Electrical Wiring Sceme Nissan Patrol

Go to SUP8 1st Rev.
GI
ELECTRICAL SYSTEM
MA
MODIFICATION NOTICE:
SECTION EL EM
LC
EC
I Wiring Diagrams have been changed.
I Harness layout has been changed.
FE
CONTENTS CL
POWER SUPPLY ROUTING/WAGON AND Wiring Diagram - WARN - .........................................62 MT

HARDTOP MODELS .......................................................3 A/T INDICATOR/WAGON AND HARDTOP
Schematic ....................................................................3 MODELS ........................................................................67
Wiring Diagram - POWER - ........................................4 Wiring Diagram - AT/IND -/TB48 Engine Models
AT
POWER SUPPLY ROUTING/PICKUP MODELS..........14 with A/T ......................................................................67
Schematic ..................................................................14 REAR WIPER AND WASHER/WAGON AND TF
Wiring Diagram - POWER - ......................................15 HARDTOP MODELS .....................................................68
STARTING SYSTEM/WAGON AND HARDTOP Wiring Diagram - WIP/R -..........................................68
MODELS ........................................................................20 CIGARETTE LIGHTER/WAGON AND HARDTOP PD
Wiring Diagram - START -/A/T Models with TB48 MODELS ........................................................................70
Engine........................................................................20 Wiring Diagram - CIGAR -/RHD Models ...................70
Wiring Diagram - START -/A/T Models with ZD30 REAR WINDOW DEFOGGER/WAGON AND FA
Engine........................................................................21 HARDTOP MODELS .....................................................71
HEADLAMP/WAGON AND HARDTOP MODELS - Wiring Diagram - DEF -/LHD Models........................71
RA
Daytime Light System - ...............................................22 AUDIO/WAGON AND HARDTOP MODELS.................73
Wiring Diagram - DTRL -...........................................22 Schematic/LHD Models with Sub-harness ................73
TURN SIGNAL AND HAZARD WARNING LAMPS/ Wiring Diagram - AUDIO -/LHD Models with Sub- BR
WAGON AND HARDTOP MODELS .............................24 harness ......................................................................74
Schematic ..................................................................24 Schematic/RHD Models with Sub-harness ...............77
Wiring Diagram - TURN -/Type A..............................25 Wiring Diagram - AUDIO -/RHD Models with ST
Wiring Diagram - TURN -/Type B..............................30 Sub-harness...............................................................78
Wiring Diagram - TURN -/Type D .............................32 Schematic/LHD Models without Sub-harness ...........81
ILLUMINATION/WAGON AND HARDTOP Wiring Diagram - AUDIO -/LHD Models without
RS
MODELS ........................................................................34 Sub-harness...............................................................82
Schematic ..................................................................34 Schematic/RHD Models without Sub-harness ..........86 BT
Wiring Diagram - ILL - ...............................................35 Wiring Diagram - AUDIO -/RHD Models without
METER AND GAUGES/WAGON AND HARDTOP Sub-harness...............................................................87
MODELS ........................................................................43 NAVIGATION SYSTEM .................................................91 HA
Combination Meter ....................................................43 Traffic Information (RDS-TMC)..................................91
Schematic ..................................................................44 Component Parts Location ........................................91
Wiring Diagram - METER - .......................................45 Schematic ..................................................................92
WARNING LAMPS/WAGON AND HARDTOP Wiring Diagram - NAVI -/LHD Models.......................93
MODELS ........................................................................48 Wiring Diagram - NAVI -/RHD Models ....................100 SE
Schematic ..................................................................48 Terminals and Reference Value for NAVI Control
Wiring Diagram - WARN - .........................................50 Unit...........................................................................107
WARNING LAMPS/PICKUP MODELS .........................61 Terminals and Reference Value for Display ............109 IDX
Schematic ..................................................................61 Terminals and Reference Value for NAVI Switch ....110
EL-1
CONTENTS (Cont’d)
Terminals and Reference Value for Transfer Unit ...110 Wiring Diagram - D/LOCK -/Without Theft
Terminals and Reference Value for TMC Tuner......112 Warning System Models..........................................165
Terminals and Reference Value for Voice MULTI-REMOTE CONTROL SYSTEM/WAGON
Change Relay ..........................................................113 AND HARDTOP MODELS ..........................................169
Special Note for Trouble Diagnosis.........................114 Wiring Diagram - MULTI -/For Australia ..................169
On Board Self-Diagnosis Function ..........................114 THEFT WARNING SYSTEM/WAGON AND
Self Diagnosis Mode................................................115 HARDTOP MODELS ...................................................171
Confirmation/Adjustment Mode ...............................119 Schematic ................................................................171
All Images Are Not Displayed..................................126 Wiring Diagram - THEFT -/LHD Models..................172
Vehicle Mark Is Not Displayed Properly..................134 Wiring Diagram - THEFT -/RHD Models .................177
Tint Is Strange for The RGB Image ........................135 CAN SYSTEM/TB48 ENGINE MODELS WITH A/T ...182
RGB Image Is Rolling..............................................137 Wiring Diagram - CAN - ..........................................182
Values for All Items in the Drive Computer HARNESS LAYOUT ....................................................183
Screen Do Not Change ...........................................138 How to Read Harness Layout .................................183
Values for Items, ″Driving Distance″ and HARNESS LAYOUT/WAGON AND HARDTOP
″Average Speed″ Do Not Change...........................138 MODELS ......................................................................184
Voice Guidance Is Not Heard..................................138 Main Harness/LHD Models......................................184
RDS-TMC (Traffic Information) Is Not Received.....142 Main Harness/RHD Models .....................................188
Example of Symptoms Judged Not Malfunction .....143 Engine Room Harness/LHD Models .......................192
HEATED SEAT/WAGON AND HARDTOP Engine Room Harness/RHD Models.......................196
MODELS ......................................................................146 Engine Harness .......................................................200
Wiring Diagram - HSEAT - ......................................146 Engine Control Harness ..........................................202
AUTOMATIC SPEED CONTROL DEVICE (ASCD)/ Body Harness/LHD Models .....................................204
WAGON AND HARDTOP MODELS ...........................148 Body Harness/RHD Models.....................................206
Schematic ................................................................148 Body No. 2 Harness/LHD Models ...........................210
Wiring Diagram - ASCD - ........................................149 Body No. 2 Harness/RHD Models...........................212
POWER WINDOW/WAGON AND HARDTOP Room Lamp Harness...............................................214
MODELS ......................................................................153 HARNESS LAYOUT/PICKUP MODELS .....................216
Schematic ................................................................153 Main Harness/RHD Models .....................................216
Wiring Diagram - WINDOW - ..................................154 FUSE AND FUSIBLE LINK BOX/WAGON AND
POWER DOOR LOCK/WAGON AND HARDTOP HARDTOP MODELS .............................................Foldout
MODELS ......................................................................159 Terminal Arrangement........................................Foldout
Schematic/With Theft Warning System Models ......159 FUSE AND FUSIBLE LINK BOX/PICKUP
Wiring Diagram - D/LOCK -/RHD Models With MODELS ................................................................Foldout
Theft Warning System .............................................160 Terminal Arrangement........................................Foldout
Schematic/Without Theft Warning System
Models .....................................................................164
EL-2
POWER SUPPLY ROUTING/WAGON AND HARDTOP MODELS
Schematic GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL256N IDX
EL-3
Wiring Diagram — POWER —

BATTERY POWER SUPPLY — IGNITION SW. IN ANY POSITION
TEL191N
EL-4
Wiring Diagram — POWER — (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL257N
IDX
EL-5
TEL258N
EL-6
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL193N
IDX
EL-7
TEL259N
EL-8
ACCESSORY POWER SUPPLY — IGNITION SW. IN “ACC” OR “ON” GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL260N
IDX
EL-9
IGNITION POWER SUPPLY — IGNITION SW. IN “ON” AND/OR “START”
TEL195N
EL-10
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL969M
IDX
EL-11
TEL970M
EL-12
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL261N
IDX
EL-13
POWER SUPPLY ROUTING/PICKUP MODELS
Schematic
TEL309N
EL-14
Wiring Diagram — POWER — GI

BATTERY POWER SUPPLY — IGNITION SW. IN ANY POSITION
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
TEL310N
EL-15
TEL311N
EL-16
ACCESSORY POWER SUPPLY — IGNITION SW. IN “ACC” OR “ON” GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL312N
IDX
EL-17
IGNITION POWER SUPPLY — IGNITION SW. IN “ON” AND/OR “START”
TEL313N
EL-18
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL314N
IDX
EL-19
STARTING SYSTEM/WAGON AND HARDTOP MODELS
Wiring Diagram — START —/A/T Models with

TB48 Engine
TEL196N
EL-20
STARTING SYSTEM/WAGON AND HARDTOP MODELS
Wiring Diagram — START —/A/T Models with GI

ZD30 Engine
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
TEL197N
EL-21
HEADLAMP/WAGON AND HARDTOP MODELS — Daytime Light System —
Wiring Diagram — DTRL —
TEL198N
EL-22
HEADLAMP/WAGON AND HARDTOP MODELS — Daytime Light System —
Wiring Diagram — DTRL — (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL199N
IDX
EL-23
TURN SIGNAL AND HAZARD WARNING LAMPS/WAGON AND HARDTOP
MODELS
Schematic
LHD MODELS EXCEPT FOR EUROPE AND CHINA (TYPE A)
Rear combination lamps are not located on rear bumper.
TEL997M
EL-24
MODELS
Wiring Diagram — TURN —/Type A GI

LHD MODELS EXCEPT FOR EUROPE AND CHINA
Rear combination lamps are not located on rear bumper. MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
TEL998M
EL-25
MODELS
Wiring Diagram — TURN —/Type A (Cont’d)
TEL999M
EL-26
MODELS
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL262N
IDX
EL-27
MODELS
RHD MODELS EXCEPT FOR EUROPE, AUSTRALIA AND SOUTH AFRICA
TEL002N
EL-28
MODELS
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL263N
IDX
EL-29
MODELS
Wiring Diagram — TURN —/Type B

FOR CHINA
Rear combination lamps are located on rear bumper.
TEL004N
EL-30
MODELS
Wiring Diagram — TURN —/Type B (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL264N
IDX
EL-31
MODELS
Wiring Diagram — TURN —/Type D

FOR AUSTRALIA AND SOUTH AFRICA
Rear combination lamps are located on rear bumper.
TEL325N
EL-32
MODELS
Wiring Diagram — TURN —/Type D (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL266N
IDX
EL-33
ILLUMINATION/WAGON AND HARDTOP MODELS
Schematic
TEL267N
EL-34
Wiring Diagram — ILL — GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL011N IDX
EL-35
Wiring Diagram — ILL — (Cont’d)
TEL012N
EL-36
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL013N
IDX
EL-37
TEL014N
EL-38
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL268N
IDX
EL-39
TEL204N
EL-40
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL017N
IDX
EL-41
TEL018N
EL-42
METER AND GAUGES/WAGON AND HARDTOP MODELS
Combination Meter GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
CEL587M IDX
EL-43
Schematic
TEL022N
EL-44
Wiring Diagram — METER — GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL023N IDX
EL-45
Wiring Diagram — METER — (Cont’d)
TEL205N
EL-46
NOTE
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
EL-47
WARNING LAMPS/WAGON AND HARDTOP MODELS
Schematic
TEL899M
EL-48
Schematic (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL251N
IDX
EL-49
Wiring Diagram — WARN —
TEL206N
EL-50
Wiring Diagram — WARN — (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL207N
IDX
EL-51
TEL903M
EL-52
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL904M
IDX
EL-53
TEL905M
EL-54
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL906M
IDX
EL-55
TEL208N
EL-56
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL252N
IDX
EL-57
TEL209N
EL-58
LHD MODELS GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL910M
IDX
EL-59
RHD MODELS
TEL026N
EL-60
WARNING LAMPS/PICKUP MODELS
Schematic GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL315N IDX
EL-61
Wiring Diagram — WARN —
TEL316N
EL-62
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL317N
IDX
EL-63
TEL318N
EL-64
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL319N
IDX
EL-65
TEL320N
EL-66
A/T INDICATOR/WAGON AND HARDTOP MODELS
Wiring Diagram — AT/IND —/TB48 Engine GI

Models with A/T
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
TEL210N
EL-67
REAR WIPER AND WASHER/WAGON AND HARDTOP MODELS
Wiring Diagram — WIP/R —

LHD MODELS
TEL211N
EL-68
REAR WIPER AND WASHER/WAGON AND HARDTOP MODELS
Wiring Diagram — WIP/R — (Cont’d)
LHD MODELS GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL033N
IDX
EL-69
CIGARETTE LIGHTER/WAGON AND HARDTOP MODELS
Wiring Diagram — CIGAR —/RHD Models
TEL212N
EL-70
REAR WINDOW DEFOGGER/WAGON AND HARDTOP MODELS
Wiring Diagram — DEF —/LHD Models GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL213N IDX
EL-71
REAR WINDOW DEFOGGER/WAGON AND HARDTOP MODELS
Wiring Diagram — DEF —/LHD Models (Cont’d)
TEL214N
EL-72
AUDIO/WAGON AND HARDTOP MODELS
Schematic/LHD Models with Sub-harness GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL217N IDX
EL-73
Wiring Diagram — AUDIO —/LHD Models with

Sub-harness
TEL218N
EL-74
Sub-harness (Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL050N
IDX
EL-75
Sub-harness (Cont’d)
TEL051N
EL-76
Schematic/RHD Models with Sub-harness GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL219N IDX
EL-77
Wiring Diagram — AUDIO —/RHD Models with

Sub-harness
TEL220N
EL-78
Sub-harness (Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL055N
IDX
EL-79
Sub-harness (Cont’d)
TEL056N
EL-80
Schematic/LHD Models without Sub-harness GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL221N IDX
EL-81
Wiring Diagram — AUDIO —/LHD Models

without Sub-harness
TEL222N
EL-82
without Sub-harness (Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL059N
IDX
EL-83
without Sub-harness (Cont’d)
TEL060N
EL-84
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL223N
IDX
EL-85
Schematic/RHD Models without Sub-harness
TEL224N
EL-86
Wiring Diagram — AUDIO —/RHD Models GI

without Sub-harness
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
TEL225N
EL-87
Wiring Diagram — AUDIO —/RHD Models
TEL064N
EL-88
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL065N
IDX
EL-89
TEL066N
EL-90
NAVIGATION SYSTEM
Traffic Information (RDS-TMC) GI

SYSTEM DESCRIPTION
Refer to owner’s manual or navigation system owner’s manual for the system operation. MA
The Traffic Information broadcast allows to you to avoid delays due to traffic incidents.
Traffic jams, roadwork, closed roads around your current location, etc. are represented graphically on the map
by icons depicting the nature of the event. EM
Incidents on the route are automatically brought to your attention when they are approached.
The Traffic Information feature gives you the opportunity to forecast traffic incidents, determine how serious
they are and, via the guidance mode, allows you to detour around traffic incidents. LC
The navigation system receives traffic information from best available sources and enables the RDS-TMC
(Radio Data System-Traffic Message Channel) to inform and guide you.
The RDS-TMC broadcast is fed by a dedicated FM tuner so that you can still tune your radio station while EC
Traffic Information is being broadcasted.
Component Parts Location FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
PKIC6342E
HA
SE
IDX
EL-91
NAVIGATION SYSTEM
Schematic
TEL226N
EL-92
NAVIGATION SYSTEM
Wiring Diagram — NAVI —/LHD Models GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL227N IDX
EL-93
NAVIGATION SYSTEM
Wiring Diagram — NAVI —/LHD Models
(Cont’d)
TEL228N
EL-94
NAVIGATION SYSTEM
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL229N
IDX
EL-95
NAVIGATION SYSTEM
(Cont’d)
TEL230N
EL-96
NAVIGATION SYSTEM
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL231N
IDX
EL-97
NAVIGATION SYSTEM
(Cont’d)
TEL232N
EL-98
NAVIGATION SYSTEM
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL233N
IDX
EL-99
NAVIGATION SYSTEM
Wiring Diagram — NAVI —/RHD Models
TEL234N
EL-100
NAVIGATION SYSTEM
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL235N
IDX
EL-101
NAVIGATION SYSTEM
(Cont’d)
TEL236N
EL-102
NAVIGATION SYSTEM
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL237N
IDX
EL-103
NAVIGATION SYSTEM
(Cont’d)
TEL238N
EL-104
NAVIGATION SYSTEM
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL239N
IDX
EL-105
NAVIGATION SYSTEM
(Cont’d)
TEL240N
EL-106
NAVIGATION SYSTEM
Terminals and Reference Value for NAVI GI

Control Unit
MA
Terminal No.
Signal Condition
(Wire color)
Item input/ Reference value Example of symptom
Ignition
(+) (-) output
switch
Operation EM
1 (B) Ground Ground — ON — Approx. 0 V —
Battery
2 (R/G) Ground power sup- Input OFF — Battery voltage
System does not work LC
properly.
ply
5 ACC power System does not work
Ground Input ACC — Battery voltage
(L/OR) supply properly. EC
FE
Only route guidance and
Voice guid- Press the “VOICE”
12 (Y) 14 (BR) Output ON operation guidance are
ance signal switch.
not heard.
CL
SKIB3597E
13 — Shield — — — — — MT
Select “Color bar” of AT

RGB signal CONFIRMATION/ RGB screen looks blu-
44 (R) Ground Output ON
(R: red) ADJUSTMENT func- ish.
tion.
TF
SKIB7360E
PD
Select “Color bar” of
45 (G) Ground
RGB signal
(G: green)
Output ON
CONFIRMATION/
ADJUSTMENT func-
RGB screen looks red-
dish.
FA
tion.
SKIB7361E
RA
BR
RGB signal CONFIRMATION/ RGB screen looks yel-
46 (B) Ground Output ON
(B: blue) ADJUSTMENT func- lowish.
tion. ST
SKIB7362E
47 — Shield — — — — —
RS
BT
RGB syn-
48 (W) Ground chronizing Output ON — RGB screen is rolling.
signal
HA
SKIB3603E
RGB area RGB screen is not

50 (R) Ground Output ON — Approx. 5 V
(YS) signal shown.
Lighting switch posi-
Approx. 12 V
61 (L/B) Ground
Illumination
Input ON
tion 1st or 2nd Night illumination for
switches does not illumi-
SE
signal Lighting switch posi-
Approx. 0 V nate.
tion OFF
IDX
EL-107
NAVIGATION SYSTEM
Terminals and Reference Value for NAVI
Control Unit (Cont’d)
Terminal No.
Signal Condition
(Wire color)
output Ignition
(+) (-) Operation
switch
63 Vehicle information set-
Ground IGN signal Input ON — Battery voltage.
(R/W) ting is not possible.
The navigation current-
Select R-position Approx. 12 V location mark moves
Reverse
65 (Y) Ground Input ON strangely when the
signal
Other position Approx. 0 V vehicle is moving back-
wards.
NOTE:
Maximum voltage may be 5 V due to
specifications (connected units).
Vehicle When vehicle speed Navigation current-loca-

66
Ground speed signal Input ON is approx. 40 km/h tion mark does not indi-
(R/W)
(8-pulse) (25 MPH) cate the correct position.
PKIA1935E
68 — Shield — — — — —
Communica-
69 Input/ System does not work
Ground tion signal ON —
(W) Output properly.
(+)
SKIB7378E
Communica-
Input/ System does not work
70 (B) Ground tion signal ON —
Output properly.
(-)
SKIB7379E
Communica-
71 (R) Ground tion signal ON —
Output properly.
(+)
SKIB7378E
Communica-
72 (G) Ground tion signal ON —
Output properly.
(-)
SKIB7379E
GPS
Connector is not GPS correction is not
73 Ground antenna sig- Input ON Approx. 5 V
connected. possible.
nal
74 — Shield — — — — —
EL-108
NAVIGATION SYSTEM
Terminals and Reference Value for Display GI

Terminal No.
Signal Condition
(Wire color)
Item input/ Reference value Example of symptom MA
output Ignition
(+) (-) Operation
switch
EM
RGB signal CONFIRMATION/ RGB screen looks blu-
1 (R) Ground
(R: red)
Input ON
ADJUSTMENT func- ish. LC
tion.
SKIB7360E EC
Select “Color bar” of FE

RGB signal CONFIRMATION/ RGB screen looks red-
2 (G) Ground Input ON
(G: green) ADJUSTMENT func- dish.
tion.
CL
SKIB7361E
MT
RGB signal CONFIRMATION/ RGB screen looks yel-
3 (B) Ground
(B: blue)
Input ON
ADJUSTMENT func- lowish. AT
tion.
SKIB7362E TF
4 — Shield — — — — —
PD
RGB synchro-
7 (W) Ground Input ON — RGB screen is rolling.
nizing signal FA
SKIB3603E
RA
RGB area (YS) RGB screen is not
8 (R) Ground Input ON — Approx. 5 V
signal shown.
BR
Communication
System does not work
15 (OR) Ground signal
(DISP-SW)
Output ON —
properly. ST
SKIB3606E RS
BT
Communication
16 (B) Ground signal Input ON —
properly.
(NAVI-DISP)
HA
SKIB3607E
17 — Shield — — — — —
(L/OR) supply properly.
21 Battery power System does not work
(R/G)
Ground
supply
Input OFF — Battery voltage
properly. SE
23 Battery power System does not work
Ground Input — — Battery voltage
(R/G) supply properly. IDX
EL-109
NAVIGATION SYSTEM
Terminals and Reference Value for NAVI Switch

Terminal No.
Signal Condition
(Wire color)
output Ignition
(+) (-) Operation
switch
1 ACC power All operations do not
(L/OR) supply work.
Lighting switch posi-
Approx. 12 V Night illumination for
Illumination tion 1st or 2nd
2 (L/B) 3 (B) Input OFF switches does not illumi-
signal Lighting switch posi-
Approx. 0 V nate.
tion OFF
Communica-
4 (OR) Ground tion signal Input ON —
properly.
(DISP-SW)
SKIB3606E
Communica-
5 (L/W) Ground tion signal Output ON —
properly.
(SW-NAVI)
SKIB3611E
6 — Shield — — — — —
All operations do not
7 (B) Ground Ground — ON — Approx. 0 V
work.
Terminals and Reference Value for Transfer

Unit
Terminal No.
Signal Condition
(Wire color)
output Ignition
(+) (-) Operation
switch

1 (L) 2 (PU) Output ON operation guidance are
ance signal switch.
not heard.
SKIB3609E
Voice
change Press the “VOICE”
6 (BR) 4 (R) Output ON operation guidance are
relay ON switch.
not heard.
signal
SKIB3610E
7 — Shield — — — — —
EL-110
NAVIGATION SYSTEM
Terminals and Reference Value for Transfer
Unit (Cont’d) GI
Terminal No.
Condition
(Wire color)
Item
Signal
input/ Reference value Example of symptom
MA
output Ignition
(+) (-) Operation
switch
EM

8 (Y) 10 (BR)
Voice guid-
Input ON
Press the “VOICE”
operation guidance are LC
ance signal switch.
not heard.
SKIB3597E
EC
9 — Shield — — — — —
FE
Communica-
11
(W)
Ground tion signal
Input/
Output
ON —
properly.
CL
(+)
SKIB7378E
MT
AT
Communica-
13 (B) Ground tion signal ON —
Output properly.
(-) TF
SKIB7379E
15 — Shield — — — — —
PD
FA
Communica-
18 System does not work
Ground tion signal Input ON —
(L/W) properly.
(SW-NAVI)
RA
SKIB3611E
19 — Shield — — — — —
BR
ST
Communica-
20 (B) Ground tion signal Output ON —
properly.
(NAVI-DISP)
RS
SKIB3607E
25 (B) Ground Ground — ON — Approx. 0 V — BT

(L/OR)
Ground
supply
Input ACC — Battery voltage
properly.
HA
Battery
Ground power sup- Input OFF — Battery voltage
(R/G) properly.
ply
Battery
Ground power sup- Input OFF — Battery voltage
(R/G) properly.
ply SE
IDX
EL-111
NAVIGATION SYSTEM
Terminals and Reference Value for TMC Tuner

Terminal No.
Signal input/ Condition
(Wire color) Item Reference value
output
(+) (-) Ignition switch Operation
Communica-
1 (R) Ground tion signal Input/Output ON —
(+)
SKIB7378E
Communica-
2 (G) Ground tion signal Input/Output ON —
(-)
SKIB7379E
3 — Shield — — — —
Battery
5 (R/G) Ground power sup- Input OFF — Battery voltage
ply
ACC power
7 (L/OR) Ground Input ACC — Battery voltage
supply
8 (B) Ground Ground — ON — Approx. 0 V
EL-112
NAVIGATION SYSTEM
Terminals and Reference Value for Voice GI

Change Relay
MA
Terminal No.
Signal Condition
(Wire color)
Ignition
(+) (-) output
switch
Operation EM
LC
Voice
change Press the “VOICE”
2 (BR) 1 (R) Input ON operation guidance are
relay ON switch.
not heard.
signal EC
SKIB3610E
FE
3 (OR) 5 (G)
Audio sound
signal Input ON
Receive audio sig-
No sound from door
speaker and tweeter
CL
nal.
(driver side) (driver side).
MT
SKIB3609E
AT
4 8 Only route guidance and
(L)*1 (B/W)*1 Output ON operation guidance are
ance signal switch.
(BR)*2 (B/R)*2 not heard. TF
SKIB3609E
PD
Only route guidance and FA

6 (L) 7 (PU) Input ON operation guide are not
ance signal switch.
heard.
RA
SKIB3609E
*1: LHD models.

*2: RHD models.
BR
ST
RS
BT
HA
SE
IDX
EL-113
NAVIGATION SYSTEM
Special Note for Trouble Diagnosis

Prior to perform trouble diagnosis, make sure there are no corresponding description in the “Example of
Symptoms Possible No Malfunction”. Refer to EL-143, “Example of Symptoms Judged Not Malfunction”.
On Board Self-Diagnosis Function
DESCRIPTION
I Trouble diagnosis function of navigation system has a Self Diagnosis mode by automatic operation and a
Confirmation/Adjustment mode by manual operation.
I Self Diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the display.
I Confirmation/Adjustment mode displays trouble diagnosis that require an operation and a judgment by a
human (auto-decision cannot be performed by the system), confirmation of preset value, and an error his-
tory.
DIAGNOSIS ITEM
Mode Description
I NAVI Control unit diagnosis (DVD-ROM drive will not be diagnosed when no
DVD-ROM is in it.).
Self Diagnosis I Analyzes connection between the NAVI control unit and the GPS antenna, con-
nection between the NAVI control unit and each unit, and operation of each
unit.
Color tone and shading of the screen can be checked by the display of a color
Display Diagnosis
bar and a gray scale.
Diagnosis of signals that are input to NAVI control unit can be performed for
Vehicle Signals
Vehicle speed, Lights, Ignition and Reverse.
Steering Angle This mode is used to correct difference between actual turning angle of a vehicle
Adjustment and turning angle of the vehicle mark on the display.
Under ordinary conditions, the navigation system distance measuring function will
Navigation automatically compensate for minute decreases in wheel and tire diameter
Confirmation/ Speed Calibra-
caused by tire wear or low-pressure. Speed Calibration can immediately restore
Adjustment tion
system accuracy in cases such as when distance calibration is needed because
of the use of tire chains.
Malfunctions that occurred in the past are displayed, along with the number of
Error History times each has occurred. Time and location when/where the errors occurred are
also displayed.
Delete Unit Connection Log Erase the connection history of unit and error history.
Operations of navigation system that are performed while driving can be
Feature Restriction Setting
restricted by using this function.
EL-114
NAVIGATION SYSTEM
Self Diagnosis Mode GI

OPERATION PROCEDURE
1. Start the engine. MA
2. Press and hold “MAP” and “ ” buttons simultaneously for 5
seconds or more.
I Shifting from current screen to previous screen is per- EM
formed by pressing “BACK” button.
LC
PKIB1537E
3. The initial trouble diagnosis screen will be shown, and items EC

“Self Diagnosis” and “Confirmation/Adjustment” will become
selective.
FE
CL
MT
SKIB6971E
AT
4. Perform self-diagnosis by selecting the “Self Diagnosis”.
I Self-diagnosis screen is displayed, and then self-diagnosis
starts. TF
I The bar graph visible below self-diagnosis screen displays
progress of the diagnosis.
PD
FA
SKIB6972E
RA
5. On the diagnosis results screen, each unit name and connec-
tion line will be colored according to the diagnosis result, as
follows. BR
Connection
Diagnosis results Unit
line ST
Normal Green Green
Connection malfunction Gray Yellow RS
DVD-ROM drive undiagnosed Gray Green
DVD-ROM and DVD-ROM drive malfunction Yellow Green
SKIB7631E BT
Unit returned an error Red Green
NOTE: HA
I Control unit = NAVI control unit
I Converter = Transfer unit
I Switch = NAVI switch
I TMC BB = TMC tuner
I Only Control unit (NAVI control unit) is displayed in red.
I If multiple malfunctions occur at the same time for a single unit, SE
the screen switch colors are determined according to the fol-
lowing order of priority: red > yellow > gray.
IDX
EL-115
NAVIGATION SYSTEM
Self Diagnosis Mode (Cont’d)
6. Select a switch on the diagnosis results screen, and comments
for the diagnosis results will be shown.
SKIB3659E
EL-116
NAVIGATION SYSTEM
SELF-DIAGNOSIS RESULT GI
Check the applicable display in the following table, and then repair the malfunctioning parts.
Quick Reference Table MA

Self-diagnosis result screen Possible cause Action to take
EM
LC
NAVI control unit malfunction is

detected.
Replace NAVI control unit. EC
FE
SKIB7632E
CL
1. Check if the inserted DVD-ROM is
specified for this navigation
system, and the DVD-ROM is dirty,
MT
I Malfunction is detected on DVD- scratched or warped.
ROM drive pickup lens in NAVI 2. If the results from the above
control unit. checkup show no malfunction,
AT
I There is dirt and damage on the insert the same DVD-ROM, and
DVD-ROM. then restart self-diagnosis.
3. If self-diagnosis results still show
TF
any malfunction, replace NAVI
control unit.
SKIB7633E PD
FA
RA
DVD-ROM not inserted is detected. Insert DVD-ROM.
BR
SKIB7634E
ST
1. Check if GPS antenna feeder line

RS
is snapped or pinched.
2. If the results from the above
checkup show no malfunction,
BT
GPS antenna connection malfunction
replace GPS antenna, and then
is detected.
restart self-diagnosis.
HA
any malfunction, replace NAVI
control unit.
SKIB7635E
SE
IDX
EL-117
NAVIGATION SYSTEM
Self-diagnosis result screen Possible cause Action to take
1. Check TMC tuner power supply
and ground circuit.
2. Check communication circuit
between NAVI control unit and
I TMC tuner power supply and
TMC tuner.
ground circuit malfunction is
3. If the results from the above
detected.
checkup show no malfunction,
I Malfunction is detected on commu-
replace either TMC tuner or NAVI
nication signal between NAVI con-
control unit, and then start self-
trol unit and TMC tuner.
diagnosis.
any malfunction, replace the other
SKIB7636E
unit.
EL-118
NAVIGATION SYSTEM
Confirmation/Adjustment Mode GI
OPERATION PROCEDURE
1. Start the engine. MA
2. Press and hold “MAP” and “ ” buttons simultaneously for 5
seconds or more.
I Shifting from current screen to previous screen is per- EM
formed by pressing “BACK” button.
LC
PKIB1537E
3. The initial trouble diagnosis screen will be shown, and items EC

“Self Diagnosis” and “Confirmation/Adjustment” will become
selective.
FE
CL
MT
SKIB6974E
AT
4. Each diagnosis is shown by selecting each screen switch on
Confirmation/Adjustment screen.
TF
PD
FA
SKIB6975E
RA
BR
ST
RS
BT
HA
SE
IDX
EL-119
NAVIGATION SYSTEM
Confirmation/Adjustment Mode (Cont’d)
DISPLAY DIAGNOSIS
SKIB6976E
I If RGB signal is malfunctioning, the tint of the color bar display is as follows.
R (red) signal error: Light blue (Cyan) tint
G (green) signal error: Purple (Magenta) tint
B (blue) signal error: Yellow tint
VEHICLE SIGNALS
A comparison check can be made of each actual vehicle signal and
the signals recognized by the NAVI control unit.
SKIB6977E
Diagnosis item Display Condition Remarks

ON When vehicle speed is more than 0 km/h (0 MPH)
Changes in indication may be
Vehicle speed OFF When vehicle speed is 0 km/h (0 MPH)
delayed. This is normal.
— Ignition switch in ACC position
ON Lighting switch ON
Lights —
OFF Lighting switch OFF
ON Ignition switch ON
Ignition —
OFF Ignition switch ACC position
ON Selector lever in R position
Changes in indication may be
Reverse OFF Selector lever in any position other than R position
delayed. This is normal.
— Ignition switch in ACC position
NOTE:
If ignition signal is NG, each vehicle signal of vehicle speed and reverse is not displayed.
EL-120
NAVIGATION SYSTEM
NAVIGATION GI
Steering Angle Adjustment
The steering angle output value detected by the gyroscope can be MA
adjusted.
EM
LC
SKIB3684E
Speed Calibration EC
Usually the automatic distance correction function adjusts the mal-
function in distance caused by the tires wearing down or the tire FE
pressure change. If prompt adjustment is necessary when the tire
chains are installed etc., perform this procedure.
CL
MT
SKIB3685E
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
EL-121
NAVIGATION SYSTEM
ERROR HISTORY
Diagnosis results of self-diagnosis depend on if any error occurred during the time after selecting “Self Diag-
nosis” until self-diagnosis results are displayed.
Meanwhile, when an error occurs before selecting “Self Diagnosis”, and if an error does not occur until self-
diagnosis results are displayed, a diagnosis result is judged as normal.
Consequently, a diagnosis needs to be performed with “Error History” for the past error that is not available
with self-diagnosis.
“Error History” displays the time and place of the most recent occurrence of that error. However, take note of
the following points.
I Correct time of the error occurrence may not be displayed when the GPS antenna substrate within the
NAVI control unit has malfunctioned.
I Place of the error occurrence is represented by the position of the vehicle mark at the time when the error
occurred. If the vehicle mark has deviated from the correct position, then the place of the error occurrence
may not be located correctly.
I When the ignition switch is turned ON if the error is detected, the counter increases 1. Even if it is nor-
mal when the ignition switch is turned ON the next time, the counter does not decrease.
I The upper limit of the counter is 50. 51 or more is displayed as 50. It can be reset to 0 by “Delete log”
switch.
SKIB6978E
EL-122
NAVIGATION SYSTEM
Diagnosis by Error History GI
I When having a difficulty on the investigation of cause due to multiple errors with a reproducible
malfunction, turn ON the ignition switch from OFF mode after making a memo of the item and number of
time (or delete “Error History”). Check “Error History” again after the malfunction was reproduced, and then MA
perform diagnosis focusing on the item of which number of time increased.
I DVD-ROM error history may be restored because DVD-ROM cannot be temporarily read. (Driving on rough
road etc.) Then, erase the error history. (This is not a malfunction.) Perform service in “Action to take” if EM
error history are repeatedly indicated again.
Error item Possible cause Action to take LC
1. Start self-diagnosis, and make sure of
the result.
2. If any error is found, GO TO 3. If any
EC
error is not found, delete the error his-
tory and end the diagnosis. (This is not
a malfunction.)
FE
GPS antenna connection malfunction is 3. Check if GPS antenna feeder line is
GPS Antenna Error
detected. snapped or pinched.
CL
4. If the results from the above checkup
show no malfunction, replace GPS
antenna, and then restart self-diagno- MT
sis.
5. If self-diagnosis results still show any
malfunction, replace NAVI control unit. AT
FLASH-ROM Error Of Control Unit the result.
2. If any error is found, replace NAVI con- TF
NAVI control unit malfunction is detected.
trol unit. If any error is not found, delete
Connection Of Gyro the error history and end the diagnosis.
(This is not a malfunction.) PD
GPS Communication Error
If the symptoms such as the GPS receipt
Transmission error: GPS-Main CPU
malfunction occur, intermittent malfunction
FA
Receive error: GPS-Main CPU caused by strong radio interference may
GPS malfunction is detected.
be detected.
GPS ROM Error RA
If the malfunction always occurs, replace
GPS RAM Error
NAVI control unit.
GPS RTC Error
BR
DVD-ROM Mechanism not Detected
DVD-ROM Communication Error
ST
DVD-ROM Mechanism Error
1. Check if the inserted DVD-ROM is
DVD-ROM Focus Error
DVD-ROM TOC Error
specified for this navigation system, RS
and the DVD-ROM is dirty, scratched
DVD-ROM Disc Error I Malfunction is detected on DVD-ROM or warped.
DVD-ROM Seek Error

drive pickup lens in NAVI control unit. 2. If the results from the above checkup BT
I There is dirt and damage on the DVD- show no malfunction, insert the same
DVD-ROM Error Correction Error ROM. DVD-ROM, and then restart self-diag-
DVD-ROM Read Error nosis. HA
DVD-ROM Data Transfer Error
malfunction, replace NAVI control unit.
DVD-ROM Data Error
DVD-ROM Loading/Eject Error
DVD-ROM Time-out SE
IDX
EL-123
NAVIGATION SYSTEM
Error item Possible cause Action to take
1. Delete the error history, and turn OFF
ignition switch.
2. Turn ON ignition switch, and make sure
of the error history.
3. If the error item listed left is displayed
again, GO TO 4. If the error item is not
displayed, end the diagnosis. (This is
I Transfer unit power supply and ground
not a malfunction.)
circuit malfunction is detected.
4. Check transfer unit power supply and
Converter Connection Error I Malfunction is detected on communica-
ground circuit.
tion signal between NAVI control unit
5. Check communication circuit between
and transfer unit.
NAVI control unit and transfer unit.
show no malfunction, replace either
transfer unit or NAVI control unit, and
then start self-diagnosis.
malfunction, replace the other unit.
the result.
2. If any error is found, GO TO 3. If any
error is not found, delete the error his-
tory and end the diagnosis. (This is not
a malfunction.)
I TMC tuner power supply and ground
3. Check TMC tuner power supply and
circuit malfunction is detected.
ground circuit.
RDS-TMC Error I Malfunction is detected on communica-
4. Check communication circuit between
tion signal between NAVI control unit
NAVI control unit and TMC tuner.
and TMC tuner.
show no malfunction, replace either
TMC tuner or NAVI control unit, and
then start self-diagnosis.
malfunction, replace the other unit.
EL-124
NAVIGATION SYSTEM
DELETE UNIT CONNECTION LOG GI
Erase the connection history of unit and error history that is
recorded in NAVI control unit (clear the connection history of the
removed unit). MA
EM
LC
SKIB6979E
FEATURE RESTRICTION SETTING EC

Operations of navigation system that are performed while driving
can be restricted by using this function. FE
CAUTION:
Once operational restrictions are imposed, they cannot be
cancelled even when the software is updated or the language- CL
switching program is loaded.
MT
SKIB6980E
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
EL-125
NAVIGATION SYSTEM
All Images Are Not Displayed

Symptom: All images are not displayed. (Navigation system does
not start.)
1. CHECK CONDITION
1. Turn ignition switch ON.
2. Press and hold “MAP” and “ ” buttons simultaneously for 5 seconds or more.
Does NAVI switch sound a beep twice?
YES © GO TO 2.
NO © GO TO 5.
2. CHECK NAVI CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

1. Check voltage between NAVI control unit harness connector terminals and ground.
SKIB7018E
Terminals
(+) OFF ACC ON
(-)
Connector Terminal
2 Battery voltage Battery voltage Battery voltage
M179 Ground
5 0V Battery voltage Battery voltage
2. Turn ignition switch OFF.

3. Disconnect NAVI control unit connector.
4. Check continuity between NAVI control unit harness connector M179 terminal 1 and ground.
1 - Ground: Continuity should exist.
SKIB7019E
OK or NG
OK © GO TO 3.
NG © Repair harness or connector.
EL-126
NAVIGATION SYSTEM
All Images Are Not Displayed (Cont’d)
3. CHECK HARNESS
GI
1. Disconnect NAVI control unit and transfer unit connectors.
2. Check continuity between NAVI control unit harness connector (A) M180 terminals 69, 70 and transfer unit harness MA
connector (B) M173 terminals 11, 13.
69 - 11: Continuity should exist.
70 - 13: Continuity should exist. EM
3. Check continuity between NAVI control unit harness connector (A) M180 terminals 69, 70 and ground.
69, 70 - Ground: Continuity should not exist.
LC
EC
FE
CL
SKIB7020E
OK or NG MT
OK © GO TO 4.
AT
4. CHECK NAVI CONTROL UNIT AND TRANSFER UNIT
TF
1. Replace NAVI control unit or transfer unit.
3. Check if an image is displayed on the screen. PD
Is an image displayed on the screen?
YES © INSPECTION END
NO © Replace the other unit.
FA
RA
BR
ST
RS
BT
HA
SE
IDX
EL-127
NAVIGATION SYSTEM
5. CHECK POWER SUPPLY CIRCUIT
Check voltage between the following harness connector terminals and ground.
SKIB7021E
Terminals
Unit (+) OFF ACC ON
(-)
Connector Terminal
(A) NAVI switch M169 1 0V Battery voltage Battery voltage
21, 23 Battery voltage Battery voltage Battery voltage
(B) Display M170
19 Ground 0V Battery voltage Battery voltage
31, 32 Battery voltage Battery voltage Battery voltage
(C) Transfer unit M173
29 0V Battery voltage Battery voltage
OK or NG
OK © GO TO 6.
EL-128
NAVIGATION SYSTEM
6. CHECK GROUND CIRCUIT
GI
2. Disconnect NAVI switch, display and transfer unit connectors. MA
3. Check continuity between the following harness connector terminals and ground.
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
SKIB7022E
ST
Terminals
Unit (+)
(-)
Continuity RS
Connector Terminal
(A) NAVI switch M169 7
(B) Display M170 22, 24 Ground Yes
(C) Transfer unit M173 25, 27
BT
HA
OK or NG
OK © GO TO 7.
SE
IDX
EL-129
NAVIGATION SYSTEM
7. CHECK HARNESS
1. Check continuity between transfer unit harness connector (A) M173 terminal 20 and display harness connector (B)
M170 terminal 16.
2. Check continuity between transfer unit harness connector (A) M173 terminal 20 and ground.
20 - Ground: Continuity should not exist.
SKIB7023E
OK or NG
OK © GO TO 8.
8. CHECK COMMUNICATION SIGNAL (NAVI-DISP)

1. Connect NAVI switch, display and transfer unit connectors.
3. Check voltage waveform between transfer unit harness connector M173 terminal 20 and ground using CONSULT-ll or
oscilloscope.
20 - Ground:
SKIB3607E
SKIB7024E
OK or NG
OK © GO TO 9.
NG © Replace transfer unit.
EL-130
NAVIGATION SYSTEM
9. CHECK HARNESS
GI
2. Disconnect display and NAVI switch connectors. MA
3. Check continuity between display harness connector (A) M170 terminal 15 and NAVI switch harness connector (B)
M169 terminal 4.
4. Check continuity between display harness connector (A) M170 terminal 15 and ground.
LC
EC
FE
CL
SKIB7025E
OK or NG MT
OK © GO TO 10.
AT
10. CHECK COMMUNICATION SIGNAL (DISP-SW)
TF
1. Connect display and NAVI switch connectors.
3. Check voltage waveform between display harness connector M170 terminal 15 and ground using CONSULT-ll or oscil- PD
loscope.
15 - Ground:
FA
RA
SKIB3606E BR
ST
RS
BT
SKIB7026E HA
OK or NG
OK © GO TO 11.
NG © Replace display.
SE
IDX
EL-131
NAVIGATION SYSTEM
11. CHECK HARNESS
2. Disconnect NAVI switch and transfer unit connectors.
3. Check continuity between NAVI switch harness connector (A) M169 terminal 5 and transfer unit harness connector (B)
M173 terminal 18.
4. Check continuity between NAVI switch harness connector (A) M169 terminal 5 and ground.
SKIB7027E
OK or NG
OK © GO TO 12.
12. CHECK COMMUNICATION SIGNAL (SW-NAVI)

1. Connect NAVI switch and transfer unit connectors.
3. Check voltage waveform between NAVI switch harness connector M169 terminal 5 and ground using CONSULT-ll or
oscilloscope.
5 - Ground:
SKIB3611E
SKIB7028E
OK or NG
OK © GO TO 13.
NG © Replace NAVI switch.
EL-132
NAVIGATION SYSTEM
13. CHECK HARNESS
GI
2. Disconnect NAVI control unit and display connectors. MA
3. Check continuity between NAVI control unit harness connector (A) M180 terminal 50 and display harness connector (B)
M170 terminal 8.
4. Check continuity between NAVI control unit harness connector (A) M180 terminal 50 and ground.
LC
EC
FE
CL
SKIB6983E
OK or NG MT
OK © GO TO 14.
AT
14. CHECK RGB AREA (YS) SIGNAL
TF
1. Connect NAVI control unit and display connectors.
3. Check voltage waveform between NAVI control unit harness connector M180 terminal 50 and ground using CON- PD
SULT-ll or oscilloscope.
FA
RA
BR
ST
SKIB6984E
RS
Terminal
Condition Reference value
(+) (-)
50 Ground When displaying RGB image Approx. 5 V BT
OK or NG HA
OK © Replace display.
NG © Replace NAVI control unit.
SE
IDX
EL-133
NAVIGATION SYSTEM
Vehicle Mark Is Not Displayed Properly

Symptom: Vehicle mark is not displayed at the vehicle driving position properly.
1. NAVIGATION SYSTEM ADJUSTMENT
1. Select “Navigation” in Confirmation/Adjustment mode, and adjust items, “Steering Angle Adjustment” and “Speed Cali-
bration”.
2. Check symptom with driving.
Is any malfunction observed?
YES © GO TO 2.
NO © INSPECTION END
2. SELF-DIAGNOSIS
Start self-diagnosis, and check any malfunction related to GPS.
Is any malfunction related to GPS observed?
YES © Repair malfunctioning part by diagnostic results.
NO © GO TO 3.
3. CHECK VEHICLE SIGNAL

Select “Vehicle Signals” in Confirmation/Adjustment mode, and check the vehicle speed signal and reverse signal inputting
to NAVI control unit.
OK or NG
OK © Limit of position detection capacity.
NG © I Check NAVI control unit vehicle speed signal circuit, and repair malfunctioning part.
I Check NAVI control unit reverse signal circuit, and repair malfunctioning part.
EL-134
NAVIGATION SYSTEM
Tint Is Strange for The RGB Image GI

Symptom: Tint of RGB image is strange.
1. CHECK HARNESS MA
2. Disconnect NAVI control unit and display connectors. EM
3. Check the malfunctioning circuit according to the symptoms.
I Light blue (Cyan) tinged screen
Check continuity between NAVI control unit harness connector (A) LC
M180 terminal 44 and display harness connector (B) M170 terminal 1.
Check continuity between NAVI control unit harness connector (A) EC
M180 terminal 44 and ground.
FE
CL
SKIB6994E
I Purple (Magenta) tinged screen
Check continuity between NAVI control unit harness connector (A) MT
Check continuity between NAVI control unit harness connector (A) AT
TF
PD
SKIB6995E
I Yellow tinged screen FA
Check continuity between NAVI control unit harness connector (A)
46 - 3: Continuity should exist. RA
Check continuity between NAVI control unit harness connector (A)
46 - Ground: Continuity should not exist. BR
ST
SKIB6996E
OK or NG RS
OK © GO TO 2.
NG © Repair harness or connector. BT
HA
SE
IDX
EL-135
NAVIGATION SYSTEM
Tint Is Strange for The RGB Image (Cont’d)
2. CHECK RGB SIGNAL
3. Start Confirmation/Adjustment mode.
4. Display color bar by selecting “Color Spectrum bar” on Display Diagnosis screen.
5. Check the malfunctioning circuit according to the symptoms.
I Light blue (Cyan) tinged screen
Check voltage waveform between NAVI control unit harness connector
M180 terminal 44 and ground using CONSULT-ll or oscilloscope.
44 - Ground:
SKIB7360E
SKIB6997E
I Purple (Magenta) tinged screen

45 - Ground:
SKIB7361E
SKIB6998E
I Yellow tinged screen

46 - Ground:
SKIB7362E
SKIB6999E
OK or NG
EL-136
NAVIGATION SYSTEM
RGB Image Is Rolling GI

Symptom: RGB image such as a map screen is rolling.
1. CHECK HARNESS MA
2. Disconnect NAVI control unit and display connectors. EM
3. Check continuity between NAVI control unit harness connector (A) M180 terminal 48 and display harness connector (B)
M170 terminal 7.
48 - 7: Continuity should exist. LC
4. Check continuity between NAVI control unit harness connector (A) M180 terminal 48 and ground.
EC
FE
CL
MT
SKIB7000E
OK or NG AT
OK © GO TO 2.
TF
2. CHECK RGB SYNCHRONIZING SIGNAL
PD
3. When displaying RGB image, check voltage waveform between NAVI control unit harness connector M180 terminal 48
and ground using CONSULT-ll or oscilloscope.
FA
48 - Ground:
RA
BR
SKIB3603E ST
RS
BT
HA
SKIB7001E
OK or NG
SE
IDX
EL-137
NAVIGATION SYSTEM
Values for All Items in the Drive Computer

Screen Do Not Change
Symptom: Values for items, “Elapsed Time”, “Driving Distance” and “Average Speed” in the Drive Computer
screen do not change.
1. CHECK NAVI CONTROL UNIT IGNITION SIGNAL
Select “Vehicle Signals” in Confirmation/Adjustment mode, and check the ignition signal inputting to NAVI control unit.
OK or NG
OK © Replace NAVI control unit.
NG © Check NAVI control unit ignition signal circuit, and repair malfunctioning part.
Values for Items, “Driving Distance” and

“Average Speed” Do Not Change
Symptom: Values for Items, “Driving Distance” and “Average Speed” do not change. (The Value for “Elapsed
Time” Changes.)
1. CHECK NAVI CONTROL UNIT VEHICLE SPEED SIGNAL
Select “Vehicle Signals” in Confirmation/Adjustment mode, and check the vehicle speed signal inputting to NAVI control
unit.
OK or NG
OK © Replace NAVI control unit.
NG © Check NAVI control unit vehicle speed signal circuit, and repair malfunctioning part.
Voice Guidance Is Not Heard

Symptom: Voice guidance does not sound at route guidance.
1. CHECK CONDITION
Turn audio system ON, and check if any sound can be heard from front door speaker (driver side).
OK or NG
OK © GO TO 2.
NG © Repair malfunctioning part.
2. CHECK CONDITION
Turn audio system ON, and check if front door speaker (driver side) is muted when pressing “VOICE” button during sound-
ing from front door speaker (driver side).
Is front door speaker (driver side) muted?
YES © GO TO 3.
NO © GO TO 7.
EL-138
NAVIGATION SYSTEM
Voice Guidance Is Not Heard (Cont’d)
3. CHECK HARNESS
GI
2. Disconnect NAVI control unit and transfer unit connectors. MA
3. Check continuity between NAVI control unit harness connector (A) M179 terminals 12, 14 and transfer unit harness
connector (B) M173 terminals 8, 10.
4. Check continuity between NAVI control unit harness connector (A) M179 terminals 12, 14 and ground.
12, 14 - Ground: Continuity should not exist. LC
EC
FE
CL
SKIB7002E MT
OK or NG
OK © GO TO 4.
AT
4. CHECK VOICE GUIDANCE SIGNAL TF

1. Connect NAVI control unit and transfer unit connectors.
2. Turn ignition switch ON. PD
3. When pressing “VOICE” button, check voltage waveform between NAVI control unit harness connector M179 terminals
12 and 14 using CONSULT-ll or oscilloscope.
12 - 14:
FA
RA
BR
SKIB3597E
ST
RS
BT
HA
SKIB7003E
OK or NG
OK © GO TO 5.
SE
IDX
EL-139
NAVIGATION SYSTEM
5. CHECK HARNESS
2. Disconnect transfer unit and voice change relay connectors.
3. Check continuity between transfer unit harness connector (A) M173 terminals 1, 2 and voice change relay harness con-
nector (B) M174 terminals 6, 7.
4. Check continuity between transfer unit harness connector (A) M173 terminals 1, 2 and ground.
1, 2 - Ground: Continuity should not exist.
SKIB7004E
OK or NG
OK © GO TO 6.
6. CHECK VOICE GUIDANCE SIGNAL

1. Connect transfer unit and voice change relay connectors.
3. When pressing “VOICE” button, check voltage waveform between transfer unit harness connector M173 terminals 1
and 2 using CONSULT-ll or oscilloscope.
1 - 2:
SKIB3609E
SKIB7005E
OK or NG
OK © Replace voice change relay.
EL-140
NAVIGATION SYSTEM
7. CHECK HARNESS
GI
2. Disconnect transfer unit and voice change relay connectors. MA
3. Check continuity between transfer unit harness connector (A) M173 terminals 4, 6 and voice change relay harness con-
nector (B) M174 terminals 1, 2.
4. Check continuity between transfer unit harness connector (A) M173 terminal 6 and ground.
6 - Ground: Continuity should not exist. LC
EC
FE
CL
SKIB7006E MT
OK or NG
OK © GO TO 8.
AT
8. CHECK VOICE GUIDANCE ON SIGNAL TF

1. Connect transfer unit and voice change relay connectors.
2. Turn ignition switch ON. PD
3. When pressing “VOICE” button, check voltage waveform between transfer unit harness connector M173 terminals 6
and 4 using CONSULT-ll or oscilloscope.
6 - 4:
FA
RA
BR
SKIB3610E
ST
RS
BT
HA
SKIB7007E
OK or NG
OK © Replace voice change relay.
SE
IDX
EL-141
NAVIGATION SYSTEM
RDS-TMC (Traffic Information) Is Not Received

1. CHECK SELF-DIAGNOSIS
Perform self-diagnosis.
Is self-diagnosis result normal?
YES © GO TO 2.
NO © Refer to EL-117.
2. CHECK CONDITION
Turn ignition switch ON, and audio unit ON.
Does audio unit receive radiobroadcast?
YES © Replace TMC tuner.
NO © Check antenna and antenna feeder.
EL-142
NAVIGATION SYSTEM
Example of Symptoms Judged Not Malfunction GI
BASIC OPERATIONS MA
Symptom Possible cause Remedy
No image comes on.

The brightness adjustment is at the lowest
Adjust to brighter setting.
EM
setting.
No map DVD-ROM is inserted, or it is
Insert the DVD-ROM correctly.
No map comes on the screen. inserted upside down. LC
The map display mode is switched off. Press the “MAP” button.
No voice guidance is available. or The volume is not set correctly or it is turned
The volume is not high enough. off.
Adjust the volume correctly. EC
The screen is too dim. The move-
The temperature in the vehicle is low. Wait for the temperature to rise.
ment is slow.
FE
There are darker or brighter dots in
It is inherent to LC displays. This is not malfunction.
the display.
CL
VEHICLE MARKS
This is because the displayed information is
MT
reduced so that the screen does not become
too crowded. There is also a chance that
The location names differ between
PLAN VIEW and BIRDVIEW.
names of the roads or locations will be It should not be regarded as malfunction. AT
repeatedly displayed. The name appearing
on the screen may be different because of
the processing procedure.
TF
The vehicle might have moved with the igni-
The vehicle mark is not shown cor- Drive the vehicle with GPS on for some dis-
tion off, for example on a ferry boat or car
rectly. tance.
transporter.
PD
The screen does not switch to night Turn the headlights on again, go to DISPLAY
The last time the lights were turned on, your
mode even after turning the head- SETTINGS screen and set it to the night
setting was in daytime mode.
lights on. mode.
The map does not scroll even when The display is not switched to the map
FA
Press the “MAP” button.
the vehicle is traveling. screen.
The display is not switched to the map
The vehicle mark does not show up.
screen.
Press the “MAP” button. RA
GPS signals are not received because the
Move the vehicle outdoors with a clear view
vehicle is indoors or in the shade of build-
GPS indicator on the screen remains ings. of the sky. BR
gray.
Wait for the satellites to move to better loca-
GPS satellites are in poor locations.
tions.
ST
If the vehicle mark does not move to the cor-
Driving on slippery road surface rect position even after the vehicle has been
driven for approximately 10 km (6 miles),
Driving on slanted area adjust the current location. If necessary, RS
adjust the moving speed of the vehicle.
If the position maker does not move to the
Rough or violent driving.
correct position even after the vehicle has BT
been driven for approximately 10 km (6
miles), adjust the current location.
The location of the vehicle mark
does not match the actual position.
GPS indicator remains gray.
Please check the GPS indicator on the HA
screen to see if it remains gray.
Errors (gain or loss) result in calculating the It will move by driving the vehicle for 30 min-
speed from the speed pulse because the utes [in case it is running at 30 km/h (19
vehicle has tire chains on, or the system was MPH)]. If you still notice errors, adjust moving
transferred to a different vehicle. speed.
The map data has an error or is incomplete SE
(if the location error always happens in the Please wait for the updated Map.
same area).
IDX
EL-143
NAVIGATION SYSTEM
Example of Symptoms Judged Not Malfunction
(Cont’d)
MAP DVD-ROM
Check the DVD-ROM and wipe it clean with
The message “Error” appears after Map DVD-ROM is soiled or partially dam- a soft cloth.
operation. aged. In case you see any damage, replace the
DVD-ROM.
DESTINATION, WAYPOINTS OR MENU CONTENTS CANNOT BE CHOSEN OR SET

Route calculation has not yet been Set the destination and request route calcula-
requested. tion.
Turn list is not displayed. The vehicle mark is not on the suggested Please drive the vehicle along the suggested
route. route.
Route guidance is off. Turn the route guidance on.
In re-routing, the waypoints are not The system has judged that the vehicle has If you want to go to that point again, edit the
included in the calculation. already passed the point. route again.
Route calculation has not yet been Set the destination and request route calcula-
requested. tion.
Route information is not displayed. The vehicle mark is not on the suggested Please drive the vehicle along the suggested
route. route.
Route guidance is off. Turn the route guidance on.
Enter the route that can be calculated from.
The vehicle is not running on a route that can Alternatively, you can calculate the route
Route is not calculated automatically.
be calculated from. manually. In this case, the entire route will be
calculated again.
Your vehicle is not running on the suggested Restart route calculation or join the sug-
It is impossible to request a detour.
route. gested route.
The system took many conditions into
The detour found is the same as the
consideration, but the same result was This is not malfunction.
previous suggestion.
obtained.
It is impossible to set more than 5 waypoints.
It is impossible to set the waypoints. The number of waypoints exceeds 5.
Please divide them in groups to find them all.
VOICE GUIDANCE
Voice guidance is only available at certain
intersections marked with . In some cases,
System is not malfunction.
the guidance is not available even when the
vehicle should make a turn.
The voice guidance is not available. Return to the recommended route or
The vehicle is off the suggested route.
re-search the route.
Voice guidance is set off. Turn the voice guidance on.
Route guidance is set off. Turn the route guidance on.
The content of the voice guidance may vary,
The guidance content does not cor-
depending on the types of junctions to make Follow the actual rules and regulations.
respond to the actual condition.
turns on.
EL-144
NAVIGATION SYSTEM
Example of Symptoms Judged Not Malfunction
(Cont’d) GI
ROUTE CALCULATION
Symptom Possible cause Remedy MA
Although the system is set with the
moving direction as the preference, it
There is no route found in that direction. This is not malfunction.
does not find the route by matching EM
the preference.
Reset the destination close to the road dis-
played with orange, or wider ones. Especially LC
There is no road close to the destination that with roads which have separate lanes for
can be found by this system. opposite directions, be careful in setting the
Route is not indicated. destination or waypoints on it, as results may
differ depending on the lane you choose. EC
The starting point to the destination is too
Set more distant destinations.
close.
The route is not displayed continu-
FE
Suggested routes may be displayed discon-
ously at waypoints that are for
tinuously near waypoints as route calculation This is not malfunction.
example not calculated routes from
is done at each waypoint.
the vehicle’s current position. CL
Suggested routes are stored in memory by
The suggested route the vehicle has
the blocks; if the vehicle travels past way- This is not malfunction.
travelled is erased.
point 1, the former data will be erased. MT
If there are restrictions (such as one-way traf-
fic) on roads close to the starting point or Try slightly moving the starting point or desti-
A very detoured route is suggested.
destination, the system may suggest a nation. AT
detoured route.
The landmark description does not It may be caused by insufficient or incorrect
Please wait for the update Map DVD-ROM.
correspond to the actual one. data on the DVD-ROM. TF
Set these points on the main road displayed
The suggested route does not
There is no data for route calculation closer in thick orange. Please note that in some
exactly connect to the starting point,
to these points. cases even main roads lack the data for PD
waypoints, or destination.
route calculation.
NOTE: FA
Except for the ordinance-designated cities and the prefectural capitals. (Applicable areas may be changed in
the updated map disc.)
RA
BR
ST
RS
BT
HA
SE
IDX
EL-145
HEATED SEAT/WAGON AND HARDTOP MODELS
Wiring Diagram — HSEAT —
TEL241N
EL-146
HEATED SEAT/WAGON AND HARDTOP MODELS
Wiring Diagram — HSEAT — (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL671A
IDX
EL-147
AUTOMATIC SPEED CONTROL DEVICE (ASCD)/WAGON AND HARDTOP
MODELS
Schematic
TEL242N
EL-148
MODELS
Wiring Diagram — ASCD — GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL569M IDX
EL-149
MODELS
Wiring Diagram — ASCD — (Cont’d)
TEL243N
EL-150
MODELS
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL244N
IDX
EL-151
MODELS
TEL090N
EL-152
POWER WINDOW/WAGON AND HARDTOP MODELS
Schematic GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL245N IDX
EL-153
Wiring Diagram — WINDOW —
TEL246N
EL-154
Wiring Diagram — WINDOW — (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL092N
IDX
EL-155
TEL093N
EL-156
LHD WAGON MODELS GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL094N
IDX
EL-157
RHD WAGON MODELS
TEL095N
EL-158
POWER DOOR LOCK/WAGON AND HARDTOP MODELS
Schematic/With Theft Warning System Models GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL573M IDX
EL-159
Wiring Diagram — D/LOCK —/RHD Models

With Theft Warning System
TEL269N
EL-160
With Theft Warning System (Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL270N
IDX
EL-161
With Theft Warning System (Cont’d)
TEL271N
EL-162
With Theft Warning System (Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL272N
IDX
EL-163
Schematic/Without Theft Warning System

Models
TEL096N
EL-164
Wiring Diagram — D/LOCK —/Without Theft GI

Warning System Models
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
TEL327N
EL-165
Wiring Diagram — D/LOCK —/Without Theft
Warning System Models (Cont’d)
TEL328N
EL-166
Warning System Models (Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL329N
IDX
EL-167
Warning System Models (Cont’d)
TEL330N
EL-168
MULTI-REMOTE CONTROL SYSTEM/WAGON AND HARDTOP MODELS
Wiring Diagram — MULTI —/For Australia GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL331N IDX
EL-169
MULTI-REMOTE CONTROL SYSTEM/WAGON AND HARDTOP MODELS
Wiring Diagram — MULTI —/For Australia
(Cont’d)
TEL332N
EL-170
THEFT WARNING SYSTEM/WAGON AND HARDTOP MODELS
Schematic GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL122N IDX
EL-171
Wiring Diagram — THEFT —/LHD Models
TEL123N
EL-172
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL124N
IDX
EL-173
(Cont’d)
TEL726M
EL-174
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL273N
IDX
EL-175
(Cont’d)
TEL126N
EL-176
Wiring Diagram — THEFT —/RHD Models GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL127N IDX
EL-177
Wiring Diagram — THEFT —/RHD Models
(Cont’d)
TEL274N
EL-178
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL129N
IDX
EL-179
(Cont’d)
TEL275N
EL-180
(Cont’d) GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL130N
IDX
EL-181
CAN SYSTEM/TB48 ENGINE MODELS WITH A/T
Wiring Diagram — CAN —
TEL247N
EL-182
HARNESS LAYOUT
How to Read Harness Layout GI
Example: MA
G2 E1 B/6 : ASCD ACTUATOR
EM
Connector color / Cavity
Connector number
LC
Grid reference
The following Harness Layouts use a map style grid to help locate connectors on the drawings: EC
I Main Harness
I Engine Room Harness
I Body Harness FE
To use the grid reference

CL
1) Find the desired connector number on the connector list.
2) Find the grid reference.
3) On the drawing, find the crossing of the grid reference letter column and number row. MT
4) Find the connector number in the crossing zone.
5) Follow the line (if used) to the connector.
AT
CONNECTOR SYMBOL
Main symbols of connector (in Harness Layout) are indicated in the below.
TF
Water proof type Standard type
Connector type
Male Female Male Female
PD
I Cavity: Less than 4
I Relay connector
I Cavity: From 5 to 8 FA
I Cavity: More than 9 RA

— —
I Ground terminal etc.

—
BR
ST
RS
BT
HA
SE
IDX
EL-183
HARNESS LAYOUT/WAGON AND HARDTOP MODELS
Main Harness/LHD Models
TEL151V
EL-184
Main Harness/LHD Models (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL126V
IDX
EL-185
Main Harness/LHD Models (Cont’d)
TEL152V
EL-186
NOTE
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
EL-187
Main Harness/RHD Models
TEL184V
EL-188
Main Harness/RHD Models (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL185V
IDX
EL-189
TEL186V
EL-190
NOTE
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
EL-191
Engine Room Harness/LHD Models

DIESEL ENGINE MODELS
TEL154V
EL-192
Engine Room Harness/LHD Models (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL155V
IDX
EL-193
PASSENGER COMPARTMENT
TEL156V
EL-194
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL157V
IDX
EL-195
Engine Room Harness/RHD Models

GASOLINE ENGINE MODELS
TEL187V
EL-196
Engine Room Harness/RHD Models (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL188V
IDX
EL-197
PASSENGER COMPARTMENT
TEL133V
EL-198
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL134V
IDX
EL-199
Engine Harness
TB48DE ENGINE
TEL189V
EL-200
Engine Harness (Cont’d)
ZD ENGINE GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL147V
IDX
EL-201
Engine Control Harness

TB48DE ENGINE
TEL190V
EL-202
Engine Control Harness (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL191V
IDX
EL-203
Body Harness/LHD Models

WAGON
TEL158V
EL-204
Body Harness/LHD Models (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL159V
IDX
EL-205
Body Harness/RHD Models

WAGON
TEL160V
EL-206
Body Harness/RHD Models (Cont’d)
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL137V
IDX
EL-207
HARDTOP
TEL161V
EL-208
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL139V
IDX
EL-209
Body No. 2 Harness/LHD Models

WAGON
TEL162V
EL-210
Body No. 2 Harness/LHD Models (Cont’d)
HARDTOP GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL163V
IDX
EL-211
Body No. 2 Harness/RHD Models

WAGON
TEL164V
EL-212
Body No. 2 Harness/RHD Models (Cont’d)
HARDTOP GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL165V
IDX
EL-213
Room Lamp Harness
TEL166V
EL-214
NOTE
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
IDX
EL-215
HARNESS LAYOUT/PICKUP MODELS
Main Harness/RHD Models

INSTRUMENT PANEL
TEL177V
EL-216
HARNESS LAYOUT/PICKUP MODELS
GI
MA
EM
LC
EC
FE
CL
MT
AT
TF
PD
FA
RA
BR
ST
RS
BT
HA
SE
TEL178V
IDX
EL-217

Electrical Wiring Sceme Nissan Patrol

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Electrical Wiring Sceme Nissan Patrol

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electrical Wiring Sceme Nissan Patrol

Uploaded by

Copyright:

Available Formats

Go to SUP8 1st Rev.

POWER SUPPLY ROUTING/WAGON AND Wiring Diagram - WARN - .........................................62 MT

Wiring Diagram — POWER —

Wiring Diagram — POWER — GI

Wiring Diagram — START —/A/T Models with

Wiring Diagram — START —/A/T Models with GI

Wiring Diagram — DTRL —

Wiring Diagram — TURN —/Type A GI

Wiring Diagram — TURN —/Type B

Wiring Diagram — TURN —/Type D

Wiring Diagram — ILL — GI

Wiring Diagram — METER — GI

Wiring Diagram — WARN —

Wiring Diagram — WARN —

Wiring Diagram — AT/IND —/TB48 Engine GI

Wiring Diagram — WIP/R —

Wiring Diagram — CIGAR —/RHD Models

Wiring Diagram — DEF —/LHD Models GI

Schematic/LHD Models with Sub-harness GI

Wiring Diagram — AUDIO —/LHD Models with

Schematic/RHD Models with Sub-harness GI

Wiring Diagram — AUDIO —/RHD Models with

Schematic/LHD Models without Sub-harness GI

Wiring Diagram — AUDIO —/LHD Models

Schematic/RHD Models without Sub-harness

Wiring Diagram — AUDIO —/RHD Models GI

Traffic Information (RDS-TMC) GI

Wiring Diagram — NAVI —/LHD Models GI

Wiring Diagram — NAVI —/RHD Models

Terminals and Reference Value for NAVI GI

Select “Color bar” of AT

RGB area RGB screen is not

Vehicle When vehicle speed Navigation current-loca-

Terminals and Reference Value for Display GI

Select “Color bar” of FE

Terminals and Reference Value for NAVI Switch

Terminals and Reference Value for Transfer

Only route guidance and

Only route guidance and

25 (B) Ground Ground — ON — Approx. 0 V — BT

Terminals and Reference Value for TMC Tuner

Terminals and Reference Value for Voice GI

Only route guidance and FA

*1: LHD models.

Special Note for Trouble Diagnosis

Self Diagnosis Mode GI

3. The initial trouble diagnosis screen will be shown, and items EC

Quick Reference Table MA

NAVI control unit malfunction is

1. Check if GPS antenna feeder line

3. The initial trouble diagnosis screen will be shown, and items EC

Diagnosis item Display Condition Remarks

DVD-ROM Seek Error

FEATURE RESTRICTION SETTING EC

All Images Are Not Displayed

2. CHECK NAVI CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

2. Turn ignition switch OFF.