Instruction Manual For Multi Head Drilling Machine LZD12-17

LZD12-17
Multi Head Drilling Machine
Instruction
Manual
DEMAC ENGINEERING CO., LIMITED
1
Content
1. Main functions ................................................................................................................ 3
2. Main Technical Parameter ...................................................................................... 3
3. Main Structure............................................................................................................... .3
4.Transportation…………………………………………………………………………..4
5. Installation and Adjustment .................................................................................. .4
6. Use and Operation ........................................................................................................ 5
7.Maintainance................................................................................................................... 11
8. Attached drawing ........................................................................................................ 11
2
I. Main functions:
LZD12-17 Multi-head Drilling machine is applies to drilling holes on aluminum and

curtain wall profiles with 12 drilling head, special for large volume production. The
operation section is Max. Z: 200×250mm, Maxi. X length in 8000mm, and Max Y
length 250mm.And more important is the machine can be made to one or more head
according to the customer’s requirement, the head can be moved by hand, It’s very
convenience operation machines.
II. Main Technical parameter
1、Power： 3phase 600V 60hz

2、Motor power： 12×1.1KW
3、Working pressure： 0.6～0.8MPa
4、Air consumption： 200L/min
5、Rotation speed： 0-2800r/min Maxi.
6、Drilling Diameter Max.： 6-17 mm / 7mm
7、Max Drilling Distance in horizontal: 250mm
8、Max Drilling Distance in vertical: 250mm
9、Min distance between two holes: 22mm
10、Working table Dimension： 250×250mm
11、feeding travel： 125mm
12、Dimension: 8500×1200×1880mm
13、Weight： 3500kg
III. Main structure
1、Main characteristic
The clamping of this machine is used hydro-pneumatic damping cylinder and the
cylinder with switch used in parallel made feeding stable and the speed can be
adjustment, the appearance is better and easy for maintenance.
2、Main Configuration
The machine is made of drilling head, working table, feeding part of drilling
machine, clamping part and the electronic part.
The main working table (electronic controller) fit at the front of the machine, it can be
moved left or right, up and down.
3
Electric Box
Drill Head
Working
Table
Clamps
Control Panel
Distance adjustment
IV. Transportation
The machine should be prevent of jolt, slip and fall over when transportation. The
guide should add lubricant, a plastic cover in case of dust and rust if it has no use for a
long time.
V. Installation and Adjustment
1、Environment requirement
The machine should be installed in a dry, no dust, no corrosive gas, the in-temperature
of 10-40℃ concrete floor.
2、Opening package
Before installation, the machine should be removed with steel chassis to the place.
3、Put the level gauge on the working table, adjust base of the machine then tighten
the screw.
4、The machine must be grounded, the electronic line should be a green-yellow
combination insulated copper wire, which section is more than 2.5mm²，the
resistance is less than 4Ω.
5、Power: the requirement of power is 3phase 600volt 60hz 4 Lines
6、Putting gas source on the pneumatic controller, then adjust it to 0.6-0.8Mpa after
check no air leakage. Suggested to be 0.8 Mpa
4
VI. Use and Operation
1、Adjustment before operation

The feeding speed of drilling head can be adjusted by button of feeding cylinder, and
travelling can be adjustment by magnetive button of cylinder.
2、Operation
E STOP
Motor ON/OFF
Clamps
Feeding
5
Operation under Union Action：
Switch the button to “Union” on the

heads that will work in Union operation.
Press “Clamp” Button
Press “Feeding” Button
Motor working, should noted the

Rotation direction, if reverse, should
re-wiring the line U、V、W in correct
Cylinder start working, the drill head

feeding and return when touch the
limit sensor switch.
When drill head return and touch the

up limit switch, the motor will stop automatic
Clamp cylinder automatic loose
6
Operation under Single Action：
Switch the button to “Union” on the

head that will working
Operation is same as above Union

Action
Drill Head Moving Operation ：
Rotate the brake handle (under working table) to

anti-clockwise direction, the brake will loose off
and, and the Drill Head canbe moved in level
direction.
When the Drill Head upto the right

position, lock the brake handle in
clockwise direction
7
Brake
Handle
Brake Loose
Front/back moving operation：

1) Rotate the Handle Wheel to Clockwise
Direction
Drill head move to Front
2) Rotate the Handle Wheel to

Anti-Clockwise Direction
Drill head move to Back
8
Clockwise Direction
head moving to front。
Anti-Clockwise Direction
head moving to back
Vertical Adjustment Operation：
Rotate the Handle Wheel to Clockwise

1) Direction
Drill Head Rising up
Rotate the Handle Wheel to

2) Anti-Clockwise Direction
Drill Head Moving Down
9
1. Clockwise Direction
Head rising up。
2. Anti-Clockwise Direction
Head moving down
Drill bit operation on two type drill chuck : ：

1. By chuck, 6-17mm drill bit changeable
2. By Drill adapter 3 axis in line.
Drill bit with distance adjustment
10
In case of unusual circumstance, press the EMERGENCE button, the motor will be
off but the clamping cylinder is still on work, if you want it to release, you should
restart the motor on then press the button clamp/release.
VII. Maintenance
1、The vertical and horizontal guide should be lubricant frequently and keep it clean
after work..
2、Air source processor: filter traps should release the water, each clean weekly at
once, oil mist cups included the N20 lubricant or rust-turbine oil HU-(GB2537),
the oil level remains on the container height of 1/4 ~ 3/4 of the height of case,
lubricants normally last for 3 ~ 5 drop/min
3、Injection in every period for damping cylinder.
4、Keep the machine clean and lubricant regularly.
VIII. Attached drawing

PLC
Terminal
Replay
Breaker
Contactor
Frequency
11
12
13
14
15
16
17
18
19
20
21
DEMAC ENGINEERING CO., LIMITED
Yalin Industrial Park, Tianqiao Dist.
Jinan City 250033, China.
: 0086 531 8126 0880
www.demacengineering.com
[email protected]
22

Instruction Manual For Multi Head Drilling Machine LZD12-17

Uploaded by

Copyright:

Available Formats

Instruction Manual For Multi Head Drilling Machine LZD12-17

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Instruction Manual For Multi Head Drilling Machine LZD12-17

Uploaded by

Copyright:

Available Formats

LZD12-17

Multi Head Drilling Machine

DEMAC ENGINEERING CO., LIMITED

2. Main Technical Parameter ...................................................................................... 3

5. Installation and Adjustment .................................................................................. .4

6. Use and Operation ........................................................................................................ 5

8. Attached drawing ........................................................................................................ 11

LZD12-17 Multi-head Drilling machine is applies to drilling holes on aluminum and

II. Main Technical parameter

1、Power： 3phase 600V 60hz

III. Main structure

V. Installation and Adjustment

1、Adjustment before operation

Switch the button to “Union” on the

Press “Clamp” Button

Press “Feeding” Button

Motor working, should noted the

Cylinder start working, the drill head

When drill head return and touch the

Clamp cylinder automatic loose

Switch the button to “Union” on the

Operation is same as above Union

Drill Head Moving Operation ：

Rotate the brake handle (under working table) to

When the Drill Head upto the right

Front/back moving operation：

Drill head move to Front

2) Rotate the Handle Wheel to

Drill head move to Back

Vertical Adjustment Operation：

Rotate the Handle Wheel to Clockwise

Drill Head Rising up

Rotate the Handle Wheel to

Drill Head Moving Down

Drill bit operation on two type drill chuck : ：

2. By Drill adapter 3 axis in line.

Drill bit with distance adjustment

VIII. Attached drawing

You might also like