Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.

1 P 1 of 21

Displaytech Ltd.

Website: www.displaytech.com.hk

LCD Module
Product Specification

Product: 64128L Series LCD Module (128 x 64 DOTS)

Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 2 of 21

PRODUCT SPECIFICATIONS

GENERAL SPECIFICATION

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

ELECTRO-OPTICAL CHARACTERISTICS

BLOCK DIAGRAM

MECHANICAL DRAWING

BACKLIGHT DRAWING

BACKLIGHT SPECIFICATION

QUALITY GUARANTEE

PRECAUTIONS FOR USING LCD MODULES

USING LCD MODULES

REVISION RECORD

Contents in this document are subject to change without notice. No part of this document may be
reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose,
without the express written permission of Displaytech Ltd.

10 June 2008.
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 3 of 21

GENERAL SPECIFICATION
Item Contents
Display Format 128 x 64 DOTS
Dot Size (W x H) 0.40mm x 0.40mm
View Area (W x H) 60.60mm x 33.10mm
Module Size (W x H x T) 68.80mm x 49.20mm x 8.50mm
LCD Type FSTN
Polarizer Mode Transflective
View Angle 6 o’clock / 12 o’clock
Backlight LED
Backlight Driver Type External Power
Backlight Color White
Controller & LCD Driver ST7565R-G
Driving Method 1/65 Duty, 1/9 Bias

ABSOLUTE MAXIMUN RATINGS (Ta=25°°C VSS=0V)

ITEM SYMBOL MIN. TYP. MAX. UNIT
Power Supply for Logic VDD-VSS -0.3 --- 3.6 V
Power Supply for LCD V0-VSS -0.3 --- 13.5 V
Input Voltage VIN -0.3 --- VDD+0.3 V
Supply Voltage for LED Backlight VLED --- 3.2 --- V
Normal Operating Temperature Top 0 --- 50 °C
Normal Storage Temperature Tst -10 --- 60 °C
Wide Operating Temperature Top -20 --- 70 °C
Wide Storage Temperature Tst -30 --- 80 °C

ELECTRICAL CHARACTERISTICS (Ta=25°°C, VDD=3.0V)

ITEM SYMBOL CONDITION MIN. TYP. MAX. UNIT
Power Supply for LCM VDD-VSS --- 2.85 3.0 3.15 Volt
VIL L level Vss --- 0.2VDD Volt
Input Voltage
VIH H level 0.8VDD --- VDD Volt
--- --- --- ---
LCD Module Driving
VO-VSS 25°C --- 9.0 --- Volt
Voltage
--- --- --- ---
IDD VDD=3.0V --- 0.5 ---
Supply Current for
Ie --- --- --- --- mA
LCM
ILED VLED=3.2V --- 60 ---
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 4 of 21

ELECTRO-OPTICAL CHARACTERISTICS
Measuring STD.Value
NO Item Symbol Unit Remark
Condition °C Min Typ Max
Recommended θ=0
1 Operating VLCD Φ= 0 25 --- 9.0 ---
Voltage
0 --- --- ---
θ=0 Note1
Vth 25 --- 9.0 --- V
Φ= 0 Note2
Operating 40 --- --- ---
2
Voltage 0 --- --- ---
θ=0
Vsat 25 --- --- ---
Φ= 0
40 --- --- ---
0 --- --- ---
θ=0
Tr 25 --- 218 268
Φ= 10
40 --- --- ---
3 Response time ms Note4
0 --- --- ---
θ=0
Tf 25 --- 115 165
Φ= 10
40 --- --- ---
θ Φ=0° 25 -10 10 40
Viewing θ Φ=180° 25 30 10 ---
4 Deg Note1
Angle (Cr2) θ Φ=90° 25 30 --- ---
θ Φ=270° 25 --- --- ---
Current
5 ILCD Hz=64 25 --- 82 --- uA Note3
Consumption

NOTE 1: DEFINITION OF VIEWING ANGLE AND DIRECTION

Zθ =0°
θ Detector
°
12H Φ =180

3H Φ =90°

9H Φ =270° 6H Φ =0°

NOTE 2: THERSHOLD VOLTAGE AND SATURATION VOLTAGE

Vth: The voltage Vop which the transmission rate of segment is 90%(positive) or 10%(negative) of saturated value on conditions
of the selected waveform. (non-selected waveform is opposition)
Vsat: The voltage Vop which the transmission rate of segment is 10%(positive) or 10%(negative) of saturated value on
conditions of the selected waveform. (non-selected waveform is opposition)
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 5 of 21

NOTE 3: CURRENT CONSUMPTION (I LCD)

Conditions:
1.Driving waveform: static waveform. 2.Voltage applied to all segments

NOTE 4: RESPONSE TIME (Tr, Tf)

NOTE 5: CONTRAST RATIO (CR)

5.1 POSITIVE TYPE:
BRIGHTNESS AT VOP (NON-SELECTED)
CONTRAST RATIO =
BRIGHTNESS AT VOP (SELECTED)
5.2 NEGATIVE TYPE:
BRIGHTNESS AT VOP (SELECTED)
CONTRAST RATIO =
BRIGHTNESS AT VOP (NON-SELECTED)

NOTE 6: CAPACITANCE (C)

Conditions:
Voltage applied to all segments.
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 6 of 21

BLOCK DIAGRAM
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 7 of 21

MECHANCIAL DRAWING
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 8 of 21
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 9 of 21
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 10 of 21

BACKLIGHT DRAWING
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 11 of 21

BACKLIGHT SPECIFICATION
N MECHANICAL SPECIFICATIONS
ITEM NOMINAL DIMENSIONS UNIT
OUTLINE SIZE (LxWxH) 68.80 x 49.20 x 8.5 mm
VIEWING AREA (LxW) 61.60 x 34.10 mm
CONTACT PIN PITCH/LENGTH NIL mm
NO.OF LED SMT 3 ---

N ELECTRICAL/OPTICAL CHARACTERISTICS (Ta=25°C, If=60mA typ.)

MODE PARAMETER UNIT
COLOR WHITE ---
CHROMATICITY COORDINATE X=0.2884 Y=0.3041 ---
AVERAGE LUMINOUS INTENSITY (IV) 168 typ. cd/m2
FORWARD VOLTAGE (Vf) 3.2 typ. V

N ABSOLUTE MAXIMUM RATING

ITEM VALUE UNIT
FORWARD CURRENT 90mA If
REVERSE VOLTAGE 5V Vr
POWER DISSIPATION 288mW Pd
OPERATING TEMPERATURE -20°C TO 70°C Top
STORAGE TEMPERATURE -30°C TO 80°C Tstg

TESTING POINT CIRCUIT DIAGRAM

REMARK:
1. AVERAGE LUMINOUS INTENSITY IS THE AVERAGE VALUE OF THE NINE INDICATED POINTS AS
SHOWN.
2. MEASUREMENT INSTRUMENT: BM-7, APERTURE: ∅10mm.
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 12 of 21

QUALITY GUARANTEE
N PURPOSE: It is to define the inspection standard of LCD modules

N PRODUCT STANDARD
1) INSPECTION AND TEST
• FUNCTION TEST
• APPEARANCE INSPECTION
• PACKING SPECIFICTION

2) INSPECTION CONDITION
• Put under the lamp (20w×2) at a distance 100mm from the LCD Modules.
• Tilt upright 45 degree by the front (back) to inspect LCD appearance.

3) AQL INSPECTION LEVEL

L
A
M
P
• SAMPLING METHOD : MIL-STD-105D
• SAMPLING PLAN : SINGLE
• MAJOR DEFECT : 0.65% (MAJOR)
• MINOR DEFECT : 2.5% (MINOR)

O
P
E
R
A
T
O
R
• GENERAL LEVEL : II/NORMAL

L
C
M
N DISPLAY AREA DEFINITION:

View area

Viewing boundary
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 13 of 21

N INSPECTION STANDARD
1) FUNCTIONAL TEST STANDARD
Item Inspection Standard Description Standard Defect type
1 LCD has no display Reject MAJ
2 LCM display do not change Reject MAJ
3 Display wrong pattern Reject MAJ

Missing
4 Display segment open segment Reject MAJ
Missing
segment

5 Display dim segment Dim Reject MAJ

segment Dim
segment
6 Wrong LCD viewing direction Reject MAJ
See
7 Dim Display MAJ
sample
See
8 LCD color variation MAJ
sample
Pattern parallelism Acceptable range
L <a b
≧20mm | 0.43° | ≦0.15mm
≧30mm | 0.38° | ≦0.2mm
≧40mm | 0.43° | ≦0.3mm
9 ≧50mm | 0.40° | ≦0.35mm
Accept
≧60mm | 0.43° | ≦0.45mm
≧70mm | 0.41° | ≦0.50mm
≧80mm | 0.43° | ≦0.60mm
≧90mm | 0.41° | ≦0.65mm
≧100mm | 0.43° | ≦0.75mm
Standard
x+ y
Ø= QTY
2
Ø≦0.25 1 Accept
LCD display Ø>0.25 1 Accept
10
Pin hole 1
Ø< W 1 Accept
4
1
Ø> W 1 Reject MIN
4
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 14 of 21

Item Inspection Standard Description Standard Defect type

Draw Standard
X y QTY
1 1
≧ b ≧ a 1 Reject MIN
4 4
LCD display (X or y) ≧0.2mm 1 Reject MIN
11
Broken segment(dots)
1 1
≦ b ≦ a 1 Accept
4 4
1 1
≦ b ≦ a 2 Accept
5 5
x+ y
Ø= QTY
2
LCD display Ø<0.10 Accept
12 Black spot or 0.1<Ø≦0.20 2 Accept
White spot 0.20≦Ø<0.25 1 Accept
0.25< Ø≦0.4 0 Reject MIN
Ø>0.4 0 Reject MAJ
Black line/white line(L×w)mm QTY
(L≦1.0)×(W≦0.025) 2 Accept
13 LCD display excess black line or white line (1.0<L≦1.5)×(W≦一‧0.025) 1 Accept
(L>1.5)×(W≦0.025) 0 Reject MIN
(L>2)×(W>0.025) 0 Reject MAJ
14 Backlight not function Reject MAJ
15 LED not function or dim Reject MIN
16 Backlight defect (dirt, scratch) Reject MIN

2) COSMETIC INSPECTION STANDARD

Item Standard description of inspection Standard Defect type
1 LCD inspection item
See
1.1 LCD color variation MIN
sample

1.2 LCD broken Reject MAJ

1.3 Wrong polarizer of LCD Reject MAJ

1.4 Spot on LCD surface Reject MAJ
Scratch on LCD Scratch = Ø QTY
x Ø<0.1 Except Accept
0.1≦ø≦0.15 2 Accept
1.5 x+ y y 0.15< ø≦0.25 1 Accept
Ø=
2
Ø>0.25 1 Reject MIN

LCD scratch Scratch =L scratch =W QTY

W≦0.015 Accept
<0.5 W≦0.02 2 Accept
1.6
<1.0 W≦0.03 1 Accept
Scratch depth see sample ≧1.0 W≧0.03 1 Reject MIN

QTY
White or black spot on LCD Ø<0.1 Accept
1.7
x+ y 0.1≦Ø<0.2 2 Accept
Ø= 0.2≦Ø≦0.25 1 Accept
2
Ø>0.25 1 Reject MIN
Bevy point - Reject MIN
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 15 of 21

Item Standard description of inspection Standard Defect type

Black line in LCD (L) (W) QTY
L≦1.0 W≦0.025 2 Accept
1.8 1.0<1≦1.5 W≦0.025 1 Accept
1.5<L W>0.025 1 Reject MIN

Size QTY
Ø<0.15 2 Accept
1.9 Round air bubble
0.15≦Ø≦0.25 1 Accept
Ø>0.25 0 Reject MIN
(L) (W) QTY
L<0.5 W<0.02 2 Accept
1.10 Line defect
L<1.0 W<0.03 1 Accept
L≧1.0 W≧0.3 0 Reject MIN
1.11 Finger print Reject MIN
2 PCB/COB specification
PCB deformity L H
≦6.0mm ≦1.5mm Accept
2.1 >6.0mm ≦1.5mm Reject MIN
<6.0mm >1.5mm Reject MIN
>6.0mm >1.5mm Reject MIN
2.2 Deformity at PCB edge, damage circuit. Reject MAJ
L H
Convex at PCB edge ≦6.0mm ≦1.5mm Accept
2.3 >6.0mm ≦1.5mm Reject MIN
<6.0mm >1.5mm Reject MIN
>6.0mm >1.5mm Reject MIN
2.4 Damage excess 2x2mm at the PCB corner Reject MIN
2.5 Scratch on PCB surface See sample MIN
2.6 Scratch on PCB coat/leakage coat on PCB surface Reject MAJ
2.7 Open circuit Reject MAJ
2.8 PCB PTH open Reject MAJ
QTY≦2PCS Accept
2.9 Repair PCB PTH
QTY≧3PCS Reject MAJ
2.10 Color different from one side to another side. Reject MIN
≦30mm2 Accept
2.11 Repaired solder mask area
≧30mm2 Reject MIN
Scratch circuit, damage
Circuit a≦1/2w or b<w Accept
2.12
a>1/2w or b>w Reject

3 Bezel specification
3.1 Wrong Materials MAJ
3.2 Incorrect dimension MAJ
3.3 Bezel broken MAJ
3.4 Rust on Bezel MAJ
Size cm2/per
Ø≦0.3 2 Accept
Top surface 0.3<Ø≦0.5 1 Accept
Hole or dirty on oil
3.5 Ø>0.5 0 Reject MIN
Paint surface
Ø≦0.5 2 Accept
Side 0.5<Ø≦0.8 1 Accept
Ø>0.8 0 Reject MIN
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 16 of 21

Item Standard description of inspection Standard Defect type

h≦0.01 mm/mm Accept
3.6 Bezel bow or twist
h>0.01 mm/mm Reject MIN

d1-d2≦tolerance
Accept
3.7

d1-d2>tolerance Reject MIN

Scratch on bezel Face Accept
QTY
L W Not
- W≦0.15 defined
See
L≦3 W≦0.20 2
Sample
L≦2 W≦0.3 2
3.8 - W>0.3
side Accept
QTY
L W
- W≦0.2 except
See
L≦3 W≦0.25 2 Sample
L≦2 W≦0.3 2

3.9 Twist angle α=45º+5º Accept

3.10 Void gap between bezel and PCB Reject MIN

Bezel clip incorrectly

3.11 Reject MIN

NG
4 Solder specification
4.1 Wrong component Reject MAJ
4.2 Broken component Reject MAJ
Component legs extend beyond the pad and
Accept
Mis-alignment Legs >pad distance(w) on solder area >W2

Component legs extend beyond the pad and

Reject MIN
Legs >pad distance(w) on solder area <W2
4.3
Component Solder legs offset distance L<solder legs
Accept
Offset 1/4W

Solder legs offset L>1/4W Reject MIN

Component assembly defect

4.4 Reject MIN

4.5 CHIP components hoist≦0.5mm Accept

4.6 CHIP components hoist>0.5mm Reject MIN
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 17 of 21

Item Standard description of inspection Standard Defect type

h≦2.0mm Accept
4.7 Components hoist
h>2.0mm Reject MIN
h≦0.5mm Accept
4.8 Switch (socket) hoist
h>0.5mm Reject MIN
4.9 Components cold solder or incomplete solder Reject MAJ
Solder PAD tilt up, but height (h) less than
Solder PAD thickness (a)

4.10 Accept

Excess solder above components

4.11 Reject Min

Insufficient solder below

components height or less than diameter

4.12 Reject MIN

4.13 Solder area less than soldering PAD Area by 2/3 Reject MIN
Trimmed pin length beyond 0.09inch (2.3mm)

4.14 Reject Min

5 Packing specification
5.1 Wrong carton mark . Reject MAJ
5.2 Carton mark problem Reject MIN
5.3 Carton damage extend than 150mm Reject MAJ
5.4 Carton damage, scratch more 50mm, less 150mm. Reject MIN
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 18 of 21

PRECAUTIONS FOR USING LCD MODULES

N HANDLING PRECAUTIONS
1. This device is susceptible to Electro-Static Discharge (ESD) damage. Observe Anti-Static precautions.
2. The display panel is made of glass. Do not subject it to a mechanical shock by dropping it or impact.
3. If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in your mouth. If the
substance contacts your skin or clothes, wash it off using soap and water.
4. Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary.
5. The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully.
6. If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If it is heavily
contaminated, moisten cloth with one of the following solvents :
• Isopropyl alcohol
• Ethyl alcohol
7. Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the following.
• Water
• Ketone
• Aromatic solvents
8. Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water droplets, moisture
condensation or a current flow in a high-humidity environment.
9. Install the LCD Module by using the mounting holes. When mounting the LCD module make sure it is free of twisting,
warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable.
10. Do not attempt to disassemble or process the LCD module.
11. NC terminal should be open. Do not connect anything.
12. If the logic circuit power is off, do not apply the input signals.
13. To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment.
• Be sure to ground the body when handling the LCD modules.
• Tools required for assembling, such as soldering irons, must be properly grounded.
• To reduce the amount of static electricity generated, do not conduct assembling and other work under dry conditions.
• The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film
since static electricity may be generated.

N POWER SUPPLY PRECAUTIONS:

1. Identify and, at all times, observe absolute maximum ratings for both logic and LC drivers. Note that there is some variance
between models.
2. Prevent the application of reverse polarity to VDD and VSS, however briefly.
3. Use a clean power source free from transients. Power-up conditions are occasionally “jolting” and may exceed the maximum
ratings of the modules.
4. The VDD power of the module should also supply the power to all devices that may access the display. Don’t allow the data
bus to be driven when the logic supply to the module is turned off.

N OPERATING PRECAUTIONS:
1. DO NOT plug or unplug the module when the system is powered up.
2. Minimize the cable length between the module and host MPU.
3. For models with EL backlights, do not disable the backlight by interrupting the HV line. Unload inverters produce voltage
extremes that may arc within a cable or at the display.
4. Operate the module within the limits of the modules temperature specifications.

N MECHANICAL/ENVIRONMENTAL PRECAUTIONS:
1. Improper soldering is the major cause of module difficulty. Use of flux cleaner is not recommended as they may seep under
the elastomeric connection and cause display failure.
2. Mount the module so that it is free from torque and mechanical stress.
3. Surface of the LCD panel should not be touched or scratched. The display front surface is an easily scratched, plastic
polarizer. Avoid contact and clean only when necessary with soft, absorbent cotton dampened with petroleum benzene.
4. Always employ anti-static procedure while handling the module.
5. Prevent moisture build-up upon the module and observe the environmental constraints for storage temperature and humidity.
6. Do not store in direct sunlight
7. If leakage of the liquid crystal material should occur, avoid contact with this material, particularly ingestion. If the body
or clothing becomes contaminated by the liquid crystal material, wash thoroughly with water and soap
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 19 of 21

N Storage Precautions
When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. Keep the modules in
bags (avoid high temperature / high humidity and low temperatures below 0°C). Whenever possible, the LCD modules should be
stored in the same conditions in which they were shipped from our company.

N Others
Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the
generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low temperature.
If the LCD modules have been operating for a long time showing the same display patterns, the display patterns may
remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status can be regained
by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance reliability.
To minimize the performance degradation of the LCD modules resulting from destruction caused by static electricity etc.,
exercise care to avoid holding the following sections when handling the modules.
• Exposed area of the printed circuit board.
• Terminal electrode sections.

USING LCD MODULES

N Liquid Crystal Display Modules
LCD is composed of glass and polarizer. Pay attention to the following items when handling.
1. Please keep the temperature within specified range for use and storage. Polarization degradation, bubble generation or
polarizer peel-off may occur with high temperature and high humidity.
2. Do not touch, push or rub the exposed polarizers with anything harder than an HB pencil lead (glass, tweezers, etc.).
3. N-hexane is recommended for cleaning the adhesives used to attach front/rear polarizers and reflectors made of organic
substances which will be damaged by chemicals such as acetone, toluene, ethanol and isopropylalcohol.
4. When the display surface becomes dusty, wipe gently with absorbent cotton or other soft material like chamois soaked in
petroleum benzin. Do not scrub hard to avoid damaging the display surface.
5. Wipe off saliva or water drops immediately, contact with water over a long period of time may cause deformation or color
fading.
6. Avoid contacting oil and fats.
7. Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the polarizers. After products
are tested at low temperature they must be warmed up in a container before coming is contacting with room temperature air.
8. Do not put or attach anything on the display area to avoid leaving marks on.
9. Do not touch the display with bare hands. This will stain the display area and degradate insulation between terminals (some
cosmetics are determinated to the polarizers).
10. As glass is fragile. It tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring.

N Installing LCD Modules

The hole in the printed circuit board is used to fix LCM as shown in the picture below. Attend to the following items when
installing the LCM.
1. Cover the surface with a transparent protective plate to protect the polarizer and LC cell.

2. When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting plate should have
enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements. The
measurement tolerance should be ±0.1mm.
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 20 of 21

N Precaution for Handing LCD Modules

Since LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the
module or making any alterations or modifications to it.
1. Do not alter, modify or change the shape of the tab on the metal frame.
2. Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached.
3. Do not damage or modify the pattern writing on the printed circuit board.
4. Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.
5. Except for soldering the interface, do not make any alterations or modifications with a soldering iron.
6. Do not drop, bend or twist LCM.

N Electro-Static Discharge Control

Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as for an ordinary
CMOS IC.
1. Make certain that you are grounded when handing LCM.
2. Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body have the same
electric potential.
3. When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak.
4. When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as much as
possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor.
5. As far as possible make the electric potential of your work clothes and that of the work bench the ground potential.
6. To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative humidity of
50%-60% is recommended.

N Precaution for soldering to the LCM

1. Observe the following when soldering lead wire, connector cable and etc. to the LCM.
• Soldering iron temperature : 280°C ± 10°C.
• Soldering time : 3-4 sec.
• Solder : eutectic solder.
If soldering flux is used, be sure to remove any remaining flux after finishing to soldering operation. (This does not apply
in the case of a non-halogen type of flux.) It is recommended that you protect the LCD surface with a cover during soldering to
prevent any damage due to flux spatters.
2. When soldering the electroluminescent panel and PC board, the panel and board should not be detached more than three
times. This maximum number is determined by the temperature and time conditions mentioned above, though there may be
some variance depending on the temperature of the soldering iron.
3. When remove the electroluminescent panel from the PC board, be sure the solder has completely melted, the soldered pad on
the PC board could be damaged.

N Precautions for Operation

1. Viewing angle varies with the change of liquid crystal driving voltage (VO). Adjust VO to show the best contrast.
2. Driving the LCD in the voltage above the limit shortens its life.
3. Response time is greatly delayed at temperature below the operating temperature range. However, this does not mean the
LCD will be out of the order. It will recover when it returns to the specified temperature range.
4. If the display area is pushed hard during operation, the display will become abnormal. However, it will return to normal if it
is turned off and then back on.
5. Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore, it must be used
under the relative condition of 40°C , 50% RH.
6. When turning the power on, input each signal after the positive/negative voltage becomes stable.
Displaytech Ltd LCD MODULE 64128L SERIES Version : 1.1 P 21 of 21

N Storage
When storing LCDs as spares for some years, the following precaution are necessary.
1. Store them in a sealed polyethylene bag. If properly sealed, there is no need for desiccant.
2. Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature between 0°C and 35°C.
3. The polarizer surface should not come in contact with any other objects. (We advise you to store them in the container in
which they were shipped.)
4. Environmental conditions :
• Do not leave them for more than 168hrs. at 60°C.
• Should not be left for more than 48hrs. at -20°C.

N Safety
1. It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as acetone and
ethanol, which should later be burned.
2. If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off thoroughly with soap and water.

N Limited Warranty
Unless agreed between DISPLAYTECH and customer, DISPLAYTECH will replace or repair any of its LCD modules
which are found to be functionally defective when inspected in accordance with DISPLAYTECH LCD acceptance standards
(copies available upon request) for a period of one year from date of shipments. Cosmetic/visual defects must be returned to
DISPLAYTECH within 90 days of shipment. Confirmation of such date shall be based on freight documents. The warranty
liability of DISPLAYTECH limited to repair and/or replacement on the terms set forth above. DISPLAYTECH will not be
responsible for any subsequent or consequential events.

N Return LCM under warranty

No warranty can be granted if the precautions stated above have been disregarded. The typical examples of violations are :
• Broken LCD glass.
• PCB eyelet’s damaged or modified.
• PCB conductors damaged.
• Circuit modified in any way, including addition of components.
• PCB tampered with by grinding, engraving or painting varnish.
• soldering to or modifying the bezel in any manner.
Module repairs will be invoiced to the customer upon mutual agreement. Modules must be returned with sufficient
description of the failures or defects. Any connectors or cable installed by the customer must be removed completely without
damaging the PCB eyelet’s, conductors and terminals.

REVISION RECORD
VERSION CHANGES DATE
1.0 Initial revision 7 March 2008
1.1 Power Supply for Logic and LCD inside ABSOLUTE MAXIMUN RATINGS was 10 June 2008
corrected