CCTV

Download as doc, pdf, or txt
Download as doc, pdf, or txt
You are on page 1of 69

Integrated electronic security system

An electrical devices that sets off an alarm when


someone tries to break in security system.
 Security system-a system that enforces
boundaries between computer networks.
Security system consisting of a combination of
hardware and software that limits the exposure
of a computer.
Video surveillance systems monitor activities in
public areas, businesses or commercial buildings
for real-time or later review.

With the help of digital storage you
can identify people and provide
evidences that a series of events has
occurred.

Video surveillance improves security
and safety ,and is used today in sectors
ranging from retail to industrial
complexes and other types of buildings.
Introduction :installation of CCTV camera

This procedure covers the following
installation and configuration areas.
 System Installation – The physical cabling
and connections to install the system
 System Configuration – Configuring DVR
and router to meet the customer’s
requirements
 Special Camera – Installing PTZ and/or IDN
cameras
External TV Monitor – Setting up remote TV
monitoring of a single camera or the DVR
System Installation
Cable Connections and Assembly

The first step in installing the video
surveillance system is running the
Siamese cable between the various
camera locations and the DVR.

The following procedure gives you
step by step instructions on how to
terminate the Siamese cable for both
the video portion (RG59 coaxial cable
with BNC connectors) and the power
portion (18 AWG Black and Red or
Black and White pair).
Assemble tools and
connectors Tools Required

RG-59 Crimp Tool

Diagonal


Cutters Knife

BNC Connectors & Sleeves (2 per
camera)

1 at camera location & 1 at DVR
location

Split the power (black & white
or black & red) pair away from
the RG59 coaxial cable for about
6 inches at the camera location.

At the DVR location the split
will need to be enough to connect
the RG59 coaxial cable to the
DVR and the power pair to the
Power Distribution Unit.

Insert the metal sleeve over the
RG59 coaxial cable.

Cut approximately 1 inch of the
outer shell from the cable
exposing the copper shield.
Please NOTE: The narrow/smaller
end of the sleeve needs to be
inserted over the RG59 cable
FIRST!
about 3/8 inch. Fold this back on
the outer jacket.
Use the knife to carefully
trim back the inner
insulator around the copper
center wire. You should
leave about 1/16 to 1/8 inch
insulator beyond the shield.
The inner copper wire
should be about 1/2 inch
long.

Carefully insert the BNC
connector over the inner
copper wire sliding it
firmly back towards the
shield portion until it is in
place and the shield is
touching the sleeve
portion of the connector.
Pull the copper shield wire over the
rear portion of the BNC connector.
Slide the metal sleeve up OVER the copper
shield. Ensure that you are securely holding the
BNC connector against the RG59 cable.
Often when you slide up the sleeve you will
push the connector away from the inner core
wire unless you are holding it securely.
 Crimp the metal sleeve onto the BNC connector
using the larger (inner die) of your crimp tool.
Now crimp the narrow end of the sleeve over
the RG59 cable using the smaller (outer die) of
your crimp tool.
 The completed BNC assembly should look like the
picture.
 Power wire preparation.
 Remove about two inches of the outer shield from
the power portion of the Siamese cable.
 Remove about 3/8 inch insulation from each of
the wires.
Power Connections
 Before we start with power connections we need
to add a little information about camera types &
groups. There are two basic camera groups that
are used with video surveillance systems and each
has it’s own unique cabling and power issues.
The first camera group is modular cameras. The
modular cameras are the most versatile because
you have many different options to chose from
starting with the basic camera body (12 VDC, 24
VAC, color or black and white), then you can
select
 a lens (auto Iris, manual Iris, telephoto, standard, etc.),
and the mounting bracket (indoor, outdoor, color, etc.).
This is the more common option because the customer
can build a camera to meet his requirements for any
camera location.
 The second group of cameras is the All-in-One (AIO)
versions. These cameras are normally 12 VDC but may
also be found with the 24 VAC option. The cameras that
fall into this group are domes cameras, bullet cameras,
day/night color/infrared, covert cameras and most of the
pan/tilt/zoom cameras. The lens, power connections and
mount are included as part of the basic camera and does
not normally require any assembly when they are
installed.
 Connections for the modular cameras will look similar
to the various connections shown at the right. These
cameras are powered either by 12 VDC or 24 VAC.
 Ifpower
the camera is a 12 VDC camera it is imperative that the
cables be connected to the proper terminals.
 If the camera is a 12 VDC camera it is imperative that the
power cables be connected to the proper terminals.
 The BLACK power lead is always connected to the
Negative (-) terminal of the camera and the WHITE (or
RED) power lead to the Positive (+) terminal of the
camera.
 Although it is not required, the same process is
recommended for 24 VAC cameras to ensure continuity
when connecting up the system.
Connections for the all-in-one (AIO) cameras
will look similar to the various connections
shown at the right. These cameras are normally
powered by 12 VDC.
These cameras will normally have a receptacle
for power input and the center pin of the
receptacle is Positive.
The cameras can be powered by a single brick
with the proper plug or an adapter cable with
the correct plug will be shipped with the camera
to enable connection the power wires of the
Siamese cable.
If the camera requires 12 VDC, the power
source MUST be connected to the proper
terminals.
The BLACK power lead is always connected
to the Negative (-) terminal of the camera
and the WHITE (or RED) power lead to the
Positive (+) terminal of the camera.
Although it is not required, the same
process is recommended for 24 VAC
cameras to ensure continuity when
connecting up the system.
Connections for the all-in-one (AIO) cameras will
look similar to the various connections shown at
the right. These cameras are normally powered by
12 VDC.
These cameras will normally have a receptacle for
power input and the center pin of the receptacle
is Positive.
The cameras can be powered by a single brick
with the proper plug or an adapter cable with the
correct plug that is shipped with the camera to
enable connection the power wires of the Siamese
cable.
There are two options for power connections at
the DVR end of the cable.
A Power Distribution Unit (PDU) or a single
power source (commonly called a brick) for
each camera. Both type of power sources come
in 12 VDC and 24 VAC version.
A 24VAC version of the PDU is shown. All
connections are identical for both versions.
Black wires are connected to the Negative or
Common connection and the White (or Red)
wire to the Positive connection.
 Camera Assembly (Modular Cameras) and
Installation

 The next step is to assemble the modular cameras and


then install the cameras in the locations indicated by the
customer. Modular cameras will require assembly of a
lens and mounting bracket prior to installation. The all-
in-one cameras are completely assembled during
manufacturing and will require only installation and
connection to the DVR and power.
 Most modular cameras are similar to the 12 VDC camera
used for this example. If you have any questions about
any assembly instructions for the version of camera that
you have received, please called VS Technical Support
for assistance.
 Remove camera from box and install the bracket mount on
the top or bottom of the camera.
 Install the bracket mount on the top for cameras that will
be hanging from ceiling brackets or from wall mounted
brackets.
 The picture shows the bracket mount installed on the top of the
camera.
Some cameras will have a larger silver ring to
mount “C” type camera lenses. Look at the
camera documentation to determine if the “C”
mounting ring has been included with the
camera. This ring is rarely used and is not
required for the lenses shipped for this
installation. If this ring has been included it must
be removed before installing the lens.
 Insert the lens into the mounting bracket on the camera.
Rotate the lens until it has been screwed
in completely and snugly.
 Ensure the lens is inserted tightly but DO NOT
over tighten as you could strip the lens threads.
 Insert
camera.
the auto-iris cable into the back of the
 This is an example of a camera mounted with an
indoor mounting assembly.
After the camera has been mounted connect the
power wires to the camera.
Connect the Black (common/negative) wire to
the Negative ( - ) terminal on the camera.
Connect the Red or White (hot/positive) wire to
the Positive ( + ) terminal on the back of the
camera.
If you are using a single power source or “Brick”
that has been shipped to you, one of the wires
on the brick will be labeled as positive to
indicate which wire is connected to each
terminal.
 Connect the video cable to the camera.

Camera installed.
 After all the cameras have been installed we go to the
DVR to complete the power and video connections.
 KVM Installation and Connections (Optional)
 Now that the cameras have been assembled, mounted
and connected, the next portion of the installation will
be the cabling and setup of the digital video recorder or
DVR.
 To begin with the DVR is similar to a personal computer
and will require a keyboard, mouse and a monitor to
operate.. Most customers have a keyboard, mouse and
monitor that they are using with their current point-of-
sale (POS) system or they already have a PC that they are
working with. Due to space restrictions, we normally
install a KVM (Keyboard, Video, Mouse) switch that will
allow the customer to switch from the DVR to his
POS/PC system and use his current keyboard, mouse and
monitor to control and operate both the DVR and his
POS/PC system.
 The following explains how the systems are connected
using the KVM switch.
 Open the KVM Switch package and ensure you have the
following items available.
 KVM Switch
 2 Connection Cables
 Power Supply
 Select one of the KVM Cables and connect the Keyboard
(purple PS-2 type connector), Video (blue DB15
connector) and Mouse (green PS-2 connector) to the
appropriate ports on the PC2 side of the KVM switch.
 Connect the other end of the SAME cable to the
appropriate ports on the back of the DVR as shown
at the right.
 NOTE: Ensure the Video (DB15 connector) is plugged
into the Video port on the DVR motherboard NOT
one of the video ports on the video card.
 Connect the other KVM Cable to the appropriate ports on the
PC1 side of the KVM switch.
 Connect the other end of the SAME cable to the
appropriate ports on the back of the second computer
(POS system, PC system etc.) at the customer location.
 Connect to monitor cable to the Monitor port on the top edge of
the KVM switch.
 Connect the mouse and keyboard to the appropriate ports on the
bottom edge of the KVM switch.
 Connect the power supply to the power port on the bottom
edge of the KVM switch
With the KVM switch installed, you should be
able to hit the button on the top of the KVM
switch which will switch you from one system to
the other, and use his current keyboard, mouse
and monitor to control and operate both the
DVR and his POS/PC system.
 DVR Network Configuration
 When connecting to the cable/DSL modem there are
several things that we determine prior to
connecting the DVR to the network. This
information should have been provided to the
customer by the telecommunications company that
is providing the internet connection.
The following listing show what information is
required to continue the installation based on
the configuration of the customers network.
 When the customer is using a cable modem and
DHCP, connecting the DVR or the router directly to
the Cable Modem with some minor configuration
changes to either device is all that will be required.
When the Customer is using PPPoE and a DSL
Modem, the following information will be
required
Dynamic PPPoE
Username
Password
Static PPPoE
IP Address
 Subnet Mask
 Default Gateway IP
 DNS Server IPs
If the customer has been setup for Static IP we need
the following information in order to proceed.
 IP Address
 Subnet Mask
 Default Gateway IP
 DNS Server IPs
 Please note also that the customer needs to have the
following ports opened if the customers internal network
is protected by a firewall. Port 80, 4550, 5550, 6550, 7631
and 7632 are required to provide the remote access to the
surveillance system.
 Port 80 (TCP) is used to provide the DVR specific and
proprietary HTTP server that allows direct access to the
DVR for the HTML pages. These are the pages displayed
when the customer accesses the DVR directly by IP.
 Ports 4550 and 5550 are the command and data ports
that are required to provide the outgoing streaming
data for the video.
 Port 6550 is the audio port required to provide the outgoing
audio stream.
Two additional ports are required when the
customer needs remote access for
troubleshooting, maintenance and
operation of the DVR. Those ports at 7631 &
7632 and are designated as the PC
Anywhere access ports.
The ports must be opened and PC Anywhere
Host service must be installed and running in
the background on the DVR for the customer to
receive the Extended Warranty services.
 Option 1: Cable/DSL Modem connected straight to DVR.
 With only one computer utilizing the network connection
though the cable or DSL modem we can connect the DVR
directly to the modem utilizing the Ethernet cable.

 DVR network access configuration


DVR network access configuration
1. Click on START, then Settings, then Control Panel
2. Select Network and Dial-Up Connections
3. Double click on Local Area Connection
4. Click on Properties
5. Select Internet Protocol (TCP/IP) and then Properties.
If the customer has DHCP for his internet
connection, complete the following steps.
1. Select Obtain IP address automatically
2. Select Obtain DNS server address automatically
3. Select OK twice and close the window.
4.This completes the DVR network Configuration for the
LAN interface.
If the customer has a static IP address for
his internet connection, complete the
following steps.
If the customer has a static IP address for
his internet connection, complete the
following steps.
1. Select Use the following IP address and enter
the information obtained from the customer.
a. IP Address
b. Subnet Mask
c. Default Gateway
2. Select Use the following DNS server
addresses and enter the DNS server
information obtained from the customer.
3. Select OK twice and close the window.
4. This completes the DVR network
Configuration for the LAN interface.
 Option 2: Cable/DSL Modem connected through a router to the DVR.
 With multiple computers utilizing the network
connection though the cable or DSL modem we must
use a router to connect the DVR into the network. Each
device on the network must have its own IP to gain
access to the network. DHCP may be used for most
computers on the network, BUT the DVR must have a
dedicated or static IP to enable the remote access.
 The DVR uses several ports to provide remote access. Port 80
(TCP) is a 2-way port used to provide the DVR proprietary
HTTP server that allows direct access to the

 DVR for the HTML pages. These are the pages displayed
when the customer accesses the DVR directly by IP.reasons for
the static IP behind the router are
 The following process utilizes the D-Link DI-604 Ethernet
Broadband Router. The same process can
 Connect a Cat5/RJ45/Ethernet cable from the LAN port on the
DSL/cable modem to the WAN port on the router.
 Connect a cat5/RJ -45/Ethernet cable from any port on the
router to the LAN connection on the DVR.
 To configure the DI-604 router we will have to
configure the DVR to allow access to the router.
 Open Network Connections, then Local Area
Network configuration window.
 Select Internet Protocol (TCP/IP) and tProperties.
 Select Use the following IP address
 IP Address: 192.168.0.10
 Subnet Mask: 255.255.255.0
 Default Gateway: 192.168.0.1.
Select Use the following DNS server addresses
and enter the DNS server information obtained
from the customer.
 Select OK twice and close the window.

Open Internet Explorer and in
the location benter
http://192.168.0.1 and hit enter.

You should get the Enter Network
Pwindow as shown at the right.

Enter admin for the User Name
and leave The Password blank.

Click on the OK button
 Click on the Advanced tab on the top menu.
 Configure the router to show the following ports opened.
Remember to check the Enabled radio button as you enter
each to the port configurations. Click on the Apply button
after you have entered each port setup in the list below.

The next area that we must
configure is the router’s access to
the network through the Cable/DSL
modem. Click on the Home
tab on the top menu, and
then click on the WAN
button on the left menu. The
following page is displayed.
Select the WAN option that
will apply to the customer
network.

You might also like