Mercedes-Benz Mbe 900 Valve Lash Checking

https://truckmanualshub.
com/
Section 12.1
Valve Lash Checking
Note: Adjust the valve lash when the engine is cold. Wait at least 30 minutes after shutdown,
even if the engine ran only a short time.
1. In order, according to the timing sequence used for fuel injection (see Method One—
Adjust Each Cylinder in Firing Order);
2. By type of valve, depending on crankshaft position (see Method Two—Adjust All Valves
Using Two Crankshaft Positions). See Figure "Cylinder and Valve Layout" for the
cylinder and valve layout on both the 4– and 6–cylinder engines.
Figure 1. Cylinder and Valve Layout
Section 12.1.1
Method One — Adjust Each Cylinder in Firing Order
Method one allows you to adjust each cylinder in the order in which fuel is injected. The
crankshaft must be repositioned after each cylinder is adjusted as listed in Table "Valve
Adjustment (Method One)"
–
https://truckmanualshub.com/
Table 1. Valve Adjustment (Method One)
Note: Clean the cylinder head cover before removing it.
1. Remove the cylinder head cover. Refer to "1.1.1 Cylinder Head Cover Removal" . See
Figure "Cylinder Head Cover" .
-
-
Figure 2. Cylinder Head Cover
2. Remove the inspection cover on the flywheel housing.

3. Install the engine barring tool J-46392 or W904589046300 into the inspection hole on the
flywheel housing. Refer to "1.13 Engine Barring Tool" . See Figure "Inspection Hole in
the Flywheel Housing" .
Figure 3. Inspection Hole in the Flywheel Housing
4. For each cylinder, use the cranking tool to rotate the crankshaft until the piston is exactly
at top dead center (TDC) in the compression stroke. The valves must be closed and it
must be possible to turn the pushrods without effort.
Note: When the piston in cylinder #1 is at ignition TDC, the valves of cylinder #6
(cylinder #4 on the 4-cylinder engine) will overlap, meaning that both intake and exhaust
valves are partially open, and show no measurable play when tested with a feeler gauge.
5. Check each valve and if necessary, adjust it using the remaining steps.
6. For each valve, measure the valve lash with a feeler gauge between the rocker arm and
valve stem (exhaust valve) or valve bridge (intake valve). It should be possible to pull the
feeler gauge through with no more than light resistance.
7. If the value measured is within the range given in the "Check For" column listed in Table
"Valve Lash Checking and Adjustment" , check the next valve.
8. Table 3. Valve Lash Checking and Adjustment
If the value measured is outside the range given in the "Check For" column listed in
Table "Valve Lash Checking and Adjustment" , adjust the valve lash. Refer to "12.2
Adjusting Valve Lash"
Section 12.1.2
Adjust All Valves Using Two Crankshaft Positions
Method two a
Note: Clean the cylinder head cover before removing it.
1. Remove the cylinder head cover. Refer to "1.1.1 Cylinder Head Cover Removal" . See
Figure "Cylinder Head Cover" .
-
-
Figure 4. Cylinder Head Cover
2. Remove the inspection cover on the flywheel housing.

Figure 5. Inspection Hole in the Flywheel Housing
3. Install the engine barring tool J-46392 or W904589046300 into the inspection hole on the
flywheel housing. Refer to "1.13 Engine Barring Tool" . See Figure "Inspection Hole in
the Flywheel Housing" .
4. Using the cranking tool, rotate the crankshaft until cylinder #1 is at the ignition TDC
position (all valves are closed) and cylinder #6 (cylinder #4 on a 4-cylinder engine) is at
the valve overlap position (all valves are open).
5. Check the valves in the "Ignition TDC" row listed in Table "Valve Adjustment (Method
Two)" and adjust them (if necessary), using the remaining steps.
—
–
—
—
–
—
6. Table 5. Valve Adjustment (Method Two)

7.
*NOTE: I = Intake Valve and E = Exhaust Valve
8. Using the cranking tool, rotate the crankshaft until cylinder #6 (cylinder #4 on a 4-
cylinder engine) is at the ignition TDC position (all valves are closed) and cylinder #1 is
at the valve overlap position (all valves are open).
9. Using the same procedure, check the valves in the "Valve Overlap" row listed in Table
"Valve Adjustment (Method Two)" and adjust them (if necessary), using the remaining
steps.
10. For each valve, measure the valve lash with a feeler gauge between the rocker arm and
valve stem (exhaust valve) or valve bridge (intake valve). It should be possible to pull the
feeler gauge through with no more than light resistance.
11. If the value measured is within the range given in the "Check For" column listed in Table
"Valve Lash Checking and Adjustment" , check the next valve.
12. Table 6. Valve Lash Checking and Adjustment
If the value measured is outside the range given in the "Check For" column listed in
Table "Valve Lash Checking and Adjustment" , adjus
EPA98/04 MBE 900 Workshop Manual (DDC-SVC-MAN-0024)
Copyright © 2016 by Detroit Diesel Corporation. All rights reserved.
Generated on 11-23-2016

Mercedes-Benz Mbe 900 Valve Lash Checking

Uploaded by

Copyright:

Available Formats

Mercedes-Benz Mbe 900 Valve Lash Checking

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mercedes-Benz Mbe 900 Valve Lash Checking

Uploaded by

Copyright:

Available Formats

https://truckmanualshub.

Figure 1. Cylinder and Valve Layout

Table 1. Valve Adjustment (Method One)

Note: Clean the cylinder head cover before removing it.

Figure 2. Cylinder Head Cover

2. Remove the inspection cover on the flywheel housing.

Figure 3. Inspection Hole in the Flywheel Housing

8. Table 3. Valve Lash Checking and Adjustment

Note: Clean the cylinder head cover before removing it.

Figure 4. Cylinder Head Cover

2. Remove the inspection cover on the flywheel housing.

Figure 5. Inspection Hole in the Flywheel Housing

6. Table 5. Valve Adjustment (Method Two)

12. Table 6. Valve Lash Checking and Adjustment

EPA98/04 MBE 900 Workshop Manual (DDC-SVC-MAN-0024)

Copyright © 2016 by Detroit Diesel Corporation. All rights reserved.

You might also like