Cea Convex 400 Manual

EN Operator’s manual READ CAREFULLY
CONVEX vision
3300 STEEL PRO - 4000 - 5000
SN - ZA xxxxxx
1020HA81J-EN-01/2016
CEA COSTRUZIONI ELETTROMECCANICHE ANNETTONI S.p.A.
C.so E. Filiberto, 27 - 23900 Lecco - Italy

Tel. ++39.0341.22322 - Fax ++39.0341.422646
Cas. Post. (P.O.BOX) 205
E-mail: [email protected] - web: www.ceaweld.com
EN ENGLISH
Introduction 2 Introduction
Description 2 Thank you for having purchased our product. Please read in-
structions on use in this manual as well as the safety rules
Operating features 2
given in the attached booklet and follow them carefully to get
Technical data 3 the best performance from the equipment and be sure that the
parts have the longest service life possible. This manual will
Usage limits (IEC 60974-1) 3 show you the best way to do any maintenance jobs or repairs
eventually needed by your equipment to resolve any eventu-
How to lift up the system 4
al problems, we do however recommend our customers to ar-
Opening the packaging 4 range to have maintenance and eventual repairs done at our
servicing centres as they have the right equipment and the
Installation and connections 4 highly qualified personnel is constantly updated. All our ma-
chinery and systems are subject to continual development.
Connection to the electrical supply 4
We must therefore reserve the right to modify their construc-
Usage norms 4 tion and properties.
MIG-MAG welding 5
Description
Spot welding 7
MULTI-FUNCTION INVERTER GENERATOR FOR MIG-MAG,
Interval welding 7 MMA, and TIG WELDING
Aluminium welding 7 The CONVEX vision series of multi-function equipments are
characterised by cutting edge, attractive design combined with
Electrode welding (MMA) 7 latest generation inverter technology and digital welding control.
Innovative, technologically advanced, robust, and easy to use,
TIG welding with “Lift” 8 they can be used for very high quality welding in MIG-MAG, us-
Maintenance 8 ing electrodes, and in TIG with “Lift” type ignition, and they rep-
resent the best solution for all industrial fields and all specialist
Optional 9 welding purposes that call for high precision and repeatable
results. CONVEX vision equipments, fitted with an innovative
The pointing out of any difficulties synergic digital control, colour display, and the extraordinary VI-
and their elimination 9 SION-ARC meet the needs of those that wish to combine syn-
ergy with complete control of all welding parameters.
Replacing the digital interface PCB 9 They come in a version with a separate feeder (HT5).
Wiring diagram 10 These are systems open to the future evolution of technology -
the control software can be kept up to date with the latest ver-
Key to the electrical diagram 11 sions with the help of a personal computer.
Colour key 11
Operating features
Meaning of graphic symbols on machine 12
The main feature of the welding unit CONVEX vision 3300
STEEL PRO - 4000 - 5000 are:
• Metallic main structure with shockproof plastic front frames.
• Controls protected by a visor.
• Exceptional characteristics for MIG-MAG, MMA, and TIG
welding with “Lift” type ignition.
• Synergic digital control (VS) of all welding parameters, dis-
played via the innovative colour display, also featuring the
following functions:
- Allows less expert operators to regulate all welding param-
eters in a user-friendly way and extremely easily, choos-
ing the type of program on the basis of the material, wire
diameter, and gas used.
- Innovative “VISION ARC” software for controlling all weld-
ing parameters.
- With the special MIG torches you can adjust the welding
parameters at a distance straight from the torch.
- BURN BACK control. At the end of each weld, in any con-
dition and with any material, the digital control ensures a
perfect wire cut, prevents the typical “wire globule” from
forming and ensures correct arc restriking.
- WSC Wire start control. This arc striking control device pre-
vents wire from sticking to the workpiece or torch nozzle
and ensures precise and smooth arc striking, particularly
when welding aluminium.
2
- Welding parameters and short-circuits that are controlled Technical data
digitally by a microprocessor, are monitored and modified
in just a few seconds, maintaining a consistently precise The general technical data of the system are summarized in
and stable arc as the welding conditions continue to vary table 1.
due to the movement of the torch and the irregularities of
the parts to be welded.
- Exclusive SWS “Smart Welding Stop” system at the end of Usage limits (IEC 60974-1)
TIG welding. Lifting up the torch without switching off the
arc will introduce a slope down and it will switch off auto- The use of a welder is typically discontinuous, in that it is made
matically. up of effective work periods (welding) and rest periods (for the
- “Energy Saving” function to operate the power source cool- positioning of parts, the replacement of wire and underflush-
ing fan and the torch water cooling only when necessary. ing operations etc. This welder is dimensioned to supply a I2
- Auto-diagnostic feature for trouble shooting. max nominal current in complete safety for a period of work of
- Password-controlled total or partial equipment access. 40/50% of the total usage time. The regulations in force estab-
• High electrical performance resulting in a reduction in ener- lish the total usage time to be 10 minutes. The work cycle is
gy consumption. considered to be 40/50% of this period of time. Exceeding the
• Remote parameter adjustment directly from HT5 feeder. work cycle allowed could cause a trip switch to trip (for further
information see the VS control panel manual), which protects
the components inside the welding machine against dangerous
overheating. After several minutes the overheat cut-off rearms
automatically and the welder is ready for use again.
Table 1
CONVEX vision CONVEX vision CONVEX vision
Model STEEL PRO 3300 4000 5000
MIG-MAG welding
Three-phase input 50/60 Hz V 400 ± 20% 400 ± 20% 400 ± 20%
Mains supply: Zmax Ω 0,037 0,028 0,017
Input power @ I2 Max kVA 15,2 19,4 26,3
Delayed fuse (I2 @ 60%) A 20 25 35
Power factor / cosφ 0,86 / 0,99 0,9 / 0,99 0,94 / 0,99
Efficiency degree η 0,82 0,88 0,89
Open circuit voltage V 63 70 70
Current range A 10 ÷ 330 10 ÷ 400 10 ÷ 500
Duty cycle @ 100% (40°C) A 280 310 380
Duty cycle @ 60% (40°C) A 300 370 460
Duty cycle @ X% (40°C) A 330 (40%) 400 (50%) 500 (50%)
Wires diameter (*) mm 0,6 ÷ 1,2 (*) 0,6 ÷ 1,6 (*) 0,6 ÷ 2,0 (*)
N° rollers (*) 4 (*) 4 (*) 4 (*)
Power output of feeder motor (*) W 100 (*) 100 (*) 100 (*)
Rated wire feeding speed (*) m/min 0,5 ÷ 25 (*) 0,5 ÷ 25 (*) 0,5 ÷ 25 (*)
Spool (*)
Diameter mm Ø300 (*) Ø300 (*) Ø300 (*)
Weight kg 15 (*) 15 (*) 15 (*)
IEC 60974-1 - IEC 60974-5 (*) - IEC 60974-10
Standards
Protection class IP 23 S IP 23 S IP 23 S
Insulation class H H H
Dimensions mm 660 - 515 - 290 660 - 515 - 290 660 - 515 - 290
Weight kg 35 39 43
(*) On the HT5 feeder, fitted separately.
WARNING: This equipment complies with EN//IEC 61000-3-12 provided that the maximum permissible system impedance Zmax is less than or
equal to 0,037 Ω CONVEX vision 3300 STEEL PRO - 0,028 Ω CONVEX vision 4000 - 0,017 Ω CONVEX vision 5000 at the interface point be-
tween the user’s supply and the public system. It is the responsibility of the installer or user of the equipment to ensure, by consultation with the
distribution network operator if necessary, that the equipment is connected only to a supply with maximum permissible system impedance Zmax
less than or equal to 0,037 Ω CONVEX vision 3300 STEEL PRO - 0,028 Ω CONVEX vision 4000 - 0,017 Ω CONVEX vision 5000.
This system, tested according to EN/IEC 61000-3-3, meets the requirements of EN/IEC 61000-3-11.
3
How to lift up the system This system is cooled by means of the forced circulation of air,
and must therefore be placed in such a way that the air may
Strap the system safely and securely in the slings working from be easily sucked in and expelled through the apertures made
the bottom, then lift up from the ground. in the frame.
This welding machine has a robust handle built into the frame Assemble the system in the following way:
for moving the equipment. • Assemble the trolley.
• Fixing the cooling unit to the trolley.
NOTE: These hoisting and transportation devices conform to • Fixing of the welding machine to the trolley and the cooling
European standards. Do not use other hoisting and transpor- unit (electrical and plumbing connections).
tation systems. • Fitting the feeder unit to the generator.
• Connect up the welder to the mains.
Opening the packaging • Connect up the wire-feeder/generator interconnection cable.
• Connect up the welding cables.
The system essentially consists of: Instructions for fitting the individual components / optional ex-
• CONVEX vision 3300 STEEL PRO - 4000 - 5000 weld unit. tras are contained in the relevant packaging.
• Separately:
- HT5 wire-feeder unit (supplied separately). Connection to the electrical supply
- MIG-MAG welding torch (optional).
- Wire-feeder/generator interconnection cable (supplied sep- Connection of the machine to the user line (electrical cur-
arately). rent) must be performed by qualified personnel.
- Coolant unit for welding torch (optional). Before connecting the welding machine to the mains pow-
- Trolley to carry it around (optional). er supply, make sure that rated voltage and frequency cor-
Perform the following operations on receiving the apparatus: respond to those provided by the mains power supply and
• Remove the welding generator and all accessories and com- that the welding machine’s power switch is turned to “O”.
ponents from the packaging. Use the welder’s own plug to connect it up to the main pow-
• Check that the welding apparatus is in good condition; other- er supply. Proceed as follows if you have to replace the plug:
wise immediately inform the retailer or distributor. • 3 conducting wires are needed for connecting the machine
• Check that all the ventilation grilles are open and that there to the supply.
is nothing to obstruct the correct air flow. • The fourth, which is YELLOW GREEN in colour is used for
making the “GROUND” connection.
Installation and connections Connect a suitable load of normalised plug (3P+T) to the
power cable and provide for an electrical socket complete
The installation site for the system must be carefully chosen with fuses or an automatic switch. The ground terminal
in order to ensure its satisfactory and safe use. The user is re- must be connected to the ground conducting wire (YEL-
sponsible for the installation and use of the system in accord- LOW-GREEN) of the supply.
ance with the producer’s instructions contained in this manual. Table 2 shows the capacity values that are recommended for
Before installing the system the user must take into consider- fuses in the line with delays.
ation the potential electromagnetic problems in the work area. NOTE: Any extensions to the power cable must be of a suita-
In particular, we suggest that you should avoid installing the ble diameter, and absolutely not of a smaller diameter than the
system close to: special cable supplied with the machine.
• Signalling, control and telephone cables.
• Radio and television transmitters and receivers.
• Computers and control and measurement instruments. Usage norms
• Security and protection instruments.
Persons fitted with pace-makers, hearing aids and similar CONTROL APPARATUS (Fig. A)
equipment must consult their doctor before going near a ma- Pos. 1 “VS” control panel.
chine in operation. The equipment’s installation environment Pos. 2 Fast coupling positive polarity.
must comply to the protection level of the frame. Pos. 3 Fast coupling negative polarity.
The welding unit is characterized by the following classes: Pos. 4 Power supply switch. In the “O” position the welder
• IP 23 S protection class indicates that the generator can be is off.
used in both interior and exterior environments. Pos. 5 Connector for connecting the interconnection cable
• The “S” usage class indicates that the generator can be em- or auxiliary welding controls.
ployed in environments with a high risk of electrical shocks. Pos. 6 Fast coupling reverse polarity.
Pos. 7 Connector for connecting the cooling system.
Pos. 8 Mains cable.
Table 2
CONVEX vision CONVEX vision CONVEX vision
Model STEEL PRO 3300 4000 5000
MIG-MAG welding
Input power @ I2 Max V 15,2 19,4 26,3
Delayed fuse (I2 @ 60%) Ω 20 25 35
Duty cycle @ X% (40°C) kVA 330 (40%) 400 (50%) 500 (50%)
Mains cable
Length mm 4 4,5 4,5
Section kg 4 × 2,5 4×4 4×6
Ground cable kg 50 50 70
4
4
1
2
3 8 7 6 5
FIG. A
MIG-MAG welding 2A - Connecting the cables - Welding with a POSITIVE

POLE TORCH (Fig. B1)
To begin MIG-MAG welding, carry out the following tasks (with 1) The feeder - generator connecting cable is used to connect
the machine switched off). the welding machine to the feeder.
WARNING: Do not disconnect the wire-feeder until the ma-
1 - Connecting the gas hose and torch (Fig. B1-B2) chine has been switched off.
• Connect the gas hose to the pressure reducer fitted on the
cylinder beforehand. Connect up the interconnection cables (power cable, an-
• Screw the torch onto the centralised connection on the front cillary wiring and gas tube) to the special attachments and
panel of the feeder and connect the feed (blue) and return couplings shown in Fig. B1.
(red) water hoses for cooling the torch to the respective (blue
and red) rapid couplings on the front panel of the feeder.
BLACK
RED BLUE
BLUE
RED
BLUE
RED
BLACK
FIG. B1 2000FB62
5
BLACK
RED BLUE
BLUE
RED
BLUE
RED
BLACK
FIG. B2 2000FB63
The delivery (blue coloured) and return (red coloured) wa- 2) Connect up the earthing system cable to the rapid cou-
ter tubes, used for cooling the torch of the welding machine, pling marked by a + (positive) symbol and then the relevant
are part of the interconnection cable and should be con- ground clamps to the piece being welded or to its support in
nected as follows: an area free from rust, paint and grease. Using particularly
• Interconnection cable on generator side: connect up long earthing cables reduces the voltage and causes some
tubes to their rapid couplings (blue and red coloured) at problems from increased resistance and inductance of the
the back of the coolant system. cables that could cause faulty welding. Follow instructions
• Wire feeder side connecting cable: connect the red and to avoid these problems:
blue pipes to their respective bulkhead grommets on the • Use earthing and extension cables with appropriate sec-
rear panel of the feeder. tion.
2) Connect up the earthing system cable to the rapid cou- • Lay out the cables as a flat as possible to prevent them
pling marked by a - (negative) symbol and then the rel- from coiling up.
evant ground clamps to the piece being welded or to its
support in an area free from rust, paint and grease. Using 3 - Welding
particularly long earthing cables reduces the voltage and 1) Switch the welding machine on by moving the power sup-
causes some problems from increased resistance and in- ply switch to I (Pos. 4, Fig. A).
ductance of the cables that could cause faulty welding. Fol- 2) Make the adjustments and do the parameter settings on
low instructions to avoid these problems: the control panel (for further information see the VS con-
• Use earthing and extension cables with appropriate sec- trol panel manual).
tion. 3) Load the wire (see the relevant paragraph in the feeder
• Lay out the cables as a flat as possible to prevent them manual) using the motor test button, after having removed
from coiling up. the wire guide nozzle from the torch to allow the wire to
come out freely during loading (remember that the wire
2B - Connecting the cables - Welding with a guide nozzle must correspond to the diameter of the wire
NEGATIVE POLE TORCH (Fig. B2) used).
1) Connect the generator - feeder connection cable using the 4) Open the tap on the cylinder slowly and adjust the reduc-
extension cable in addition to invert the polarity (optional). er knob to obtain a pressure of about 1,3 to 1,7 bar, and
then activate the gas test button and regulate the flow to
WARNING: Do not disconnect the wire-feeder until the ma-
a value between 14 and 20 lit/min to suit the current used
chine has been switched off.
for welding.
Connect up the interconnection cables (power cable, an- 5) The welding machine is ready to weld. Make the adjust-
cillary wiring and gas tube) to the special attachments and ments and select the parameters for the feeder or, if se-
couplings shown in Fig. B2. lected, on the control panel (for further information see the
The delivery (blue coloured) and return (red coloured) wa- VS control panel manual). Start welding by moving close
ter tubes, used for cooling the torch of the welding machine, to the welding point and press the torch button.
are part of the interconnection cable and should be con- 6) Once welding has been completed remove any slag, switch
nected as follows: off the machine (which is only to be done when the fan is
• Interconnection cable on generator side: connect up not running), and close the gas cylinder.
tubes to their rapid couplings (blue and red coloured) at
the back of the coolant system.
• Wire feeder side connecting cable: connect the red and
blue pipes to their respective bulkhead grommets on the
rear panel of the feeder.
6
Spot welding
The substantial difference with MIG-MAG welding is essential-
ly related to the torch and the adjustments that must be made
on the VS control panel.
• The gas guide nozzle specifically for spot welding must be
fitted on the torch (see Fig. C).
• On the VS control panel, select the spot welding mode and
set the time.
To begin spot welding:
• Press the torch button to start the welding current and wire
feed.
• When the spot welding time expires, the wire feed stops au-
tomatically.
2000HB64
• When the torch button is pushed again a new welding cy-
cle starts.
• Release the torch button.
FIG. D
FIG. C
Interval welding
The basic difference from spot welding is the addition of an ad-
ditional time known as the “stitch pause”.
On the VS control panel, select the interval welding mode and
then set the following times for it:
• Stitch time.
• Stitch pause.
To begin interval welding:
2000HB65
• Press the torch button to start the welding current and wire
feed.
• At this point the welding machine automatically carries out a FIG. E
succession of welded portions followed by a pause, accord-
ing to the times entered previously. This procedure stops au-
tomatically only when the torch button is released.
• When the torch button is pushed again the torch begins a
new interval welding cycle. type of electrode being used (Fig.D). Always follow the
electrode manufacturer’s instructions. The welding cables
must be as short as possible, they must be near to one
Aluminium welding another, positioned at or near floor level. Do not touch the
electrode clamp and the ground clamp simultaneously.
To weld with aluminum wire proceed as follows: 2) Switch the welding machine on by moving the power sup-
• Replace the drive rolls with special ones for aluminium wire. ply switch to I (Pos. 4, Fig. A).
• Use a torch with a 3M cable and a carbon Teflon sheath. 3) Make the adjustments and do the parameter settings on
• Set the pressure between the drive rollers at the minimum, the control panel (for further information see the VS con-
by turning the screw provided. trol panel manual).
• Use argon gas at a pressure of 1,3 - 1,7 bar and regulate 4) Carry out welding by moving the torch to the workpiece.
the flow to a value between 14 and 20 lit/min to suit the cur- Strike the arc (press the electrode quickly against the met-
rent used for welding. al and then lift it) to melt the electrode, the coating of which
forms a protective residue. Then continue welding at an in-
Electrode welding (MMA) clination of about 60° compared with the metal in relation
to the direction of welding.
On the CONVEX vision 3300 STEEL PRO - 4000 - 5000 ma-
chine, electrode welding is used to weld most metals (different PART TO BE WELDED
types of steel, etc.) using coated rutilic and basic electrodes The part to be welded must always be connected to ground
with diameters ranging from Ø 1.6 mm to Ø 6 mm, and devic- in order to reduce electromagnetic emission. Much attention
es that the user can adjust for “Arc Force”, “Hot Start”, and An- must be afforded so that the ground connection of the part to
ti-sticking functions to avoid the electrodes sticking. be welded does not increase the risk of accident to the user or
1) Connecting the welding cables (Fig. D): the risk of damage to other electric equipment. When it is nec-
Disconnect the machine from the mains power supply and essary to connect the part to be welded to ground, you should
connect the welding cables to the output terminals (Posi- make a direct connection between the part and the ground
tive and Negative) of the welding machine, attaching them shaft. In those countries in which such a connection is not al-
to the clamp and ground with the polarity specified for the lowed, connect the part to be welded to ground using suitable
capacitors, in compliance with the national regulations.
7
WELDING PARAMETERS 2) Switch the welding machine on by moving the power sup-
Table 3 shows some general indications for the choice of elec- ply switch to I (Pos. 4, Fig. A).
trode, based on the thickness of the parts to be welded. The 3) Make the adjustments and do the parameter settings on
values of current to use are shown in the table with the respec- the control panel (for further information see the VS con-
tive electrodes for the welding of common steels and low-grade trol panel manual).
alloys. These data have no absolute value and are indicative 4) Open the gas cylinder and regulate the flow by adjusting
data only. For a precise choice follow the instructions provided the valve on the TIG torch by hand.
by the electrode manufacturer. 5) Ignite the electric arc by contact, using a decisive, quick
movement without dragging the tungsten electrode on the
Table 3 piece to be welded (“Lift” type ignition).
Welding thickness (mm) Ø electrode (mm) 6) The welder has a SWS “Smart Welding Stop” system for
1,2 ÷ 2 1,6 the end of TIG welding. Lifting up the torch without switch-
1,5 ÷ 3 2 ing off the arc will introduce a slope down and it will switch
3÷5 2,5 off automatically.
5 ÷ 12 3,25 7) When you have finished welding remember to shut the
≥ 12 4 valve on the gas cylinder.
≥ 20 ≥5 Table 5 shows the currents to use with the respective elec-
trodes for TIG DC welding. This input is not absolute but is for
Table 4 your guidance only; read the electrode manufacturers’ instruc-
tions for a specific choice. The diameter of the electrode to use
Ø electrode (mm) Current (A) is directly proportional to the current being used for welding.
1,6 30 ÷ 60
2 40 ÷ 75 Table 5
2,5 60 ÷ 110 ELECTRODE TYPE
3,25 95 ÷ 140 Current adjustment field (A)
4 140 ÷ 190
Ø ELECTRODE TIG DC
5 190 ÷ 240
(mm) Tungsten Tungsten
6 220 ÷ 330
Ce 1% Rare ground 2%
The current to be used depends on the welding positions and Grey Turchoise
the type of joint, and it increases according to the thickness and 1 10-50 10-50
dimensions of the part.
1,6 50-80 50-80
The current intensity to be used for the different types of weld-
ing, within the field of regulation shown in table 4 is: 2,4 80-150 80-150
• High for plane, frontal plane and vertical upwards welding. 3,2 150-250 150-250
• Medium for overhead welding. 4 200-400 200-400
• Low for vertical downwards welding and for joining small pre-
heated pieces.
A fairly approximate indication of the average current to use in Maintenance
the welding of electrodes for ordinary steel is given by the fol-
lowing formula: ATTENTION: Cut off the power supply to the equipment be-
I = 50 × (Øe - 1) fore effecting any internal inspection.
Where:
I = intensity of the welding current CONVEX vision 3300 STEEL PRO - 4000 - 5000
Øe = electrode diameter IMPORTANT: For fully electronic welding machines, remov-
Example: ing the dust by sucking it into the machine by the fans, is of ut-
For electrode diameter 4 mm most importance.
I = 50 × (4 - 1) = 50 × 3 = 150A In order to achieve correct functioning of the machine, pro-
ceed as described:
• Periodic removal of accumulations of dirt and dust inside the
TIG welding with “Lift” equipment using compressed air. Do not point the jet of air
In the TIG process welding is achieved by melting the two metal directly at the electrical parts as this could damage them.
pieces to be joined, with the possible addition of material from • Periodical inspection for worn cables or loose connections
the outside, using an arc ignited by a tungsten electrode. The that could cause overheating.
“Lift” type ignition used in CONVEX equipments makes it pos- TORCH
sible to reduce tungsten inclusions on ignition to a minimum. The torch is subjected to high temperatures and is also stressed
The molten bath and the electrode are protected by and inert by traction and torsion. We recommend not to twist the wire and
gas (for example, Argon). This type of welding is used to weld not to use the torch to pull the welder. As a result of the above
thin sheet metal or when elevated quality is required. the torch will require frequent maintenance such as:
1) Connecting the welding cables (Fig. E): • Cleaning welding splashes from the gas diffuser so that the
• Connect one end of the gas hose to the gas connecter on gas flows freely.
the TIG torch and the other end to the pressure reducer • Substitution of the contact point when the hole is deformed.
on the inert gas cylinder (Argon or similar). • Cleaning of the wire guide liner using trichloroethylene or
• With the machine switched off: specific solvents.
- Connect the ground cable to the snap-on connector • Check of the insulation and connections of the power cable;
marked + (positive). the connections must be in good electrical and mechanical
- Connect the relative ground clamp to the workpiece or condition.
to the workpiece support in an area free of rust, paint,
grease, etc.. SPARE PARTS
- Connect the TIG torch power cable to the snap-on con- Original spares have been specifically designed for our equip-
nector marked - (negative). ment. The use of spares that are not original may cause vari-
ations in the performance and reduce the safety level of the
equipment. We are not liable for damage due to use of spare
parts that are not original.
8
Optional
NOTE: The digital control unit of the generator is fitted with a
control recognition device which allows it to identify which de-
vice is connected and take action accordingly.
REMOTE CONTROL ANALOGIC RC

This command (that must be plugged into the relevant connec-
tor on the front panel of the HT5 drawing unit):
• Completely replaces the ENCODER - A knob on the HT5
feeder’s front panel.
• Partially (depending on the welding process selected) replac-
es the ENCODER - V knob on the HT5 feeder’s front pan-
el (for further information see the VS control panel manual).
AIR AND/OR WATER COOLED UP/DOWN TORCH
This command (that must be plugged into the relevant con-
nector on the front panel of the HT5 drawing unit) works as an
alternative to:
• The ENCODER - A knob on the HT5 feeder’s front panel. In
“synergic” MIG MAG and “manual” MIG MAG welding pro-
cesses, by pressing the two right (+) and left (-) buttons you
can regulate the values for the synergic welding parameters.
• The ENCODER - V knob on the HT5 feeder’s front panel. In
the JOB welding process, by pressing the two right (+) and
left (-) buttons you can scroll the welding points set previ-
ously.
PUSH-PULL TORCH
The push-pull torch makes it possible to improve the alumini-
um wire feed, using the motor on the torch itself. The param-
eters normally regulated using the ENCODER - SX knob on
the welding machine’s VS control panel, are now regulated us-
ing the potentiometer on the torch itself, when this torch is on.
The pointing out of any difficulties

and their elimination
The supply line is attributed with the cause of the most com-
mon difficulties. In the case of breakdown, proceed as follows:
1) Check the value of the supply voltage.
2) Check that the power cable is perfectly connected to the
plug and the supply switch.
3) Check that the power fuses are not burned out or loose.
4) Check whether the following are defective:
• The switch that supplies the machine
• The plug socket in the wall
• The generator switch
NOTE: Given the required technical skills necessary for the re-
pair of the generator, in case of breakdown we advise you to
contact skilled personnel or our technical service department.
Replacing the digital interface PCB

Proceed as follows:
• Unscrew the 4 screws fastening the front rack panel.
• Remove both the adjustment knobs.
• Extract wiring connectors from digital interface PCB.
• Unscrew the nuts and washers on the support.
• Remove the digital interface PCB by lifting it out of its sup-
ports.
• Proceed vice versa to assemble the new digital interface
PCB.
9
Wiring diagram
2101EA34
10
Key to the electrical diagram
•1 •2 •3 •4 •5
C2 CCI CHR Cp D2
•6 •7 •8 •9 •10
F-EMC IL L2 MIH MIL
•11 •12 •13 •14 •15
MV1-2 P1 P2 R2 RP
•16 •17 •18 •19
RS S-INT DIG S-INV S-PS
•20 •21 •22 •23
TA TH2 TP VR
•1 SNUBBER capacitor for output diodes •2 Interconnection cable con-
nector •3 Power supply connector for the cooling system •4 Quick con-
nection protection capacitor •5 Secondary diode •6 EMC filter •7 Power
supply switch •8 Secondary inductor •9 Primary upper IGBT module
•10 Lower primary IGBT module •11 Fan motor •12 Main primary trans-
former (start) •13 Main primary transformer (end) •14 Output diode
snubber resistor •15 Primary rectifier •16 Secondary rectifier •17 Digi-
tal interface PCB •18 Inverter PCB •19 Power Source PCB •20 Hall ef-
fect transformer •21 Secondary thermostat •22 Main transformer •23
Output diodes snubber varistor
Colour key
Ar Orange
Az Sky Blue
Bc White
Bl Blue
Gg Grey
Gl Yellow
GV Yellow-Green
Mr Brown
NA Black-Sky Blue
Nr Black
RN Red-Black
Ro Pink
Rs Red
Vd Green
Vl Violet
11
Meaning of graphic symbols on machine
Power supply switch Positive pole snap-in connector
System for use in environments with in- Negative pole snap-in connector
creased risk of electroshock
Product suitable for free circulation in the Warning!

European Community
Before using the equipment you should

Danger! high voltage carefully read the instructions included in
this manual
Grounding Special disposal
12
IT Lista ricambi LEGGERE ATTENTAMENTE
CONVEX vision EN Spare parts list READ CAREFULLY
3300 STEEL PRO - 4000 - 5000

Tel. ++39.0341.22322 - Fax ++39.0341.422646
IT Lista ricambi (CONVEX vision 3300 STEEL PRO) EN Spare parts list (CONVEX vision 3300 STEEL PRO)
3
4
5
6
10
CONVEX vision
Pos. Descrizione Description
3300 STEEL PRO
1 352389 Pivot Pivot
2 352461 Visiera rack frontale Front rack visor
Pannello rack, con adesivo Rack panel with "CONVEX"
3 439395
"CONVEX", senza display sticker without display
4 378020 Display Display
5 438849 Manopola senza indice Ø22mm Ø22mm Knob without index
6 438888 Manopola senza indice Ø29mm Ø29mm Knob without index
7 468725 Adesivo logo CEA Ø30mm CEA logo sticker Ø30mm
Pannello frontale senza adesivo
8 352458 Front panel without CEA logo sticker Ø30mm
logo CEA Ø30mm
9 403611 Attacco rapido Quick connection
10 420685 Coperchio lato sinistro con adesivo logo CEA Left cover with CEA logo sticker
2
11
12
13
14
15
16
20
19 18 17
CONVEX vision
3300 STEEL PRO
11 420577 Coperchio superiore Top cover
12 438111 Maniglia Handle
13 438720 Manopola interruttore alimentazione Mains switch knob
14 427883 Pressacavo con ghiera Cable clamp with lock ring
15 235948 Cavo alimentazione Mains cable
Pannello posteriore senza
16 352459 Rear panel without CEA logo sticker Ø30mm
adesivo logo CEA Ø30mm
17 453145 Connettore cavo interconnessione Interconnection cable connector
18 403611 Attacco rapido Quick connection
Connettore alimentazione
19 419049 Cooling system power connector
impianto di raffreddamento
20 420686 Coperchio lato destro con adesivo logo CEA Right cover with CEA logo sticker
3
21 22 23 25 26
27
28
40
39
29
38
30
37
36 35 34 33 32 31
41
42
CONVEX vision
3300 STEEL PRO
21 435760 Interruttore alimentazione Mains switch
22 427667 Filtro EMC EMC Filter
23 449578 Pianale superiore Upper plate
25 478786 Termostato secondario Secondary thermostat
26 377113 Scheda power source Power source PCB
27 413499 Cablaggio ausiliario Auxiliary wiring
28 463215 Staffa fissaggio trasformatore Transformer support
29 481424 Trasformatore principale Main transformer
30 481954 Trasformatore ad effetto di Hall Hall effect transformer
31 418874 Condensatore di protezione attacco rapido Quick connection protection capacitor
32 247494 Induttore secondario Secondary inductor
33 404931 Basamento Base
34 478846 Termostato primario Primary thermostat
35 286019 IGBT primario Primary IGBT
36 240474 Complessivo inverter primario Primary inverter assembly
37 455512 Raddrizzatore primario Primary rectifier
38 486379 Motore ventilatore Fan motor
39 377105 Scheda di snubber secondaria Snubber secondary PCB
40 423236 Diodo secondario Secondary diode
41 377149P Scheda interfaccia digitale Digital Interface PCB
42 454150 Encoder Encoder
4
IT Lista ricambi (CONVEX vision 4000-5000) EN Spare parts list (CONVEX vision 4000-5000)
3
4
5
6
10
CONVEX CONVEX
vision 4000 vision 5000
1 352389 352389 Pivot Pivot
2 352461 352461 Visiera rack frontale Front rack visor
Pannello rack, con adesivo Rack panel with "CONVEX"
3 439373 439374
"CONVEX", senza display sticker without display
4 378020 378020 Display Display
5 438849 438849 Manopola senza indice Ø22mm Ø22mm Knob without index
6 438888 438888 Manopola senza indice Ø29mm Ø29mm Knob without index
7 468725 468725 Adesivo logo CEA Ø30mm CEA logo sticker Ø30mm
Pannello frontale senza adesivo
8 352458 352458 Front panel without CEA logo sticker Ø30mm
logo CEA Ø30mm
9 403617 403617 Attacco rapido Quick connection
10 420685 420685 Coperchio lato sinistro con adesivo logo CEA Left cover with CEA logo sticker
5
11
12
13
14
15
16
20
19 18 17
CONVEX CONVEX
11 420577 420577 Coperchio superiore Top cover
12 438111 438111 Maniglia Handle
13 438720 438720 Manopola interruttore alimentazione Mains switch knob
14 427883 427883 Pressacavo con ghiera Cable clamp with lock ring
15 235999 235943 Cavo alimentazione Mains cable
Pannello posteriore senza
16 352459 352459 Rear panel without CEA logo sticker Ø30mm
adesivo logo CEA Ø30mm
17 453145 453145 Connettore cavo interconnessione Interconnection cable connector
18 403617 403617 Attacco rapido Quick connection
Connettore alimentazione
19 419049 419049 Cooling system power connector
impianto di raffreddamento
20 420686 420686 Coperchio lato destro con adesivo logo CEA Right cover with CEA logo sticker
6
27
26
25
23 22
24
21
CONVEX CONVEX
21 404931 404931 Basamento Base
22 286034 286042 IGBT primario Primary IGBT
23 455508 455508 Raddrizzatore primario Primary rectifier
24 240466 240468 Complessivo inverter primario Primary inverter assembly
25 449578 449578 Pianale superiore Upper plate
26 427667 427667 Filtro EMC EMC Filter
27 435760 435760 Interruttore alimentazione Mains switch
7
EN Operator’s manual READ CAREFULLY
DH / VS
32 • 33 • 40 • 50

Tel. ++39.0341.22322 - Fax ++39.0341.422646
EN ENGLISH
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Welding machine control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Wire feeder control panel (not used with DH 32 and VS 32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

WELDING MODE SELECTION Key (not used with DH 32 and VS 32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Switching on the welding machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Language selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Screen saver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
WELDING PROCESS SELECTION Menu (PROCESS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
MIG-MAG, MIG pulse/dual pulse (Vision.PIPE, Vision.COLD, Vision.POWER, Vision.ULTRASPEED only if activated) . 8
1 - PROGRAM SELECTION Menu (PROGRAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 - WELDING MODE SELECTION Menu (MODE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 - SPECIAL FUNCTIONS Menu (SET UP Fx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 - PRE-SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5 - WELDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6 - HOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7 - WIRE LOADING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8 - DOUBLE FEEDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1 - PROGRAM SELECTION Menu (PROGRAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2 - SPECIAL FUNCTIONS Menu (SET UP Fx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3 - PRE-SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4 - WELDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5 - HOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6 - ACTIVATING THE VRD DEVICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
TIG LIFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1 - SPECIAL FUNCTIONS Menu (SET UP Fx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2 - PRE-SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3 - WELDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4 - HOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
JOB/SEQUENCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1 - Creating and saving / editing and overwriting a JOB/SEQUENCES (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2 - JOB/SEQUENCES SELECTION Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3 - PRE-SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4 - WELDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5 - HOLD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2
Error condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
SETUP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
JOB EDIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SEQ EDIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
PASSWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
BLOCKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
CONFIG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FACTORY RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
INFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
NETWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
ERROR LOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
ADVANCED SETUP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

ADVANCED CONFIG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
ADVANCED MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
EQUIPMENT LAYOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
WELD LOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
3
Introduction
This manual describes the functions of the software operating the following control panels:
• DH 32 VS 32
• DH 33 + HT5 VS 33 + HT5
• DH 40 + HT5 VS 40 + HT5
• DH 50 + HT5 VS 50 + HT5
Functioning of the panels listed above is identical (the functions are the same but the characteristics differ depending on the type
of machine they are fitted on (e.g.: current regulation field).
General notes
• Any adjustments/changes made on the welder control panel are also displayed automatically on the drag-and-drop
control panel and vice versa, the images on the displays of both weld system components could however differ one
from the other, as the displays are consistent with adjustments/changes but also independent as far as visualization
is concerned.
• The adjustments / changes made are immediately available to the operator, unless indicated otherwise in the manual.
Welding machine control panel

The panel on the generator has four keys, two encoders, and a colour display. The figure below shows the panel. The figure be-
low shows the image of the panel.
MENU KEY ENTER/MEM KEY
SX KEY DX KEY
ENCODER KNOB - SX ENCODER KNOB - DX
VISION SCREEN
“DH” / “VS” CONTROL PANEL
Wire feeder control panel (not used with DH 32 and VS 32)

The HT5 wire feeder panel has 2 keys, 2 encoders and 7 LEDs in the upper section and 4 keys and 5 LEDs in the lower section.
The figure below shows the panel. The figure below shows the image of the panel.
PARAMETER DISPLAY SCREEN - A HOLD Function LED
PARAMETER SELECTION LED - A PARAMETER DISPLAY SCREEN - V

PARAMETER SELECTION LED - V
PARAMETER SELECTION KEY - A
PARAMETER SELECTION KEY - V
ENCODER KNOB - A
ENCODER KNOB - V
WIRE KEY
GAS KEY
WELDING MODE SELECTION KEY SPECIAL FUNCTIONS (FX) KEY
WELDING MODE SELECTION LED SPECIAL FUNCTIONS (FX) LED
“HT5” CONTROL PANEL
4
WELDING MODE SELECTION Key (not used with DH 32 and VS 32)
Each time this is pushed the following welding modes can be selected (only for pulsed and double pulsed MIG, synergic and
manual welding processes) on the feeder (on the welding machine the welding mode is selected using a specific menu - see the
appropriate paragraphs) according to a specific sequence:
2T LED
4T LED
WELDING MODE SELECTION LED
CRATER LED
SPOT LED
TWO STROKE (2T) 2T LED ( ) switched on

Pressing the TORCH TRIGGER starts the welding cycle, which will stop when it is released.
FOUR STROKE (4T) 4T LED ( ) switched on
1) Pressing and releasing the TORCH TRIGGER will start the welding cycle.
2) Pressing and releasing the TORCH TRIGGER will stop the welding cycle.
CRATER 2T 2T LED ( ) switched on - CRATER LED ( ) switched on
1) When the TORCH TRIGGER is pushed the arc ignites and the parameters assume the values for the “initial crater” for a time
set by means of the INITIAL CRATER DURATION (F10) function.
After that the parameter values become those for “welding” for a time defined by the INITIAL SLOPE (F11) function.
2) When the TORCH TRIGGER is released the parameters take on the “final crater” values for a time set by means of the FINAL
CRATER TIME (F15) function, for a period of time set using the FINAL SLOPE (F12) function.
CRATER 4T 4T LED ( ) switched on - CRATER LED ( ) switched on
1) When the TORCH TRIGGER is pushed the arc ignites and the parameters assume the values for the “initial crater”.
2) When the TORCH TRIGGER is released the parameters take on the “welding” values for a time set using the INITIAL SLOPE
(F11) function.
3) When the TORCH TRIGGER is pushed again the parameters take on the “final crater” values for a time defined using the
FINAL SLOPE (F12) function.
4) Releasing the TORCH TRIGGER will end the welding cycle.
SPOT WELDING 2T LED ( ) switched on - SPOT LED ( ) switched on
This is used so that on pressing the TORCH TRIGGER spot welding is done for a time period set beforehand (in seconds), after
which the arc switches off automatically.
STITCH WELDING 2T LED ( ) switched on - SPOT LED ( ) flashing
To begin stitch welding:
1) Press the TORCH TRIGGER to start the welding current and wire feed.
At this point the welding machine automatically carries out a succession of welded portions followed by a pause, according to
the times entered previously.
This procedure stops automatically only when the TORCH TRIGGER is released.
2) When the TORCH TRIGGER is pushed again the torch begins a new interval welding cycle.
CYCLE 4T LED ( ) switched on - CRATER LED ( ) flashing
■ STANDARD
1) When the TORCH TRIGGER is pushed the arc ignites and the parameters assume the values for the “initial crater”.
2) When the TORCH TRIGGER is released the parameters take on the “welding” values for a time set using the INITIAL SLOPE
(F11) function.
3) When the TORCH TRIGGER is pushed and released within 1 second, the parameters activated are those set for the “cycle”
functions. The operation can be repeated by switching between the “cycle” level and the “welding” level an infinite number of
times.
4) When the TORCH TRIGGER is pushed and held down for a period of time of more than 1 second, the parameters activated
are those with the values for the “final crater” for a period of time defined using the FINAL SLOPE (F12) function.
Releasing the TORCH TRIGGER will end the welding cycle.
■ ADVANCED
In ADVANCED operating mode, in addition to the settings described above, the welder is able to set the up “slope” (FIRST SLOPE
(F18)) and down “slope” (SECOND SLOPE (F21)) for the “cycle” level.
5
Switching on the welding machine
When the unit is switched on the welding machine's VISION SCREEN, shows the logo as shown below:
VISION Screen
During this operation, on the DH / VS panel:
• All the keys and all the encoders are disabled.
Language selection
LANGUAGE ENGLISH
ADVANCE CONFIGURATION DISABLED
ADVANCE WELDING MODE DISABLED
SX KEY COOLING MODE ON DEMAND DX KEY
WIRE LOAD BY GUN DISABLED
WIRE LOAD SPEED 0.8 m/min
VISION SCREEN
On the VISION SCREEN the DEFAULT language set by is ENGLISH.
To select another language, proceed as follows:
• Open the SETUP Menu by holding the SX KEY down for at least 5 consecutive seconds.
• Select the CONFIG Menu by rotating the ENCODER KNOB - SX until the correct icon is reached.
• Push the ENTER/MEM KEY to open the CONFIG Menu.
• Select the LANGUAGE Sub-menu by rotating the ENCODER KNOB - SX.
• Select the language required by rotating the ENCODER KNOB - DX.
• Push the MENU KEY to close the CONFIG Menu.
• Push the MENU KEY to close the SETUP Menu.
Once this has closed, the VISION SCREEN will show the various text / screens in the language selected.
Screen saver
After a pause or period of inactivity of the welding machine:
• The VISION SCREEN shows the SCREEN SAVER.
• On both the HT5 displays for the wire feeder, “CEA” appears and scrolls continuously.
VISION Screen Display HT5 (not used with DH 32 and VS 32)

The SCREEN SAVER mode can be exited in one of the following ways:
• By pushing any key or moving any knob on the welding machine's panel or that of the wire feeder.
• Starting the welding process, in which case the welding is activated in context.
• Moving a remote control.
When the SCREEN SAVER is exited, the welding machine goes back to the working condition prior to activation of the screen saver.
6
WELDING PROCESS SELECTION Menu (PROCESS)
To access the PROCESS SELECTION Menu (PROCESS) push the MENU KEY.
MIG PULSE
MIG DUAL PULSE
MIG/MAG SYNERGIC
MIG/MAG MANUAL
VISION.COLD
VISION.PIPE
VISION.POWER
1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
ENCODER KNOB - SX
VISION.POWER
VISION.ULTRASPEED
MMA
TIG LIFT
TIG LIFT PULSE
JOB
SEQUENCES
1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
ENCODER KNOB - SX
MENU KEY Provides access to the next menus.

ENCODER KNOB - SX Select the welding process.
ENTER/MEM KEY This key is used to access PRE-SETTING for the process selected.
The following processes are available:

• MIG PULSE (only DH)
• MIG DUAL PULSE (only DH)
• MIG-MAG SYNERGIC
• MIG-MAG MANUAL
• VISION.COLD (if activated)
• VISION.PIPE (if activated)
• VISION.POWER (if activated)
• VISION.ULTRASPEED (if activated)
• MMA
• TIG LIFT
• TIG LIFT PULSE
• JOB (if JOBS have been created)
• SEQUENCES (if SEQUENCES have been created)
“HT5” CONTROL PANEL (not used with DH 32 and VS 32)
It is not possible to access the PROCESS SELECTION Menu (PROCESS) via the HT5 control panel.
7
MIG-MAG, MIG pulse/dual pulse (Vision.PIPE, Vision.COLD, Vision.
POWER, Vision.ULTRASPEED only if activated)
1 - PROGRAM SELECTION Menu (PROGRAM)
To access the PROGRAM SELECTION Menu (PROGRAM) push the MENU KEY.
PRG MATERIAL Ø GAS

1011 Fe G3 SI-1 0.8 Ar 16-20% CO2
1012 Fe G3 SI-1 1.0 Ar 16-20% CO2
1013 Fe G3 SI-1 1.2 Ar 16-20% CO2
1014 Fe G3 SI-1 1.6 Ar 16-20% CO2
1021 Fe G3 SI-1 0.8 Ar 11-15% CO2
1/50
1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
ENCODER KNOB - SX
MENU KEY Used to access subsequent menus if there are any.

ENCODER KNOB - SX Select the welding program.
ENTER/MEM KEY Used to access PRE-SETTING of the program selected.
It is not possible to access the PROGRAM SELECTION Menu (PROGRAM) via the HT5 control panel.
2 - WELDING MODE SELECTION Menu (MODE)
To access the WELDING MODE SELECTION Menu (MODE) push the MENU KEY.
TWO STROKE (2T)

FOUR STROKE (4T)
CRATER 2T
CRATER 4T
SPOT WELDING
STITCH WELDING
1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
ENCODER KNOB - SX

ENCODER KNOB - SX Select the welding mode.
Used to access the PRE-SETTING for the program selected beforehand, in the MODE
ENTER/MEM KEY
chosen.
8
To access the WELDING MODE SELECTION Menu (MODE) push the WELDING MODE SELECTION KEY.
WELDING MODE SELECTION KEY
WELDING MODE SELECTION KEY Scrolls the various welding modes available in succession.
WELDING MODE SELECTION LED Displays the welding mode selected.
3 - SPECIAL FUNCTIONS Menu (SET UP Fx)
To access the SPECIAL FUNCTIONS Menu (SET UP Fx) push the MENU KEY.
DX KEY
POST GAS 1.0 s
DEFAULT
1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2

ENCODER KNOB - SX Used to select the various SPECIAL FUNCTIONS (Fx).
Used to access the PRE-SETTING for the program selected beforehand, in the MODE
ENTER/MEM KEY
chosen and with the changes made to the SPECIAL FUNCTIONS (Fx).
If held down for 2 seconds it makes it possible to return the value for the SPECIAL
DX KEY
FUNCTION (Fx) selected to the DEFAULT value.
ENCODER KNOB - DX Used to change the selected SPECIAL FUNCTION (Fx) value.
9
To access the SPECIAL FUNCTIONS Menu (SET UP Fx) push the SPECIAL FUNCTIONS (FX) KEY.
PARAMETER DISPLAY SCREEN - V
ENCODER KNOB - A
ENCODER KNOB - V
SPECIAL FUNCTIONS (FX) KEY

SPECIAL FUNCTIONS (FX) LED
PARAMETER DISPLAY SCREEN - A Displays the selected SPECIAL FUNCTION (Fx).

ENCODER KNOB - A Used to select the various SPECIAL FUNCTIONS (Fx).
PARAMETER DISPLAY SCREEN - V Displays the value for the selected SPECIAL FUNCTION (Fx).
ENCODER KNOB - V Used to change the selected SPECIAL FUNCTION (Fx) value.
Only enables entering and exit afterwards from the SPECIAL FUNCTIONS Menu (SET UP
Fx) on the HT5 panel and not on the DH/VS panel.
The operator must press the SPECIAL FUNCTIONS (SET UP FX) KEY for it to light up and be
included in the SPECIAL FUNCTIONS Menu (SET UP Fx).
The SPECIAL FUNCTIONS (Fx) related to the MIG-MAG synergic, MIG pulsed, MIG double pulsed, Vision.PIPE, Vision.COLD,
Vision.POWER, and Vision.ULTRASPEED processes, correspond to the feeder (when fitted) as follows:
Table A
PARAMETER DISPLAY Screen - V Welding mode
PARAMETER DISPLAY
FOUR STROKE (4T)
CYCLE ADVANCED
CYCLE STANDARD
Special function
TWO STROKE (2T)
Screen - A STITCH WELDING

SPOT WELDING
CRATER 2T
CRATER 4T
Default
Range
PRE GAS PrG 0.1s (0.0 - 2.0)s ● ● ● ● ● ● ● ●

STARTING SPEED StS 0 -30 - +30 ● ● ● ● ● ● ● ●
HOT START Hot 0 -30 - +30 ● ● ● ● ● ● ● ●
STITCH TIME F05 1.0s (0.1 - 20.0)s ●
STITCH PAUSE F06 1.0s (0.1 - 20.0)s ●
SPOT TIME F07 3.0s (0.1 - 20.0)s ●
INITIAL CURRENT F08 20% -50% - +100% ● ● ● ●
INITIAL ARC LENGTH F09 0 -30 - +30 ● (*) ● (*) ● (*) ● (*)
INITIAL CRATER TIME F10 1.0s (0.0 - 20.0)s ●
INITIAL SLOPE F11 1.0s (0.0 - 20.0)s ● ● ● ●
FINAL SLOPE F12 1.0s (0.0 - 20.0)s ● ● ● ●
(continued)
10
PARAMETER DISPLAY
FOUR STROKE (4T)
CYCLE ADVANCED
CYCLE STANDARD
Special function
TWO STROKE (2T)
STITCH WELDING
Screen - A
SPOT WELDING
CRATER 2T
CRATER 4T
Default
Range
FINAL CURRENT F13 -30% -100% - +50% ● ● ● ●
FINAL ARC LENGTH F14 0 -30 - +30 ● (*) ● (*) ● (*) ● (*)
FINAL CRATER TIME F15 0.0s (0.0 - 20.0)s ●
BURN BACK bub 0 -30 - +30 ● ● ● ● ● ● ● ●
POST GAS PoG 1.0s (0.0 - 10.0)s ● ● ● ● ● ● ● ●
FIRST SLOPE ( I1 TO I2 ) F18 0.05s (0.00 - 2.00)s ●
CYCLE CURRENT F19 20% -99% - +100% ● ●
CYCLE ARC LENGTH F20 0 -30 - +30 ● ●
SECOND SLOPE ( I2 TO I1 ) F21 0.05s (0.00 - 2.00)s ●
FIRST SLOPE ( I1 TO I2 ) F22 * 5 (0 - 100) ● (°) ● (°) ● (°) ● (°) ● (°) ● (°) ● (°) ● (°)
DUAL PULSE DELTA CURRENT F23 * 50% -100% - +200% ● ● ● ● ● ● ● ●
DUAL PULSE ARC LENGTH F24 * 0 -30 - +30 ● (°) ● (°) ● (°) ● (°) ● (°) ● (°) ● (°) ● (°)
DUAL PULSE BALANCE F25 * 0% -40% - +40% ● ● ● ● ● ● ● ●
DUAL PULSE FREQUENCY F26 * 2.7Hz (0.1 - 5.0)Hz ● ● ● ● ● ● ● ●
SECOND SLOPE ( I2 TO I1 ) F27 * 5 (0 - 100) ● (°) ● (°) ● (°) ● (°) ● (°) ● (°) ● (°) ● (°)
SLOPE JOB F28 0.5s (0.1 - 20.0) s ● ● ● ● ● ● ● ●
DYNAMICS din ** 0 -30 - +30 ● ● ● ● ● ● ● ●
* Only for the MIG double pulsed process.

** Only for the Vision.ULTRASPEED process.
WARNING:
• The STANDARD or ADVANCED welding CYCLE mode can only be activated by opening the ADVANCED SETUP Menu - AD-
VANCED MODE - CYCLE (for further explanations, see the relevant paragraph).
• (*) This SPECIAL FUNCTION is only to be found if the ADVANCED CRATER function has been activated by accessing the AD-
VANCED SETUP Menu - ADVANCED MODE - CRATER - ADVANCED (for further explanations, see the relevant paragraph).
• (°) These SPECIAL FUNCTIONS can only be activated for all the welding machine’s welding modes but going to the ADVANCED
SETTINGS Menu - ADVANCED MODE - DOUBLE PULSED - ADVANCED (for further explanations, see the relevant paragraph).
• It is possible to access editing of the SPECIAL FUNCTIONS (Fx) during welding.
• Some of the values edited will be used immediately by the operator, while others will be active from when the next welding
task begins.
• The HOLD function is not active within the SPECIAL FUNCTIONS Menu (SET UP Fx).
11
The SPECIAL FUNCTIONS (Fx) for the MIG-MAG manual process correspond to the feeder (when fitted) as follows:
Table B
PARAMETER DISPLAY
FOUR STROKE (4T)
CYCLE ADVANCED
CYCLE STANDARD
Special function
TWO STROKE (2T)
STITCH WELDING
Screen - A
SPOT WELDING
CRATER 2T
CRATER 4T
Default
Range
PRE GAS PrG 0.1s (0.0 - 2.0)s ● ● ● ● ● ● ● ●
STARTING SPEED StS 0 -30 - +30 ● ● ● ● ● ● ● ●
HOT START Hot 0 -30 - +30 ● ● ● ● ● ● ● ●
STITCH TIME F05 1.0s (0.1 - 20.0)s ●
STITCH PAUSE F06 1.0s (0.1 - 20.0)s ●
SPOT TIME F07 3.0s (0.1 - 20.0)s ●
INITIAL WIRE SPEED F08 5.0m/min (0.6-MAX)m/min ● ● ● ●
INITIAL VOLTAGE F09 25.0V (10 - MAX)V ● ● ● ●
INITIAL CRATER TIME F10 1.0s (0.0 - 20.0)s ●
INITIAL SLOPE F11 1.0s (0.0 - 20.0)s ● ● ● ●
FINAL SLOPE F12 1.0s (0.0 - 20.0)s ● ● ● ●
FINAL WIRE SPEED F13 5.0m/min (0.6-MAX)m/min ● ● ● ●
FINAL VOLTAGE F14 25.0V (10 - MAX)V ● ● ● ●
FINAL CRATER TIME F15 0.0s (0.0 - 5.0)s ●
BURN BACK bub 0 -30 - +30 ● ● ● ● ● ● ● ●
POST GAS PoG 1.0s (0.0 - 10.0)s ● ● ● ● ● ● ● ●
FIRST SLOPE ( I1 TO I2 ) F18 0.05s (0.00 - 2.00)s ●
CYCLE WIRE SPEED F19 5.0m/min (0.6-MAX)m/min ● ●
CYCLE VOLTAGE F20 25.0V (10 - MAX)V ● ●
SECOND SLOPE ( I2 TO I1 ) F21 0.05s (0.00 - 2.00)s ●
SLOPE JOB F28 0.5s (0.1 - 20.0) s ● ● ● ● ● ● ● ●
WARNING:
• The STANDARD or ADVANCED welding CYCLE mode can only be activated by opening the ADVANCED SETUP Menu - AD-
VANCED MODE - CYCLE (for further explanations, see the relevant paragraph).
task begins.
12
4 - PRE-SETTING
MENU KEY
A V
SX KEY
217 29.4 DX KEY
PROGRAM 1011
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
Used to access the PROCESS SELECTION Menu (PROCESS) and subsequent menus, as
MENU KEY
applicable.
Scrolls in succession THICKNESS OF WELDED ITEM ( ) - WELDING CURRENT ( )

SX KEY - WIRE SPEED ( ) only on the VISION SCREEN (this operation is activated when the key is
released).
ENCODER KNOB - SX Adjusts the parameter selected using the SX KEY.
Scrolls in succession ARC LENGTH ADJUSTMENT ( ) - WELDING VOLTAGE ( ) -

DX KEY ELECTRONIC INDUCTANCE ( ) only on the VISION SCREEN (this operation is activated when
the key is released).
ENCODER KNOB - DX Adjusts the parameter selected using the DX KEY.
PARAMETER DISPLAY SCREEN - A

ENCODER KNOB - A
ENCODER KNOB - V
WIRE KEY
GAS KEY
PARAMETER DISPLAY SCREEN - A Shows the value for the parameter indicated by the PARAMETER SELECTION LED - A.
PARAMETER SELECTION LED - A The LED unit shows the welding parameter selected using the PARAMETER SELECTION KEY - A.
PARAMETER SELECTION KEY - A Scrolls in succession THICKNESS OF WELDED ITEM ( ) - WELDING CURRENT ( )-
WIRE SPEED ( ).
ENCODER KNOB - A Adjusts the parameter displayed by the PARAMETER DISPLAY SCREEN - A.
WIRE KEY Activates loading of the wire.
WELDING MODE SELECTION KEY Scrolls the various welding modes in succession.
WELDING MODE SELECTION LED The LED unit indicates the welding mode selected according to the VISION SCREEN.
PARAMETER DISPLAY SCREEN - V Shows the parameter indicated by the PARAMETER SELECTION LED - V.
The LED unit indicates the welding parameter selected using the PARAMETER SELECTION KEY
- V.
PARAMETER SELECTION KEY - V Scrolls in succession ARC LENGTH ADJUSTMENT ( ) - WELDING VOLTAGE ( )-
ELECTRONIC INDUCTANCE ( ).
(continued)
13
ENCODER KNOB - V Adjusts the parameter displayed by the PARAMETER DISPLAY SCREEN - V.
GAS KEY Activates the flow of gas.
Fx) on the HT5 panel and not on the DH panel.
5 - WELDING
When welding takes place the fields in the displays show the same values as those included for pre-setting with the difference
that now they are those measured.
A V
217 29.4
PROGRAM 1011
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
14
6 - HOLD
When welding ends the fields in the display must show the same values that were displayed during welding, with the difference
that they are now values defined as HOLD. In this phase the VISION SCREEN shows the HOLD box highlighted, while on the HT5
panel the HOLD FUNCTION LED flashes until the end of the HOLD Function. If the HOLD Function is Interrupted via a panel (e.g. DH),
it will also be interrupted automatically on the other (HT5) and vice-versa.
HOLD
A V
217 29.4
PROGRAM 1011
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
HOLD Function LED
15
7 - WIRE LOADING
The purpose of this menu it to allow the operator to load the welding wire and set the loading speed, only when welding is not
is progress. If the wire loading function is activated (also see the CONFIG menu), to enable it hold the torch button or the load-
ing button on the feeder down for 4 seconds.
m/min
8.0
ENCODER KNOB - SX
Rotate the ENCODER KNOB - SX the wire loading speed can be changed from 1,0 to 22,0 (default 8,0). The other keys and knobs
are not active.
When the torch button or the wire loading key on the HT5 feeder are released, the machine goes back to its previous status. For
models not fitted with an HT5 feeder, that is DH 32 and VS 32, loading is done by pushing the relevant (wire test / gas
test) button, located in the space in which the wire coil is housed.
NOTE: Wire loading cannot be accessed when their are errors on the machine or in the set-up procedure.
WIRE KEY
Rotate the ENCODER KNOB - SX the wire loading speed can be changed from 1,0 to 22,0 (default 8,0). The other keys and knobs
are not active.
8 - DOUBLE FEEDER
Two feeders can be connected to the same generator simultaneously. Once everything has been configured correctly, as indi-
cated in the HT5 operator’s manual and set as indicated in the equipment layout section, the machine’s display shows one of
the following two images.
The number ➊ or ➋ on the display indicates that the feeder in use at that time is number 1 or 2. If no number is displayed, this
means that only one feeder has been configured.
MENU KEY
A V A V
105 19.5 111 19.4
PROGRAM 1402 PROGRAM 1402
Al 99.5 Al 1050 Ø 1.0 Ar 99.9% Fe G3 Sl-1 Ø 0.8 Ar 16-20% CO2
MENU KEY To switch from one feeder to the other, hold down the MENU KEY. (*)
(*) Switching from one feeder to the other can also be done by pushing the relevant torch button.
16
MMA
Select the MMA welding process by using the MENU KEY as explained on page 7.
1 - PROGRAM SELECTION Menu (PROGRAM) MMA
To access the PROGRAM SELECTION Menu (PROGRAM) push the MENU KEY.
PRG TYPE
ϯϬϬϬ DDZƵƟů
3100 MMA Basic
3200 MMA Cr Ni
3/3
3200 MMA Cr Ni
ENCODER KNOB - SX

ENCODER KNOB - SX Select the welding program.
ENTER/MEM KEY Used to access PRE-SETTING of the program selected.
It is not possible to access the PROGRAM SELECTION Menu (PROGRAM) via the HT5 control panel.
2 - SPECIAL FUNCTIONS Menu (SET UP Fx) MMA
DX KEY
HOT START 50
DEFAULT
3200 MMA Cr Ni

Used to access the PRE-SETTING with the changes made to the SPECIAL FUNCTIONS
ENTER/MEM KEY
(Fx).
DX KEY
17
ENCODER KNOB - A
ENCODER KNOB - V


The SPECIAL FUNCTIONS (Fx) related to the MMA process correspond as follows to those on the wire feeder:
PARAMETER DISPLAY Screen - V

Special function PARAMETER DISPLAY Screen - A
Default Range
HOT START Hot 50 (0 - 100)
ARC FORCE ArC 50 (0 - 100)
WARNING:
task begins.
18
3 - PRE-SETTING MMA

A V
SX KEY
60 70.0 DX KEY
PROGRAM 3200
MMA Cr Ni
MENU KEY
applicable.
ENCODER KNOB - SX Adjust the value of the parameter WELDING CURRENT ( ).
DX KEY Scrolls in succession WELDING VOLTAGE ( ) - HOT START ( ) - ARC FORCE ( ) only
on the VISION SCREEN (the operation is activated when the key is released).
ENCODER KNOB - DX Adjusts the parameter selected using the DX KEY (only HOT START ( ) - ARC FORCE ( )).

ENCODER KNOB - A
ENCODER KNOB - V

PARAMETER DISPLAY SCREEN - A Displays the value of the parameter WELDING CURRENT ( ).
PARAMETER SELECTION LED - A The LED unit shows the WELDING CURRENT ( ) switched on.
ENCODER KNOB - A Adjust the value of the parameter WELDING CURRENT ( ).

Shows the parameter indicated by the PARAMETER SELECTION LED - V.
The WELDING VOLTAGE shown is the measured voltage.
- V.
PARAMETER SELECTION KEY - V Scrolls in succession the parameters HOT START ( ) - WELDING VOLTAGE ( ) - ARC
FORCE ( ).
ENCODER KNOB - V Adjusts the parameter displayed by the PARAMETER DISPLAY SCREEN - V.
19
4 - WELDING MMA
A V
60 70.0
PROGRAM 3200
MMA Cr Ni
20
5 - HOLD MMA
HOLD
A V
68 7.2
PROGRAM 3200
MMA Cr Ni
HOLD Function LED
21
6 - ACTIVATING THE VRD DEVICE MMA
The Voltage Reduction Device (VRD) is a safety device that reduces voltage. It prevents voltages forming on the output termi-
nals that may pose a danger to people. The standard settings and those defined beforehand by do not provide for the VRD to be
active on the welding machine and so the VISION SCREEN does not normally provide any indication.
If the operator wishes to weld in MMA using the VRD device (which must be done with the welding machine switched off), they must:
1) Use a suitable screwdriver to unscrew the 4 screws that fix the DH/VS control panel to the welding machine.
2) Remove the “VRD” JUMPER on the DIGITAL INTERFACE PCB (see figure).
3) Use a suitable screwdriver to tighten the 4 screws that fix the DH/VS control panel to the welding machine.
4) Start the welding machine by turning the switch on the rear panel to position I.
When it switches on, but with the machine in stand-by, the DH/VS control panel shows that the VRD device is active (indication
on the VISION SCREEN green colour - see enclosed image: MMA - PRE-SETTING).
DISPOSITIVO VRD
A V
60 70.0
PROGRAM 3200
MMA Cr Ni
During the welding phase the VRD device is activated (indication on the VISION SCREEN red colour (does not indicate malfunction-
ing of the welding machine) - see enclosed image: MMA - WELDING) and when welding is ended the voltage will be reduced
within a maximum time of 0,3 seconds.
22
TIG LIFT
Select the TIG LIFT welding process by using the MENU KEY as explained on page 7.
1 - SPECIAL FUNCTIONS Menu (SET UP Fx) TIG LIFT
SX KEY DX KEY
SLOPE UP 2.0 s
DEFAULT

Used to access the PRE-SETTING with the changes made to the SPECIAL FUNCTIONS
ENTER/MEM KEY
(Fx).
DX KEY
ENCODER KNOB - A
ENCODER KNOB - V


23
The SPECIAL FUNCTIONS (Fx) related to the TIG LIFT process correspond as follows to those on the wire feeder:
PARAMETER DISPLAY Screen - V

Special function PARAMETER DISPLAY Screen - A
Default Range
UP SLOPE F29 0.0s (0.0 - 5.0)s
DOWN SLOPE F30 2.0s (0.0 - 8.0)s
TIG PULSE DELTA CURRENT F23 -50% (-100 ÷ 1000)%
TIG PULSE BALANCE F25 0 (-40 ÷ 40)%
TIG PULSE FREQUENCY F26 100.0Hz (0.1 ÷ 500.0)Hz
SWS VOLTAGE THRESHOLD F31 0 -30 - +30
WARNING:
task begins.
2 - PRE-SETTING TIG LIFT
MENU KEY
A V
111 50.0
ENCODER KNOB - SX
MENU KEY
applicable.
ENCODER KNOB - SX Adjust the value of the parameter WELDING CURRENT ( ).

ENCODER KNOB - A
PARAMETER DISPLAY SCREEN - A Displays the value of the parameter WELDING CURRENT ( ).
PARAMETER SELECTION LED - A The LED unit shows the WELDING CURRENT ( ) switched on.
(continued)
24
ENCODER KNOB - A Adjust the value of the parameter WELDING CURRENT ( ).
PARAMETER DISPLAY SCREEN - V Displays the value of the parameter WELDING VOLTAGE ( ).
The WELDING VOLTAGE shown is the measured voltage.
PARAMETER SELECTION LED - V The LED unit shows the WELDING VOLTAGE ( ) switched on.
3 - WELDING TIG LIFT

A V
111 50.0
25
4 - HOLD TIG LIFT
HOLD
A V
39 1.2
HOLD Function LED
26
JOB/SEQUENCES
1 - Creating and saving / editing and overwriting a JOB/SEQUENCES (*) JOB/SEQUENCES

A V
SX KEY
211 24.8 DX KEY
PROGRAM 0011
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
VISION SCREEN
(*) For the sequences, see the relevant paragraph in the settings menu.
CREATING AND SAVING A JOB
To create and save a JOB (automatic welding point) proceed as follows:
• During any welding process and at any time, once you have acquired the necessary parameters, hold
PRG JOB
001 MMA
PROCESS I
97 the ENTER/MEM KEY down for 3 consecutive seconds.
002
003
--- ---
--- ---
---
---
• The VISION SCREEN automatically goes to the first free position in the JOB table.
004
005
--- ---
--- ---
---
---
• Choose the position in which the JOB is to be saved by rotating the ENCODER KNOB - SX.
• Push the ENTER/MEM KEY to confirm and finalise saving of the JOB created.
011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
PRG JOB PROCESS I

001 MMA 97
002 0011 MIG/MAG SYNERGIC 211
003 --- --- ---
004 --- --- ---
005 --- --- ---
011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
EDITING AND OVERWRITING A JOB
A V To edit and/or overwrite a JOB proceed as follows:

• During any welding process and at any time push the MENU KEY to exit the welding phase.
211 24.8 • Select the welding process JOB by rotating the ENCODER KNOB - SX.
• Push the MENU KEY to open the JOB table.
• Select the JOB to be edited by rotating the ENCODER KNOB - SX.
• Push the ENTER/MEM KEY to view the settings on the VISION SCREEN for the JOB to be edited.
002
PROGRAM 0011
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2 • Hold down the ENTER/MEM KEY for about 3 consecutive seconds, until the VISION SCREEN loads all the
parameters / data for the JOB onto the screen (making them available to the operator).
• Acquire the parameters necessary for editing the JOB.
• Hold down the ENTER/MEM KEY for 3 consecutive seconds.
PRG JOB PROCESS I • The VISION SCREEN automatically goes to the first free position in the JOB table.
• Choose the free position in which the edited JOB is to be saved, or a position already occupied in
001 MMA 97
which the edited JOB will be overwritten, by rotating the ENCODER KNOB - SX.
003 --- --- ---
004 --- --- ---
005 --- --- ---
• Push the ENTER/MEM KEY to confirm the operation.
OVERWRITE JOB 002? • Push the SX KEY to confirm the overwriting operation or the DX KEY to cancel it.
It is not possible to create, save, edit or overwrite a JOB/SEQUENCE using the “HT5” control panel.
27
2 - JOB/SEQUENCES SELECTION Menu JOB/SEQUENCES
WARNING: All the parameters saved within a JOB/SEQUENCE (including SPECIAL FUNCTIONS (Fx)) can be viewed but not
edited!
To access the JOB/SEQUENCES SELECTION Menu push the MENU KEY.

JOB PRG PROCESS SYN

001 1011 MIG PULSE 100A
002 7011 VISION.ULTRASPEED 124A
003 2011 MIG DUAL PULSE 100A
004 1011 MIG PULSE 240A
005 1011 MIG PULSE 53A
1/5 001
1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
ENCODER KNOB - SX
SEQ NAME # JOB

001 Welding sequence 2
002 Welding sequence 1 4
1/4 001
1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
ENCODER KNOB - SX
MENU KEY Used to access subsequent menus.

ENCODER KNOB - SX Used to scroll and select a JOB/SEQUENCES.
ENTER/MEM KEY Used to select the JOB/SEQUENCE displayed.

ENCODER KNOB - A
ENCODER KNOB - V
WIRE KEY
GAS KEY
Shows the JOB term or value of the parameter indicated by the PARAMETER SELECTION LED -
A.
Scrolls the active parameters in succession, based on the type of welding process saved in
the JOB selected.
(continued)
28
The LED unit indicates the welding mode saved in the JOB selected, which is coherent with
the VISION SCREEN.
Displays the JOB number also selected in the SEQUENCES or the value for the parameter
indicated by the PARAMETER SELECTION LED - V.
the JOB selected.
ENCODER KNOB - V Used to scroll through the JOBS in the SEQUENCES as well.
SPECIAL FUNCTIONS (FX) KEY Used to access displaying of the SPECIAL FUNCTIONS (Fx) saved in the JOB selected.
3 - PRE-SETTING JOB/SEQUENCES
WARNING: All the parameters saved within a JOB (including SPECIAL FUNCTIONS (Fx)) can be viewed but not edited!

m/min V
SX KEY
11.1 33.3 DX KEY
013
VISION SCREEN

mm
SX KEY
2.8 0 DX KEY
001
001
1011 - Welding sequence
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
VISION SCREEN
MENU KEY
applicable.
SX KEY
the JOB selected.
If held down for a period of about 3 consecutive seconds, this key allows the VISION SCREEN to
ENTER/MEM KEY
load all the parameters for the JOB onto the screen (making them available to the operator).
DX KEY
the JOB selected.
29

ENCODER KNOB - A
ENCODER KNOB - V
WIRE KEY
GAS KEY
A.
the JOB selected.
the VISION SCREEN.
- V.
the JOB selected.
ENCODER KNOB - V Used to scroll through the JOBS in the SEQUENCES as well.
SPECIAL FUNCTIONS (FX) KEY Used to access the SPECIAL FUNCTIONS (Fx) saved in the JOB selected.
30
4 - WELDING JOB/SEQUENCES
MENU KEY
m/min V
SX KEY
11.1 33.3 DX KEY
013
MENU KEY
mm
SX KEY
2.8 0 DX KEY
001
001
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
MENU KEY
applicable.
Scrolls the active parameters in succession, only on the VISION SCREEN, based on the type of
SX KEY welding process saved in the JOB selected.
In this case, where possible, the values displayed will be those measured.
Scrolls the active parameters in succession, only on the VISION SCREEN, based on the type of
DX KEY welding process saved in the JOB selected.

ENCODER KNOB - A
ENCODER KNOB - V
WIRE KEY
GAS KEY
A.
PARAMETER SELECTION KEY - A the JOB selected.
(continued)
31
the VISION SCREEN.
- V.
PARAMETER SELECTION KEY - V Used to access displaying of the SPECIAL FUNCTIONS (Fx) saved in the JOB selected.
ENCODER KNOB - V Used to scroll through the JOBS in the SEQUENCES as well, only if these are coherent. (*)
SPECIAL FUNCTIONS (FX) KEY Used to access the SPECIAL FUNCTIONS (Fx) saved in the JOB selected.
(*) The JOBS included in the SEQUENCES as well as considered to be coherent when the last three figures (wire type,
gas, wire diameter) are equal. WHEN THIS IS THE CASE JOBS CAN BE CHANGED DURING WELDING WITHOUT INTER-
RUPTION.
5 - HOLD JOB/SEQUENCES
HOLD
m/min V
11.1 33.3
013
32
HOLD
mm
2.8 0
001
001
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
HOLD Function LED
33
Error condition
WARNING: Under normal conditions of use it is not possible to open the “ERROR LOG Menu” display since the alarm message
appears instantaneously on the VISION SCREEN as soon as the problem arises on the welding plant. At this stage it is not possi-
ble to weld!
As soon as the error message appears:
ERRORS 1
E0.6 WATER COOLER MISSING
SX KEY
ENCODER KNOB - SX
VISION SCREEN
If held down for a period of about 5 consecutive seconds it takes the VISION SCREEN to the
SX KEY
SETUP Menu.
ENCODER KNOB - SX Used to scroll the alarms activated.
Shows the alarm signal ( ), number of the errors that have occurred (e.g. ERRORS 1) and
VISION SCREEN an indication of what happened (e.g. E.06 WATER COOLER MISSING) of the welding ma-
chine.
In the case of an Automatically reset error once the alarm condition has ended (reinstatement completed correctly), the weld-
ing plant is once again ready and the operator can recommence welding! The alarm state disappears and the VISION SCREEN re-
turns to precisely the same point at which it was operating previously.
PLEASE NOTE: After resetting has been completed, during normal operation of the machine, the VISION SCREEN will still show the
error signal to inform the operator of the event ( ), but this can be removed visually from the display by simply pushing the MENU
KEY. WARNING: This only removes the visual error indication but not the history of what happened!
In the case of NON automatically reset errors, to remove the alarm status and reinstate correct operation of the machine, the
welding plant must be switched off.
When it is switched on again, the machine will be working again and the operator can weld again!
PLEASE NOTE: If, when switching on, the error status presents itself again, immediately contact’s Technical Assis-
tance Department.

ENCODER KNOB - A
ENCODER KNOB - V
WIRE KEY
GAS KEY
PARAMETER DISPLAY SCREEN - A Displays the error message (e.g. Err.).

Shows the alarm code (e.g. E0.6) of in succession, the codes for the alarms in succession if
there are a number of errors.
In the case of an Automatically reset error once the alarm condition has ended (reinstatement completed correctly), the weld-
ing plant is once again ready and the operator can recommence welding! The alarm state disappears and the VISION SCREEN re-
turns to precisely the same point at which it was operating previously.
34
PLEASE NOTE: After resetting has been completed, during normal operation of the machine, the VISION SCREEN will still show the
error signal to inform the operator of the event ( ), but this can be removed visually from the display by simply pushing the MENU
KEY. WARNING: This only removes the visual error indication but not the history of what happened!
If an Error NOT automatically resettable arises, to eliminate the alarm state and reinstate correct functioning of the machine,
switch the plant off and then on again, or hold down the DX KEY.
When it is switched on again, the machine will be working again and the operator can weld again!
PLEASE NOTE: If, when switching on, the error status presents itself again, immediately contact Technical Assistance
Department.
SETUP Menu
To access the SETUP Menu hold down for at least 5 consecutive seconds the SX KEY.
SETUP
ENCODER KNOB - SX
MENU KEY Used to exit the SETUP Menu and take the VISION SCREEN back to the entry phase.
ENCODER KNOB - SX Used to scroll the various icons (sub-menus) in the menu and then select them.
ENTER/MEM KEY Used to access the menu related to the icon selected.
WARNING:
• It is impossible to weld!
• If the VISION SCREEN is protected by a password, access to this menu will only be allowed by entering the correct password.
The icons (sub-menus) available and that can be viewed within the SETUP Menu are:
• JOB EDIT
• PASSWORD
• BLOCKS
• CONFIG
• FACTORY RESET
• INFO
• NETWORK
• ERROR LOG
ACCESSING THE SUB-MENUS
SETUP To access the sub-menus included in the SETUP Menu, you must:
• Turn the ENCODER KNOB - SX to select the desired icon.
• Push the ENTER/MEM KEY.
It is not possible to access the SETUP Menu and all the related sub-menus using the “HT5” control panel.
35
JOB EDIT SETUP Menu
The purpose of this menu is to allow the operator to copy or delete a JOB (automatic welding point) entered previously.
To access the JOB EDIT Menu from the SETUP Menu:

PRG JOB PROCESS I

001 MMA 97
SX KEY 003 MMA 97 DX KEY
004 --- --- ---
005 --- --- ---
006 --- --- ---
VISION SCREEN
COPYING THE JOB SELECTED

To copy the JOB selected, proceed as follows:
• Select the JOB to be copied by rotating the ENCODER KNOB - SX.
PRG JOB
001 MMA
PROCESS I
97
• Push the SX KEY.
002 0011 MIG/MAG SYNERGIC
003 MMA
211
97
• Choose the position to which the JOB selected is to be copied (or overwritten *) by rotating the
004
005
--- ---
--- ---
---
---
ENCODER KNOB - SX.
006 --- --- ---
• Push the ENTER/MEM KEY to confirm and finalise copying of the JOB selected.
COPY JOB 002
* In the case of overwriting, confirmation will be requested.
DELETING THE JOB SELECTED

To delete the JOB selected, proceed as follows:
• Select the JOB to be deleted by rotating the ENCODER KNOB - SX.
PRG JOB
001 MMA
PROCESS I
97
• Push the DX KEY.
003 MMA
211
97
• Push the SX KEY to confirm and finalise deletion of the JOB selected.
005 --- ---
211
---
• To cancel the operation of deleting the JOB selected, push the DX KEY.
006 --- --- ---
DELETE JOB 004?
To exit the JOB EDIT Menu and go back to the SETUP Menu:
• Push the MENU KEY.
36
SEQ EDIT SETUP Menu
The purpose of this menu is to allow the operator to create, copy, overwrite, or delete a welding sequence.
To access the SEQ EDIT Menu from the SETUP Menu:

SETUP
SX KEY DX KEY
ENCODER KNOB - SX

JOB/SEQUENCES
SX KEY DX KEY
The following image appears:
SEQ NAME # JOB

001 --- ---
002 --- ---
003 --- ---
004 --- ---
005 --- ---
006 --- ---
CREATING A SEQUENCE
SEQ 001
JOB PRG
NAME
PROCESS SYN
Use the ENTER/MEM KEY to create a new sequence.
--- --- --- ---
AVAILABLE JOBS: 5
001 1011 MIG PULSE 100A
003 2011 MIG DUAL PULSE 100A
SEQ
JOB
001
PRG
NAME
PROCESS SYN
Use the SX KEY to add the JOB selected using the ENCODER KNOB - DX to the section of the sequence
001
003
1011 MIG PULSE
2011 MIG DUAL PULSE
100A
100A
selected using the ENCODER KNOB - SX.
--- --- --- --- The image shows the two jobs (001 and 003) added to the sequence. The yellow colour indicates that
AVAILABLE JOBS: 5
the JOBS have already been used. The JOBS already used can be used again in other sections of the
001 1011 MIG PULSE
002 7011 VISION.ULTRASPEED
100A
124A
sequence.
003 1011 MIG PULSE 100A
(continua)
37
SEQ
JOB
001
PRG
NAME Sequenza Saldatura
PROCESS SYN
Use the DX KEY to remove the JOB from the section of the sequence selected using the
001
003
1011 MIG PULSE
2011 MIG DUAL PULSE
100A
100A
ENCODER KNOB - SX.
--- --- --- --- Push the ENTER/MEM KEY to be able to edit the sequence name.
AVAILABLE JOBS: 5
001 1011 MIG PULSE 100A
003 1011 MIG PULSE 100A
Use the ENCODER KNOB - DX and the ENCODER KNOB - SX SX respectively to select the which of the
characters available is required, and to move to the position of the next or the previous character.
SEQ
001
NAME
Welding sequence
# JOB
2
Once creation of the sequence has been completed, push the MENU KEY to save it.
002 --- ---
003 --- ---
004
005
---
---
---
---
As you can see, the sequence number is shown on the left, the name of the sequence in the centre,
006 --- ---
and the total number of jobs used for the sequence on the right.
Once the welding sequence has been created, the SX KEY can be used to copy it, the DX KEY to delete it,
or the ENTER/MEM KEY to edit it.
COPYING A SEQUENCE
Select the sequence to be copied using the ENCODER KNOB - SX and push the SX KEY.
SEQ NAME # JOB
003 --- ---
005 --- ---
006 --- ---
The copy sequence 004 message displayed indicates that sequence 4 has been selected.
SEQ NAME # JOB
003 --- ---
005 --- ---
006 --- ---
COPY SEQ. 004
Select the position of the sequence to be added, using the ENCODER KNOB - SX (e.g. in this case, position
6).
SEQ
002
NAME
Welding sequence 1
# JOB
2
Until the DX KEY is pushed of a new sequence is selected using the SX KEY, sequence 004 can be added
003
004
---
Welding sequence 2
---
4
in all the positions it is required.
005 --- ---
006 --- ---
007 --- ---
COPY SEQ. 004
Push the ENTER/MEM KEY to copy the sequence.

SEQ NAME # JOB
003 --- ---
005 --- ---
007 --- ---
COPY SEQ. 004
If the sequence position chosen is already in use, when the ENTER/MEM KEY is pushed the image to the
left is displayed.
SEQ
002
NAME
Welding sequence 1
# JOB
2
Push the SX KEY and sequence4 6 will be replaced by sequence 4, whereas the DX KEY cancels
003
004
---
Welding sequence 2
---
4
everything.
005 --- ---
007 --- ---
OVERWRITE SEQ. 006 WITH SEQ. 004?
DELETING A SEQUENCE
Select the sequence to be deleted using the ENCODER KNOB - SX and push the SX KEY.
SEQ NAME # JOB
003 --- ---
005 --- ---
(continua)
38
Confirm using the SX KEY or cancel using the DX KEY.
SEQ NAME # JOB
003 --- ---
005 --- ---
DELETE SEQ. 006?
EDITING A SEQUENCE
Select the position of the sequence to be edited using the ENCODER KNOB - SX and push the ENTER/MEM
KEY.
SEQ
001
NAME
Welding sequence
# JOB
2
The sequence to be edited will be displayed, with all already described for creating the sequence.
003 --- ---
005 --- ---
To exit the JOB EDIT Menu and go back to the SETUP Menu:
PASSWORD SETUP Menu

The purpose of this menu is to allow the operator to enter a PASSWORD for accessing the SETUP Menu.
To access the PASSWORD Menu from the SETUP Menu:

SET PASSWORD
SX KEY
000 DX KEY
VISION SCREEN
The VISION SCREEN can have various configurations, the meaning of which is indicated in the table below.
Diaplay VISION DESCRIPTION Meaning

000 The SETUP Menu ARE NOT protected by any PASSWORD.
*** The SETUP Menu ARE protected by any PASSWORD.
Number between 001 and 999 The SETUP Menu ARE protected by a PASSWORD and this can be seen by the
operator only because they are working inside the SETUP Menu.
ENTERING A NEW PASSWORD

To enter a new PASSWORD proceed as follows:
• Make sure that the VISION SCREEN displays the text 000.
SET PASSWORD
• Choose the new PASSWORD to be entered by rotating the ENCODER KNOB - DX.
011 • Push the ENTER/MEM KEY to confirm the operation of entering the PASSWORD.
• Push the SX KEY to confirm and finalise entering of the new PASSWORD.
• To cancel the operation of entering a PASSWORD push the DX KEY.
STORE PASSWORD?
(continued)
39
EDITING THE EXISTING PASSWORD
WARNING: This operation is only possible after having accessed the SETUP Menu using the password
you wish to edit!
SET PASSWORD To edit the existing PASSWORD proceed as follows:

077 • Make sure the VISION SCREEN shows the PASSWORD entered previously (a number that must be
between 001 and 999).
• Choose the new PASSWORD to be entered by rotating the ENCODER KNOB - DX.
STORE PASSWORD? • Push the ENTER/MEM KEY to confirm the operation of editing the PASSWORD.
• Push the SX KEY to confirm and finalise editing of the PASSWORD.
• To cancel the operation of editing a PASSWORD push the DX KEY.
DELETING THE EXISTING PASSWORD
WARNING: This operation is only possible after having accessed the SETUP Menu using the password
you wish to delete!
SET PASSWORD To delete the existing PASSWORD proceed as follows:

000 • Make sure the VISION SCREEN shows the PASSWORD entered previously (a number that must be
between 001 and 999).
• Take the VISION SCREEN to number 000 by rotating the ENCODER KNOB - DX.
STORE PASSWORD? • Push the ENTER/MEM KEY to confirm the deletion of the PASSWORD.
• Push the SX KEY to confirm and finalise deleting of the PASSWORD.
• To cancel the operation of deleting a PASSWORD push the DX KEY.
To exit the PASSWORD Menu and go back to the SETUP Menu:

BLOCKS SETUP Menu

The purpose of this menu is to allow the operator to block or limit use of the welding machine and/or certain welding parame-
ters / functions.
To access the BLOCKS Menu from the SETUP Menu:

The image graphically shows how the type of block is shown on the VISION SCREEN when the welding machine is operating normally.
A L2
V
212 24
PROGRAM 0011
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
Within the BLOCKS Menu it is possible to select, by rotating the ENCODER KNOB - DX, the block required (this operation does not
require confirmation) from the 4 options available:
Block type Description

NONE BLOCK ABSENT or RELEASE MACHINE
Does not allow any block to be activated on the welding machine, but allows the operator
to release the machine if its was blocked previously.
BLOCK TYPE NONE
(continued)
40
Block type Description
LEVEL 1 PARTIAL BLOCK
The operator can weld using the parameters set prior to the block and may make
adjustments and/or changes to the welding parameters using the knobs on the control
BLOCK TYPE LEVEL 1 panels on the welding machine and the wire feeder (if fitted).
LEVEL 2 TOTAL BLOCK

The operator can weld only using the parameters set prior to the block and cannot adjust
and/or edit the welding parameters.
BLOCK TYPE LEVEL 2
USER BLOCK PERSONALISED BLOCK

Used to block or limit some adjustments and/or functions of the welding machine.
BLOCK TYPE USER BLOCK

CURR./WIRE SPEED CHANGE BLOCKED
ARC LENGTH/VOLTAGE CHANGE BLOCKED
INDUCTANCE CHANGE BLOCKED
PROCESS CHANGE DISABLED
PROGRAM CHANGE DISABLED
JOB CHANGE DISABLED
MODE CHANGE DISABLED
SPECIAL FUNCTION CHANGE DISABLED
To exit the BLOCKS Menu and go back to the SETUP Menu:

CONFIG SETUP Menu

The purpose of this menu is to allow the operator to select the language used for the VISION SCREEN, change the SETTINGS menu
to ADVANCED SETTINGS menu, enter advanced welding mode, set how cooling is managed, and set wire loading via the torch
button.
To access the CONFIG Menu from the SETUP Menu:

LANGUAGE ENGLISH
ADVANCED CONFIGURATION DISABLED
ADVANCED WELDING MODE DISABLED
COOLING MODE ON DEMAND
When the CONFIG Menu is open, the ENCODER KNOB - SX can be rotated to select the which of the 6 functions available is required.
This can be enabled (the operation does not require confirmation) by rotating the ENCODER KNOB - DX.
Advanced function Description

LANGUAGE Indicates the languages that can be set for the VISION SCREEN.
As regards the procedure for selecting a language on the VISION SCREEN see the relevant
paragraph in the manual (“Language Selection”).
LANGUAGE ENGLISH
(continued)
41
ADVANCED CONFIGURATION If enabled, this configuration offers the welder the following additional menus (the
following icons will be created in the ADVANCED SETUP Menu):
• ADVANCED CONFIG
LANGUAGE ENGLISH
• WELD LOG
ADVANCED CONFIGURATION ENABLED
ADVANCED WELDING MODE If enabled, this configuration allows the welder to have further welding modes available to
them (the following icons will be created in the ADVANCED SETUP Menu):
• ADVANCED MODE
LANGUAGE ENGLISH
ADVANCED WELDING MODE ENABLED
COOLING MODE This configuration allows the welder to set cooling as follows:
• WHEN REQUESTED. IIn this case, cooling is managed in relation to the welding done.
• ALWAYS ON. In this case, cooling comes on when the machine is switched on,
LANGUAGE ENGLISH
and stays on until the machine is switched off. Cooling only stops when an alarm is
ADVANCED CONFIGURATION
ADVANCED WELDING MODE
DISABLED
DISABLED
activated.
WIRE LOAD BY GUN This configuration allows the welder to enable or disable the type of wire loading from the
torch:
• ACTIVE. In this case wire loading is activated from the torch (also see relevant section).
LANGUAGE ENGLISH
• NOT ACTIVE. In this case, wire loading can only be done using the relevant button on
ADVANCED CONFIGURATION
ADVANCED WELDING MODE
DISABLED
DISABLED
the feeder.
WIRE LOAD SPEED The parameter is used to set the loading speed, both for the torch (if active) and for the
feeder.
The range for this parameter is 1,0 m/min to 22,0 m/min.
LANGUAGE ENGLISH
WARNING: The additional menus are explained in the manual, in the “ADVANCED SETUP Menu” paragraph.
To exit the CONFIG Menu and go back to the SETUP Menu:

42
FACTORY RESET SETUP Menu
The purpose of this menu is to allow the operator to return the welding machine partially or totally to the factory settings.
To access the FACTORY RESET Menu from the SETUP Menu:

RESET PROGRAM
RESET PROCESS DATA
DELETE ALL JOBS
COUNTER ALARMS RESET
TOTAL RESET
ENCODER KNOB - SX
Within the FACTORY RESET Menu it is possible, by rotating the ENCODER KNOB - SX, to select the individual RESET required,
from the 5 functions available:
Function Description
RESET PROGRAM Used to return the Special functions (Fx) of the PROGRAM that the operator is using to
their DEFAULT settings (only for welding processes for which welding programs are set
beforehand).
RESET PROGRAM (0011)
RESET PROCESS DATA MIG/MAG SYNERGIC
DELETE ALL JOBS
NOTE: The welding PROGRAM NUMBER for which the Special Functions (Fx) are to be
TOTAL RESET
returned to the factory settings is indicated on the VISION SCREEN.
EXECUTE PROGRAM RESET?
RESET PROCESS DATA Used to return the Special functions (Fx) of the welding PROCESS the operator is using
to their DEFAULT settings.

NOTE: The welding PROCESS for which the Special Functions (Fx) are to be returned to
DELETE ALL JOBS
the factory settings, is indicated on the VISION SCREEN.
TOTAL RESET
EXECUTE DATA PROCESS RESET?
DELETE ALL JOBS Used to delete all the JOBS saved previously by the operator.
WARNING: Remember that, when it leaves the factory the welding machine DOES NOT
HAVE any JOB saved in it!
DELETE ALL JOBS
TOTAL RESET
CONFIRM DELETE ALL JOB?
COUNTER ALARMS RESET Used to reset the counters for all the alarms (Curr. - Tot. ---- see ERROR LOG Menu) that
have occurred in the welding plant.

WARNING: This operation resets the counters for the alarms but does not delete the
DELETE ALL JOBS
individual alarms!
TOTAL RESET
EXECUTE COUNTER ALARMS RESET?
TOTAL RESET Used to return the welding plant to the factory settings.
WARNING: Resetting will take place as soon as the key is released to confirm the
operation!
DELETE ALL JOBS
TOTAL RESET
EXECUTE TOTAL RESET?
43
All the functions included in this menu can be used as
follows:
• Choose the function (e.g. RESET PROCESS DATA) that
DELETE ALL JOBS
DELETE ALL JOBS
DELETE ALL JOBS
you intend to use by rotating the ENCODER KNOB - SX.
TOTAL RESET TOTAL RESET TOTAL RESET
• EXECUTE PROCESS DATA RESETTING by pushing the
DX KEY.
EXECUTE DATA PROCESS RESET? ARE YOU SURE? DATA PROCESS RESET DONE
• PROCEED by finalising the reset by pushing the SX KEY or
cancel the operation by pushing the DX KEY.
To exit the FACTORY RESET Menu and go back to the SETUP Menu:
INFO SETUP Menu

The purpose of this menu is to allow the operator to know what version of the software has been loaded into each component
that is part of the welding plant.
To access the INFO Menu from the SETUP Menu:

POWER SOURCE SW. VERS.

WIRE FEEDER SOFTWARE VER. 1
ROBOT INTERFACE SW. VERS.
S/N
H04-03.04
F03-04.04-BETA0002
C04-24.00
500A
ENCODER KNOB - SX
Software Description
POWER SOURCE SW. VERS. Indicates the version of the software loaded into the welding machine.

S/N
H04-03.04
F03-04.04-BETA0002
C04-24.00
500A
WIRE FEEDER SOFTWARE VERS. 1/2 This indicates the software version loaded in feeder 1/2, if applicable.

S/N
H03-04.00
F02-02.18

S/N
H03-02.03
F02-02.17
(continued)
44
Software Description
ROBOT INTERFACE SW. VERS. This indicates the software version loaded in the robot interface board, if applicable.

S/N
H02-01.00
F06-01.01
S/N This indicates the serial number for the microprocessor contained in the digital interface
board. This is the serial number required for loading special functions at additional cost.

S/N
FX00204904080100
NETWORK BRIDGE SOFTWARE This indicates the network interface software version loaded in the board. There are also
VERSION identity codes that are only required for assistance, and can be requested if the network
malfunctions.

S/N
NETWORK BRIDGE SOFTWARE VERSION
TNI-300415-BETA-0003
DID0 10040204
DID1 106F402E
DC0 017F007F
A diagnostics menu can also be accessed by holding down the DX KEY and the DX KEY for three seconds.
Software Descrizione
DIAGNOSTICS MENU This menu has 4 diagnostics windows:
• CAN BUS STATUS
DIAGNOSTICS
• I/O STATUS
CAN BUS STATUS • REMOTE CONTROLS STATUS
I/O STATUS
REMOTE CONTROL • ENABLED OPTIONS
ENABLED OPTIONS
CAN BUS STATUS Number of packages transmitted and received (Rx.. and TX..) and the number of
transmission errors.
CAN BUS STATUS
Rx packets 98288
Tx packets 59392
Rx FIFO0 98290
Tx errors 0
Rx overruns 0
REC 0
TEC 0
REC max. 0
TEC max. 0
I/O STATUS The status of the inputs and outputs on the generator.
I/O STATUS
FAN OFF
WATER COOLER PUMP OFF
E0.3 UNDER VOLTAGE OFF
E0.2 OVER VOLTAGE OFF
E0.4 OVER CURRENT OFF
T°C THERMAL PROTECTION OFF
VRD OFF
WATER COOLER PRESENCE ON
COOLING PLANT PRESSURE OFF
REMOTE CONTROLS STATUS The status of the inputs:

• ANALOGUE INPUT 1 (synergic remote control input)
REMOTE CONTROL
• ANALOGUE INPUT 2 (arc length remote control input)
ANALOGIC INPUT 1 0 • ANALOGUE INPUTS 3 & 4 not connected
ANALOGIC INPUT 2
ANALOGIC INPUT 3
0
0 • TORCH BUTTON
ANALOGIC INPUT 4
TORCH TRIGGER INPUT
0
OFF • UP AND DOWN BUTTONS on the torch
• AUX-IN not connected
UP TRIGGER INPUT OFF
DOWN TRIGGER INPUT OFF
AUX-IN OFF
(continua)
45
Software Descrizione
ENABLED OPTIONS The special programs enabled, specifically:
• PULSED
ENABLED OPTIONS
• ECP estended curves package
COLD VISION.COLD • VISION.COLD
ECP
PIPE
EXTENDED CURVES PACKAGES
VISION.PIPE • VISION.PIPE
POWER
PULSED
VISION.POWER
PULSED • VISION.POWER
• VISION.ULTRASPEED
ULTSPEED VISION.ULTRASPEED
The contents of thus menu are for information only, the operator cannot change anything they can only read the information con-
tained by scrolling the various options available in the menu by rotating the ENCODER KNOB - SX.
To exit the INFO Menu and go back to the SETUP Menu:

NETWORK SETUP Menu

This menu is used to view the settings for the Ethernet network if connected. If not, the following image is displayed:
LINK STATUS NOT ACTIVE

CONFIGURATION DHCP
IP ADDRESS
NETMASK
GATEWAY
Digitech Vision 5000 [FX00204904080100]
LINK STATUS This indicates that the welding machine has an active connection to the Ethernet
network.

CONFIGURATION DHCP
IP ADDRESS 169.254.136.178
NETMASK 255.255.0.0
GATEWAY 0.0.0.0
CONFIGURATION This indicates the type of network configuration used.

The DHCP protocol is obligatory.

CONFIGURATION DHCP
IP ADDRESS 169.254.136.178
NETMASK 255.255.0.0
GATEWAY 0.0.0.0
IP ADDRESS This indicates the IP address to which the welding machine has been assigned.

CONFIGURATION DHCP
IP ADDRESS 169.254.136.178
NETMASK 255.255.0.0
GATEWAY 0.0.0.0
NETMASK This indicates the sub-network template number to which the welding machine has been
assigned.

CONFIGURATION DHCP
IP ADDRESS 169.254.136.178
NETMASK 255.255.0.0
GATEWAY 0.0.0.0
(continued)
46
GATEWAY This indicates the gateway number to which the welding machine has been assigned.

CONFIGURATION DHCP
IP ADDRESS 169.254.136.178
NETMASK 255.255.0.0
GATEWAY 0.0.0.0
To exit the DATA IN-OUT Menu and go back to the SETUP Menu:
ERROR LOG SETUP Menu

The purpose of this menu is to allow the operator to know, interpret, and understand error conditions that have occurred or may
be encountered on the welding plant.
To access the ERROR LOG Menu from the SETUP Menu:

ERRORS Curr. Tot.

E0.5 REMOTE COMMANDS 0 0
E0.6 WATER COOLER MISSING 1 5
SX KEY E0.7 MOTOR SPEED 0 0 DX KEY
E0.8 WIRE FEEDER MISSING 0 0
T°C THERMAL PROTECTION 0 0
E7.0 RC ANALOGIC MISSING 1 2
VISION SCREEN
Within the menu the following is indicated for each individual error:
• Its code (e.g. E1.0).
• A short description (e.g. no configuration file).
• The number of times this has occurred since the last time the machine was switched on (Curr).
• The number of times this has occurred since the last ALARM COUNTER RESET or TOTAL RESET (Tot.) of the welding machine.
• Errors that have occurred on the welding plant and subsequently been corrected, but not yet partially reset, are highlighted in
yellow.
• Errors that have occurred on the welding machine, but that have not yet been resolved and so are still active, are highlighted
in red.
RESET Curr (RESET PARTIAL ERROR COUNT)

The counter that indicates how many times a error or alarm has occurred since the last time the
machine was switched on is part of this menu, and can be zeroed as follows:
ERRORS
E0.1 OVER AND UNDER VOLTAGE
Curr. Tot.
0 0
• Choose the error for which the partial counter (Curr) must be reset by rotating the SX - ENCODER KNOB.
E0.2 OVER VOLTAGE
E0.3 UNDER VOLTAGE
0
0
0
0
• The VISION SCREEN displays an icon in the bottom right corner (see image) that indicates that you can
E0.4 OVER CURRENT
E0.5 REMOTE COMMANDS
0
0
0
0
proceed with resetting.
E0.6 WATER COOLER MISSING 1 6
• Hold down the DX KEY until resetting of the (Curr) counter has been completed.
Within the menu, by rotating the ENCODER KNOB - SX it is possible to scroll the errors (also indicated in the table below), view them
and select them.
Error
Error code Error description and possible diagnosis
condition
POWER SUPPLY FAILURE
NON automatic reset error.
Err E0.0
This error can only arise when switching on and not when the welding plant is working normally.
Error visible on VISION SCREEN ONLY in the event of a fault and NOT in the ERROR LOG Menu.
(continued)
47
Error
condition
OVER AND UNDER VOLTAGE
Err E0.1
Automatic reset error.
OVER VOLTAGE
Err E0.2
UNDER VOLTAGE
Err E0.3
OVER CURRENT
Err E0.4
REMOTE COMMANDS
Err E0.5 No feed for remote commands.
WATER COOLER MISSING
Check that the WATER COOLER SYSTEM - OBLIGATORY function is included within the
ADVANCED SETUP Menu / EQUIPMENT LAYOUT.
After this initial check you need to know that this error can only occur in the following cases:
• Water cooler system not connected to the welding machine.
• The welding machine does not recognise the water cooler system, even though it is connected
Err E0.6
correctly.
• Water cooler system disconnected when the machine is operating normally.
Once the water cooler system has been reactivated, this error condition resets itself
automatically!
If the alarm occurs even when the WATER COOLER SYSTEM - OPTIONAL function is included in
the ADVANCED SETUP Menu / EQUIPMENT LAYOUT, call Technical Assistance Department
immediately.
MOTOR FAULT
Err E0.7
Immediately contact technical assistance dept.
WIRE FEEDER MISSING
Check that the WIRE FEEDER - OBLIGATORY function is included within the ADVANCED SETUP
Menu / EQUIPMENT LAYOUT.
• Wire feeder not connected to the welding machine.
Err E0.8
• The welding machine does not recognise the wire feeder, even though it is connected correctly.
• Wire feeder disconnected when the machine is operating normally.
Once the wire feeder has been reactivated, this error condition resets itself automatically!
If the alarm occurs even when the WIRE FEEDER - OPTIONAL function is included in the
ADVANCED SETUP Menu / EQUIPMENT LAYOUT, call Technical Assistance Department
immediately.
CAN INTERNAL ERROR
Faulty communication between the generator and the feeder.
Err E0.9
THERMAL PROTECTION
Err T°C The welding stops due to an excessively high temperature (thermostat activated).
COOLER PRESSURE
Err H20 The fluid in the cooling system is at low pressure.
CONFIG. FILE MISSING
Err E1.0
USER FILE MISSING
Err E1.1
TORCH FILE MISSING
Err E1.2
(continued)
48
Error
condition
CALIBRATION FILE MISSING
Err E1.3
MMA DEFAULTS MISSING
Err E1.6
TIG DEFAULTS MISSING
Err E1.7
MIG DEFAULTS MISSING
Err E1.8
WELDER DEFAULTS MISSING
Err E1.9
FILE SYSTEM ERROR
Err E2.0
STICKING
This error is displayed when a short-circuit has been formed between the machine’s output
terminals for more than 1.2 seconds.
Err E3.2
To remove the error state, eliminate the short circuit so that the voltage on the torch goes above the
threshold value again. At this stage the error condition disappears and the welding machine goes
back to the mode prior to the sticking. If the torch trigger is still pushed, it must be released and
pressed again to begin welding again.
MOTOR SPEED FAULT
Err E3.3
Check that the rollers on the wire feeder mechanism are not stuck and that the welding wire comes
out correctly, otherwise contact Technical Assistance Department immediately.
LAST SETUP NOT VALID
Err E4.0
JOBS WRONG
Err E4.1
MIG SYN SPECIAL FUNCTION (Fx) WRONG
Err E4.2
MIG MAN SPECIAL FUNCTION (Fx) WRONG
Err E4.3
SPECIAL PULSED MIG FUNCTIONS (Fx) NOT VALID
Err E4.4
SPECIAL DOUBLE PULSED MIG FUNCTIONS (Fx) NOT VALID
Err E4.5
(continued)
49
Error
condition
MIG PROGRAMS MISSING
Err E5.0
PULSED MIG WELDING PROGRAMMES MISSING
Err E5.1
MMA PROGRAMS MISSING
Err E5.3
TIG PROGRAMS MISSING
Err E5.4
MIG MANUAL PROGRAMS MISSING
Err E5.5
HT5 CAN LINK MISSING
Err E6.0 NON automatic reset error.
ROBOT LINK MISSING
Err E6.1 NON automatic reset error.
NO ROBOT INTERFACE
Err E6.5
RC ANALOGIC MISSING
Check that the ANALOGIC RC - OBLIGATORY function is included within the ADVANCED SETUP
Menu / EQUIPMENT LAYOUT.
• ANALOGIC RC remote control not connected to the relevant connector.
Err E7.0 • The welding plant does not recognise the ANALOGIC RC remote control, even though it is
connected correctly.
• The ANALOGIC RC remote control disconnected when the welding plant is working normally.
As soon as the remote control is connected again this error condition resets itself automatically!
If the alarm occurs even when the ANALOGIC RC - OPTIONAL function is included in the
ADVANCED SETUP Menu / EQUIPMENT LAYOUT, call Technical Assistance Department
immediately.
NO GAS FLOW
Err E8.3
Error reset by a command from the robot’s board (see robot interface manual).
NO H2O FLOW
Err E8.4
NO WELDING WIRE
Err E8.7
POWER LIMITATION
This alarm appears if the power limit is exceeded. The alarm alternates with the standard display
AUT ADJ
every 1.5 seconds, despite which the machine continues to weld, supplying limited power, but
complying with the values shown on the data plate.
The table provides a simple summary of all the error conditions that may arise on the welding plant and, if possible, what the op-
erator must do to attempt to resolve the problem.
The table includes 2 types of errors:
• Automatic reset error: Once the alarm condition has been resolved the welding machine starts working again and the opera-
tor can weld again! The VISION SCREEN goes back to exactly the same point it was at prior to signalling the alarm!
PLEASE NOTE: After resetting has been completed, during normal operation of the machine, the VISION SCREEN will still show
the error signal to inform the operator of the event ( ), but this can be removed visually from the display by simply pushing
the MENU KEY.
WARNING: This only removes the visual error indication but not the history of what happened!
• NON automatic reset error: To remove the alarm status and reinstate correct operation of the machine, the welding plant
must be switched off.
The machine will then be working again and the operator can weld again!
50
PLEASE NOTE: If, when switching on, the error status presents itself again, immediately contact Technical Assis-
tance Department.
This is necessary so that our technical assistance dept (that must be contacted each time the error messages appear on
the welding machine’s operator interface) is able to resolve the problems more easily and as quickly as possible, thanks to
the reports by the user, and also because, in the meantime the welding machine does not allow the operator to do their work.
To exit the ERROR LOG Menu and go back to the SETUP Menu:
ADVANCED SETUP Menu

SETUP
SX KEY DX KEY
VISION SCREEN
To access the ADVANCED SETUP Menu from any point on the control panel:
• Open the SETUP Menu by holding the SX KEY down for at least 5 consecutive seconds.
• Open the CONFIG Menu by rotating the ENCODER KNOB - SX until the icon required is reached, and then push the ENTER/MEM KEY.
• Access the ADVANCED CONFIGURATION function by rotating the ENCODER KNOB - SX and select ACTIVATE by rotating the
ENCODER KNOB - DX.
• Access the ADVANCED WELDING MODE function by rotating the ENCODER KNOB - SX and select ACTIVATE by rotating the EN-
CODER KNOB - DX.
• Access the PLANT CONFIGURATION function by rotating the ENCODER KNOB - SX and select ACTIVATE by rotating the ENCOD-
ER KNOB - DX.
• Exit the CONFIG Menu by pushing the MENU KEY.
• At this stage the SETUP Menu has been transformed into the ADVANCED SETUP Menu and the VISION SCREEN displays the
following additional icons:
- ADVANCED CONFIG
- ADVANCED MODE
- EQUIPMENT LAYOUT
- WELD LOG
Used to exit the ADVANCED SETUP Menu and take the VISION SCREEN back to the
MENU KEY
welding phase.
ENCODER KNOB - SX Used to scroll the various icons (sub-menus) in the menu and then select them.
ENTER/MEM KEY Used to access the menu related to the icon selected.
WARNING:
• It is impossible to weld!
• If the VISION SCREEN is protected by a password, access to this menu will only be allowed by entering the correct password.
51
ACCESSING THE SUB-MENUS
SETUP To access the sub-menus included in the ADVANCED SETUP Menu, you must:
It is not possible to access the ADVANCED SETUP Menu and all the related sub-menus using the “HT5” control panel.
ADVANCED CONFIG ADVANCED SETUP Menu
The purpose of this menu is to allow the operator to know the actual working time and operation of the welding machine, to con-
figure the ENERGY SAVING mode in the best way to allow the best energy saving on the welding plant, and to be able to enable
an analogue output on the welding plant that can be used for connecting total remote controls equipped with automatic self-rec-
ognition.
To access the ADVANCED CONFIG Menu from the ADVANCED SETUP Menu:
ARC ON TIMER 0 gg. 0:00:00

TIMER WELDER ON 0 gg. 0:00:00
ENERGY SAVING STANDARD
SX KEY ERROR FILTER TIME 300 ms DX KEY
VISION SCREEN
Within the ADVANCED CONFIG Menu the operator can view:

ARC ON TIMER Indicates the actual time the machine is used for welding.
WARNING: This time can only be zeroed by means of a TOTAL RESET (see the relevant
paragraph) of the welding plant.
ERROR FILTER TIME 300 ms
TIME WELDER ON Indicates the actual time the machine works, even when the screen saver is activated.
WARNING: This time can only be zeroed by means of a TOTAL RESET (see the relevant
paragraph) of the welding plant.
WARNING: The content of the part of the menu described above is for information only, the operator cannot make any changes,
they can only view and read the information available on the screen.
52
ENERGY SAVING By rotating the ENCODER KNOB - DX (this operation does not require confirmation) it
is possible to choose the energy saving mode you prefer from the 3 available for the
welding plant:
• STANDARD - Energy saving is achieved by the screen saver being activated for the
TIMER WELDER ON
ENERGY SAVING
0 gg. 0:12:49
ULTRA
screens on both the generator and the feeder after a set time that cannot be changed
by the operator (see the relevant paragraph).
• ULTRA - Energy saving is obtained by the screens on the generator and the feeder
being switched off after a set time, equal to that for the screen saver, which cannot be
changed by the operator.
• EXTRA - Energy saving is obtained by the screens on the generator and the feeder
switching off as soon as the machine is switched on.
ERROR FILTER TIME This is used to set the minimum time an alarm remains active before it is displayed.

ENERGY SAVING ULTRA
To exit the ADVANCED CONFIG Menu and go back to the ADVANCED SETUP Menu:
ADVANCED MODE ADVANCED SETUP Menu

The purpose of this menu is to allow the operator to further refine adjustments to the welding parameters for the machine.
To access the ADVANCED MODE Menu from the ADVANCED SETUP Menu:
CYCLE DISABLED
CRATER STANDARD
DUAL PULSE STANDARD
ARC LENGTH ADJUSTMENT VOLTAGE
TIG LIFT MODE DISABLED
VISION SCREEN
Within the ADVANCED MODE Menu it is possible, by rotating the ENCODER KNOB - SX, to choose the advanced welding mode re-
quired from the 4 available (according to the welding process selected) and this can be ACTIVATED (this operation does not
require confirmation) by rotating the ENCODER KNOB - DX.

CYCLE If enabled, when operating in STANDARD or ADVANCED mode, this function provides
the operator with a further welding mode (CYCLE) and the special functions associated
with it, when using MIG (pulsed, double pulsed, synergic, or manual) welding processes:
CYCLE STANDARD
• CURRENT CYCLE, CYCLE WIRE SPEED (see TAB. A/B parameter F19).
CRATER
DUAL PULSE
STANDARD
STANDARD
• CYCLE ARC LENGTH, CYCLE VOLTAGE (see TAB. A/B parameter F20).
ARC LENGTH ADJUSTMENT
TIG LIFT MODE
VOLTAGE
DISABLED
• FIRST SLOPE (from I1 to I2) see TAB. A/B parameter F18) - advanced cycle only.
• SECOND SLOPE (from I2 to I1) (see TAB. A/B parameter F21) - advanced cycle only.
The WELDING MODE SELECTION Menu (MODE) menu will therefore be changed.
This function can only be activated, with the above procedure, on the VISION Display,
whilst it can also be set on the HT5 drag-and-drop once it is activated.
CYCLE ADVANCED
See the special “WELD MODE SELECTION Key” paragraph for correct functioning of the
CRATER
DUAL PULSE
STANDARD
STANDARD
CYCLE welding mode.
(continued)
53
CRATER If enabled, when working in ADVANCED mode, this function provides the operator
with further welding modes related to the CRATER as well as the 2 special functions
explained below that make it possible to vary the length of the arc in the welding crater,
CYCLE ADVANCED
when using MIG (pulsed, double pulsed, synergic, and manual) welding processes.
CRATER
DUAL PULSE
ADVANCED
STANDARD
• INITIAL ARC LENGTH, INITIAL VOLTAGE (see TAB. A/B parameter F09)
TIG LIFT MODE
VOLTAGE
DISABLED
• FINAL ARC LENGTH, FINAL VOLTAGE (see TAB. A/B parameter F14)
DOUBLE PULSED If enabled, when working in ADVANCED mode, this function provides the operator with
the following special functions, when using the double pulsed MIG welding process:
• DOUBLE PULSED ARC LENGTH (F24)
CYCLE ADVANCED
Allows the welder to adjust the length of the arc on both double pulsed levels.
CRATER
DUAL PULSE
STANDARD
ADVANCED
• FIRST SLOPE (from I1 to I2 ) (see TAB. A parameter F22)
TIG LIFT MODE
VOLTAGE
DISABLED
• SECOND SLOPE (from I2 to I1 ) (see TAB. A parameter F27)
These two special functions allow the welder to adjust the ramp for passing between
the two double pulsed levels.
ARC LENGTH ADJUSTMENT This function allows an operator using the (pulsed, double pulsed, synergic and manual)
MIG welding process to adjust the ARC LENGTH ADJUSTMENT ( ) parameter with the
WELDING VOLTAGE ( ) or the WIRE SPEED ( ).
CYCLE DISABLED
CRATER STANDARD
DUAL PULSE STANDARD
TIG LIFT MODE If activated, this function makes an additional welding mode known as TIG LIFT TORCH
TRIGGER available to an operator using the TIG LIFT welding process.
In this mode the welder can control the WELDING CURRENT ( ) parameter, using the
CYCLE DISABLED
button on the TIG torch.
CRATER STANDARD
DUAL PULSE STANDARD
TIG LIFT MODE
VOLTAGE
ENABLED
WARNING: To allow TIG LIFT WITH TORCH TRIGGER welding, the DIGITECH
PULSE needs a specific female connector to be fitted on it (NON-STANDARD
MACHINE) to which the corresponding male connector on the TIG torch is to be
connected.
Therefore, for the TIG LIFT welding process, a new menu will be created (see figure)
named WELDING MODE SELECTION Menu (MODE).
TIG LIFT
TIG LIFT TORCH TRIGGER WELDING MODE SELECTION Menu (MODE)
To access the WELDING MODE SELECTION Menu (MODE) push the MENU KEY.

MENU KEY - Used to access subsequent menus, where applicable.
ENCODER KNOB - SX - Selects the welding mode.
ENTER/MEM KEY - Used to access the PRE-SETTING for the program selected
beforehand, with the welding MODE chosen.
“HT5” CONTROL PANEL

It is not possible to access the WELDING MODE SELECTION Menu (MODE) via the
“HT5” control panel.
To exit the ADVANCED MODE Menu and go back to the ADVANCED SETUP Menu:
54
EQUIPMENT LAYOUT ADVANCED SETUP Menu
The purpose of this menu is to allow the operator to manage connections of components and accessories that are part of the
welding plant.
To access the EQUIPMENT LAYOUT Menu from the SETUP Menu:

EQ. LAYOUT
Within the EQUIPMENT LAYOUT Menu, it is possible, by rotating the ENCODER KNOB - SX, to select the component of the welding
plant, while by rotating the ENCODER KNOB - DX, you can decide the type of connection required (e.g. Optional) or the type of com-
ponent (e.g. Torch 400 A H2O) that is to be connected to the plant (this operation does not require confirmation).

WATER COOLER OPTIONAL - Means that the water cooler system may or may not be connected to the
welding machine.
WATER COOLER OPTIONAL

OBLIGATORY - Means that it is obligatory for the water cooler system to be connected to
WIRE FEEDER 1
REMOTE CONTROL 1
OPTIONAL
RC OPTIONAL
the welding plant.
TORCH TYPE 1
SAFETY CALIBRATION CODE 1
400A H2O
013
A error condition is generated when:
WIRE FEEDER 2
REMOTE CONTROL 2
ABSENT
RC OPTIONAL
• Switching on or at any other time if the welding plant does not detect the presence.
TORCH TYPE 1 400A H2O • During normal operation if the water cooler system is disconnected.
Also see the CONFIG menu if it is necessary to keep the cooling system working
continuously.
WIRE FEEDER 1 / WIRE FEEDER 2 OPTIONAL - This means that FEEDER 1-2 can or cannot be connected to the welding
plant. Once feeder 1-2 is detected when the plant is switched on, its presence becomes
obligatory.
WIRE FEEDER 1
REMOTE CONTROL 1
OPTIONAL
RC OPTIONAL
OBLIGATORY - This means that it is obligatory for FEEDER 1-2 to be connected to the
TORCH TYPE 1
400A H2O
013
welding plant, even when the plant is switched on.
WIRE FEEDER 2
REMOTE CONTROL 2
ABSENT
RC OPTIONAL
TORCH TYPE 1 400A H2O • When switched on, if the welding plant does not detect its presence.
• During normal operation if the wire feeder is disconnected.

MISSING - Means that feeder 2 must not be managed by the plant, even if it is
WIRE FEEDER 1
REMOTE CONTROL 1
OPTIONAL
RC OPTIONAL
connected up.
TORCH TYPE 1 400A H2O NOTE: If the second feeder is not connected up, all the settings relate to feeder 1.
SAFETY CALIBRATION CODE 1 013
WIRE FEEDER 2 ABSENT NOTE: The FEEDER 2 section must also be set to allow feeder 2 to work in a robotised
REMOTE CONTROL 2 RC OPTIONAL
TORCH TYPE 1 400A H2O plant.
(continued)
55
REMOTE CONTROL 1 / DISABLED - Means that REMOTE CONTROL 1-2 must not be managed by the plant,
REMOTE CONTROL 2 even if it is connected up.
OPTIONAL - This means that REMOTE CONTROL 1-2 can or cannot be connected to
the welding plant. If it is disconnected while the plant is running, no alarm is raised.
WIRE FEEDER 1 OPTIONAL
TORCH TYPE 1
400A H2O
013
OBLIGATORY - This means that it is obligatory for REMOTE CONTROL 1-2 to be
WIRE FEEDER 2
REMOTE CONTROL 2
ABSENT
RC OPTIONAL
connected to the welding plant, even when the plant is switched on.
TORCH TYPE 1 400A H2O

• Switching on or at any other time if the welding plant does not detect the presence (only
if set as obligatory).
WIRE FEEDER 1
REMOTE CONTROL 1
OPTIONAL
RC OPTIONAL
• During normal operation, if the remote control is disconnected.
WIRE FEEDER 2 ABSENT WARNING: For indications on use and functioning of the ANALOGIC RC remote
TORCH TYPE 1 400A H2O control see the manuals for the welding machine and the wire feeder, enclosed with the
documentation.
TORCH TYPE 1 / TORCH TYPE 2 Used to set the TORCH TYPE 1/2 that will subsequently be connected to the welding
plant. This operation must be done in order to size the plant correctly and as a result, the
welding parameters.
WIRE FEEDER 2 ABSENT

WIRE FEEDER 2 ABSENT

EQ. LAYOUT
When in the CONFIG menu, rotate the ENCODER KNOB - SX to select activation of robot configuration.
NOTE: If robot configuration is activated when no robot interface is connected, an error message will be displayed and it will not
be possible to weld.
Funzione avanzata Descrizione

ROBOT WELDING DISABLED - Means that manual welding is used.
ENABLED - Means that welding is enabled with the robot interface board. Once this
function has been selected, the welding plant will require the robot interface board to be
ROBOT CONN. MODE
ROBOT REG. MODE
RI-A 1
ABS. WIRE SP.
connected correctly. If this is not the case, an error message will be displayed and it will
TENSIONE DA ROBOT
IND. ELETTR. DA ROBOT
ENABLED
DISABLED
not be possible to weld.
ROBOT BURN BACK DISABLED
ROBOT DYNAMICS DISABLED
ROBOT PULSE FREQ. DISABLED
GAS FLUX CONTROL DISABLED
(continua)
56
ROBOT CONN. MODE (ROBOT RI-A 1 - Means that the presence of an interface board for analogue / digital type robots
CONNECTION MODE) is detected
RI-D 2 - Means that the presence of an interface board for Device net type robots is
detected
ROBOT CONN. MODE RI-A 1
ROBOT REG. MODE ABS. WIRE SP.
TENSIONE DA ROBOT
IND. ELETTR. DA ROBOT
ENABLED
DISABLED
------- - Means that no type of robot board is detected
ROBOT REG. MODE (ROBOT ASS. CURRENT - In this mode, a MINIMUM ROBOT ANALOGUE V - MAXIMUM
REGULATION MODE) ROBOT ANALOGUE V (*) input corresponds to a current supplied of 0-500A.
REL. CURRENT - In this mode, a MINIMUM ROBOT

ANALOGUE V - MAXIMUM ROBOT ANALOGUE V (*) input corresponds to extreme
ROBOT CONN. MODE
ROBOT REG. MODE
RI-A 1
ABS. WIRE SP.
currents on the welding curve used.
TENSIONE DA ROBOT ENABLED
IND. ELETTR. DA ROBOT DISABLED
ROBOT BURN BACK DISABLED ASS. WIRE SPEED - In this mode, a MINIMUM ROBOT ANALOGUE V - MAXIMUM
ROBOT ANALOGUE V (*) input corresponds to a wire speed of 0-25 m/min.
REL. WIRE SPEED - In this mode, a MINIMUM ROBOT ANALOGUE V - MAXIMUM

ROBOT ANALOGUE V (*) input corresponds to extreme wire speeds on the welding
curve used.
(*) These values can be set as described below.

ROBOT VOLTAGE NOT ACTIVE - In this mode, regulation of the ARC LENGTH is active, via the welding
machine’s panel.

ACTIVE - In this mode, regulation of the ARC LENGTH is active, via the robot interface
ROBOT CONN. MODE
ROBOT REG. MODE
RI-A 1
ABS. WIRE SP.
board.
ROBOT VOLTAGE ENABLED
ROBOT ELECTRONIC INDUCTANCE DISABLED
ROBOT ELECTRONIC INDUCTANCE NOT ACTIVE - In this mode, regulation of the ELECTRONIC INDUCTANCE is active, via
the welding machine’s panel.

ACTIVE - In this mode, regulation of the ELECTRONIC INDUCTANCE is active, via the
ROBOT CONN. MODE
ROBOT REG. MODE
RI-A 1
ABS. WIRE SP.
robot interface board.
ROBOT BURN BACK NOT ACTIVE - In this mode, regulation of the BURN BACK is active, via the welding
machine’s panel.

ACTIVE - In this mode, regulation of the BURN BACK is active, via the robot interface
ROBOT CONN. MODE
ROBOT REG. MODE
RI-A 1
ABS. WIRE SP.
board.
ROBOT DYNAMICS NOT ACTIVE - In this mode, DYNAMIC regulation is active, via the welding machine’s
panel.

ACTIVE - In this mode, DYNAMIC regulation is active, via the robot interface board.
(continua)
57
ROBOT PULSE FREQ. (ROBOT PULSE NOT ACTIVE - In this mode, PULSATION FREQUENCY regulation is active, via the
FREQUENCY) welding machine’s panel.
ACTIVE - In this mode, PULSATION FREQUENCY regulation is active, via the robot
interface board.
GAS FLUX CONTROL NOT ACTIVE - In this mode the GAS FLOW input for the MCB-3 motor control box is
ignored.

ACTIVE - In this mode the GAS FLOW input for the MCB-3 motor control box is checked,
ROBOT CONN. MODE
ROBOT REG. MODE
RI-A 1
ABS. WIRE SP.
and if necessary the relevant alarm is activated.
WATER FLUX CONTROL NOT ACTIVE - In this mode the WATER FLOW input for the MCB-3 motor control box is
ignored.

ACTIVE - In this mode the WATER FLOW input for the MCB-3 motor control box is
ROBOT REG. MODE
ROBOT VOLTAGE
ABS. WIRE SP.
ENABLED
tested, and if necessary the relevant WATER FAULT alarm is activated via the output of
ROBOT ELECTRONIC INDUCTANCE
ROBOT BURN BACK
DISABLED
DISABLED
the box.
WATER FLUX CONTROL DISABLED
WIRE PRESENCE CONTROL NOT ACTIVE - In this mode the WIRE PRESENCE input for the MCB-3 motor control
box is ignored.

ACTIVE - In this mode the WIRE PRESENCE input for the MCB-3 motor control box is
ROBOT VOLTAGE
ROBOT ELECTRONIC INDUCTANCE
ENABLED
DISABLED
tested, and if necessary the relevant WIRE MISSING alarm is activated via the robot
ROBOT BURN BACK
ROBOT DYNAMICS
DISABLED
DISABLED
interface board.
WIRE PRESENCE CONTROL DISABLED
CURRENT MISSING MASK XXX [ms] - During and on completion of welding, this indicates the time lapse between
current zeroing and deactivation of the CURRENT SENSE digital output on the robot
interface board.
CURRENT MISSING MASK 300 ms
DUAL FEEDER MODE SEPARATE - If a double feeder is chosen in the EQUIPMENT LAYOUT menu, in this
mode the second feeder operates separately from the first.

SLAVED - If a double feeder is chosen in the EQUIPMENT LAYOUT menu, in this mode
ROBOT BURN BACK
ROBOT DYNAMICS
DISABLED
DISABLED
the second feeder operates simultaneously with and parallel to the first.
DUAL FEEDER MODE STAND ALONE
SLAVE FEEDER SPEED The parameter indicates the speed difference in ‰ for the slave feeder, compared to the
main feeder.

SLAVE FEEDER SPEED +0‰
(continua)
58
MIN. ROBOT ANALOG VOLTAGE These parameters are used to set the maximum and minimum voltage settings used to
control the robot board’s analogue inputs.
The settable values are:
MINIMUM ROBOT ANALOGUE V from 0V to 2V
ROBOT PULSE FREQ.
GAS FLUX CONTROL
DISABLED
DISABLED
MAXIMUM ROBOT ANALOGUE V from 5V to 14,5V
MIN. ROBOT ANALOG VOLTAGE 0.0 V
MAX. ROBOT ANALOG VOLTAGE

MIN. ROBOT ANALOG VOLTAGE 0.0 V
MAX. ROBOT ANALOG VOLTAGE 10.0 V
To exit the EQUIPMENT LAYOUT Menu and go back to the ADVANCED SETUP Menu:
WELD LOG ADVANCED SETUP Menu

The purpose of this menu is to allow the operator to know the latest welding parameters set on the machine, as well as the lat-
est data saved on the machine.
To access the WELD LOG Menu from the ADVANCED SETUP Menu:
SET POINT
SX KEY CURRENT 39 [A] VOLTAGE 1.2 [V] DX KEY
HOLD DATA
CURRENT 39 [A] VOLTAGE 1.2 [V]
VISION SCREEN
The content of this menu is for information only, the operator cannot make any changes, they can only read the information avail-
able on the screen.
To exit the WELD LOG Menu and go back to the ADVANCED SETUP Menu:
59
C.so E. Filiberto, 27 - 23900 LECCO - ITALY
Cas. Post. (P.O. BOX) 205
Tel. +39 0341 22322 - Fax +39 0341 422646
[email protected]
www.ceaweld.com
ISO 9001: 2008

Cea Convex 400 Manual

Uploaded by

Copyright:

Available Formats

Cea Convex 400 Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cea Convex 400 Manual

Uploaded by

Copyright:

Available Formats

EN Operator’s manual READ CAREFULLY

CEA COSTRUZIONI ELETTROMECCANICHE ANNETTONI S.p.A.

C.so E. Filiberto, 27 - 23900 Lecco - Italy

MIG-MAG welding 2A - Connecting the cables - Welding with a POSITIVE

REMOTE CONTROL ANALOGIC RC

The pointing out of any difficulties

Replacing the digital interface PCB

Power supply switch Positive pole snap-in connector

Product suitable for free circulation in the Warning!

Before using the equipment you should

Grounding Special disposal

CONVEX vision EN Spare parts list READ CAREFULLY

3300 STEEL PRO - 4000 - 5000

CEA COSTRUZIONI ELETTROMECCANICHE ANNETTONI S.p.A.

C.so E. Filiberto, 27 - 23900 Lecco - Italy

CEA COSTRUZIONI ELETTROMECCANICHE ANNETTONI S.p.A.

C.so E. Filiberto, 27 - 23900 Lecco - Italy

Welding machine control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Wire feeder control panel (not used with DH 32 and VS 32) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Switching on the welding machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

WELDING PROCESS SELECTION Menu (PROCESS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ADVANCED SETUP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Welding machine control panel

ENCODER KNOB - SX ENCODER KNOB - DX

Wire feeder control panel (not used with DH 32 and VS 32)

PARAMETER SELECTION LED - A PARAMETER DISPLAY SCREEN - V

TWO STROKE (2T) 2T LED ( ) switched on

MENU KEY ENTER/MEM KEY

ENCODER KNOB - SX ENCODER KNOB - DX

VISION Screen Display HT5 (not used with DH 32 and VS 32)

“DH” / “VS” CONTROL PANEL

1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2

MENU KEY ENTER/MEM KEY

1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2

MENU KEY Provides access to the next menus.

The following processes are available:

1 - PROGRAM SELECTION Menu (PROGRAM)

“DH” / “VS” CONTROL PANEL

PRG MATERIAL Ø GAS

MENU KEY Used to access subsequent menus if there are any.

“HT5” CONTROL PANEL (not used with DH 32 and VS 32)

2 - WELDING MODE SELECTION Menu (MODE)

“DH” / “VS” CONTROL PANEL

TWO STROKE (2T)

1011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2

MENU KEY Used to access subsequent menus if there are any.

WELDING MODE SELECTION KEY

WELDING MODE SELECTION LED

3 - SPECIAL FUNCTIONS Menu (SET UP Fx)

“DH” / “VS” CONTROL PANEL

ENCODER KNOB - SX ENCODER KNOB - DX

MENU KEY Used to access subsequent menus if there are any.

PARAMETER DISPLAY SCREEN - V

SPECIAL FUNCTIONS (FX) KEY

PARAMETER DISPLAY SCREEN - A Displays the selected SPECIAL FUNCTION (Fx).

PARAMETER DISPLAY Screen - V Welding mode

Screen - A STITCH WELDING

PRE GAS PrG 0.1s (0.0 - 2.0)s ● ● ● ● ● ● ● ●

FOUR STROKE (4T)

TWO STROKE (2T)