SAFETY DATA SHEET

Marathon Comp A
Section 1. Identification
GHS product identifier : Marathon Comp A
Other means of identification : Not available.
Product code : 574
Product description : Not available.
Product type : Liquid.

Relevant identified uses of the substance or mixture and uses advised against

Identified uses
Use in coatings - Industrial use
Use in coatings - Professional use

Manufacturing country : Jotun Thailand Limited

700/353 Amata Nakorn Industrial Estate (BIP 2)
Moo 6, Tumbol Donhualoh, Amphur Muang Chonburi
Chonburi 20000 Thailand

Phone: + 66 2 022 9888

Fax: + 66 2 022 9888 , + 66 38 214 375

[email protected]

Emergency telephone number : Jotun Thailand Limited

Phone: + 66 2 022 9888 ext. 2100, 2400, 2402

574;576 1,2 574

^(ValidationDate) 1
Approved

Section 2. Hazards identification

Classification of the : FLAMMABLE LIQUIDS - Category 3
substance or mixture SKIN CORROSION/IRRITATION - Category 2
SERIOUS EYE DAMAGE/EYE IRRITATION - Category 1
SKIN SENSITISATION - Category 1
LONG-TERM (CHRONIC) AQUATIC HAZARD - Category 2

GHS label elements

Hazard pictograms :

Signal word : Danger.

Hazard statements : H226 - Flammable liquid and vapour.
H315 - Causes skin irritation.
H317 - May cause an allergic skin reaction.
H318 - Causes serious eye damage.
H411 - Toxic to aquatic life with long lasting effects.
Precautionary statements
Prevention : P280 - Wear protective gloves. Wear eye or face protection.
P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking.
P273 - Avoid release to the environment.
P261 - Avoid breathing vapour.

Date of issue : 19.04.2023 1/11

Marathon Comp A

Section 2. Hazards identification

Response : P391 - Collect spillage.
P362 - Take off contaminated clothing and wash before reuse.
P363 - Wash contaminated clothing before reuse.
P302 + P352 - IF ON SKIN: Wash with plenty of water.
P333 + P313 - If skin irritation or rash occurs: Get medical advice or attention.
P305 + P351 + P338, P310 - IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Immediately call a POISON CENTER or doctor.
Storage : P403 + P235 - Store in a well-ventilated place. Keep cool.
Disposal : P501 - Dispose of contents and container in accordance with all local, regional,
national and international regulations.

Other hazards which do not : None known.

result in classification

Section 3. Composition/information on ingredients

Substance/mixture : Mixture
Other means of identification : Not available.

CAS number/other identifiers

CAS number : Not applicable.
EC number : Mixture.
Product code : 574
Ingredient name % CAS number
epoxy resin (MW ≤ 700) ≥25 - ≤50 1675-54-3
xylene ≤10 1330-20-7
epoxy resin (MW 700-1200) ≤10 25036-25-3
butan-1-ol ≤5 71-36-3
ethylbenzene ≤3 100-41-4
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this
section.
Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures

Description of necessary first aid measures
Eye contact : Get medical attention immediately. Call a poison center or physician. Immediately
flush eyes with plenty of water, occasionally lifting the upper and lower eyelids.
Check for and remove any contact lenses. Continue to rinse for at least 10 minutes.
Chemical burns must be treated promptly by a physician.
Inhalation : Get medical attention immediately. Call a poison center or physician. Remove
victim to fresh air and keep at rest in a position comfortable for breathing. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel.
It may be dangerous to the person providing aid to give mouth-to-mouth
resuscitation. If unconscious, place in recovery position and get medical attention
immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie,
belt or waistband.
Skin contact : Get medical attention immediately. Call a poison center or physician. Wash with
plenty of soap and water. Remove contaminated clothing and shoes. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
Continue to rinse for at least 10 minutes. Chemical burns must be treated promptly
by a physician. In the event of any complaints or symptoms, avoid further exposure.
Wash clothing before reuse. Clean shoes thoroughly before reuse.

Date of issue : 19.04.2023 2/11

Marathon Comp A

Section 4. First aid measures

Ingestion : Get medical attention immediately. Call a poison center or physician. Wash out
mouth with water. Remove dentures if any. If material has been swallowed and the
exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should
be kept low so that vomit does not enter the lungs. Chemical burns must be treated
promptly by a physician. Never give anything by mouth to an unconscious person.
If unconscious, place in recovery position and get medical attention immediately.
Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or
waistband.

Most important symptoms/effects, acute and delayed

Potential acute health effects
Eye contact : Causes serious eye damage.
Inhalation : No known significant effects or critical hazards.
Skin contact : Causes skin irritation. May cause an allergic skin reaction.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : Adverse symptoms may include the following:
pain
watering
redness
Inhalation : No specific data.
Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
blistering may occur
Ingestion : Adverse symptoms may include the following:
stomach pains

Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments : No specific treatment.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. If it
is suspected that fumes are still present, the rescuer should wear an appropriate
mask or self-contained breathing apparatus. It may be dangerous to the person
providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing
thoroughly with water before removing it, or wear gloves.

See toxicological information (Section 11)

Section 5. Firefighting measures

Extinguishing media
Suitable extinguishing media : Use dry chemical, CO₂, water spray (fog) or foam.
Unsuitable extinguishing : Do not use water jet.
media

Specific hazards arising from : Flammable liquid and vapour. Runoff to sewer may create fire or explosion hazard.
the chemical In a fire or if heated, a pressure increase will occur and the container may burst, with
the risk of a subsequent explosion. This material is toxic to aquatic life with long
lasting effects. Fire water contaminated with this material must be contained and
prevented from being discharged to any waterway, sewer or drain.
Hazardous thermal : Decomposition products may include the following materials:
decomposition products carbon dioxide
carbon monoxide
metal oxide/oxides

Date of issue : 19.04.2023 3/11

Marathon Comp A

Section 5. Firefighting measures

Special protective actions for : Promptly isolate the scene by removing all persons from the vicinity of the incident if
fire-fighters there is a fire. No action shall be taken involving any personal risk or without
suitable training. Move containers from fire area if this can be done without risk.
Use water spray to keep fire-exposed containers cool.
Special protective equipment : Fire-fighters should wear appropriate protective equipment and self-contained
for fire-fighters breathing apparatus (SCBA) with a full face-piece operated in positive pressure
mode.

Section 6. Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilt material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Do not breathe vapour or mist.
Provide adequate ventilation. Wear appropriate respirator when ventilation is
inadequate. Put on appropriate personal protective equipment.
For emergency responders : If specialised clothing is required to deal with the spillage, take note of any
information in Section 8 on suitable and unsuitable materials. See also the
information in "For non-emergency personnel".

Environmental precautions : Avoid dispersal of spilt material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air). Water polluting material. May be harmful
to the environment if released in large quantities. Collect spillage.

Methods and material for containment and cleaning up

Small spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble.
Alternatively, or if water-insoluble, absorb with an inert dry material and place in an
appropriate waste disposal container. Dispose of via a licensed waste disposal
contractor.
Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach the release from upwind. Prevent entry into
sewers, water courses, basements or confined areas. Wash spillages into an
effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth
and place in container for disposal according to local regulations (see Section 13).
Dispose of via a licensed waste disposal contractor. Contaminated absorbent
material may pose the same hazard as the spilt product. Note: see Section 1 for
emergency contact information and Section 13 for waste disposal.

Section 7. Handling and storage

Precautions for safe handling : Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before
eating, drinking and smoking. Remove contaminated clothing and protective
equipment before entering eating areas. See also Section 8 for additional
information on hygiene measures.

Conditions for safe storage, : Store in accordance with local regulations. Store in a segregated and approved
including any incompatibilities area. Store in original container protected from direct sunlight in a dry, cool and well-
ventilated area, away from incompatible materials (see Section 10) and food and
drink. Store locked up. Eliminate all ignition sources. Separate from oxidising
materials. Keep container tightly closed and sealed until ready for use. Containers
that have been opened must be carefully resealed and kept upright to prevent
leakage. Do not store in unlabelled containers. Use appropriate containment to
avoid environmental contamination. See Section 10 for incompatible materials
before handling or use.

Date of issue : 19.04.2023 4/11

Marathon Comp A

Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
Ingredient name Exposure limits
xylene Ministry of Labor (Thailand, 8/2017).
TWA: 100 ppm 8 hours.
butan-1-ol Ministry of Labor (Thailand, 8/2017).
TWA: 100 ppm 8 hours.
ethylbenzene Ministry of Labor (Thailand, 8/2017).
TWA: 100 ppm 8 hours.
Recommended monitoring : Reference should be made to appropriate monitoring standards. Reference to
procedures national guidance documents for methods for the determination of hazardous
substances will also be required.

Appropriate engineering : Use only with adequate ventilation. Use process enclosures, local exhaust
controls ventilation or other engineering controls to keep worker exposure to airborne
contaminants below any recommended or statutory limits. The engineering controls
also need to keep gas, vapour or dust concentrations below any lower explosive
limits. Use explosion-proof ventilation equipment.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process
equipment will be necessary to reduce emissions to acceptable levels.

Individual protection measures

Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye/face protection : Safety eyewear complying to ISO 16321-1:2022 should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn,
unless the assessment indicates a higher degree of protection: chemical splash
goggles and/or face shield. If inhalation hazards exist, a full-face respirator may be
required instead.
Skin protection
Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should
be worn at all times when handling chemical products if a risk assessment indicates
this is necessary. Considering the parameters specified by the glove manufacturer,
check during use that the gloves are still retaining their protective properties. It
should be noted that the time to breakthrough for any glove material may be
different for different glove manufacturers. In the case of mixtures, consisting of
several substances, the protection time of the gloves cannot be accurately
estimated.
There is no one glove material or combination of materials that will give unlimited
resistance to any individual or combination of chemicals.
The breakthrough time must be greater than the end use time of the product.
The instructions and information provided by the glove manufacturer on use,
storage, maintenance and replacement must be followed.
Gloves should be replaced regularly and if there is any sign of damage to the glove
material.
Always ensure that gloves are free from defects and that they are stored and used
correctly.
The performance or effectiveness of the glove may be reduced by physical/chemical
damage and poor maintenance.
Barrier creams may help to protect the exposed areas of the skin but should not be
applied once exposure has occurred.

Date of issue : 19.04.2023 5/11

Marathon Comp A

Section 8. Exposure controls/personal protection

Wear suitable gloves tested to ISO 374-1:2016.
May be used, gloves(breakthrough time) 4 - 8 hours: Viton® (> 0.7 mm), neoprene
(> 0.35 mm), butyl rubber (> 0.4 mm), PVC (> 0.5 mm)
Recommended, gloves(breakthrough time) > 8 hours: nitrile rubber (> 0.4 mm), 4H/
Silver Shield® (> 0.07 mm), Teflon (> 0.35 mm), polyvinyl alcohol (PVA) (> 0.3 mm)

Body protection : Personal protective equipment for the body should be selected based on the task
being performed and the risks involved and should be approved by a specialist
before handling this product. When there is a risk of ignition from static electricity,
wear anti-static protective clothing. For the greatest protection from static
discharges, clothing should include anti-static overalls, boots and gloves.
Other skin protection : Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Respiratory protection : Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
If workers are exposed to concentrations above the exposure limit, they must use a
respirator according to EN 140. Use respiratory mask with charcoal and dust filter
when spraying this product, according to EN 14387(as filter combination A2-P2). In
confined spaces, use compressed-air or fresh-air respiratory equipment. When use
of roller or brush, consider use of charcoalfilter.

Section 9. Physical and chemical properties

Appearance
Physical state : Liquid.
Colour : Black, Brown., Green., Grey, Off-white., Red, White., Yellow.
Odour : Characteristic.
Odour threshold : Not available.
pH : Not applicable.
Melting point : Not applicable.
Boiling point : Lowest known value: 119°C (246.2°F) (butan-1-ol). Weighted average: 244.52°C
(472.1°F)
Flash point : Closed cup: 30°C (86°F)
Burning time : Not applicable.
Burning rate : Not applicable.
Evaporation rate : Highest known value: 0.84 (ethylbenzene) Weighted average: 0.69compared with
butyl acetate
Flammability (solid, gas) : Not applicable.
Lower and upper explosive : 0.8 - 11.3%
(flammable) limits
Vapour pressure : Highest known value: 1.2 kPa (9.3 mm Hg) (at 20°C) (ethylbenzene). Weighted
average: 0.26 kPa (1.95 mm Hg) (at 20°C)
Vapour density : Highest known value: 11.7 (Air = 1) (epoxy resin (MW ≤ 700)). Weighted average:
9.47 (Air = 1)
Relative density : 1.364 to 1.491 g/cm³
Solubility : Insoluble in the following materials: cold water and hot water.
Partition coefficient: n-octanol/ : Not available.
water
Auto-ignition temperature : Lowest known value: 355°C (671°F) (butan-1-ol).
Decomposition temperature : Not available.
SADT : Not available.
Viscosity : Kinematic (40°C): >20.5 mm2/s (>20.5 cSt)
Aerosol product

Date of issue : 19.04.2023 6/11

Marathon Comp A

Section 9. Physical and chemical properties

Section 10. Stability and reactivity

Reactivity : No specific test data related to reactivity available for this product or its ingredients.
Chemical stability : The product is stable.
Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions
Conditions to avoid : Avoid all possible sources of ignition (spark or flame). Do not pressurise, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition.
Incompatible materials : Keep away from the following materials to prevent strong exothermic reactions:
oxidising agents, strong alkalis, strong acids.
Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products
products should not be produced.

Section 11. Toxicological information

Information on toxicological effects
Acute toxicity
Product/ingredient name Result Species Dose Exposure
epoxy resin (MW ≤ 700) LD50 Dermal Rabbit 20 g/kg -
LD50 Oral Mouse 15600 mg/kg -
xylene LC50 Inhalation Vapour Rat 20 mg/l 4 hours
LD50 Oral Rat 4300 mg/kg -
TDLo Dermal Rabbit 4300 mg/kg -
butan-1-ol LD50 Oral Rat 790 mg/kg -
ethylbenzene LC50 Inhalation Vapour Rat - Male 17.8 mg/l 4 hours
LD50 Dermal Rabbit >5000 mg/kg -
LD50 Oral Rat 3500 mg/kg -
Irritation/Corrosion
Product/ingredient name Result Species Score Exposure Observation
epoxy resin (MW ≤ 700) Eyes - Severe irritant Rabbit - 24 hours 2 -
milligrams
Skin - Mild irritant Rabbit - 500 -
milligrams
xylene Eyes - Mild irritant Rabbit - 87 milligrams -
Skin - Mild irritant Rat - 8 hours 60 -
microliters
epoxy resin (MW 700-1200) Eyes - Mild irritant Mammal - - - -
species
unspecified
Skin - Mild irritant Mammal - - - -
species
unspecified
Sensitisation
Product/ingredient name Route of Species Result
exposure
epoxy resin (MW ≤ 700) skin Mammal - species Sensitising
unspecified
epoxy resin (MW 700-1200) skin Mammal - species Sensitising
unspecified
Mutagenicity
Not available.
Carcinogenicity
Not available.
Reproductive toxicity

Date of issue : 19.04.2023 7/11

Marathon Comp A

Section 11. Toxicological information

Not available.
Teratogenicity
Not available.
Specific target organ toxicity (single exposure)
Name Category Route of Target organs
exposure
xylene Category 3 - Respiratory tract
irritation
butan-1-ol Category 3 - Respiratory tract
irritation
Category 3 Narcotic effects
Specific target organ toxicity (repeated exposure)
Name Category Route of Target organs
exposure
ethylbenzene Category 2 - hearing organs
Aspiration hazard
Name Result
xylene ASPIRATION HAZARD - Category 1
ethylbenzene ASPIRATION HAZARD - Category 1

Potential acute health effects

Eye contact : Causes serious eye damage.
Inhalation : No known significant effects or critical hazards.
Skin contact : Causes skin irritation. May cause an allergic skin reaction.
Ingestion : No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics

Inhalation : No specific data.
Ingestion : Adverse symptoms may include the following:
stomach pains
Skin contact : Adverse symptoms may include the following:
pain or irritation
redness
blistering may occur
Eye contact : Adverse symptoms may include the following:
pain
watering
redness

Potential chronic health effects

General : Once sensitized, a severe allergic reaction may occur when subsequently exposed
to very low levels.
Carcinogenicity : No known significant effects or critical hazards.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.

Numerical measures of toxicity

Acute toxicity estimates

Date of issue : 19.04.2023 8/11

Marathon Comp A

Section 11. Toxicological information

Route ATE value
Oral 13157.89 mg/kg
Dermal 15206.5 mg/kg
Inhalation (vapours) 201.15 mg/l

Section 12. Ecological information

Toxicity
Product/ingredient name Result Species Exposure
epoxy resin (MW ≤ 700) Acute EC50 1.4 mg/l Daphnia 48 hours
Acute LC50 3.1 mg/l Fish - pimephales promelas 96 hours
Chronic NOEC 0.3 mg/l Fish 21 days
xylene Acute LC50 8500 μg/l Marine water Crustaceans - Palaemonetes 48 hours
pugio
Acute LC50 13400 μg/l Fresh water Fish - Pimephales promelas 96 hours
ethylbenzene Acute EC50 7700 μg/l Marine water Algae - Skeletonema costatum 96 hours
Acute EC50 2.93 mg/l Daphnia 48 hours
Acute LC50 4.2 mg/l Fish 96 hours

Persistence and degradability

Product/ingredient name Aquatic half-life Photolysis Biodegradability
epoxy resin (MW ≤ 700) - - Not readily
xylene - - Readily
ethylbenzene - - Readily

Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
epoxy resin (MW ≤ 700) 2.64 to 3.78 31 low
xylene 3.12 8.1 to 25.9 low
butan-1-ol 1 - low
ethylbenzene 3.6 - low

Mobility in soil
Soil/water partition : Not available.
coefficient (KOC)

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimised wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation and
any regional local authority requirements. Dispose of surplus and non-recyclable
products via a licensed waste disposal contractor. Waste should not be disposed of
untreated to the sewer unless fully compliant with the requirements of all authorities
with jurisdiction. Waste packaging should be recycled. Incineration or landfill
should only be considered when recycling is not feasible. This material and its
container must be disposed of in a safe way. Care should be taken when handling
emptied containers that have not been cleaned or rinsed out. Empty containers or
liners may retain some product residues. Vapour from product residues may create
a highly flammable or explosive atmosphere inside the container. Do not cut, weld
or grind used containers unless they have been cleaned thoroughly internally. Avoid
dispersal of spilt material and runoff and contact with soil, waterways, drains and
sewers.
Date of issue : 19.04.2023 9/11
Marathon Comp A

Section 13. Disposal considerations

Section 14. Transport information

UN IMDG IATA
UN number UN1263 UN1263 UN1263

UN proper shipping Paint Paint. Marine pollutant (epoxy Paint

name resin (MW ≤ 700))
Transport hazard 3 3 3
class(es)

Packing group III III III

Environmental Yes. The environmentally Yes. Yes. The environmentally
hazards hazardous substance mark is hazardous substance mark is
not required. not required.
Special precautions Transport within user’s Transport within user’s Transport within user’s
for user premises: always transport in premises: always transport in premises: always transport
closed containers that are closed containers that are in closed containers that are
upright and secure. Ensure upright and secure. Ensure upright and secure. Ensure
that persons transporting the that persons transporting the that persons transporting the
product know what to do in product know what to do in product know what to do in
the event of an accident or the event of an accident or the event of an accident or
spillage. spillage. spillage.
Additional - The marine pollutant mark is The environmentally
information not required when transported hazardous substance mark
in sizes of ≤5 L or ≤5 kg. may appear if required by
Emergency schedules F-E, other transportation
S-E regulations.

Transport in bulk according to : Not available.

IMO instruments
ADR / RID : Tunnel restriction code: (D/E)
Hazard identification number: 30

Section 15. Regulatory information

Hazardous Substance Act B.E. 2535 (1992)
Type
Ingredient name Type Authority Conditions

No known specific national and/or regional regulations applicable to this product

(including its ingredients).

Section 16. Other information

History
Date of printing : 19.04.2023
Date of issue/Date of revision : 19.04.2023
Date of previous issue : 21.08.2020
Version : 2.09

Date of issue : 19.04.2023 10/11

Marathon Comp A

Section 16. Other information

Key to abbreviations : ADN = European Provisions concerning the International Carriage of Dangerous
Goods by Inland Waterway
ADR = The European Agreement concerning the International Carriage of
Dangerous Goods by Road
ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
MARPOL = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
RID = The Regulations concerning the International Carriage of Dangerous Goods
by Rail
UN = United Nations
LogPow = logarithm of the octanol/water partition coefficient
References : Not available.
Indicates information that has changed from previously issued version.
Notice to reader
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and practical
experience. Jotun's products are considered as semi-finished goods and as such, products are often used under
conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product itself. Minor product
variations may be implemented in order to comply with local requirements. Jotun reserves the right to change the
given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs and
specific application practices.

If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.

Date of issue : 19.04.2023 11/11