ES_LPC177x/8x

Errata sheet LPC177x/8x

Rev. 2 1 September 2011 Errata sheet

Document information Info Keywords Content LPC1788FBD208, LPC1788FET208, LPC1788FET180, LPC1788FBD144, LPC1787FBD208, LPC1786FBD208, LPC1785FBD208, LPC1778FBD208, LPC1778FET208, LPC1778FET180, LPC1778FBD144, LPC1777FBD208, LPC1776FBD208, LPC1776FET180, LPC1774FBD208, LPC1774FBD144, LPC177x/8x errata This errata sheet describes both the known functional problems and any deviations from the electrical specifications known at the release date of this document. Each deviation is assigned a number and its history is tracked in a table at the end of the document.

Abstract

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

Revision history Rev 2 Date 20110901 Description

1.1

20110601

20110525

Added ISP.1. Added Rev A. Added WDT.1. Added DPD.1. Added USART. Initial version.

Contact information
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected]
ES_LPC177X_8X All information provided in this document is subject to legal disclaimers. NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

2 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

1. Product identification
The LPC177x/8x devices typically have the following top-side marking: LPC17xxXXX xxxxxxx xxYYWWR[x] The last digit in the last line (field R) will identify the device revision. Note: Pre-production parts are marked differently and this system does not apply. This Errata Sheet covers the following revisions of the LPC177x/8x:
Table 1. - A Device revision table Revision description Initial device revision Second device revision

Revision identifier (R)

Field YY states the year the device was manufactured. Field WW states the week the device was manufactured during that year.

2. Errata overview
Table 2. Functional problems ADC.1 ISP.1 RTC.1 USART.1 USART.2 USB.1 WDT.1 Table 3. AC/DC deviations DPD.1 Functional problems table Short description External sync inputs not operational Maximum UART ISP baud rate limited to 57,600 The RTC may lose time when RESET is toggled Smart Card TX retry error interrupt not working False positive break indicator events may occur USB host controller hangs on a dribble bit WDT timeout does not wake from deep sleep AC/DC deviations table Short description Increase of Deep power-down leakage current over time Errata notes table Short description n/a Revision identifier n/a Detailed description n/a Revision identifier - Detailed description Section 4.1 Revision identifier -, A -, A -, A -, A -, A -, A -, A Detailed description Section 3.1 Section 3.2 Section 3.3 Section 3.4 Section 3.5 Section 3.6 Section 3.7

Table 4. n/a

Errata notes

ES_LPC177X_8X

All information provided in this document is subject to legal disclaimers.

NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

3 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

3. Functional problems detail

3.1 ADC.1: External sync inputs not operational
Introduction: In software-controlled mode (BURST bit is 0), the 10-bit ADC can start conversion by using the following options in the A/D Control Register:

Fig 1.

A/D control register options

Problem: The external start conversion feature, AD0CR:START = 0x2 or 0x3, may not work reliably and ADC external trigger edges on P2.10 or P1.27 may be missed. The occurrence of this problem is peripheral clock (PCLK) dependent. The probability of error (missing a ADC trigger from GPIO) is estimated as follows:

For PCLK = 100 MHz, probability error = 12 % For PCLK = 50 MHz, probability error = 6 % For PCLK = 12 MHz, probability error = 1.5 %
The probability of error is not affected by the frequency of ADC start conversion edges. Work-around: In software-controlled mode (BURST bit is 0), the START conversion options (bits 26:24 set to 0x1 or 0x4 or 0x5 or 0x6 or 0x7) can be used. The user can also start a conversion by connecting an external trigger signal to a capture input pin (CAPx) from a Timer peripheral to generate an interrupt. The timer interrupt routine can then start the ADC conversion by setting the START bits (26:24) to 0x1. The trigger can also be generated from a timer match register.
ES_LPC177X_8X All information provided in this document is subject to legal disclaimers. NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

4 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

3.2 ISP.1: Maximum UART ISP baud rate limited to 57,600

Introduction: In-System Programming (ISP) is programming or reprogramming the on-chip flash memory, using the boot loader software and UART0 serial port. This can be done when the part resides in the end-user board. Problem: UART ISP cannot be used at rates higher than 57,600 bits per second. Work-around: UART ISP must be used at 57,600 bits per second or a lower communications speed.

3.3 RTC.1: RTC may lose time when RESET is toggled

Introduction: The Real Time Clock (RTC) is a set of counters for measuring time when system power is on, and optionally when it is off. It uses very little power when its registers are not being accessed by the CPU, especially in reduced power modes. Problem: RTC temporarily pauses and loses fractions of a second during the rising and falling edges of RESET. This occurs only in the LQFP packages with certain voltage swings and ramp rates. The problem is exacerbated by low temperatures. Reducing the voltage swing and/or ramp rate of the reset pulse will eliminate this loss of time counts. When this issue occurs, the impact on RTC accuracy is expected to be one second every several thousand reset events. Work-around: Adding an RC filter between the reset pin and the external reset input to control the reset signal voltage ramp rate can prevent this problem.

LPC1788 RESET pin 10KO 0.1F External RESET input

Fig 2.

RTC.1 work-around

ES_LPC177X_8X

All information provided in this document is subject to legal disclaimers.

NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

5 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

3.4 USART.1: Smart Card TX retry error interrupt not working

Introduction: USART4 includes a synchronous mode and a Smart Card mode supporting ISO 7816-3. This allows smart cards to be interfaced to support high security applications. Problem: The USART4 Transmit Interrupt is entered after failed retries (based on NACK) but source of error is not given in IIR or LSR registers. This happens when the TX FIFO has one or more items still to be sent out. When there are no other items in the TX FIFO and the FIFO head item fails the retry, the interrupt works correctly with bit 8 flagged in the LSR. Work-around: A workaround is to avoid using the FIFO on USART4 in Smart Card mode. When there is data ready to transmit, hold it in a software queue until the FIFO is empty then send it one character at a time. Another workaround is to check all of the interrupt sources in the TX interrupt and if there is no interrupt source, to assume that a NAK could have been received. This allows use of the FIFO but could require changes to program logic.

ES_LPC177X_8X

All information provided in this document is subject to legal disclaimers.

NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

6 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

3.5 USART.2: False positive break interrupt events may occur

Introduction: The LPC177x/8x device family features an option to operate the USART4 in synchronous mode. Problem: When using synchronous UART mode (USART) under the following conditions:

CSCEN = 0 (SCK active only during transmission) CSRC = 0 (Synchronous Slave Mode) FES = 1 (Falling Edge Sampling) SSDIS = 0 (Use Start and Stop Bit) The external transmitting device (Master) sends start and stop bits The external device transmits 0x00

The Break Interrupt (BI) flag can become set, despite the fact that no break condition on the bus has occurred. This problem does not manifest when the external master device uses two stop bits. Work-around: None, however in some cases system designers have control over the protocol being used between devices and can avoid the error condition outlined above in their system design and/or communication protocol.

ES_LPC177X_8X

All information provided in this document is subject to legal disclaimers.

NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

7 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

3.6 USB.1: USB host controller hangs on a dribble bit

Introduction: Full-/low-speed signaling uses bit stuffing throughout the packet without exception. If the receiver sees seven consecutive ones anywhere in the packet, then a bit stuffing error has occurred and the packet should be ignored. The time interval just before an EOP is a special case. The last data bit before the EOP can become stretched by hub switching skews. This is known as dribble and can lead to a situation where dribble introduces a sixth bit that does not require a bit stuff. Therefore, the receiver must accept a packet for which there are up to six full bit times at the port with no transitions prior to the EOP. Problem: The USB host controller will hang indefinitely if it sees a dribble bit on the USB bus. It will hang the first time a dribble bit is seen. Once it is in this state there is no recovery other than a hard chip reset. This problem has no effect on the USB device controller. Work-around: None.

ES_LPC177X_8X

All information provided in this document is subject to legal disclaimers.

NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

8 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

3.7 WDT.1: WDT timeout does not wake from deep sleep
Introduction: The purpose of the Watchdog Timer is to reset the microcontroller within a reasonable amount of time if it enters an erroneous state. When enabled, a watchdog event will be generated if the user program fails to "feed" (or reload) the Watchdog within a predetermined amount of time. The Watchdog event will cause a chip reset if configured to do so. Problem: WDT timeout operates in run and sleep modes, but does not wake the MCU from deep sleep mode. Work-around: None.

ES_LPC177X_8X

All information provided in this document is subject to legal disclaimers.

NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

9 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

4. AC/DC deviations detail

4.1 DPD.1: Increase of Deep power-down leakage current over time
Introduction: Deep power-down is a low-power mode that achieves currents in the low single-digit microamperes. Problem: Increase of IDDREG(3V3) current in Deep power-down mode for on-chip regulator over time (to about 100-200 uA). There is no functional impact. Expected time to result in high regulator Deep power-down current vs. temperature and bias is listed in Table 5.
Table 5. VDD 2.5 V 3.0 V 3.3 V LPC177x/8x on-chip regulator expected time (years) to result in high regulator Deep power-down current under different bias and temp condition Years at 25C 4.98E+05 714 14.1 Years at 85C 7190.00 10.30 0.20

Identification of Changed Product: All Rev - devices. Remarks: 1. Issue described will lead to problems only if customer puts bias on VDD_REG at over 3.0 V with application sensitive to IDDREG(3V3) curent in Deep power-down mode (few hundred uA) 2. If the biased VDD can be restricted to 3.0 V then the expected time to result in high leakage current will be over 10 years at Industrial temp range. 3. Biased VDD of 3.3 V at 25C (room temp) will also guarantee datasheet spec for over 10 years. 4. If IDDREG(3V3) current in Deep power-down mode (few hundred uA) is a key parameter, it is not advised to bias VDD_REG above 3.0 V. Work-around: None. This has been fixed in Rev A.

5. Errata notes detail

5.1 n/a

ES_LPC177X_8X

All information provided in this document is subject to legal disclaimers.

NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

10 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

6. Legal information
6.1 Definitions
malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customers own risk. Applications Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customers sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customers applications and products planned, as well as for the planned application and use of customers third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customers applications or products, or the application or use by customers third party customer(s). Customer is responsible for doing all necessary testing for the customers applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customers third party customer(s). NXP does not accept any liability in this respect. Export control This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities.

Draft The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information.

6.2

Disclaimers

Limited warranty and liability Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or

6.3

Trademarks

Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.

ES_LPC177X_8X

All information provided in this document is subject to legal disclaimers.

NXP B.V. 2011. All rights reserved.

Errata sheet

Rev. 2 1 September 2011

11 of 12

NXP Semiconductors

ES_LPC177x/8x
Errata sheet LPC177x/8x

7. Contents
1 2 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 4 4.1 5 5.1 6 6.1 6.2 6.3 7 Product identification . . . . . . . . . . . . . . . . . . . . 3 Errata overview . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional problems detail . . . . . . . . . . . . . . . . 4 ADC.1: External sync inputs not operational . . 4 ISP.1: Maximum UART ISP baud rate limited to 57,600. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 RTC.1: RTC may lose time when RESET is toggled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 USART.1: Smart Card TX retry error interrupt not working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 USART.2: False positive break interrupt events may occur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 USB.1: USB host controller hangs on a dribble bit 8 WDT.1: WDT timeout does not wake from deep sleep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 AC/DC deviations detail . . . . . . . . . . . . . . . . . 10 DPD.1: Increase of Deep power-down leakage current over time. . . . . . . . . . . . . . . . . . . . . . . 10 Errata notes detail . . . . . . . . . . . . . . . . . . . . . . 10 n/a. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Legal information. . . . . . . . . . . . . . . . . . . . . . . 11 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Please be aware that important notices concerning this document and the product(s) described herein, have been included in section Legal information.

NXP B.V. 2011.

All rights reserved.

For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 1 September 2011 Document identifier: ES_LPC177X_8X