ECE204 Analog Circuit Design

This document provides information on the ECE204 Analog Circuit Design course, including objectives, expected outcomes, units of study, textbooks, and lab experiments. The objectives are to describe operational amplifiers and their characteristics, analyze and design op-amp circuits to perform analog computations and generate waveforms, describe 555 timers and PLL applications, and examine DAC and ADC circuits. The 7 units cover op-amp characteristics, linear op-amp circuits, op-amps with diodes, comparators, waveform generators, active filters, and PLLs and timers. The lab experiments involve designing circuits using op-amps and timers, including wave generators, filters, and precision rectifiers.

Uploaded by

connectvprakash

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

0% found this document useful (0 votes)

76 views2 pages

ECE204 Analog Circuit Design

Uploaded by

connectvprakash

We take content rights seriously. If you suspect this is your content, claim it here.

Available Formats

Download as PDF, TXT or read online on Scribd

You are on page 1/ 2

ECE204 Analog Circuit Design L T P C

3 0 2 4
Version No.: 1.10
Prerequisite: ECE207 Analog Electronic Circuits
Objectives:
Describe the Characteristics, frequency response and limitations of the operational amplifiers.
Analyze and design operational amplifier circuits to perform analog computations, switching
circuits, waveform generators and active filters.
Describe the operations of the 555 timers and PLLs and their applications.
Exhibit the characteristics of DAC and ADC circuits.
Expected Outcome:
1. Apply mathematical concepts to characterize and model the circuits using IC 741.
2. Design and troubleshoot simple analog circuits using Op amp, Timer ICs and PLLs.
3. List and discuss possible reasons for deviation between predicted and measured results from
an experiment or problems.
4. Construct A/D and D/A converters and study their characteristics.
Unit I Op-Amp Characteristics
Op-Amp equivalent circuits, terminals, ideal Op-Amp, Op-Amp DC characteristics: Low-
Frequency Model of Op-Amp, Non inverting Amplifier, Inverting Amplifier, bias, offset,
thermal drift, AC characteristics: Closed-Loop Frequency Response, Slew Rate, Combination of
Linear Noise in Operational Amplifier, Common Mode Rejection.

Unit II Linear Op- Amp Circuits

DC and AC amplifiers, summing, scaling, and averaging amplifiers, Instrumentation amplifiers,
I/V, V/I converter, Integrator, Differentiator, differential amplifiers. Op-amp with negative
feedback: voltage series, voltage shunt feedback amplifiers, Signal conditioning Circuits.

Unit III Op-Amps with Diodes

Logarithmic Amplifiers, Rectifiers, Peak DetSection and Voltage Regulation, LM 117/LM317
Regulators.
Unit IV Comparators and Waveform Generators
Comparator – zero crossing detector, schmitt trigger, free-running, one-shot Multivibrators, sine
wave generators- Barkhausen Criterion ,phase-shift, wein-bridge oscillators, Square/Triangular,
saw-tooth wave Function Generator.

Unit V Active Filters

Filter Classifications, Frequency and Impedance Scaling Butterworth Filter Responses Low-Pass
and High Pass Designs, Band-Pass Filter, Notch filter, All-pass filter.

Unit VI PLL and Timers

Phase detector comparator, VCO, Low-pass filter, monolithic PLL, PLL applications, operating
modes 555 timer, Astable and monostable operation and applications.

Unit VII A/D and D/A Converters

Sample-and-hold circuits, DAC characteristics, D/A conversion techniques, A/D characteristics,
A/D conversion techniques-integrating, successive approximation, flash converters.

Textbooks
1. R. A. Gayakwad, “Op-Amps and Linear Integrated Circuit”, 4/e Pearson Education, 2003.

Proceedings of the 29th Academic Council [26.4.2013] 314

2. D. Roy Choudhury, “Linear integrated Circuits”, New-Age International Publishers, 2002.

Reference Books
1. Robert F. Coughlin, and Driscoll,” Operational Amplifiers and Linear Integrated Circuits”, 6/e,
Pearson Education 2001.
2. P. R. Gray and R. G. Meyer,” Analysis and Design of Analog Integrated Circuit, John Wiley, 2003.

Mode of Evaluation: CAT- I & II, Quizzes, Assignments/ other tests, Term End Examination.