFC1350) (Status: DRAFT STANDARD) 2348 TFTP Blocksize Option. G. Malkin and A. Harkin. May 1998. (Format: TXT=9515 bytes) (Obsoletes RFC1783) (Updates RFC1350) (Status: DRAFT STANDARD) 2349 TFTP Timeout Interval and Transfer Size Option. G. Malkin and A. Harkin. May 1998. (Format: TXT=7848 bytes) (Obsoletes RFC1784) (Updates RFC1350) (Status: DRAFT STANDARD)
416
TCP/IP PRIMER PLUS
Chapter 17: Simple Network Management Protocol (SNMP)

1067 Simple Network Management Protocol (SNMP). J.D. Case, M. Fedor, M. L. Schoffstall, and J. Davin. Aug-01-1988. (Format: TXT=69592 bytes) (Obsoleted by RFC1098) (Status: UNKNOWN) 1089 SNMP Over Ethernet. M. L. Schoffstall, C. Davin, M. Fedor, and J. D. Case. Feb-011989. (Format: TXT=4458 bytes) (Status: UNKNOWN) 1098 Simple Layer Management Protocol (SNMP). J. D. Case, M. Fedor, M. L. Schoffstall, and C. Davin. Apr-01-1989. (Format: TXT=71563 bytes) (Obsoleted by RFC1157) (Status: UNKNOWN) 1157 Simple Network Management Protocol (SNMP). J. D. Case, M. Fedor, M. L. Schoffstall, and C. Davin. May-01-1990. (Format: TXT=74894 bytes) (Obsoletes RFC1066) (Status: HISTORIC) 1161 SNMP Over OSI. M. T. Rose. Jun-01-1990. (Format: TXT=16036 bytes) (Obsoletes by RFC1418) (Status: EXPERIMENTAL) 1187 Bulk Table Retrieval for the SNMP. M. T. Rose, K. McCloghrie, and J. R. Davin. Oct-011990. (Format: TXT=27220 bytes) (Status: EXPERIMENTAL) 1212 Concise MIB Definitions. M. T. Rose, K. McCloghrie. Mar-01-1991. (Format: TXT=43579 bytes) (Status: STANDARD) 1215 Convention for Defining Traps to Use With the SNMP. M. T. Rose. Mar-01-1991. (Format: TXT=19336 bytes) (Status: INFORMATIONAL) 1227 SNMP MUX Protocol and MIB. M. T. Rose. May-01-1991. (Format: TXT=25868 bytes) (Status: HISTORIC) 1228 SNMP-DPI: Simple Network Management Protocol Distributed Program Interface, Version 2.0. G. Carpenter and B. Wijnen. May-01-1991. (Format: TXT=96972 bytes) (Obsoleted by RFC1592) (Status: EXERIMENTAL) 1229 Extensions to the Generic-interface MIB. K. McCloghrie. May-01-1991. (Format: TXT=36022 bytes) (Obsoleted by RFC1573) (Updated by RFC1239) (Status: PROPOSED STANDARD) 1239 Reassignment of Experimental MIBs to Standard MIBs. J. K. Reynolds. Jun-01-1991. (Format: TXT=3656 bytes) (Updates RFC1229, RFC1230, RFC1231, RFC1232, RFC1233) (Status: PROPOSED STANDARD) 1270 SNMP Communication Services. F Kastenholz. Oct-01-1991. (Format: TXT=26167 . bytes) (Status: INFORMATIONAL) 1283 SNMP Over OSI. M. Rose. December 1991. (Format: TXT=16857 bytes) (Obsoleted by RFC1418) (Status: EXPERIMENTAL)
417
1298 SNMP Over IPX. R. Wormley, S. Bostock. February 1992. (Format: TXT=7878 bytes) (Obsoleted by RFC1420) (Status: INFORMATIONAL) 1303 A Convention for Describing SNMP-based Agents. K. McCloghrie and M. Rose. February 1992. (Format: TXT=22915 bytes) (Also RFC1155, RFC1212, RFC1213, RFC1157) (Status: INFORMATIONAL) 1351 SNMP Administrative Model. J. Davin, J. Galvin, and K. McCloghrie. July 1992. (Format: TXT=80721 bytes) (Status: PROPOSED STANDARD) 1352 SNMP Security Protocols. J. Galvin, K. McClghrie, and J. Davin. July 1992. (Format: TXT=80721 bytes) (Status: PROPOSED STANDARD) 1353 Definitions of Managed Objects for Administration of SNMP Parties. K. McCloghrie, J. Davin, and J. Galvin. July 1992. (Format: TXT=59556 bytes) (Status: PROPOSED STANDARD) 1369 Implementation Notes and Experience for the Internet Ethernet MIB. F Kastenholz. . October 1992. (Format: TXT=13921 bytes) (Status: PROPOSED STANDARD) 1418 SNMP Over OSI. M. Rose. March 1993. (Format: TXT=7721 bytes) (Obsoletes RFC1161, RFC1283) (Status: PROPOSED STANDARD) 1419 SNMP Over AppleTalk. G. Minshall and M. Ritter. March 1993. (Format: TXT=16470 bytes) (Status: PROPOSED STANDARD) 1420 SNMP Over IPX. S. Bostock. March 1993. (Format: TXT=6762 bytes) (Obsoletes RFC1298) (Status: PROPOSED STANDARD) 1441 Introduction to Version 2 of the Internet-standard Network Management Framework. J.Case, K. McCloghrie, M. Rose, and S. Waldbusser. April 1993. (Format: TXT=25386 bytes) (Status: PROPOSED STANDARD) 1442 Structure of Management Information for Version 2 of the Simple Network Management Protocol (SMIv2). J. Case, K. McCloghrie, M. Rose, and S. Waldbusser. April 1993. (Format: TXT=95779 bytes) (Obsoleted by RFC1902) (Status: PROPOSED STANDARD) 1443 Textual Conventions for Version 2 of the Simple Network Management Protocol (SMIv2). J. Case, K. McCloghrie, M. Rose, and S. Waldbusser. April 1993. (Format: TXT=60947 bytes) (Obsoleted by RFC1903) (Status: PROPOSED STANDARD) 1444 Conformance Statements for Version 2 of the Simple Network Management Protocol (SMIv2). J. Case, K. McCloghrie, M. Rose, and S. Waldbusser. April 1993. (Format: TXT=57744 bytes) (Obsoleted by RFC1904) (Status: PROPOSED STANDARD) 1445 Administrative Model for Version 2 of the Simple Network Management Protocol (SNMPv2) 1446 Security Protocols for Version 2 of the Simple Network Management Protocol (SNMPv2). J.Galvin and K. McCloghrie, M. Rose, and S. Waldbusser. April 1993. (Format: TXT=99443 bytes) (Status: HISTORIC)
418
TCP/IP PRIMER PLUS
1448 Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2). J. Case, K. McCloghrie, M. Rose, and S. Waldbusser. April 1993. (Format: TXT=74224 bytes) (Obsoleted by RFC1905) (Status: PROPOSED STANDARD) 1449 Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2). J. Case, K. McCloghrie, M. Rose, and S. Waldbusser. April 1993. (Format: TXT=41161 bytes) (Obsoleted by RFC1906) (Status: PROPOSED STANDARD) 1452 Coexistence Between Version 1 and Version 2 of the Internet-standard Network Management Framework. J. Case, K. McCloghrie, M. Rose, and S. Waldbusser. April 1993. (Format: TXT=32176 bytes) (Obsoleted by RFC1908) (Status: PROPOSED STANDARD) 1503 Algorithms for Automating Administration in SNMPv2 Managers. K. McCloghrie and M. Rose. August 1993. (Format: TXT=33542 bytes) (Status: INFORMATIONAL) 1856 The Opstat Client-Server Model for Statistical Retrieval. H. Clark. October 1995. (Format: TXT=29954 bytes)(Status: INFORMATIONAL) 1901 Introduction for Community-based SNMPv2. SNMPv2 Working Group, J.Case, K. McCloghrie, M. Rose, and S. Waldbusser. January 1996. (Format: TXT=15903 bytes) (Status: EXPERIMENTAL) 1902 Structure of Management Information for Version 2 of the Simple Network Management Protocol (SMIv2). SNMPv2 Working Group, J.Case, K. McCloghrie, M. Rose, and S. Waldbusser. January 1996. (Format: TXT=77453 bytes) (Obsoletes RFC1442) (Status: DRAFT STANDARD) 1903 Textual Conventions for Version 2 of the Simple Network Management Protocol (SMIv2). SNMPv2 Working Group, J. Case, K. McCloghrie, M. Rose, and S. Waldbusser. January 1996. (Format: TXT=52652 bytes) (Obsoletes RFC1443) (Status: DRAFT STANDARD) 1904 Conformance Statements for Version 2 of the Simple Network Management Protocol (SMIv2). SNMPv2 Working Group, J.Case, K. McCloghrie, M. Rose, and S. Waldbusser. January 1996. (Format: TXT=47083 bytes) (Obsoletes RFCE1444) (Status: DRAFT STANDARD) 1905 Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2). SNMPv2 Working Group, J.Case, K. McCloghrie, M. Rose, and S. Waldbusser. January 1996. (Format: TXT=55526 bytes) (Obsoletes RFC1448) (Status: DRAFT STANDARD) 1906 Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2). SNMPv2 Working Group, J.Case, K. McCloghrie, M. Rose, and S. Waldbusser. January 1996. (Format: TXT=27465 bytes) (Obsoletes RFC1449) (Status: DRAFT STANDARD)
419
1908 Coexistence between Version 1 and Version 2 of the Internet-standard Network Management Framework. SNMPv2 Working Group, J. Case, K. McCloghrie, M. Rose, and S. Waldbusser. January 1996. (Format: TXT=21463 bytes) (Obsoletes RFC1452) (Status: DRAFT STANDARD) 1909 An Administrative Infrastructure for SNMPv2. K. McCloghrie. February 1996. (Format: TXT=45773 bytes) (Status: EXPERIMENTAL) 1910 User-based Security Model for SNMPv2. G. Waters. February 1996. (Format: TXT=98252 bytes) (Status: EXPERIMENTAL) 2011 SNMPv2 Management Information Base for the Internet Protocol Using SMIv2. K. McCloghrie. November 1996. (Format: TXT=31168 bytes) (Updates RFC1213) (Status PROPOSED STANDARD) 2012 SNMPv2 Management Information Base for the Transmission Control Protocol using SMIv2. K. McCloghrie. November 1996. (Format: TXT=16792 bytes) (Updates RFC1213) (Status PROPOSED STANDARD) 2013 SNMPv2 Management Information Base for the User Datagram Protocol using SMIv2. K. McCloghrie. November 1996. (Format: TXT=9333 bytes) (Updates RFC1213) (Status PROPOSED STANDARD) 2039 Applicability for Standards Track MIBs to Management of World Wide Web Servers. C. Kalbfleisch. November 1996. (Format: TXT=31966 bytes) (Status: INFORMATIONAL) 2089 V2ToV1 Mapping SNMPv2 Onto SNMPv1 Within a Bilingual SNMP Agent. B. Winjnene, D. Levi. January 1997. (Format: TXT=23814 bytes) 2107 Ascend Tunnel Management ProtocolATMP. K. Hamzeh. February 1997. (Format: TXT=44300 bytes) (Status: INFORMATIONAL) 2257 Agent Extensibility (AgentX) Protocol Version 1. M. Daniele, B. Wijnen, D. Francisco. January 1998. (Format: TXT=177452 bytes) (Status: PROPOSED STANDARD) 2261 An Architecture for Describing SNMP Management Frameworks. D. Harrington, R. Presuhn, B. Wijnen. January 1998. (Format: TXT=128036 bytes) (Obsoleted by RFC2271) (Status: PROPOSED STANDARD) 2262 Message Processing and Dispatching for the Simple Network Management Protocol (SNMP). J. Case, D. Harrington, R. Presuhn, B. Wijnen. January 1998. (Format: TXT=88254 bytes) (Obsoleted by RFC2272) (Status: PROPOSED STANDARD) 2263 SNMP Applications. D. Levi, P. Meyer, and B. Stewart. January 1998. (Format: TXT=143493 bytes) (Obsoleted by RFC2273) (Status: PROPOSED STANDARD) 2264 User-based Security Model (USM) for Version 3 of the Simple Network Management Protocol (SNMPv3). U. Blumenthal and B. Wijnen. January 1998. (Format: TXT=168759 bytes) (Obsoleted by RFC2274) (Status: PROPOSED STANDARD)
420
TCP/IP PRIMER PLUS
2265 View-based Access Control Model (VACM) for the Simple Network Management Protocol(SNMP). B. Wijnen, R. Presuhn, and K. McCloghrie. January 1998. (Format: TXT=77807 bytes) (Obsoleted by RFC2275) (Status: PROPOSED STANDARD) 2271 An Architecture for Describing SNMP Management Frameworks. D. Harrington, R. Preesuhn, and B. Wijnen. January 1998. (Format: TXT=128227 bytes) (Obsoletes RFC2261) (Status: PROPOSED STANDARD) 2272 Message Processing and Dispatching for the Simple Network Management Protocol (SNMP). J. Case, D. Harrington, R. Preesuhn, B. Wijnen. January 1998. (Format: TXT=88445 bytes) (Obsoletes RFC2262) (Status: PROPOSED STANDARD) 2273 SNMPv3 Applications. D.Levi, P. Meyer, and B. Stewart. January 1998. (Format: TXT=143754 bytes) (Obsoletes RFC2263) (Status: PROPOSED STANDARD) 2274 User-based Security Model (USM) for Version 3 of the Simple Network Management Protocol (SNMPv3). U. Blumenthal and B. Wijnen. January 1998. (Format: TXT=168950 bytes) (Obsoletes RFC2265) (Status: PROPOSED STANDARD) 2275 View-based Access Control Model (VACM) for the Simple Network Management Protocol(SNMP). B. Wijnen, R. Presuhn, and K. McCloghrie. January 1998. (Format: TXT=77998 bytes) (Obsoletes RFC2265) (Status: PROPOSED STANDARD) 2438 Advancement of MIB Specifications on the IETF Standards Track. M. ODell, H. Alvestrand, B. Wijens, and S. Bradner. October 1998. (Format: TXT=13633 bytes) (Also BCP0027) (Status: BEST CURRENT PRACTICE) 2493 Textual Conventions for MIB Modules Using Performance History Based on 15-minute Intervals. K. Tesink, Editor. January 1999. (Format: TXT=18749 bytes) (Status: PROPOSED STANDARD) 2570 Introduction to Version 3 of the Internet-standard Network Management Framework. J. Case, R. Mundy, D. Partain, and B. Stewart. April 1999. (Format: TXT=50381 bytes) (Status: INFORMATIONAL) 2571 An Architecture for Describing SNMP Management Frameworks. B. Wijnen, D. Harrington, and R. Presuhn. April 1999. (Format: TXT=139260 bytes) (Obsoletes RFC2271) (Status: PROPOSED STANDARD) 2572 Message Processing and Dispatching for the Simple Network Management Protocol (SNMP). J. Case, D. Harrington, R. Presuhn, and B. Wijnen. April 1999. (Format: TXT=96035 bytes) (Obsoletes RFC2272) (Status: DRAFT STANDARD) 2573 SNMP Applications. D. Levi, P. Meyer, B. Stewart. April 1999. (Format: TXT=150427 bytes) (Obsoletes RFC2273) (Status: DRAFT STANDARD) 2574 User-based Security Model (USM) for Version 3 of the Simple Network Management Protocol (SNMPv3). U. Blumenthal, B. Wijnen. April 1999. (Format: TXT=190755 bytes) (Obsoletes RFC2274) (Status: DRAFT STANDARD)
421
2575 View-based Access Control Model (VACM) for the Simple Network Management Protocol(SNMP). B. Wijnen, R. Presuhn, and K. McCloghrie. April 1999. (Format: TXT=79642 bytes) (Obsoletes RFC22275) (Status: DRAFT STANDARD) 2578 Structure of Management Information Version 2 (SMIv2). K. McCloghrie, D. Perkins, J. Schoenwaelder. April 1999. (Format: TXT=89712 bytes) (Obsoletes RFC1902) (Also STD0058) (Status: STANDARD) 2579 Textual Conventions for SMIv2. K. McCloghrie, D. Perkins, J. Schoenwaelder. April 1999. (Format: TXT=59039 bytes) (Obsoletes RFC1903) (Also STD0058) (Status: STANDARD) 2580 Conformance Statements for SMIv2. K. McCloghrie, D. Perkins, J. Schoenwaelder. April 1999. (Format: TXT=54253 bytes) (Obsoletes RFC1904) (Also STD0058) (Status: STANDARD) 2593 Script MIB Extensibility Protocol Version 1.0
Chapter 18: Open Network Computing Protocols

1014 XDR: External Data Representation standard. Inc. Sun Microsystems. Jun-01-1987. (Format: TXT=39316 bytes) (Status: UNKNOWN) 1094 NFS: Network File System Protocol specification. Inc. Sun Microsystems. Mar-01-1989. (Format: TXT=51454 bytes) (Also RFC1813) (Status: INFORMATIONAL) 1813 NFS Version 3 Protocol Specification. B. Callaghan, B. Pawlowski & P. Staubach. June 1995. (Format: TXT=229793 bytes) (Also RFC1094) (Status: INFORMATIONAL) 2054 WebNFS Client Specification. B. Callaghan. October 1996. (Format: TXT=4128 bytes) (Status: INFORMATIONAL) 2055 WebNFS Server Specification. B. Callaghan. October 1996. (Format: TXT=20498 bytes) (Status: INFORMATIONAL) 2623 NFS Version 2 and Version 3 Security Issues and the NFS Protocols Use of RPCSEC_GSS and Kerberos V5 2624 NFS Version 4 Design Considerations
APPENDIX B
ABBREVIATIONS AND ACRONYMS
A
ABR ACK ANSI API ARP ARPANET AS ASBR ASCII ASN.1 ATM area border router acknowledgement American National Standards Institute application program interface Address Resolution Protocol Advance Research Projects Agency network autonomous system autonomous system border router American Standard Code for Information Interchange Abstract Syntax Notation One Asynchronous Transfer Mode
B
BDR BER BGP BIND BootP BPF BRI BSD backup designated router Basic Encoding Rules Border Gateway Protocol Berkeley Internet Name Domain Bootstrap Protocol Berkeley Packet Filter Basic Rate Interface Berkeley Software Distribution
424
TCP/IP PRIMER PLUS
C
CCITT CIDR CIX CLNP CPU CSMA/CD CRC CSLIP CSMA CSU CUT Consultative Committee for International Telegraphy and Telephony classless interdomain routing Commercial Internet Exchange Connectionless Network Protocol central processing unit carrier sense multiple access collision detection cyclic redundancy check compressed SLIP carrier sense multiple access channel service unit Coordinated Universal Time
D
DARPA DCE DDN DDR DECNet DEMUX DF DHCP DLC DLPI DNS DoD DR Defense Advanced Research Projects Agency Distributed Computing Environment Defense Data Network Dial-on-Demand Routing Digital Equipment Corporation Network Demultiplexer dont fragment field (IP header) Dynamic Host Configuration Protocol Data Link control Data Link Provider Interface Domain Name System Department of Defense (Reference Model) designated router
Appendix B ABBREVIATIONS AND ACRONYMS
425
DSAP DSU DTP DTS DUAL DVMRP
Destination Service Access Point data service unit data transfer process Distributed Time Service Diffusing Update Algorithm Distance-vector Multicast Routing Protocol
E
EBGP EBONE EOL EGP EIGRP EMI external BGP (router) European IP Backbone end of option list Exterior Gateway Protocol Enhanced Interior Gateway Routing Protocol electromagnetic interference
F
FCS FDDI FIFO FIN FQDN FTP frame check sequence Fiber Distributed Data Interface first in, first out finish flag, TCP header fully qualified domain name File Transfer Protocol
GH
HA HDLC hardware address high-level data link control
426
TCP/IP PRIMER PLUS
I
IAB IAC IANA IBGP ICMP IDRP IEEE IESG IETF IGMP IGP IGRP IP IPNG IPX IRTF ISDN IS-IS ISN ISO ISOC Internet Architecture Board interpret as command Internet Assigned Number Authority internal BGP (router) Internet Control Message Protocol Interdomain Routing Protocol Institute of Electrical and Electronics Engineers Internet Engineering Steering Group Internet Engineering Task Force Internet Group Management Protocol Interior Gateway Protocol Interior Gateway Routing Protocol Internet Protocol Internet Protocol Next Generation Internetwork Packet Exchange Internet Research Task Force Integrated Services Digital Network Intermediate System to Intermediate System Protocol initial sequence number International Organization for Standardization Internet Society
JL
LAN LAPB LAPD LBX LCP Local Area Network Link Access Procedure, Balanced Link Access Procedure, D channel low bandwidth X link control protocol
427
LFN LIFO LLC LSA LSRR
long fat network last in, first out logical link control Link-state advertisement loose source and record route
M
MAC MBONE MIB MILNET MIME MS M/S MSL MSAU MSS MTA MTU MUX media access control multicast backbone management information base Military Network multipurpose Internet mail extensions message store master/slave maximum segment lifetime Multi-station Access Units maximum segment size maximum transfer agent maximum transfer unit Multiplexer
N
NAT NBMA NCP NDN NetBIOS NFS NIC Network Address Translation non-broadcast multi-access Network Control Protocol non-delivery notification Network Basic Input Output System Network File System network interface card
428
TCP/IP PRIMER PLUS
NIT NNTP NOAO NOP NSFNET NSI NSSA NTP NVT
network interface tap Network News Transfer Protocol National Optical Astronomy Observatories no operation National Science Foundation network NASA Science Internet not so stubby area Network Time Protocol network virtual terminal
O
Opcode OSF OSI OSPF Operation code Open Software Foundation Open Systems Interconnection (Reference Model) Open Shortest Path First
P
PA PDU PI POSIX PPP PRI PSH protocol address protocol data unit protocol interpreter Portable Operating System Interface Point-to-Point Protocol Primary Rate Interface push flag (TCP header)
Q
QoS Quality of Service
429
R
RARP RFC RFI RIP RPC RR RRQ RST RTO RTT Reverse Address Resolution Protocol Request for Comment radio frequency interference Routing Information Protocol remote procedure call resource record read request reset flag, TCP header retransmission timeout round-trip time
S
SA SACK SAP SDLC SLIP SMI SMTP SNA SNAP SNMP SQE SRRT SSAP SWS SYN source address Selective Acknowledgement service access point Synchronous Data Link Control Serial Line Internet Protocol structure of management information Simple Mail Transfer Protocol System Network Architecture Subnetwork Access Protocol Simple Network Management Protocol Signal Quality Error smooth round trip timer source service access point silly window syndrome synchronize sequence numbers flag, TCP header
430
TCP/IP PRIMER PLUS
T
TCP TFTP TLI ToS TTL TUBA Telnet Transmission Control Protocol Trivial File Transfer Protocol Transport Layer Interface type-of-service time-to-live TCP and UDP with bigger addresses Telecommunication Network Protocol
U
UA UDP UI URG UUCP user agent User Data Protocol user interface urgent pointer flag (TCP header) Unix-to-Unix Copy
V
VC VLAN VLSM virtual circuit Virtual Local Area Network Variable Length Subnet Mask
W
WAN WRQ WWW Wide Area Network write request World Wide Web
XZ
XDR XID XTI external data representation exchange ID or transaction ID X/Open Transport Layer Interface
APPENDIX C
TCP/UDP PORT NUMBERS
TABLE C.1 Decimal 20 21 23 25 37 49 53 63 67 68 69 69 70 80 137 139 161 161 179
able C.1 shows a list of TCP/UDP port numbers.
TCP/UDP Port Numbers

Keyword FTP-DATA FTP TELNET SMTP NTP LOGIN DNS VIA-FTP BOOTPS BOOTPC TFTP TFTP Gopher WWW NetBIOS-NS NetBIOS-DG SNMP SNMP BGP Protocol TCP TCP TCP TCP TCP TCP TCP/UDP TCP UDP UDP UDP TCP TCP TCP TCP TCP UDP TCP TCP Description File Transfer (Default Data) File Transfer (Control) Telnet Simple Mail Transfer Protocol Time or Network Time Protocol Login Host Protocol Domain Name Service VIA-Systems-FTP Bootstrap Protocol Server Bootstrap Protocol Client Trivial File Transfer Trivial File Transfer Protocol Gopher File Service World Wide Web Services NetBIOS Name Service NetBIOS Datagram Service Simple Network Management Protocol Simple Network Management Protocol Border Gateway Protocol
APPENDIX D
GLOSSARY
Numeric
1BASE5 Implements the IEEE 802.3 standard using 1Mbps transmission on a baseband medium with a maximum segment length of 500 meters. 10BASE2 Implements the IEEE 802.3 (Ethernet) standard using 10Mbps transmission on a baseband medium with a maximum segment length of 185 meters. 10BASE5 Implements the IEEE 802.3 (Ethernet) standard using 10Mbps transmission on a baseband medium with a maximum segment length of 500 meters. 10BASE-T Implements the IEEE 802.3 (Ethernet) standard using 10Mbps transmission on a baseband medium. Using this standard you can attach AUI-compatible devices to 24-gauge, unshielded twisted pair cable, rather than the usual coaxial media. 100BASE-FX Implements the IEEE 802.3 (Ethernet) standard using 100Mbps transmission on a baseband medium with multi-mode fiber-optic cable. 100BASE-T Implements the IEEE 802.3 (Ethernet) standard using 100Mbps transmission on a baseband medium with UTP wiring. 100BASE-T4 Implements the IEEE 802.3 (Ethernet) standard using 100Mbps transmission on a baseband medium with four pairs of Category 3, 4, or 5 UTP wiring. 100BASE-TX Implements the IEEE 802.3 (Ethernet) standard using 100Mbps transmission on a baseband medium. This standard enables the attachment of AUI-compatible devices to 24-gauge, unshielded twisted-pair cable, rather than the usual coaxial media. 100BASE-X Fast Ethernet specification using 100Mbps transmission, which refers to the 100BASEFX and 100BASETX standards for Fast Ethernet over fiber-optic cabling. 100VG-AnyLAN 100Mbps Fast Ethernet and Token-Ring media technology that uses four pairs of Category 3, 4, or 5 UTP cabling.
434
TCP/IP PRIMER PLUS
A
ABR (area border router) A router located on the border of one or more OSPF areas that connects those areas to the backbone network. AC (access control) DLC byte on the IEEE 802.5 Token-Ring network that contains the token indicator and frame priority information. access list services. List kept by routers to control access to or from the router for a number of The means by which network devices access the network. Processor connecting asynchronous devices to a LAN or WAN through emulaNetwork packet that acknowledges the receipt of data.
access method access server tion software.
ACK (Acknowledge)
acknowledgement Notification sent from one network device to another acknowledging that a particular event has occurred. active monitor Computer on a Token-Ring acting as a controller for the ring. It regulates the token and other aspects of performance. address Data structure for identifying a unique entity.
address mapping Technique for different protocols to interoperate by translating addresses from one format to another. address resolution adjacency Method for resolving differences between computer addressing schemes.
The process of forming a neighbor relationship.
ADSP (AppleTalk Data-Stream Protocol) Protocol that establishes and maintains fullduplex communication between two AppleTalk sockets. advertising The process by which a service makes its presence known on a network. Also used by routers to propagate route information. agent Software that processes queries and returns replies. A defined rule or process for arriving at a solution to a problem.
algorithm
all-routes explorer packet Explorer packet that travels the entire SRB network, following all possible paths to a destination. AMI (alternative mark inversion) (T1 lines) A pulse transmission T1 line coding scheme using alternate polarities in the pulse train. ANSI (American National Standards Institute) An industry-supported organization that helps to develop trade and communications standards. API (applications program interface) The programming interface that corresponds to the boundary between protocol layers. It specifies the functions and data used by one program module to access another.
Appendix D GLOSSARY
435
AppleTalk
A series of communications protocols designed by Apple Computer, Inc.
application layer Layer 7 of the OSI Reference Model, which provides services to application processes outside the OSI model. These can include e-mail, file transfer, and terminal emulation. architecture Refers to how a system is designed, and how its components connect and operate with each other. ARCnet Baseband token-passing network from the Datapoint Corporation. It can communicate among up to 255 stations at 2.5Mbps. area A set of network segments and their attached devices.
ARP (address resolution protocol) Used within TCP/IP to find a nodes DLC address from its IP address. Interpreted in the TCP/IP suite. It can also be interpreted in the Banyan VINES PI suite. ARPANET (Advanced Research Projects Agency Network) established in 1969. A packet-switching network
AS (autonomous system) A collection of networks under a common administration. They share a common routing strategy. ASBR (autonomous system boundary router) autonomous system and a non-OSPF network. An ABR located between an OSPF
ASCII (American Standard Code for Information Interchange) Provides mapping between numeric codes and graphical characters. Used universally for PC and non-IBM mainframe applications. asynchronous transmission Method of data transmission enabling characters to be sent at irregular intervals. This is done by preceding each character with a start bit and following it with a stop bit. One common application is to communicate with modems and printers. AUI (attachment unit interface) ceiver. A drop cable for Ethernet between the station and transA feature of a terminal adapter; it down-
AutoSPID (automatic service profile identifier) loads SPID information from a compatible switch. availability
The amount of time a network is operational.
B
B channel (Bearer channel) A 64kbps channel that is end-user data. backbone The backbone is the part of the communications network that carries the heaviest traffic. It is the basis for the design of the whole network service. background task A secondary job that is performed while the user performs a primary task, such as a network server carrying out the duties of the network (controlling communications) while the users are running applications (such as word processors) in the foreground.
436
TCP/IP PRIMER PLUS
bandwidth link.
The amount of data that can be moved through a particular communications All devices that share the same bandwidth.
bandwidth domain
bandwidth reservation A process of assigning bandwidth to users and applications served by a given network. It gives priority to different traffic flows based on how critical and delay sensitive they are. baseband A transmission technique that sends data bits without using a higher carrier frequency. The entire bandwidth of the transmission medium is used by one signal. baud rate A measure of the signaling speed in data communications. It specifies the number of signal elements that can be transmitted each second. For most purposes, at slow speeds, a baud rate is the same as the speed in bits per second. BDR (backup designated router) beacon In OSPF a backup to the DR. ,
A Token-Ring packet that signals a serious failure on the ring.
BECN (Backward Explicit Congestion Notification) Frame Relay. The sixth bit in the second octet of the Frame Relay header. It is used to inform a subscriber device of congestion in the backward direction. BGP (Border Gateway protocol) BGP, as defined in RFC 1771, enables the user to create loop-free, interdomain routing between autonomous systems. binary A numbering system using 1s and 0s (1=on; 0=off).
BIOS (basic input/output system) A set of routines that work with the hardware to support the transfer of information between elements of the system. These include memory, disks, and the monitor. bit A binary digit used in the binary numbering system. It can be 0 or 1. The speed at which bits are transmitted, commonly expressed in bits per second
bit rate (bps).
BNC (Bayonet Network Connector) A standardized coaxial cable connector; used for ARCNET networks and Thin Ethernet (Cheapernet) cables. BOOTP (Boot protocol) A protocol within TCP/IP used for downloading initial programs into networked stations. Interpreted in the TCP/IP PI suite. BPDU (Bridge protocol data unit) A spanning-tree protocol packet sent out at configurable intervals to exchange information with bridges in the network. bps (bits per second) A measure of the rate of data transmission.
breakout box A test device used to view the signals in an RS-232, a V.35, or other interface. The breakout box is used to diagnose problems with the interface. bridge A device used to connect two separate networks into one extended network. Bridges forward only packets that are meant for the other network.
Appendix D GLOSSARY
437
broadband A transmission technique that sends data bits encoded within a much higher radio-frequency carrier signal. The transmission medium can be shared by many simultaneous signals because each of them uses only a portion of the available bandwidth. broadcast (1) A message directed to all stations on a network or collection of networks. (2) A destination address that designates all stations. buffer A software program, storage space in RAM, or a separate device used to store data. For example, the Sniffer Network Analyzers capture buffer serves as a temporary storage space for captured network data until it can be analyzed or saved to disk. bursty traffic sion. Data communications term that refers to an uneven pattern of data transmis-
bus A common physical signal path composed of wires or other media, across which signals can be sent from one part of a computer to another (also known as a highway). bus topology A linear LAN architecture in which transmissions from network stations propagate the link of the medium and are received by all other stations. byte A series of consecutive binary digits operated on as a unit.
C
CA (Certificate Authority) cates. A third party that validates identities and creates digital certificaching A form of replication in which information learned during the previous transaction is used to process later transactions. capture The process by which the Sniffer analysis application records network traffic for interpretation. Generally speaking, this interpretation takes place during the display. However, the Expert Sniffer analysis application can simultaneously capture and interpret network traffic. category cabling standard. Consists of five grades of UTP cabling described in the EIA/TIA-586
CCITT (Consultative Committee for International Telegraphy and Telephony) The former name of International Telecommunications Union (ITU) that is a specialized body within the United Nations. It sponsors a number of standards dealing with data communications networks, telephone switching standards, terminals, and digital systems. channel A communications path. Refers to the attachment of devices directly by data channels to a comAccess link operating at 2.048Mbps.
channel attached puter. channelized E1
438
TCP/IP PRIMER PLUS
channelized T1
Access link operating at 1.544Mbps.
CHAP (challenge handshake authentication protocol) Security feature supported on lines with PPP encapsulation that helps prevent unauthorized access. chat script A group of three chat strings (setup, listen, and disconnect) that controls communication parameters for an asynchronous device. chat string A UNIX-style command/response sequence of characters downloaded to a serial device to control the device. CIDR (classless interdomain routing) Multiple contiguous Class C addresses owned by ISPs and assigned to downstream customers are summarized into one or more advertised IP addresses. CIR (committed information rate) The largest number of bits per second that a frame relay network agrees to carry over a PVC. CIR is assigned at the time of subscription to the frame relay service. circuit A communications path between two or more points.
circuit switching A switching system in which a dedicated physical circuit path must exist between sender and receiver for the duration of the call. classful routing protocols prefix length. classless routing protocols updates. Routing protocols that do not transmit information about the Routing protocols that include prefix length with routing
CLI (command-line interface) An interface that enables the user to interact with the operating system by entering commands and optional arguments. client (1) A module that uses the services of another modulefor example, the Session layer is a client of the Transport layer. (2) A PC or workstation that accesses services or applications from another server PC or workstation. CODEC (coder-decoder) A device that often uses PCM in transforming analog signals into a digital bit stream and digital signals into analog. collision In Ethernet, the result of two nodes transmitting simultaneously. The frames from each device collide and are damaged when they meet on the physical media. collision domain agated. In Ethernet, the network area in which frames that have collided are prop-
community In SNMP, a logical group of managed devices and NMSs in the same administrative domain. community string A text string that acts as a password and is used to authenticate messages sent between a management station and a router containing an SNMP agent. compression The reduction of the bandwidth or bits necessary to encode information.
Appendix D GLOSSARY
439
concentrator A central point for connecting several individual stations to a network ring. Commonly found on FDDI networks. connection-oriented connectionless Data transfer that requires the establishment of a virtual circuit.
Data transfer that occurs without the existence of a virtual circuit.
convergence The speed and capability of a group of internetworking devices running a specific routing protocol to arrive at a consistent understanding of the topology of an internetwork after a change in that topology. core layer Layer in a hierarchical network that provides optimal transport between sites. The main processor in a device, such as a computer or
CPU (central processing unit) router.
CRC (cyclic redundancy check) A check-word, typically 2 or 4 bytes at the end of a frame, that is used to detect errors in the data portion of the frame. CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) Random access or contention-based control technique. The algorithm used in LocalTalk networks that controls transmission. CSMA/CD Carrier Sense Multiple Access with Collision Detection. Random access or contention-based control technique. The algorithm used by IEEE 802.3 and Ethernet networks that controls transmission. CSU (channel service unit) An interface to a common carriers transmission facilities that ensures digital signals placed on the line are shaped and timed correctly. Often it is combined with a Data Service Unit (DSU). custom queuing A method of queuing used to guarantee bandwidth for traffic by assigning queue space based on port number, protocol, or other criteria. cut-through packet switching A packet switching approach that streams data through a switch so that the leading edge of the packet exits the switch at the output port before the packet finishes entering the input port.
D
D Channel Data channel used for signaling between the switching equipment and the customers equipment. This channel is not used for carrying user data. DAC (dual attachment concentrator) A concentrator offering two connections to the FDDI network, capable of accommodating the FDDI dual ring and other ports for the connection of other concentrators or FDDI stations. DAS (dual attachment station) counter-rotating ring. An FDDI station offering two connections to the FDDI dual
datagram A logical grouping of information sensed as a Network layer unit over a transmission medium without prior establishment of a virtual circuit.
440
TCP/IP PRIMER PLUS
Data Link layer Layer 2 of the OSI Reference Model, which provides reliable transit of data across a physical link. DB-9 A 9-pin standardized connector used in personal computers for a Token-Ring network connection (female), serial I/O port (male), and RGBI output (also used for LocalTalk). DB-15 A 15-pin standardized connector used at the transceiver, the drop cable, and the station of IEEE 802.3 or Ethernet network components. DB-25 A 25-pin standardized connector used in personal computers for parallel output ports (female connector on IBM PC chassis) or for serial I/O ports (male connector on 1BM PC chassis). DCE (data circuit-terminating equipment) Also called data communications equipment. On a serial communications link, it is the device that connects the DTEs into the communication line or channel. DDP (Datagram delivery protocol) Adds to the services of the underlying link access protocol by including an internetwork of interconnected AppleTalk networks, with a provision to address packets to sockets within a node. Interpreted in the AppleTalk PT suite. DDR (dial-on-demand-routing) A technique in which a Cisco router can automatically initiate and close a circuit-switched session as transmitting stations demand. DE (discard eligibility) The seventh bit of the second octet of the frame relay header. A value of 1 in the DE bit indicates that the frame is eligible for discard by a congested network. decapsulation decryption The unwrapping of data from a particular protocol header.
The restoring of data to its original, unencrypted state. Network segment allocated to a single device. A line reserved for transmissions, rather than being switched as transmission
dedicated LAN dedicated line is required.
default route A routing table entry used to direct packets for which the next hop is not explicitly listed in the routing table. default router The router to which packets are directed when a next hop is not explicitly listed in the routing table. delay The time between the beginning of the transaction by a sender and the first response received by the sender. delay-sensitive traffic ingly. destination address Traffic requiring timeliness of delivery and that varies its rate accordThe part of a message indicating for whom the message is intended.
DHCP (Dynamic Host Configuration Protocol) Enables IP addresses to be allocated dynamically so addresses can be reused after hosts no longer need them.
Appendix D GLOSSARY
441
dial-up line A communications circuit established by a switched-circuit connection using the telephone network. DIP switch (dual inline package switch) A switch attached to a printed circuit board; usually a small screwdriver is required to change it. There are two settingson and off. Printed circuit boards usually have banks of multiple DIP switches that are used to configure the board in a semi-permanent way. DISC Disconnect. An LLC non-data frame indicating that the connection established by an earlier SABM or SABME is to be broken. display The process in which the Sniffer analyzer interprets the traffic recorded during capture. During display, the analyzer decodes the layers of protocol in the recorded frames and displays them as English abbreviations or summaries. distance vector routing algorithm Class of routing algorithms calling for each router to send some or all of its routing table to its neighbors. Distribution layer tivity. The layer in a hierarchical network that provides policy-based connec-
DLC (Data Link Control) The lowest protocol layer within the transmitted network frame. Its fields typically include the source address, the destination address, and sometimes additional control information. DLCI (Data Link connection identifier) that identifies a virtual circuit. 10-bit number used by the frame relay protocol
DM (Disconnected Mode) An LLC message acknowledging that a previously established connection has been broken. DNS (domain name service) A protocol within TCP/IP used for discovering information about resources using a database distributed among different name servers. Interpreted in the TCP/IP suite. DR (designated router) An OSPF router generating LSAs for a multi-access network. T1 lines. A single 64Kbps channel in a DS1 signal. See also
DS0 (digital signal level 0) DS1 and DS3.
DS1 (digital signal level 1) T1 lines. Basic digital signal for transmission over T1 facilities. The DS1 signal consists of 24 channels at 64Kbps (called DS0, or Digital signal level 0, channels), plus 8Kbps used for synchronization and signalingfor a total bandwidth of 1,544Kbps. DS3 (digital signal level 3) 44.736Mbps. T3 lines. Specification for transmitting digital signals at
DSAP (destination service access point) The LLC SAP for the protocol expected to be used by the destination station for decoding the frame data.
442
TCP/IP PRIMER PLUS
DSL (Digital Subscriber Line) Technology used between the customer premise and service provider using high-frequency ranges to enable higher bandwidth capacity over standard copper wires. DSU (data service unit) A device that connects terminal equipment to digital communications lines. See also CSU. DTE (data terminal equipment) A generic term used to describe the host or end user machine on a serial communications link. DUAL (diffusing update algorithm) A convergence algorithm used in enhanced IGRP, which provides loop-free operation throughout a route computation. duplex A characteristic of data transmission, either full- or half-duplex. Full-duplex permits simultaneous two-way communication. Half-duplex means only one side can talk at a time. DVMRP (Distance Vector Multicast Routing Protocol) datagrams through an internetwork. dynamic routing A protocol for routing multicast
Routing that automatically adjusts the network topology or traffic changes.
E
E1 A digital transmission link with a capacity of 2.048Mbps (CCITT version of T1). EBCDIC (Extended Binary Coded Decimal Interchange Code) Mapping between numeric codes and graphical characters used for IBM mainframe computers and communications protocols defined by IBM. Echo (1) A request/response protocol within XNS used to verify the existence of a host. (2) A protocol within AppleTalk that enables any node to send a datagram to any other node and to receive an echoed copy of that packet in return to verify the existence of that node or to make round-trip delay measurements. Interpreted in the AppleTalk PI suite. (3) A protocol transmitted by a Net RPC frame in Banyan VINES. EGP (Exterior Gateway Protocol) A protocol within TCP/IP used in exchanging routing information among gateways belonging to either the same or different systems. EIA (Electronic Industries Association) A standard organization specializing in the electrical and functional characteristics of interface equipment. EIGRP (Extended Interior Gateway Routing Protocol) An enhanced version of IGRP and a suite of Cisco routing protocols used in TCP/IP and OSI internetworks. ELAP See LAP . The wrapping of data in a particular protocol header.
encapsulation
encryption Applying a specific algorithm to data to alter its appearance and make it incomprehensible to those who are not authorized to see the information.
Appendix D GLOSSARY
443
Error A protocol within XNS by which a station reports receiving and discarding a defective packet. Interpreted in the XNS PI suite. error rate In data transmission, the ratio of the number of incorrect elements transmitted to the total number of elements transmitted. ESF (Extended Superframe Format) 193rd bit to signal line problems. T1. A modification of the DS1 format that uses the
Ethernet A CSMA/CD network standard originally developed by Xerox; similar to (and often used interchangeably with) the IFFE 802.3 standard. Ethertype A 2-byte protocol-type code in Ethernet frames used by several manufacturers but independent of the IEEE 802.3 standard. event A network message that indicates irregularities in operation of the physical elements of a network. expansion Running a compressed data set through an algorithm that restores the data set to its original size. explorer packet SRB network. The packet generated by an end station trying to find its way through an
exterior gateway protocol An internetwork protocol used to change routing information between autonomous systems.
F
Fast Ethernet Includes any number of 100Mbps Ethernet specifications, at a speed 10 times faster than the 10BaseT Ethernet specification. FC (frame control) FCS On a Token-Ring network, the DLC byte that contains the frames type.
See frame check sequence.
FDDI (Fiber distributed data interface) An ANSI/ISO standard that defines a 100Mbps LAN over a fiber-optic medium using a timed token over a dual ring of trees. FE (framing error) An error that occurs because of incorrect framing of data units transmitted. In asynchronous transmission, this is usually due to a deviation in the stop bit cell. FECN (forward explicit congestion notification) (Frame relay) The fifth bit in the second octet of the frame relay header. Used to inform a subscriber device of congestion in the forward direction. FEP (front-end processor) Sits in front of a computer and is designed to handle the telecommunications burden so the computer can concentrate on handling the processing burden. fiber-optic cable A cable that conducts modulated light transmission.
444
TCP/IP PRIMER PLUS
filter The Sniffer analysis application uses several varieties of filters, including capture filters that determine which arriving frames the analyzer discards and which it retains. The Sniffer also uses display filters that determine which frames in the capture buffer will be displayed. Eliminating a frame from a display with a display filter does not remove the frame from memory. firewall An access server or router designated as a buffer between any connections from public networks to a given private network. A firewall router ensures the security of the private network. flash update topology. A routing update sent asynchronously in response to a change in the network
floating static route A static route that has a higher administrative distance than a dynamically learned route, so that it can be overridden by dynamically learned routing information. flooding A technique used by bridges and switches in which traffic received on an interface is sent out from all the interfaces of the device, except the interface from which the information was originally received. flow control Hardware or software mechanisms used in data communications to turn off transmission when the receiving workstation is incapable of storing the data it is receiving. Refers to various methods of regulating the flow of data during a conversation. Buffers are an example of flow control. fragmentation The process of breaking a packet into smaller units when transmitting over a network that cant support a packet of the original size. frame The multi-byte unit of data transmitted at one time by a station on the network. It is synonymous with the term packet. frame check sequence (FCS) In bit-oriented protocols, a 16-bit field added to the end of a frame that contains transmission error-checking information. Frame Relay A streamlined access protocol commonly used for LAN interconnectivity.
FRMR (frame reject) An LLC command or response indicating that a previous frame had a bad format and is being rejected. The FRMR frame contains five bytes of data that explain why the previous frame was bad. Front-end processor See FEP .
FS (frame status) A byte appended to a Token-Ring network frame following the CRC. It contains the Address Recognized and Frame Copied bits. FTP (file transfer protocol) (1) A protocol based on TCP/IP for reliable file transfer. Interpreted in the TCP/IP PI suite. (2) A protocol transmitted by a Net RPC frame in Banyan VINES. full-duplex The capability to have simultaneous data transmission between a sending and receiving station.
Appendix D GLOSSARY
445
full mesh A network in which devices have been organized in a mesh topology, with each network node having a virtual or physical circuit connecting to every other network node. functional address A limited broadcast destination address for IEEE 802.5 Token-Ring networks. Individual bits in the address specify attributes that stations eligible to receive the frame should have. Similar to multicast address.
G
gateway A computer that connects two different networks. Usually, this means two different kinds of networks. However, in TCP/IP terminology a gateway connects two separately administered subnetworks, which might or might not be running the same networking protocols. GNS (Get Nearest Server) Request packet sent by a client on an IPX network to locate the nearest active server of a particular type. GUI (graphical user interface) Pronounced goo-ey. An operating system or environment that displays options onscreen as icons or picture symbols.
H
handshaking The electrical exchange of predetermined signals when a connection is made between two devices carrying data. Computers must handshake through a procedure of greeting the opposite device. HDLC (high-level data link control) A standard bit-oriented protocol developed by the International Standards Organization (ISO). In HDLC, control information is always placed in the same position. Specific bit patterns used for control differ dramatically from those used to represent data, minimizing errors. Many internetworking companies (such as Cisco and Vitalink) have developed proprietary versions of HDLC that the Sniffer Internetwork analysis application can decode. header The beginning portion of a message that contains the destination address, source address, message-numbering, and other information. The header helps direct the message along its journey. Different protocols implement headers in different ways. heartbeat On Ethernet, the SQE signal generated by the transceiver at the end of a transmitted frame to check the SQE circuitry. See SQE TEST. hop A term used in routing. A hop is one data link. A path to the final destination on a net is a series of hops away from the origin. Each hop has a cost associated with it, enabling the calculation of a least-cost path. hop count tion. host A routing metric used to measure the distance between a source and its destina-
A computer system on a network.
446
TCP/IP PRIMER PLUS
host number The part of an IP address that designates which node on the subnetwork is being addressed. hub A concentrator and repeater for the network. Generally speaking, a hub is a central point for wiring or computing in a network.
I
IARP (Inverse Address Resolution Protocol) IARP enables a frame relay station to discover the protocol address corresponding to a given hardware address. ICMP (Internet Control Message Protocol) A protocol within TCP/IP mainly used to report errors in datagram transmission. Interpreted in the TCP/IP suite. ID Identification.
IEEE (Institute of Electrical and Electronics Engineers, Inc.) A standards body that focuses primarily on the Physical and Data Link layers and extends to LAN management. Standards documents are available from them at 345 East 47th Street, New York, NY 10017. IETF (Internet Engineering Taskforce) developing Internet standards. A taskforce of more than 80 groups responsible for
I-Frame (information frame) An LLC, HDLC, or SDLC frame type used to send sequenced data that must be acknowledged. IGMP (Internet Group Management Protocol) Used to keep neighboring multicast routers informed of the host group memberships present on a particular local network. IGP (Interior Gateway Protocol) within an autonomous system. Internet protocol used to exchange routing information Cisco routing protocol designed for campus-
IGRP (Interior Gateway Routing Protocol) wide use, as opposed to wide-area use.
Interface (1) A connection between two devices or systems. (2) A network connection in routing terminology. (3) A shared boundary in telephony. (4) The boundary between adjacent layers of the OSI model. Internet internet The largest global internetwork, connecting thousands of networks worldwide. Short for internetwork, and not to be confused with Internet. A collection of one or more networks with different protocols and connecting
internetwork devices. Intranet
A network that is internal to an organization, based on Web technology.
I/O (Input/Output) The part of a computer system or the activity that is primarily dedicated to the passing of information into or out of the central processing unit or memory.
Appendix D GLOSSARY
447
IP (Internet Protocol) The lowest-layer protocol under TCP/IP that is responsible for endto-end forwarding and long packet fragmentation control. Interpreted in the TCP/IP PI suite. A similar protocol is interpreted in the Banyan VINES PI. See also IPX and ISO. IP address address. 32-bit address assigned to hosts using TCP/IP. Sometimes called an Internet
IP multicast Routing technique enabling IP traffic to be sent from one source to several destinations, or from many sources to many destinations. IPX Internet packet exchange. Novells implementation of Xerox Internet Datagram Protocol. Interpreted in the Novell NetWare PI suite. ISDN (Integrated Services Digital Network) voice and data services on a single circuit. A digital telephone technology that combines
ISL (inter-switch link) Cisco protocol maintaining VLAN information as traffic flows between switches and routers. ISO (International Standards Organization) (1) A consortium that is establishing a set of networking protocols. (2) The protocols standardized by that group. ISP (Internet service provider) Provides Internet access to a company or individual.
ITU-T (International Telecommunications Union Telecommunication Standardization Sector) International body that sets worldwide standards for telecommunications technologies.
JK
Kbps (Kilobits per second) keepalive interval A measure of the rate of data transmission. The time between each keepalive message sent by a network device. keepalive message Message sent by one network to another informing it that the circuit between the two is still alive.
L
LAN (local area network) ited geographical area. LANE (LAN emulation) The hardware and software used to connect computers in a limEnables an ATM network to function as a LAN backbone.
LAP (Link Access Protocol) The logical-layer protocol for AppleTalk. It exists in two variants: ELAP (for Ethernet) and LLAP (for LocalTalk networks). Interpreted in the AppleTalk PI. LAPB (Link Access Protocol Balanced) A subset of HDLC.
448
TCP/IP PRIMER PLUS
LAPD (Link Access Protocol-D) ISDN.
A link control protocol based on HDLC that is related to
LAT (Local Area Transport) The DECnet protocol that handles multiplexed terminal (keyboard and screen) traffic to and from timesharing hosts. Interpreted in the DECnet PI suite. latency (1) The delay between the time a device requests access to a network and the time it is allowed to transmit. (2) Also called insertion delay, the delay between the time a device receives a frame and the time the frame can be forwarded out the destination port. leased line A telephone line rented for exclusive, continuous use. Commonly used to connect remote LANs. The same as a leased circuit, dedicated circuit, or leased channel. link Network communications channel consisting of a transmission or circuit path and all the related equipment between a sender and a receiver. Often used in reference to a WAN connection. link protocol The set of rules by which a logical data link is set up and by which data transfers across the link. Includes formatting of the data. Link state routing protocol Also known as Shortest Path First Algorithm. Examples of Link state protocols are NLSP and OSPF Link state routing protocols maintain topology maps, offer . faster convergence, and send updates only when changes occur on the network. LLAP See LAP .
LLC (Logical Link Control) A protocol that provides connection control and multiplexing to subsequent embedded protocols; standardized as IEEE 802.2 and ISO/DIS 8802/2. LMI (Local Management Interface) An access signaling protocol defined for frame relay circuits. LMI carries information on the status of permanent virtual circuits between the network and a subscriber device. Additions to LMI can include multicasting, global addressing, and flow control. load balancing The capability of a router to distribute traffic over all its network ports. This helps increase effective network bandwidth. local explorer packet A packet generated by an end system in an SRB network to find a host connected to the local ring. LOOP (Loopback) A protocol under Ethernet for sending diagnostic probe messages. The lowest-order (usually rightmost) bit of a binary number.
LSB (least significant bit)
M
MAC (Medium Access Control) The protocol layer that describes network management frames sent on the 802.5 Token-Ring. Most MAC frames are handled transparently by the network adapter.
Appendix D GLOSSARY
449
MAC address Standardized Data Link layer address required of every device or port connected to a LAN. Also known as a MAC layer address, hardware address, or physical address. MAN (metropolitan-area network) managed device protocol. A network spanning a metropolitan area.
A network device that can be managed by a network management
Manchester encoding A data encoding technique that uses a transition at the middle of each bit period that serves as a clock and also as data. MAU (multiple access unit) (Also known as a medium attachment unit.) The wiring concentrator or transceiver used for attaching stations connected to the network. MB (megabyte) A measure of the rate of data transmission. A measure of the rate of data transmission.
MBps (megabytes per second)
mesh A network topology in which devices are organized in a segmented manner with many interconnections placed between network nodes. MIC (media interface connector) An optical fiber connector pair that links the fiber media to the FDDI node or another cable. mirroring Synchronizing two disks on a file server.
modem A contraction of modulate and demodulate. A conversion device installed in pairs at each end of an analog communications line. The modulator part of the modem codes digital information onto an analog signal by varying the frequency of the carrier signal. The demodulator part extracts digital information from a modulated carrier signal. MOP (Maintenance Operations Protocol) problem diagnosis. MSB (most significant bit) sign bit. A protocol under DECnet for remote testing and
The highest-order bit of a binary number, not including the The average time between failures of a device. The maximum packet size, in bytes, that a particular
MTBF (mean time between failure) MTU (maximum transmission unit) interface can handle.
MTU Discovery A function enabling software to discover and use the largest frame size that will travel over the network without requiring fragmentation. multicast (1) A message directed to a group of stations on a network or collection of networks (contrast with broadcast). (2) A destination address that designates such a subset. multiplexing end. Sending several signals over a single line and separating them at the other
450
TCP/IP PRIMER PLUS
N
NAK (negative acknowledgment) A response from the recipient of data to the sender of that data that indicates the transmission was unsuccessful (that is, the data was corrupted by transmission errors). NBMA (non-broadcast multi-access) A multi-access network that either does not support broadcasting or in which broadcasting is not feasible. NCP (NetWare Core Protocol) Novells Application layer protocol for the exchange of commands and data between file servers and workstations. Interpreted in the Novell NetWare PI suite. NDS (Network Directory Services) manage network resources. NDS is a Novell application that operates with NCP to A programming specification for
NetBEUI (NetBIOS Basic Extended User Interface) NetBIOS.
NetBIOS (Network Basic Input/Output System) (1) A protocol implemented by the PC LAN program to support symbolically named stations and the exchange of arbitrary data. (2) The programming interface (API) used to send and receive NetBIOS messages. Several different and incompatible implementations of NetBIOS exist, each with a separate API; for example, in the IBM and Novell suites. NetWare The networking system designed by Novell, Inc. and the protocols used therein.
network A collection of computers, printers, switches, routers, and other devices that are capable of communicating with each other over a transmission medium. network address A Network layer address referring to a logical network device; also known as a protocol address. network layer Layer 3 of the OSI Reference Model. It provides connectivity and path selection between two end systems. network management Systems that help maintain or troubleshoot a network.
network management protocol The protocol that management entities within NMSs use to communicate with agents in managed devices. network topology ring, bus, and star. The geography of a network. Examples of network topologies include
NFS (network file system) A protocol developed by Sun Microsystems for requests and responses to a networked file server. NLM (NetWare Loadable Module) An individual program that can be loaded into memory and function as part of the NetWare NOS. NLSP (NetWare Link Services Protocol) A Link state protocol that improves the performance, reliability, scalability, and manageability of IPX traffic in large-scale LAN-WAN internetworks.
Appendix D GLOSSARY
451
nodes Points on a network where service is provided or used, or where communications channels are interconnected. Node sometimes is used interchangeably with the term workstation. non-local traffic Traffic needing to travel to different network segments. A term used to refer to distributed filesystems.
NOS (network operating system)
N(R) (receive sequence number) An LLC or HDLC field for information frames indicating the sequence number of the next frame expected; all frames before N(R) are thus implicitly acknowledged. N(S) (send sequence number) An LLC or HDLC field for information frames that indicates the sequence number of the current frame within the connection. NT1 (Network Termination 1) In ISDN, a device providing the interface between customer premises equipment and central office switching equipment. NTP/SNTP (Network Time Protocol/Simple Network Time Protocol) vides the mechanisms to synchronize time distribution in the Internet. Null modem Cross-pinned cable used for DTE to DTE. RAM that retains its contents when a unit is powered off. NTP or SNTP pro-
NVRAM (non-volatile RAM)
O
octet String of eight bits; synonymous with byte. ODI (Open Data-Link Interface) A Novell specification providing a standardized interface for NICs (network interface cards), enabling multiple protocols to use a single NIC. OSI (open systems interconnection) interconnection of systems. OSPF (Open Shortest Path First) RIP on the Internet. A generalized model of layered architecture for the
A Link state IGP routing algorithm proposed to succeed
Overhead Information that provides support for computing processes but is not an intrinsic part of the data or operation.
P
packet Multi-byte unit of data transmitted one unit, or packet, at a time by a station on the network. Synonymous with the term datagram. packet switching Method for sending data in packets through a network to a remote location. Data is subdivided into individual packets, each with its own identification and carrying the destination address. Packets then can be sent by different routes and reassembled in sequence by the packet ID.
452
TCP/IP PRIMER PLUS
PAD (packet assembler disassembler) Computer on an X.25 network that enables asynchronous terminals to use the synchronous X.25 network by packaging asynchronous traffic into packets. parallel interface An interface that permits parallel transmission (or simultaneous transmission of the bits making up a character or byte) over separate channels or on different carrier frequencies of the same channel. parity bit A binary bit appended to an array of bits to make the sum of the bits always odd or always even. Used with a parity check for detecting errors in transmitted binary data. parity check A process for detecting whether bits of data have been altered during transmission of that data. partial mesh A network in which devices are organized in a mesh topology, with some network nodes organized in a full mesh, but with others that are connected to only one or two other nodes in the network. PAT (port address translation) Cisco feature that enables the translation of private addresses into registered IP addresses by using port numbers. patch panel A device in which temporary connections can be made between incoming and outgoing lines. Used for modifying or reconfiguring a communications system or for connecting test instruments (such as the Sniffer Network Analyzer) to specific lines. path control layer Layer 3 in the SNA architectural model. Performs sequencing services related to proper data reassembly. payload The portion of a frame that contains the upper-layer information (data). Common abbreviation for a personal computer.
PC (personal computer)
PDU (protocol data unit) The data delivered as a single unit between peer processes on different computers. An OSI term for information at any layer in the OSI model. PDV (path delay value) The total round-trip propagation delay in an Ethernet network.
Physical layer Layer 1 of the OSI Reference Model. Concerned with the mechanical and electrical aspects of maintaining links between end systems. pilot A pilot of a network is a scaled-down prototype used to demonstrate basic functions; used most often for smaller networks. Ping A TCP/IP tool supplied with TCP/IP Distributed Sniffer System. Ping is a diagnostic utility that sends ICMP Echo Request messages to a specific IP address on the network. policy routing A routing scheme that forwards packets to specific interfaces based on userconfigured policies. port The physical access point to a computer, multiplexer, device, or network where signals can be sent or received.
Appendix D GLOSSARY
453
PPP (Point-to-Point Protocol) RFC 1331. PPP is a link-level protocol that bypasses X.25 for communication between systems that are directly connected, running any of a variety of protocols directly over HDLC. pps (packets per second) networking devices. A measurement of throughput and performance of networks and
preamble A fixed data pattern transmitted before each frame to allow receiver synchronization and recognition of the start of a frame. Presentation layer The sixth layer of the OSI model (ISO 8823). It controls the formats of screens and files. Control codes, special graphics, and character sets work in this layer. PRI (primary rate interface) ISDN interface to primary rate access.
priority queuing A method of queuing used to guarantee bandwidth for traffic by assigning space based on protocol, port number, or other criteria. Priority queuing has four levels: low, normal, medium, and high. The high queue is emptied first. private addresses Reserved IP addresses to be used internally only. They include: 10.0.0.010.255.255.255, 172.16.0.0172.31.255.255, and 192.168.0.0192.168.255.255. process switching An operation that provides full write evaluation and per-packet load balancing across parallel WAN links. It involves the transmission of entire frames to the route for CPU, where they are repackaged for delivery to or from a WAN interface, with the router making a route selection for each packet. protocol A specific set of rules, procedures, or conventions governing the format and timing of data transmission between two devices. protocol stack A set of related communications protocols that operate together and address communication at the seven layers of the OSI Reference Model. prototype A prototype of a network involves implementing a portion of the network to prove that its design meets the requirements used for larger networks. provisioning proxy Defining the type of WAN, including the specifications and options.
An entity that stands in for another entity in the interest of efficiency.
proxy ARP (Proxy Address Resolution Protocol) A variation of the ARP protocol in which an intermediate device sends an ARP response on behalf of an end node to the requesting host. PUP (PARC Universal Packet) A type of Ethernet packet formerly used at the Xerox Corporations Palo Alto Research Center. Interpreted in the XNS/MS-Net and the TCP/IP PIs but not included in their protocol diagrams because its no longer in regular use. PVC (permanent virtual circuit) of a network. Used by frame relay. A unique, predefined logical path between two endpoints
454
TCP/IP PRIMER PLUS
Q
query A message inquiring about the value of a variable or set of variables. queue (1) A list of elements, in order, waiting to be processed. (2) In routing, a backlog of packets waiting to be forwarded. QoS (quality of service) its transmission quality. A measure of performance for a transmission system that reflects
R
RAM (random access memory) Memory that can be read and written by a microprocessor. RARP (Reverse Address Resolution Protocol) A protocol within TCP/IP used for finding a nodes IP address, given its DLC address. Interpreted in the TCP/IP PI suite. Rate-sensitive traffic reassembly mented. Traffic that is willing to give up timeliness for guaranteed rate.
Putting an IP datagram together again at its destination, after it has been frag-
redistribution Distributing routing information discovered through one routing protocol in the update messages of another routing protocol. redundancy Duplication of devices, connections, or services, so that in case of failure, these can perform the work of the ones that failed. REJ (Reject) An LLC frame type that requests retransmission of previously sent frames.
reliability The ratio of expected to received keepalives from a link. If this is a high ratio, the line is reliable. REM (ring error monitor) A station on the 802.5 Token-Ring network that collects MAC layer error messages from the other stations. repeater A device inserted at intervals along a circuit to boost, amplify, and regenerate the signal being transmitted. response time The amount of time to receive a response to a request for a service from the network system. RFC (Request For Comment) opment. RG-58 RG-59 RG-62 Designation used in DoD/TCP protocol research and devel-
The designation for 50-ohm coaxial cables used by Cheapernet (thin Ethernet). The designation for 75-ohm coaxial cables used by PC Network (broadband). The designation for 93-ohm coaxial cables used by ARCNET.
Appendix D GLOSSARY
455
RII (routing information indicator) If the first bit in the source address field of a TokenRing frame is 1, the data field begins with routing information. Interpreted by the Token-Ring or Ethernet Sniffer analysis application independent of other PIs. ring A connection of two or more stations in a logically circular topology. Information is passed sequentially between active stations. ring topology A network topology that consists of a series of repeaters connected to one another by unidirectional transmission links to form a single closed loop. Each station on the network connects to the network at a repeater. Ring topologies are most often organized in a closed-loop star. RIP (Routing Information Protocol) A protocol within the XNS and TCP/IP families used to exchange routing information among gateways. Interpreted in the XNS PT suite and TCP/IP PI suite. RISC (reduced instruction set computer) A type of microprocessor design that focuses on rapid and efficient processing of a relatively small set of instructions. RJ-45 The designation for the 8-wire modular connectors used in 10BASE-T networks. It is similar to, but wider than, the standard (RJ-11) telephone modular connectors. rlogin (remote login) tions. A terminal emulation program offered in most UNIX implementa-
RMON (Remote Monitoring) Management Information Base (MIB). Uses SNMP and standard MIB design to provide multi-vendor interoperability between monitoring products and management stations. RNR (Receive Not Ready) mission is blocked. ROM (read-only memory) route An LLC and HDLC command or response indicating that transMemory that can be read by the microprocessor but not written.
A path through an internetwork.
route summarization The consolidation of the advertised addresses in a routing table. This reduces the number of routes in the routing table, the routing update traffic, and the overall or router overhead. routed protocol A protocol that can be routed by a router. A routed protocol contains enough Network layer addressing information for user traffic to be directed from one network to another network. Routed protocols define the format and use of the fields within a packet. router An internet linking device operating at the Network layer (ISO layer 3).
routing The process of finding a path to a destination host. Routing can be complex in larger networks because of the many potential intermediate destinations that a packet might travel through before reaching its destination host. routing domain A group of end systems and intermediate systems operating under the same set of administrative rules.
456
TCP/IP PRIMER PLUS
routing metric A standard of measurement, such as a path length, that is used by routing algorithms to determine the optimal path to the destination. This information is stored in routing tables. Metrics include communication cost, bandwidth, hop count, delay, path cost, MTU, and reliability. routing protocol A routing protocol supports a routed protocol by providing mechanisms for sharing routing information. Routing protocol messages move between the routers. A routing protocol enables the routers to communicate with other routers to update and maintain routing tables. Routing protocol messages do not carry end-user traffic from network to network. A routing protocol uses the routed protocol to pass information between routers. routing table A table stored in a router or some other internetworking device that keeps track of routes to particular network destinations and metrics associated with those routes. routing update A message sent from a router to indicate network reachability and associated cost of information. Typically sent at regular intervals after a change occurs in the network topology. RPC (Remote Procedure Call) A protocol for activating functions on a remote station and retrieving the results. Interpreted in the Sun PI suite. A similar protocol exists in Xerox XNS. RPL (Remote Program Load) A protocol used by IBM on the IEEE 802.5 Token-Ring network to download initial programs into networked stations. Interpreted in the IBM PI suite. RPS (ring parameter server) A station on a Token-Ring network that maintains MAC layer information about the LAN configuration, such as ring numbers and physical location identifiers. RR (receive ready) other station. An LLC non-data frame indicating readiness to receive data from the
RS232 or RS232C (Recommended Standard 232) EIA standard defining electrical characteristics of the signals in the cables that connect a DTE and a DCE. RTMP (Routing Table Maintenance Protocol) Used in AppleTalk networks to enable internetwork routers to dynamically discover routes to the various networks of an internet. A node that is not a router uses a subset of RTMP (the RTMP stub) to determine the number of the network to which it is connected and the node IDs of routers on its network. Interpreted in the AppleTalk protocol interpreter.
S
S or S Frame (Supervisory Frame) functions. An LLC, HDLC, or SDLC frame type used for control SABM (set asynchronous balanced mode) An LLC non-data frame requesting the establishment of a connection over which numbered information frames can be sent.
Appendix D GLOSSARY
457
SABME (set asynchronous balanced mode [extended]) control field. Used in LAPB.
SABM with two more bytes in the
SAC Single attachment concentrator. A concentrator that offers one S port for attachment to the FDDI network and M ports for the attachment of stations or other concentrators. SAP (service access point) (1) A small number used by convention, or established by a standards group, that defines the format of subsequent LLC data; a means of demultiplexing alternative protocols supported by LLC. (2) (Service Advertising Protocol) Used by NetWare servers to broadcast the names and locations of servers and to send a specific response to any station that queries it. SDLC (Synchronous Data Link Control) An older serial communications protocol that was the model for LLC and with which it shares many features. security management One of five categories of network management defined by ISO for management of the OSI networks. Subsystems within these control access to various network services. segment (1) A section of any network that is bounded by routers, bridges, or switches. (2) In a LAN using a bus topology, a continuous electrical circuit often connected to other segments with repeaters. (3) In the TCP specification, a single Transport layer unit of information. serial interface An interface that requires serial transmission, or the transfer of information in which the bits composing a character are sent sequentially. Implies only a single transmission channel. server Session suite. A node or software program that provides services to clients. Name for the Session layer protocol in the ISO series, interpreted in the ISO PI
Session layer Layer 5 of the OSI Reference Model. This layer establishes, manages, and terminates sessions between applications, and manages data exchange between Presentation layer entities. shielded cable interference. A cable that has a layer of shielded insulation to reduce electromagnetic
silicon switching A type of switching in which an incoming packet matches an entry in the silicon switching cache located in the SSE of the SSP module. simplex The capability for data transmission in only one direction between a sending station and a receiving station. single-route packet destination. A packet in an SRB network that follows only one specific path to its
sliding window flow control A method of flow control in which a receiver gives a transmitter permission to transmit data until a window is full. When the window is full, the transmitter must stop transmitting until the receiver advertises a larger window.
458
TCP/IP PRIMER PLUS
SLIP (Serial Line Internet Protocol) tions using a variation of TCP/IP.
Standard protocol for point-to-point serial connec-
SMB (server message block) A message type used by the IBM PC LAN program to make requests from a user station to a server and receive replies. Many of the functions are similar to those made by an application program to DOS or to OS/2 running on a single computer. SMDS (switched multi-megabit data service) networking technology. A packet-switched, datagram-based WAN
SMT (station management) Provides ring management, connection management, and frame services for an FDDI ring. SMTP (Simple Mail Transfer Protocol) A protocol within TCP/IP for reliable exchange of electronic mail messages. Interpreted in the TCP/IP PI suite. SNA (1) (Systems Network Architecture) A set of protocols used by IBM for network communications, particularly with mainframe computers. Interpreted in the IBM PI suite. (2) (Sniffer Network Analyzer). Network Generals network analyzer that attaches to a network to monitor, record, analyze, and interpret network transmissions. Monitoring and analysis functions are separate, menu-driven activities that provide high-level analysis and troubleshooting for complex local and wide-area network installations. SNAP (Subnetwork Access Protocol) Sometimes called Subnetwork Access Convergence Protocol. An extension to IEEE 802.2 LLC that permits a station to have multiple Network layer protocols. The protocol specifies that DSAP and SSAP addresses must be AA hex. A field subsequent to SSAP identifies one specific protocol. Interpreted in the TCP/IP PI suite and the AppleTalk PI suite. SNMP (Simple Network Management Protocol) Interpreted in the TCP/IP suite.
SNRM (set normal response mode) Places a secondary station in a mode that precludes it from sending unsolicited frames. The primary station controls all message flow. Used in SDLC. SNRME (set normal response mode [extended]) trol field. Used in SDLC. SNRM with two more bytes in the con-
socket A logically addressable entity or service within a node, serving as a more precise identification of sender or recipient. source address The part of a message that indicates from whom the message came.
spanning tree A method of creating a loop-free logical topology on an extended LAN. Formation of a spanning tree topology for transmission of messages across bridges is based on the industry-standard spanning tree algorithm defined in IEEE 802.id. spanning-tree algorithm An algorithm used to create a spanning tree.
spanning-tree protocol A bridge protocol that utilizes the spanning-tree algorithm. This enables a learning bridge to dynamically work around the loops in a network topology by creating a spanning tree. Bridges exchange BPDU messages with other bridges to detect loops. They then remove loops by shutting down selected bridge interfaces.
Appendix D GLOSSARY
459
SPF (shortest path first) A routing algorithm that iterates on length of a path to determine the shortest path spanning tree. SPID (service profile identifier) A number that some service providers use to define the services to which an ISDN device subscribes. split horizon A routing rule that states a router cant send routing information about a network out of the same interface from which it learned that information. SPX (Sequential Packet Exchange) Novells version of the Xerox protocol called SPP. Interpreted in the Novell NetWare PI suite. SQE (signal quality error) The 802.3/Ethernet collision signal from the transceiver.
SQE Test The SQE signal generated by the transceiver at the end of a transmitted frame to check the SQE circuitry, (also known as heartbeat in Ethernet). SQL (Structured Query Language) SQL server Used to access databases.
A server that understands Structured Query Language.
SR/TLB (source-route translational bridging) A method of bridging in which source route stations can communicate with two transparent bridge stations with the help of an intermediate bridge that translates between the two bridge protocols. SSAP (source service access point) station. The LLC SAP for the protocol used by the originating
SSE (silicon switching engine) A routing and switching mechanism that compares the Data Link or Network layer header of an incoming packet to a silicon switching cache, determines the appropriate action, and forwards the packet to the proper interface. It can perform switching independent of the system processor. SSP (1) (silicon switch processor) A high-performance silicon switch for Cisco 7000 series routers that provides distributed processing and control for interface processors. (2) (switchto-switch protocol) A protocol specified in the DLSw standard that routers used to establish DLSw connections, forward data, locate resources, and handle flow control and error recovery. S/T Interface static route In ISDN, the connection between a BRI interface and an NT1 device. Route that is explicitly configured and entered into the routing table.
store and forward packet switching A packet switching technique in which frames are fully buffered and processed before being forwarded out the appropriate port. This includes calculating the CRC and checking the destination address. Bridges and switches using this method verify the frame prior to forwarding it. If a frame has been damaged, that frame is not forwarded. Store and forward devices isolate collision domains. STP (shielded twisted pair) A two-pair wiring medium used in a variety of network implementations. See also Spanning-Tree protocol. stub area An OSPF area that carries a default route, intra-area routes, and inter-area routes, but does not carry external routes.
460
TCP/IP PRIMER PLUS
stub network
A part of an internetwork that can be reached by only one path.
SUA (stored upstream address) The network address of a Token-Ring stations nearest upstream neighbor. Texas Instruments calls this the UNA. subinterface One of a number of virtual interfaces on a single physical interface.
subnet A term used to denote any networking technology that makes all nodes connected to it appear to be one hop away. In other words, the user of the subnet can communicate directly to all other nodes on the subnet. A collection of subnets together with a routing or network layer combine to form a network. subnet address mask. A portion of an IP address that is specified as the subnetwork by the subnet
subnet mask A 32-bit number associated with an IP address; each bit in the subnet mask indicates how to interpret the corresponding bit in the IP address. SVC (switched virtual circuit) A virtual circuit set up on demand, as in the case of a dialup telephone line or an X.25 call. switch (1) A network device that filters, forwards, and floods frames based on the destination address of each frame. (2) An electronic or mechanical device that enables a connection to be established as necessary and terminated when there is no longer a session to support. symptom An abnormal or unusual network event indicative of a possible network problem.
SYN (synchronized) (1) The synchronized bit in a TCP segment used to indicate that the segment is a SYN segment. (2) The first segment sent by the TCP protocol; used to synchronize the two ends of a connection in preparation for opening a connection. synchronous transmission A method of data transfer in which information is transmitted in blocks (frames) of bits separated by equal time intervals. Syslog A service that receives messages from applications on the local host or from remote hosts that have been configured to forward messages.
T
T1 T3 A digital transmission link with a capacity of 1.544Mbps. A digital transmission link with a capacity of 44.736Mbps. An external connection to a PC or another device. TA (terminal adapter)
TACACS (Terminal Access Controller Access Control System) An authentication protocol that provides remote access authentication and related services such as event logging. Uses user passwords. TCP (Transmission Control Protocol) The connection-oriented byte-stream protocol within TCP/IP that provides reliable end-to-end communication by using sequenced data sent by IF Interpreted in the TCP/IP PI suite. .
Appendix D GLOSSARY
461
TCP/IP (Transmission Control Protocol/Internet Program) A suite of networking protocols originally developed by the U.S. government for ARPANET and now used by several LAN manufacturers. The individual TCP/IP protocols are listed separately in this glossary. Telnet Protocol for transmitting character-oriented terminal (keyboard and screen) data. Interpreted in the TCP/IP suite. terminal A simple device, such as a computer, at which data can be entered or retrieved from the network. terminator A resistive connector used to terminate the end of a cable or an unused tap into its characteristic impedance. The terminator prevents interference-causing signal reflections from the ends of the cable. TFTP (Trivial File Transfer Protocol) A protocol within TCP/IP used to exchange files between networked stations. Interpreted in the TCP/IP PI suite. throughput The quantity of data successfully transferred between nodes per unit of time, usually seconds. THT (token holding timer) The maximum length of time a station holding the token can initiate asynchronous transmissions. The THT is initialized with the value corresponding to the difference between the arrival of the token and the TTRT (FDDI). token A small message used in some networks to represent the permission to transmit; it is passed from station to station in a predefined sequence. token bus A type of LAN in which all stations can hear what any station transmits and in which permission to transmit is represented by a token sent from station to station. Token-Ring A ring-shaped LAN in which each station can directly hear transmissions from only its immediate neighbor. Permission to transmit is granted by a token that circulates around the ring. topology The physical arrangement of network nodes and media within an enterprise networking structure. ToS (type of service) handled. A field in an IP datagram that indicates how the datagram should be
traffic shaping The use of queues to limit traffic congestion on a network. Data is buffered and then sent into the network in regulated amounts, ensuring that traffic will fit within the promised traffic envelope for the particular connection. transparent bridging A bridging scheme in which bridges pass frames one hop at a time based on tables associating end nodes with bridge ports. Often used in the Ethernet network. Transport layer Layer 4 of the OSI Reference Model. The Transport layer is responsible for reliable network communication between end nodes. It implements flow and error control and often uses virtual circuits to ensure reliable data delivery. trap A message sent by an SNMP agent to an NMS, console, or terminal indicating the occurrence of a significant event.
462
TCP/IP PRIMER PLUS
tree topology A LAN topology similar to a bus topology. Tree networks contain branches with multiple nodes. TSR (Terminate and Stay Resident) A DOS program that, once loaded into RAM, remains there in the background until unloaded or power is shut off. TTL (time to live) valid. A field in an IP header that indicates how long a packet is considered
tunneling An architecture that provides a virtual data link connection between two similar networks through a foreign network. twisted pair A relatively low-speed transmission medium consisting of two insulated wires arranged in a regular spiral pattern. The wires can be shielded or unshielded.
U
UA (unnumbered acknowledgment) or DISC request. An LLC frame that acknowledges a previous SABME UDP (User Datagram Protocol) A protocol within TCP/IP for sending unsequenced data frames not otherwise interpreted by TCP/IP. UI (unnumbered information) without sequence numbers. U Interface An LLC, HDLC, or SDLC frame type used to send data
The connection between an NT1 device and the ISD network.
UNA (upstream neighbor address) The network address of a Token-Ring stations nearest upstream neighbor. IBM calls this the SUA. UNI (User-to-Network interface) An ATM forum specification defining an interoperability standard for the interface between ATM-based products located in a private network and ATM switches located in the public carrier networks. unicast A message sent to a single network destination. An address that specifies a single network device.
unicast address UNIX
A popular portable operating system written by AT&T. The percentage of the total capacity of a network segment.
utilization
UTP (unshielded twisted pair) A four-pair wire medium used in a variety of networks. UTP does not require a fixed spacing between connections.
V
V.24 An ITU-T standard for Physical layer interfaces between DTE and DCE.
Appendix D GLOSSARY
463
V.25bis An ITU specification that describes procedures for call setup and teardown over the DTE-DCE interface in a PSDN. V.32 An ITU-T standard serial-line protocol for bi-directional data transmission. An ITU-T standard that extends V.32 to speeds of up to 14.4Kbps.
V.32bis V.34 V.35
An ITU-T standard that specifies a serial-line protocol. A CCITT wideband interface recommendation for WANs.
VC (virtual circuit) A logical circuit created to ensure reliable communication between two network devices. A virtual circuit can be either permanent or switched and is used in frame relay and X.25. In ATM virtual circuits are called virtual channels. VINES (Virtual Network Software) The networking operating system developed by Banyan Systems, Inc. and the protocols used therein. Notable components are StreetTalk and Net RPC. virtual circuit A communications link that appears to be a dedicated point-to-point circuit.
VLAN (Virtual LAN) A logical, rather than physical, grouping of devices. Devices are grouped using switch management software so that they can communicate as if they were attached to the same wire, when in fact they might be located on a number of different physical LAN segments. VLSM (variable length subnet mask) The capability to specify a different subnet mask for the same network number on different subnets. VLSM can help optimize available address space. VPN (virtual private network) Enables IP traffic to travel securely over a public TCP/IP network by encrypting all traffic from one network to another. A VPN uses tunneling to encrypt all information at the IP level. VT (virtual terminal) An entity that is part of the Application layer protocol and enables an application to interact with a terminal in a consistent manner independent of the terminal characteristics.
W
WAN (wide area network) A collection of LANs, or stations and hosts, extending over a wide area that can be connected through common carrier or private lines. Typically, transmission speeds are lower on a WAN than on a LAN. WFQ (weighted fair queuing) A method of queuing that prioritizes low-volume traffic over high-volume traffic to ensure satisfactory response time for common user applications. wildcard mask A 32-bit quantity used in conjunction with an IP address to determine which bits in an IP address should be ignored when comparing that address with another IP address. A wildcard mask is specified when setting up access lists.
464
TCP/IP PRIMER PLUS
window The number of data segments the sender is allowed to have outstanding without receiving an acknowledgment. windowing A method to control the amount of information transferred end to end, using different window sizes. WINS (Windows Internet Naming Service) Enables clients on different IP subnets to register dynamically and browse the network without sending broadcasts. workgroup A collection of workstations and servers on a LAN designed to communicate and exchange data with one another. WWW (World Wide Web) A large network of Internet servers providing hypertext and other services to terminals running client applications. WWW browser A GUI-based hypertext client application, used to access hypertext documents and other services located on remote servers throughout the WWW and Internet.
XY
X.25 A CCITT recommendation that defines the standard communications interface for access to packet-switched networks. XID (exchange identification) An LLC unnumbered frame type used to negotiate which LLC services will be used during a connection. XNS (Xerox Network Systems) the Internet Transport Protocols. A family of protocols standardized by Xerox; particularly
X Window Protocol for the management of high-resolution color windows at workstations. Originated by MIT, DEC, and IBM, and subsequently transferred to a consortium of vendors and developers.
Z
ZIP (Zone Information Protocol) Used in AppleTalk to maintain an Internet-wide mapping of networks to zone names. ZIP is used by the Name Binding Protocol (NBP) to determine which networks belong to a given zone. Interpreted in the AppleTalk PI suite. Zone In AppleTalk networks, a set of one or more nodes within an internet.
APPENDIX E
ANSWERS
Chapter 1
1. The major objective of the OSI model is to define a vendor-neutral framework for communication. This allows coexistent communication between similar and dissimilar protocols, hardware, operating systems and network architectures. 2. Session layer. 3. Although the Transport layer usually is described by these characteristics it really depends on what protocol is used at this layer. For instance, if TCP is used, the question is absolutely true. If UDP is used, no part of the question is true. 4. Layer two of the OSI model, the Data Link, is where switches and bridges exist. Switches and bridges use layer two (MAC addresses) to make forwarding decisions. 5. Network layer. 6. Process/Application, Host-to-Host, Internet, network access. 7. CRC calculation and verification, and media access are two examples. 8. UDP.
Chapter 2
1. Class A (1-127), Class B (128-191), Class C (192-223), Class D (224-239), Class E (240-247). 2. Subnet masks determine whether a destination is local, which tells the source host whether it can deliver the datagram itself or send it to a gateway for forwarding. The subnet mask of the source host is compared to the destination hosts IP address using bitwise ANDing to determine what portion of the address defines the network. 3. Network layer addresses are logical and represent the Layer 3 4-byte IP address of the host. These addresses are assigned either manually or dynamically. 4. 255.255.255.255 signifies a networkwide message sent to all nodes and all networks. Used for broadcast purposes, 0.0.0.0 is an unknown network or host that typically is used to define a default gateway or last resort. 127.0.0.1 is used for internal loopback
466
TCP/IP PRIMER PLUS
testing. The following private addresses are used within a companys network typically to facilitate better IP addressing implementation. These addresses may not be used out on the Internet. Companies implementing these addresses must use NAT to allow for translation to a registered address that may be used out on the Internet: 10.0.0.010.255.255.255, 172.16.0.0172.31.255.255, 192.168.0.0192.168.255.255. 5. 8 bits. 6. 14 subnetworks and 14 hosts. 7. 255.255.255.224. 8. 126 subnets and 510 hosts. 9. 5 bits, which would allow up to 30 hosts. 10. 10 bits, which would allow 1022 hosts. 11. 182 (128+32+16+4+2+1) 12. 11001001 (128+64+8+1) The Binary equivalent of 201 is 11001001 be it a decimal or a subnet mask.
Chapter 3
1. IP. 2. ICMP echo (type 8) and reply (type 0). 3. It packages it as datagrams, including the source and destination Network layer IP addresses. 4. An IP header has a minimum of 20 bytes unless options are present. The IP header fields within that 20 bytes are version, header length, type of service, total length, identification, flags, fragment offset, time to live, protocol, checksum, source address and destination address. Other headers include options and data. The question asks which fields are in that header. I assume this is the protocol type field with 0800, but you may want to mention what field it is. 5. It is used by applications to specify a level of routing service it would like a router to use when it forwards datagrams. 6. The identification and fragment offset fields. 7. ICMP type 3 is a destination unreachable. If this message is received it means the requested destination network, host, or port is either too far or not available. 8. A type 3 ICMP message is Destination Unreachable. A type 3 ICMP message with an error code of 4 signifies that a fragmentation is needed, but dont-fragment bit set error has occurred.
Appendix E ANSWERS
467
9. This means the requested host is unreachable. 10. Type 11; this means the TTL timer has expired (reached a value of 0).
Chapter 4
1. ARP performs logical Network layer-to-Data Link hardware address resolution. ARP resolution is broadcast based. 2. RARP performs Data Link hardware address to logical Network layer address resolution. RARP is used by end devices to retrieve their IP addresses and configuration parameters from a RARP server. Requests and responses are broadcast based. 3. BootP replaced RARP. The main difference between BootP and RARP is that gateways or relay agents cannot forward RARP requests and responses. 4. The main difference between DHCP and BootP is that DHCP does not use a static mapping table. DHCP can support static and dynamic address mappings. 5. Depending on implementation, hosts can use these three mechanisms to remove old or invalid entries from the ARP table: timeout, unicast poll, and Link layer or higher layer device. 6. Proxy ARP allows a device, such as a gateway, to respond to ARP requests on behalf of a remote host. 7. The Opcode field defines the type of ARP or RARP operation being performed. An Opcode value of 1 equals a ARP request, 2 equals an ARP reply, 3 equals a RARP request, and 4 equals a RARP reply. 8. When a host wants to communicate with a remote device it compares the destination hosts IP address to the source hosts local subnet mask to determine whether the remote host resides on the local segment. If the source host determines the destination resides on the same subnet, it might shout (send a local ARP). If not, it must route (send a local ARP to resolve the gateways hardware address) to forward future datagrams. 9. DHCP has seven message types: discover, offer, request, ACK, NAK, decline, and inform. 10. The four DHCP message types that accomplish the initial four-phase configuration process between client and server are discover, offer, request, and ACK.
Chapter 5
1. Directly connected interface, static, default, or dynamic. 2. Manual entry of each route in the route table by an administrator, no route update traffic, ideal for point-to-point WAN links or dial-up networks, can use as backup when primary link fails, impractical to have entire network static, disadvantage of extreme administrative overhead, better to implement on small networks.
468
TCP/IP PRIMER PLUS
3. Broadcast, classful routing (updates do not include the subnet mask), timers control updates, the entire table is always sent regardless of a change, subject to routing loops, best used in small to medium networks, maximum distance defines the diameter of the network, uses hops as its sole metric. 4. You would want to use static routing in small networks or point-to-point links. If you want to entirely eliminate route update traffic, use static routing. You would use dynamic routing if you want your routers to automatically detect and adjust around failed links or routers. 5. Default routing provides a route to be used as a last resort, when no other route to a destination exists. 6. IGP and EGP. 7. IP RIPv1, IP RIP v2, IGRP, EIGRP, and OSPF . 8. IP RIPv1, IP RIP v2, and IGRP. 9. Hops; IP RIP has a maximum hop count of 15. IGRP has a maximum hop count of 255. 10. Count to infinity, holddowns, split horizon, poison reverse. 11. Split horizon prevents routing loops by preventing routing information from being advertised out the same interface on which it was received. 12. Bandwidth, delay, reliability, load, and mtu. 13. OSPF .
Chapter 6
1. RIP is considered to be an IGP and a distance vector routing protocol. 2. RIP has the following characteristics: broadcast based, IGP, works best on small-sized networks, and distance-vector routing protocol. 3. RIP uses shortest distance, measured in hops. 4. Routers broadcast their entire routing table every 30 seconds. 5. 25 6. 15 7. Multicast, authentication, VLSMs (classless routing). 8. Version 2 is backwards compatible to Version 1 and Link State protocols are more proficient. 9. RIPv1 has the following disadvantages: broadcast based, sends out the entire table even when no changes occur, slow convergence due to periodic timers, maximum distance
Appendix E ANSWERS
469
limitation of 15 hops, prone to routing loops and classful routing protocol (does not support VLSM). 10. RIP uses count to infinity, holddowns, split horizon and poison reverse. 11. RIP employs holddown, invalid and periodic update. 12. OSPF is considered to be an IGP and link state routing protocol. 13. Link capacity, load, MTU, reliability and delay. 14. OSPF has the following advantages over RIP: ability to configure hierarchical routing domains, ability to adapt quickly to internet changes, only sends topology changes in updates when changes occur, supports large networks, supports load balancing, authentication of routing tables exchanges, supports VLSMs and uses multicasting. 15. OSPF has the following features: multicasting, fast convergence, triggered updates, classless routing, ToS or QoS, authentication, equal and unequal cost routes and can implement single or multiple areas. 16. Adjacency (neighbor table), link state (topology table), and forwarding (route table). 17. It is a routers neighbor table. If a router has not formed an adjacency with their neighbor, they cannot exchange routing information. 18. It is a complete map of the internetwork topology. 19. A forwarding database is a local route table that has a table of the best route to forward traffic. 20. OSPF uses LSAs to form their link state database and to communicate within an area or out of an area. 21. An OSPF Intra-Area Advertisement are only sent by routers to other routers within a specific area and an Inter-Area Advertisement are sent by ABR routers to other routers in directly connected areas. 22. Down, Init, Exstart, Exchange, Loading, and Full. 23. Internal, Backbone, ABR, ASBR. 24. Type 0. 25. Hello, database description, link state request, link state update and link state acknowledgement. 26. Hello packets establish and maintain adjacencies. 27. An OSPF Database Description packet summarizes database content. 28. IGRP can use a combination of metrics including: bandwidth, internetwork delay time, reliability and load. 29. A maximum hop count of 255 allows for support of larger networks.
470
TCP/IP PRIMER PLUS
30. Update, invalid, holddown, flush timer. 31. EIGRP has the following features: faster convergence through triggered updates, VLSMs, supports multiprotocol, keeps backup paths in route table, supports ToS or QoS, uses cost-based metrics like IGRP and multicast or unicast. 32. EIGRP is considered a balanced hybrid protocol. 33. It has the advantage of allowing a company to run multiple protocols but maintain one routing table, but has the disadvantage of limiting you to Cisco equipment. 34. The best route is consider the successor and the backup is considered a feasible route. 35. Hello/ACKs, updates, queries, replies, and requests. 36. An EGP connects independent ASs together while an IGP connects an independent AS. 37. VLSMs, route aggregation, and CIDR. 38. You would want to implement BGP in the following situations: if you have multiple exit points connecting to a single ISP, if you have multiple paths to different ISPs and would like to dictate traffic, you need intelligent path selection and specific criteria, or your networks infrastructure is used as a transit area for other organizations traffic. 39. A full-mesh topology requires separate logical TCP connections between all BGP routers within the same AS, allowing gateways to quickly determine whether a loop exists and pruning it. A partial mesh topology does not require all routers to maintain logical connections with one another. 40. BGP speakers, peers, internal peers and external peers. 41. Route information received, route information to be advertised, their local BGP table. 42. TCP. 43. Open, update, keepalive, notification. 44. The open message initiates a BGP peer relationship between internal or external peers. 45. Notification messages (message type 3) occur when BGP routers encounter an error. These messages cause the TCP session to be torn down. 46. Path attributes. 47. Well-known mandatory, well-known discretionary, optional transitive, optional nontransitive. 48. When multiple paths exist to route traffic outside of this AS, routers within an AS may set the local preference value higher for one path, indicating the preferred route. 49. BGPv4 supports VLSMs, summarization and local preference while BGPv3 does not. In addition, BGPv4 supports both full and partial mesh while v3 supports only full.
Appendix E ANSWERS
471
Chapter 7
1. Controls end-to-end communication between two processes running on different hosts, provides connection-oriented or connectionless services to upper layers, uses client and server port address to identify processes running within a host, segments data for upperlayer applications. 2. All connection-oriented protocols exhibit these characteristics: session setup, session teardown, acknowledgements, sequencing, flow control, keepalives, reliable/guarantee delivery, slower delivery of data, tons of overhead, error recovery and retransmission of data. 3. Well-known server ports define well-known programs used in the industry that have become the official standard for addressing such programs. They have a range of 0-255. 4. Lesser-known server ports are reserved ports that vendors can implement on an asneeded basis and have a range of 256-1023. 5. Client ports are variable (or ethereal) ports made up on the fly each time a client process begins and opens a new port and have a range of 1024-65536. 6. The client and server ports clearly identify the process communicating on each box. By linking the sending hosts address and port to the destination hosts address and port, TCP or UDP can manage the communication between these hosts and their processes, and distinguish them from other virtual connections to the same hosts. 7. UDP offers fast, unreliable delivery of messages between applications running on remote hosts. TCP offers slower but guaranteed delivery of data. 8. It is an alert to the sending host to slow down transmission or stop altogether. 9. They have to choose between speed (UDP) and reliability (TCP). 10. TCP utilizes acknowledgements and sequencing to help keep track of data and guarantee delivery.
Chapter 8
1. During TCP operation, TCP uses connection setup and teardown, multiplexing, data transfer, flow control, reliability, and precedence and security to control the communications between remote host process. 2. TCP must establish a logical circuit or session between communicating ports before upper-layer applications can exchange meaningful data. 3. Multiplexing enables TCP to establish and maintain multiple communication paths between two hosts simultaneously. 4. TCP receives datastreams (messages) from upper-layer applications and organizes them into segments to be passed down to the Network layer to become a datagram.
472
TCP/IP PRIMER PLUS
5. Windowing controls the inbound flow of data. 6. TCP provides reliable delivery of packets through sequencing and acknowledgements. 7. Connection-oriented protocols have six basic characteristics: session setup, sequencing, acknowledgements, keepalives, session teardown, and flow control. 8. Socket pairing is the combination of the source and destination hosts Network layer IP addresses and Transport layer port addresses. 9. Retransmission occurs after a logical circuit (TCP connection) is established between remote host processes. 10. The TCP header contains source port, destination port, acknowledgement number, data offset, reserved, control flags, window, checksum, urgent point and TCP options fields.
Chapter 9
1. RFC 768 defines UDP. 2. UDP provides connectionless, unreliable, fast delivery of data for applications running on remote hosts. 3. Protocol type 17 identifies UDP in the IP header. 4. UDP does not utilize sequencing and acknowledgements to guarantee delivery of data. It relies on other protocols to perform this function. It simply identifies the source and destination ports, sends the data, and hopes it arrives at the destination. 5. During UDP operation of transferring data, UDP assumes that there is a stable and reliable network infrastructure supporting the transmission of data. It relies on other protocols to detect and correct errors. 6. UDP has no management responsibilities for maintaining a connection. UDP does not establish a connection between hosts; therefore, it does not need to maintain a connection. 7. UDP offers speedier delivery of packets and less overhead than TCP. 8. UDP uses CRC (Cyclic Redundancy Check), which checks for damaged frames in the UDP header, upper-layer data and pseudo IP header. 9. The checksum validates the UDP header, upper-layer data, and pseudo IP header. 10. The pseudo IP header contains the source and destination Network layer addresses, Transport layer protocol type code, and UDP length value.
Appendix E ANSWERS
473
Chapter 10
1. Application, Presentation, and Session. 2. To provide access to resources and services on remote hosts, file transfer (FTP or TFTP), file and print operations, e-mail. 3. FTP and TFTP. 4. Providing a common data format across different platforms. 5. Coordinates dialogs between two applications. 6. NFS (application layer), XDR (presentation), and RPC (session).
Chapter 11
1. Enables a user running a client terminal session to access a remote host (or Telnet server) across TCP/IP Internets. 2. When the user starts the Telnet session, an application on the users machine becomes the client. The client establishes a TCP connection with a Telnet server (remote host) using the standard TCP three-way handshake as described in Chapter 8, Transmission Control Protocol (TCP). The client communicates over the TCP connection from the users keyboard and display as if connected directly to the remote hosts terminal. The server utilizes a pseudo terminal device. The pseudo terminal device describes the operating system entry point that enables a program like Telnet to transfer data to another operating system as if coming from the same keyboard. 3. Used for negotiating parameters between clients and servers. 4. Binary transmission, echo, suppress go ahead, status, timing mark, terminal type, end of record, window size, terminal speed, remote flow control, line mode, environment variables. 5. Network Virtual Terminal (NVT)Provides a standard interface to remote systems, allows clients and servers to negotiate various options and symmetric view of terminals and processes. 6. The NVT provides transparency and support for a minimum level of options between remote clients and servers being used by either side. By implementing a virtual terminal as a front end, this hides the differences between the communicating devices and provides a common set of commands and characteristics. 7. Characters and display device. 8. Either side can request the use of an optional feature. If the other side does not support the feature or is prohibited from allowing this feature to be used, it rejects the request. Both sides agree upon and use the supported features, and keep all other options at the minimum NVT standard.
474
TCP/IP PRIMER PLUS
9. Interpret As Command. 10. WILLSender wants to enable the option, DOSender wants the receiver to enable the option, WONTSender wants to disable the option, DONTSenders wants the receiver to disable the option. 11. WILL/DO, WILL/DONT, DO/WILL, DO/WONT, WONT/DONT, and DONT/WONT.
Chapter 12
1. FTP allows a remote or local client and server to efficiently transfer files or data using TCPs reliable transport: promote sharing of files (computer programs or data), encourage indirect or implicit use of remote computers, shield a user from variations in file storage systems among hosts, and transfer data reliably and efficiently. 2. User InterfaceProvides a user interface and drives the client protocol interpreter. Client PIThe client protocol interpreter. Issues commands to the remote server protocol interpreter and drives the client data transfer process. Server PIThe server protocol interpreter. Responds to commands from the Client PI and drives the server data transfer process. Client DTPClient data transfer process. Communicates with server data process and local file system. Server DTPServer data transfer process. Communicates with client DTP and the remote file system. 3. Protocol interpreter deals with the commands and replies. 4. The server PI listens on well-known port number 21 for control connection requests and waits for a client communication. The client PI initiates the connection by sending a TCP SYN request in the form of a control message addressed to the destination TCP on wellknown port 21. 5. Ports 20 (data) and 21 (control). 6. Data representationIdentifies the type of data being sent. Data structureSpecifies the format of the data being transferred. Transmission modeSpecifies how the data transmits across the connection. 7. ASCII (default), EBCDIC, Image file type (also called binary), Local file type. 8. FTP can use three types of data structure: File (default), Record, Page. 9. Stream (default), Block, Compressed. 10. Nonprint, Telnet format command, Fortran carriage control.
Appendix E ANSWERS
475
11. Stream mode as the following characteristics: default mode, data transmitted in a stream of bytes, and allows record structures. 12. The server and client protocol interpreters communicate commands and replies across the control connection as NVT ASCII (Telnet) strings. FTP commands come in the following three categories: access control, transfer parameter and service. 13. FTP replies appear as three-digit numbers with an optional message in the form of text following the number string. The FTP reply format enables both the interactive user and the software to read the replies, providing information explaining the response. FTP replies guarantee synchronization of requests and actions during file transfer and that the user always knows the state of the server. 14. Transfer files through the Internet without having a specific user account through anonymous FTP. This means you do not have to be an official user of a particular system to gain access to files that system offers.
Chapter 13
1. Simple Mail Transfer Protocol (SMTP) provides the exchange of electronic mail (e-mail) between a sender (client) and receiver (server). 2. Users have immediate interaction with the e-mail system through the UA. Through the UA the user composes, submits, and receives e-mail messages. 3. SMTP facilitates the delivery of mail messages (known as a Message Transfer Agent or MTA) between remote client and server mail applications (known as User Agents). 4. SMTP has the following limitations: the message must contain only ASCII characters, the maximum line length must not exceed 1000 characters, and the message must not exceed a predefined maximum size. 5. SMTP has the following rules: a command code and an argument make up each SMTP command, four alphabetic characters in either upper- or lowercase comprise the command code, one or more space characters separate this code from the argument, path arguments are case sensitive, CRLF concludes argument field and square brackets enclose optional arguments. 6. SMTP clients and servers use the three digits to communicate receipt of information and notify the other side when it has encountered an error. 7. SMTP replies include a three-digit number code meant for the computer and text for the user. The user can then use this information to determine the status of his or her request. 8. MIME extensions provide for transmissions of data previously unsupported in Internet mail by encoding the message into readable ASCII to create a standard e-mail message.
476
TCP/IP PRIMER PLUS
Chapter 14
1. The namespace has the following problems: It makes expansion difficult, work overload complicates the expansion problem, and it is both inefficient and costly. 2. The primary name server loads information from the disk files. The secondary server gets information from the primary. 3. Because computers use numbers (for example, IP addresses and MAC addresses) for addressing, not a name, a method, such as DNS, needs to exist for name resolution. 4. It uses a hierarchical system starting with top-level domain names, then breaking it up into lower-level domains that are more specific. 5. Caching means to store information in RAM. Name servers store all of the information requests (mappings) by filing them away (saving to disk) or caching them (saving to RAM). This way, it keeps up on the most recently requested data and has the newly requested name resolutions. Caching also lowers the cost of resolving nonlocal names because of its speed. 6. If the server still cannot find the answer after checking its cache, it becomes a client (acting as a proxy for the source host) and uses a message format to ask multiple questions to the authoritative server in one message. 7. Each message contains three things: A domain name to be resolved The class, or protocol family the domain name uses The type of the domain name 8. NetBEUI is strictly a Layer 2 protocol implementation designed to carry NetBIOS datagrams over a flat-bridged network. NetBIOS is a datagram and naming service. 9. Modifications to NetBIOS allow it function at layer three by utilizing TCP/IP. 10. 37,138 and 139 11. NetBIOS has the following node types: B-node (broadcast node type)Tries broadcast, then LMHosts file. P-node (point-to-point node type)Tries NBNS server only. M-node (mixed node type)Client tries b-node, p-node, then LMHosts file. H-node (hybrid node type)Client tries p-node, b-node, then LMHosts file. 12. Intercept local resolution broadcast requests and relay them as directed datagrams to a remote WINS server for name resolution.
Appendix E ANSWERS
477
Chapter 15
1. You need to use the HTTP protocol to find a Web page that you want. You can visibly see HTTP in the first part of the URL. 2. HTTP makes communication between your workstations browser and a Web server happen. 3. Your browser works as an application program and opens Web pages. 4. HTTP works at the application level focusing on providing a communication link and message forward. It does not offer reliability or perform retransmission. 5. HTTP has the following qualities: bi-directional transfer, capability negotiation, support for intermediaries, supports caching, does not keep a history of HTTP sessions or your HTTP requests, and works at application level to provide a communication link and message forward. 6. HTTP supports caching. This means that to save time, your browser caches a copy of each Web page it retrieves for you. If you want this page again, HTTP has the browser ask the server whether the contents of the present page differ from the cached copy. 7. Works as an intermediary HTTP host functioning as either an HTTP client or server so the UA and the Origin server can exchange information. Proxy agents pass requests from clients to servers. Servers also respond to the request itself when the information you want is local. 8. Any machine along the path between the browser and the server can be a proxy server. 9. HTTP has the following general message format: a generic start line, called a request line for request messages and a stats line for reply messages, a general header, a message header, one empty line and the message body. 10. The message body is for you to read. 11. The header messages are for the browser to read. 12. Error messages give you an indication as to what type of error was encountered and what went wrong with the delivery.
Chapter 16
1. FTP runs on top of TCP making it connection oriented; TFTP runs on top of UDP making it connectionless. 2. It is a simple and fast file transfer protocol with little overhead. 3. Fast, unreliable connectionless file transfer. 4. The sending side (TFTP client) opens a variable client UDP port (referred to as a TFTP or transfer ID), requests a file, and waits for the acknowledgement of each block before
478
TCP/IP PRIMER PLUS
sending another block. In turn, the receiving side acknowledges each block when it receives the data. 5. HTTP uses the following five packets: read request, write request, data, acknowledgement, and error. Read request and write request files begin a request and determine what file needs to be transferred. Data packets transfer the requested data. The ACK packet acknowledges the receipt of each block (data packet) received during data transfer. The error packet acknowledges any of the other packet types and signifies that an error has occurred. 6. The end of a file transfer. 7. TFTP utilizes the lock-step acknowledgement method, which means that each data packet has to be acknowledged before transmission of another. Remember TFTP transmits data in blocks one at a time with the first data block numbered one. 8. The following three things trigger an error packet: the host cannot satisfy a request, the host receives a delayed or duplicated packet, and when the host loses access to a resource. 9. If the client makes a read request, the server begins the transfer. If the client makes a write request, the client begins the transmission. 10. The TFTP client initiates the connection by requesting to read or write a file from or to the server. The client does this by opening a variable port (TFTP TID) to the receivers well-known TFTP server port 69. The client specifies the identification of the file name and data type within the initial request. Once the client sends the initial request, the TFTP server reassigns itself a new UDP port to use as its TID for the duration of this data transmission and the transfer begins. 11. The blocksize option allows for larger datagrams to be exchanged. A larger blocksize increase the file transfer performance between remote hosts. 12. Servers that support option negotiation have an option acknowledgement (OACK) packet to notify the client if it supports this option. When a server accepts the option, it includes it in the OACK packet. If it does not accept the option it simply ignores it, leaving it out of the OACK frame. Clients implement only what servers allow. The client might request multiple options during the negotiation process by simply listing them within the read or write packet. The client appends the option request to the standard read or write request used to initialize the session between the client and server. 13. The OACK packet is an option acknowledgment of a negotiated option.
Chapter 17
1. SGMP. 2. Agents, managers, and proxies.
Appendix E ANSWERS
479
3. SNMP agents run SNMP responder and notification generation software. 4. SNMP proxies provide message forwarding between agents and managers. Proxies also act as an intermediary between agent hosts using different versions of SNMP, which allow compatibility between the hosts. 5. As hosts, SNMP managers run management control software used to remotely control and monitor SNMP agents. These hosts provide a central management point and user interface using SNMP to deliver commands to agents. Managers are known as command generators and notification receivers. 6. A trap PDU is an unsolicited message sent by an Agent to an SNMP manager because of a triggered event such as authentication failure.
Chapter 18
1. NFS, RPC, and XDR. 2. NFS provides access to information through distributed file systems over any network architecture. 3. XDR translates and presents data so that two different operating systems can communicate with each other. XDR provides platform independence. 4. RPC provides a protocol and independent interface capable of providing a bidirectional communication link between remote communicating processes. RPC resides at a Session layer, thus it has the responsibility of setting up a session between two host processes, and then maintaining and tracking the session. 5. Sun Microsystems.
INDEX
Symbols
* (asterisk) FTP server commands, 279
Numbers
1 command (RIP), 142 1 hello packets, 174 1 ID value (LSAs), 161 1 link state type (LSAs), 157-158 1Origin type code (well-known mandatory attribute), 195 2AS_path type code (wellknown mandatory attribute), 195 2-byte checksum or Urgent Pointer, 217 2 command (RIP), 143 2 database description packets, 174 2 ID value (LSAs), 161 2 link state type (LSAs), 157-158 3-byte signal circles (Token-Ring), 24 3 command (RIP), 143 3 ID value (LSAs), 161 3 link state request packets, 174 3 link state type (LSAs), 157-159 3Next_Hop type code (wellknown mandatory attribute), 196 4 command (RIP), 143
4 ID value (LSAs), 161 4 link state type (LSAs), 157-159 4 link state update packets, 174 4Multi-Exit-Disc type code (optional nontransitive attribute), 196-197 5 command (RIP), 143 5 ID value (LSAs), 161 5 link state acknowledgement packets, 174 5 link state type (LSAs), 157-160 5Local Pref type code (wellknown discretionary attribute), 196-198 6Atomic_Aggregate type code (well-known discretionary attribute), 197 6-bit control flags, 216-217 7Aggregator type code (optional transitive attribute), 197 7 link state type (LSAs), 157-160 8 total bits (IP headers), 64 9 command (RIP), 143 9 (request) packet, 150 10 command (RIP), 143 10 (response) packet, 150 10Base2 (Slow Ethernet specification), 21 10Base5 (Slow Ethernet specification), 21
10BaseT (Slow Ethernet specification), 21 11 (acknowledgement) packet, 150 11 command (RIP), 143 100BaseFX standard, 22 100BaseT4 standard, 22 100BaseTX standard, 22 100BaseX standards, Fast Ethernet, 22
A
A (RR type), 310 AA (authoritative answer) flag, 307 ABOR command, 279 ABRs LSAs, 3 and 4 link state types, 159 routers, 167 Abstract Syntax Notation 1 (ASN.1), 346 Accept-Charset request headers, 328 Accept-Encoding request headers, 328 Accept-Language request headers, 328 accessing files by NFS clients, 358 ACCT [account-info] command, 278
482
TCP/IP PRIMER PLUS
ACK (acknowledgement) control flag, 216, 224-229 11 packet, 150 hosts, 233 implied, 214 messages, 112 numbers, 214-215 packets, 338 values, 212-214 address classes (IP addressing), 35-40 address family identifier field, RIPv1 headers, 143 Address Mask Reply Type 18, 86 Address Mask Request Type 17, 86 address resolution, 89 Address Resolution Protocol. See ARP addresses agent address (trap PDU field), 351 broadcast, host bits, 52 Class C, route summarization, 53-55 client hardware, 108, 121-122 Data Link layer, 13 destination, IP headers, 73 gateway IPs, 108, 121 hardware, 91, 98, 103 IP, 108, 121, 144, 305 logical, 12 low-level, 299 node, 35 protocols, 98-103 reserved, 39 senders hardware, 99, 104 server IPs, 108, 121 subnet masks, bitwise ANDing, 40-43 subnetting, 44-55 target hardware, 99, 104
adjacency databases, 155, 164 advertisements external, 159-160 inter-area, 158-159 intra-area, 157-158 LSAs (link state advertisements), 156-160 RIP (Routing Information Protocol), 144 advertising router field, 161, 180 agents address (trap PDU field), 351 MTAs (message transfer agents), 291 proxy, 324 SNMP (Simple Network Management Protocol), 347 UAs (user agents), 287-290 aggregation, 52-53 algorithms Bellman-Ford, 138 CRC, 13 cyclical redundancy check (CRC), 9 DUAL (Diffusing Update Algorithm), 184 FCS, 13 frame check sequence (FCS), 9 LSA (Link State Algorithm), 152 timers, 233-234 allocating configuration information (DHCP), 111 Allow entity headers, 329 ALLO [bytes] command, 279 Aloha Net, 14 American National Standards Institute (ANSI). 25 American Registry for Internet Numbers (ARIN), 35
American Standard Code for Information Interchange (ASCII), 260, 275 ANCOUNT domain server message format, 309 ANSI (American National Standards Institute), 25 ANSI X3T9.5 specification, FDDI (Fiber Distributed Data Interface), 25 answer headers, domain server message format, 309 APIs (Application Programming Interfaces), 314 APPE [pathname] command, 279 Application layer (OSI Reference model), 9-10, 251-253 Application Programming Interfaces (APIs), 314 applications Data Link architecture, 14 UDP (User Datagram Protocol), 243 architectures, Data Link, 14-25, 167 ARCOUNT domain server message format, 309 Area 0, 171-173 area ID field, 174 areas backbone (Area 0), 170 multiple area implementation, 169-170 NSSAs (not so stubby areas), 159 standard (Area 0), 170-171 stub, 171-172 types of, 170 virtual links, 172-173 ARIN (American Registry for Internet Numbers), 35 ARP (Address Resolution Protocol), 40, 89
INDEX
483
broadcast based, 92 cache mechanisms, 94 hardware addresses, 91 headers, 96 hosts, 92-94 Network layer, 89 operation, 91-94 Proxy ARP, 95-96 and RARP (Reverse Address Resolution Protocol), comparing, 101-102 AS (autonomous systems), 138, 169-170 ASBRs, 159-160, 167 ASCII (American Standard Code for Information Interchange), 260, 275 ASN.1 (Abstract Syntax Notation 1), 346 asterisk (*), FTP server commands, 279 ATM (Asynchronous Transfer Mode) protocol, 30 attributes, path, 191, 194-198 authentication field, 175 authoritative name servers, 304 authority, delegation of, 301-304 Authorization request headers, 328 auto file systems (autofs), 359 autocommands, 359 autofs (auto file system), 359 automatic allocation of configuration information (DHCP), 111 automounter, NFS (Network File System) servers, 359 autonomous systems (AS), 138, 169-170
B
backbone areas (Area 0), 170 backbone routers, 167
backup designated router field, 178 bad request error messages, 332-333 balanced hybrid protocols, 184 balanced signaling, 15 balancing loads, 155, 184 Bandwidth metric, 181 Bellman-Ford algorithm, 138 best paths, 129 BGP (Border Gateway Protocol), 137, 187 BGPv3 and BGPv4, comparing, 198 datagrams, 191 external peer routers, 189 full-mesh topology, 189 headers, 191-194 identifier field, 192 IGPs (Interior Gateway Protocols) and EGPs (Exterior Gateway Protocols), comparing, 188-189 internal peer routers, 189 neighbor routers, 189 operation, 190-191 partial-mesh topology, 189 path attributes, 191, 194-198 peer routers, 189 routers, 189-190 speaker routers, 189 BGPv3 and BGPv4, comparing, 198 Bhushan, Abhay, 270 bidirectional transfers, 322 binary numbering system, 33 binary numbers, converting to decimal numbers, 33-34 bits, 13 bit 3, IP headers, 65 bit 4, IP headers, 65 bit 5, IP headers, 65
bit 6, IP headers, 66-67 bit 7, IP headers, 66-67 bits 02 (precedence bits), IP headers, 64-65 determining number of, 45-46 E (options field), 177 hosts in broadcast addresses, 52 parameter field, 308-309 repeating, 23 T (options field), 177 ToS bits (8 total bits), IP headers, 64 bitwise ANDing, 40-43 block transmission mode, 278 boot file names, 109, 122 BOOTP (Bootstrap Protocol), 89, 104-109 Border Gateway Protocol. See BGP breaking up networks, 44 broadcast addresses, host bits, 52 broadcast-based LAN networks, 168 broadcasts ARP (Address Resolution Protocol), 92 NBMA (nonbroadcast multiaccess) networks, 168-169 RARP (Reverse Address Resoution Protocol), 100 browsers (Web), HTTP (Hypertext Transfer Protocol), 323
C
cache mechanisms, ARP (Address Resolution Protocol), 94 cache-control field, 327 caching HTTP (Hypertext Transfer Protocol), 322 IP addresses, resolving, 305
484
TCP/IP PRIMER PLUS
calculations host ranges, 48-51 subnet ranges, 47 call messages, RPC (Remote Procedure Calls), 361-365 capability negotiations, 322 carriage control text, 260 carriage returns, FTP (File Transfer Protocol) commands, 280 Carrier Sense Multiple Access with Collision Detection (CSMA/CD), 16 catchall messages, 85 CD command, 359 CDUP command, 278 Cerf, Vinton, TCP (Transmission Control Protocol), 211 chains, 323-324 channel access methods, 16-17, 24-25 character mode, 258 checksum CRC (Cyclic Redundancy Check), 246 field, 174 ICMP (Internet Control Message Protocol) header or message formats, 76 IP headers, 72-73 LS checksum field, 162 2 bytes, 217 UDP (User Datagram Protocol), 246-247 choke packets, 236 chunking messages, 327 CIDR (class interdomain routing), 52-55 circuit-switched connections, 26-28 circuits demand, 148-150 logical, 219
Cisco EIGRP (Enhanced Interior Gateway Routing Protocol), 133 Snapshot routing, 149 Class A (Slash 8) addresses, 35-40 Class B (Slash 16) addresses, 35-40 Class B networks host range, calculating, 50-51 subnets, 44, 49 Class C addresses, 53-55 Class C (Slash 24) addresses, 35-40 Class D addresses, 36, 39 Class E addresses, 36, 39 class interdomain routing (CIDR), 52-55 class routing, 132 classes, address (IP addressing), 35-40 classful routing, 132, 147 clients DHCP (Dynamic Host Configuration Protocol), 112-119 DTP (data transfer process), 271 dumb terminals, 257 FTP, connections, 272 hardware addresses, 108, 122 IP addresses, 108, 121 NFS (Network File System), 357-358 PI (protocol interpreter), 270-271 proxy agents, 324 redirectors, 251 SMTP (Simple Mail Transfer Protocol), 287 Telnet, 257-258 trees, 357 CMIP (Common Management Information Protocol), 345
CNAME (RR type), 310 code ASCII (American Standard Code for Information Interchange), 260 error, response messages, 330 ICMP (Internet Control Message Protocol) header or message formats, 75-76 Op (operation code), 107 Op (operation code 1 byte), 119 Opcode (operation code), 99, 103, 306 status, response messages, 330-332 three-digit number code, SMTP e-mail replies, 293-294 three-digit numeric code (FTP), 281 code values, 339 collisions, 17 COM domain, 302 commands 1 (RIP), 142 2 (RIP), 143 3 (RIP), 143 4 (RIP), 143 5 (RIP), 143 9 (RIP), 143 10 (RIP), 143 11 (RIP), 143 ABOR, 279 ACCT [account-info], 278 ALLO [bytes], 279 APPE [pathname], 279 autocommands, 359 cd, 359 CDUP, 278 command field, RIPv1 headers, 142-143
INDEX
485
command messages, RIP (Routing Information Protocol), 142 CWD [pathname], 278 DATA, 293 DELE [pathname], 280 EXPN, 293 FTP (File Transfer Protocol), 278-280 HELO, 293 HELP, 293 HELP [string], 280 HFTP, 278-279 LIST [pathname], 280 MAIL FROM, 293 MKD [pathname], 280 MODE [mode], 279 mount, 356 NLST [pathname], 280 NOOP, 280, 293 PASS [password], 278 PASV, 279 PORT [host-port], 279 PWD, 280 QUIT, 279, 293 RCPT TO, 293 REIN, 279 REST [marker], 280 RETR [pathname], 280 RMD [pathname], 280 RNFR [pathname], 280 RNTO [pathname], 280 RSET, 293 SAML FROM, 293 SEND FROM, 293 SITE [string], 280 SMNT [pathname], 279 SMTP (Simple Mail Transfer Protocol), 292-293 SOML FROM, 293 STAT [pathname], 280
STOR [filename], 280 STOU, 280 STRU [structure], 279 SYST, 280 TURN, 293 TYPE [type], 279 USER [username], 279 VRFY, 293 comments, RFCs (Request for Comments), 30-31 Common Management Information Protocol (CMIP), 345 communication chains, HTTP (Hypertext Transfer Protocol), 323 community, SNMP, 348-349 companies, operating systems developed, 3 comparing ARP (Address Resolution Protocol) and RARP (Reverse Address Resolution Protocol), 101-102 BGPv3 and BGPv4, 198 connection-oriented and connectionless protocols, 206-207 Ethernet frame types, 18 Fast and Slow Ethernet, 21 IGPs (Interior Gateway Protocols) and EGPs (Exterior Gateway Protocols), 188-189 Internet and intranets, 31 NetBIOS and NetBEUI, 314 OSPF (Open Shortest Path First) and Distancevector routing protocols, 153 RIPv1 and RIPv2, 151-152 UDP (User Datagram Protocol) and TCP (Transmission Control Protocol), 244
compatibility, RIPv1 and RIPv2, 152 complexity of networking, reducing, 7 components, HTTP (Hypertext Transfer Protocol), 322-323 compressed transmission mode, 278 CON domain, 302 conceptual frameworks, OSI Reference Model, 4 configuration information (DHCP), allocating, 111 congestion, connection-oriented protocols, 234 Connect method tokens, 326 connection field, 327 connection-oriented protocols, 223 and connectionless protocols, comparing, 206-207 flow control, 234-237 keepalives, 234 sequences, 230-234 session setups, 223-227 session teardowns, 227-230 socket pairing, 224-227 TCP (Transmission Control Protocol), 204-206 connectionless protocols, TCP (Transmission Control Protocol), 206 connections, 168, 219, 272 Content-Base entity headers, 329 Content-Encoding entity headers, 329 Content-Language entity headers, 329 Content-Length entity headers, 329 Content-Location entity headers, 329 Content-MD5 entity headers, 330 Content-Range entity headers, 330
486
TCP/IP PRIMER PLUS
Content-Type entity headers, 330 control codes, NVT (Network Virtual Terminal), 260 control flags, 216-217, 224-230 controlling flow, 221 controls, route update traffic, 148 converting binary numbers to decimal numbers, 33-34 core-distribution-access model, static routes, 126 count to infinity (maximum hop count), 130-131 CRC (Cyclic Redundancy Check), 9, 13, 246 CSMA/CD (Carrier Sense Multiple Access with Collision Detection), 16 CWD [pathname] command, 278 Cyclic Redundancy Check (CRC), 9, 13, 246
D
DARPA (Department of Defense Advanced Research Projects Agency), 5 data storing, 360 transferring, 220-221 DATA command, 293 data field, 194 Data Link architecture, 167 applications, 14 Ethernet, 14-22 FDDI (Fiber Distributed Data Interface), 25 standards, 14 Token-Ring, 22-24 Data Link layer (OSI Reference Model), 12-13 data offset, 215
data packets, 338 data representation FTP (File Transfer Protocol), 274-275 data structures, FTP (File Transfer Protocol), 274-277 data transfer process (DTP), clients or servers, 271 data types, 275-276 database description packet type, 174 Database Description packets, 178-179 databases, 155, 164 datagrams BGP (Border Gateway Protocol), 191 Distance-vector routing protocols, 146 IP headers, 62-73 sending by Host A, 43 ToS (Type of Service), 222 user, routing purpose, 125 date field, 327 DDR (dial-on-demand routing), 28 dead interval field, 177-178 decimal numbering system, 33 decimal numbers, binary numbers, converting to, 33-34 decline messages, 112 dedicated (leased) lines, 26-27 dedicated leased-line connections (point-to-point connections), 168 default gateways, 127 default routes, 127 definitions graphic, 323 hyper, 321 routing, 40 shouting, 40 Delay Time metric, 181
delays, propagation, 17 delegation of authority, DNS (Domain Naming System), 301-304 DELETE method tokens, 326 deleting headers or trailers, 9 DELE [pathname] command, 280 demand circuits, 148-150 Department of Defense Advanced Research Projects Agency (DARPA), 5 Department of Defense. See DoD (Department of Defense) Model designated router field, 178 destination addresses, IP headers, 73 destination ports, 213, 245 Destination Unreachable Type 3, 78-82 DHCP (Dynamic Host Configuration Protocol), 89, 110-122 dial-on-demand routing (DDR), 28 Diffusing Update Algorithm (DUAL), 184 directly connected interfaces, 126 discover messages, 112 Distance-vector routing protocols datagrams, 146 IGRP (Interior Gateway Routing Protocol), 129-131, 181-184 OSPF (Open Shortest Path First), comparing, 153 DIX (Ethernet_II) (Ethernet frame type), 17 DLC (Data Link Control) headers, Ethernet value, 63 DNS (Domain Name System), 252, 301-312 DoD (Department of Defense) Model layers, 5-6
INDEX
487
TCP/IP, 3 Host-to-Host layer, 203, 211, 241 Process/Application layer, 249 Telnet, 258 TCP (Transmission Control Protocol), 211 Domain Name System (DNS), 252, 301-312 domain servers, message formats, 306-310 domains, 348, 252, 302-303 DTP (data transfer process), clients or servers, 271 DUAL (Diffusing Update Algorithm), 184 dumb terminals, 257 duplexes, full-duplex or halfduplex communication modes, 10 dynamic allocation of configuration information, 111 Dynamic Host Configuration Protocol (DHCP), 89, 110-122 dynamic NATs (network address translations), 57-58 dynamic routes, 128
E
E bit (OSPF options field), 177 e-mail, 252, 287-294 early token release, 25 EBCDIC file types, FTP (File Transfer Protocol), 276 echo replies, 74 Echo Reply Type 0, 77-78 Echo Request Type 8, 77-78 echo requests, 74 EDU domain, 302 EGP (Exterior Gateway Protocols), 128, 137, 188-189
EIGRP (Enhanced Interior Gateway Routing Protocol), 128, 133, 184-187 empty line (CRLF), 330 encapsulation protocols, WAN (Wide Area Network) technologies, 29-30 Enhanced Interior Gateway Routing Protocol (EIGRP), 128, 133, 184187 enterprise (trap PDU field), 351 entity headers, 329-330 error codes field, 194 response messages, 330 values, 339 error index (PDU field), 350 error messages, 79-82, 332-333 error packets, 339 error status (PDU field), 350 error subcode field, 194 ETag entity headers, 330 Ethernet AlohaNet, 14 channel access methods, 16-17 collisions, 17 Data Link architecture, 14-22 Fast and Slow Ethernet, comparing, 21 Fast Ethernet, 21-22 Frame Type Quick Reference, 21 frames, 17-21 Gigabit Ethernet, 22 hardware failure, 17 IEEE 802.3 specification, 14-16 name mapping, 17 propagation delay, 17 Slow Ethernet, 21
SNAP, IEEEs 802.3 SNAP frame, 20 values, DLC (Data Link Control) headers, 63 versions, 14-15 Ethernet_802.2, IEEEs 802.3 frames, 20 Ethernet_802.3 (Novell proprietary) (Ethernet frame type), 17 Ethernet_802.3 frames, 20 Ethernet_II (DIX) (Ethernet frame type), 17 Ethernet_II frames, 19 Exchange state (routers), 165-166 Expires entity headers, 330 EXPN command, 293 Exstart state (routers), 164-165 extensions, TFTP (Trivial File Transfer Protocol), 342 Exterior Gateway Protocols (EGP), 128, 137, 188-189 external advertisements, 159-160 eXternal Data Representation (XDR) protocol, 10, 353, 359-360 external peer routers, 189
F
failures, hardware, 17 Fast Ethernet, 21-22 FCS (frame check sequence) algorithm, 9, 13 FDDI (Fiber Distributed Data Interface), 25 feasible successor routes, 185-186 fields ACK packets, 338 address family identifier, RIPv1 headers, 143 advertising router, 161, 180 agent address (trap PDU), 351 area ID, 174
488
TCP/IP PRIMER PLUS
authentication, 175 backup designated router, 178 BGP (Border Gateway Protocols), 191-194 BGP identifier, 192 cache-control, 327 checksum, 174 command, RIPv1 headers, 142-143 connection, 327 data, 194 data packets, 338 Database Description packets, 178-179 date, 327 dead interval, 177-178 designated router, 178 enterprise (trap PDU), 351 error code, 194 error index (PDU), 350 error packets, 339 error status (PDU), 350 error subcode, 194 generic trap ID (trap PDU), 351 headers, SMTP (Simple Mail Transfer Protocol), 291 hello interval, 177 Hello packets, 175-178 hold time, 192 IP address, RIPv1 headers, 144 length, 162, 191, 245 Link State Request packets, 161, 179-180 Link State Update packets, 180 LS age, 161 LS checksum, 162 LS sequence number, 162 LS type, 161
LSA (link state advertisement) header, 179 marker, 191 metric, RIPv1 headers, 144 my autonomous system, 192 neighbor, 178 network layer reachability information, 193 network mask, 176 Notification messages, 193-194 number of advertisements, 180 OACK packet, 343 object ID and value, 350-351 open messages, 191-192 Open Messages, 192 optional parameters, 192 options, 161, 177-179 OSPF (Open Shortest Path First), 173-175 packet length, 174 packet type, 173-174 parameter, bits, 308-309 path attributes, 193 PDUs (Protocol Data Units), 350-351 pragma, 327 request ID (PDU), 350 router ID, 174 router priority, 177 RRQ packets, 337-338 sequence number, 179 specific trap ID (trap PDU), 351 time stamp (trap PDU), 351 total length, IP headers, 67 total path attribute length, 193 trailer, 327 transfer-encoding, 327-328 type, 191
unfeasible routes length, 193 unused, RIPv1 headers, 143 Update messages, 192-193 upgrade, 328 version, 143, 192 version number, 174 via, 328 warning, 328 withdrawn routes, 193 WRQ packets, 337-338 File Transfer Protocol (FTP), 243, 253, 269-280, 335 TFTP (Trivial File Transfer Protocol), 243, 253, 335-343 files accessing by NFS clients, 358 boot file names, 109, 122 EBCDIC file types, 276 FTP structure, 277 image file types, 276 local file types, 276 requests, redirectors, 5 RRQ (request to read), 336 transfer protocols, 335 transferring, 253 WRQ (request to write), 336 filesystems, mount command, 356 filtering, ICMP message errors, 82 FIN (finish) control flag, 217, 227-229 flags AA (authoritative answer), 307 ACK (acknowledgement) control, 216, 224-229 domain server message format, 307 FIN (finish) control, 217, 227-229 IP headers, 67-68 PSH (push) control, 216
INDEX
489
RA (recursion available), 307 RD (recursion desired), 307 RST (reset) control, 217 6 bits, control, 216-217 SYN (synchronization) control, 217, 224-230 TC (truncation), 307 2 bytes, DHCP (Dynamic Host Configuration Protocol) protocol headers, 121 URG (urgent) control, 216 Zero, 307 flow control, 206, 221, 234-237 Flush timers, 183 Ford-Fulkerson (Bellman-Ford algorithm), 138 formats control, FTP data types, 276 Fortran carriage control, 276 ICMP (Internet Control Message Protocol) headers, 75-76 messages, 306-310, 325-330 nonprint (default) format control, 276 response messages, 330 SMTP (Simple Mail Transfer Protocol), 291-292 SNMP messages, 348-351 Telnet format control, 276 Fortran carriage control, 276 forwarding databases (OSPF), 155 fragment offset, IP headers, 68-71 fragmentation, ICMP message errors, 80-81 frame check sequence (FCS) algorithm, 9 Frame Relay protocol, 29 Frame Type Quick Reference, 21 frames Ethernet, 17-21 IEEEs 802.3, 20 Token-Ring, 24
frameworks, conceptual, 4 framing packets, 12 From request headers, 329 FTP (File Transfer Protocol), 243, 253, 269-280, 335 TFTP (Trivial File Transfer Protocol), 243, 253, 335343 Full state (routers), 166 full-duplex communication mode, 10 full-mesh topology, 189 functions method tokens, 326 OSI Reference Model layers, 3, 6
generic trap ID (trap PDU field), 351 GET method tokens, 326 Gigabit Ethernet, Data Link architecture, 22 GOV domain, 302 governing groups, Internet technology, 31 Graphic User Interface (GUI), 323 graphic, defined, 323 groups, governing Internet technology, 31 GUI (Graphic User Interface), 323
H
half-duplex communication mode, Session layer (OSI Reference Model), 10 handshakes, three-way, 225-227 hardware addresses, 91 ARP (Address Resolution Protocol) headers, 98 clients, 108, 122 RARP (Reverse Address Resolution Protocol) headers, 103 failure, 17 Htype (hardware type), 107 Htype (hardware type 1 byte), 120 senders hardware addresses, 99, 104 target hardware addresses, 99, 104 types ARP (Address Resolution Protocol) headers, 97 RARP (Reverse Address Resolution Protocol) headers, 103
G
gateways, 41, 139-140 checksum, 76 codes, 75-76, 84-86 default, 127 EGP (Exterior Gateway Protocols), 128 EIGRP (Enhanced Interior Gateway Routing Protocol), 133 HTTP (Hypertext Transfer Protocol), 323 ICMP (Internet Control Message Protocol), 73-82 IGP (Interior Gateway Protocols), 128 IP addresses, 108, 121 OSPF (Open Shortest Path First), 176 split horizon rule, 130 static routes, 126 general headers, 327-328 generic domains, 302 generic start lines, HTTP message formats, 326
490
TCP/IP PRIMER PLUS
Harslem, Eric, 270 Harvey, Brian (Leaving Well Enough Alone), 270 HDLC (High-Level Data Link Control), 29-30 HEAD method tokens, 326 headers answer, domain server message format, 309 ARP (Address Resolution Protocol), 96-99 BGP (Border Gateway Protocols), 191-194 BOOTP (Boot Parameter) protocol, 105-109 DHCP (Dynamic Host Configuration Protocol) protocol, 106, 119-122 empty line (CRLF), 330 entity, 329-330 fields, SMTP (Simple Mail Transfer Protocol), 291 general, 326-328 HTTP message formats, 328-330 ICMP (Internet Control Message Protocol) formats, 75-76 IP (Internet Protocol), 62-73, 220 LSAs (link state advertisements), 160-162 OSPF (Open Shortest Path First), 175-180 pseudo, 218 pseudo IP, 246 question, domain server message format, 309-310 RARP (Reverse Address Resolution Protocol), 103-104 removing, 9 request, 328-329 response, 329
RIPv1, 142-144 TCP (Transmission Control Protocol), 212-218, 235 UDP (User Datagram Protocol), 244-247 Heafner, John, 270 hello interval field, 177 Hello messages, adjacency databases, 164 hello packet type, 174 Hello packets, 175-178 Hello/ACKs packets, 187 HELO command, 293 help, Frame Type Quick Reference, 21 HELP command, 293 HELP [string] command, 280 HEMS (High-level Entity Management), 345 HFTP access control commands, 278-279 high-layer, ARP cache mechanism, 94 High-Level Data Link Control (HDLC), 29-30 High-level Entity Management (HEMS), 345 HINFO (RR type), 310 history, FTP (File Transfer Protocol), 270 Hlen (hardware length), 107 Hlen (hardware length 1 byte), 120 hold down, 130-131 hold time field, 192 Holddown timers, 183 hops BOOTP (Boot Parameter) protocol headers, 107 counts, maximum, 130-131 number of, 141 1 byte, 120
horizons, split horizon rule, 130 Host A and Host B, sending and receiving datagrams, 43 Host request headers, 329 Host-to-Host (DoD model), 203, 211, 241 hosts acknowledgements, 233 ARP (Address Resolution Protocol), 92-94 bits, 45-46, 52 choke packets, 236 default routes, 127 dynamic routes, 128 flow control, 206, 236 headers and trailers, removing, 9 ICMP (Internet Control Message Protocol), 73-86 keepalives, 206 multiplexing, 219 ranges, calculating, 48-51 remote, 5, 257 routing, 125 server host names, 108, 122 sliding window control mechanisms, 206 static routes, 126-127 subnets, 42-43 window sizes, 235 HTTP (Hypertext Transfer Protocol), 251-252, 321-332 Htype (hardware type), 107 Htype (hardware type 1 byte), 120 hybrid protocols, 133, 184, 199 hyper (prefix), 252 hyper, definition, 321 Hypertext Transfer Protocol (HTTP), 251-252, 321-332
INDEX
491
I-J
I (Init) or (More) Database Description packet option, 179 IAB (Internet Activities Board), 345 IAB (Internet Architecture Board), 31 ICMP (Internet Control Message Protocol), 73-86 ID (identifier), domain server message format, 306 identification, IP headers, 67 identifiers address family identifier field, 143 checksum, 76 IDs 1 ID value (LSAs), 161 2 ID value (LSAs), 161 3 ID value (LSAs), 161 4 ID value (LSAs), 161 5 ID value (LSAs), 161 area ID field, 174 generic trap ID (trap PDU field), 351 link state ID field, 161, 180 numbers, 312 object ID and value, 350-351 request ID (PDU field), 350 router ID field, 174 specific trap ID (trap PDU field), 351 transactions, 107, 120, 362 IEEE 802.3 specification, 14-21, 24 IEEE 802.5 specification, 22-24 IETF (Internet Engineering Task Force), 31, 153 If-Modified-Since request headers, 329 If-None-Match request headers, 329 If-Range request headers, 329
If-Unmodified-Since request headers, 329 IGPs (Interior Gateway Protocols), 128, 137, 188-189 IGRP (Interior Gateway Routing Protocol), 128-129, 181-184 image file types, FTP (File Transfer Protocol), 276 implied acknowledgements, 214 inform messages, 112 Information Reply Type 16, 86 Information Request Type 15, 86 Init state (routers), 162-163 instances, 347 Integrated Services Digital Network (ISDN), 29 inter-area advertisements, 158-159 interfaces APIs (Application Programming Interfaces), 314 directly connected, 126 FDDI (Fiber Distributed Data Interface), 25 GUI (Graphic User Interface), 323 user, FTP (File Transfer Protocol), 270 Interior Gateway Protocols (IGPs), 128, 137, 188-189 Interior Gateway Routing Protocol (IGRP), 128-129, 181-184 internal peer routers, 189 internal routers, 167 International Organization for Standardization (ISO), 345-346 International Telecommunications Union, X.400 naming model (SMTP), 291 Internet ARIN (American Registry for Internet Numbers), 35 domain names, 304-305
IAB (Internet Activities Board), 345 intranets, comparing, 31 routing tables, Web sites, 188 technology, governing groups, 31 Internet Activities Board (IAB), 345 Internet Architecture Board (IAB), 31 Internet Control Message Protocol (ICMP), 73-86 Internet Engineering Task Force (IETF), 31, 153 Internet Protocol. See IP Internet Research Task Force (IRTF), 31 Internet Service Providers (ISPs), 53 Internet Society (ISOC), 31 interpreters, FTP (File Transfer Protocol), 270-271 intra-area advertisements, 157-158 intranets and Internet, comparing, 31 Invalid timers, 183 inverse mappings or queries, IP addresses, 305 IP (Internet Protocol), 61, 138 address resolution, 89 addresses, 108, 121, 144, 305 addressing, 35-45, 53-58 best paths, 129 default routes, 127 directly connected interfaces, 126 distance-vector routing protocols, 129-131 DLC (Data Link Control) headers, Ethernet value, 63 dynamic routes, 128 EIGRP (Enhanced Interior Gateway Routing Protocol), 133 headers, 62-73, 220, 242, 246
492
TCP/IP PRIMER PLUS
hybrid routing protocols, 133 link state routing protocols, 132 RFC 791, 62 routing protocols, 129-133 static routes, 126-127 total length field, 64, 67, 71-73 IRTF (Internet Research Task Force), 31 ISDN (Integrated Services Digital Network), 29 ISO (International Organization for Standardization), 345-346 ISOC (Internet Society), 31 ISPs (Internet Service Providers), 53
K
Kahn, Robert, TCP (Transmission Control Protocol), 211 Keepalive messages, 194 keepalives, 206, 234 kernels (Unix), mount command, 356 keyboards, Telnet, 257 keystrokes, Telnet, 259
L
LANs (Local Area Networks), 168, 353-354 LAPB (Link Access Procedure, Balanced) (X.25) protocol, 30 Last-Modified entity headers, 330 late collisions, 17 layer 2 addresses, 13 layers Application (OSI Reference model), 9-10, 251-253
Data Link (OSI Reference Model), 12-13 DoD (Department of Defense) Model, 5-6 high-layer, ARP cache mechanism, 94 Host-to-Host (DoD model), 203, 211, 241 Link, ARP cache mechanism, 94 Network (OSI Reference Model) ARP (Address Resolution Protocol), 89-99 BOOTP (Bootstrap Protocol), 89 DHCP (Dynamic Host Configuration Protocol), 89 ICMP (Internet Control Message Protocol), 73-86 IP addressing, 35-53 IP (Internet Protocol), headers, 61-73 node addresses, 35 protocols, 12 RARP (Reverse Address Resolution Protocol), 89, 99-104 reachability information field, 193 RIP (Routing Information Protocol), 138 TCP (Transmission Control Protocol), 211 OSI Reference Model, 3-13, 249 Physical (OSI Reference Model), 13 Presentation (OSI Reference Model), 10, 253
Process/Application (DoD model), 249 Session (OSI Reference Model), 10-11 Transport (OSI Reference Model), 11-12 BOOTP (Boot Parameter) protocol, 104-105 DHCP (Dynamic Host Configuration Protocol), 110-122 hosts, 206 OSI Reference model, 203 ports, 207-209 protocols, 203-204 sockets, 207-209 TCP (Transmission Control Protocol), 203-207 UDP (User Datagram Protocol), 105-109, 203, 241 ULPs (upper layer protocols), 249, 251 lease duration, DHCP message exchanges, 119 leased (dedicated) lines, 26-27 Leaving Well Enough Alone, 270 length field, 162, 191, 245 lengths Hlen (hardware length), 107 Hlen (hardware length 1 byte), 120 IP headers, 64, 67 line mode, 258 linefeed character text, 260 lines, 325-326, 330 Link layer, ARP cache mechanism, 94 link state acknowledgement packet type, 174
INDEX
493
Link State Acknowledgement packets, 180-181 link state advertisements. See LSAs Link State Algorithm (LSA), 152 link state databases (OSPF), 155 link state ID field, 161, 180 link state request packet type, 174 Link State Request packets, 179-180 link state routing protocols, 132 link state type field, 179 link state update packet type, 174 Link State Update packets, 180 links, virtual, 172-173 LIST [pathname] command, 280 load balancing, 155 Load metric, 182 Loading state (routers), 166 loads, IGRP networks, balancing and sharing, 184 local file types, FTP (File Transfer Protocol), 276 logical addressing, 12 logical circuits, 219 logical protocol addresses, 100-101 low-level addresses, 299 LS age field, 161 LS checksum field, 162 LS sequence number field, 162 LS type field, 161 LSA (Link State Algorithm), 152 LSAs (link state advertisements), 156 1 ID value, 161 1 link state type, 157-158 2 ID value, 161 2 link state type, 157-158 3 ID value, 161 3 link state type, 157-159 4 ID value, 161 4 link state type, 157-159
5 ID value, 161 5 link state type, 157-160 7 link state type, 157-160 areas, 170-173 external advertisements, 159-160 headers, 160-162 inter-area advertisements, 158-159 intra-area advertisements, 157-158 link state advertisement field, 179-180 low-level addresses, 299
M
MAC (Media Access Control), 12 MAC address, low-level addresses, 299 MAIL FROM command, 293 Management Information Bases (MIBs), 346 managers, SNMP (Simple Network Management Protocol), 347 manual allocation of configuration information (DHCP), 111 mapping IP addresses, 305 name resolution, 305 names, Ethernet, 17 NFS (Network File System), 357 private addresses, 57 TCP (Transmission Control Protocol), 203 UDP (User Datagram Protocol), 203, 241 marker field, 191 masks subnet, 46-48 VLSMs (variable length subnet masks), 44
Max-Forwards request headers, 329 maximum hop count, 130-131 McKenzie, Alex, 270 media (suffix), 252 Media Access Control (MAC), 12 message body (untransparent), 330 message formats domain servers, 306-310 empty line (CRLF), 330 entity headers, 329-330 general headers, 326-328 generic start lines, 326 headers, 328 HTTP (Hypertext Transfer Protocol), 325 message body (untransparent), 330 request headers, 328-329 response headers, 329 RIPv1, headers, 142-144 Message Transfer System (MTS), 290 messages ACK (acknowledgement), 112 call, 361-365 catchall, 85 chunking, 327 command, RIP (Routing Information Protocol), 142 decline, 112 DHCP (Dynamic Host Configuration Protocol), 111-112 discover, 112 error, 332-333 exchanging, 112-119 ICMP (Internet Control Message Protocol) 0 (network unreachable), 79
494
TCP/IP PRIMER PLUS
1 (host unreachable), 79 2 (protocol unreachable), 79 3 (port unreachable), 79 4 (fragmentation needed), 80-81 5 (source route failed), 81 6 (destination network unknown), 81 7 (destination host unknown), 81 8 (source host isolated), 81 9 (destination network administratively prohibited), 81 10 (destination host administratively prohibited), 82 11 (network unreachable for ToS), 82 12 (host unreachable for ToS), 82 13 (communication administratively prohibited by filtering), 82 14 (host precedence violation), 82 15 (precedence cutoff in effect), 82 formats, 75-76 types, 77-86 inform, 112 Keepalive messages, 194 keepalives, 206 NAK, 112 Notification messages fields, 193-194 offer, 112 Open Messages fields, 191-192
release, 112 reply, stats lines, 325 request, 112, 325 response, 330-332 route pairs, 144 SNMP formats, 348-351 trap, 347 Update messages fields, 192-193 method tokens, 323, 326 metric field, RIPv1 headers, 144 methods, channel access, 16-17, 24-25 metrics, 181-182 MIBs (Management Information Bases), 346-347 MIL domain, 302 MINFO (RR type), 310 MKD [pathname] command, 280 models. See also DoD (Department of Defense) Model; OSI Reference Model core-distribution-access, static routes, 126 X.400 naming model (SMTP), 289-290 modes block transmission, 278 character, 258 compressed transmission, 278 line, 258 reception in XDR (External Data Representation), 360 stream transmission, 278 transmission, 258, 274-275, 278 MODE [mode] command, 279 mound command, 356 mount server procedures, RPC call messages, 365 MS (Master/Slave) (Database Description packet option), 179
MTAs (message transfer agents), 291 MTS (Message Transfer System), 290 multipath routing, 183 multiple area implementation, 169-170 Multiplexer/Demultiplexer (MUX/DEMUX), 28 multiplexing hosts, 219 MUX/DEMUX (Multiplexer/Demultiplexer), 28 MX (RR type), 310 my autonomous system field, 192
N
NAK messages, 112 name mapping, Ethernet, 17 name resolution, 299 DNS (Domain Naming System), 301-312 IP addresses, resolving, 305 namespace, 300-301 NetBEUI (NetBIOS Basic Extended User Interface), 313 NetBIOS (Network Basic Input Output System), 313-315 NIC (Network Information Center), 300 name servers, 302-304 names boot files, 109, 122 community, SNMP message formats, 349 DNS (domain name system), 252 domains, 304-305 server hosts, 108, 122
INDEX
495
URN (Uniform Resource Name), 324 X.400 naming model (SMTP), 289-290 namespace, 300-301 NAT (network address translation), 55-58 NBMA (nonbroadcast multiaccess) networks, 168-169 negotiations, capability, 322 neighbor field, 178 neighbor routers, 189 Neigus, Nancy, 270 NET domain, 302 NetBEUI (NetBIOS Basic Extended User Interface), 313-314 NetBIOS (Network Basic Input Output System), 11, 313-315 network address translation (NAT), 55-58 Network Basic Input Output System (NetBIOS), 11, 313-315 Network File System. See NFS Network Information Center (NIC), 300 Network layer (OSI Reference Model) ARP (Address Resolution Protocol), 89-99 BOOTP (Bootstrap Protocol), 89 DHCP (Dynamic Host Configuration Protocol), 89 ICMP (Internet Control Message Protocol), 73-86 IP addressing, 35-53 IP (Internet Protocol), headers, 61-73 node addresses, 35 protocols, 12 RARP (Reverse Address Resolution Protocol), 89, 99-104
reachability information field, 193 RIP (Routing Information Protocol), 138 TCP (Transmission Control Protocol), 211 network mask field, 176 network virtual terminal (NVT), 252, 259-260 networking complexity, OSI Reference Model layers, reducing, 7 networks. See also Telnet areas, 170-173 AS (autonomous systems), 138 breaking up, 44 broadcast-based LAN, 168 Class B, 44, 49-51 default routes, 127 dynamic routes, 128 echo replies, 74 echo requests, 74 ICMP message errors, 79-82 IGRP (Interior Gateway Routing Protocol), 182-184 multiple area implementation, 169-170 NAT (network address translation), 55-58 NBMA (nonbroadcast multiaccess), 168-169 point-to-point connections, 168 SNMP (Simple Network Management Protocol), 345-351 static routes, 126-127 subnet masks, 40-43 subnetting, 44-55 traffic, routing or shouting, 40 WAN (Wide Area Network) technologies, 25-30
NFS (Network File System), 10 cd command, 359 clients, 357-358 features, 354 mapping, 357 multi-vendor products, 355-356 operation, 356 RPC (Remote Procedure Calls), 353 server procedures, RPC call messages, 364-365 servers, 358-359 users, autofs (auto file system), 359 version 2 or version 3 features, 354-355 XDR (External Data Representation), 353 NIC (Network Information Center), 300 NLST [pathname] command, 280 node addresses, 35 non-transparent proxy agents, 323 nonbroadcast multiaccess (NBMA), 168-169 nonprint (default) format control, 276 NOOP command, 280, 293 not authoritative name servers, 304 not so stubby areas (NSSAs), 159, 171-172 Notification messages fields, 193-194 NS (RR type), 310 NSCOUNT, domain server message format, 309 NSSAs (not so stubby areas), 159, 171-172 number of advertisements field, 180 numbering systems, binary or decimal, 33
496
TCP/IP PRIMER PLUS
numbers acknowledgement, 214-215 ARIN (American Registry for Internet Numbers), 35 binary, converting to decimal numbers, 33-34 checksum sequence, 76 IDs, 312 LS sequence number field, 162 sequence, 214 sequence number field, 179 TCP (Transmission Control Protocol) ports, 237-238 TCP and UDP ports, 431 three-digit number code, SMTP e-mail replies, 293-294 version number field, 174 numeric code, three-digit (FTP), 281 NVT (Network Virtual Terminal), 252, 259-260
O
OACK (option acknowledgement) packet, 342-343 object ID and value, 350-351 objectives, FTP (File Transfer Protocol), 269 objects, instances, 347 octets, TCP (Transmission Control Protocol), 232 offer messages, 112 offsets data, 215 fragment, IP headers, 68-71 on position, binary numbers, converting to decimal numbers, 34 ONC (Open Network Computing), 353-354
Op (operation code), 107 Op (operation code 1 byte), 119 Opcode (operation code), 99, 103, 306 Open Messages fields, 191-192 Open Network Computing (ONC), 353-354 Open Shortest Path First. See OSPF operating systems, company developed, 3 operation code (Op), 107 operation code 1 byte (Op), 119 operation code. See OP; Opcode operations ARP (Address Resolution Protocol), 91-94 BGP (Border Gateway Protocols), 190-191 EIGRP (Enhanced Interior Gateway Routing Protocol), 184-186 NFS (Network File System), 356-359 OSPF (Open Shortest Path First), 156-162 Proxy ARP (Address Resolution Protocol), 95-96 RARP (Reverse Address Resolution Protocol), 100-101 logical protocol addresses, 100-102 TCP (Transmission Control Protocol), 218-222 TFTP (Trivial File Transfer Protocol), 340 UDP (User Datagram Protocol), 242-244 option acknowledgement (OACK) packets, 342 optional nontransitive attribute (4Multi-Exit-Disc type code), 196-197
optional nontransitive category (path attributes), 195-196 optional parameters field, 192 optional parameters length field, 192 optional transitive attribute (7Aggregator type code), 197 optional transitive category (path attributes), 195-197 options field, 161, 177-179 IP headers, 73 variable lengths, 122, 217-218 OPTIONS method tokens, 326 ORG domain, 302 origin servers, HTTP (Hypertext Transfer Protocol), 323 OSI Reference Model Application layer, 9-10, 251-253 conceptual frameworks, 4 Data Link layer, 12-13 ISO (International Organization for Standardization), 346 layers, 3-13, 249 mapping to WAN protocols, 26 Network layer ARP (Address Resolution Protocol), 89-99 BOOTP (Bootstrap Protocol), 89 DHCP (Dynamic Host Configuration Protocol), 89 ICMP (Internet Control Message Protocol), 73-86 IP addressing, 35-53 IP (Internet Protocol), headers, 61-73
INDEX
497
node addresses, 35 protocols, 12 RARP (Reverse Address Resolution Protocol), 89, 99-104 reachability information field, 193 RIP (Routing Information Protocol), 138 TCP (Transmission Control Protocol), 211 Physical layer, 13 Presentation layer, 10, 253 protocols, 4 redirectors, 5 remote hosts, 5 Session layer, 10-11 TCP (Transmission Control Protocol), 211 Telnet, 258 Transport layer, 11-12 BOOTP (Boot Parameter) protocol, 104-105 DHCP (Dynamic Host Configuration Protocol), 110-122 hosts, 206 OSI Reference model, 203 ports, 207-209 protocols, 203-204 sockets, 207-209 TCP (Transmission Control Protocol), 203-207 UDP (User Datagram Protocol), 105-109, 203, 241 when to use, 5
OSPF (Open Shortest Path First), 128, 132 ABR routers, 167 area ID field, 174 areas, 170-173 ASBR routers, 167 authentication field, 175 backbone routers, 167 broadcast-based LAN networks, 168 characteristics, 154-155 checksum field, 174 data link architectures, 167 database description packet type, 174 Database Description packets, 178-179 databases, 155 and Distance-vector routing protocols, comparing, 153 external advertisements, 159-160 fields, 173-175 gateways, 176 headers, 175 Hello messages, adjacency databases, 164 hello packet type, 174 Hello packets, 175-178 inter-area advertisements, 158-159 internal routers, 167 intra-area advertisements, 157-158 link state acknowledgement packet type, 174 Link State Acknowledgement packets, 180-181 link state request packet type, 174 Link State Request packets, 179-180
link state update packet type, 174 Link State Update packets, fields, 180 load balancing, 155 LSA (Link State Algorithm), 152 LSAs (link state advertisements), 156, 160-162 multiple area implementation, 169-170 NBMA (nonbroadcast multiaccess) networks, 168-169 operation, 156-157 options field, E bit or T bit, 177 packet length field, 174 packet type field, 173-174 point-to-point connections, 168 router ID field, 174 router states, 162-166 router types, 167 version 1, 153 version 2, 153 version number field, 174
P
packet length field, 174 packet type field, 173-174 packet-switched connections, 26-28 packets 9 (request) packet, 150 10 (response) packet, 150 11 (acknowledgement) packet, 150 ACK (acknowledgement), 338 choke, 236 data, 338
498
TCP/IP PRIMER PLUS
Database Description, 178-179 database description type, 174 delivering, 221-222 demand circuit, 150 error, 339 framing, 12 Hello, 175-178 hello type, 174 Hello/ACKs, 187 Link State Acknowledgement, 180-181 link state acknowledgement type, 174 Link State Request, fields, 179-180 link state request type, 174 Link State Update, fields, 180 link state update type, 174 OACK (option acknowledgement), 343 queries, 187 replies, 187 requests, 187 RRQ (request to read), 337-338 switching, 12 TFTP (Trivial File Transfer Protocol), 336-338 types, 149-150, 187 updates, 187 WRQ, 337-338 padding IP headers, 73 pages, FTP structure, 277 pairing sockets, 11, 219, 224-227 parameter field, bits, 308-309 Parameter Problem Type 12, 85 parameters, FTP (File Transfer Protocol), 274 partial-mesh topology, 189 partitions (domains), zones, 303
PASS [password] command, 278 PASV command, 279 path attributes BGP (Border Gateway Protocol), 191, 194-198 field, 193 optional nontransitive attribute, 196-197 optional transitive attribute, 197 well-known discretionary attribute, 196-198 well-known mandatory attribute, 195-196 paths hops, number of, 141 multipath routing, 183 selecting, 140-141 PDUs (Protocol Data Units), 348-351 peer routers, 189-190 Physical layer (OSI Reference Model), 13 Ping, 85 echo replies or requests, 74 Echo Reply Type 0, 77-78 point-to-point leased lines, 26 point-to-point connections, 168 Point-to-Point Protocol (PPP), 30 poison reverse, 130, 146 polls, unicast, ARP cache mechanism, 94 port 23 (Telnet), 257 ports, 11 destination, 213, 245 ICMP message error, 3 (port unreachable), 79 NetBIOS TCP/IP, 315 source, 213, 245
TCP (Transmission Control Protocol) FTP (File Transfer Protocol), 271 numbers, 237-238 and UDP, numbers, 431 Telnet, 208 Transport layer, 207-209 UDP (User Datagram Protocol), 244, 311-312 PORT [host-port] command, 279 POST method tokens, 326 Postel, Joh, 270 PPP (Point-to-Point Protocol), 30 pragma field, 327 precedence bits (bits 02), 64-65 ICMP message errors, 15 (precedence cutoff in effect), 82 security, 222-223 prefixes, hyper, 252 Presentation layer (OSI Reference Model), 10, 253 print services, requests, redirectors, 5 private addresses, mapping, 57 procedures, servers, RPC call messages, 364-365 Process/Application (DoD model), 249 products (NFS), multi-vendors, 355-356 program (RPC call messages), registered, 362-364 propagation delay, 17 Protocol Data Units (PDUs), 348-351 protocols. See also ARP; BGP; IP;
INDEX
499
NFS; OSI; OSPF; TCP; Telnet; UDP ATM (Asynchronous Transfer Mode), 30 balanced hybrid protocols, 184 comparing header fields, 191 IGPs (Interior Gateway Protocols) and EGPs (Exterior Gateway Protocols), comparing, 188-189 Keepalive messages, 194 length field, 191 marker field, 191 Notification messages fields, 193-194 open messages fields, 191-192 Open Messages fields, 192 operation, 190-191 path attributes, 194-198 routers, 189-190 type field, 191 Update messages fields, 192-193 BOOTP (Bootstrap Protocol), 89, 104-109 class routing, 132 classful routing, 132, 147 client PI (protocol interpreter), 270-271 CMIP (Common Management Information Protocol), 345 connection-oriented, 204-207, 223-237 connectionless, 206-207 DHCP (Dynamic Host Configuration Protocol), 89, 110-122
distance-vector, 129-131, 184 Distance-vector routing protocols, 146, 153 EGPs (Exterior Gateway Protocols), 128, 137 EIGRP (Enhanced Interior Gateway Routing Protocol), 128, 133, 184-186 encapsulation, WAN (Wide Area Network) technologies, 29-30 Frame Relay protocol, 29 FTP (File Transfer Protocol), 243, 269-272, 335 HDLC (High-Level Data Link Control), 29-30 HEMS (High-level Entity Management), 345 Host-to-Host layer, protocols, 203 HTTP (Hypertext Transfer Protocol), 251-252 321-332 hybrid, 133, 199 IAB (Internet Activities Board), 345 ICMP (Internet Control Message Protocol), 73-86 IGPs (Interior Gateway Protocols), 128, 137 IGRP (Interior Gateway Routing Protocol), 181-184 ISDN (Integrated Services Digital Network), 29 ISO (International Organization for Standardization), 346 link state routing, 132 Network layer (OSI Reference Model), 12 PDUs (Protocol Data Units), 348-351 PPP (Point-to-Point Protocol), 30
Presentation layer (OSI Reference model), 253 RARP (Reverse Address Resolution Protocol), 89, 99-104 RIP (Routing Information Protocol), 128, 138 RIPv1, 128 RIPv2, 128 routing, 129-133, 137 RPC (Remote Procedure Calls), 353 SDLC (Synchronous Data Link Control), 29 senders protocol addresses, 99, 104 server PI (protocol interpreter), 271 single-routing-protocols, 184 SLIP (Serial Line Internet Protocol), 30 SMTP (Simple Mail Transfer Protocol), 252, 287-294 SNMP (Simple Network Management Protocol), 345-351 SubNetwork Access Protocol (IEEE 802.3) (Ethernet frame type), 17 target protocol addresses, 99, 104 TFTP (Trivial File Transfer Protocol), 243, 253, 335-343 Transport layer, 203-209 ULPs (upperlayer protocols), 249-251 WAN (Wide Area Network), mapping OSI Reference Model, 26 X.25 LAPB (Link Access Procedure, Balanced) protocol, 30 XDR (eXternal Data Representation), 10, 353
500
TCP/IP PRIMER PLUS
proxies agents, 323-324 HTTP (Hypertext Transfer Protocol), 323 servers, 322 SNMP (Simple Network Management Protocol), 348 Proxy ARP (Address Resolution Protocol), 95-96 Proxy-Authorization request headers, 329 pseudo headers, 218, 246-247 PSH (push) control flag, 216 PTR (RR type), 310 public domains, 348 push (PSH) control flag, 216 PUT method tokens, 326 PWD command, 280
Q
QDCOUNT, domain server message format, 309 QR (query or response), domain server message format, 306 queries, 305 queries packets, 187 query or response (QR), domain server message format, 306 question headers, domain server message format, 309-310 QUIT command, 279, 293
R
RA (recursion available) flag, 307 rames, Ethernet_802.3, 20 Range request headers, 329 ranges, calculating hosts, 48-51 subnets, 47
RARP (Reverse Address Resolution Protocol), 89, 99-104 Rcode, domain server message format, 307-309 RCPT TO command, 293 RD (recursion desired) flag, 307 records FTP structure, 277 RRs (Resource Records), 309-310 Redirect Type 5, 83 redirectors clients, 251 OSI Reference Model, 5 reference models. See OSI Reference Model references, Frame Type Quick Reference, 21 Referer request headers, 329 registered programs (RPC call messages), 362-364 REIN command, 279 release messages, 112 reliability (guaranteed packet delivery), 221-222 Reliability metric, 182 remote hosts OSI Reference Model, 5 Telnet, 257 Remote Procedure Calls (RPCs), 11, 353, 360-365 removing headers or trailers, 9 repeating, bit repeating, 23 replies BOOTP (Boot Parameter) protocol, 109 echo, 74 FTP (File Transfer Protocol), 281 SMTP (Simple Mail Transfer Protocol), 293-294 replies packets, 187
reply messages, stats lines, 325 Request for Comments (RFCs), 30-31, 35 request ID (PDU field), 350 request to read (RRQ), 336 request to write (WRQ), 336 requests bad request error messages, 332-333 BOOTP (Boot Parameter) protocol, 109 chains, 324 echo, 74 file or print, redirectors, 5 headers, 328-329 HTTP (Hypertext Transfer Protocol), 322 lines (request messages), 325 messages, 112, 325 mounting or unmounting, NFS clients, 357 9 (request) packet, 150 packets, 187 Requests for Comments. See RFCs reserved TCP headers, 216 reserved addresses, 39 reset (RST) control flag, 217 resolution of addresses, 89 resolution of names. See name resolution resolving IP addresses, 305 resource records (RRs), 302, 309-310 resources, HTTP (Hypertext Transfer Protocol), 323 responders, servers, 251 response headers, 329 response messages, 330-332 responses, 10 (response) packet, 150 REST [marker] command, 280 retransmissions, 233
INDEX
501
RETR [pathname] command, 280 returns, carriage, FTP (File Transfer Protocol) commands, 280 Reverse Address Resolution Protocol (RARP), 89, 99-104 Reynolds, Joyce, 270 RFC 791, 62 RFC 821, SMTP (Simple Mail Transfer Protocol), 287 RFC 822, SMTP (Simple Mail Transfer Protocol), 289 RFC 1123, SMTP (Simple Mail Transfer Protocol), 290 RFCs (Requests for Comments), 30 Address Resolution, 374 FTP (File Transfer Protocol), 396-398 HTTP (Hypertext Transfer Protocol), 414-415 Industry Models and Standards, 371 IP Addressing, 371 IP Routing, 375-382 Name Resolution, 410-414 Network Layer/Internet Protocols, 371-374 Open Network Computing Protocols, 421 Routing Protocols, 382-388 SMTP (Simple Mail Transfer Protocol), 398-410 SNMP (Simple Network Management Protocol), 416-421 TCP (Transmission Control Protocol), 389-391 Telnet, 391-396 TFTP (Trivial File Transfer Protocol), 415 Transport/Host-to-Host Layer, 389 UDP (User Data Protocol), 391 Web site, 31
RIP (Routing Information Protocol), 128 1 command, 142 2 command, 143 3 command, 143 4 command, 143 5 command, 143 9 command, 143 10 command, 143 11 command, 143 advertisements, 144 AS (autonomous systems), 138 Bellman-Ford algorithm, 138 classful routing protocols, subnetting, 147 command messages, 142 demand circuits, 148-150 gateways, 139-140 messages, route pairs, 144 Network layer protocol, 138 paths, hops, number of, 141 RIPv1 (version 1), 138-147, 151-152 RIPv2 (version 2), 138, 150-152 routers, 146 timers, 147-148 triggered updates, 149 RIPv1 (distance-vector routing protocol), 128-129 disadvantages, 144-145, 147 headers, 142-144 message formats, headers, 142 path selection, 140-141 RFC 1058, 138 RIPv2, comparing, 151-152 RIPv2 (distance-vector routing protocol), 128-129 RFC 2453, 138 RIPv1, comparing, 151-152
RMD [pathname] command, 280 RNFR [pathname] command, 280 RNTO [pathname] command, 280 route pairs, RIP messages, 144 route summarization, Class C addresses, 53-55 route update traffic control, 148 Router Advertisement Type 9, 84 router ID field, 174 router priority field, 177 Router Solicitation Type 10, 84 routers ABR, 167 advertising router field, 161 areas, 170-173 ASBR, 167 backbone, 167 best paths, 129 BGP (Border Gateway Protocols), 189-190 broadcast-based LAN networks, 168 EIGRP (Enhanced Interior Gateway Routing Protocol), 186 Exchange state, 165-166 Exstart state, 164-165 external advertisements, 159-160 external peer, 189 Full state, 166 ICMP (Internet Control Message Protocol), 73-86 Init state, 162-163 inter-area advertisements, 158-159 internal, 167, 189 intra-area advertisements, 157-158 Loading state, 166 multiple area implementation, 169-170
502
TCP/IP PRIMER PLUS
NBMA (nonbroadcast multiaccess) networks, 168-169 neighbor, 189 OSPF Hello messages, adjacency databases, 164 packet switching, 12 peers, 189-190 point-to-point connections, 168 poison reverse, 146 private addresses, mapping, 57 RIP, 146 routing protocols, 137 speaker, 189 states of, 162-166 Two-Way state, 163 types of, 167 routes best paths, 129 default, 127 directly connected interfaces, 126 dynamic, 128 feasible successor, 185-186 ICMP message errors, 5 (source route failed), 81 static, 126-127 successor, 185-186 routing CIDR (class interdomain routing), 52-55 classfulless, 132 classless, 132 DDR (dial-on-demand), 28 definition, 40 hosts, 125 multipath, 183 purpose, 125 Snapshot, 149
Routing Information Protocol. See RIP routing protocols, 129, 137 classful, subnetting, 147 distance-vector, 129-131 EIGRP (Enhanced Interior Gateway Routing Protocol), 133 hybrid, 133 link state, 132 routing tables, Web sites, 188 RPCs (Remote Procedure Calls), 11, 353, 360-365 RRQ (request to read) packets, 336-338 RRs (resource records), 302, 309-310 RSET command, 293 RST (reset) control flag, 217 rules, split horizon, 130
S
SA (source address field), 24 SAML FROM command, 293 SDLC (Synchronous Data Link Control), 29 seconds, protocol headers, 107, 121 security authentication field, 175 precedence, 222-223 SEND FROM command, 293 senders hardware or protocol addresses, 99, 104 sequence number field, 179 sequence numbers, 76, 214 sequences, connection-oriented protocols, 230-234 Serial Line Internet Protocol (SLIP), 30
servers DHCP (Dynamic Host Configuration Protocol), 112-119 domains, message formats, 306-310 DTP (data transfer process), 271 FTP (File Transfer Protocol) connections, 272 server commands, 279-280 host names, protocol headers, 108, 122 HTTP (Hypertext Transfer Protocol), 322-323 IP addresses, protocol headers, 108, 121 mount procedures, RPC call messages, 365 names authoritative or not authoritative, 304 RRs (resource records), 302 NFS (Network File System), 358-359, 364-365 PI (protocol interpreter), 271 proxy agents, 324 responders, 251 SMTP (Simple Mail Transfer Protocol), 287 Telnet, 257 Session layer (OSI Reference Model), 10-11 sessions connection-oriented protocols223-230 FTP (File Transfer Protocol), 270-272 HTTP (Hypertext Transfer Protocol), 322-325 Telnet, starting, 257
INDEX
503
SGMP (Simple Gateway Management Protocol), SNMP (Simple Network Management Protocol), 345-351 sharing IGRP network loads, 184 shouting, definition, 40 signaling, balanced or unbalanced, 15 Simple Gateway Management Protocol (SGMP), SNMP (Simple Network Management Protocol), 345-351 Simple Mail Transfer Protocol (SMTP), 252, 287-294 Simple Network Management Protocol (SNMP), 345-351 single-routing-protocols, 184 sites, Web RFCs (Request for Comments), 31 routing tables, 188 SITE [string] command, 280 Slash 8 (Class A) addresses, 35-40 Slash 16 (Class B) addresses, 35-40 Slash 24 (Class C) addresses 35-40 sliding window control mechanisms, 206 SLIP (Serial Line Internet Protocol), 30 Slow Ethernet, 21 SMI (Standard Management Information), 346 SMNT [pathname] command, 279 SMTP (Simple Mail Transfer Protocol), 252, 287-294 SNA (Systems Network Architecture), 29 SNAP frames, IEEEs 802.3, 20 Snapshot routing, 149 Sniffer, acknowledgement numbers, 215 SNMP (Simple Network Management Protocol), 345-351
SOA (RR type), 310 sockets pairing, 11, 219, 224-227 Transport layer, 207-209 Solderblum, Olaf (Token-Ring LAN standard), 22 SOML FROM command, 293 source address field (SA), 24 source ports, 213, 245 Source Quench Type 4, 82 spaces, FTP (File Transfer Protocol) commands, 280 speaker routers, 189 specialization (OSI Reference Model layers), promoting, 7 specific trap ID (trap PDU field), 351 specifications ANSI X3T9.5, 25 IEEE 802.3, 14-21, 24 IEEE 802.5, 22-24 Slow Ethernet, 21 split horizon rule, 130 spooling, 252 stability of IGRP networks, 183 standard areas (Area 0), 170-171 Standard Management Information (SMI), 346 standard stub areas, 171 standards 100BaseFX, 22 100BaseT4, 22 100BaseTX, 22 100BaseX, 22 Data Link architecture, 14 states link state routing protocols, 132 of routers, 162-166 static NATs (network address translations), 57
static routes, 126-127 stats lines (reply messages, 325 status codes, response messages, 330-332 status lines (response messages), 330 STAT [pathname] command, 280 STOR [filename] command, 280 STOU command, 280 stream transmission mode, 278 structures FTP (File Transfer Protocol) data, 274-277 Token-Ring, 24 STRU [structure] command, 279 stub areas, 171-172 stubs, NSSAs (not so stubby areas), 159 subnets bits, determining number of, 45-46 broadcast addresses, 52 Class B network, 49-51 host ranges, calculating, 50-51 hosts, 42-43 masks, 40-43, 46-48 ranges, calculating, 47 subnetting Class B networks, 44 classful routing protocols, 147 IP addressing, 44-55 SubNetwork Access Protocol (IEEE 802.3) (Ethernet frame type), 17 successor routes, 185-186 suffixes, media, 252 summarization, 52-55 Sun Microsystems, 353 supernetting, 52-53 switching circuits, 27-28 switching packets, 12, 27-28
504
TCP/IP PRIMER PLUS
SYN (synchronization) control flag, 217, 224-230 Synchronous Data Link Control (SDLC), 29 SYST command, 280 systems autonomous, multiple area implementation, 169-170 operating, company developed, 3 Systems Network Architecture (SNA), 29
Kahn, Robert, 211 logical circuits, 219 multiplexing, 219 Network layer, 211 octets, 232 operation, 218-219 OSI Reference model, 211 ports, 208, 237-238, 271 precedence and security, 222-223 reliability (guaranteed packet delivery), 221-222 SYN (synchronization) control flag, 224-227, 230 TCB (transmission control block), 218 three-way handshakes, 225-227 Transport layer, mapping to, 203 UDP (User Datagram Protocol), 244, 431 variable-length options, 217-218 windowing, stages, 236 zero windows, 236-237 TCP/IP (Transmission Control Protocol/Internet Protocol), 3, 314-315 tearing down connections, 219 technologies Internet, governing groups, 31 WAN (Wide Area Network), 25-30 Telnet (Telecommunications network) Application layer (OSI Reference model), 252 ASCII (American Standard Code for Information Interchange), 260 carriage control text, 260 clients, 257-258
T
T bit (OSPF options field), 177 tables (routing), Web sites, 188 target hardware or protocol addresses, 99, 104 TC (truncation) flag, 307 TCB (transmission control block), 218 TCP (Transmission Control Protocol), 11 ACK (acknowledgement) control flag, 224-229 values, 212-214 Cerf, Vinton, 211 connection-orientated protocol, 205-207, 223-237 connectionless protocols, 206 connections, setting up and tearing down, 219 data transfers, 220-221 FIN (finish) control flag, 227-229 flow control, 221 headers, 212-218, 235 Host-to-Host layer, 203, 211 implied acknowledgements, 214 IP headers, 220
DoD model, 258 dumb terminals, 257 format control, 276 keyboards, 257 keystroke travel, 259 linefeed character text, 260 NVT (Network Virtual Terminal), 252, 259-260 OSI model, 258 port 23, 257 remote hosts, 257 servers, 257 services, 259-260 sessions, starting, 257 TCP ports, 208 terminals dumb, 257 NVT (Network Virtual Terminal), 259-260 text, carriage control ir linefeed character, 260 TFTP (Trivial File Transfer Protocol), 243, 253, 335-343 FTP (File Transfer Protocol), 243, 253, 269-280, 335 three-digit number code, 281, 293-294 three-way handshakes, 225-227 time, Delay Time metric, 181 Time Exceeded Type 11, 84-85 time stamp (trap PDU field), 351 time to live (TTL), IP headers, 71-72 timeout, ARP cache mechanism, 94 timers, 147-148, 183-184, 233-234 Timestamp Reply Type 14, 86 Timestamp Request Type 13, 86 Token-Ring, 22-25 tokens, 25, 323, 326 top-level domains, 302
INDEX
505
topologies, full-mesh or partialmesh, 189 ToS (Type of Service) bits (8 total bits), IP headers, 64 datagrams, 222 FTP (File Transfer Protocol), 272 ICMP message errors, 82 total length field, IP headers, 67 total path attribute length field, 193 Trace method tokens, 326 traceroute utility, 85 traffic, 40, 148 trailer field, 327 trailers, removing, 9 transaction IDs, 107, 120, 362 transfer-encoding field, 327-328 transferring data, 220-221 files, 253 transfers, bidirectional, 322 transmission control block (TCB), 218 Transmission Control Protocol. See TCP transmission modes, 258, 274-278 transmissions, retransmissions, 233 transparent proxy agents, 323 Transport layer (OSI Reference Model), 11-12 BOOTP (Boot Parameter) protocol, 104-105 DHCP (Dynamic Host Configuration Protocol), 110-122 hosts, 206 OSI Reference model, 203 ports, 207-209 protocols, 203-204 sockets, 207-209
TCP (Transmission Control Protocol), 203-207 UDP (User Datagram Protocol), 105-109, 203, 241 trap messages, 347 trap PDUs (Protocol Data Units), 350-351 triggered updates, 149 Trivial File Transfer Protocol (TFTP), 243, 253, 335-343 FTP (File Transfer Protocol), 243, 253, 269-280, 335 TTL (time to live), IP headers, 71-72 tunnels, HTTP (Hypertext Transfer Protocol), 323 TURN command, 293 Two-Way state (routers), 163 TXT (RR type), 310 Type 0 (Echo Reply), 77-78 Type 3 (Destination Unreachable), 78-82 Type 4 (Source Quench), 82 Type 5 (Redirect), 83 Type 8 (Echo Request), 77-78 Type 9 (Router Advertisement), 84 Type 10 (Router Solicitation), 84 Type 11 (Time Exceeded), 84-85 Type 12 (Parameter Problem), 85 Type 13 (Timestamp Request), 86 Type 14 (Timestamp Reply), 86 Type 15 (Information Request), 86 Type 16 (Information Reply), 86 Type 17 (Address Mask Request), 86 Type 18 (Address Mask Reply), 86 type field, 191 Type of Service (ToS), datagrams, 222 types, RPC call messages, 362
types of messages, ICMP (Internet Control Message Protocol), 73-86 TYPE [type] command, 279
U
UAs (user agents), 287-290, 324 HTTP (Hypertext Transfer Protocol), 323 request headers, 329 UDP (User Datagram Protocol), 11, 138 applications, 243 BOOTP (Boot Paramater) protocol, 105 CRC (Cyclic Redundancy Check), 246 headers, 244-247 Host-to-Host layer, 203, 241 IP headers, 242 operations, 242-243 ports, 244, 311-312 pseudo IP headers, 246 TCP (Transmission Control Protocol), 244, 431 Transport layer, mapping to, 203, 241 ULPs (upper layer protocols), 249-253 unbalanced signaling, 15 unfeasible routes length field, 193 unicast poll, ARP cache mechanism, 94 Uniform Resource Identifiers (URIs), 324 Uniform Resource Name (URN), 324 Unix kernel, mount command, 356 untransparent message body, 330 unused, BOOTP (Boot Parameter) protocol headers, 107 unused field, RIPv1 headers, 143
506
TCP/IP PRIMER PLUS
Update messages fields, 192-193 update packets, 187 Update timers, 183 updates, triggered, 149 upgrade field, 328 upper layer protocols (ULPs), 249-253 URG (urgent) control flag, 216 Urgent Pointer (2 bytes), 217 URIs (Uniform Resource Identifiers), 324 URN (Uniform Resource Name), 324 user agents. See UAs User Datagram Protocol. See UDP user datagrams, routing purpose, 125 user interfaces, FTP (File Transfer Protocol), 270 users, NFS, autofs (auto file system), 359 USER [username] command, 279 utilities Ping, 85 echo replies or requests, 74 Echo Reply Type 0, 77-78 traceroute, 85
vendors BOOTP (Boot Parameter) protocol headers, 109 NFS products, 355-356 OSI Reference Model layers, 7 version 2 (NFS) features, 354-355 version 3 (NFS) features, 354-355 version 4 (IP), 64 version field, 143, 192 version number field, 174 versions Ethernet, 14-15 RPC call messages, 362 SNMP (Simple Network Management Protocol), 349 via field, 328 views, MIB (Management Information Bases), 347 virtual links, 172-173 VLSMs (variable length subnet masks), 44, 132 voltage, balanced or unbalanced signaling, 15 VRFY command, 293
well-known mandatory category (path attributes), 195-196 Wide Area Network (WAN), 25-30, 353-354 windowing, stages, 236 windows TCP headers, 217, 235 zero, 236-237 withdrawn routes field, 193 WRQ (request to write), 336-338 WWW (World Wide Web), 251-252, 321
X-Z
X.25 LAPB (Link Access Procedure, Balanced) protocol, 30 X.400 naming model (SMTP), 289-291 XDR (eXternal Data Representation) protocol, 10, 353, 359-360 Zero flag, 307 zero windows, 236-237 zones, domain partitions, 303
W
WAN (Wide Area Network), 25-30, 353-354 warning field, 328 Web browsers, HTTP (Hypertext Transfer Protocol), 323 Web sites RFCs (Request for Comments), 31 routing tables, 188 well-known discretionary attribute, 196-198 well-known discretionary category (path attributes), 195-197 well-known mandatory attribute, 195-196
V
values ACK (acknowledgement), 212-214 object ID and value, 350-351 variable length subnet masks (VLSMs), 44 variable-length options, TCP headers, 217-218 vectors, distance-vector routing protocols, 129-131

TCP IP Primer Plus

Uploaded by

Copyright:

Available Formats

TCP IP Primer Plus

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TCP IP Primer Plus

Uploaded by

Copyright:

Available Formats

What are the main chapters covered in the book?

What are the main chapters covered in the book?

What protocols are discussed in chapters 7-10?

What protocols are discussed in chapters 7-10?

TCP/IP Primer Plus

201 West 103rd St., Indianapolis, Indiana, 46290 USA

TCP/IP Primer Plus

Christina Smith Emily Morgan

Kelly Thompson Plan-it Publishing

Warning and Disclaimer

C H A P T E R 1 : Overview of Industry Models and Standards

TCP/IP PRIMER PLUS

C H A P T E R 6 : Routing Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137

TCP/IP PRIMER PLUS

TCP/IP PRIMER PLUS

C H A P T E R 1 4 : Name Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .299

TCP/IP PRIMER PLUS

C H A P T E R 1 6 : Trivial File Transfer Protocol (TFTP)

C H A P T E R 1 7 : SNMP (Simple Network Management Protocol) . . . . . . . . . . . . .345

Numeric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .434

TCP/IP PRIMER PLUS

Chapter 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .478 Chapter 18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .479

ABOUT THE AUTHOR

TELL US WHAT YOU THINK!

TCP/IP PRIMER PLUS

OVERVIEW OF INDUSTRY MODELS AND STANDARDS

You will learn about the following in this chapter:

Overview of the OSI Reference Model

TCP/IP PRIMER PLUS

OSI Model and Functions

Data translation, conversion, encryption, decryption, compression

Session management and dialog control

End-to-end communication between programs/processes

Logical addressing and routing

Frame transmission and reception

Signal encoding, media and connectors

Chapter 1 OVERVIEW OF INDUSTRY MODELS AND STANDARDS

Overview of the Department of Defense Model

TCP/IP PRIMER PLUS

The DoD model consists of four distinct layers.

Benefits of the OSIs Layered Design

Layer Functions Clarified

Chapter 1 OVERVIEW OF INDUSTRY MODELS AND STANDARDS

Well-defined Framework for Vendors

Reduced Networking Complexity

General Description of OSI Layers

TCP/IP PRIMER PLUS

Application Presentation Session Transport Network Data Link Physical

Application Presentation Session Transport Network Data Link Physical

Chapter 1 OVERVIEW OF INDUSTRY MODELS AND STANDARDS

Application Presentation Session Transport Network Datalink Physical

Messages Messages Messages Segments Datagrams or Packets Frames Bits 1 0 1 0 1 0 s CRC

TCP/IP PRIMER PLUS

Chapter 1 OVERVIEW OF INDUSTRY MODELS AND STANDARDS

TCP/IP PRIMER PLUS

Data Link Layer

Chapter 1 OVERVIEW OF INDUSTRY MODELS AND STANDARDS

TCP/IP PRIMER PLUS

Data Link Architecture and Topologies

Ethernet and IEEE 802.3